FCC TEST REPORT. According to. FCC Rules and Regulations Part 15 Subpart C

Transcription

1 FCC TEST REPORT According to FCC Rules and Regulations Part 15 Subpart C Applicant : Billion Electric Co., Ltd. Address : 8F., No. 192, Sec. 2, Zhongxing Road, Xindian Dist., New Taipei City, Taiwan Equipment : Mobile Broadband Wireless-N Router Model No. : BiPAC 6200WZL R2, BiPAC 6200WZL R3, BiPAC 6200WZL R4, BiPAC 6200WZ R2, BiPAC 6200WZ R3, BiPAC 6200WZ R4, BEC 6200WZL R2, BEC 6200WZL R3, BEC 6200WZL R4, BEC 6200WZ R2, BEC 6200WZ R3, BEC 6200WZ R4 The test result refers exclusively to the test presented test model / sample., Without written approval of Cerpass Technology Corp., the test report shall not be reproduced except in full. The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Tel: Fax: Page No. : 1 of 88

2 Contents 1. Report of Measurements and Examinations List of Measurements and Examinations Test Configuration of Equipment under Test Feature of Equipment under Test Carrier Frequency of Channels Test Mode and Test Software Description of Test System General Information of Test Measurement Uncertainty Antenna Requirements Standard Applicable Antenna Construction and Directional Gain Test of Conducted Emission Test Limit Test Procedures Typical Test Setup Measurement Equipment Test Result and Data Test Photographs Test of Radiated Emission Test Limit Test Procedures Typical Test Setup Measurement Equipment Test Result and Data (9kHz ~ 30MHz) Test Result and Data Test Photographs (30MHz~1000MHz) Test Photographs (1000MHz~25000MHz) dB Bandwidth Measurement Data Test Limit Test Procedures Test Setup Layout Measurement Equipment Test Result and Data Maximum Peak and Average Output Power Test Limit Test Procedures Test Setup Layout Measurement Equipment Test Result and Data Power Spectral Density Test Limit Test Procedures Tel: Fax: Page No. : 2 of 88

3 8.3 Test Setup Layout Measurement Equipment Test Result and Data Band Edges Measurement Test Limit Test Procedure Test Setup Layout Measurement Equipment Test Result and Data Restrict Band Emission Measurement Data Restricted Bands of Operation Labeling Requirement Appendix A. Photographs of EUT.... A1 ~ A8 Tel: Fax: Page No. : 3 of 88

4 History of this test report ORIGINAL. Additional attachment as following record: Attachment No. Issue Date Description TEFI Oct. 02, 2012 Original. Tel: Fax: Page No. : 4 of 88

5 CERTIFICATE OF COMPLIANCE According to FCC Rules and Regulations Part 15 Subpart C Applicant : Billion Electric Co., Ltd. Address : 8F., No. 192, Sec. 2, Zhongxing Road, Xindian Dist., New Taipei City, Taiwan Equipment : Mobile Broadband Wireless-N Router Model No. : BiPAC 6200WZL R2, BiPAC 6200WZL R3, BiPAC 6200WZL R4, BiPAC 6200WZ R2, BiPAC 6200WZ R3, BiPAC 6200WZ R4, BEC 6200WZL R2, BEC 6200WZL R3, BEC 6200WZL R4, BEC 6200WZ R2, BEC 6200WZ R3, BEC 6200WZ R4 FCC ID : QI3BIL-6200WZLR3 I HEREBY CERTIFY THAT : The measurements shown in this test report were made in accordance with the procedures given in ANSI C , KDB & KDB The equipment was passed the test performed according to FCC Rules and Regulations Part 15 Subpart C (2010). The test was carried out on Sep. 25, 2012 at Cerpass Technology Corp. Approved by: Tested by: Hill Chen EMC/RF B.U. Assistant Manager Ben Lu Engineer Tel: Fax: Page No. : 5 of 88

6 1. Report of Measurements and Examinations 1.1 List of Measurements and Examinations FCC Rule. Description of Test Result Antenna Requirement Pass Conducted Emission Pass (d). Radiated Emission Pass (a)(2). 6dB Bandwidth Pass (b). Maximum Peak Output Power Pass (d). 100kHz Bandwidth of Frequency Band Edges Pass (e). Power Spectral Density Pass RF Exposure Compliance Pass Tel: Fax: Page No. : 6 of 88

7 2. Test Configuration of Equipment under Test 2.1 Feature of Equipment under Test Model difference is as follows, the other is for the same. Model name Brand EWAN Wireless-N Ethernet 10/100 USB port VPN IPSec BiPAC 6200WZL R2 Billion V V V V --- BiPAC 6200WZL R3 Billion V V V V --- BiPAC 6200WZL R4 Billion V V V BiPAC 6200WZ R2 Billion V V V V V BiPAC 6200WZ R3 Billion V V V V V BiPAC 6200WZ R4 Billion V V V --- V BEC 6200WZL R2 BEC V V V V --- BEC 6200WZL R3 BEC V V V V --- BEC 6200WZL R4 BEC V V V BEC 6200WZ R2 BEC V V V V V BEC 6200WZ R3 BEC V V V V V BEC 6200WZ R4 BEC V V V --- V 3G / 4G embedded with a built-in SIM card slot Dual WAN interfaces for EWAN and 3G / 3.5G / 3.75G / 4G connections 150Mbps. Wireless-N AP Supports Wi-Fi Protected Setup (WPS) and WPA-PSK / WPA2-PSK Supports multiple SSIDs for flexibility of network infrastructure High-speed wireless connection up to 150Mbps data rate Auto fail-over for always-on connection 3G / 4G Management Center for connection monitoring SOHO firewall security with DoS prevention and SPI Quality of Service control Syslog monitoring Ideal for SOHO users, Office users, and Event or meeting organizers Tel: Fax: Page No. : 7 of 88

8 Specifications: A. Electrical Characteristics Frequency 2400 ~ 2500 MHz S.W.R. <= 2.0 Antenna Gain 4.8 dbi Efficiency 48 ~ 50% Polarization Linear Impedance 50 Ohm B. Material & Mechanical Characteristics Material of Radiator PCB Cable Type O.D mm Connector Type Mini Connector Connector Pull Test >= 1 Kg C. Environmental Operation Temperature - 40 C ~ + 65 C Storage Temperature - 40 C ~ + 80 C Storage Time 1800 Days 2.2 Carrier Frequency of Channels b, g, n HT 20 Channel Frequency(MHz) Channel Frequency(MHz) n, HT40 Channel Frequency(MHz) Channel Frequency(MHz) Tel: Fax: Page No. : 8 of 88

9 2.3 Test Mode and Test Software a. During testing, the interface cables and equipment positions were varied according to ANSI C63.4. b. The complete test system included Notebook and EUT for the test. c. An executive program, QA TEST under WIN XP was executed to transmit and receive data to the remote workstation through WLAN. d. The following test modes were performed for test: b/g/n HT20: CH01: 2412MHz, CH06: 2437MHz, CH11: 2462MHz n HT40: CH03: 2422MHz, CH06: 2437MHz, CH09: 2452MHz *Adapter: EGB \ PAW018A12UL 8066 * Power output of data rate: b g n HT n HT40 Power Data Power Data Power Data Power Data Rate output Rate output Rate output Rate output (Mbps) (dbm) (Mbps) (dbm) (Mbps) (dbm) (Mbps) (dbm) / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Description of Test System Device Manufacturer Model No. Description Notebook ASUS A8J Power Cable, Unshielding 1.8m Use Cable: Cable Quantity Description RJ45 1 Unshielding, 1.0 m Tel: Fax: Page No. : 9 of 88

10 2.5 General Information of Test Test Site : Test Site Location (OATS2-SD) : Cerpass Technology Corp. 2F-11, No. 3, Yuan Qu St., (Nankang Software Park), Taipei, Taiwan 115, R.O.C. No.68-1, Shihbachongsi, Shihding Township, Taipei City 223, Taiwan, R.O.C. FCC Registration Number: TW1049, TW1061, , IC Registration Number : 4934B-1, 4934D-1 VCCI Registration Number: Frequency Range Investigated: Test Distance: T-1173 for Telecommunication Test C-4139 for Conducted emission test R-3428 for Radiated emission test G-97 for Radiated emission test above 1GHz Conducted: from 150kHz to 30MHz Radiation: from 30MHz to 25,000MHz The test distance of radiated emission from antenna to EUT is 3 M. Laboratory Accreditation 2.6 Measurement Uncertainty Measurement Item Radiated emission Peak Output Power(conducted) Peak Output Power(Radiated) Power Spectral Density Radiated emission(3m) Radiated emission(10m) Uncertainty 4.11dB 1.38dB 1.70dB 1.39dB 4.11dB 3.89dB Tel: Fax: Page No. : 10 of 88

11 3. Antenna Requirements 3.1 Standard Applicable For intentional device, according to FCC 47 CFR Section , an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in db that the directional gain of the antenna exceeds 6dBi. 3.2 Antenna Construction and Directional Gain Antenna Type: PCB Antenna Antenna Gain: 4.8 dbi Tel: Fax: Page No. : 11 of 88

12 4. Test of Conducted Emission 4.1 Test Limit Conducted Emissions were measured from 150 khz to 30 MHz with a bandwidth of 9 KHz on the 120 VAC power and return leads of the EUT according to the methods defined in ANSI C Section 3.1. The EUT was placed on a nonmetallic stand in a shielded room 0.8 meters above the ground plane as shown in section 2.2. The interface cables and equipment positioning were varied within limits of reasonable applications to determine the position produced maximum conducted emissions. Frequency (MHz) Quasi Peak (db µ V) Average (db µ V) * 56-46* *Decreases with the logarithm of the frequency. 4.2 Test Procedures a. The EUT was placed 0.4 meter from the conducting wall of the shielding room was kept at least 80 centimeters from any other grounded conducting surface. b. Connect EUT to the power mains through a line impedance stabilization network (LISN). c. All the support units are connecting to the other LISN. d. The LISN provides 50 ohm coupling impedance for the measuring instrument. e. The FCC states that a 50 ohm, 50 micro-henry LISN should be used. f. Both sides of AC line were checked for maximum conducted interference. g. The frequency range from 150 khz to 30 MHz was searched. h. Set the test-receiver system to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Tel: Fax: Page No. : 12 of 88 FCC ID : QI3BIL-6200WZLR3

13 4.3 Typical Test Setup 10cm Adapter EUT 80cm AC Line 80cm 80cm LISN 40cm LISN 40cm 4.4 Measurement Equipment Instrument/Ancillary Model No. Manufacturer Serial No. Calibration Date Valid Date EMI Receiver R&S ESCI /01/ /01/11 LISN Schwarzbeck NSLK /03/ /03/07 LISN Schwarzbeck NSLK /08/ /08/21 Tel: Fax: Page No. : 13 of 88

14 4.5 Test Result and Data Power : AC 120V Pol/Phase : LINE Test Mode 1 : g, CH1 Temperature : 23 C Test Date : Sep. 24, 2012 Humidity : 50 % Note: Level = Reading + Factor Margin = Level Limit Tel: Fax: Page No. : 14 of 88

15 Power : AC 120V Pol/Phase : NEUTRAL Test Mode 1 : g, CH1 Temperature : 23 C Test Date : Sep. 24, 2012 Humidity : 50 % Note: Level = Reading + Factor Margin = Level Limit Tel: Fax: Page No. : 15 of 88

16 Power : AC 120V Pol/Phase : LINE Test Mode 1 : n HT20, CH1 Temperature : 23 C Test Date : Sep. 24, 2012 Humidity : 50 % Note: Level = Reading + Factor Margin = Level Limit Tel: Fax: Page No. : 16 of 88

17 Power : AC 120V Pol/Phase : NEUTRAL Test Mode 1 : n HT20, CH1 Temperature : 23 C Test Date : Sep. 24, 2012 Humidity : 50 % Note: Level = Reading + Factor Margin = Level Limit Tel: Fax: Page No. : 17 of 88

18 Power : AC 120V Pol/Phase : LINE Test Mode 1 : n HT40, CH3 Temperature : 23 C Test Date : Sep. 24, 2012 Humidity : 50 % Note: Level = Reading + Factor Margin = Level Limit Tel: Fax: Page No. : 18 of 88

19 Power : AC 120V Pol/Phase : NEUTRAL Test Mode 1 : n HT40, CH3 Temperature : 23 C Test Date : Sep. 24, 2012 Humidity : 50 % Note: Level = Reading + Factor Margin = Level Limit Tel: Fax: Page No. : 19 of 88

20 5. Test of Radiated Emission 5.1 Test Limit In any 100kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. If the transmitter measurement is based on the maximum conducted output power, the attenuation required under this paragraph shall be 30dB instead of 20dB. In addition, radiated emissions which fall in section (a) the restricted bands must also comply with the radiated emission limit specified in section (a). Frequency (MHz) Field Strength (microvolt/meter) Measurement Distance (meters) ~ /F(kHz) ~ /F(kHz) ~ ~ ~ ~ Above Test Procedures a. The EUT was placed on a rotatable table top 0.8 meter above ground. b. The EUT was set 3 meters from the interference receiving antenna which was mounted on the top of a variable height antenna tower. c. The table was rotated 360 degrees to determine the position of the highest radiation. d. The antenna is a broadband antenna and its height is varied between one meter and four meters above ground to find the maximum value of the field strength both horizontal polarization and vertical polarization of the antenna are set to make the measurement. e. For each suspected emission the EUT was arranged to its worst case and then tune the antenna tower (from 1 M to 4 M) and turn table (from 0 degree to 360 degrees) to find the maximum reading. f. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function and specified bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 3 db lower than the limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 db margin will be repeated one by one using the quasi-peak method and reported. h. For testing above 1GHz, the emission level of the EUT in peak mode was 20dB lower than average limit (that means the emission level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. i. Cone of radiation has been considered to be 3dB bandwidth of the measurement antenna. Tel: Fax: Page No. : 21 of 88 FCC ID : QI3BIL-6200WZLR3

21 5.3 Typical Test Setup 5.4 Measurement Equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date EMI Receiver R&S ESCI /01/ /01/30 Amplifier QuieTek AP/0100A CHM /01/ /01/12 Signal Generator HP 8648B 3629U /01/ /01/10 Bilog Antenna Schwarzbeck VULB /03/ /03/22 Spectrum Analyzer R&S FSP /03/ /02/28 Horn Antenna EMCO /03/ /02/28 Preamplifier Agilent 8449B 3008A /02/ /02/28 Loop Antenna EMCO /02/ /02/28 Tel: Fax: Page No. : 22 of 88

22 5.5 Test Result and Data (9kHz ~ 30MHz) The 9kHz - 30MHz spurious emission is under limit 20dB more. 5.6 Test Result and Data Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : g, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 23 of 88

23 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : g, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 24 of 88

24 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : g, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 25 of 88

25 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : g, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 26 of 88

26 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : b, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 27 of 88

27 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : b, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 28 of 88

28 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : b, CH6 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 29 of 88

29 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : b, CH6 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 30 of 88

30 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : b, CH11 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 31 of 88

31 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : b, CH11 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 32 of 88

32 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : g, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 33 of 88

33 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : g, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 34 of 88

34 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : g, CH6 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 35 of 88

35 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : g, CH6 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 36 of 88

36 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : g, CH11 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 37 of 88

37 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : g, CH11 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 38 of 88

38 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT20, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 39 of 88

39 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT20, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 40 of 88

40 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT20, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 41 of 88

41 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT20, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 42 of 88

42 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT20, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 43 of 88

43 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT20, CH1 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 44 of 88

44 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT20, CH6 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 45 of 88

45 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT20, CH6 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 46 of 88

46 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT20, CH11 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 47 of 88

47 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT20, CH11 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 48 of 88

48 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT40, CH3 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 49 of 88

49 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT40, CH3 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 50 of 88

50 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT40, CH3 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 51 of 88

51 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT40, CH3 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 52 of 88

52 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT40, CH3 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 53 of 88

53 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT40, CH3 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 54 of 88

54 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT40, CH6 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 55 of 88

55 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT40, CH6 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 56 of 88

56 Power : AC 120V Pol/Phase : VERTICAL Test Mode 1 : n HT40, CH9 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 57 of 88

57 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode 1 : n HT40, CH9 Temperature : 25 C Adapter : EGB \ PAW018A12UL 8066 Humidity : 65 % Tel: Fax: Page No. : 58 of 88

58 6. 6dB Bandwidth Measurement Data 6.1 Test Limit The minimum of 6dB Bandwidth Measurement is 0.5 MHz. 6.2 Test Procedures a. The transmitter output was connected to the spectrum analyzer. b. Set RBW of spectrum analyzer to 1~5% of the emission bandwidth and VBW 3x RBW. c. The 6 db bandwidth is defined as the total spectrum the power of which is higher than peak power minus 6 db. d. The 6dB Bandwidth was measured and recorded. 6.3 Test Setup Layout 6.4 Measurement Equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date Spectrum Analyzer R&S FSP /11/ /11/ Test Result and Data Test Date: Sep. 24, 2012 Temperature: 25 Atmospheric pressure: 1020 hpa Humidity: 65% Modulation Standard Channel Frequency (MHz) 6dB Bandwidth (MHz) b (11Mbps) g (54Mbps) n HT20 (65Mbps) n HT40 (135Mbps) Tel: Fax: Page No. : 61 of 88

59 Modulation Standard: b (11Mbps) Channel: 01 Modulation Standard: b (11Mbps) Channel: 06 Tel: Fax: Page No. : 62 of 88

60 Modulation Standard: b (11Mbps) Channel: 11 Modulation Standard: g (54Mbps) Channel: 01 Tel: Fax: Page No. : 63 of 88

61 Modulation Standard: g (54Mbps) Channel: 06 Modulation Standard: g (54Mbps) Channel: 11 Tel: Fax: Page No. : 64 of 88

62 Modulation Standard: n HT20 (65Mbps) Channel: 01 Modulation Standard: n HT20 (65Mbps) Channel: 06 Tel: Fax: Page No. : 65 of 88

63 Modulation Standard: n HT20 (65Mbps) Channel: 11 Modulation Standard: n HT40 (135Mbps) Channel: 03 Tel: Fax: Page No. : 66 of 88

64 Modulation Standard: n HT40 (135Mbps) Channel: 06 Modulation Standard: n HT40 (135Mbps) Channel: 09 Tel: Fax: Page No. : 67 of 88

65 7. Maximum Peak and Average Output Power 7.1 Test Limit The Maximum Peak Output Power Measurement is 30dBm. 7.2 Test Procedures a. The transmitter output was connected to the Power meter. b. The maximum peak and average output power was measured and recorded. 7.3 Test Setup Layout 7.4 Measurement Equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date SERIES POWER METER Anritsu ML2495A /06/ /06/21 POWER SENSOR Anritsu MA2411B /07/ /07/08 Tel: Fax: Page No. : 68 of 88

66 7.5 Test Result and Data Test Date: Sep. 24, 2012 Temperature: 25 Atmospheric pressure: 1020 hpa Humidity: 65% Modulation Standard b (11Mbps) g (54Mbps) Channel Frequency (MHz) Peak Power Output (dbm) Power Output (mw) Peak Average Peak Average Modulation Standard n HT20 (65Mbps) n HT40 (135Mbps) Channel Frequency (MHz) Peak Power Output (dbm) Power Output (mw) Peak Average Peak Average Tel: Fax: Page No. : 69 of 88

67 8. Power Spectral Density 8.1 Test Limit The Maximum of Power Spectral Density Measurement is 8dBm. 8.2 Test Procedures a. The transmitter output was connected to spectrum analyzer. b. The spectrum analyzer s resolution bandwidth were set at 100KHz RBW and 300KHz VBW as that of the fundamental frequency. Set the sweep time=auto couple. c. Scale the observed power level to an equivalent value in 3 khz by adjusting the measured power by a bandwidth correction factor (BWCF) where BWCF= 10log (3 khz/100 = db). d. The power spectral density was measured and recorded. 8.3 Test Setup Layout 8.4 Measurement Equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date Spectrum Analyzer R&S FSP /11/ /11/ Test Result and Data Test Date: Sep. 24, 2012 Temperature: 25 Atmospheric pressure: 1020 hpa Humidity: 65% Modulation Standard b (11Mbps) g (54Mbps) Modulation Standard n HT20 (65Mbps) n HT40 (135Mbps) Channel Frequency (MHz) Measured Power Density (dbm) BWCF (db) Maximum Power Density of 3 khz Bandwidth (dbm) Channel Frequency (MHz) Measured Power Density (dbm) BWCF (db) Maximum Power Density of 3 khz Bandwidth (dbm) Tel: Fax: Page No. : 70 of 88

68 Modulation Standard: b (11Mbps) Channel: 01 Modulation Standard: b (11Mbps) Channel: 06 Tel: Fax: Page No. : 71 of 88

69 Modulation Standard: b (11Mbps) Channel: 11 Modulation Standard: g (54Mbps) Channel: 01 Tel: Fax: Page No. : 72 of 88

70 Modulation Standard: g (54Mbps) Channel: 06 Modulation Standard: g (54Mbps) Channel: 11 Tel: Fax: Page No. : 73 of 88

71 Modulation Standard: n HT20 (65Mbps) Channel: 01 Modulation Standard: n HT20 (65Mbps) Channel: 06 Tel: Fax: Page No. : 74 of 88

72 Modulation Standard: n HT20 (65Mbps) Channel: 11 Modulation Standard: n HT40 (135Mbps) Channel: 03 Tel: Fax: Page No. : 75 of 88

73 Modulation Standard: n HT40 (135Mbps) Channel: 06 Modulation Standard: n HT40 (135Mbps) Channel: 09 Tel: Fax: Page No. : 76 of 88

74 9. Band Edges Measurement 9.1 Test Limit Below 20dB of the highest emission level of operating band (In 100 khz Resolution Bandwidth) 9.2 Test Procedure a. The transmitter output was connected to the spectrum analyzer via a low lose cable. b. Set RBW of spectrum analyzer to 100 KHz and VBW of spectrum analyzer to 300 KHz with convenient frequency span including 100 KHz bandwidth from band edge. c. Peak conducted output power measured within any 100 khz outside the authorized frequency band shall be attenuated by at least 20dB relative to the maximum measured in-band peak PSD level. d. The band edges was measured and recorded. 9.3 Test Setup Layout 9.4 Measurement Equipment Instrument/Ancillary Manufacturer Model No. Serial No. Calibration Date Valid Date Spectrum Analyzer R&S FSP /11/ /11/ Test Result and Data Test Date: Sep. 24, 2012 Temperature: 25 Atmospheric pressure: 1020 hpa Humidity: 65% Modulation Standard b (11Mbps) g (54Mbps) n HT20 (65Mbps) n HT40 (135Mbps) Channel Frequency (MHz) maximum value in frequency (MHz) maximum value (dbm) Limit (dbm) Tel: Fax: Page No. : 77 of 88

75 Modulation Standard: b (11Mbps) Channel: 01 Tel: Fax: Page No. : 78 of 88

76 Modulation Standard: b (11Mbps) Channel: 11 Tel: Fax: Page No. : 79 of 88

77 Modulation Standard: g (54Mbps) Channel: 01 Tel: Fax: Page No. : 80 of 88

78 Modulation Standard: g (54Mbps) Channel: 11 Tel: Fax: Page No. : 81 of 88

79 Modulation Standard: n HT20 (65Mbps) Channel: 01 Tel: Fax: Page No. : 82 of 88

80 Modulation Standard: n HT20 (65Mbps) Channel: 11 Tel: Fax: Page No. : 83 of 88

81 Modulation Standard: n HT40 (135Mbps) Channel: 03 Tel: Fax: Page No. : 84 of 88

82 Modulation Standard: n HT40 (135Mbps) Channel: 09 Tel: Fax: Page No. : 85 of 88

83 9.6 Restrict Band Emission Measurement Data Test Date: Sep. 24, 2012 Temperature: 25 Atmospheric pressure: 1020 hpa Humidity: 65 % Adapter: EGB \ PAW018A12UL 8066 Modulation Standard: IEEE b (11Mbps) Channel 1 Frequency (MHz) Ant-Pol H/V Meter Reading (dbuv) Corrected Factor (db) Fundamental Frequency: 2412 MHz Result Limit (dbuv/m) Margin (dbuv/m) Remark Peak Ave (db) Table Deg. Ant High (m) H Peak H Ave V Peak V Ave Channel 11 Fundamental Frequency: 2462 MHz Frequency (MHz) Ant-Pol H/V Meter Reading (dbuv) Corrected Factor (db) Result Limit (dbuv/m) Margin (dbuv/m) Remark Peak Ave (db) Table Deg. Ant High (m) H Peak H Ave V Peak V Ave Modulation Standard: IEEE g (54Mbps) Channel 1 Frequency (MHz) Ant-Pol H/V Meter Reading (dbuv) Corrected Factor (db) Fundamental Frequency: 2412 MHz Result Limit (dbuv/m) Margin (dbuv/m) Remark Peak Ave (db) Table Deg. Ant High (m) H Peak H Ave V Peak V Ave Channel 11 Fundamental Frequency: 2462 MHz Frequency (MHz) Ant-Pol H/V Meter Reading (dbuv) Corrected Factor (db) Result Limit (dbuv/m) Margin (dbuv/m) Remark Peak Ave (db) Table Deg. Ant High (m) H Peak H Ave V Peak V Ave Tel: Fax: Page No. : 86 of 88

84 Modulation Standard: IEEE n HT20 (65Mbps) Channel 1 Frequency (MHz) Ant-Pol H/V Meter Reading (dbuv) Corrected Factor (db) Fundamental Frequency: 2412 MHz Result (dbuv/m) Remark Limit (dbuv/m) Margin (db) Peak Ave Table Deg. Ant High (m) H Peak H Ave V Peak V Ave Channel 11 Fundamental Frequency: 2462 MHz Frequency (MHz) Ant-Pol H/V Meter Reading (dbuv) Corrected Factor (db) Result Limit (dbuv/m) Margin (dbuv/m) Remark Peak Ave (db) Table Deg. Ant High (m) H Peak H Ave V Peak V Ave Modulation Standard: IEEE n HT40 (135Mbps) Channel 3 Frequency (MHz) Ant-Pol H/V Meter Reading (dbuv) Corrected Factor (db) Fundamental Frequency: 2422 MHz Result (dbuv/m) Remark Limit (dbuv/m) Margin (db) Peak Ave Table Deg. Ant High (m) H Peak H Ave V Peak V Ave Channel 9 Fundamental Frequency: 2452 MHz Frequency (MHz) Ant-Pol H/V Meter Reading (dbuv) Corrected Factor (db) Result Limit (dbuv/m) Margin (dbuv/m) Remark Peak Ave (db) Table Deg. Ant High (m) H Peak H Ave V Peak V Ave Notes: 1. Result = Meter Reading + Factor 2. Factor = Antenna Factor + Cable Loss Amplifier 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3 MHz (detector peak mode) for Peak detection at frequency above 1GHz. 4. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3 MHz (detector sample mode) for Average detection at frequency above 1GHz. Tel: Fax: Page No. : 87 of 88

85 10. Restricted Bands of Operation Only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz ** **: Until February 1, 1999, this restricted band shall be MHz 10.1 Labeling Requirement Above 38.6 The device shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Tel: Fax: Page No. : 88 of 88