Applications QK-W015. Features. Sockets. Smart House. Plant Maintenance Valve Control Pumping Station Security Systems PLC. 1 of 13 V1.

Transcription

1 QK-W015 WiFi Remotee Controller Application Notes Features Turn Electronics ON or OFF from anywhere through internet Remote Control from 50 Meters with WiFi Android, ios App & Application for Windows platform Instant Set Up Up to 10 Mobiles Phones per Unit Switching Electronics Devices through Relays or 433MHz RF Main Sockets Master ON/OFF Turn Everything on with One Click Support both Ad-hoc and Station Mode UK, Europe & USA RF Power Sockets Available Applications Control Lighting, Electrical Appliance Smart House Automation Application Remote Maintenance Irrigation Systems Plant Maintenance Valve Control Pumping Station Security Systems PLC and Automation System 1 of 13

2 Document History Issue Date Changes / Comments Initial release New hardware release Order Information Part No Description QK-W015 WiFi Remote controller (only three relays output, no RF 433MHz module plug sockets) and RF QK-W015EU QK-W015US QK-W015UK QK-W015 with three RF 433MHz UK type main sockets QK-W015 with three RF 433MHz Europe type main sockets QK-W015 with three RF 433MHz USA type main sockets Contents 1 INTRODUCTION SETUP POWER.2 ACCESS 3 AD-HOC MODE R UP... 3 S QK-W CONNECT WITH MOBILE PHONES of 13

3 3..2 RENAME THE PORT. 4 STATION (INFRASTRUCTURE) MODE STATION MODE SETTING THROUGH.2 SWITCHING TO STATION MODE....3 RESET H APP PARING WITH RF POWER SOCKETS APP(ANDROID VERSION) HARDWARE CONNECTIONS RF MAIN SOCKETS ENCLOSURE OPERATING SPECIFICATIONS INTRODUCTION QK-W015 series remote controller is a versatile device which can be attached to many of electronic devices in homes, offices, plants, or wherever you need. Operators can control any remote equipments, heater, lights, machines, or power sockets from anywhere in the world through internet. QK-W015 support three relay outs and 433MHz RF transmitter. RF power sockets within 50 meters of QK-W015 can be controlled by mobile operators. Figure 1 System diagram (Station mode) 2 SETUP 2.1 Power up QK-W015 remote controller need to be powered by 12VDC voltage. Connect a 12 volt DC power supply to the power socket, switch on the power supply. The blue LED should light up and then flashing slowly. After about 10 seconds, the Red LED willl light up indication system finishes initialization. 3 of 13

4 2.2 Access QK-W015 After QK-W015 finish initialization, operator should be able to scan SSID on the mobile terminals and find a SSID called WiFi168. Access WLAN of the mobile terminal and connect with the WiFi168. The default password is Blue LED will keep light up once the WiFi168 is connected by the operators mobile terminal. If WiFi168 cannot be found, please go to RESET section of this application note following the stepss to reset the module. Figure 2 Search SSID Figure 3 Connect to QK-W015 3 AD-HOC MODE The IEEE has two basic modes of operation: Ad-hoc mode and infrastructure mode(also called station mode). In ad hoc mode, mobile terminals transmitt directly peer-to- point(ap) that serves as a bridge to other networks (such as Internet or LAN). QK-W015 WiFi controller can support in both Ad-hoc and Station mode. peer. While In infrastructure mode, mobile terminals communicate through an access Setting QK-W015 works in Ad-hoc mode is quite straightforward. Once the mobile terminal connected to WiFi168 network, QK-W015 then works in Ad-hoc automatically. 4 of 13

5 Figure 4 Working in Ad-hoc mode Operator can use the following link to download the latest version of Android App to work with QK-W015. /down/class/?3.html Figure 5 Main page of APP 3.1 Connect With Mobile phones Once the WiFi168 is connected, operators can control these electronics devices in Main control panel which have connected on relays and RF main sockets. The indicator icons (the light bulb next to Off button) can demonstrator each relay. Due to one way communication between QK-W01cannot be check and and 433MHz RF main sockets, the status of the RF main sockets indicated. 5 of 13

6 These icons indicate the status of the relays. Figure 6 Indicator of the setting 3.2 Rename the port Operators can rename the three relay outputs and three RF main sockets as meaningful names through settings on App. Figure 7 Rename the port 4 STATION (INFRASTRUCTURE) MODE To control QK-W015 remotely, it should be set working in station mode, operator need perform the following procedure to finish the setting. 1,Press and hold the Reset button, then power up QK-W015. The blue LED will light up for few seconds, then the red LED turns on. Keep the red LED turns on for 3 seconds, release Reset button. 6 of 13

7 2, Wait for 60 seconds, red LED turns off and then turns on again. During this period, blue LED blinking every second interval. 3, Operator can now use the mobile terminal search and connect WiFi168. 4, Once this Ad-hoc connection has been setup, operator can start the following setting through APP. SSID name ---- Input the SSID name(or called AP name) which QK-W015 will access to. Password --- Input the password for accessing AP. Quark-elec notices for some old type Access Point, they maybe have connection problem with QK-W015 if the AP security type set as WEP. So, if operator has the access problem, please change the security type to WPA or WPA2, avoiding WEP on the wireless router. IP address --- Dynamic IP address will be assigned by QK-W015 if operator don t set a static IP address on APP. 5, Re-power up QK-W015 to apply the remotee control function. 4.1 Station mode setting through APPP Operator should make sure QK-W015 has connected with the mobile terminal in ad-hoc mode before the following setting. Run the APP, click Station mode setting, input SSID of the AP and then Save. The red LED will turn off. Keep waiting until the responsee messagee received from QK-W015. Then the same way applies for setting the password. It is recommended that operator don t set static IP address to QK-W015 if static IP address has to be used. 7 of 13

8 Figure 8 Station mode setting 4.2 Switching to station mode Once the above setting finished, operator can click Switch to station mode to set QKis busy. W015 working in station mode. After click Switch to station mode, the red LED light will turn off indicating system Waiting about 90 seconds, the blue LED will turns off. Another 30 seconds, the red LED light turn on firstly and then the blue LED. If the SSID or password is not correct, then the blue LED will keep blink. In this case, operator should reset the module and repeat the setting procedure again. Once QK-W015 has successfully connected with the AP in station mode, operatorr should re-powerr up QK-W015 to get the full function applied (don t press the reset button during the re-power process). 8 of 13

9 Figure 9 Switch to station mode 4.3 Reset Operator can always reset QK-W015 if the setting is incorrect or would like to switch the working mode. Following below steps to reset QK-W015 to the factory settings: 1, Power off QK-W015. 2, Press and hold the Reset button, then power up QK-W015. Blue LED will light up for few seconds, then the red LED turns on. Keep the red LED turns on for 3 seconds, release Reset button. 3, Wait for 60 seconds, the red LED turns off and then turns on again. During this period, the blue LED is blinking every second. 4, Operator can now available to connect to WiFi PARING WITH RF POWER SOCKETS QK-W015 has a build-in 433Mhz RF transmitter module. It can pair with up to four RF power sockets. So the operators are able to turn ON/OFFF the electrical devices by switching the power sockets. The power sockets have been paired and ready to use if they come with QK-W015. However the operator can always pair or releasee the pairing by following steps: Insert the RF power socket into a powered mains wall socket. The LED light on the socket should flash at 1 second intervals indicating it s ready to pair with the QK-W015. If the lights doesn t flash, presss and hold the ON/OFF button for 5 seconds to clear the memory indicated by the quickly flashing LED. Open WiFi Remote control panel in App, press the corresponding RF switch ON button. The paring command will be sending out through RF signals. 9 of 13

10 Figure 10 RF Switch ON buttons Once the power socket received the paring command, The LED light on the socket will flash briefly more quickly and then flash at 1 second intervals. This RF main socket should have been successfully paired now. Repeat above process for each different RF main sockets. Simply plug-in the appliance which you want to operate remotely into the socket, press the corresponding ON button on App that is paired to the socket. The appliance will turn on. 6 APP(ANDR OID VERSION) The latest version of Android APP can be downloading with the following link: /down/class/?3.html Once the mobile phone has connected with QK-W015, the operator can control these electronics devices which connected on relays and RF main sockets. And the operator can check the relays status by click Check relays status. 7 HARDWARE 7.1 Connections General view of the module is show as below and details of each connectionn are described on it. QK-W015 use 12VDC 1.0Amp power. The outside and inner diameter of the plug is 5.5mm and 2.1mm. 10 of 13

11 RF 433MHz aerial LED2 LED1 12V Reset NO1 COM1 NC1 NO2 COM2 NC2 NO3 COM3 NC3 Figure 11 mechanical drawing 7.2 RF main sockets Customer can select USA, European or UK type RF main sockets. Quark-elec standardd RF main sockets support Watts power rating. Although QK-W015 have running specific algorithm to increasee the RF transmission reliability, Quark-elec cannot guarantee 100% of proper action rate of RF main sockets. QK-W015 RF signal could be affect by other nearby RF devices such as bell ring, car key, cordless phone, mobile phone, RF alarm system. The following is a real test result taken in a house environment in the UK. Distance between QK-W Mhz RF main sockets and Properr action rate (RF main sockets been successfully trigged by QK-W015) 2 meters 100.0% 5 meters 100.0% 11 of 13

12 8 meters 99.2% 10 meters 98.1% 15 meters 95.4% 20 meters 93.7% 7.3 Enclosure IP56 Insulation Class 2 plastic enclosure, 115mm* 90*40 external dimension is used for QK- W013. Figure 12 Enclosure drawing 8 OPERATING SPECIFICATIONS Item Specification Operating Temperature Storage Temperaturee DC Supply Average Supply Current (typical quiescent) -25 C to +80 C -40 C to +85 C 12.0V(+/-10%) 160mA Supply Current in Busy Period(data 190mA transmission) WLAN Standard IEEE b/g/n 12 of 13

13 Operating Frequency Receive Sensitivity Transmit Mean Outpu Power WiFi Antenna Encryption 433Mhz Transmitting Power 433Mhz Modulation Mode RF Transmission Power RF Emission Distance Rated Current on Relay Rated Voltage on Relay to GHz Mbps, Mbps +17 dbm for b, +13 dbm for g, +12 dbm for n Build-in module U.FL antenna connector Support for WEP40/64, WEP104/128, WPA-PSK, WPA2- PSK, AES and TKIP 1W ASK (AM) <10mW 25 to 50 meters (open air condition) 7A240VAC 90V-245V Power rating on RF main socketss < 2000 W Please feel free to order our products from our onlinemall: /onlinemall/ technical information and enquires please go to Quark-elec forum: For sales and purchasing information, please us: info@quark-elec.com For more Quark Electronics (UK) 24 Meadowbank,Hitchin Herts. UK SG4 0HY 13 of 13