Features. Description. Models Adjustable Output Current Range. 600W Programmable IP67 Driver. ESD-600SxxxDV

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Features. Description. Models Adjustable Output Current Range. 600W Programmable IP67 Driver. ESD-600SxxxDV"

Transcription

1 ESD600SxxxDV Features Ultra High Efficiency (Up to 95%) Full Power at Wide Output Current Range (Constant Power) Thermal Sensing and Protection for LED Module 010V/PWM/Timer Dimmable (3 Timer Modes) DimtoOff with Standby Power 1.5 W Output Lumen Compensation Input Surge Protection: 6kV lineline, 10kV lineearth AllAround Protection: OVP, SCP, OTP Waterproof (IP67) SELV Output Suitable for Independent Use 5 Years Warranty Description The ESD600SxxxDV series is a 600W, constantcurrent, programmable LED driver that operates from Vac input with excellent power factor. Created for high mast, sports, aquaculture and horticulture lighting, it provides a dimtooff mode with low standby power. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure troublefree operation, protection is provided against input surge, under voltage lock out, input over voltage, output over voltage, short circuit, and over temperature. Models Adjustable Output Current Range FullPower Current Range(1) Default Output Current A A 2.1A A A 2.8 A A A 4.2 A A A 5.6 A A A A A 7.0 A 9.8 A A A 12.5 A Input Voltage Range(2) Output Voltage Range Max. Output Power Typical Efficiency (3) Power Factor 277Vac 480Vac Model Number 249~528Vac 143 ~ 357Vdc 600 W 352~500Vdc 95.0% ESD600S210DV 249~528Vac 108 ~ 268Vdc 600 W 352~500Vdc 94.5% ESD600S280DV 249~528Vac 352~500Vdc 249~528Vac 352~500Vdc 249~528Vac 352~500Vdc 249~528Vac 352~500Vdc 249~528Vac 352~500Vdc 72 ~ 178Vdc 600 W 95.0% ESD600S420DV 54 ~ 134Vdc 600 W 95.0% ESD600S560DV 41 ~ 101Vdc 600 W 94.5% ESD600S740DV(4) 31 ~ 76Vdc 600 W ESD600S980DV(4) 24 ~ 60Vdc 600 W ESD600S12ADV(4) Notes: (1) Output current range with constant power at 600W (2) Certified voltage range: Vac or Vdc (3) Measured at full load and 480Vac input (see below General Specifications for details). (4) SELV Output 1 / 15 Tel: Fax:

2 ESD600SxxxDV ESD600S210DV IV Operating Area ESD600S280DV ESD600S420DV ESD600S560DV ESD600S740DV ESD600S980DV 2 / 15 Tel: Fax:

3 ESD600SxxxDV ESD600S12ADV Input Specifications Input Voltage 249 Vac 528 Vac Vdc Input Frequency 47 Hz 63 Hz Leakage Current 0.70 ma Input AC Current Inrush Current(I 2 t) 20.4 A 2 s PF 0.90 THD 20% IEC605981; 480Vac/ 60Hz, Grounding effectively 2.50 A Measured at full load and 277 Vac input A Measured at full load and 480 Vac input. At 480Vac input, 25 cold start, duration=869 μs, 10%Ipk10%Ipk. See Inrush Current Waveform for the details. At Vac, 5060Hz, 60%100% Load ( W) Output Specifications Output Current Tolerance 5%Ioset 5%Ioset At full load condition Output Current Setting(Ioset) Range ESD600S210DV ESD600S280DV ESD600S420DV ESD600S560DV ESD600S740DV ESD600S980DV ESD600S12ADV 168 ma 224 ma 336 ma 448 ma 592 ma 784 ma 1000 ma 2100 ma 2800 ma 4200 ma 5600 ma 7400 ma 9800 ma ma 3 / 15 Tel: Fax:

