NJU8790. Pushbutton Interface EVR with Class D Stereo Power Amplifier NJU

Transcription

1 Pushbutton Interface EVR with Class D Stereo Power Amplifier NJU8790 GENERA DESCRIPTION The NJU8790 is a pushbutton interface electronic volume with class D stereo power amplifier. It includes input selector, electronic volume, and limiter. The NJU8790 can control the volume and the mode select without the micro-controller by the pushbutton interface. The NJU8790 is suitable for low power consumption and simple control application such as mobile audio player, active speaker and cradle speaker. PACKAGE OUTINE NJU879 FEATURES Operating Voltage operating current Output power Output filter-less Pop-noise reduction circuit Short-circuit protection circuit Supply voltage monitoring circuit 2-Input 1-Output selector Pushbutton interface EVR Active filter, limiter CMOS Technology Package Outline BOCK DIAGRAM +2.7 to +5.5V 10mA typ. (Active mode) 1µA max. (Stand-by mode) 2.7W+2.7W ( = 5V, 4ohm, BT) (Single-end / Differential) 0 to -68dB, MUTE SSOP44 (11 x 7.6 x 1.15mm, 0.5mm pitch) Mid Max Pow Power indicator Volume indicator Active filter Power Button TEST SWMODE NJU8790 PWSW SEOUT VOIN PWIND VOIND2 VOIND1 OUT EQ1 EQ2 IREF UVO VDD VREF GND VDD VDDR IN1 OUTP IN1G IN1R IN2 Input Selector Electric Volume imiter 2.7W(4ohm) 1.5W(8ohm) Stereo Class D Amp OUTN OUTRP IN2R +12dB typ. OUTRN VSS Short Protection TEST1 SESW SEOUTR VOINR VOADJ ATTADJ ATT OUTR EQ1R EQ2R INT SENSE VSS VSSR Att Active filter Up Dn Input1/Input2 Initial Vol adjuster 12, 16, 20, 24 db Att. evel adjuster 10, 15, 20, Mute NJU8790 Ver.6.1 E - 1 -

2 PIN CONFIGURATION No. Symbol Function No. Symbol Function 1 IN1 ch Input 1 23 VDD Power Supply 2 IN1G Common Input 1 24 VOIND2 Volume Indicator 2 3 IN1R Rch Input 1 25 VOIND1 Volume Indicator 1 4 IREF Reference Current 26 PWIND Power Indicator 5 SWMODE Control Mode Setting 27 TEST Test 6 ATT ATT Select Switch 28 VDD ch Output Power Supply 7 TEST1 Test 29 OUTN ch Inverted Output 8 SEOUTR Selector Output R 30 VSS ch Output GND 9 VOINR Volume Input R 31 OUTP ch Non-inverted Output 10 OUTR Volume Output Rch 32 VDD ch Output Power Supply 11 EQ1R Active Filter1 Rch 33 EQ2 Active Filter2 ch 12 EQ2R Active Filter2 Rch 34 EQ1 Active Filter1 ch 13 VDDR Rch Output Power Supply 35 OUT Volume Output 14 OUTRP Rch Non-inverted Output 36 VOIN Volume Input 15 VSSR Rch Output GND 37 SEOUT Selector Output 16 OUTRN Rch Inverted Output 38 SENSE imiter Sensitivity Setting 17 VDDR Rch Output Power Supply 39 INT Recovery Time Setting 18 SESW Input Selector 40 ATTADJ Attenuator Adjustor 19 PWSW Power ON/OFF 41 VOADJ Volume Initialization 20 Volume Up Button 42 IN2 ch Input 2 21 Volume Down Button 43 VREF Reference voltage 22 VSS GND 44 IN2R Rch Input 2 *)The relations of VSS= VSS= VSSR= and VDD= VDD=VDDR must be maintained

3 ABSOUTE MAXIMUM RATING (Ta=25 C) PARAMETER SYMBO RATING UNIT Power Supply Voltage +7 V P D mw Power Dissipation* 1) P D mw Maximum Input Voltage V IMAX 0 to * 2) V Operating Temperature Range Topr -40 to +85 C Storage Temperature Range Tstg -40 to +125 C oad Impedance R MIN >3.6 Ω * 1) Power Dissipation EIA/JEDEC STANDARD Test board (2layer or 4layer) mounting. The class-d amplifiers operate with high power efficiency and low dissipation power compared to general analog-amplifiers. In theory, the NJU8790 actualize quite high output-power such as 2.7W/channel at 5V operation into 4 ohms load, and total power is supposed to be 5.4W. For this reason, it looks as if the NJU8790 exceeds the absolute maximum rating of the power dissipation. owever, in practice, the effective output-power of usual music sound is only about 1/5 to 1/10 of its maximum output power, thus it may never exceed the absolute maximum rating. * 2) Don t apply the input voltage that exceeds supply voltage. EECTRICA RECOMMENDED OPERATING CONDITION (Ta=25 C) PARAMETER SYMBO TEST CONDITION MIN. TYP. MAX. UNIT Operating Voltage V EECTRICA CARACTERISTICS DC CARACTERISTICS1 (Ta=25 C, =5., unless otherwise specified) PARAMETER SYMBO TEST CONDITION MIN. TYP. MAX. UNIT Operating Current I DD1 No Signal, Active ma I DD2 No Signal, Standby µa Reference Voltage V REF No signal V UVO Detecting Voltage V DDDET V - 3 -

4 DC CARACTERISTICS2 (Ta=25 C, =5., unless otherwise specified) PARAMETER SYMBO TEST CONDITION MIN. TYP. MAX. UNIT Side Output Transistor Resistance Side Output Transistor Resistance R DS R DS OUTP=0.01V, OUTN=0.01V OUTRP=0.01V, OUTRN=0.01V OUTP=VDD-0.01V, OUTN=VDD-0.01V OUTRP=VDDR-0.01V, OUTRN =VDDR-0.01V Ω Ω Input Resistance R IN IN1, IN1R, IN2, IN2R kω Class-D Amplifier Switching Frequency Class-D Amplifier Turn-On Time Class-D Amplifier Turn-Off Time F OSC kz T ON PWSW :Toggle SW mode ms T OFF PWSW :Toggle SW mode ms Output Voltage V O I SOURCE =1mA (pin 23,24,25) *0.8 - V Output Voltage V O I SINK =1mA (pin 23,24,25)) 0 - *0.8 V pin 5, pin 6, pin 7, pin 18, pin 19, Input Voltage V I pin 20,pin 21, pin 27 pin 5, pin 6, pin 7, pin 18, pin 19, Input Voltage V I pin 20,pin 21, pin 27 *0.8 - V 0 - *0.2 V Pull-Down Resistance R PUDWN pin 19, pin 20,pin kω Mode Resistance range 1/4 R MODE1 pin 40, pin kω Mode Resistance range 2/4 R MODE2 pin 40, pin kω Mode Resistance range 3/4 R MODE3 pin 40, pin kω Mode Resistance range 4/4 R MODE4 pin 40, pin kω Pulse Distinction Time T JDGPS pin 19, pin 20,pin ms Auto Increment Distinction Time T JDGINC pin 19, pin 20,pin s Auto Increment cycle T AINC pin 19, pin 20,pin ms - 4 -

5 AC CARACTERISTICS1 (Ta=25 C, =5., V IN =500mVrms, f=1kz, BW=20z to 20kz, R=8Ω, VO: 0dB, unless otherwise specified) Measurement pin: OUTR(pin10), OUT(pin35) PARAMETER SYMBO TEST CONDITION MIN. TYP. MAX. UNIT Maximum Input Voltage V IM VO=-12dB TD=1% Vrms Maximum Gain G VMAX db Initial Volume 1 G VINIT1 R INIT = 0Ω db Initial Volume 2 G VINIT2 R INIT = 47kΩ db Initial Volume 3 G VINIT3 R INIT = 100kΩ db Initial Volume 4 G VINIT4 R INIT = OPEN db Maximum Attenuate level G VO-68 VO= -68dB db Mute evel Mute VO= Mute db ATT evel 1 G VATT1 R ATT =0Ω db ATT evel 2 G VATT2 R ATT =47kΩ db ATT evel 3 G VATT3 R ATT =100kΩ db ATT Mute evel G VATT4 R ATT =OPEN db Channel Balance G CB db Cross Talk CT Selected Input: No Signal, Rg=0Ω db Channel Separation CS Rg=0Ω db AC CARACTERISTICS2 (Ta=25 C, =5., V IN =500mVrms, f=1kz, BW=20z to 20kz, R=8Ω, VO: 0dB, unless otherwise specified) Measurement pin: OUTRP-OUTRN (PIN 14-PIN16), OUTP-OUTN (PIN 31-PIN29) PARAMETER SYMBO TEST CONDITION MIN. TYP. MAX. UNIT Output Power Efficiency E EFF TD=10% % TD+N TD+N P O =1W % Output Power1 Po TD+N=10%, R =8Ω W/ch Output Power2 Po TD+N=10%, R =4Ω W/ch imit evel V IM V IN =0.7Vrms,R SENSE =56kΩ No-load Vrms Power Amplifier Gain Av No-load db Output Noise Voltage 1 V NO1 Rg=0Ω, A-weighted - Output Noise Voltage 2 TD+N Measurement Circuit V NO2 Rg=0Ω, A-weighted VO=-68dB (100) -80 (100) - - dbv (µvrms) dbv (µvrms) NJU8790 AUX 0025 Filters 20kz(AES17) TD METER Evaluation Board PF Audio Analyzer - 5 -

6 PIN DESCRIPTION SWMODE (pin 5) and PWSW (pin 19) SWMODE (pin 5) PWSW(pin 19) Momentary SW mode setting Toggle SW mode setting Momentary SW mode data format System status is changed to active mode and standby mode alternately. No change. Active mode Standby Mode. Mode Change [Active] Mode Change [Standby] Mode Change [Active] Toggle SW mode data format Mode Change [Active] Mode Change [Standby] Mode Change [Active] ATT (pin 6) Toggle SW Mode PIN CONDITION Attenuator: OFF Attenuator: ON. SESW (pin 18) Toggle SW Mode PIN CONDITION IN1R, IN1 signals are selected. IN2R, IN2 signals are selected

7 (pin 20) PIN CONDITION OPEN() OPEN() Volume setting is increased 1 step. In the cace that signal inputs more than Auto Increment Distinction Time, volume setting is increased continuously. No change. * The Toggle SW mode does not support. (pin 21) PIN CONDITION OPEN() OPEN() Volume setting is decreased 1 step. In the cace that signal inputs more than Auto Increment Distinction Time, volume setting is decreased continuously. No change. * The Toggle SW mode does not support. TEST (pin 27) PIN CONDITION Normal operation mode Test mode. Do not use for normal operation. TEST1 (pin 7) PIN CONDITION Normal operation mode Test mode. Do not use for normal operation. VOADJ (pin 41) CONNECTED RESISTANCE 0Ω to 20kΩ 40Ω to 60kΩ 90kΩ to 110kΩ 150kΩ to OPEN Volume initial value: -12dB Volume initial value: -16dB Volume initial value: -20dB Volume initial value: -24dB ATTADJ (pin 40) CONNECTED RESISTANCE 0Ω to 20kΩ 40Ω to 60kΩ 90kΩ to 110kΩ 150kΩ to OPEN Attenuator initial value: -10dB Attenuator initial value: -15dB Attenuator initial value: -20dB Mute - 7 -

8 CONTRO DATA INITIA CONDITION (POWER ON) TERMINA CONDITION Power Pin 19 Standby Volume Pin 20, Pin 21-12dB, -16dB, -20dB, -24dB Volume gain step setting Step No. Volume [db] 0 MUTE (*) (*) (*) (*) (*) Initial Setting - 8 -

9 INDICATOR PWIND (pin 26) CONDITION Class-D Amplifier Standby Class-D Amplifier Active PIN VOTAGE VOIND1 (pin 25) CONDITION Volume setting is not 0dB Volume setting is 0dB (Max.) PIN VOTAGE VOIND2 (pin 24) CONDITION Volume setting is 26dB or lower Volume setting is 24dB or higher PIN VOTAGE - 9 -

10 TIMING CART PWSW Momentary SW mode Standby release (Standby mode Active mode) PWSW (pin19) 20ms (Pulse Distinction Time) PWIND (pin26) 244ms OUTR, OUT (pin10, 35) /2 OUTRP OUTRN (pin14, 16) OUTN, OUTP (pin29, 31) Standby (Active mode Standby mode) PWSW (pin19) 20ms (Pulse Distinction Time) PWIND (pin26) 244ms OUTR, OUT (pin10, 35) /2 OUTRP OUTRN (pin14, 16) OUTN, OUTP (pin29, 31)

11 PWSW Toggle SW mode Standby release (Standby mode Active mode) PWSW (pin19) 20ms (Pulse Distinction Time) PWIND (pin26) OUTR, OUT (pin10, 35) /2 OUTRP OUTRN (pin14, 16) OUTN, OUTP (pin29, 31) 244ms (Class-D Amplifier Turn-On Time) Standby (Active mode Standby mode) PWSW (pin19) 20ms (Pulse Distinction Time) PWIND (pin26) OUTR, OUT (pin10, 35) /2 OUTRP OUTRN (pin14, 16) OUTN, OUTP (pin29, 31) 244ms (Class-D Amplifier Turn-Off Time)

12 Input Selector SESW (pin18) Input 1 Input 2 20ms 64ms OUTR(pin10) OUT(pin35) /2-12 -

13 Volume / control 1. Recognition condition of Volume / push button I/F 1-a.) The Volume /() recognizes the data-command to the case that the () button has not been pushed, besides that the () button is pushed for the longer time than the Pulse Distinction Time: 20ms". 1-b.) The Volume /() recognizes the data-command to the case that the () button has pushed earlier than the () button, besides the () button is pushed for the longer time than the Pulse Distinction Time: 20ms". > Pulse Distinction Time (20ms typ.) Recognition > Pulse Distinction Time (20ms typ.) Recognition 1-a 1-b 2. Invalidity condition of Volume / push button I/F 2-a.) The Volume /() does NOT recognize the data-command to the case that the () button has pushed for the shorter time than the Pulse Distinction Time: 20ms". (The Chattering prevention function operates.) 2-b.) The Volume /() does NOT recognize the data-command to the case that the () button has pushed for the shorter time than the Pulse Distinction Time: 20ms" after released button. (The Chattering prevention function operates.) 2-c.) The Volume /() does NOT recognize the data-command to the case that the () button has pushed before releasing () button. < Pulse Distinction Time (20ms typ.) < Pulse Distinction Time (20ms typ.) 2-a 2-b 2-c

14 3. Start condition of Volume / Auto increment function 3-a.) The Auto increment of volume () is started to the case that the () button has not been pushed, besides that the () button is pushed for the longer time than the Auto increment Distinction Time: 1s". > Auto increment Distinction Time (1s typ.) Auto increment starts OUTR(pin10) OUT(pin35) Auto Increment cycle 3 a 4. Stop condition of Volume / Auto increment function 4-a.) The Auto increment of volume () is stopped to the case that the () button has released for the longer time than the Pulse Distinction Time: 20ms" for the Auto increment period. 4-b.) The Auto increment of volume () is stopped to the case that the () button has pushed for the Auto increment period. Auto increment Distinction Time (1s typ.) Increment start Pulse Distinction Time (20ms typ.) Auto increment Distinction Time (1s typ.) Increment start Increment stop Increment stop 4-a 4-b

15 APPICATION CIRCUIT Mid Max Pow Power Button R4=10kΩ R3=9.1kΩ Power indicator R11 R10 Q1 R14 R15 Q3 Volume indicator R13 Q2 R12 R2=100kΩ C6=100pF C18=0.1μF C10=1μF C7=0.1μF C8=4.7μF C17=4.7μF C4=4.7μF C5=0.47μF C16=0.1μF TEST SWMODE NJU8790 PWSW SEOUT VOIN PWIND VOIND2 VOIND1 OUT EQ1 EQ2 IREF VDD UVO VREF GND VDD VDDR C1=0.47μF IN1 OUTP SOUND IC C2=1μF C3=0.47μF C11=0.47μF IN1G IN1R IN2 Input Selector Electric Volume imiter 2.7W(4ohm) 1.5W(8ohm) Stereo Class D Amp OUTN OUTRP C9=0.47μF IN2R +12dB typ. OUTRN VSS Short Protection TEST1 SESW SEOUTR VOINR VOADJ ATTADJ ATT OUTR EQ1R EQ2R INT SENSE VSS VSSR C13=4.7μF C14 =0.47μF R8=9.1kΩ R6=0Ω to OPEN Att R9=10kΩ R5=0Ω to OPEN Up Dn C15=100pF C12=1μF R7=56kΩ Input1/Input2 [CAUTION] The specifications on this databook are only given for information, without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights