Gate control mts2000/02 R2.8

Transcription

1 Control system Gate control mts2000/02 R2.8

2 I Table of contents 1 Conformities 1.1 Guidelines and standards CE mark General safety information 2.1 Explanation of symbols used to provide safety information Information regarding the safety information Permissible users Correct handling Basic information 3.1 Warranty and liability Purchaser obligation User obligation Correct use Improper use Instructions concerning EMC protection Description of product 4.1 Safety concept Safety equipment independent of the processor Monitored safety equipment Scope Overview of operating modes Interfaces for input elements Interfaces for output elements Structure Operating modes Impulse control as sequence control Impulse control, defined up down Single/dual lane feedback control with light control and automatic closing Special operating modes Manual mode Emergency control Functions Continuously open switch ("gatekeeper s switch") / external clock Weekly indexing clock Halt key The safety equipment Closing edge protection Stop in open + closed position (protection against anything being snagged and pulled in) Stop in closed position (passage protection) Process of re-opening after triggering during closing 4-10 meißner gate systems Gate control operating manual mts2000/02

3 Table of contents I Hold open time Extending the hold open time Shortening the hold open time Run time monitoring Technical data Electrical data Mains connection Stop switch Impulse sensor connections Interfaces for safety equipment Connection for potential-free contact Connection for lights Connection for drive Device protection Mechanical data Ambient conditions Assembly and installation 5.1 Safety information regarding assembly Fitting gate control mts2000/ Electrical connection Start-up and operation 6.1 Programming gate control mts2000/ Controls of gate control mts2000/ Hardware settings Function of keys Menu structure of operating software Language setting Program gate Service Operation Assembly instructions for weekly time switching clock mts2000/02 (not in standard version) Assembly Programming Operating instructions for radio mts2000/02 (not in standard version) Assembly Setting instructions Coding table Displays Maintenance & service 7.1 Troubleshooting tool Troubleshooting 7-1 Gate control operating manual mts2000/02 meißner gate systems

4 I Table of contents Testing Fault rectification Control PCB measurement points Regular testing Address of manufacturer 7-6 meißner gate systems Gate control operating manual mts2000/02

5

6 1 Conformities 1.1 Guidelines and standards Device name: Gate control mts2000/02 Guidelines and standards: EMC 89/336/EEC: European guideline regulation on the electromagnetic compatibility (EMC) of electrical equipment VDE 0100: Guidelines for setting up high power systems of up to 1000V VDE 0105: Operating high power systems EN 60204: Electrical systems with electronics operating equipment VDE 0160: Equipping high power systems and electric operating equipment VDE 0700: Safety of electrical devices for domestic consumption etc. BGVA2: Electrical systems and operating equipment BGR 232: Guidelines for power-assisted windows, doors and gates Note The gate control system has been produced and inspected (TÜV Bau und Betriebstechnik GmbH, corporate group for southern Germany in Filderstadt) in accordance with the standards and guidelines listed and was in perfect condition in terms of technical safety when leaving the factory. 1.2 CE mark Gate control mts2000/02 corresponds to the fundamental requirements of the relevant directive (EMC 89/336/EEC, dated 3 May 1989) of the Council of the European Union. Conformity has been proven and he corresponding documents (declaration) are archived by the manufacturer. meißner gate systems 1-1 Gate control operating manual mts2000/02

7 General safety information Explanation of symbols used to provide safety information The following symbols are used in these instructions for use to provide the user with safety information: This symbol identifies a direct threat of danger to the health or even life of people. Failure to follow these instructions can endanger life and limb, resulting in anything from serious damage to health to life-threatening injuries. This symbol identifies a risk of injury to the device user. This symbol identifies important instructions on correct use of the device. Failure to follow these instructions can result in malfunctions on the device. Note This symbol identifies tips for application and particularly useful information which will help you to make the most of all the device s functions. Liability exclusion: This symbol indicates that operator error or failure on the part of the operator to follow certain instructions can give rise to the manufacturer s liability cover being rendered null and void. Instructions for disposal: Ship used devices to an authorised recycling plant (separated into metals, plastics etc.) Information regarding the safety information The safety instructions in these instructions for use MUST be noted and followed. Gate control operating manual mts2000/ meißner gate systems

8 2 General safety information 2.2 Permissible users Only trained electricians may work on the electrical systems. They must assess the work assigned to them, recognise any sources of possible risk and be able to take appropriate safety measures. 2.3 Correct handling In order to keep the device in perfect condition from a technical safety standpoint and to be able to assure safe operation, the user undertakes to comply with the points listed in this operating manual. Operation of the control unit is only permitted while its covers and guards are all in position. Ensure that all gaskets and screw connections are properly secured. meißner gate systems 2-2 Gate control operating manual mts2000/02

9 Basic information Warranty and liability To be assured of success, warranty claims must be predicated on correct and appropriate operation and handling. The manufacturer provides an assurance that all parts are free of material and machining defects at the time of delivery. Liability exclusion: The manufacturer assumes no liability for damage which is caused by operating errors and/or failure to comply with the operating instructions or a failure to carry out maintenance or servicing. 3.2 Purchaser obligation The purchaser must ensure that users are trained in the operation and all safetyrelated aspects of gate control mts2000/02. A report should be produced by all training course attendees documenting the training they have received and this report should be kept on file. Liability exclusion: The manufacturer assumes no liability for damage resulting from any failure by the purchaser to comply with the purchaser s obligations. The purchaser undertakes to only allow trained groups of people to work with the device. The purchaser is also responsible for ensuring that the operating instructions for gate control mts2000/02 are available to the group of users when working with the device. 3.3 User obligation All users must confirm in writing to the purchaser that they have read and understood the safety information and operating instructions. If errors occur as a result of incorrect operations, the user will be deemed to have been responsible. 3.4 Correct use Gate control mts2000/02 is fitted in line with state-of-the-art technology and the recognised rules governing safety with technical equipment. Gate control mts2000/02 should only be used to activate gates which are driven using three-phase motors with reversal inhibit protection and limit switches or AC / DC motors with limit switches when in perfectly safe technical condition. Correct usage also includes: observing all instructions in the operating instructions Gate control operating manual mts2000/ meißner gate systems

10 3 Basic information 3.5 Improper use Incorrect or improper use of the device can put the life and limb of the user at risk, inflict injury on the user and damage the device and/or other material assets. Liability exclusion: The manufacturer assumes no liability for damage caused by improper use. 3.6 Instructions concerning EMC protection The controller has been manufactured and tested in accordance with the corresponding guidelines for EMC (see Section 1.2 CE marking). However, it is possible that mains voltage peaks (due to non-emc compatible loads, for example) may cause the processor to switch off. This procedure is intentional and in no way affects the controller s safety functions. The processor restarts automatically thereafter and the controller is set to Ready mode. The programme sequence can be restarted via the emission of a pulse. These voltage peaks can be suppressed on-site (e.g. by inserting a mains filter as close as possible to terminals 43 and 44, or by taking similar measures). meißner gate systems 3-2 Gate control operating manual mts2000/02

11 Description of product Safety concept Safety equipment independent of the processor All safety-related parts are incorporated in the safety chain (sensors and actuators) directly and independently of the microprocessor. The integrated microprocessor registers and reports from the results of the safety monitoring process, but is not able to influence the safety measures triggered with the exception of reversing the closing edge. The possibility of uncontrolled gate movement triggered by the microprocessor is therefore ruled out and is prohibited by the hardware Monitored safety equipment The evaluation of all safety equipment corresponds to the standard set by the mechanical engineering industry: 1. Before every gate movement, the gate s function is checked automatically. 2. If this function check produces an error, the system is shifted into error status (red light(s) flash(es), if fitted). 3. The gate system cannot be started if an error is present. Normal operations can only be continued once the cause of the error has been rectified. Gate control operating manual mts2000/ meißner gate systems

12 4 Description of product 4.2 Scope Gate control mts2000/02 can be used wherever a high degree of flexibility and complexity is needed. It is used to activate the gates, refer to Chapter 3.4 (Correct use) The operating modes are programmed via a removable display / keypad module Overview of operating modes Impulse control Single/dual lane feedback control with light control and automatic closing Manual mode (with safety functions) Emergency actuation (without safety functions) For more information, refer to Chap.4.4 Operating modes Interfaces for input elements The following external input elements can be connected up, e.g. as impulse sensors: one or two command radio with/without antenna (optional plug-in module) pushbuttons pull buttons key-operated keys continuously open switch ("gatekeeper s switch") Interfaces for output elements The following external output elements can be connected up to the gate control: external lighting for stairways and garages, activation for ventilation or fault message (contact is open in the event of a fault or fall in voltage) lights meißner gate systems 4-2 Gate control operating manual mts2000/02

