S0 pulse counter. with S-Bus interface. Main features: Order number. Technical Data. Mounting
|
|
- Pauline Alannah Mitchell
- 6 years ago
- Views:
Transcription
1 Data sheet S pulse counter with S-Bus interface The S-S-Bus coupler module is a device for the collection of S pulses. With this module the consumption data of any measurement device with a S output becomes bus capable and can be accessed by every Saia PCD or Energy Manager through the S-Bus. Main features: Up to S-S-Bus Modules on the same bus 4 S pulse inputs (S+... S4+) per S-S-Bus Module Up to 4 S devices on the same S-Bus The inputs comply with the S standard Integrated RS-485 termination resistor LED for bus activity indication Order number PCD7.H4SE Technical Data Protection type as DIN45 Operating voltage Un Current draw Power draw IP 4 connections IP 2 23 VAC (-2/+5%) < 2 ma < 3 W Temperature - Operation -25 C +55 C - Storage -25 C +7 C EMC / noise immunity Insulation characteristics LEDs - Surge voltage according to IEC6-4-5 on main electric circuit, 4 kv.2 / 5 μs - Surge voltage according to IEC6-4-5 at S inputs, kv.2/5 μs - Burst voltage according to IEC Main electric circuit 4 kv direct - S inputs 2 kv capacitive - S-Bus connections kv capacitive - ESD according to IEC6-4-2, - Contact 8 kv, air 8 kv - 4 kv / 5 Hz test according to VDE435-6 kv.2 / 5 μs surge voltage according to IEC Device protection class II - Run indication by green LED (On) - Function indication by red LED when bus active Mounting Mounting Connections On 35 mm DIN top-hat rail (EN522) any mounting position - For Pozidrive, Philips or slot-head screwdriver N - Sx, S-Bus, 23 VAC mm 2
2 Dimensioned drawings Display elements / settings Switch for RS-485 bus termination resistor Rotary switches for S-Bus address selection Comm LED: indicates bus activity On LED: power indicator S inputs Comply with S standard EN Counts pulses as when R < 8 Ω Counts pulses as when R > MΩ Voltage max. (GND-S) 3 VDC Current max. ( with Ω) 6 ma Pulses low min. 3 ms Pulses high min. 3 ms Frequency max. 7 Hz Changing the S-Bus-Address Switch o 23 VAC Set new address Switch on 23 VAC Note: The address setting will only be read when the module supply (23 VAC) is switched on. 2 PCD7.H4SE S pulse counter with S-Bus interface Datasheet
3 F 5 E E E Wirings Diagram D /D S-Bus, pair of wires, twisted 554 Example Addressing Address high VAC max. 2 m S- GND (common) 9 Address low Address low R R R R Address 5 Ω < R < 8 Ω S+ S+ S2+ S3+ S4+ GND Note: If the S-S-Bus module is used in the S-Bus as last device, then the sliding switch «RS-485 Terminate» need to be in the position «On». Technical data S-Bus Bus system S-Bus Transmission rate The transmission Baud rate is automatically detected Transmission mode Data Bus length (max.) 2 m (without repeater) Response time: Write: 3 ms Read: 2 ms The communication is ready 3 s after the Power On For a description of the used Registers please look at the Register Page Data transmission Only «read/write» register instructions are recognized. Only one register can be written at a time. The device will respond «NAK» if more than register is written. Up to 2 Registers could be read at a time. The device will respond «NAK» if more than 2 registers are read. The device will not respond to any unknown query. The device has a voltage monitoring system. In case of voltage loss, registers are stored in EEPROM (transmission rate» etc.) Datasheet PCD7.H4SE S pulse counter with S-Bus interface 3
4 Register R Read Write Description Unit or Value X Firmware-Version Ex: = FW. X S-Bus com. number of supported registers will give «38» 2 X S-Bus com. number of supported flags will give 3 X Baudrate BPS 4 Not used will give a 5 X Type/ASN Function will give «PCD7» 6 X Type/ASN Function will give «H4» 7 X Type/ASN Function will give «SE» 8 X Type/ASN Function will give 9 X HW Vers. Modif Ex: = HW. Not used will give a Not used will give a 2 X serial number will give the serial number 3 Not used will give a 4 X Status/Protect = no Problem = Problem with last communication request 5 X S-Bus Timeout ms 6 X S-Bus Address Not used will give a 8 Not used will give a 9 Not used will give a 2 X X Counter S Ex: 9235= 9235/2 = kwh 2 X X Counter S2 Ex: 9235= 9235/2 = kwh 22 X X Counter S3 Ex: 9235= 9235/2 = kwh 23 X X Counter S4 Ex: 9235= 9235/2 = kwh 24 X X Impulses per unit for S Ex: 2 = 2 Imp/kWh 25 X X Impulses per unit for S2 Ex: 2 = 2 Imp/kWh 26 X X Impulses per unit for S3 Ex: 2 = 2 Imp/kWh 27 X X Impulses per unit for S4 Ex: 2 = 2 Imp/kWh 28 X X ID for S User defined identification number 29 X X ID for S2 User defined identification number 3 X X ID for S3 User defined identification number 3 X X ID for S4 User defined identification number 32 Not used will give a 33 Not used will give a 34 Not used will give a 35 Not used will give a 36 X X Transmission speed : 5 2 2: : : 9 2 5: 96 6: 48 7: X X Auto-Baud ON : Auto-Baud detect OFF : Auto-Baud detect ON 4 PCD7.H4SE S pulse counter with S-Bus interface Datasheet
5 Datasheet PCD7.H4SE S pulse counter with S-Bus interface 5
6 Saia-Burgess Controls AG Bahnhofstrasse Murten, Switzerland T F support@saia-pcd.com PP ENG Subject to change without notice
3-Phase Energy meter for high current measurement converter with Serial S-Bus interface
Data sheet www.sbc-support.com 3-Phase Energy meter for high current measurement converter with Serial S-Bus interface Energy meters with an integrated S-Bus interface allow direct reading of all relevant
More information3-Phase Energy meter with Serial S-Bus interface
Data sheet www.sbc-support.com 3-Phase Energy meter with Serial S-Bus interface Energy meters with an integrated Serial S-Bus interface allow direct reading of all relevant data, such as energy (Total
More information3-Phase Energy meter with serial S-Bus interface
Data sheet www.sbc-support.com 3-Phase Energy meter with serial S-Bus interface Energy meters with an integrated S-Bus interface allow direct reading of all relevant data, such as energy (Total and partial),
More informationData sheet Energy meter with integrated S-Bus interface
Data sheet Energy meter with integrated S-Bus interface Controls Division Bus AWD3 Energy meters with an integrated S-Bus interface allow direct reading of all relevant data, such as energy (Total and
More information3 phase energy meters with integrated Serial Modbus interface
Data sheet www.sbc-support.com 3 phase energy meters with integrated Serial Modbus interface Energy meters with an integrated Serial RS-485 Modbus interface allow direct reading of all relevant data, such
More informationThree-phase energy meter for transformer connection with S0 pulse output
Data sheet www.sbc-support.com Three-phase energy meter for transformer connection with S0 pulse output The S0 interface is a hardware interface for the transmission of measured values via pulses. Main
More informationSingle phase energy meter with Serial Modbus interface
Data sheet www.sbc-support.com Single phase energy meter with Serial Modbus interface Energy meters with a Serial RS-485 Modbus interface allow direct reading of all relevant data, such as energy (total
More information3-phase energy meters with S0 pulse output
Data sheet www.sbc-support.com 3-phase energy meters with S0 pulse output The S0 interface is a hardware interface for the transmission of measured values via pulses. Main features ff 3-phase energy meter,
More informationData sheet AWD3 3-phase, bidirectional energy meter for current converter metering with integrated S0-output Controls Division
Data sheet AWD3 3-phase, bidirectional energy meter for current converter metering with integrated S0-output Controls Division Bidirectional energy meter with LC display and integrated S0-interface. The
More informationHardware Manual. PCD3.F240/PCD2.F2400 LON interface module for TP/FT-10 channel. Hardware Manual PCD3.F240/PCD2.F2400, LON interface module
Hardware Manual PCD3.F240 PCD2.F2400 PCD3.F240/PCD2.F2400 for TP/FT-10 channel Saia-Burgess Controls AG, 3280 Murten Page 1/12 0.1 Document history... 3 0.2 Trademarks... 3 1 F240/F2400... 4 1.1 Module
More informationEMU Electronic AG. Jöchlerweg 4 CH-6340 Baar Switzerland Telefon +41 (0) Fax +41 (0)
EMU Electronic AG 3-phase Energy Meter with MID B and D EMU Elektronik AG Jöchlerweg 4, 6340 Baar Switzerland Tel. +41 (0)41 811 02 20 Fax +41 (0)41 811 02 21 Info@emuag.ch / www.emuag.ch Jöchlerweg 4
More informationINTELLIGENT DIGITAL MULTI POWER METER [DIC-MPM]
Feature Suit for LV/ HV voltage system Compact design with all real-time measurement Consist of basic unit and optional modules 10 years back-up of integrated energy data Large LCD, high brightness High
More informationEnergy Management Energy Meter with plug-in Output Modules Type EM4-DIN
