METERSUK. SmartLink D Y N A M i T E. EM415 MOD Series. User Manual KEY FEATURES INDEX 3. TECHNICAL DESCRIPTION. Single Phase Metering

Size: px

Start display at page:

Download "METERSUK. SmartLink D Y N A M i T E. EM415 MOD Series. User Manual KEY FEATURES INDEX 3. TECHNICAL DESCRIPTION. Single Phase Metering"

Eric Bishop
5 years ago
Views:

METERSUK LTD s a l e s @ m e t e r s. c o.

1 METERSUK LTD s a l e m e t e r s. c o. u k Series Smart Energy Meter KEY FEATURES Single Phase Metering Single phase metering 4 din modules, Standard DIN rail Format (DIN43880) EN Class B Energy consumption LED, reverse current LED, Communication LED Isolate pulse output (DIN43864) LCD display, 6 integer 1 decimal backlight display Internal transformer Direct metering up to 100A Smart communication port, Standard, Modbus or M-bus version is available. Program by button on the nameplate or via communications Memory back-up (EEprom) MID approval The meter is intended to be installed in a Mechanical Environment M1, with Shock and Vibrations of low significance, as per 2004/22/EC Directive and should be installed in Electromagnetic Environment E2, as per 2004/22/EC Directive. Mod SmartLink D Y N A M i T E INDEX 1. Safety notice 2. Package Contents 3. Technical Description 3.1 Performance Criteria 3.2 Meter Specification 3.3 Basic Errors 4. Dimensions 5. Wiring diagrams 6. Meter reading 7. Main features 7.1 Consumption Indicator 7.2 Reading the Meter 7.3 Pulse Output 7.4 Communication Port 8 Programming 8.1 Password verify 8.2 ID setting 8.3 Baud rate setting 9. Technical support 1. SAFETY NOTICE The smart energy meter of Em415 series does not require special mechanical or electrical tools for its installation. Mounting position (with any angle of tilt) has no effect on the measurement functions of the meter. Connecting of the meter must be made according to applicable wiring diagram. Incorrect connection of the meter to the electricity network causes major display problem and can also causes serious damage to the meter. Before starting meter operation, it must be ensured the local conditions of the energy system are consistent with data on the nameplate of the meter. Preferably use for the connection of shielded cables. Make sure that connecting cables are not damaged during installation of the meter are not energized and free of non-mechanical stress. Repairs when removing the cover of the meter, which is also under tension can be made only by a qualified electrician who is familiar with the associated risks. Capacitors in the meter may still be charged even if the meter is disconnected from all energy sources. 2. PACKAGE CONTENTS Single phase, electronic energy meter instructions for assembly ID setting Baud rate setting Password setting 3. TECHNICAL DESCRIPTION EM415-Mod Modbus SO Output

2 3.1 PERFORMANCE CRITERIA Operating humidity Storage humidity Operating temperature Storage temperature Humidity Accuracy class Protection against penetration of dust and water 75% 95% -25 C to + 55 C -40 C to +70 C 0 to 95%, non-condensing EN & IEC B IP51 Insulating encased meter protective class Connection area main terminals Current terminals flexible 1 mm² another terminal flexible 1 mm² 0-16mm² 0-2.5mm² 3.2 METER SPECIFICATION Voltage(v) 230V Operational voltage 70%-130%Un - Iref 10A -Itr 1A -Imax 100A -Imin 0.5A -Ist 40mA Power consumption of current circuits(va) < 0.01 voltage circuits(w) < 1.3W General data Frequency (Hz) 50 Memory back-up EEprom Environment resistance Terminal 960 to heat and fire Cover 650? upper ABS+PC? lower ABS+PC Pulse output Pulse width(ms) 80 Pulse constant(imp/kwh) 1600 LED constant 1600 WxHxD (mm) 76 x x BASIC ERRORS Value of current Power factor Errors Test pulse number Imin 1 ±1.5% 4 Itr 1 ±1.0% 4 Itr 0.5ind ±1.5% 4 Itr 0.8cap ±1.5% 4 10Itr 1 ±1.0% 8 10 Itr 0.5ind ±1.0% 8 10Itr 0.8cap ±1.0% 8 Imax 1 ±1.0% 12 Imax 0.5ind ±1.0% 12 Imax 0.8cap ±1.0% DIMENSIONS

104.5 100 46 126 44 59 60 SEALING POINTS 5.

3 SEALING POINTS 5. WIRING DIAGRAMS Note: the following types of wiring diagrams show the energy meter, include terminals for pulse output and the communication interface RS-485. However, depending on the ordering number of the energy meter only some terminals of the energy meters are involved. 1 & 2 Phase in & out 3 & 4 Neutral 5 & 6 Rs485 Communication contact TX/RX(-), Terminal 5 TX/RX(+), Terminal 6 (T) G485 Terminal 7 11 & 12 Test pulse output contact (12 11+) 6. METER READING The viewing angle Operator meter should be at 45.

4 7. MAIN FEATURES 7.1 Measuring Function On the EM415 S front panel, there are three LED, respectively, for the Active energy pulse light, current reverse,communication. The constant of the impulse is shown on the nameplate of the meter. The smart energy meter is equipped with 6+1 LCD display, which is used as recording consumption and can t be reset to zero. The number system is based on units of 10. And unit is kwh. Another way through RS485 and PC software or HHU (hand held unit) unit can read power consumption 7.2 Display Function Meters have four status: self-inspection status, cycle display status,button press display and program status. Self-inspection status Full screen display Meter version number CYCLE STATUS Meter display as follows: active energy (8 sec), Modbus id (2sec) active energy: Modbus Id: ID 01 Serial number, Baud rate. Display cycle is 3 seconds. BUTTON PRESS DISPLAY STATUS: Press the "up" and "down" buttons the meter will display Version number, Total energy, Modbus id, High 5 digits Serial number, Low 7 digits serial number, Baud rate, Impulse constant. Without any operation, the meter will enter circle display automatically. Serial number (high 5 bit): Sn= n00000

5 Serial number (low 7 bit): Baud rate: bd 1200 Impulse constant: cf Communication Function RS485 Output Protocol Modbus RTU Data format 8 data bit,even,1 stop bit Baud rate 1200(default),2400,4800,9600 Address range User settable Bus loading 64pcs Cable AWG Pulse output Smart din rail energy meter is equipped with a pulse output which is fully separated from the inside circuit. That generates pulses in proportion to the measured energy. They are test pulse output (pins 11 & 12). Usually, the test pulse output is used as testing accuracy or reading purpose in close quarters. The test pulse output is a polarity dependant, passive transistor output requiring an external voltage source for correct operation. For this external voltage source, the voltage (Ui) should be 5-27V DC, and the maximum input current (Imax) should be 27mA DC. To connect the impulse output, connect 5-27V DC to connector 11 (anode), and the signal wire (S) to connector 12 (cathode). The meter pulses are indicated on the front panel 8. PROGRAMMING By holding the keys SET pressed for at last 3 sec., starts menu programming mode. LCD will show: PA 0000

6 8.1 Password Verify On the smart meter display will appear : PA followed by the currently memorized value. PA means Password, 0000 means the 4 digits of the Password. You can press Page Down button to decrease the input value, and press PageUp to increase the input value. Press the SET button to switch the input Password digits, when the Password is correct, the meter will enter program status and display the ID program interface. Remarks: Please remember well the Password, you can only reset the Password to default (8888) by opening the meter and short connect the CLEAR on PCB board. 8.2 ID Setting After the Password authentication, the meter will display the ID XX setup interface. As the following picture Id 01 it means the current ID address is 01 (the ID address is hex code) ID 01 Press PageDown button to decrease the digits. Press PageUp to increase the digits, press PRO button to save the setup, the interface will switch to Baud rate setup interface automatically. Press PRO button to enter next interface if you do not need to change the baud rate. Remarks: Type meters without communication function do not have the setup interface. 8.3 Baud rate setting bd 1200 Press Pagedown and pageup buttons to select the communication baudrate, press SET button to save the setup. The interface will enter CT setup. Remarks 1. Type Default baudrate will be 1200bps 2. Type Default baudrate will be 2400bps 3. Type Without communication function do not have the setup interface. PASSWORD SETTING PA-8888 The meter will display the current password after enter the password setup interface, press the SET to change the password. Use page down and page up button to input password as you want. After 30 seconds the meter will save the password you changed. Remarks: 1 Do not forget the password you setup. 2 Please press the button to check if every setup is correct after the program. 3 Password setup interface - symbol will blink. 9. TECHNICAL SUPPORT Any questions, please contact: Meters UK s a l e m e t e r s. c o. u k W h i t e L u n d I n d u s t r i a l E s t a t e L a n c a s t e r L A 3 3 B T

METERSUK. SmartLink D Y N A M i T E. EM735 S Series. User Manual KEY FEATURES INDEX 3. TECHNICAL DESCRIPTION.

METERSUK. SmartLink D Y N A M i T E. EM735 S Series. User Manual KEY FEATURES INDEX 3. TECHNICAL DESCRIPTION. LTD METERSUK sales@meters.co.uk 01524 555 929 EM735 S Series Smart Energy Meter KEY FEATURES METERSUK LTD Three phase metering CE Approved Three Phase metering, 7 din Modules Accuracy class 1 according