4 ESD600SxxxDV Output Specifications Output Current Setting Range with Constant Power ESD600S210DV ESD600S280DV ESD600S420DV ESD600S560DV ESD600S740DV ESD600S980DV ESD600S12ADV Total Output Current Ripple (pkpk) Output Current Ripple at < 200 Hz (pkpk) 1680 ma 2240 ma 3360 ma 4480 ma 5920 ma 7840 ma ma 2100 ma 2800 ma 4200 ma 5600 ma 7400 ma 9800 ma ma 5%Iomax 10%Iomax At full load condition, 20 MHz BW 2%Iomax Startup Overshoot Current 10%Iomax At full load condition No Load Output Voltage ESD600S210DV ESD600S280DV ESD600S420DV ESD600S560DV ESD600S740DV ESD600S980DV ESD600S12ADV 390V 290 V 198 V 153 V 110 V 85 V 70 V At full load condition. Only this component of ripple is associated with visible flicker. Line Regulation ±0.5% Measured at full load Load Regulation ±1.5% Turnon Delay Time 0.75 s Temperature Coefficient of Ioset 12V Auxiliary Output Voltage 10.8 V 12 V 13.2 V 12V Auxiliary Output Source Current Measured at Vac input, 60%100% Load 0.03%/C Case temperature = 0C ~Tc max 0 ma 200 ma Return terminal is Dim Note: All specifications are typical at 25C unless otherwise stated. 4 / 15 Tel: Fax:

5 ESD600SxxxDV General Specifications Efficiency at 277 Vac input: ESD600S210DV Io= 1680 ma Io= 2100 ma ESD600S280DV Io= 2240 ma Io= 2800 ma ESD600S420DV Io= 3360 ma Io= 4200 ma ESD600S560DV Io= 4480 ma Io= 5600 ma ESD600S740DV Io= 5920 ma Io= 7400 ma ESD600S980DV Io= 7840 ma Io= 9800 ma ESD600S12ADV Io= ma Io= ma Efficiency at 347 Vac input: ESD600S210DV Io= 1680 ma Io= 2100 ma ESD600S280DV Io= 2240 ma Io= 2800 ma ESD600S420DV Io= 3360 ma Io= 4200 ma ESD600S560DV Io= 4480 ma Io= 5600 ma ESD600S740DV Io= 5920 ma Io= 7400 ma ESD600S980DV Io= 7840 ma Io= 9800 ma ESD600S12ADV Io= ma Io= ma 91.0% 90.5% 90.5% 89.5% 91.0% 90.0% 91.0% 91.0% 90.5% 90.5% 95.0% 94.5% 94.5% Measured at full load and steadystate temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at full load and steadystate temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) 5 / 15 Tel: Fax:

6 ESD600SxxxDV General Specifications (Continued) Efficiency at 480 Vac input: ESD600S210DV Io= 1680 ma Io= 2100 ma ESD600S280DV Io= 2240 ma Io= 2800 ma ESD600S420DV Io= 3360 ma Io= 4200 ma ESD600S560DV Io= 4480 ma Io= 5600 ma ESD600S740DV Io= 5920 ma Io= 7400 ma ESD600S980DV Io= 7840 ma Io= 9800 ma ESD600S12ADV Io= ma Io= ma 91.0% 91.0% 95.0% 94.5% 94.5% 95.0% 94.5% 95.0% 94.5% 94.5% Measured at full load and steadystate temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Standby power 1.5 W Measured at 480Vac/50Hz; Dimming off MTBF Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w 200,000 Hours 101,000 Hours 40 C +89C Measured at 480Vac input, 80%Load and 25C ambient temperature (MILHDBK 217F) Measured at 480Vac input, 80%Load and 70C case temperature; See lifetime vs. Tc curve for the details 40 C +75C Case temperature for 5 years warranty Storage Temperature 40 C +85 C Humidity: 5%RH to 100%RH Dimensions Inches (L W H) Millimeters (L W H) Net Weight 3330 g Note: All specifications are typical at 25C unless otherwise stated. Dimming Specifications With mounting ear Absolute Maximum Voltage on the Vdim (+) Pin 20 V 20 V Source Current on Vdim (+)Pin 200 ua 300 ua 450 ua Vdim(+) = 0 V 6 / 15 Tel: Fax:

7 ESD600SxxxDV Dimming Specifications Dimming Output Range ESD600S210DV ESD600S280DV ESD600S420DV ESD600S560DV ESD600S740DV ESD600S980DV ESD600S12ADV ESD600S210DV ESD600S280DV ESD600S420DV ESD600S560DV ESD600S740DV ESD600S980DV ESD600S12ADV Recommended Dimming Input Range 10%Ioset Ioset 168 ma 224 ma 336 ma 448 ma 592 ma 784 ma 1000 ma Ioset 0 V 10 V Dim off Voltage 0.35 V 0.5 V 0.65 V Dim on Voltage 0.55 V 0.7 V 0.85 V 1680mA Ioset 2100mA 2240 ma Ioset 2800 ma 3360mA Ioset 4200mA 4480mA Ioset 5600mA 5920 ma Ioset 7400 ma 7840 ma Ioset 9800 ma ma Ioset ma 168mA Ioset <1680mA 224 ma Ioset < 2240 ma 336mA Ioset < 3360mA 448mA Ioset < 4480mA 592 ma Ioset < 5920 ma 784 ma Ioset < 7840 ma 1000 ma Ioset < ma Default 010V dimming mode. Hysteresis 0.2 V PWM_in High Level 3 V 10 V PWM_in Low Level 0.3 V 0.6 V PWM_in Frequency Range 200 Hz 3 KHz PWM_in Duty Cycle 1% 99% PWM Dimming off (Positive Logic) PWM Dimming on (Positive Logic) PWM Dimming off ( Negative Logic) PWM Dimming on ( Negative Logic) 3% 5% 8% 5% 7% 10% 92% 95% 97% 90% 93% 95% Hysteresis 2% Note: All specifications are typical at 25 C unless stated otherwise. Dimming mode set to PWM in PC interface. Safety &EMC Compliance Safety Category Standard CE EN , EN EMI Standards EN (1) EN EN Notes Conducted emission Test &Radiated emission Test Harmonic current emissions Voltage fluctuations & flicker 7 / 15 Tel: Fax:

8 ESD600SxxxDV Safety &EMC Compliance EMS Standards Notes EN EN Electrostatic Discharge (ESD): 8 kv air discharge, 4 kv contact discharge RadioFrequency Electromagnetic Field Susceptibility TestRS EN Electrical Fast Transient / BurstEFT EN Surge Immunity Test: AC Power Line: line to line 6 kv, line to earth 10 kv (2) EN EN EN EN Conducted Radio Frequency Disturbances TestCS Power Frequency Magnetic Field Test Voltage Dips Electromagnetic Immunity Requirements Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. (2) To perform electric strength (hipot) testing, the GDT ground disconnect (nut and metal lock sheet) on the driver endcap should be removed temporarily to prevent the internal gas discharge tube from conducting (as allowed by IEC Clause 10.2). After testing is completed, these items must be reinstalled to restore linetoearth surge protection and secure the end cap. Lifetime vs. Case Temperature 8 / 15 Tel: Fax:

9 ESD600SxxxDV Inrush Current Waveform Efficiency vs. Load ESD600S210DV(lo=1680mA) ESD600S210DV(lo=2100mA) ESD600S280DV(lo=2240mA) ESD600S280DV(lo=2800mA) 9 / 15 Tel: Fax:

10 ESD600SxxxDV ESD600S420DV(lo=3600mA) ESD600S420DV(lo=4200mA) ESD600S560DV(lo=4480mA) ESD600S560DV(lo=5600mA) ESD600S740DV(lo=5920mA) ESD600S740DV(lo=7400mA) 10 / 15 Tel: Fax:

11 ESD600SxxxDV ESD600S980DV(lo=7840mA) ESD600S980DV(lo=9800mA) ESD600S12ADV(lo=10000mA) ESD600S12ADV(lo=12500mA) Power Factor 11 / 15 Tel: Fax:

12 ESD600SxxxDV Total Harmonic Distortion Protection Functions External Thermal Protection NTC R kohm R kohm Protection Current Floor When R_NTC falls below R1, External Thermal Protection is triggered, reducing output current until R2 is reached. When R_NTC is less than R2, output current is reduced to the programmed Protection Current Floor. 10%Ioset 60%Ioset 100%Ioset 10%Ioset>Iomin (default setting is 60%) Iomin 60%Ioset 100%Ioset 10%Ioset Iomin (default setting is 60%) Over Temperature Protection Short Circuit Protection Over Voltage Protection Decreases output current, returning to normal after over temperature is removed. Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Limits output voltage at no load and in case the normal voltage limit fails. Dimming 010V Dimming The recommended implementation of the dimming control is provided below. Implementation 1: DC Input 12 / 15 Tel: Fax:

13 ESD600SxxxDV Notes: 1. The dimmer can also be replaced by an active 010V voltage source signal or passive components like resistors and zener. 2. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 3. If 010V dimming is not used, Dim + should be open. PWM Dimming The recommended implementation of the dimming control is provided below. Implementation 2: Positive logic Implementation 3: Negative logic Time Dimming Time dimming control includes 3 kinds of modes, they are Self AdaptingMidnight, Self Adapting Percentage and Traditional Timer. Self AdaptingMidnight: Automatically adjusts the dimming curve based on the ontime of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self AdaptingPercentage: Automatically adjusts the ontime of each step by a constant percentage = (actual ontime for the past 2 days if difference <15 min) / (programmed ontime from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes. Output Lumen Compensation Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. 13 / 15 Tel: Fax:

14 ESD600SxxxDV Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRGMUL2 (Programmer) datasheet for details. Mechanical Outline INPUT (VDE H07RNF 3*1.0mm 2 9.0) DIMMING WIRE (VDE 5*0.5mm 2 7.2) Tc V+(BROWN) V (BLUE) GRAY PURPLE BLACK/WHITE BLUE/WHITE PINK AC/L(BROWN) AC/N (BLUE) GND(YELLOW/GREEN) OUTPUT (VDE H07RNF 2*1.5mm 2 9.4) PROJ: Unspecified tolerance:±1 RoHS Compliance Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products. 14 / 15 Tel: Fax:

15 ESD600SxxxDV Revision History Change Date Rev. Description of Change Item From To A Datesheets Release / / Operating Area ESD600S420/560DV Added Input Specifications PF/THD Updated Output Current Setting(Ioset) Range ESD600S420/560DV Added Output Current Setting Range with Constan ESD600S420/560DV Power Added B No Load Output Voltage ESD600S420/560DV Added Efficiency at 277 Vac input ESD600S420/560DV Added Efficiency at 347 Vac input ESD600S420/560DV Added Efficiency at 480 Vac input ESD600S420/560DV Added Dimming Output Range ESD600S420/560DV Added Efficiency vs. Load ESD600S420/560DV Added Features 5 Years Warranty Added Models ESD600S210DV Added IV Operation Area ESD600S210DV Added Output Current Setting(Ioset) Range ESD600S210DV Added Output Current Setting Range with Constant Power ESD600S210DV Added C No Load Output Voltage ESD600S210DV Added Efficiency at 277Vac input ESD600S210DV Added Efficiency at 347 Vac input ESD600S210DV Added Efficiency at 480 Vac input ESD600S210DV Added General Specifications Operating Case Temperature for Warranty Tc_w Updated Dimming Specifications ESD600S210DV Added Efficiency vs. Load ESD600S210DV Added 15 / 15 Tel: Fax: