LSI/CSI LS BIT MULTI-MODE COUNTER

Size: px

Start display at page:

Download "LSI/CSI LS BIT MULTI-MODE COUNTER"

Ashlynn Lyons
6 years ago
Views:

1 LSI/CSI LS766 UL LSI Computer Systems, Inc. 235 Walt Whitman Road, Melville, NY 747 (63) 27-4 FAX (63) A38 24-BIT MULTI-MODE COUNTER December 999 FEATURES: Programmable modes are: Up/Down, Binary, BCD, 24 Hour Clock, Divide-by-N, X or X2 or X4 Quadrature and Single Cycle. DC to 2 MHz Count Frequency. 8-Bit I/O Bus for Microprocessor Communication and Control. 24-Bit comparator for pre-set count comparison. Readable status register. Input/Output TTL and CMOS compatible. 5 V operation. 2-Pin Plastic DIP, 2-Pin SOIC GENERAL DESCRIPTION: The LS766 is a monolithic, CMOS Silicon Gate, 24-bit counter that can be programmed to operate in several different modes. The operating mode is set up by writing control words into internal control registers (see Figure 8). There are three 6-bit and one 2-bit control registers for setting up the circuit functional characteristics. In addition to the control registers, there is a 5-bit output status register (OSR) that indicates the current counter status. The LS766 communicates with external circuits through an 8-bit three state I/O bus. Control and data words are written into the LS766 through the bus. In addition to the I/O bus, there are a number of discrete inputs and outputs to facilitate instantaneous hardware based control functions and instantaneous status indication. PIN ASSIGNMENT - TOP VIEW (Write Input) (Chip Select Input) CS (Load Counter/Load Latch) LCTR/LLTC (A, B Gate/Reset Counter)ABGT/RCTR VDD (+5V) (Count Input) A (Count Input) B D D D LSI LS766 FIGURE VSS (GND) (Read Input) (Control/ Data Input) BW (Borrow Output) CY (Carry Output) D7 D6 D5 D4 D3 REGISTER DESCRIPTION: Internal hardware registers are accessible through the I/O bus () for READ or ITE when CS =. The input selects between the control registers ( = ) and the data registers ( = ) during a READ or ITE operation. (See Table ) The information included herein is believed to be accurate and reliable. However, LSI Computer Systems, Inc. assumes no responsibilities for inaccuracies, nor for any infringements of patent rights of others which may result from its use

2 PR (Preset register). The PR is the input port for the CNTR. The CNTR is loaded with a 24 bit data via the PR. The data is first written into the PR in 3 ITE cycle sequence of Byte (PR), Byte (PR) and Byte 2 (PR2). The address pointer for PR/PR/PR2 is automatically incremented with each write cycle. Accessed by: ITE when =, CS =. Bit # PR2 PR PR (BYTE 2) (BYTE ) (BYTE ) Standard Sequence for Loading PR and Reading CNTR: MCR ; Reset PR address pointer ITE PR ; Load Byte and into PR increment address ITE PR ; Load Byte and into PR increment address ITE PR ; Load Byte 2 and into PR3 increment address 8 MCR ; Transfer PR to CNTR MCR (Master Control Register). Performs register reset and load operations. Writing a "non-zero word to MCR does not require a follow-up write of an all-zero word to terminate a designated operation. Accessed by: ITE when =, CS =. Bit # : Reset PR/OL address pointer : Transfer CNTR to OL (24 bits) : Reset CNTR, BWT and CYT. Set SIGN bit. (CNTR=, BWT=, CYT=, SIGN=) : Transfer PR to CNTR (24 bits) : Reset COMPT (COMPT = ) : Master reset. Reset CNTR, ICR, OCCR, QR, BWT, CYT, OL COMPT, and PR/OL address pointer. Set PR (PR=FFFFFF) and SIGN. : Select MCR : NOTE: Control functions may be combined. ICR (Input Control Register). Initializes counter input operating modes. Accessed by: ITE when =, CS =. Bit # : Input A = Up count input, Input B = Down count input : Input A = Count input, Input B = Count direction input (overridden in quadrature mode) where B = selects up count mode and B = selects Down count mode. (NOTE: During counting operation B may switch only when A =.) : NOP : Increment CNTR once (A/B =, if enabled) : NOP : Decrement CNTR once (A/B =, if enabled) : Disable inputs A/B : Enable inputs A/B : Initialize Pin 4 as CNTR Reset input (Pin 4 = RCTR) : Initialize Pin 4 as Enable/Disable gate for A/B inputs (Pin 4 = ABGT) : Initialize Pin 3 as CNTR load input (Pin 3 = LCTR) : Initialize Pin 3 as OL load input (Pin 3 = LLTC) : Select ICR : NOTE: Control functions may be combined.

3 TABLE - Register Addressing Modes D7 D6 CS COMMENT X X X X X Disable Chip for READ/ITE Write to Master Control Register (MCR) Write to input control register (ICR) Write to output/counter control register (OCCR) Write to quadrature register (QR) X X Write to preset register (PR) and increment register address counter. X X Read output latch (OL) and increment register address counter X X Read output status register (OSR). X = Don't Care OSR (Output Status Register). Indicates CNTR status: Accessed by: READ when =, CS =. Bit # U U U / / / / / U = Undefined BWT. Borrow Toggle Flip-Flop. Toggles everytime CNTR underflows generating a borrow. CYT. Carry Toggle Flip-Flop. Toggles everytime CNTR overflows generating a carry. COMPT. Compare Toggle Flip-Flop. Toggles everytime CNTR equals PR SIGN. Sign bit. Reset ( = ) when CNTR underflows Set ( = ) when CNTR overflows UP/DOWN. Count direction indicatior in quadrature mode. Reset ( = ) when counting down Set ( = ) when counting up (Forced to in non-quadrature mode) OL(Output latch). The OL is the output port for the CNTR. The 24 bit CNTR Value at any instant can be accessed by performing a CNTR to OL transfer and then reading the OL in 3 READ cycle sequence of Byte (OL), Byte (OL) and Byte 2 (OL2). The address pointer for OL/OL/OL2 is automatically incremented with each READ cycle. Accessed by: READ when =, CS =. Bit # OL2 OL OL (BYTE 2) (BYTE ) (BYTE ) Standard Sequence for Loading and Reading OL: 3 MCR ; Reset OL address pointer and Transfer CNTR to OL READ OL ; Read Byte and increment address READ OL ; Read Byte and increment address READ OL ; Read Byte 2 and increment address

4 OCCR (Output Control Register) Initializes CNTR and output operating modes. Accessed by : ITE when =, CS =. Bit # : Binary count mode (Overridden by D3 = ). : BCD count mode (Overridden by D3 = ) : Normal count mode : Non-Recycle count mode. (CNTR enabled with a Load or Reset CNTR and disabled with generation of Carry or Borrow. In this mode no external CY or BW is generated. Instead CYT or BWT should be used as cycle completion indicator.) : Normal count mode : Divide by N count mode (CNTR is reloaded with PR data upon Carry or Borrow). : Binary or BCD count mode (see D) : 24 Hour Clock mode with Byte = Sec, Byte = Min and Byte 2 = Hr. (Overrides BCD/Binary Modes) Pin 6 = CY, Pin 7 = BW. (Active Low) Pin 6 = CYT, Pin 7 = BWT Pin 6 = CY, Pin 7 = BW. (Active high) Pin 6 = COMP, Pin 7 = COMPT Select OCCR QR (Quadrature Register). Selects quadrature count mode (See Fig. 7) Accessed by: ITE when =, CS =. Bit # X X X X X = Don t Care Disable quadrature mode Enable X quadrature mode Enable X2 quadrature mode Enable X4 quadrature mode Select QR

