Standard Rocking Platform WT15 Code No , Manual August 2004

Transcription

1 Standard Rocking Platform WT15 Code No , Manual August 2004!! Warning!! Please read these instructions carefully before using this apparatus! Biometra GmbH Rudolf-Wissell-Str. 30 D Göttingen Service Department Postfach 1544 Rudolf-Wissell-Str D Göttingen D Göttingen Tel: ++49 (0)5 51 / Tel.: ++49 (0)5 51 / or -12 Fax: ++49 (0)5 51 / Fax.: ++49 (0)5 51 / biometra.info@whatman.com biometra.service@whatman.com internet: Intended Uses And Specifications

2 Unpack the Standard Rocking Platform Table WT15 carefully. Examine for signs of damage and check the contents against the packing list. Notify BIOMETRA or your local BIOMETRA distributor immediately if you discover any damage or item discrepancies. Save all packing material if damage is found. Do not attempt to operate this device if physical damage is present. Read the complete instruction manual thoroughly and make sure that every user of the mixer/shaker has also read the instructions thoroughly before putting the equipment into operation. Keep the instruction manual where it can be consulted by all users. If, after reading the instruction manual, you still have any questions concerning the installation, operation or maintenance of the mixer/shaker, please contact BIOMETRA or your local BIOMETRA distributor. 2.0 Packing List The following individual and accessory part are supplied. Compare the contents of the shipment gbefore discarding the packing materials. We recommend keeping the original packing for future transport or storage purposes. Item Satndard Rocking Platform WT15 1 Instruction manual 1 Power cable 1 Quantity 2

3 3.0 Specifications Unit size: Unit weight: Platform size: Maximum load: Rocking frequency: 400 mm (w) x 350 mm (d) x 175 mm (h) 10 kg 350 x 400 mm 10 kg 4-40 cycles/min Shaking angle: 5 (optional 10 ) Temperature Range: ambient up to 50 C suitable for use in CO 2 and other incubators Main Voltage: Power Consumption: 230 Volt, 50 Hz 115 Volt, 60 Hz 50 Watts 3

4 4.0 Safety Instructions Before you connect up the power cable to the mains supply, check that: the voltage and frequency of the mixer/shaker conforms with the line voltage (the voltage rating of your mixer/shaker is printed on the nameplate). the power switch is set to "0" and the control knobs have all been turned counterclockwise up to the stop. This will prevent spills due to sudden, overly vigorous shaking. The mixer/shaker is not protected for use in explosive atmospheres. Be careful when using it close to flammable and explosive substances. The laboratory table must be strong and have a flat and non-slip surface. Before you start up the mixer/shaker, make sure that the vessel (process medium) is secure and cannot slip. Take precautions to prevent attachments or vessels colliding with other objects on the laboratory table during the shaking operation. To guard against splashing and spills, close the shaking vessels carefully. When you work with open vessels, select the shaking frequency accordingly. To prevent unintentional violent shaking, it is always advisable to start with a low shaking frequency and to increase it gradually in small steps until you reach the shaking effect you want. Always place single vessels at the centre of the platform. When working with several vessels, always distributed them evenly over the platform. Consult the load curves whenever you work with high loads and high shaking frequencies. Observe the pertinent safety regulations when working with hazardous media. Make allowance for the angle of inclination when using tall vessels. 4

5 5.0 Installation in the Laboratory Use the supplied power cable to connect the mixer/shaker to the mains supply. The appliance connector socket is at the rear. The mixer/shaker is protected by bipolar fuses. The fuses are located in the housing of the appliance connector socket and can be reached from the outside. The fuse rating is printed on the plate. For a description of how to operate your mixer/shaker, turn to the section "7.0 Operating the mixers/shakers" and look up your particular model variant. When working with low shaking frequencies, you can place flat vessels, e.g. Petri dishes, on the platform without an additional fixture. This mixer/shaker is fitted as standard with a EURO plug. For North America it comes with a US standard plug. To connect the mixer/shaker to a different mains system, you must use an authorized adapter or you must have an electrician replace the supplied plug with a suitable 3-pin plug authorized for your mains system. In its delivered condition the mixer/shaker is earthed! If you replace the original plug, make sure that the protective earth conductor of your mixer/shaker is connected to the new plug. 5

6 6.0 Assembly and Description All BIOMETRA models of the rocking and tumbling tables are stable and rugged shakers and mixers for maximum performance. They have been developed specially for the shaking and mixing of substances for scientific purposes in laboratories. Control knobs are neatly arranged at the front for convenient operation. With the delivered models there are no shaking frequency limits provided if they are loaded centrally as recommended. The Tumbling Table WT12 is used for the shaking of vessels - particularly flasks, bottles and dye pans - with a gentle asymmetrical motion. Vessels are placed on the rubber pad that is supplied with the mixer/shaker. The rubber pad is easy to replace. Shaking frequency is adjustable from 4 to 40 cycles/min. The angle of inclination is 5 or optional Operation The following controls are situated on the front panel from right to left 2-pole power switch with green illuminated rocker (1/0) Speed control knob (Speed) Use the power switch to turn the mixer/shaker on. Use the speed control knob to set the shaking frequency you require. 6