13 Description of product Structure The gate control is housed in a robust industrial housing of safety class IP54 with the dimensions 250 x 160 x 127 mm. The function group consists of two PCBs: connection PCB control PCB removable display PCB with programming keys Firstly, release plug from connection X1, then remove PCB and bolts The operating and fault statuses appear on the LCD display on the control PCB. Fig. 4 1 Control PCB with controls Gate control operating manual mts2000/ meißner gate systems

14 4 Description of product Supply lines are guided into the housing via screw connections. Apertures which are not used must be sealed with blind plugs. meißner gate systems 4-4 Gate control operating manual mts2000/02

15 Description of product Operating modes Impulse control as sequence control Function: Opening and closing the gate system after activation taking the safety equipment and if necessary the pre-warning time setting into consideration. Details: impulse sequence Activation from either: internal + key radio triggers the following function: motion status of gate changes in the following sequence: OPEN STOP CLOSED STOP If the gate is in its upper or lower limit position, the STOP status is jumped Impulse control, defined up - down Function: 1. Opening and closing the gate system after activation taking the safety equipment and if necessary the pre-warning time set into consideration. Details: Activation from either: impulse for open impulse for close internal + / - keys radio 2 commands triggers the following function: the gate opens or closes. Gate control operating manual mts2000/ meißner gate systems

16 4 Description of product Single/dual lane feedback control with light control and automatic closing Function: 1. Opening the gate system after activation taking the safety equipment into consideration. 2. Closing the gate system once the hold open time and if necessary the prewarning time has lapsed taking the safety equipment into consideration. 3. Light control depending on the occurrence of signals at the inputs for impulse inside, impulse outside or two channel radio. Details: impulse inside Activation from either: impulse outside internal + / - key radio Note triggers the following function: the gate opens. The direction of travel is approved using lights depending on gate control activation (triggering from inside or outside). In the event of alternating activation (triggering from inside or outside) within the hold open time, the direction of travel is changed over using the lights after a pre-warning time which may be set if necessary. The gate shuts automatically once the hold open time and if necessary the prewarning time has lapsed. If selected, the superordinate special operating mode of continuously open (clock) is undertaken in preference to the single/dual lane feedback control with light control Special operating modes: Manual mode Note Function: Opening and closing the gate system taking the safety equipment into consideration. Details: The gate opens or closes for as long as the internal + or keys are pressed. This mode is used for start-up as well as other functions. meißner gate systems 4-6 Gate control operating manual mts2000/02

17 Description of product Emergency control Function: Opening and closing the gate system regardless of the control system s operating mode. Details: The gate opens or closes for as long as the emergency control switches connected up externally or internally are pressed (refer to Fig. 4-1 Control PCB with controls). These switches have a direct impact on the drive. The safety equipment fitted is bridged. Operations without the control PCB attached are possible using the external emergency control switches. For reasons associated with safety, the operator must be able to fully view the gate when pressing the emergency control switch. Care must be taken to ensure that emergency control does not cause damage to the gate and/or does not put people at risk. Note We would recommend using a key-operated switch as the external switch. Gate control operating manual mts2000/ meißner gate systems

18 4 Description of product 4.5 Functions Continuously open switch ("gatekeeper s switch") / external clock Any locking switch can be fitted on site as the continuously open switch. The continuously open function takes priority over all other operating functions; i.e. live processes are interrupted and the gate switches into continuously open mode Weekly indexing clock Function: Holding the gate open and closed at defined times of the day. Details: The weekly indexing clock (which can be retrofitted) controls up to 8 openingclosing cycles per day of the week. The switching times of the week days can be programmed individually or as a group. If the gate is opened, the traffic is control by the light functions. When the gate is closed, the single/dual lane feedback control system is operated by: Activation from either: impulse inside impulse outside internal + key radio Note For more information, please note the operating instructions for the clock, refer to Chapter 6.2 If selected, the superordinate special operating mode of continuously open (clock) is undertaken in preference to programming the weekly indexing clock Halt key A key with a make and break contact can be fitted on-site. The halt function takes preference over all other operating functions; i.e. live processes are interrupted. meißner gate systems 4-8 Gate control operating manual mts2000/02