5 I/O DESCRIPTION: (See REGISTER DESCRIPTION for I/O Prgramming.) Data-Bus (D-D7) (Pin 8-Pin 5). The 8-line data bus is a threestate I/O bus for interfacing with the system bus. CS (Chip Select Input) (Pin 2). A logical at this input enables the chip for Read and Write. (Read Input) (Pin 9). A logical at this input enables the OSR and the OL to be read on the data bus. (Write Input) ( Pin ). A logical at this input enables the data bus to be written into the control and data registers. (Control/Data Input) ( Pin 8). A logical at this input enables a control word to be written into one of the four control registers or the OSR to be read on the I/O bus. A logical enables a data word to be written into the PR, or the OL to be read on the I/O bus. A (Pin 6). Input A is a programmable count input capable of functioning in three different modes, such as up count input, down count input and quadrature input. B (Pin 7). Input B is also a programmable count input that can be programmed to function either as down count input, or count direction control gate for input A, or quadrature input. When B is programmed as count direction control gate, B = enables A as the Up Count input and B = enables A as the Down Count input. When programmed as the direction input, B can switch state only when A is high. ABGT/RCTR ( Pin4). This input can be programmed to function as either inputs A and B enable gate or as external counter reset input. A logical is the active level on this input. In non-quadrature mode, if Pin 4 is programmed as A and B enable gate input, it may switch state only when A is high (if A is clock and B is direction) or when both A and B are high (if A and B are clocks). In quadrature mode, if Pin 4 is programmed as A and B enable gate, it may switch state only when either A or B switches. LCTR/LLTC ( Pin 3). This input can be programmed to function as the external load command input for either the CNTR or the OL. When programmed as counter load input, the counter is loaded with the data contained in the PR. When programmed as the OL load input, the OL is loaded with data contained in the CNTR. A logical is the active level on this input. CY (Pin6). This output can be programmed to serve as one of the following: A. CY. Complemented Carry out (active ). B. CY. True Carry out (active ). C. CYT. Carry Toggle flip-flop out. D. COMP. Comparator out (active ) BW (Pin7). This output can be programmed to serve as one of the following: A. BW. Complemented Borrow out (active ). B. BW. True Borrow out (active ). C. BWT. Borrow Toggle flip-flop out. D. COMPT. Comparator Toggle output. VDD (Pin 5). Supply voltage positive terminal. VSS (Pin 2). Supply voltage negative terminal. Absolute Maximum Ratings: Parameter Symbol Values Unit Voltage at any input VIN VSS-.3 to VDD+.3 V Operating Temperature TA to +7 oc Storage Temperature TSTG -65 to +5 oc Supply Voltage VDD-VSS +7. V DC Electrical Characteristics. (All voltages referenced to VSS. TA = to 7 C, VDD = 4.5V to 5.5V, fc =, unless otherwise specified) Parameter Symbol Min. Value Max.Value Unit Remarks Supply Voltage VDD V - Supply Current IDD - 35 µa Outputs open Input Low Voltage VIL.8 V - Input High Voltage VIH 2. VDD V - Output Low Voltage VOL -.4 V 4mA Sink Output High Voltage VOH V 2µA Source Input Current na Leakage Current Output Source Current ISRC 2 - µa VOH = 2.5V Output Sink Current ISINK 4 - ma VOL =.4V Data Bus Off-State Leakage Current na

6 - TRANSIENT CHARACTERISTICS (See Timing Diagrams in Fig. 2 thru Fig. 7, VDD = 4.5V to 5.5V, TA = to 7 C, unless otherwise specified) Parameter Symbol Min.Value Max.Value Unit Clock A/B low TCL 2 No Limit ns Clock A/B high TCH 3 No Limit ns Clock A/B Frequency fc 2 MHz (See NOTE ) Clock UP/DN Reversal TUDD - ns Delay LCTR Positive edge to TLC - ns the next A/B positive or negative edge delay Clock A/B to TCBL - 65 ns CY/BW/COMP low propagation delay Clock A/B t TCBH - 85 ns CY/BW/COMP high propagation delay LCTR and LLTC pulse TLCW 6 - ns width Clock A/B to CYT, BWT TTFH - ns and COMPT high propagation delay Clock A/B to CYT, BWT TTFL - ns and COMPT low progagation delay pulse width TWW 6 - ns to data out delay TR - ns (CL=2pF) CS, Terminate to TRT - 3 ns Data-Bus Tri-State Data-Bus set-up TDS 5 - ns time for Data-Bus hold time for TDH 3 - ns,cs set-up time for TCRS - ns, CS hold time for TCRH - ns set-up time for TCWS 5 - ns hold time for TCWH 3 - ns CS set-up time for TSWS 5 - ns CS holdtime for TSWH - ns Quadrature Mode: Clock A/B Validation delay TCQV - 6 ns (See NOTE 2) A and B phase delay TPH 28 - ns Clock A/B frequency fcq -.2 MHz CY,BW,COMP pulse width TCBW 75 8 ns NOTE : A) In Divide-by-N mode, the maximum clock frequency is MHz. B) The maximum frequency for valid CY, BW, CYT, BWT, COMP, COMPT is MHz. NOTE 2: In quadrature mode A/B inputs are filtered and required to be stable for at least TCQV length to be valid.

