PSG series 2000 Iss5 10/25/00 11:20 AM Page 1 SERIES SELECTION GUIDE. Industrial Temperature and Process Controllers ALL SOLUTIONS.

Transcription

1 PSG series 000 Iss5 0/5/00 :0 AM Page SERIES 000 SELECTION GUIDE Industrial Temperature and Process Controllers ONE RANGE ALL SOLUTIONS abc

2 PSG series 000 Iss5 0/5/00 :0 AM Page ONE RANGE ALL SOLUTIONS Representing over 30 years of advanced design and applications experience in industrial temperature and process control, Series 000 is the most complete family available today. It includes a full range of temperature controllers, process controllers, indicators and alarm units. Series 000 is available in a wide range of sizes with features designed to provide accurate, trouble-free performance well into the future. HEAT TREATMENT PLASTICS AND RUBBER AEROSPACE AND AUTOMOTIVE BRICKS AND CERAMICS FOOD, BREWING GLASS Ovens Furnaces Extrusion Injection molding Carburizing furnaces Tensile testing furnaces Creep testing furnaces Environmental chambers Autoclaves Stress relieving Hot presses Engine Test Beds Infra-red paint drying Driers Firing kilns Blending Baking Refrigeration Fermentation, Pasteurization Melting furnaces Forehearths Lehrs SEMICONDUCTOR Crystal growing Diffusion Molecular beam epitaxy CHEMICAL, PHARMACEUTICAL Reaction vessels Fermenters Pressure, flow, level, Ph UTILITIES, HEATING AND VENTILATION Gas burners and boiler control Trace heating Pressure reduction stations

3 PSG series 000 Iss5 0/5/00 :0 AM Page 3 00 Controller inx0.94in (48x4mm) inx.89in (48x48mm) Input General Range - to +80mV Sample rate 5Hz Calibration accuracy 0.5% of reading ± LSD or ± C/F Resolution < µv Linearization accuracy < 0.% of reading Input filter.0 to 999.9secs Zero offset User adjustable over the full display range Thermocouple Types J,K,T,L,N,C,R,S,B,Platinell ll (using ITS 90 temperature scale) Cold junction compensation Automatic compensation typically >5 to rejection of ambient temperature change External references: 3, 3, and F (0, 45, and 50 C) RTD Type -wire, Pt00 DIN43760 Process Range - to +80mV or 0 to 0mA (Configurable between limits) Supply voltage Standard Low voltage 85 to 64Vac -5%, +0%, 48 to 6Hz 0 to 9 Vac/dc Outputs Relay Rating: -pin relay Min: V, 00mA dc. Max: A, 64Vac resistive Heating, cooling or alarm Logic Rating 9Vdc, 8mA, non-isolated Heating, cooling, alarms or PDSIO mode : logic heating with load failure alarms Communications (not available on these units) Control Functions Control Modes PID or PI with overshoot inhibition, PD, P only, or On/Off Heating, cooling or heating plus cooling Setpoint rate limit Cooling algorithms 0.0 to degrees or display units per minute Linear only Tuning One-shot tune One-shot calculation of PID and overshoot inhibition parameters Auto. droop compensation Automatic calculation of manual reset value when using PD control Alarms Types Full scale high or low, deviation high, low, or band Modes Latching or non-latching with normal or blocking action Up to three process alarms can be combined onto a single output

4 PSG series 000 Iss5 0/5/00 :0 AM Page 4 00e Controller Motorized Valve Controller 6e 6e.89inx.89in (48x48mm) 08e 08e.89inx3.78in (48x96mm) 04e 04e 3.78inx3.78in (96x96mm) Inputs General Range ± 00mV and 0 to 0Vdc (auto ranging) Sample rate 9Hz (0mS) Calibration accuracy 0.5% of reading, ± LSD or ± C/F Resolution <µv for ± 00mV range, < 0.mV for 0Vdc range Linearization accuracy < 0.% of reading Input filter.0 to 999.9secs Zero offset User adjustable over full range Thermocouple Types J,K,T,L,N,C,R,S,B,Platinell ll (using ITS 90 temperature scale) Cold junction compensation Automatic compensation typically >30 to rejection of ambient temperature change External references 3, 3 and F (0, 45, and 50 C) RTD Type 3-wire, Pt00 DIN43760 Process Range ± 00mV, 0 to 0mA or 0 to 0Vdc (All configurable between limits) Type Linear Process value Digital Type Contact closure or 4Vdc logic input Manual select, nd setpoint, keylock, setpoint rate limit enable PDSIO Mode 5 Supply voltage 85 to 64Vac, 48 to 6Hz Outputs Relay Rating: -pin relays Min: V, 00mA dc. Max: A, 64Vac resistive Rating: change-over relay Min: 6V, ma dc. Max: A, 64Vac resistive Heating, cooling or alarms Logic Rating 8Vdc at 4mA (non-isolated) Heating, cooling, alarms or PDSIO mode : logic heating with load failure alarm PDSIO mode : Logic heating with load/ssc failure alarm and load current display Triac Rating A, 30 to 64Vac resistive Heating or cooling Analog Heating or cooling Isolated 0 to 0mA or 4 to0ma into 600Ω max Communications Digital Transmission standard EIA-485 at 00, 400, 4800, 9600 or 9,00 baud Protocol EI Bisynch, Modbus, DeviceNet PDSIO Setpoint input Setpoint input from master PDSIO controller. Holdback to master controller Control Functions Control Modes PID or PI with overshoot inhibition, PD, P only or On/Off Heating, cooling, heating plus cooling Auto/manual Bumpless transfer Setpoint rate limit 0.0 to degrees or display units per second, minute or hour Cooling algorithms Linear, water (evaporative), fan, oil, proportional only Tuning One-shot tune One-shot calculation of PID and overshoot inhibition parameters Auto. droop compensation Automatic calculation of manual reset value when using PD control Alarms Types Full scale high or low. Deviation high, low, or band Modes Latching or non-latching with normal or blocking action Up to four process alarms can be combined onto a single output

5 PSG series 000 Iss5 0/5/00 :0 AM Page Controller Setpoint Programmer Motorized Valve Controller inx.89in (48x48mm) inx3.78in (48x96mm) inx3.78in (96x96mm) Inputs General Range ± 00mV and 0 to 0Vdc (auto ranging) Sample rate 9Hz (0mS) Calibration accuracy 0.% of reading, ± LSD or ± C/F Resolution <µv for ± 00mV range, <0.mV for 0Vdc range Linearization accuracy No discernable error Zero drift with ambient temp. <0.µV per C for ± 00mV range, <0.mV per C on 0Vdc range Gain drift with ambient temp. <0.004% of reading per C Input filter.0 to 999.9secs Zero and span offset User adjustable over full display range Thermocouple Types J,K,T,L,N,C,R,S,B,Platinell ll (using ITS 90 temperature scale) Cold junction compensation Automatic compensation typically >30 to rejection of ambient temperature change External references: 3, 3, and F (0, 45, and 50 C) RTD Type 3-wire, Pt00 DIN43760 Process Range ± 00mV, 0 to 0mA or 0 to 0Vdc (All configurable between limits) Type Linear, square root or custom 8 point Process value Process value, remote setpoint, setpoint trim, power limit VP slidewire Range 00Ω to 000Ω Digital Type Contact closure or 4Vdc logic input Manual select, nd setpoint, nd PID, keylock, setpoint rate limit enable (PDSIO Mode 5) Program run, hold, reset, sync, fast run Supply voltage Standard 85 to 64Vac (code VH), 48 to 6Hz Low voltage 0 to 9 Vac/dc (code VL) Outputs Relay Rating: -pin relays Min: V, 00mA dc. Max: A, 64Vac resistive Min: V, 00mA dc. Max: A, 64Vac resistive (single and dual outputs) Rating: change-over relay Min: 6V, ma dc. Max: A, 64Vac resistive Heating, cooling, alarms or program event Logic Rating 8Vdc at 4mA, non-isolated 8Vdc at 4mA. Isolated and non-isolated versions available Heating, cooling, alarm, program event, PDSIO mode : Logic heating with load failure alarm Triple logic Rating Open collector, 50mA, 36Vdc max Triac Rating A, 30 to 64Vac resistive A, 30 to 64Vac resistive. Single and dual outputs Heating, cooling or program event Analog Heating or cooling or 0 to 0mA into 600Ω max or 0 to 0Vdc 0 to 0mA into 600Ω max, 0 to 0Vdc Isolated process output non-isolated (Configurable between limits) (Configurable between limits) Retransmission of PV or setpoint Isolated 0 to 0mA into 600Ω max, 0 to 0Vdc (Config. between limits) Transmitter supply 4Vdc, 0mA max Communications Digital Transmission standard EIA-3/4/485 at 00, 400, 4800, 9600 or 9,00 baud Protocol Modbus, EI Bisynch, ProfiBus (ProfiBus only available for 404 and 408) PDSIO Setpoint input Setpoint input from master PDSIO controller. Holdback to master controller Setpoint output Master setpoint retransmission to slave PDSIO controllers Control Functions Control Modes PID or PI with overshoot inhibition, PD, P only or On/Off Heating, cooling, heating plus cooling, and motorized valve positioning Auto/manual Bumpless transfer or forced manual output Setpoint rate limit 0.0 to degrees or display units per second, minute or hour Cooling algorithms Linear, water (evaporative), fan, oil, proportional only Tuning One-shot tune One-shot calculation of PID and overshoot inhibition parameters Adaptive Continuous assessment of the PID values Auto. droop compensation Automatic calculation of manual reset value when using PD control Alarms Types Full scale high or low. Deviation high, low, or band. Rate of change Modes Latching or non-latching with normal or blocking action Up to four process alarms. Any number of events can be combined onto a single output Setpoint Program size or 4 programs (6 segments), 4, or 0 progams (6 segments) Programming Event outputs Up to two Up to eight

6 3 6 6e 08e 04e PSG series 000 Iss5 0/5/00 :0 AM Page e 08e 04e INPUT STAGE Thermocouple Types Resistance Thermometer (PT00) Linear Millivolt / 4-0mA Input 0-0Vdc Custom Non-linear Curves HARDWARE FIXED Logic Output Relay Output Logic Input POWER SUPPLY High Voltage Supply Low Voltage Power Supply MODULAR COMMUNICATIONS MODULES PDSIO Setpoint Input PDSIO Setpoint Output Digital Communications CONTROL AND I/O MODULES Triac Relay Logic PDSIO Control Output DC Control (Analog Output) Dual Control - Triac + Triac Dual - Relay + Relay Transmitter Supply Triple Logic/Contact Input Triple Logic Output Valve Position Slidewire Feedback Analog Retransmission/Remote Setpoint High Current Switch Second Process Value Input

7 3 6 6e 08e 04e PSG series 000 Iss5 0/5/00 :0 AM Page e 08e 04e SOFTWARE FEATURES CONTROL PID Heat - Cool On/Off Heat - Cool Valve Positioner Valve Position Slidewire Feedback Self Tuning Adaptive Tuning Second PID Power Feedback Water, Fan and Oil Cooling SETPOINTS Setpoint Rate Limit Second Setpoint 6--Setpoint Unit PROGRAMMER or 4, 4, 0, 4, 0 Number of Programs Number of Segments max 8 max 8 max Event Outputs Run - Hold - Reset Logic Input BCD Program Select Holdback DIGITAL COMMUNICATIONS Modbus El Bisynch DeviceNet Profibus ALARM TYPES Full Scale High and Low Deviation High, Low and Band Rate of Change Loop Break Blocking Alarms Latching Alarms PDSIO FUNCTIONS SSRx Load Doctor SSRx Enhanced Load Doctor

8 PSG series 000 Iss5 0/5/00 :0 AM Page 8 INTERNATIONAL DISTRIBUTION AUSTRALIA Eurotherm Pty. Limited Hornsby New South Wales 077 AUSTRIA Eurotherm GmbH 0 Wien BELGIUM Eurotherm BV B 00 Deume (Antwerpen) DENMARK Eurotherm Danmark A/S DK 000 Frederiksberg FRANCE Eurotherm Automation SA Dardilly Cedex GERMANY Eurotherm Regler GmbH Limburg am der Lahn GREAT BRITAIN Eurotherm Controls Limited Worthing, West Sussex HONG KONG Eurotherm Limited Aberdeen JAPAN Eurotherm (Japan) Ltd. Tokyo 5 KOREA Eurotherm Korea Limited Seoul, NETHERLANDS Eurotherm BV 38 HJ Zoeterwoude NORWAY Eurotherm A/S N-4 Sofiemyr SPAIN Eurotherm España SA Madrid SWEDEN Eurotherm AB S-4 Malmö SWITZERLAND Eurotherm produkte (Schweiz) AG CH-85 Glattbrugg UNITED STATES OF AMERICA Eurotherm Controls Inc Reston, Virginia NEWS design & informatica ITALY Eurotherm SpA 070 Guanzate, Como Informações sobre programação soliton@soliton.com.br SOLITON CONTROLES INDUSTRIAIS LTDA Rua Alfredo Pujol, 00 - Santana - São Paulo - SP. Tel: / Fax: vendas@soliton.com.br HA056 Issue 5