19 Description of product The safety equipment Closing edge protection Function: Opening and/or reversing the gate once the safety equipment has been activated during the closing process. Details: When the main closing edge protection is triggered during the closing process, the gate either opens to its limit position or reverses for 1 sec. and remains in this position. When at 2 sec. before the lower limit position, only reversing is possible (preset). If the main closing edge is activated, the control system undertakes a total of 3 attempts to close before a fault is displayed. The fault status is reported by rapid fault flashing of the lights, if connected up (also refer to option for the re-opening process described in Chapter "Program gate" 6.1.3). The following can be connected up: optical system OS12 optical system OSE resistance strip R = 8.2 K Note The function of the closing edge protection is checked before every gate movement. Configuration is undertaken via jumper J1 on the control system PCB Stop in open + closed position (protection against anything being drawn in) Note Function: Stop after activation during opening and closing. Details: When triggered regardless of the gate status the gate system is shifted into stop mode. This fault status is reported by the lights fault flashing. Connections are available for one system protecting from anything being drawn in on both the inside and outside. For assembly arrangements, refer to Fig. 4-2 The function of this safety equipment is checked before every gate movement. Precondition: use of one-way light barriers (separate transmitter and receiver). A reflection light barrier can also be connected up but this does not comply with the safety rulings! Gate control operating manual mts2000/ meißner gate systems

20 4 Description of product Stop in closed position (passage protection) Process of re-opening after triggering during closing. During the closing process, the gate will open to its limit position if the passage protection is triggered. Note This applies to all operating modes Hold open time If the function is set to NO for "Reset hold open time via passage protection (also refer to option for "RESET O TIME VIA PP" in Chapter "Program gate" 6.1.4), the time expires despite the passage protection being triggered. Note This applies to the single lane and dual lane feedback control operating modes Extending the hold open time The hold open time is restarted by triggering the passage protection before the hold open time lapses after opening the gate and reaching the top limit position. The hold open time can be set to anything between 1 and 600 seconds. Note This applies to the single/dual lane feedback control operating modes. meißner gate systems 4-10 Gate control operating manual mts2000/02

21 Description of product Shortening the hold open time With the Hold open briefly function set (also refer to option for "Hold open briefly" in Chapter "Program gate" 6.1.3), the gate is held open longer for the period of the Hold open time brief set when the passage protection is triggered and before the hold open time lapses. The closing process is then initiated. The process is restarted when the gate is next driven through. Note This applies to the single/dual lane and dual lane feedback control operating modes Run time monitoring In addition to the hardware safety equipment, the control system is also fitted with software run time monitoring. If the gate does not reach a limit position as a result of the run time set, the system is transferred into error mode. In other words, red light(s) flash(es), if fitted and gate remains motionless. Gate control operating manual mts2000/ meißner gate systems

22 4 Description of product 4.7 Technical data Electrical data Mains connection Voltage supply (at terminals 43, 44) PE (protective conductor) Block of terminals on housing base Power consumption 230 VAC 230 V AC <15 W Stop switch Stop switch (terminals 1, 2) Halt key (terminals 3, 4) 24 V AC/ 1 A 24 V AC/ 1 A Impulse sensor connections Open key or inside impulse 24 V / 100 ma (key, potential-free contact at terminals 5, 6) Close key or outside impulse 24 V / 100 ma (key, potential-free contact at terminals 7, 8) Key for impulse sequence or switch for continuously open (external clock) 24 V / 100 ma (key, potential-free contact at terminals 9, 10) The line length of the impulse sensor should not exceed 15 m. Longer lines must if necessary be disconnected (e.g. potential-free activation of connection via a relay contact) Interfaces for safety equipment Closing edge protection 12 V / 8.2 kω optical (OSE) terminals 11, 12, 13 electro-mechanical (EMC) terminals 11, 12 Stop in closed position (light barrier, potential-free contact) 24 V / 100 ma Supply for transmitter terminals 16,17 Supply for receiver terminals 16,17 Switching output terminals 14,15 meißner gate systems 4-12 Gate control operating manual mts2000/02

23 Description of product 4 Stop in open + closed positions 1 (light barrier, potential-free contact) 24 V / 100 ma Supply for transmitter terminals 17, 21 Supply for receiver terminals 16, 17 Switching output terminals 19, 20 Stop in open + closed positions 2 (light barrier, potential-free contact) 24 V / 100 ma Supply for transmitter terminals 17, 24 Supply for receiver terminals 16, 17 Switching output terminals 22, Connection for potential-free contact e.g. bulb 230VAC / 2 A (at terminals 25, 26) Connection for lights Lights (bulb) (at terminals 29-34) Supply to lights (at terminals 27, 28) 230VAC / 2 A 230VAC / 2 A Connection for drive Drive close (relay) (at terminals 41, 42) Drive open (relay) (at terminals 40, 42) 230VAC / 4A 230VAC / 4A Device protection Type of protection IP Mechanical data Dimensions W x H x D Weight Installation position 160 mm x 250 mm x 127 mm 1800 g vertical Ambient conditions Temperature range 0-60 C Gate control operating manual mts2000/ meißner gate systems