Energy Management Energy Meter with plug-in Output Modules Type EM4-DIN Degree of protection (front): IP 40 Front dimensions: 9 DIN modules RS 422/485 Serial port by means of optional module Dual pulse
More informationNEW Series STH Output to 75A, 600 Vac High Industrial Performance (HIPpak) Solid-State Relays
FEATURES/BENEFITS Zero-cross models for resistive loads Low zero-cross turn-on voltage Input protection and control LED standard IP20 touch-proof flaps optional Connectors for power wiring and heat sinks
More information12/2 Product overview. 12/3 7KT1 14, 7KT1 53 E-counters. 12/9 7KT1 11, 7KT1 12 digital measuring devices. 12/11 7KT1 0 analog measuring devices
BETA Measuring /2 Product overview /3 7KT1 14, 7KT1 53 E-counters /9 7KT1 11, 7KT1 digital measuring devices /11 7KT1 0 analog measuring devices / 7KT5 8 time and pulse counters /14 7KT5 5, 7KT5 6 time
More informationEnergy Management Energy Meter Type EM110
Energy Management Energy Meter Type EM110 Single phase energy meter Class 1 (kwh according to EN62053-21 Class B (kwh according to EN50470-3 Electro-mechanical display Energy readout on display: 6+1 digit
More informationEnergy Management Energy Meter Type EM111
Energy Management Energy Meter Type EM111 Easy connection or wrong current direction detection Other versions available (not certified, option X: see how to order on the next page Single phase energy meter
More informationEnergy Meters for DIN Rail Mounting Electric energy meter WS0101, WS0102,WS1102 WS0301, WS0302,WS1302
Energy Meters for DIN Rail Mounting Electric energy meter WS0101, WS0102,WS1102 WS0301, WS0302,WS1302 Direct connection up to 65 A (WSx10x) Connection with current transformer (WSx30x) Industrial or meters
More informationEnergy Management Energy Meter Type EM112
Energy Management Energy Meter Type EM112 Easy connection or wrong current direction detection Other versions available (not certified, option X: see how to order on the next page Single phase energy meter
More informationMID. Energy Management Energy Meter Type EM23 DIN. Product Description. Type Selection. How to order EM23 DIN AV9 3 X O1 PF A EM23 DIN
Energy Management Energy Meter Type EM23 DIN Certified according to MID Directive (option PF only): see how to order below Other version available (not certified, option X): see how to order on the next
More informationC series Product brief
Product brief Key applications Landlord sub-metering Object metering Meter performance Direct connected up to 0 ctive energy Low power consumption larm function Pulse output Installation Small size - 1
More informationEnergy Management Energy Meter Type EM340
Energy Management Energy Meter Type EM340 Digital input (for tariff management Easy connection or wrong current direction detection Certified according to MID Directive (option PF only: see how to order
More informationEnergy Management Energy Meter Type EM110
Energy Management Energy Meter Type EM110 Single phase energy meter Class 1 (kwh according to EN62053-21 Class B (kwh according to EN50470-3 Electro-mechanical display Energy readout on display: 6+1 digit
More informationEnergy Management Three-phase energy meter with output modules Type EM4-DIN
Energy Management Three-phase energy meter with output modules Type EM4-DIN Class 1 (active energy) Class 2 (reactive energy) Three-phase multi-function energy meter Back-lighted LCD display 3 1 / 2 DGT
More informationISOMETER IRDH575. Approvals
Insulation monitoring device for unearthed AC, DC and AC/DC systems (IT systems) with control and display function for EDS insulation fault location systems IRDH575_D00089_02_D_XXEN/09.2018 Insulation
More informationMCR-VAC-UI-0-DC. Voltage transducer for AC voltages. INTERFACE Data sheet _en_02. 1 Description
Voltage transducer for AC voltages TERFACE Data sheet 006_en_0 PHOENIX CONTACT 00-0- Description The MCR voltage transducer measures AC voltages in several signal ranges from 0... ±4 V AC to 0... ±30 V
More information08/07/2015
17.5 mm - 1 Relay 8A MUR1 Part number 88827105 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external load connection
More informationRI-D440. Three Phase easywire Multifunction DIN Rail Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-D440 Three Phase easywire Multifunction DIN Rail Energy Meter Four module DIN rail mounted Energy pulse LED 330mV Input from easywire CTs (or -/1A and -/5A current transformer input with TAS-SCTEWA
More informationSolid-state Timer H3DS
Solid-state Timer H3DS DIN Track Mounted, Standard 17.5-mm Width Timer Range A wide AC/DC power supply range (24 to 230 VAC/ 24 to 48 VDC) reduces the number of timer models kept in stock. (24 to 230 VAC/VDC
More informationMID. Energy Management Energy Meter Type EM33 DIN. Product Description. How to order EM33 DIN AV3 3 X XS PF. Type Selection EM33 DIN
Energy Management Energy Meter Type EM33 DIN Easy connections management Certified according to MID Directive (option PF only): see how to order below Other version available (not certified, option X):
More information400,440Vac Vdc V, A, W, VA, var, Hz, V, Avg. A cos phi, sin phi and phi measurement kwh, kvarh (via Pulse Output)
MODEL EM4000ACF Multifunction Transducer for alternating voltage and current Power supply voltages: Suitable for DIN-rail mounting 85 240Vac 400,440Vac 24 65Vdc 100..330Vdc V, A, W, VA, var, Hz, V, Avg.
More informationSingle phase meter with direct connection and pulse or Modbus RS485 output
87045 LIMOGES Cedex Telephone: +33(0)5 55 06 87 87 Fax: +33(0)5 55 06 88 88 Single phase meter with direct connection CONTENTS PAGES 1. Description, usage... 1 2. Range... 1 3. Dimensions... 1 4. Positioning...
More informationMETERSUK. SmartLink D Y N A M i T E. EM415 MOD Series. User Manual KEY FEATURES INDEX 3. TECHNICAL DESCRIPTION. Single Phase Metering
METERSUK LTD s a l e s @ m e t e r s. c o. u k 0 1 5 2 4 5 5 5 9 2 9 Series Smart Energy Meter KEY FEATURES Single Phase Metering Single phase metering 4 din modules, Standard DIN rail Format (DIN43880)
More informationEnergy Management Energy Analyzer Type EM111
Energy Management Energy Analyzer Type EM111 Single phase energy analyzer Class 1 (kwh according to EN62053-21 Class B (kwh according to EN50470-3 Accuracy ±0.5% RDG (current/voltage Direct current measurement
More informationVFSC9 ELECTRONIC SPEED CONTROLLER. Mounting and operating instructions
ELECTRONIC SPEED CONTROLLER Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 5 WIRING
More informationMID. Energy Management Energy Analyzer Type EM11 DIN. Product Description. How to order EM11 DIN AV8 1 X O1 PF. Type Selection EM11 DIN
Energy Management Energy Analyzer Type EM11 DIN Other versions available (not certified, option X): see how to order on the next page Product Description Class 1 (kwh) according to EN62053-21 Class B (kwh)
More information08/07/2015
17.5 mm - 1 Solid State Relay 0.7A MUS2 Part number 88827004 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external
More informationMulti-channel DC power digital isolation transducer manual CE-AD81-34MN3-0.5
Multi-channel DC power digital isolation transducer manual CE-AD81-34MN3-0.5 1 Overview The main function of this product is to centralized measurement convert multi-channel standard DC transmission signal
More informationAIO and DIO PFXLM4B01DAK:Sink Output Type PFXLM401DAC:Source Output Type Virtual Resolution (pixels)
Model:PFXLM4B01DDK PFXLM4B01DDC PFXLM4B01DAK PFXLM4B01DAC LT4000M Rear module Model Name Indication PFXLM4B01 D * * (1) (2) (3) (4) Notice to our valued customers who use LT4000M series (analog model)
More informationPower analyzers and Energy Meters Power Analyzer Type WM14-DIN
Power analyzers and Energy Meters Power Analyzer Type WM14-DIN Optional RS422/485 serial port Alarms (visual only) V LN, An Class 2 (active energy) Class 3 (reactive energy) Accuracy ±0.5 F.S. (current/voltage)
More informationRI-F200 Series. Single and Three Phase Multifunction Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-F200 Series Single and Three Phase Multifunction Energy Meter DIN 96 panel mounted -/1A or -/5A current transformer input Single phase or three phase network compatible Programmable voltage and current
More informationModel Number Structure. Ordering Information. Solid-state Power OFF-delay Timer H3DE-H. Model Number Legend. List of Models
Solid-state Power OFF-delay Timer H3DE-H Timers Two delay-time models available. 0.1 to 12 seconds (S Series) 1 to 120 seconds (L Series) Covers wide range of supply voltage. Model Number Structure Model
More informationEnergy Management Power Analyzer with plug-in Output Modules Type W M22-DIN
Energy Management Power Analyzer with plug-in Output Modules Type W M22-DIN Front dimensions: 9 DIN modules Analogue output by means of optional module (20mA or 10VDC) RS 422/485 Serial port by means of
More informationEnergy Management Energy Meter GM3D
Energy Management Energy Meter Class 1 (kwh) according to EN62053-21 Class B (kwh) according to EN50470-3 Accuracy ±0.5 RDG (current/voltage) Energy meter Instantaneous variables readout: 3 DGT Energies
More informationMT372 Three-phase electronic meter with built-in modem or RS485 communication interface
Energy Measurement and Management MT372 Three-phase electronic meter with built-in modem or RS485 communication interface Technical Description Version 1, 09.06. 2005 Content: MT372 Three-phase electronic
More informationEnergy Management Energy Meter GM3T E GM3T-RS485 E
Energy Management Energy Meter GM3T E09 814 96 GM3T-RS485 E09 816 65 Certified according to MID Directive Product Description Three-phase energy meter with removable front LCD display unit. The same unit
More informationVert-X 22E - 24V / 4-20mA. Applications Wind vanes Valve control Level sensor Special purpose vehicles
Sensor principle MH-C MH-C2 Electrical data Measuring range 0... 360 0... 360 Indep. linearitiy (without misalignment) % of meas. range ±0.3 ±0.3 Indep. linearitiy (with allowed misalignment @ 360 ) %
More information05/09/2012
17.5 mm EMER8 Part number 88829198 Multifunction or mono-function Multi-range (7 ranges) Multi-voltage or single voltage Screw terminals LED status indicator (1 voltage present LED, 1 timer ON LED) Option
More informationEnergy Management Energy Meter Type EM21 72R Retro-Fit
Energy Management Energy Meter Type EM21 72R Retro-Fit Including 3 miniature split-core current sensors 10mm (90A), 16mm (150A) and 24mm (250A) diameter holes Class A (kwh) according to EN50470-3 Class
More informationNOVOHALL Rotary Sensor non-contacting. Series RSC2800 digital SSI, SPI, Incremental
NOVOHALL Rotary Sensor non-contacting Series RSC2800 digital SSI, SPI, Incremental The RSC 2800 sensor utilizes a contactless magnetic measurement technology to determine the measured angle. Unlike conventional
More informationVert-X 22E - 5V / % Ub. Applications Wind vanes Valve control Level sensor Special purpose vehicles
Sensor principle MH-C MH-C2 Electrical data Measuring range 0... 360 0... 360 Indep. linearitiy (without misalignment) % of meas. range ±0.3 ±0.3 Indep. linearitiy (with allowed misalignment @ 360 ) %
More informationMID energy meter B21 Single-phase energy meter, 65 A
MID energy meter B2 Single-phase energy meter, 5 Single-phase energy meter ( + ) Direct connection up to 5 Width, 2 DI modules Tested and approved per MID * and IEC * Regional different requirements apply
More informationFault indicator. Application. SPEF 3A2 C 1MRS MBG Issued: April 1999 Status: Updated Version: B/ Data subject to change without notice
Issued: April 1999 Status: Updated Version: B/08.11.200 Data subject to change without notice Features Versatile, multifunction line fault indicator for distribution networks Overcurrent, earth-fault and
More informationIntroduction DIN rail mounted electricity meters
Introduction DIN rail mounted electricity meters Modular DIN Rail Products offer a wide range of functions to be integrated in electrical installations with significant benefits for the user. DIN rail
More informationSolid-state Twin Timer
Solid-state Twin Timer -F Operates in flicker- or flicker- start mode with one Unit. Independent - and -time settings. Combinations of long - or -time and short - or -time setting are possible. Long time
More informationElectronic timer CT-ERS ON-delayed with 2 c/o contacts Data sheet
1SVR 430 103 F0200 CT-ERS 1 7 2 6 5 4 8 3 1 10 selectable time ranges, from 0.05 s to 300 h 2 Potentiometer with direct reading scale for the fine adjustment of the time delay 3 Sliding switch to set the
More informationCXE880 FIBRE OPTIC NODE
Kari Mäki 4.3.2008 1(6) CXE880 FIBRE OPTIC NODE The CXE880 is a fibre deep optical node. It is designed for cases where high performance and cost effectiveness are a demand. Requirements of future networks,
More information1 2 3 GridVis Pulse output 2 tariffs Modbus MID M-Bus
speicher MID energy meter ECSEM series Emax 2 Tariffs GridVis 7 Tariffs 8 Tariffs 14 Tariffs 0,2 kwh Class 0,5 kwh Class 1,0 kwh Class Pulse output Tarife 2 tariffs Messgenauigkeit Modbus MID M-Bus eratureingang
More information3-phase meter with direct connection and pulse or Modbus RS485 output
87045 LIMOGES Cedex Telephone: +33 (0)5 55 06 87 87 Fax: +33 (0)5 55 06 88 88 3-phase meter with direct connection and CONTENTS PAGES 1. Description, usage... 1 2. Range... 1 3. Dimensions... 1 4. Positioning...
More informationPosition Indicator with/without Limit Values
.1 Position Indicator with/without Limit Values Large, 6-digit, 14 mm high LED display Prescaler 2 variable limit values Eeasy direct selection by 2 function keys Rrelay output with two change-over contacts
More informationDigital Panel Meter K3TE. Model Number Structure. Model Number Legend. Easy-to-use, Low-cost Digital Panel Meter that Accepts DC Input K3TE
Digital Panel Meter K3TE Easy-to-use, Low-cost Digital Panel Meter that Accepts DC Input Compact DIN-size (96 x 48 (W x H)) body. Mounting thickness of only 3.5 mm required. Highly visible display with
More informationUniversal measuring transducer
Universal measuring transducer EM4000 Compact housing High accuracy Full galvanic separation MODbus (RS232/RS485) 3 Analogue + 1 Pulse output Direct voltagemeasurement up to 690V 48 hour service EXW ELEQ
More informationVert-X 27E - 24V / 4-20mA. Applications Harvesting machine Fork lift Hydraulic pump
Sensor principle MH-C MH-C2 Electrical data Measuring range 0... 360 0... 360 Indep. linearitiy (without misalignment) % of meas. range ±0.3 ±0.3 Indep. linearitiy (with allowed misalignment @ 360 ) %
More informationEnvironmental Influences. Display. Inputs and Outputs. Electromagnetic Compatibility. Communication Interfaces. Insulation Strenght.
Electricity Meters IEC INDUSTRIAL+COMMERCIAL Landis+Gyr Dialog ZMG310AR/CR TECHNICAL DATA Frequency Nominal Frequency fn 50 or 60 Hz tolerance ± 2 % Mesurement Accuracy Accuracy ZMG310xR active energy
More informationPFXLM4B01 D * * (1) (2) (3) (4)
Model:PFXLM4B01DDK PFXLM4B01DDC PFXLM4B01DAK PFXLM4B01DAC LT4000M Rear module Model Name Indication PFXLM4B01 D * * (1) (2) (3) (4) Notice to our valued customers who use LT4000M series (analog model)
More information38 Series - Relay Interface Modules A
Series - Relay Interface Modules 0.1-2 - 6 A - Relay interface modules for use with PLC systems, mm wide - Sensitive DC coil or AC/DC coil version - Supplied with integral coil - Instant removal of relay
More informationTotalizing Counters mini-i
mini-i Type 634/635 Type 634: Counter with high immunity against magnetic interfere Type 635: Counter with high shock stability Miniature size Low power consumption Electrical connections in standard grid
More informationU1601 ENERGY CONTROL SYSTEM
3-348-844-03 4/8.05 64 processing channels physical inputs or LON meter outputs can be assigned for the calculation of energy, power and costs Energy Control Language for the programming of analysis, monitoring
More informationPLA 33. Power line analyzer. User and service manual. version 2.4
PLA 33 Power line analyzer User and service manual version 2.4 Content. Front control panel and terminal plate...3 7.2.2. System frequency setting...0 2. Device description...4 7.2.3. Password protection...0
More informationAnalog Digital Multimeter with Insulation Resistance Measurement
RISH MIT 30 Product Features: RISH MIT 30 is Analog Digital Multimeter with insulation resistance measurement, which measures VAC, VDC, VAC+DC,Frequency, ma DC, ma AC+DC,Resistance, continuity, Diode,
More informationMID. Energy Management Energy Analyzer Type EM Product Description. How to order EM26 96 AV5 3 H O3 S1 PF A. Type Selection EM26 96
Energy Management Energy Analyzer Type EM26 96 M-bus communication by means of VMU-B adapter Application adaptable display and programming procedure (Easyprog function) Easy connections management Certified
More informationNOVOHALL Rotary Sensor non-contacting. Series RSC-2800
NOVOHALL Rotary Sensor non-contacting Series RSC-2800 Special features Non-contacting, magnetic technology Measuring range up to 360 Available with push-on coupling or marked shaft Simple mounting Protection
More informationElectronic timer CT-AWS Impulse-OFF with 1 c/o contact Data sheet
2CDC 251 121 F0004 1 5 2 4 3 6 Characteristics Single-function impulse-off timer One device includes 10 time ranges, from 0.05 s to 300 h, for the adjustment of the pulse time Remote potentiometer connection
More informationVert-X 31E - 5V / % Ub. Applications Concrete pump Access control system Fork lift
Sensor principle MH-C MH-C2 Electrical data Measuring range 0... 360 0... 360 Indep. linearity (typ.) % of meas. range ±0.3 ±0.3 Max. hysteresis 0.1 0.1 Resolution bit 12 14 Max. repeatability 0.1 0.1
More information02/11/2015
17.5 mm - 1 Relay 5A EMER8 Part number 88829198 Multifunction or mono-function Multi-range (7 ranges) Multi-voltage or single voltage Screw terminals LED status indicator (1 voltage present LED, 1 timer
More informationENA33LCD. Power line analyzer. User and service manual. Obrezija 5 SI-1411 Izlake
ENA33LCD Power line analyzer User and service manual version 2.9 (FW version 6.8 and newer) ETI, d.o.o. Obrezija 5 SI-1411 Izlake www.etigroup.eu/products-services 1. Front control panel and terminal plate
More informationENERGY-0-RS. Energy Meter. User manual
ENEGY-0-S Energy Meter User manual Index 1 Safety guide lines...4 2 Model identification...4 3 Technical data...4 3.1 Main features...4 3.2 Hardware and software features...4 4 Dimensions and Installation...6
More informationVert-X 22E - 5V / PWM. Applications Wind vanes Valve control Level sensor Special purpose vehicles
Sensor principle MH-C MH-C2 Electrical data Measuring range 0... 360 - Indep. linearitiy (without misalignment) % of meas. range ±0.3 - Indep. linearitiy (with allowed misalignment @ 360 ) % of meas. range
More informationProgrammable AC Current Transducer MT418
Programmable AC Current Transducer MT418 RMS AC current measurements Current auto range measurements up to 12 A Frequency measurement range 16 400 Hz AC or universal wide auiliary power supply range 24
More informationElectronic timer CT-TGD.22
2CDC 251 097 F0t06 a Rotary switch for the preselection of the time range of the ON time b Potentiometer with direct reading scale for the fine adjustment of the ON time c Rotary switch for the preselection
More informationHigh precision measurement system for current and voltage IHC-A/B-RM01/03
Measurement Offset-free and low-noise 16 bit data acquisition system ISA-ASIC Internal sample rate 3,500 Hz Communication Standard RS232- or RS485 interface Advantages Direct measurement on the bus bar
More informationDELTAplus. DIN Rail Mounted electricity meters. Technical Documentation
DIN Rail Mounted electricity meters Technical Documentation Table of Contents DELTAplus General Description... 4 Chapter 1: Assortment... 5 Assortment Direct connected meters... 6 Assortment Transformer
More informationTechnical Specification
LARGEST RANGE OF IMPULSE TESTERS UP TO 100KV/100KA Technical Specification E-MIG1203CWG revised: 22. June 2003 1 MIG Tester Type MIG1203CWG 1 MIG Tester Type MIG1203CWG 1 1.1 Introduction 1 2 General 2
More informationVert-X 27E - 5V / % Ub. Applications Harvesting machine Fork lift Hydraulic pump
Sensor principle MH-C MH-C2 Electrical data Measuring range 0... 360 0... 360 Indep. linearitiy (without misalignment) % of meas. range ±0.3 ±0.3 Indep. linearitiy (with allowed misalignment @ 360 ) %
More informationElectronic timer CT-SDD.22
CDC 099 F0t0 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied W
More informationVert-X 37E - 5V / % Ub. Applications Agricultural machines Construction machines Forest machines Special purpose vehicles
Sensor principle Electrical data Measuring range 0... 360 0... 360 Indep. linearitiy (without misalignment) % of meas. range ±0.3 ±0.3 Indep. linearitiy (with allowed misalignment @ 360 ) % of meas. range
More informationE35C. AD-FG/CG/GG Version 3.2. Technical Data. Communication Module Residential
Communication Module Residential AD-FG/CG/GG Version 3.2 E35C Technical Data E35C AD-xG Version 3.2 communication modules provide GPRS/GSM communication between E35 meters and a central system. Up to four
More informationNI REM Remote I/O Overview DATASHEET. Temperature Input Module for Remote I/O
DATASHEET NI REM-11120 Temperature Input Module for Remote I/O 4 thermocouple channels with input range of ±100 mv 1 voltage input channel with range of ±5V 24-bit resolution Optional external CJC or additional
More informationMeasuring Transducer MT4xx series Programmable AC Current Transducer MT418
Measuring Transducer MT4xx series Programmable AC Current Transducer MT418 o RMS AC current or frequency measurements o Current auto range measurements up to 12 A o Frequency measurement range 16 400 Hz
More informationEnergy Management Energy Analyzer Type EM210 MID
Energy Management Energy Analyzer Type Multi-use housing: for both DIN-rail and panel mounting applications MID annex MI-003 (Measuring Instruments Directive) compliant Class B (kwh) according to EN50470-3
More information7E Series - Energy meter. Features PTB 1
Features kwh Energy meter - 1-phase Type 7E.13 5(32) - 1 module wide Type 7E.16 10(65) - 2 module wide Complies with E 62053-21 and pre 50470 Complies with the EU MID-directive 2004/22/EG (Measuring Instruments
More informationWIRELESS MODBUS GATEWAY WGW410
WIRELESS MODBUS GATEWAY WGW410 The Tekon Wireless Modbus Gateway WGW410 is specifically designed to meet the most rigorous requirements of operation in the industrial process environments. Due to their
More informationEnergy Management Energy Analyzer Type EM112
Energy Management Energy Analyzer Type EM112 Single phase energy analyzer Class 1 (kwh according to EN62053-21 Class B (kwh according to EN50470-3 Accuracy ±0.5% RDG (current/voltage Direct current measurement
More informationDigital Panel Meters DC/AC Current and Voltage Indicator/Controller Type LDM40
Digital Panel Meters Current and Voltage Indicator/Controller Type LDM40 Multi-input instrument 4-DGT LED 0.1% RDG basic accuracy TRMS AC current and voltage measurements AC/DC current measurements: selectable
More informationSAMSUNG ELECTRO-MECHANICS CO., LTD
Model Name : Features : ㅡ Suitable for LED lighting application ㅡ UL8750, UL1310 Class 2 ㅡ For use in Dry and Damp Location ㅡ Full-protection provided: OCP/OVP/OTP/SCP ㅡ 0-10V Dimming Control ㅡ IP67 ㅡ
More informationAnalogue temperature controllers
Analogue temperature controllers CT8A Input by J-K thermo-couple or by thermo-resistance Pt 00 (-wire) regulation modes : ON/OFF or proportional derivative selected by wiring Relay output Specifications
More informationMINI MCR-SL-UI-f(-SP)
Configurable Analog Frequency Transducer INTERFACE Data Sheet PHOENIX CONTACT - 02/2006 Description The configurable analog frequency transducer MINI MCR-SL-UI-f(-SP) is used to convert analog standard
More informationTechnical Specification
LARGEST RANGE OF IMPULSE TESTERS UP TO 100KV/100KA Technical Specification No. E-MIG0603IN2.doc revised: 20.October 2004 1 MIG Tester Type MIG0603IN2 1 MIG Tester Type MIG0603IN2 1 1.1 Introduction 1 2
More informationVert-X 27E - 24V / SPI. Applications Harvesting machine Fork lift Hydraulic pump
Sensor principle MH-C MH-C2 Electrical data Measuring range 0... 360 - Indep. linearitiy (without misalignment) % of meas. range ±0.3 - Indep. linearitiy (with allowed misalignment @ 360 ) % of meas. range
More informationVert-X 31E - 24V / SPI. Applications Concrete pump Access control system Fork lift
Sensor principle MH-C MH-C2 Electrical data Measuring range 0... 360 - Indep. linearity (typ.) % of meas. range ±0.3 - Max. hysteresis 0.1 - Resolution bit 14 - Max. repeatability 0.1 - Sample rate fast
More information