Electronic Preset Delivery System. AccuLoad II TM. Installation. The Most Trusted Name In Measurement

Transcription

1 Electronic Preset Delivery System AccuLoad II TM Issue/Rev. 0.8 (8/95) Installation Bulletin MN06037 The Most Trusted Name In Measurement

2

3

4

5

6

7

8

9

10

11

12

13 Section 1 - General J4 J5 J3, J6, J7 and J8 J1 J2 Figure 2 InterFace Board MN06037 Issue/Rev. 0.8 (8/95) 7

14

15 Section 1 - General Note: Dimensions - Inches to the nearest tenth (millimeteres to the nearest whole mm), each independently dimensioned from respective engineering drawings. Figure 4 AccuLoad II NEMA IV Dimensions MN06037 Issue/Rev. 0.8 (8/95) 9

16

17 Section I - General Notes: 1. If security switches are not used, these terminals should be tied to the incoming power line. 2. Jumper Positions shown for 120 or 240 operation. 3. Preset Position #1 - Red - DC connections 1 through 24, 43, and 44 - AC connections 73 and 74, 80 through Preset Position #2 - Yellow - DC connections 45 and 46, 49 through 72 - AC connections 75 and 76, 106 through Common to both Preset Positions - White - DC connections 25 through 42 - AC connections 77 through 79, 132 through 134 Figure 6 Terminal Block Layout - Graphics Panel MN06037 Issue/Rev. 0.8 (8/95) 11

18

19

20

21

22

23

24

25

26

27 Section 1 - General Printer Output Jumpers 1. After assembling QOPV kit to AccuLoad II, connect numbered wires from header (part of QOPV Board) to corresponding terminal points on AccuLoad II I/O Board. Figure 16 Quad OPV MN06037 Issue/Rev. 0.8 (8/95) 21

28 Section 1 - General for Remote Start on Position #2 for Remote Start on Position #1 1. Locate jumper locations J1 and J2 on the keypad board. 2. Mount shunt plugs as indicated above for both J1 and J2. (J1 - Preset Position #1 and J2 - Preset Position #2). 3. Wire remote start input to ac terminal 103 (Preset Position #1) and ac terminal 110 (Preset Position #2). 4. Program both Preset Positions for Remote Stop under Permissive Sense #1 in the 800 directory of the program. Figure 17 Remote Start 22 MN06037 Issue/Rev. 0.8 (8/95)

29 Section 1 - General 1. Locate jumper locations J8 and J9 on the computer board. 2. Mount shunt plugs as indicated above in lower two positions of both J8 and J9. (J8 - Preset Position #2 and J9 - Preset Position #1) 3. Wire remote stop input to ac terminal 104 ( Preset Position #1) and ac terminal 111 (Preset Position #2). 4. Program both Preset Positions for Remote Stop under Permissive Sense #2 in the 800 directory of the program. Figure 18 Remote Stop MN06037 Issue/Rev. 0.8 (8/95) 23

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59 Section 4 - AccuLoad II-SEQ A D C B External Permissives Input #6 Input #4 Input #5 AccuLoad II Preset Position # Voltage Sense Voltage Sense Voltage Sense Stop Relay Relay #1 Relay #2 Relay #3 Relay #4 Pump Relay #5 Upstream Downstream N.C. N.O. N.C. 210 Valve Upstream Sol. Downstream Sol. R1 R2 AIJ-1 Sol. AIJ-2 Sol. AIJ-3 Sol. AIJ-4 Sol. Input #3 Input #1 Input # Voltage Sense Voltage Sense Voltage Sense N.C. 113 N.C. A Temperature Probe (100 Ω) Red Red Black Black PPS Transmitter N.C. N.C Shield -12V Meter Power Common Channel A Channel B N.C. Load Printer N.C. N.C. +4 to ma -4 to 20 Input 2 70 Densitometer +4 to ma -4 to 20 Input Vdc 24V Return 1 Pressure Xducer Transducer Power B Note: 1. If external relay permissives are used in series with AccuLoad II relays, an RC network must be placed in parallel with the permissive to prevent a false turn on of the AccuLoad II relays. Recommended RC network = 0.1 uf capacitor and a 680 ohm resistor (Electrocube part number RG ). 2. Any device shown outside of the AccuLoad II housing is to be supplied by the customer. 3. Dotted connection lines indicate options. 4. For other meter transmitter connections, see Figure 33 for specific connections. Figure 38 AccuLoad II Wiring Schematic (Preset Position 2) MN06037 Issue/Rev. 0.8 (8/95) 53

60

61

62

63

64

65

66

67

68

69 Section 5 - Related Publications The following literature can be obtained from FMC Technologies Measurements Solutions, Inc. Literature Fulfillment at johno@gohrs.com or online at When requesting literature from Literature Fulfillment, please reference the appropriate brochure number and title. Valves Model Specifications... Bulletin SS03009 Model Installation/Operation...Bulletin MN03010 Model Specifications... Bulletin SS03010 Model Installation/Operation...Bulletin MN03006 Model Service...Bulletin MN03007 Parts List... Consult Parts Operation The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the specifications are currently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications which may have been changed and are no longer in effect. Headquarters: 1803 Gears Road, Houston, TX USA, Phone: 281/ , Fax: 281/ Gas Measurement Products: Erie, PA USA Phone 814/ Thetford, England Phone (44) Kongsberg, Norway Phone (47) 32/ Buenos Aires, Argentina Phone 54 (11) Integrated Measurement Systems: Corpus Christi, TX USA Phone 361/ Kongsberg, Norway Phone (47) 32/ San Juan, Puerto Rico Phone 787/ United Arab Emirates, Dubai Phone / Visit our website at Liquid Measurement Products: Erie, PA USA Phone 814/ Los Angeles, CA USA Phone 661/ Slough, England Phone (44) Ellerbek, Germany Phone (49) Barcelona, Spain Phone (34) 93/ Moscow, Russia Phone (7) 495/ Melbourne, Australia Phone (61) 3/ Printed in U.S.A. 8/95 FMC Technologies Measurement Solutions, Inc. All rights reserved. MN06037 Issue/Rev. 0.8 (8/95) Beijing, China Phone (86) 10/ Singapore Phone (65) Chennai, India Phone (91) 44/