24

25 Assembly and installation Safety information regarding assembly The control system may only be converted or modified once the agreement of the manufacturer has been sought. Always use genuine spare parts. Warranty cover ceases to apply if 3 rd party spare parts are used. When installing, starting up, maintaining and testing the control system, the always ensure compliance with applicable Health & Safety at Work regulations for the specific application must be noted. Amongst others, these rulings include: VDE 0100: Guidelines for setting up high power systems of up to 1000 V VDE 0105: Operating high-current electrical systems EN 60204: Electrical systems with electronic operating equipment VDE 0160: Equipping high power systems and electrical operating equipment VDE 0700: Safety of electrical devices for domestic consumption etc. BGV A2: BGR 232: Electrical systems and operating equipment Guidelines for power-assisted windows, doors and gates Gate control operating manual mts2000/ meißner gate systems

26 5 Assembly and installation 5.2 Fitting gate control mts2000/02 Select an assembly location for the gate control which ensures that the gate can be fully observed. Start-up and service work: For safety reasons, operators must be able to see the gate at all times while pressing the emergency stop switch. Prepare retaining bores for gate control housing (refer to Fig. 5-1 Housing dimensions of gate control). Screw on gate control cover and move cover to one side. Release retaining bolts of control board. Carefully and evenly withdraw board out of connection board. Move board to one side. Prevent static discharge on board! Only touch the edges of the board. Note ESD Directive. Drill holes depending on the quantity and size of lines in the housing. Insert PG screw connections in housing. Fit gate control housing to prepared point. Pull connection cable through PG screw connections and into housing. Attach cable to terminals according to Chapter 5.3, Electrical connection. Carefully attach control board to plug connections of connection board and use 3 screws to secure. Close and screw down cover. meißner gate systems 5-2 Gate control operating manual mts2000/02

27 Assembly and installation 5 Fig. 5-1 Housing dimensions of gate control Gate control operating manual mts2000/ meißner gate systems

28 5 Assembly and installation 5.3 Electrical connection The following diagram shows an overview of the connection board. Follow the references on the detailed diagrams. Connect the external inputs and outputs to gate control mts2000/02 as shown in these diagrams. Fig. 5-2 Connection boards of gate control mts2000/02 meißner gate systems 5-4 Gate control operating manual mts2000/02

29 Assembly and installation 5 Attach connections to connection board of gate control mts2000/02: 24 V connections 1) Gate control (controls) 2) Closing edge protection 3) Protection against anything being snagged or pulled in 230 V connections 1) 230 VAC connection 2) Lights, potential-free contact 3) Drive, mains supply Fig. 5-3 Impulse sensor Gate control operating manual mts2000/ meißner gate systems

30 5 Assembly and installation Fig. 5-4 Closing edge control meißner gate systems 5-6 Gate control operating manual mts2000/02

31 Assembly and installation 5 Fig. 5-5 Passage protection and protection against anything being snagged or pulled in, earthing 0 V Gate control operating manual mts2000/ meißner gate systems

32 5 Assembly and installation Fig. 5-6 Passage protection and protection against anything being snagged or pulled in, earthing 0 V meißner gate systems 5-8 Gate control operating manual mts2000/02

33 Assembly and installation 5 Fig. 5-7 Light connection and potential-free contact Gate control operating manual mts2000/ meißner gate systems

34 5 Assembly and installation Fig. 5-8 Emergency control and mains connection meißner gate systems 5-10 Gate control operating manual mts2000/02

35 Assembly and installation 5 Fig. 5-9 Drive Gate control operating manual mts2000/ meißner gate systems

36

37 Start-up and operation Programming gate control mts2000/02 To undertake programming, the gate control or gate system must be energised. Malfunctions cannot generally be ruled out at this time. Therefore cordon the gate system off from non-specialist staff. Ensure that you and your team have sufficient safety equipment. Energise the gate system: Switch on master switch and/or plug in connector Controls of gate control mts2000/02 Gate control mts2000/02 is programmed using 4 keys (refer to Fig. 4-1) on the control unit display board. The individual menu items of the control unit software are shown on the display. The keys are suppressed and have to be held down for around 1 second before they will respond Hardware settings (for more information, refer to Fig. 4-1) J1 Set according to the closing edge protection fitted J2 Apply jumper when system stop in open + closed position 1 is not connected up and/or no testing is needed (e.g. with reflection light barriers) J3 Apply jumper when system stop in open + closed position 2 is not connected up and/or no testing is needed (e.g. with reflection light barriers) For more information, also refer to Fig. 4-2 Gate control operating manual mts2000/ meißner gate systems

38 6 Start-up and operation Fig. 6-1 Removable display module with programming keys meißner gate systems 6-2 Gate control operating manual mts2000/02

39 Start-up and operation Function of keys Use key M to select a menu item. Use key P to select a parameter in the software for viewing and setting. Use the keys + and to increase or decrease by a specified step width the parameter selected. The value selected is entered by confirming the question Save? Menu structure of operating software Fig. 6-2 Menu levels of operating software for gate control mts2000/ Language setting The language is set on the display. For more information, refer to Chap Service, Language. Gate control operating manual mts2000/ meißner gate systems

40 6 Start-up and operation Program gate Here you will find information on the set values of the individual values for the Gate program menu item (refer to Fig. 6-2 Menu levels of operating software for gate control mts2000/02). Shown on LCD display Comments P R O G R A M G A T E P R E S S P P T O A B O R T P R E S S M T O C O N T I N U E P R E S S P P I N P U T S T A T U S ********* Stop in open + closed position 1 and 2 Stop Closing edge Stop in closed position Impulse open Impulse inside Impulse closed Impulse outside Continuously open externally or clock Impulse sequence open-stopclosed-stop Transmitter stop in open and closed position 1 functioning Transmitter stop in open and closed position 2 functioning * = Contact closed and/or functioning Assignment during operating mode for single or dual lanes Assignment during operating mode for impulse control P H A Z A R D F L A S H I N G / - 5 s Time between impulse emission and gate closing motion, red light flashes P meißner gate systems 6-4 Gate control operating manual mts2000/02

41 Start-up and operation 6 H O L D O P E N / s Time for which the gate remains open, not during impulse control P H O L D O P E N B R I E F / - o f f Only if light barrier is fitted for stop in closed position. Time after which the gate closes after passage, not during impulse control. P L I G H T A C T I V A T I O N F R O M O U T S I D E The potential-free contact closes during every impulse from inside or outside or inside+outside. Set impulse period using light period. If setting outside, impulse also during continuously open function. Only active if light activation is programmed in service. P R E - O P E N O P T I O N o n on: re-opens once closing edge has been activated off: revise once closing edge has been activated P L I G H T S D U R I N G C O N T O P E N O P T 0 Light times: Clearing phase = pre-warn time Green phase = hold open time P Only functions during one lane operating mode and continuously open, or clock mode. 0 = All lights off, green on request 1 = Autom. change, green inside and outside 2 = Green outside continuously, green inside on request 3 = Green inside continuously, green outside on request 4 = Red inside and outside, green on request R E D L I G H T G A T E C L O S E D O P T I O o f f on: red lights on when gate is closed. off: red lights off when gate is closed. P Gate control operating manual mts2000/ meißner gate systems

42 6 Start-up and operation H A Z A R D F L A S H I N G O P T I O N o n on: flashing when faults occur in operating process P R U N T I M E / s Time which the gate needs between limit positions when closing / opening. P C O N T I N U O U S L I G H T / - 1 s Impulse period of potential-free contact Only active if light activation is programmed in service. P S A V E? P H O L D D O W N Save settings --> hold down for 5 seconds, Reject changes --> press "M". P Press for 5 seconds S A V E? P S A V E D Save is acknowledged. P meißner gate systems 6-6 Gate control operating manual mts2000/02

43 Start-up and operation Service Here you will find information on the set values for the individual parameters of the Service menu item (refer to Fig. 6-2 Menu levels of the operating software for gate control mts2000/02). Use key M to select service menu Press and hold down + key, to do this press key P Shown on LCD display Comments S E R V I C E P S E R V I C E P R E S S M Only accessible to service fitters Hold down +, then press P + + P L A N G U A G E : G B + / - Use + / to select language P G A T E C Y C L E S 1 Counter for gate cycles, according to EN Chap (total cycle). P P R E S E T T I N G? Activate manufacturer presettings. Change: hold down + and, then press P P R E V E R S E T I M E / s Time after which the gate reopens when closing after closing edge or stop in closed position. P Gate control operating manual mts2000/ meißner gate systems

