Thin-Film Cascadable Amplifier 5 to 1000 MHz. Technical Data. UTO/UTC 1005 Series

Transcription

1 Thin-Film Cascadable Amplifier 5 to 1000 MHz Technical Data UTO/UTC 1005 Series Features Frequency Range: 5 to 1000 MHz High Dynamic Range High Output Power: m (Typ) Noise Figure: 5.0 (Typ) Temperature Compensated Surface Mount Option Applications IF/RF Amplification Output Stage Surface Mount Assembly Description The 1005 Series is a medium-gain, thinfilm bipolar RF amplifier using resistive feedback and active bias for stability over temperature and bias variations. Inductive networks maintain good VSWR while the RF is coupled through input and output blocking capacitors. The 1005 Series amplifiers are available in three packages: the surface mount hermetic PP-8 (.75 in. x.75 in.) case, the TO- 8 hermetic case and the connectorized TC-1A case. Pin Configuration UTOTO-8T UTCTC-1A CASE Schematic V+ Maximum Ratings Parameter Maximum DC Voltage Continuous RF Input Power Operating Case Temperature Storage Temperature R Series Burn-In Temperature +17 Volts +15 m 55 to +115 C 62 to +150 C +115 C Thermal Characteristics 1 θ JC Active Transistor Power Dissipation 75 C/W 1 mw Junction Temperature Above Case Temperature 1 C MTBF (MIL-HDBK-217E, A 90 C) 98,52 Hrs. Weight: (typical) UTO2.1 grams; UTC21.5 grams

2 2 Electrical Specifications (Measured in 50 Ω +15 VDC nominal unless otherwise noted) Typical Guaranteed Specifications Symbol Characteristic T C = 25 C T C = 0 to 50 C T C = 55 to +85 C BW GP NF P1 IP IP2 HP2 ID Frequency Range Small Signal Gain (Min.) Gain Flatness (Max.) Noise Figure (Max.) Power +1 Comp. (Min.) Input VSWR (Max.) Output VSWR (Max.) Two Tone rd Order Intercept Point Two Tone 2nd Order Intercept Point One Tone 2nd Harmonic Intercept Point DC Current 12.6 ± <1.:1 <1.: ± ± Unit MHz m m m m ma Typical Performance Over Temperature (@ +15 VDC unless otherwise noted) Key: +25 C +85 C -55 C Gain, Gain Noise Figure, 6 5 Noise Figure Power 1 Gain Compression, m Power Output Input VSWR Output VSWR VSWR VSWR IP, m Third-Order Intercept Point Second-Order Intercept Point Second-Harmonic Intercept Point IP 2, m HP 2, m 50 0

3 Automatic Network Analyzer Measurements Numerical Readings (Typical production +25 C ambient) Bias = Volts FREQUENCY VSWR GAIN PHASE PHASE GROUP DELAY VSWR ISOLATION MHz IN DEGREES DEV ns OUT LINEARIZATION RANGE: to MHz S-Parameters Bias = Volts FREQUENCY S 11 S 21 S 12 S 22 MHz Mag Ang Ang Ang Mag Ang

4 Product Options UTO 509R Model Number Prefix UTO- UTM- PPA- Model Number Screening Option Blank = No Screening R = R-Series Screening For more information on R-Series screening, see Reliability Screening, Pub E. UTC Model Number Prefix UTC- Model Number Connector Option For TC-1A case the only connector option available is the -1. The -1 option consists of a SMA Female connector on both the input and output (see note). Note: R-Series screening is not available in the TC-1A case as the case is non-hermetic. Case Drawings TO-8T DIA.50 DIA MAX GLASS RING.060 DIA (X) 5.01 CASE ±0.015 APPROXIMATE WEIGHT 2.1 GRAMS NOTES (UNLESS OTHERWISE SPECIFIED): 1. DIMENSIONS ARE SPECIFIED IN INCHES 2. TOLERANCES: xx ±.02 xxx ±.010

5 Case Drawings 0.50 TC-1A 0.06 CONTROL IN (WHEN REQUIRED) POWER PUT PUT SMA JACKS 2 PLACES X DRILL & TAP FOR 2-56 SCREW, DP ICAL WEIGHT WITH CONNECTORS = 21.5 GRAMS NOTES: 1. THE TC-1A CASE IS A NON-HERMETIC CASE. 2. THE ONLY CONNECTOR OPTION AVAILABLE FOR THE TC-1A CASE IS THE 1, SMA FEMALE CONNECTORS AT BOTH INPUT AND OUTPUT PORTS. NOTES (UNLESS OTHERWISE SPECIFIED): 1. DIMENSIONS ARE SPECIFIED IN INCHES 2. TOLERANCES: xx ±.02 xxx ±.010 Contact Teledyne Microwave Solutions: fax Check for updates: