SigmaLogic7 Compact Hardware Manual

Transcription

1 SigmaLogic7 Compact Hardware Manual

2

3 Table of Contents Table of Contents Introduction. SigmaLogic7 Compact Features SigmaLogic7 Compact Appearance Model Number Designation Accessories Specifications and Settings. Specifications DIP Switch Settings Rotary Switches Switch Factory Settings Installation Standards 3. Mechanical Installation/Dimensions Installing Multiple SERVOPACKS in a Control Panel Inputs and Outputs 4. Input Signals Output Signals I/O Signal Connector (CN) Pin Arrangement I/O Signal Wiring Examples I/O Circuits LED Outputs Ethernet Connectivity 6. Ethernet Connector Details Ethernet Cable Ethernet Connection Examples

4 Table of Contents 7 Cable Diagrams 7. SBK-U-VBA-xx JZSP-CSI0-x-E EMC Installation Conditions

5 Introduction Introduction. SigmaLogic7 Compact Features The SigmaLogic7 Compact is a Sigma-7 SERVOPACK that features built-in functionality which can be accessed by a Rockwell PLC using EtherNet/IP protocol. Product features include: Easy configuration with Yaskawa's free LogicWorks software Add On Instructions (AOIs) are provided for use with Rockwell RSLogix 5000 software Ethernet (00Mbps) auto crossover switching EtherNet/IP Allow high-speed communications with PLC Sigma-7 servo amplifier I/O features 7 digital inputs 3 digital outputs 3

6 Introduction. SigmaLogic7 Compact Appearance The following figure shows the external appearance of the SigmaLogic7 Compact servo interface. Switches (under cover) Main Circuit Power Supply Control Circuit Power Supply Regenerative Resistor Connections Servo Motor Power LED Indicators CN6A/B: Ethernet CN7: USB CN: SERVOPACK I/O CN8: HWBB CN: Encoder 4

7 Introduction.3 Model Number Designation SGD7S - Σ-7 Series SERVOPACK R8 A Q0 A 000 F5 st+nd+3rd digits 4th digit 5th+6th digits 7th digit 8th+9th+0th digits th+th+ 3th digits st+nd+3rd digits Maximum Applicable Motor Capacity Voltage Code Specification Threephase, R70 * R90 * R6 * R8 * 3R8 5R5 * 7R kw 0. kw 0. kw 0.4 kw 0.5 kw 0.75 kw.0 kw.5 kw kw VAC kw Singlephase, 00 VAC R70 R90 R R8 5.0 kw 6.0 kw 7.5 kw kw 5 kw 0.05 kw 0. kw 0. kw 0.4 kw 4th digit Voltage Code Specification A 00 VAC F 00 VAC 5th+6th digits Interface Code Q0 Specification SigmaLogic7 Compact 7th digit Design Revision Order A: Global design revision 8th+9th+0th digits Code 000 Specification Without options th+th+3th digits Hardware Options Specification Applicable Models All models FT/EX Specification Code Specification F5 Application function for SigmaLogic7 *: These models can be used with either a single-phase or three-phase power supply input.4 Accessories System Components Type Description Model Number Note Accessories and Cables Communication CN Terminal Block Conversion Kit CN Cable (Flying leads) Ethernet Cable SBK-U-MPBxx JZSP-CSI0-x-E Customer Supplied xx denotes cable length A5: 0.5 m 0:.0 m 03: 3.0 m x denotes cable length A:.0 m B:.0 m C: 3.0 m Use high quality shielded industrial Ethernet cables (Yaskawa model JZSP-CM3RRM0-xx-E is recommended) 5

8 Introduction 6

9 Specifications and Settings Specifications and Settings. Specifications Item Control Method Feedback With Rotary Servomotor With Linear Servomotor Surrounding Air Temperature Storage Temperature Surrounding Air Humidity Storage Humidity Specification IGBT-based PWM control, sine wave current drive Serial encoder: 0 bits or 4 bits (incremental encoder/ absolute encoder) bits (absolute encoder) Absolute linear encoder (The signal resolution depends on the absolute linear encoder.) Incremental linear encoder (The signal resolution depends on the incremental linear encoder or Serial Converter Unit.) -5 C to 55 C (With derating, usage is possible between 55 C and 60 C.) -0 C to 85 C Vibration Resistance 4.9 m/s Shock Resistance 9.6 m/s 95% relative humidity max. (with no freezing or condensation) 95% relative humidity max. (with no freezing or condensation) Environmental Conditions Degree of Protection Degree IP0 IP0 SERVOPACK Model: SGD7S- R70A, R90A, R6A, R8A, 3R8A, 5R5A, 7R6A, 0A, R70F, R90F, RF, R8F 80A, 00A, 330A, 470A, 550A, 590A, 780A Pollution Degree Altitude Others Applicable Standards Must be no corrosive or flammable gases. Must be no exposure to water, oil, or chemicals. Must be no dust, salts, or iron dust.,000 m or less. (With derating, usage is possible between,000 m and,000 m.) Do not use the SERVOPACK in the following locations: Locations subject to static electricity noise, strong electromagnetic/magnetic fields, or radioactivity Compliance with UL Standards, EU Directives and Other Safety Standards Mounting Mounting Base-mounted Rack-mounted Duct-ventilated All Models SERVOPACK Model: SGD7S- R70A, R90A, R6A, R8A, 3R8A, 5R5A, 7R6A, 0A, 80A, 00A, 330A, R70F, R90F, RF, R8F 470A, 550A, 590A, 780A 7

10 Specifications and Settings Performance I/O Signals I/O Signals Item Speed Control Range Coefficient of Speed Fluctuation Torque Control Precision (Repeatability) Soft Start Time Setting Encoder Divided Pulse Output Linear Servomotor Overheat Protection Signal Input Digital Input Signals Digital Output Signals Input Signals That Can Be Allocated Fixed Output Output Signals That Can Be Allocated :5000 (At the rated torque, the lower limit of the speed control range must not cause the Servomotor to stop.) ±0.0% of rated speed max. (for a load fluctuation of 0% to 00%) 0% of rated speed max. (for a voltage fluctuation of ±0%) ±0.% of rated speed max. (for a temperature fluctuation of 5 C ±5 C) ±% Specification 0 s to 0 s (Can be set separately for acceleration and deceleration.) Phase A, phase B, phase C: Line-driver output Number of divided output pulses: Any setting is allowed. Number of input points: Input voltage range: 0 V to +5 V Allowable voltage range: 4 VDC ±0% Number of input points: 7 Input method: Sink inputs or source inputs Input Signals P-OT (Forward Drive Prohibit) and N-OT (Reverse Drive Prohibit) signals /EXT External latch signal input (General purpose input) /EXT (General Purpose Input) signal /EXT3 (General Purpose Input) signal /P-CL (Forward External Torque Limit) and /N-CL (Reverse External Torque Limit) signals FSTP (Forced Stop Input) signal A signal can be allocated and the positive and negative logic can be changed. Allowable voltage range: 5 VDC to 30 VDC Number of output points: Output signal: ALM (Servo Alarm) signal (cont?d) Allowable voltage range: 5 VDC to 30 VDC Number of output points: 3 (A photocoupler output (isolated) is used.) Output Signals /COIN (Positioning Completion) signal /V-CMP (Speed Coincidence Detection) signal /TGON (Rotation Detection) signal /S-RDY (Servo Ready) signal /CLT (Torque Limit Detection) signal /VLT (Speed Limit Detection) signal /BK (Brake) signal /WARN (Warning) signal /NEAR (Near) signal A signal can be allocated and the positive and negative logic can be changed. 8

11 Specifications and Settings Communications Displays/Indicators RS-4A Communications (CN50) USB Communications (CN7) Analog Monitor (CN5) Dynamic Brake (DB) Regenerative Processing Overtravel (OT) Prevention Protective Functions Utility Functions Safety Functions Item Inputs Output Applicable Standards Applicable Option Modules Interfaces :N Communications Axis Addres s Setting Interface Communications Standard A JUSP-JC00 Communications Unit is required to connect to a Digital Operator (JUSP-OP05A--E). Up to N = 5 stations possible for RS-4A port Set with parameters. Specification Personal computer (with SigmaWin+) Conforms to USB.0 standard ( Mbps). CHARGE, PWR, CN, RUN, ERR, and L/A (A and B) indicators, and one-digit seven-segment display Number of points: Output voltage range: ±0 VDC (effective linearity range: ±8 V) Resolution: 6 bits Accuracy: ±0 mv (Typ) Maximum output current: ±0 ma Settling time (±%):. ms (Typ) Activated when a servo alarm or overtravel (OT) occurs, or when the power supply to the main circuit or servo is OFF. Built-in (An external resistor must be connected to the SGD7S- 470A to -780A.) Refer to the following manual for details. S-7-Series AC Servo Drive Peripheral Device Selection Manual (Manual No.: SIEP S ) Stopping with dynamic brake, deceleration to a stop, or coasting to a stop for the P-OT (Forward Drive Prohibit) or N-OT (Reverse Drive Prohibit) signal Overcurrent, overvoltage, low voltage, overload, regeneration error, etc. Gain adjustment, alarm history, jogging, origin search, etc. /HWBB and /HWBB: Base block signals for Power Modules EDM: Monitors the status of built-in safety circuit (fixed output). ISO3849- PLe (Category 3), IEC6508 SIL3 (cont?d) Fully-closed Modules and Safety Modules Note: You cannot use a Fully-closed Module and a Safety Module together. 9

12 Specifications and Settings. DIP Switch Settings DIP Switches 3 4 Rotary Switches (used to set IP address) Rotary Switch Rotary Switch 0 Switch Name Setting Operating Mode Setting for Normal Operation Details STOP SUP 3 INIT 4 E-INIT ON OFF ON OFF ON OFF ON OFF User program execution inhibited OFF Inhibits user program execution Normal operation Firmware programming mode Normal operation Configuration bypass mode Normal operation Normal operation Rotary switches ignored OFF OFF OFF Enables servo controller firmware programming. This mode can also be performed via web UI without changing the DIP switch. Set to ON to bypass the stored configuration (e.g. in case of a configuration problem that prevents servo controller startup) Rotary switches used to set IP address IP address is set from configuration settings in servo controller 0

13 Specifications and Settings.3 Rotary Switches When DIP switch 4 (E-INIT) is OFF, the rotary switches are ignored. The IP address is set from configuration settings stored on the servo controller. Rotary switches are normally used to set the IP address. This is the case when DIP switch 4 (E-INIT) is ON If both rotary switches are set to 0, use DHCP. If either rotary switch is non zero, the last octet of the IP address is set by the value on the switches. Note that the switch values are labeled in hexadecimal. The IP address will be x where x is 0x0 to 0xFF for a decimal value of 0 to 55. Rotary Switch Rotary Switch 0 IP Address 0 0 Set by DHCP F F F F Switch Factory Settings All DIP switches off Rotary switches at 0 and. Configured IP address is

14 Specifications and Settings

15 3 Installation Standards 3 Installation Standards 3. Mechanical Installation/Dimensions The SigmaLogic7 Compact servo interface is based on the Sigma- 7S EtherCAT servo amplifier. As such, it has the same envelope and mechanical installation directions. Please refer to section.3 of the Sigma-7S EtherCAT (CoE) Communications Reference Product Manual (document number SIEPS ) 3

16 3 Installation Standards 3. Installing Multiple SERVOPACKS in a Control Panel Provide the following intervals between the SERVOPACKs and spaces around the SERVOPACKs. Important Install cooling fans above the SERVOPACKs so that hot spots do not occur around the SERVOPACKs. Provide sufficient intervals and spaces as shown in the following figure to enable cooling by the fans and natural convection. 40 mm min. Fan Fan 30 mm min. SERVOPACK SERVOPACK SERVOPACK SERVOPACK 30 mm min. This distance depends on the model. 40 mm min. The space required on the right side of a SERVOPACK (when looking at the SERVOPACK from the front) depends on the SERVOPACK models. Refer to the following table. SGD7S- SERVOPACK Model R70A, R90A, R6A, R8A, 3R8A, 5R5A, 7R6A, R70F, R90F, RF, R8F 0A, 80A, 00A, 330A, 470A, 550A, 590A, 780A Space on Right Side Cooling Fan Installation Conditions 0 mm above SERVO- PACK s Top Surface mm min. Air speed:.0 m/s min. 0 mm min. Air speed:.0 m/s min. 4

17 4 Inputs and Outputs 4 Inputs and Outputs 4. Input Signals Default settings are provided in parentheses Signal /SI (P-OT) /SI (N-OT) Pin No. 7 8 Name General-purpose Digital Input (Forward Drive Prohibit Input) General-purpose Digital Input (Reverse Drive Prohibit Input) /SI3 9 General-purpose Digital Input 3 /SI4 (/EXT) /SI5 (/EXT) /SI6 (/EXT3) 0 External latch signal input (General purpose input 4) General-purpose Digital Input 5 General-purpose Digital Input 6 /SI0 3 General-purpose Digital Input 0 +4VIN 6 Digital Input Signal Power Supply Input Function You can allocate the input signal to use with a parameter. (Stops Servomotor drive (to prevent overtravel) when the moving part of the machine exceeds the range of movement.) You can allocate the input signal to use with parameters. (Used for general-purpose input.) You can allocate the input signals to use with parameters. You can allocate the input signal to use with a parameter. (Used for general-purpose input.) Inputs the Digital Input signal power supply. Allowable voltage range: 4 VDC ±0% The 4-VDC power supply is not provided by Yaskawa. BAT+ 4 Battery for Absolute Encoder (+) These are the pins to connect the absolute encoder backup battery. BAT- 5 Battery for Absolute Encoder (-) Do not connect these pins if you use the Encoder Cable with a Battery Case. TH 5 Linear Servomotor Overheat Inputs the overheat protection signal from a Protection Input Linear Servomotor. Note: If forward drive prohibition or reverse drive prohibition is used, the SERVOPACK is stopped by software controls. If the application does not satisfy the safety requirements, add external safety circuits as required. 5

18 4 Inputs and Outputs 4. Output Signals Default settings are provided in parentheses. Signal Pin No. ALM+ 3 Name Servo Alarm Output ALM- 4 /SO+ (/BK+) General-purpose Digital Output (Brake Output) /SO- (/BK-) Function Turns OFF (opens) when an error is detected. You can allocate the output signal to use with a parameter. (Controls the brake. The brake is released when the signal turns ON (closes).) /SO+ /SO- 3 4 General-purpose Digital Output /SO3+ 5 General-purpose Digital /SO3-6 Output 3 PAO 7 Encoder Divided Used for general-purpose outputs. Set the parameters to allocate functions. Pulse Output, Phase A Output the encoder divided pulse output signals with a 90 phase differential. /PAO 8 PBO /PBO 9 0 Encoder Divided Pulse Output, Phase B PCO Encoder Divided /PCO Pulse Output, Phase Outputs the origin signal once every encoder rotation. C SG 6 Signal ground This is the 0-V signal for the control circuits. FG Shell Frame ground Connected to the frame ground if the shield of the I/O Signal Cable is connected to the connector shell. 6

19 4 Inputs and Outputs 4.3 I/O Signal Connector (CN) Pin Arrangement The following figure gives the pin arrangement of the of the I/O signal connector (CN) for the default settings. Pin Pin Pin Pin 3 Pin 4 Pin 5 Pin 5 Pin 6 The above view is from the direction of the following arrow without the connector shell attached. /SO- (/BK-) 4 ALM VI N /SI (N-OT) /SI4 (/EXT) /SI6 (/EXT3) Generalpurpose Digital Output Servo Alarm Output Digital Input Signal Power Supply Input Generalpurpose Digital Input External latch signal input (General purpose input 4) Generalpurpose Digital Input 6 /SO+ (/BK+) 3 ALM+ 5 TH 7 9 /SI (P-OT) /SI3 (/DEC) /SI5 (/EXT) 3 /SI0 Generalpurpose Digital Output Servo Alarm Output Linear Servomotor Overheat Protection Input Generalpurpose Digital Input Generalpurpose Digital Input 3 Generalpurpose Digital Input 5 Generalpurpose Digital Input 0 5 BAT- 7 PAO 9 PBO PCO 3 /SO+ 5 /SO3+ Battery for Absolute Encoder (-) Encoder Divided Pulse Output, Phase A Encoder Divided Pulse Output, Phase B Encoder Divided Pulse Output, Phase C Generalpurpose Digital Output Generalpurpose Digital Output 3 Battery for Absolute Encoder (+) Signal Ground Encoder Divided Pulse Output, Phase A Encoder Divided Pulse Output, Phase B Encoder Divided Pulse Output, Phase C 4 BAT+ 6 SG 8 /PAO 0 /PBO /PCO 4 /SO- 6 /SO3- Generalpurpose Digital Output Generalpurpose Digital Output 3 7

20 4 Inputs and Outputs 4.4. Using a Rotary Servo Motor 4.4 I/O Signal Wiring Examples 4.4. Using a Rotary Servo Motor CN SERVOPACK Photocoupler outputs Max. allowable voltage: 30 VDC Max. allowable current: 50 ma DC Digital input signal power supply input Forward Drive Prohibit input (prohibited when OFF) Reverse Drive Prohibit input (prohibited when OFF) General-purpose digital input 3 External latch signal input (General purpose input 4) General-purpose digital input 5 General-purpose digital input 6 General-purpose digital input 0 + Battery for - absolute encoder Backup battery *.8 V to 4.5 V *3 +4 V +4VIN kω * P-OT N-OT /SI3 /EXT /EXT /EXT /SI0 3 BAT+ 4 BAT- 5 3 ALM+ 4 ALM- /BK+ /BK- 3 /SO+ 4 /SO- 5 /SO3+ 6 /SO PAO /PAO PBO /PBO PCO /PCO 6 SG Servo Alarm Output (OFF for alarm) Brake output (released when ON) Signal ground *4 Encoder Divided Pulse Output, Phase A *4 Encoder Divided Pulse Output, Phase B *4 Encoder Divided Pulse Output, Phase C Applicable Line Receiver: SN75ALS75 or MC3486 manufactured by Texas Instruments or the equivalent Connector shell FG Connect shield to connector shell. Frame ground *. represents twisted-pair wires. *. Connect these when using an absolute encoder. If the Encoder Cable with a Battery Case is connected, do not connect a backup battery. * 3. The 4-VDC power supply is not provided by Yaskawa. Use a 4-VDC power supply with double insulation or reinforced insulation. * 4. Always use line receivers to receive the output signals. Note:. You can use parameters to change the functions allocated to the /SI0, /SI3, P-OT, N-OT, /EXT, /EXT, and /EXT3 input signals and the /SO, /SO, and /SO3 output signals.. If you use a 4-V brake, install a separate power supply for the 4-VDC power supply from other power supplies, such as the one for the I/O signals of the CN connector. If the power supply is shared, the I/O signals may malfunction. 8

21 4 Inputs and Outputs 4.4. Using a Linear Servo Motor 4.4. Using a Linear Servo Motor Linear Servomotor overheat protection input TH 5 Digital input signal +4 V * +4VIN 6 power supply input Forward Drive Prohibit input P-OT 7 (prohibited when OFF) Reverse Drive Prohibit input (prohibited when OFF) General-purpose digital input 3 External latch signal input (General purpose input 4) General-purpose digital input 5 General-purpose digital input 6 General-purpose digital input 0 N-OT /SI3 /EXT /EXT /EXT3 /SI0 CN kω SERVOPACK 3 4 ALM+ ALM /BK+ /BK- /SO+ /SO- /SO3+ 6 /SO3-7 PAO * 8 /PAO 9 0 PBO /PBO PCO /PCO Photocoupler outputs Max. allowable voltage: 30 VDC Max. allowable current: 50 ma DC Servo Alarm Output (OFF for alarm) Brake output (released when ON) *3 *3 *3 Encoder Divided Pulse Output, Phase A Encoder Divided Pulse Output, Phase B Encoder Divided Pulse Output, Phase C Applicable Line Receiver: SN75ALS75 or MC3486 manufactured by Texas Instruments or the equivalent 6 SG Connector shell FG Connect shield to connector shell. Frame ground *. represents twisted-pair wires. *. The 4-VDC power supply is not provided by Yaskawa. Use a 4-VDC power supply with double insulation or reinforced insulation. * 3. Always use line receivers to receive the output signals. Note:. You can use parameters to change the functions allocated to the /SI0, /SI3, P-OT, N-OT, /EXT, /EXT, and /EXT3 input signals and the /SO, /SO, and /SO3 output signals.. If you use a 4-V brake, install a separate power supply for the 4-VDC power supply from other power supplies, such as the one for the I/O signals of the CN connector. If the power supply is shared, the I/O signals may malfunction. 9

22 4 Inputs and Outputs 4.5. Digital Input Circuits 4.5 I/O Circuits 4.5. Digital Input Circuits Photocoupler Input Circuits This section describes CN connector terminals 6 to 3. Examples for Relay Circuits SERVOPACK 4 VDC +4VIN 4.7 kω e.g., /DEC Examples for Open-Collector Circuits 4 VDC +4VIN e.g., /DEC SERVOPACK 4.7 kω Note: The 4-VDC external power supply capacity must be 50 ma minimum. The SERVOPACK input circuits use bi-directional photocouplers. Select either a sink circuit or source circuit according to the specifications required by the machine. Note: The connection examples in 4.4 I/O Signal Wiring Examples are for sink circuit connections. Sink Circuits Source Circuits 4 V 4 V + SERVOPACK input side + SERVOPACK input side Switch Switch Photocoupler Photocoupler Internal signal level Internal signal level Switch Switch Photocoupler Photocoupler Internal signal level Internal signal level Input Signal Polarity Input Signal Polarity Photocoupler Internal Signal Internal Signal Photocoupler Level Level ON Low level ON Low level OFF High level OFF High level 0

23 4 Inputs and Outputs 4.5. Digital Output Circuits 4.5. Digital Output Circuits Important Incorrect wiring or incorrect voltage application to the output circuits may cause short-circuit failures. If a short-circuit failure occurs as a result of any of these causes, the holding brake will not work. This could damage the machine or cause an accident that may result in death or injury. Photocoupler Output Circuits Photocoupler output circuits are used for the ALM (Servo Alarm), /S-RDY (Servo Ready), and other digital output signals. Connect a photocoupler output circuit to a relay or line-receiver circuit. Example for Relay Circuit Example for Line-Receiver Circuit SERVOPACK 5 VDC to 30 VDC Relay SERVOPACK 5 VDC to 30 VDC 0V Note: The maximum allowable voltage and current range for photocoupler output circuits are as follows: Maximum allowable voltage: 30 VDC Current range: 5 ma to 50 ma DC Line-Driver Output Circuits This section describes CN connector terminals 7-8 (Phase-A Signal), 9-0 (Phase-B Signal), and - (Phase-C Signal). The serial data from the encoder is converted to two-phase (phases A and B) pulses. The resulting output signals (PAO, /PAO and PBO, /PBO) and origin pulse signal (PCO and /PCO) are output with line-driver output circuits. Connect the linedriver output circuits to line-receiver circuits at the host controller. Example for Line-Receiver Circuit SERVOPACK Output line driver: SN75ALS74 or the equivalent Host controller Applicable line receiver: SN75ALS75 or MC3486 manufactured by Texas Instruments or the equivalent 0 Ω to 470 Ω

24 4 Inputs and Outputs 4.5. Digital Output Circuits

25 5 LED Outputs 5 LED Outputs The following indicators show the operating status of the servo controller and error information. ERR: Solid at power up Off when there is no error Solid when there is an alarm Blinking when there is a critical error RUN: Solid when internal logic controller is booted and ready Blinking when internal logic controller is running a program Ethernet Link/Activity: Off when CN6A/B does not have an active Ethernet connection Solid when CN6A/B has an active Ethernet connection Blinking when CN6A/B is transmitting or receiving data 3

26 5 LED Outputs 4

27 6 Ethernet Connectivity 6 Ethernet Connectivity The SigmaLogic7 Compact supports both 00 Mbps/00Base-TX and 0 Mbps/0Base-T connections. One single network is accessed using both CN6A and CN6B. The same IP address is set for both ports. The Ethernet address (MAC address) can be found on the nameplate. 6. Ethernet Connector Details Ethernet Connector Specification and Pin Array The following table provides the Ethernet connector specifications. Connector Name Number of Pins Ethernet 8 Connector Model Module Side Cable Side Manufacturer RJ-45 CAT5 Socket RJ-45 CAT5 Plug TE Connectivity The following table provides Ethernet connector pin array details. Ethernet Pin Number Signal Name Description TXD+ Transmitted data + side TXD- Transmitted data side 3 RXD+ Received data + side RXD- Received data side 7 8 5

28 6 Ethernet Connectivity 6. Ethernet Cable For the Ethernet cable, use a twisted pair cable with RJ-45 connector. Yaskawa strongly recommends the use of shielded ethernet cables (Yaskawa model JZSP-CM3RRM0-xx-E). Ethernet ports are capable of auto-crossover, so crossover cables are not necessary. 6.3 Ethernet Connection Examples Connection Example (When using a Repeater Hub) SigmaLogic7 Compact SigmaLogic7 Compact Station Station 00Base-TX Up to 00m Up to 00m Up to 00m 00Base-TX Ethernet Switch Up to 00m 00Base-TX Ethernet Switch Up to 00m Up to 00m Station Station Specification Cable length from node to Ethernet hub or switch Cable length between Ethernet hubs or switches Number of Ethernet hubs or switches between nodes 00 m or less 00 m or less Unlimited 6

29 SigmaLogic7 Compact 6 Ethernet Connectivity Connection Example SigmaLogic7 Compact SigmaLogic7 Compact 00 Base-TX (up to 00m) Station Connection Example 3 SigmaLogic7 Compact Station Core 00Base-TX Core 00Base-TX Ethernet Switch Servo motor LogicWorks 7

30 6 Ethernet Connectivity Caution Electromagnetic interference (EMI) may interfere with Ethernet communication. The following measures can help minimize the influence of EMI:. Locate Ethernet cables so that they are well-separated from power cables or other sources of EMI. Yaskawa strongly recommends the use of high-quality shielded Ethernet cables such as JZSP-CM3RRM0-xx-E 3. Attach ferrite cores to Ethernet cables that are subjected to EMI Recommended ferrite core: Model E04SR30334 Manufacturer Seiwa Electric Mfg. Co., Ltd 8

31 7 Cable Diagrams 7 Cable Diagrams 7. SBK-U-VBA-xx Terminal Block - CN I/O. SBK-U-VBA-xx Function Chart for Sigma-5 or Sigma-7 Servo Amplifier Pin No. Mechatrolink-II type Servo Amplifier / Option type Signal Function /BK+ (/SO+) Brake interlock output (+) (General purpose output (+)) /BK- (/SO-) Brake interlock output (-) (General purpose output (-)) 3 ALM+ Servo alarm output (+) 4 ALM- Servo alarm output (-) VIN Control power supply for digital signal input 7 P-OT (/SI) Forward run prohibited input (General purpose input ) 8 N-OT (/SI) Reverse run prohibited input (General purpose input ) 9 /DEC (/SI3) Zero-point return deceleration switch input (General purpose input 3) 0 /EXT (/SI4) External latch signal input (General purpose input 4) /EXT (/SI5) External latch signal input (General purpose input 5) /EXT3 (/SI6) External latch signal 3 input (General purpose input 6) 3 /SI0 General purpose input 0 4 BAT (+) Battery (+) input 5 BAT (-) Battery (-) input 6 SG Signal ground 7 PAO Phase-A pulse output (+) 8 /PAO Phase-A pulse output (-) 9 PBO Phase-B pulse output (+) 0 /PBO Phase-B pulse output (-) PCO Phase-C pulse output (+) /PCO Phase-C pulse output (-) 3 /SO+ General purpose output (+) 4 /SO- General purpose output (-) 5 /SO3+ General purpose output 3 (+) 6 /SO3- General purpose output 3 (-) Note: General purpose input and output signals are shown with their default signals assigned - signal assignment may have been changed by parameter 9

32 7 Cable Diagrams 7. JZSP-CSI0-x-E Flying Lead - CN I/O. SERVOPACK End Connector EL (by Sumitomo 3M Ltd.) Shell 036-5A0-008 Cable (Ivory) SSRFPVV-SB AWG#8 3P UL076 VW-SC 3 Dia. Wire Markers L (6.3 Dia.) Dimensions in mm Model JZSP-CSI0--E JZSP-CSI0--E JZSP-CSI0-3-E Cable Length 000 mm 000 mm 3000 mm Pin No SERVOPACK End Wire Signal Color Color /BK+ /BK ALM+ ALM +4VIN P-OT N-OT /DEC /EXT /EXT /EXT3 /SI0 BAT + BAT SG PAO /PAO PBO /PBO PCO /PCO /SO+ /SO /SO3+ /SO3 Blue Blue Pink Pink Green Green Orange Orange Gray Gray Blue Blue Pink Pink Green Green Orange Orange Gray Gray Blue Blue Pink Pink Green Green Red Black Red Black Red Black Red Black Red Black Red Black Red Black Red Black Red Black Red Black Red Black Red Black Red Black Marking Dots Host Controller End Lead Marker Represents twisted-pair wires. 30

33 8 EMC Installation Conditions 8 EMC Installation Conditions This section gives the installation conditions that were used for EMC certification testing. The EMC installation conditions that are given here are the conditions that were used to pass testing criteria at Yaskawa. The EMC level may change under other conditions, such as the actual installation structure and wiring conditions. These Yaskawa products are designed to be built into equipment. Therefore, you must implement EMC measures and confirm compliance for the final equipment. The applicable standards are EN 550 group class A, EN , EN , and EN (category C, second environment). Three-Phase, 00 VAC Shield box Brake power supply SERVOPACK Power supply: Three-phase, 00 VAC 5 Noise filter L, L, and L3 U, V, and W 3 Brake Servomotor Surge absorber LC and LC CN 4 Encoder PE Host controller 6 CN6A and CN6B CN CN8 PE I/O controller Safety function device Symbol Cable Name Specification I/O Signal Cable Shielded cable Safety Function Device Cable Shielded cable Servomotor Main Circuit Cable Shielded cable Encoder Cable Shielded cable Main Circuit Power Cable Shielded cable EtherCAT Communications Cable Shielded cable 3

34 8 EMC Installation Conditions Single-Phase, 00 VAC Shield box Brake power supply SERVOPACK Power supply: Single-phase, 00 VAC 5 Noise filter L and L U, V, and W 3 Brake Servomotor Surge absorber LC and LC CN 4 Encoder PE Host controller 6 CN6A and CN6B CN CN8 PE I/O controller Safety function device Symbol Cable Name Specification I/O Signal Cable Shielded cable Safety Function Device Cable Shielded cable Servomotor Main Circuit Cable Shielded cable Encoder Cable Shielded cable Main Circuit Power Cable Shielded cable EtherCAT Communications Cable Shielded cable 3

35 8 EMC Installation Conditions Single-Phase, 00 VAC Shield box Brake power supply SERVOPACK Power supply: Single-phase, 00 VAC 5 Noise filter L and L U, V, and W 3 Brake Servomotor Surge absorber LC and LC CN 4 Encoder PE Host controller 6 CN6A and CN6B CN CN8 PE I/O controller Safety function device Symbol Cable Name Specification I/O Signal Cable Shielded cable Safety Function Device Cable Shielded cable Servomotor Main Circuit Cable Shielded cable Encoder Cable Shielded cable Main Circuit Power Cable Shielded cable EtherCAT Communications Cable Shielded cable 33

36 8 EMC Installation Conditions 34

37

38 IRUMA BUSINESS CENTER (SOLUTION CENTER) 480, Kamifujisawa, Iruma, Saitama, , Japan Phone: Fax: YASKAWA ELECTRIC CORPORATION New Pier Takeshiba South Tower, -6-, Kaigan, Minatoku, Tokyo, , Japan Phone: Fax: YASKAWA AMERICA, INC. Norman Drive South, Waukegan, IL 60085, U.S.A. Phone: (800) YASKAWA ( ) or Fax: YASKAWA ELÉTRICO DO BRASIL, LTDA. Avenida Piraporinha 777, Diadema, São Paulo, , Brasil Phone: Fax: YASKAWA ELECTRIC EUROPE GmbH Hauptstraβe 85, Eschborn, Germany Phone: Fax: YASKAWA ELECTRIC UK LTD. Hunt Hill Orchardton Woods, Cumbernauld, G68 9LF, United Kingdom Phone: Fax: YASKAWA ELECTRIC KOREA CORPORATION 7F, Doore Bldg. 4, Yeoido-dong, Youngdungpo-Ku, Seoul, , Korea Phone: Fax: YASKAWA ELECTRIC (SINGAPORE) PTE. LTD. 5 Lorong Chuan, #04-0, New Tech Park, 55674, Singapore Phone: Fax: YASKAWA ELECTRIC (SHANGHAI) CO., LTD. No. 8 Xizang Zhong Road, Room , Harbour Ring Plaza, Shanghai, 0000, China Phone: Fax: YASKAWA ELECTRIC (SHANGHAI) CO., LTD. BEIJING OFFICE Room 0A, Tower W3 Oriental Plaza, No. East Chang An Ave., Dong Cheng District, Beijing, 00738, China Phone: Fax: YASKAWA ELECTRIC TAIWAN CORPORATION 9F, 6, Nanking E. Rd., Sec. 3, Taipei, Taiwan Phone: Fax: MANUAL NO. IG.SL7C.0, Rev. A- Published in U.S.A June 8, 07