DC San Ace Eco Products

Transcription

1 DC COOLING FAN 213

2 This DC fan series provides high quality and high reliability and features an extensive lineup of fans. Low Power Consumption Fan These fans greatly reduce power consumption while also providing large airflow and high static pressure. Power consumption is reduced up to a maximum of approximately 6% in comparison with our current fans. 4mm sq. to 92mm sq. 52mm sq. 15mm thick Model No.: 9GA512P7A1 Silent Fan Cooling fan that decrease noise and vibration 6mm sq. to 12mm sq. DC Fan Cooling fan operating at 5V, 12V, 24V, and 48V DC. An extensive lineup of fans featuring large airflow and high static pressure 36mm sq. to 2mm. Counter Rotating Fan Airflow and static pressure become higher than two conventional products of the same size connected in a series 38mm sq. to 172mm. Splash Proof Fan Cooling fan of IP54 and IP55 waterproof capability 6mm sq. to 172mm. Long Life Fan Cooling fan with Max. 2, hours of expected life 4mm sq. to 172mm. Centrifugal Fan Cooling fan blows air in a centrifugal course. It features high static pressure. 1mm to 175mm Blower Cooling fan specialized for high static pressure 52mm to 16mm Splash Proof Centrifugal Fan IP54 splash proof centrifugal fan 1mm to 175mm. CPU Cooler Models for cooling CPU Oil Proof Fan Cooling fan capable of operating in an oil-mist environment 4mm sq. to 12mm sq. 1

3 C O N T E N T S Domain Diagram P.3 to 5 Part Numbering System P.6 to 8 The meaning of the specifications Safety standards P.9 to 1 Low Power Consumption Fan 4mm sq. P.11 to 2 52mm sq. P.21 to 24 6mm sq. P.25 to 36 8mm sq. P.37 to 44 92mm sq. P.45 to 5 Silent Fan 6mm sq. P.51 to 52 8mm sq. P.53 to 54 92mm sq. P.55 to 56 12mm sq. P.57 to 58 DC Fan 36mm sq. P.59 to 6 38mm sq. P.61 to 62 4mm sq. P.63 to 78 52mm sq. P.79 to 8 6mm sq. P.81 to 98 8mm sq. P.99 to 12 92mm sq. P.121 to 13 12mm sq. P.131 to mm sq. P.149 to mm sq. P.153 to mm sq. P.155 to mm P.157 to 166 2mm P.167 to 17 Counter Rotating Fan 38mm sq. P.171 to 172 4mm sq. P.173 to 186 6mm sq. P.187 to 192 8mm sq. P.193 to mm sq. P.197 to mm P.199 to 2 Splash Proof Fan 6mm sq. P.21 to 22 8mm sq. P.23 to 28 92mm sq. P.29 to mm sq. P.215 to mm sq. P.223 to mm P.227 to 23 Splash Proof Centrifugal Fan 1mm P.231 to mm P.233 to mm P.235 to mm P.237 to 238 Oil Proof Fan 4mm sq. P.239 to 24 6mm sq. P.241 to 243 8mm sq. P mm sq. P.245 to mm sq. P.249 to 25 Long Life Fan 4mm sq. P.251 to 252 6mm sq. P.253 to 254 8mm sq. P.255 to mm sq. P.257 to mm sq. P.259 to mm sq. P.265 to mm P.269 to 272 Centrifugal Fan 1mm P.273 to mm P.275 to mm P.277 to mm P.279 to 28 Blower 52mm sq. P.281 to mm sq. P.283 to mm sq. P.287 to mm sq. P.292 to mm sq. P mm sq. P.296 CPU Cooler P.297 to 298 Fans with PWM speed control function P.299 Custom Product P.3 Option P.31 to 36 Technical Material Overview and characteristics of fan P.37 Guideline in selecting a fan P.37 Characteristics calculation method and description P.38 DC Fan Common Specifications P.39 Specifications for DC fan sensors P.39 to 31 PWM speed control function P.311 Splash Proof Fan P.312 Thermal speed controlled fans with an external or built-in thermistor P.313 to 314 Cautions for use of a cooling fan in the vicinity of a power switching circuit P.314 to 315 Operating precautions P.315 Fan mounting using self-tapping screw P.316 Safety Precautions P.317 to 318 Index by Model No./Safety Standards List P.319 to 324 Index by Frame Size/Safety Standards List P.325 to 331 Deleted models in this catalog P.333to 334 Network P.335 to 336 2