44 6 Start-up and operation O P E R A T I N G M O D E S I N G L E L A N E Operating modes available: Single lane with autom. closing. Dual lanes with autom. closing. Impulse control. P R E S E T O - T I M E V I A P P o n P on: hold open time reset when passage protection is activated. off: hold open time is not reset when passage protection is acti- vated (processed without interrupt) P O T. F R E E C O N T A C T L I G H T A C T I V A T I O N LIGHT ACTIVATION or FAULT MESSAGE can be selected. P S A V E? P H O L D D O W N Save settings --> hold down for 5 seconds, Reject changes --> press "M". P Press for 5 seconds S A V E? P S A V E D Save is acknowledged. P Operation Gate control mts2000/02 requires no operation. It is operated as part of the entire gate system using the controls connected to the system such as remote control, keys, continuously open switch. meißner gate systems 6-8 Gate control operating manual mts2000/02

45 Start-up and operation Assembly instructions for weekly time indexing clock mts2000/02 The clock (item 739) can be retrofitted Assembly 1. De-energise the system before assembly. 2. Attach clock to the intended connection point (refer to Fig. 4-1). 3. Re-energise system Programming In accordance with the programming instructions enclosed with the clock. Gate control operating manual mts2000/ meißner gate systems

46 6 Start-up and operation 6.3 Operating instructions for radio mts2000/02 The radio (item 91) can be retrofitted. The radio module is equipped with 2 channels, e.g. entrance and exit for one lane mode with automatic closing Assembly 1. De-energise the system before assembly. 2. Attach the radio plate to the intended connection point (refer to Fig. 4-1). The setting and display elements for the radio plate must face the inside of the housing. 3. The projectile antenna supplied should be in a vertical position. An external antenna (item 477) can be fitted if range problems are experienced. 4. Re-energise system Setting instructions 1. The setting on the 10-pin code switch must match that of the handheld transmitter. 2. The transmitter keys on the 4-pin code switch can be assigned channels, e.g. setting for one lane operations with automatic closing (entrance, exit). 1 = On 2 = Off 3 = On 4 = On meißner gate systems 6-10 Gate control operating manual mts2000/02

47 Start-up and operation Coding table Coding table Coding Left key Right key On Off On Off On Off On Off No function Channel 1 and 2 No function Channel 2 No function Channel 2 Channel 1 Channel 2 On Off On Off Channel 1 Channel 1 No function No function On Off On Off On Off No function Channel 1 No function Channel 1 Channel 2 Channel Displays Press left key, LED 1 lights up Press right key, LED 2 lights up Gate control operating manual mts2000/ meißner gate systems

48

49 Maintenance & service Troubleshooting tool The activities listed below may only be undertaken by specialists. Other people may cause damage to the device and injury to persons! Troubleshooting Troubleshooting is shown on the control system display Testing When an impulse is issued, testing of the stop in open + closed systems and closing edge protection is initiated. A system cannot be tested if ERROR TESTING appears on the control system display. The cause may e.g. be: - light barriers not aligned or not adjusted - light barrier receiver cannot be deactivated due to reflections - light barrier transmitter not connected to test output - light barrier receiver is affected by an external light (e.g. sun) - jumper J2 or J3 set - closing edge protection activated or defective - closing edge type incorrectly configured or not connected - consumers connected to terminals 21 or 24 when jumpers J2 and/or J3 are set Fault rectification Impact Gate not in end position Rectification Issue new command using keys or keyoperated switches etc. If nothing moves; call Service! Gate control operating manual mts2000/ meißner gate systems

50 7 Maintenance & service Control PCB measurement points Test specimen Measurement point 1 Mains connection Measurement points and values for control PCB, pins Measurement Measurement Measurement result Unit Condition Warning point 2 parameter Voltage +/- 230 VAC Mains voltage present 10% Emergency control, drive "CLOSED" Emergency control switch on PCB Resistance 0 Ohm CLOSED or external CLOSED emergency control switch pressed Emergency control switch on PCB Resistance infinite Ohm CLOSED or external CLOSED emergency control switch not pressed. No voltage at terminals 38 and 39 Emergency control, drive "OPEN" Emergency control switch on PCB Resistance 0 Ohm "OPEN" or external " OPEN" emergency control switch pressed Emergency control switch on PCB Resistance infinite Ohm " OPEN" or external " OPEN" emergency control switch not pressed. Outside green Resistance 0 Ohm Outside green light active 51 light 55 Resistance infinite Ohm Outside green light not active Outside red Resistance 0 Ohm Inside green light active 52 light 55 Resistance infinite Ohm Inside green light not active Inside green Resistance 0 Ohm Outside red light active 53 light 55 Resistance infinite Ohm Outside red light not active Resistance 0 Ohm Inside red light active Inside red light Resistance infinite Ohm Inside red light not active Resistance 0 Ohm Output active, contact closed Potential-free 58 contact 59 Resistance infinite Ohm Output inactive, contact opened No voltage at terminals 38 and 39 No voltage at terminals 27 and 28 No voltage at terminals 27 and 28 No voltage at terminals 27 and 28 No voltage at terminals 27 and 28 No voltage at terminals 25 and 26 Meißner gate systems 7-2 Gate control operating manual

51 Maintenance & service 7 Measurement points and values for control PCB, pins Test specimen Stop in open and closed positions 2 Stop in open and closed positions 2 Stop in open and closed positions 1 Control voltage Stop in closed position Auxiliary voltage for closing edge Closing edge as OSE Closing edge as EMC Continuously open and/or impulse sequence Measurem. Measurem. Measurem. point 1 point 2 parameter Voltage Measurem. result Unit Condition +/- 10% 24 VDC Transmitter for system 2 active Voltage 0 VDC Transmitter for system 2 inactive Voltage +/- 10% 24 VDC Voltage 0 VDC Transmitter for systems 1 and 2 active and receiver for systems 1 and 2 active (contacts closed) Transmitter for systems 1 or 2 inactive or receivers for systems 1 or 2 inactive (contacts open) Voltage +/- 10% 24 VDC Transmitter for system 1 active Voltage 0 VDC Transmitter for system 1 inactive Voltage +/- 10% 24 VDC Control system active Control system inactive or short Voltage 0 VDC circuit or ground/earth Voltage +/- 10% 24 VDC Voltage 0 VDC Voltage +/- 10% Voltage 0 VDC Voltage +/- 10% connection Transmitter for stop in closed position active and receiver active (contact closed) Transmitter for stop in closed position inactive or receiver inactive (contact open) 12 VDC Control system active 1,8 VDC Control system inactive or short circuit and/or ground/earth connection Closing edge active (not activated) Closing edge inactive (activated Voltage 0 VDC or conductor failure) Voltage Closing edge active (not 6 VDC +/- 10% activated) Voltage 10 VDC Closing edge activated Voltage 0 VDC Closing edge inactive, conductor failure Continuously open or impulse Voltage 24 VDC sequence activated (contact +/- 10% closed) Voltage 0 VDC Continuously open or impulse sequence not activated (contact open) Gate control operating manual mts2000/ meißner gate systems

52 7 7 Maintenance & service Measurement points and values for control PCB, pins Test specimen Impulse outside and/or closed impulse Impulse inside and/or open impulse Impulse for halt Measurem. Measurem. Measurem. Measurem. point 1 point 2 parameter result Voltage +/- 10% Unit 24 VDC Voltage 0 VDC Voltage +/- 10% 24 VDC Voltage 0 VDC Voltage +/- 10% 24 VDC Voltage 0 VDC Condition Impulse outside or closed impulse activated (contact closed) Impulse outside or closed impulse not activated (contact closed) Impulse inside or open impulse activated (contact closed) Impulse inside or open impulse not activated (contact closed) Impulse for halt and stop not activated (contact closed) Impulse for halt and stop activated (contact open) Meißner gate systems 7-4 Gate control operating manual mts2000/02

53 Maintenance & service Regular testing 1. Remove cover 2. Issue open impulse, gate runs into upper limit position 3. During single lane or dual lane operating mode, wait until the hold open and pre-warning time has expired. During impulse control operating mode, issue close command. 4. Status of LEDs during the test phase (also refer to Fig. 4-1). LED 1 LED 2 LED 3 LED 4 Before test Test stage Test stage Test stage Test stage After test Close housing again once test is complete. If result of testing is negative, shut down system and call service. Gate control operating manual mts2000/ meißner gate systems

54 7 7 Maintenance & service 7.3 Address of manufacturer Meißner GmbH Toranlagen Robert-Koch-Straße Kehl-Auenheim Germany Tel / Fax / info@meissner-gmbh.de Meißner gate systems 7-6 Gate control operating manual mts2000/02