7 LTCR TLCW UP CLK (A) TLC TCL DN CLK (B) TCH TUDD TCH TCL Q Q Q2-Q23 CNTR=FFFFFD (PR=CNTR) CNTR=FFFFFE CNTR=FFFFFF CNTR= CNTR= CNTR= CNTR=FFFFFF CNTR=FFFFFE CNTR=FFFFFD (PR=CNTR) COMP NOTE 2 CY BW FIGURE 2. LOAD COUNTER, UP CLOCK, DOWN CLOCK, COMPARE OUT, CARRY, BORROW NOTE : The counter in this example is assumed to be operating in the binary mode. NOTE 2: No COMP output is generated here, although PR=CNTR. COMP output is disabled with a counter load command and enabled with the rising edge of the next clock, thus eliminating invalid COMP outputs whenever the CNTR is loaded from the PR. NOTE 3: When UP Clock is active, the DN Clock should be held high, and vice versa UP CLK OR DN CLK CY TCBL TCBH TTFH TTFL CYT BW TCBL TCBH TTFH TTFL BWT COMP TCBL TCBH TTFH TTFL COMPT SIGN (INTERNAL) FIGURE 3. CLOCK TO CY/BW OUTPUT PROPAGATION DELAYS

8 CS, TCRS TCRH DATA BUS T VALID OUTPUT TRT CS, TCWS TWW TCWH TSWS TSWH TDS TDH DATA BUS VALID DATA FIGURE 4. READ/ITE CYCLES LCTR DN CLK Q (INTERNAL) Q (INTERNAL) Q2-Q23 (INTERNAL) CNTR=3 =2 = = =3 =2 = = =3 CNTR LD (INTERNAL) BW NOTE: EXAMPLE OF DIVIDE BY 4 IN DOWN COUNT MODE FIGURE 5. DIVIDE BY N MODE CNTR LOAD (LCTR or MCR BASED) UP CLK OR DN CLK CY or BW CNTR DISABLED CNTR ENABLED CNTR DISABLED FIGURE 6. CYCLE ONCE MODE

9 FORWA REVERSE A B UPCLK (X) DNCLK (X) TPH TPH TCQV UPCLK (X2) DNCLK (X2 UPCLK (X4) TCQV DNCLK (X4) UP/DN(OSR Bit 4) CY TCBW BW TCBW FIGURE 7. QUADRATURE MODE INTERNAL CLOCKS

10 (DATA-BUS) 8-5 I/O BUFFER D -D4 OSR (CHIP SELECT INPUT) CS 2 D, D6,D7 QR (READ INPUT) (ITE INPUT) (CONTROL /DATA INPUT) (COUNT INPUT) A (COUNT INPUT) B (AB GATE/LOAD LATCH) ABGT/RCTR INPUT BUFFER AND LOGIC INTERNAL DATA BUS OCCR ICR MCR CONTROL LOGIC STATUS LOGIC 6 7 CY (CARRY OUT) BW (BORROW OUT) (LOAD CTR/LOAD LATCH) LCTR/LLTC 3 COMPARATOR N=N2 N N2 PR/OL ADDRESS (+5V) VDD (GND) VSS 5 2 D -D7 PR B - B7 PR B8 - B5 PR2 B - B23 CNTR Q -Q23 OL OL B6 - B23 OL2 FIGURE 8. LS766 BLOCK DIAGRAM PR/OL ADDRESS UP CLOCK DN CLOCK

11 LS766 INTERFACE EXAMPLESS ADDRESS BUS CS A DATA BUS DBIN ADRS/ DATA DATA ADDRESS ALE STB 8282 CS 766 S - S2 I/O A 886/888 (Minimum Mode) CLK +V S D S74 CK R Q S -S2 IORC 8288 IOWC ALE 886/888 (Maximum Mode) ADRS/DATA STB 8282 ADDRESS CS 766 DATA A

12 LS766 INTERFACE EXAMPLES ADDRESS BUS A IORQ CS 766 Z8 DATA BUS ADRS/ DATA D Q LS373 DATA A ADDRESS AS ST-ST3 Z8 CK I/O CS 766 R/W DS ADDRESS D Q LS373 CK DATA BUS A CS R/W LDS/UDS +V S D S74 CK Q R +V 766 AS DTACK CLK CLOCK S D S74 Q CK R Q S D S74 CK R

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) BIT QUADRATURE COUNTER

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) BIT QUADRATURE COUNTER LSI/CSI LS UL LSI Computer Systems, Inc. Walt Whitman Road, Melville, NY () - FAX () - A -BIT QUADRATURE COUNTER January FEATURES: Programmable modes are: Up/Down, Binary, BCD, Hour Clock, Divide-by-N,