4 DC San Ace Domain Diagram Low Power Consumption Fan Air Flow(m 3 /min) Frame Size mm sq. 52mm sq. 6mm sq. 8mm sq. 92mm sq. Air Flow(CFM) Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.119 to to 12 P.121 P.21 to to P.121 P.25 to to P.119 P.37 to to P.121 P.45 to to Silent Fan Air Flow(m 3 /min) Frame Size mm sq. 8mm sq. 92mm sq. Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.51 to 52 P.53 to 54 P.55 to 56 12mm sq. Air Flow(CFM) P.57 to 58 DC Fan Air Flow(m 3 /min) Frame Size mm sq. 38mm sq. 4mm sq. Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.59 to 6 P.61 to 62 P.63 to 78 52mm sq. P.79 to 8 6mm sq. P.81 to 98 8mm sq. P.99 to 12 92mm sq. 12mm sq. 127mm sq. 14mm sq. P.121 to 13 P.131 to 148 P.149 to 152 P.153 to mm sq. 172mm 2mm Air Flow(CFM) P.155 to 156 P.157 to 166 P.167 to

5 Counter Rotating Fan Air Flow(m 3 /min) Frame Size mm sq. 4mm sq. 6mm sq. 8mm sq. Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.171 to 172 P.173 to 186 P.187 to 192 P.193 to mm sq. 172mm Air Flow(CFM) P.197 to 198 P.199 to 2 Splash Proof Fan Air Flow(m 3 /min) Frame Size mm sq. 8mm sq. 92mm sq. 12mm sq. 14mm sq. 172mm Air Flow(CFM) Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.21 to 22 P.23 to 28 P.29 to 214 P.215 to 222 P.223 to 226 P.227 to 23 Splash Proof Centrifugal Fan Air Flow(m 3 /min) Frame Size mm 133mm 15mm 175mm Air Flow(CFM) Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.231 to 232 P.233 to 234 P.235 to 236 P.237 to 238 Oil Proof Fan Air Flow(m 3 /min) Frame Size mm sq. 6mm sq. 8mm sq. 92mm sq. 12mm sq. Air Flow(CFM) Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.239 to 24 P.241 to 243 P.244 P.245 to 248 P.249 to 25 4

6 DC San Ace Domain Diagram Long Life Fan Air Flow(m 3 /min) Frame Size mm sq. 6mm sq. 8mm sq. 92mm sq. 12mm sq. 14mm sq. 172mm Air Flow(CFM) Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.251 to 252 P.253 to 254 P.255 to 256 P.257 to 258 P.259 to 264 P.265 to 268 P.269 to 272 Centrifugal Fan Air Flow(m 3 /min) Frame Size mm 133mm 15mm 175mm Air Flow(CFM) Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.273 to 274 P.275 to 276 P.277 to 278 P.279 to 28 Blower Air Flow(m 3 /min) Frame Size mm 76mm 97mm 12mm 127mm 16mm Air Flow(CFM) Conversion table 1m 3 /min=35.31(cfm) 1CFM=.283m 3 /min 1m 3 /min=16.67 /sec 1CFM=.472 /sec 1 /sec=.6m 3 /min Thick (mm) P.281 to 282 P.283 to 286 P.287 to 291 P.292 to 294 P.295 P.296 5

7 Part Numbering System Low Power Consumption Fan Not every combination of the following codes or characters is available. Contact us for an available combination. 9GA 6 12 H 6 1 There are no ribs for aluminum frame fans. Lock sensor can not be used in some models. Contact us for more information. Series name / frame material 9GA Plastics Frame size 4 4 4mm mm 6 6 6mm 8 8 8mm mm Voltage 12 12V 24 24V Speed code J,G,H,M,S etc Frame thickness 1 38mm thick 2 32mm thick 3 28mm thick 4 25mm thick 6 2mm thick 7 15mm thick Individual customer's spec 2 or 3 digits Frame form Nil Ribbed frame 1 Ribless frame Silent Fan 9S 6 12 H 4 1 Series name / frame material 9S Plastics Frame size 6 6 6mm 8 8 8mm mm mm Voltage 12 12V 24 24V Speed code F,H,L,M etc Frame thickness 4 25mm thick Sensor specifications 1 With a pulse sensor 2 Without a sensor D1 With a lock sensor Frame form Nil Ribbed frame 1 Ribless frame DC Fan 9GV J Series name / frame material 19P Plastics 19R Plastics 9GV Plastics Aluminum 9GE Aluminum 9G Plastics 9A Plastics 9SG Aluminum 19E Aluminum 9EC Aluminum Frame size mm mm 4 4 4mm mm 6 6 6mm 8 8 8mm mm mm mm mm mm mm Voltage 5 5V 12 12V 24 24V 48 48V etc mm 147mm(side cut) mm 15mm(side cut) 2 2mm Speed code A,B,C,D,E,F,G,H,J,K, L,M,S,W etc Two speed MH, LM,HD,HE etc Frame thickness 7mm 1 38mm thick 2 32mm thick 3 28mm thick 4 25mm thick 5 5mm thick 51mm thick 6 2mm thick 7 15mm thick 9 1mm thick Sensor specifications 1 With a pulse sensor 2 Without a sensor D1 With a lock sensor Frame form Nil Plastics frame: Ribbed frame Aluminum frame: Ribless frame 1 Plastics frame: Ribless frame mm for 1U applications Plastics frame Counter Rotating Fan 9CRA 4 12 K 4 1 Series name / frame material 9CR Plastics Aluminum 9CRA Plastics 9CRB Plastics 9CRE Aluminum 9CRD Plastics 9CRF Plastics Frame size Voltage mm 12 12V 4 4 4mm 48 48V 6 6 6mm 8 8 8mm mm mm 15mm(side cut) Speed code J,G,S,H,K etc Frame thickness 76mm thick 4 48mm thick 5 56mm thick 8 8mm thick 9 12mm thick Sensor specifications 1 With a pulse sensor 2 Without a sensor D1 With a lock sensor 6

8 DC San Ace Part Numbering System Splash Proof Fan Not every combination of the following codes or characters is available. Contact us for an available combination. 9WS H 1 1 Series name / frame material 19W Aluminum 9WS Plastics 9WE Aluminum 9WG Aluminum 9WB Aluminum 9WP Plastics9WP 9WV Plastics Frame size Voltage 6 6 6mm 12 12V 8 8 8mm 24 24V mm 48 48V mm etc mm mm mm 15mm(side cut) Speed code A,D,E,F,G,H,J,L, M,S etc Frame thickness 1 38mm thick 4 25mm thick 5 51mm thick Sensor specifications 1 With a pulse sensor 2 Without a sensor D1 With a lock sensor Frame form Nil Plastics frame: Ribbed frame Aluminum frame: Ribless frame 1 Plastics frame: Ribless frame Splash Proof Centrifugal Fan 9W1T M 48 P 4 H 1 Series name / frame material 9W1T Aluminum Size M 1mm J 133mm N 15mm G 175mm Voltage 24 24V 48 48V PWM speed control function P Frame thickness 69mm thick MIN 1 35mm thick 4 25mm thick Speed code H,G etc Individual customer's spec 2 or 3 digits Oil Proof Fan 9WF H 1 1 Series name / frame material 9WF Plastics Frame size 4 4 4mm 6 6 6mm 8 8 8mm mm mm Voltage 24 24V Speed code H Frame thickness 1 38mm thick 2 32mm thick 4 25mm thick 6 2mm thick 7 15mm thick Sensor specifications Frame form 1 With a pulse sensor Nil Ribbed frame 2 Without a sensor D1 With a lock sensor Long Life Fan 19L H 1 1 Series name / frame material 19L Aluminum 9LB Aluminum 9GL Aluminum 9 L Aluminum Frame size Voltage 4 4 4mm 12 12V 6 6 6mm 24 24V 8 8 8mm 48 48V mm etc mm mm mm mm 15mm(side cut) Speed code E,F,G,H,J,L,M,S etc Frame thickness 1 38mm thick 3 28mm thick 4 25mm thick 5 51mm thick Sensor specifications 1 With a pulse sensor 2 Without a sensor D1 With a lock sensor Centrifugal Fan 9T M 48 P 4 H Series name / frame material 9T Aluminum Size M 1mm J 133mm N 15mm G 175mm Voltage 24 24V 48 48V PWM speed control function P Frame thickness 69mm thick MIN 1 35mm thick 4 25mm thick Speed code H,G etc Individual customer's spec 2 or 3 digits 7

9 Blower 19B F 12 H C 2 There are no ribs for aluminum frame fans. Lock sensor can not be used in some models. Contact us for more information. Series name / frame material 19B Plastics 9B Plastics Frame size C 52mm D 76mm M 97mm F J G 12mm 127mm 16mm Voltage 12 12V 24 24V etc Speed code F,G,H,K,M,S etc Sensor specifications A Without a sensor C With a pulse sensor D With a lock sensor Frame thickness 1 4mm thick 2 3mm thick, 32mm thick, 33mm thick 7 15mm thick 6 2mm thick 9B MB 12 G 2 1 Series name / frame material 9B Plastics Frame size MB 97mm FB 12mm Voltage 12 12V 24 24V Speed code G S H etc Frame thickness 2 32mm thick 33mm thick Sensor specifications 1 With a pulse sensor 2 Without a sensor CPU Coolers with Speed Control 19X PT H 1 6 Series name / frame material 19X Plastics Product size 91 9mm 92 9mm Voltage 12 12V PT PWM control with thermal speed control Thickness code etc Speed code H Sensor specifications 1 With a pulse sensor 2 Without a sensor External view code 6 With a heat sink Fans with PWM speed control function Example : DC Fan Same patterns can be applied to the other fan types. Please contact us for further information. 9GV P 4 G 1 Series name / frame material 9GV Plastics Aluminum Frame size mm Voltage 12 12V PWM speed control function Frame thickness Speed code Individual customer's spec 2 or 3 digits Frame form Nil Ribbed frame *For inquiries concerning frame sizes, voltage, speed types, sensors (including lock sensors and low-speed sensors), speed control systems (including the two-speed system, the thermal speed control system, the PWM control function and the microprocessor control system) that are not covered in the catalog or on connectors, please contact us. 8

10 DC San Ace The meaning of the specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) C h 9G812G to , to 7 4, Rated Voltage This is the necessary voltage to drive the fan. DC12V, DC24V and DC48V are available. Single-phase AC1V, AC115V, AC2V and AC23V are also available. (Please refer to AC fan catalogue.) Operating Voltage Range The voltage range over which fan operation is guaranteed Rated Current The current value during the fan's rated operation without load Rated Input The input value during the fan's rated operation without load Rated Speed The rotating speed during the fan's rated operation without load Max. Air Flow The maximum air volume that the fan can output during rated operation (according to the company's dual-chamber device). The volume of air generated by the fan in a given time period Max. Static Pressure The maximum static pressure value that the fan can output during rated operation (according to the company's dual-chamber device). The static pressure is the fan's force to propel air by overcoming the resistance of the device that uses the fan when it propels air. SPL "SPL" is Sound Pressure Level. The noise level during the fan's rated operation. Please refer to Page 38 for the method used to measure the noise. Operating Temperature Range The temperature range over which fan operation is guaranteed (Non- condensing) Expected Life The fan's expected operating life when the fan operates continuously at the rated voltage at a temperature of 6 C and at relative humidity of 9%. For details, please refer to Page 38. Safety standards Description of safety standards 1. UL ratings (USA) List of safety standards acquired Please refer to Page 319 Underwriters Laboratories Inc. was established by the American Union of Fire Insurance Underwriters. The purpose of UL is to ensure safety of machines, equipment, and materials and protect human lives and property from fire and other accidents. To that end, UL has conducted numerous tests and extensive research and, as a result, set up UL ratings. Any seller of products in any of the majority of the states of the USA must produce their products according to the UL ratings, have them pass UL-specified safety inspections, and have them listed in UL's registration book. Therefore, to export and sell any product in the United States, one must in most cases apply for UL-listing. Additionally, UL is accredited by The Standards Council of Canada (SCC) as both a Certification Organization (CO) and a Testing Organization (TO) and is officially recognized in all provinces and territories throughout Canada. Accordingly, our products can be tested by UL for compliance with Canadian safety standards. Certified products are entitled to display the C-UL Mark, which authorizes their use and sale in Canada. If products are deemed to be compliant with both U.S. and Canadian standards, then both the UL Mark and C-UL Mark can be displayed or a combination U.S. and Canadian mark (bottom left). Our products are certified as satisfying all UL57 requirements. 2. CSA standards (Canada) The Canadian Standards Association (CSA) was set up in response to the advice of the Canadian government. In Canada, the law prohibits the use and sale of any product other than those approved under CSA in terms of safety. CSA has set up CSA standards as inspection procedures and other requirements to ensure product safety. Our products are certified as satisfying the CSA standard C22.2 No EN standards (EU members) In the EU territory, the harmonization of industrial standards and safety standards of different countries is under way. The unified standards are called Harmonized Standards. Each of these standards is marked EN above the standard number. EN standards offer the grounds in design and manufacture when one exports a product to the EU territory. In order for a product to receive a safety marking, the product must be found to conform to TÜV, VDE, or other relevant standard. Our products are certified as satisfying all TÜV Rheinland EN695 requirements. 4. E lec t r ical A pp l iance and Material Safety Law As of April 1, 21, the Electrical Appliance and Material Control Law has been revised and reenacted as the Electrical Appliance and Material Safety Law. AC fans are classified as Blowers under Electric motor-operated appliances. They are categorized as electrical products other than specific electrical appliances (with the exception of some models) and are required to be labeled to indicate PSE certification. 9