7 8.0 Dismantling, Transportation and Storage DISMANTLING 1. Switch off the mixer/shaker and remove the plug from the socket-outlet. 2. Remove all items of equipment from the vicinity of the mixer/shaker so that it can be dismantled without difficulty. 3. Remove all vessels from the mixer/shaker. Dismantle any accessories. TRANSPORTATION AND STORAGE To prevent damage, it is best to store and transport the mixer/shaker and its components in their original packaging or other suitable container. Close the packaging with adhesive tape. Store the mixer/shaker in a dry place. CAUTION: Guard the instrument from impact and vibration during transport. 9.0 Routine Cleaning and Maintenance Clean the housing and surface of the mixer/shaker with a damp cloth (mild suds). IMPORTANT: Never clean the mixer/shaker with chlorine bleach, detergents based on chlorine, scouring powder, ammonium, cleaning wool or agents with metallic constituents. This would cause damage to the sensitive surface of the equipment. The mixer/shaker has no wearing parts and requires no maintenance. If your BIOMETRA product ever needs to be repaired, you should enlist the services of a specialist who has been authorized by BIOMETRA to carry out such work. Contact your local BIOMETRA dealer or get in direct touch with BIOMETRA. 7

8 10.0 Service Should you have any problems with this unit, please contact our service department or your local Biometra dealer: Biometra GmbH Service Department Rudolf-Wissell-Straße D Göttingen Phone:++49 (0)5 51 / or 12 Fax: ++49 (0)5 51 / biometra.service@whatman.com If you would like to send the unit back to us, please read the following return instructions. Instructions for return shipment Return only defective devices. For technical problems which are not definitively recognisable as device faults please contact the Technical Service Department at Biometra. Use the original box or a similarly sturdy one. Label the outside of the box with CAUTION! SENSITIVE INSTRUMENT! Please enclose a precise description of the fault, which also reveals during which procedures the fault occurred, if possible. Important: Clean all parts of the instrument from residues, and of biologically dangerous, chemical and radioactive contaminants. Please include a written confirmation that the device is free of biologically dangerous and radioactive contaminants in each shipment. If the device is contaminated, it is possible that Biometra will be forced to refuse to accept the device. The sender of the repair order will be held liable for possible losses resulting from insufficient decontamination of the device. Please enclose a note which contains the following: a) Sender s name and address, b) Name of a contact person for further inquiries with telephone number. 8

9 Equipment Decontamination Certificate To enable us to comply with german law (i.e. 71 StrlSchV, 17 GefStoffV and 19 ChemG) and to avoid exposure to hazardous materials during handling or repair, will you please complete this form, prior to the equipment leaving your laboratory COMPANY / INSTITUTE ADDRESS TEL NO FAX NO EQUIPMENT Model Serial No If on loan / evaluation Start Date: Finish Date Hazardous materials used with this equipment Method of cleaning / decontamination The equipment has been cleaned and decontaminated: NAME POSITION (HEAD OF DIV./ DEP./ INSTITUTE / COMPANY) SIGNED DATE PLEASE RETURN THIS FORM TO BIOMETRA GMBH OR YOUR LOCAL BIOMETRA DISTRIBUTOR TOGETHER WITH THE EQUIPMENT. PLEASE ATTACH THIS CERTIFICATE OUTSIDE THE PACKAGING. INSTRUMENTS WITHOUT THIS CERTIFICATE ATTACHED WILL BE RETURNED TO SENDER. 9

10 11.0 Notes 10

11 EU - Konformitätserklärung EC - Declaration of Conformity Göttingen, den im Sinne der EG-Richtlinie über elektrische Betriebsmittel zur Verwendung innerhalb bestimmter Spannungsgrenzen 73/23/EWG following the EC directive about electrical equipment for use within certain limits of voltage 73/23/EEC und / and im Sinne der EG-Richtlinie für die elektromagnetische Verträglichkeit 89/336/EWG. following the EC directive about the electromagnetic compatibility 89/336/EEC. Hiermit erklären wir, daß folgender Wipptisch, Herewith we declare that the following Rocking Platform, Typ: type: Best.-Nr. / Order No , Standard-Wipptisch WT15 Standard Rocking Platform WT15 den grundlegenden Anforderungen der corresponds to the basic requirements of EG-Niederspannungsrichtlinie 73/23/EWG und der EC low voltage directive 73/23/EEC and the EG-Richtlinie über die elektromagnetische Verträglichkeit 89/336/EWG entsprechen. EC directive about the electromagnetic compatibility 89/336/EEC. Folgende harmonisierte Normen wurden angewandt: The following harmonized standards have been used: EN 55011: A1: A2:2000 EN :2000 EN : A1:2001 EN :2001 EN : Dr. Jürgen Otte Quality Manager Formular 006, Ver

12 Warranty This laboratory instrument is produced with the highest practical standards of materials, workmanship, and design. The design and manufacture of parts have been conceived with one purpose - to produce units which will give satisfactory service. Biometra GmbH guarantees this unit to be free from defects in materials or workmanship under normal use or service for 24 month from date of shipment. If, during this time, this unit proves defective in materials or workmanship, Biometra GmbH will repair or replace it free of charge if returned to us prepaid. This guarantee does not cover damage in transit, damage caused by carelessness, misuse or neglect, or unsatisfactory performance as a result of conditions beyond our control; or consequential losses as a result of failure of our product. Biometra GmbH Rudolf-Wissell-Str. 30 D Göttingen Service Department Postfach 1544 Rudolf-Wissell-Str D Göttingen D Göttingen Tel: ++49 (0)5 51 / Tel.: ++49 (0)5 51 / or -12 Fax: ++49 (0)5 51 / Fax.: ++49 (0)5 51 / biometra.info@whatman.com biometra.service@whatman.com internet: