6RZ. > <8ms and <30ms performance versions > Single and dual element versions > Draw out case > Flush panel or rack mount > Made in Australia

Transcription

1 High Speed Interposing Relay The Series comprises a range of compact low burden interposing relays for power utility protection and control applications. > <8ms and <30ms performance versions > Single and dual element versions > Draw out case > Flush panel or rack mount > Made in Australia 6 R Z F 0 4 / 1 0 /

2 Description Cross Reference MVAZ09 MVAZ19 MVAZ29 Code Features > Optional pick-up LED indicators > Optional contact configuration > Optional input shunt resistor > Low burden > <8ms & <30ms pick-up time versions > Size 2M28-S draw out case Description The Series are All or Nothing relays housed in a size 2 draw out case for rack or flush mounting. 6 contacts per element are provided: 2 N/O + 4 N/C 4 N/O + 2 N/C 6 N/O Three main versions are available: 09 A single element relay with an operate time of <8ms. 19 A two element relay with an operate time of <30ms. 29 A two element relay with an operate time of <8ms. Application Contact multiplication and isolation of input and output signals.

3 Technical Data Options Operate Voltage Operate LED One per element Nominal Operate Voltage 125V dc Input shunt resistor Quantity: Function: Value : Rating: One per element Allows a small current to flow in the operate circuit for voltages below the relay minimum operate threshold. This current may be used to operate an external low power LED to signal that a voltage is applied to the element. 125V dc 22K ohm 2W Minimum Operate Voltage Non-operate Voltage Maximum Voltage Minimum Dropout Voltage Burden 09, 19, 29 at 125V dc: Input shunt resistor: Operate Time V dc 65V dc 140V dc 15V dc <7W per element Add 0.75W per element Class Very fast Operate Time <8ms Release Time 15ms 19 Class Fast Operate Time <30ms Release Time 15ms 29 Class Very fast Operate Time <8ms Release Time 15ms Contact Ratings Maximum Contact Power 300W resistive 225W inductive L/R = 7ms Maximum Break Capacity 125V dc L/R = 40ms 0.2A Make and Carry 125V dc resistive 1A continuous 15A for 1s 30A for 200ms Make and Carry 125V dc L/R = 0ms 25A for 200ms AC Resistive 10A Minimum Load 30mA / 24V dc

4 Compliance Data Insulation IEC Type Any Terminal and Earth Between Independent Circuits Across Normally Open Contacts Level High Frequency Disturbance 2.0kV ac rms for 1min 5.0kV 1.2/50us 0.5J 2.0kV ac rms for 1min 5.0kV 1.2/50us 0.5J 1.0kV ac rms for 1min IEC Common (Longitudinal) 2.5kV 5% Differential (Transverse) 1.0kV 5% Electrostatic Discharge IEC Class 3 Contact Discharge 8.0kV 5% Fast Transients IEC Class A 5/50ns 100kHz 4.0kV 5% Surge Immunity IEC Between all Terminals and Earth Between any Two Independent Circuits 4.0kV 2.0kV 10% Temperature IEC /2 Operating Range Storage Range Humidity -10 to +55 degrees Celsius -25 to +70 degrees Celsius IEC Operating Range IP Rating IEC Installed Vibration - Sinusoidal 40 degrees Celsius and 93% RH non condensing IP5x IEC Class I Vibration Response 0.5gn 5% Vibration Endurance 1.0gn 5% Shock and Bump IEC Class I Shock Response 5gn, 11ms 5% Shock Withstand 15gn, 11ms 5% Bump Test 10gn, 16ms 5% Seismic IEC Class I Seismic Response 1gn 5% Mechanical Classification Durability >10 6 operations at no load Conducted Radio Frequency Interference IEC to 80MHz 10V 5% Radiated Immunity IEC Class III 80MHz to 2,760MHz 10V/m 5%

5 Wiring Diagram Wiring Configuration Contact Configuration Top Element Case Terminal Number Pairs M+4B B B M B B M 4 4M+2B B M M B M M 6 6M M M M M M M Contact Configuration Bottom Element Case Terminal Number Pairs M+4B B B M B B M 4 4M+2B B M M B M M 6 6M M M M M M M The case termination diagrams depicts the rear screw terminals and position of the operate coils for all relay versions. The contact function between each pairs of terminals is determined by the order code selected. M B Normally open Make (M) contact This contact closes when the relay operate coil is energized. Normally closed Break (B) contact This contact opens when the relay operate coil is energized. Table 1 provides the terminal wiring assignment for each of the contact configurations available with the relay RELAY 1 RELAY 2 RELAY RELAY 1 RELAY Case termi nations (REAR VIEW)

6 Case Dimensions 2M28-S Front View Rear View Panel Cut-out Side View Size 2M28-S draw out case Drawing units: mm Suits flush panel mounting & 4U high 19 inch rack frame 2 holes of 3.7

7 Order Codes Order Codes - Configuration 09 Single element - <8ms P/U 19 Dual element - <30ms P/U 29 Dual element - <8ms P/U Nominal Operate Voltage E 125 V dc Contact Configuration per element 2 2 N/O + 4 N/C 4 4 N/O + 2 N/C 6 6 N/O Options - No options required (Select all option codes required) L Coil operation LED R Input shunt resistor

8 Image of back of unit to go here Image of back of unit to go here Rel ay Monito ri n g Sy st em s P ty L td d e si g n, manufa ctur e and ma rk et a w i de r ange of el ectric al pro tec tio n a nd contro l p roduc ts for a p pl ica tio n o n h i g h volt age pow er sy st em s. The co mpany' s d ep t h of manufa ctur i ng a n d en gi n ee ri n g e xper ti se i s backed u p by ma ny y e ars of exper i enc e si nc e t h e form ation of it s p r ed ec es sor, Rel ays P ty L t d (RPL), i n This exper i enc e combi ne d with a bro ad ba se of fie l d proven pro d uct ty p es e na b le s R MS to se rv ice sp ec ific c us to mer ne e ds by pro d ucing re la ys o n d ema n d and with typica ll y sho rt lea d t im e s.