11 5. CE marking CE marking To distribute their equipment in the EU territory, manufacturers are obligated to give a CE marking as proof that the equipment conforms to related EU directives. Manufacturers use EN standards as criteria of judgment as to whether the equipment satisfies the requirements of specific directives or, in the absence of applicable EN standards, they use IEC standards. Manufacturers then prepare a self-declaration to indicate that the equipment conforms to related directives and apply a CE marking. (Depending on the degree of risk of the equipment, some kinds of equipment are required to receive type tests conducted by certified authorities and, after a type test certificate is obtained, manu-facturers make a self-declaration.) Scope of application and compulsory timing of major EC directives Machine directives (89/392/EEC, 91/368/EEC, and 93/44/EEC) These directives apply to equipment that has a moving part that may injure humans. The directives generally apply to a wide range of machine tools and other industrial machines (became compulsory on January 1, 1995). EMC directives (89/326/EEC and 92/31/EEC) They apply to equipment which may be affected by electromagnetic interference (EMI) or has ele-ctromagnetic susceptibility (EMS) (became co-mpulsory on January 1, 1996). Low-voltage directive (73/23/EEC) This directive applies to equipment that is used in an AC range between 5 and 1,V and in a DC range between 75 and 1,5V (became compulsory on January 1, 1997). JIS: Japanese Industrial Standards Japan's national standards related to mining and manufacturing industries IEC : International Electrotechnical Commission This is an international commission on electrical standardization. This commission promotes the unification and cooperation of international standards related to electric and electronics engineering and issues IEC standards in order eventually to allow different countries to conform to the international standards. DIN : Deutsches Indstitut fur Normung e.v. This is a German standards institute. The institute uses a wide-range set of standards covering many industrial sectors. The set of standards includes basic standards. VDE : Verband Deutscher Elektrotechniker e.v. It is a German association of electric engineers. VDE establishes safety standards related to electrical engineering and issues them as DIN-VDE standards. RoHS directive Since October 212, all the products in this catalog have complied with the maximum concentration values of the hazardous substances referred to in the Annex II to EU RoHS Directive 211/65/EU,* except for the exempted applications specified in the Annex III to the Directive. Please note that SANYO DENKI does not use exemption 7(c)-III: Lead in dielectric ceramic in capacitors for a rated voltage of less than 125 V AC or 25 V DC, for those products. * Lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE) RoHS Directive: DIRECTIVE 211/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June 211 on the restriction of the use of certain hazardous substances in electrical and electronic equipment 1

12 Low Power Consumption Fan 4mm sq. San Ace 4 15mm thick (GA type) 2mm thick (GA type) 28mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 28g GA type High air flow Specifications With PWM speed control function With pulse sensor Model No. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 9GA412P7G to , to 7 Note 1: Fan does not rotate when PWM duty cycle is %. Note 2: Expected life at 4 ambient is just reference value. Model No. With pulse sensor 4,/6 (7,/4 ) Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note1) V V A W min -1 m³/min Pa inchh ² O db(a) h 9GA412G , to GA412H , Note 1: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz 1 to 7 4,/6 (7,/4 ) Available upon request for all the models above. Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm (With PWM speed control function With pulse sensor) 4-3.5±.3 Mounting Hole ±.5 (4) (4) Reference dimension of mounting holes and vent opening Unit : mm (17.6) ±.3 32±.3 (1) 4 32±.3 4±.3 Lead Wire AWG28 UL17 (17.6) Rotating Direction Air Flow Direction 11

13 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver DC 12V 4 1 Air Flow - Static Pressure Characteristics 38.5 PWM Duty Cycle With PWM speed control function With pulse sensor Low Power Consumption Fan 4mm Static Pressure PWM Duty Cycle 1% 5% GA412P7G1 Operating Voltage Range.5 With PWM speed control function With pulse sensor Static Pressure PWM PWM 1 Duty Cycle V 12V 1.2V.5 Static Pressure V 12V 7V GA412P7G1 With pulse sensor 9GA412G71 DC12V.5 Static Pressure With pulse sensor 13.8V 12V 7V GA412H71 DC12V.25 PWM Duty - Speed Characteristics Example With PWM speed control function With pulse sensor Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 15, Rotation min Speed min , 5, 13,1min -1 1 PWM PWM % Duty Cycle % 9GA412P7G1 12 4mm

14 Low Power Consumption Fan 4mm sq. San Ace 4 15mm thick (GA type) 2mm thick (GA type) 28mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 4 4 2mm Mass 35g Specifications GA type High air flow Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h 9GA45P6H1 Note) , , to 5.5 9GA45P6F1 Note) , , , GA412P6G1 4, , , GA412P6H to , to 7 6, , GA412P6F , GA424P6G1 Note) , , 9GA424P6H1 Note) to , , 9GA424P6F1 Note) , Note: Rated voltage 5V and 24V fans do not rotate when PWM duty cycle is. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm Mounting Hole Reference dimension of mounting holes and vent opening Unit : mm (17.6) (1) Lead Wire AWG26 UL17 (4) 2.5 (4) 4 (17.6) Rotating Direction Air Flow Direction 13

15 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Air Flow - Static Pressure Characteristics 38.5 Low Power Consumption Fan 4mm PWM Duty Cycle DC 5V 12 DC 5V Static Pressure PWM Duty Cycle 1% 5% Static Pressure PWM Duty Cycle 1% 5% GA45P6H Air Flow 9GA45P6F1.3 1 Operating Voltage Range PWM PWM 1 Duty Cycle 1 12 PWM PWM 1 Duty Cycle 1 Static Pressure V 5V 4.5V Static Pressure V 5V 4.5V GA45P6H GA45P6F1 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 5V DC5V DC PWM 25kHz Frequency 25kHz 14, 9GA45P6H1 12, 12,4min -1 1, 8, 6, 4, 2, 9GA45P6F1 8,min -1 1 PWM PWM % Duty Cycle % 9GA45P6H1 9GA45P6F1 14 4mm

16 Low Power Consumption Fan 4mm sq. San Ace mm Mass 35g Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure DC 12V PWM Duty Cycle 1% 5% % Air Flow 9GA412P6G1 Operating Voltage Range Static Pressure PWM Duty Cycle 15 1% 1 5 5% % DC 12V GA412P6H1 Static Pressure % PWM Duty Cycle 1%.1 5% Air Flow DC 12V 9GA412P6F1.3 1 Static Pressure PWM PWM 1 Duty Cycle V V V GA412P6G1 Static Pressure PWM PWM 1 Duty Cycle V V V GA412P6H1 Static Pressure 12 PWM PWM 1 Duty Cycle V V V GA412P6F1 PWM Duty - Speed Characteristics Example Rotation min Speed min , 14, 12, 1, 8, 6, 4, 2, Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 3,8min -1 2,2min -1 9GA412P6G1 16,min -1 9GA412P6H1 12,4min -1 9GA412P6F1 8,min -1 Rotation min Speed min , 14, 12, 1, 8, 6, 4, 2, Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz 9GA424P6G1 16,min -1 9GA424P6H1 12,4min -1 9GA424P6F1 8,min -1 1 PWM PWM % Duty Cycle % 9GA412P6G1 9GA412P6H1 9GA412P6F1 1 PWM PWM % Duty Cycle % 9GA424P6G1 9GA424P6H1 9GA424P6F1 15

17 Static Pressure PWM Duty Cycle 1% %.1.2 Static Pressure PWM PWM 1 Duty Cycle V V V Air Flow 9GA424P6G1 Static Pressure PWM PWM 1 Duty Cycle V V V Air Flow 9GA424P6H1 Static Pressure 12 PWM PWM 1 Duty Cycle V V V Air Flow 9GA424P6F1.3 4mm DC 24V GA424P6G1 Static Pressure PWM Duty Cycle 1%.2 5 5%.1 DC 24V GA424P6H1 Static Pressure PWM Duty Cycle 1% %.1.2 DC 24V GA424P6F1 Low Power Consumption Fan 4mm 16

18 Low Power Consumption Fan 4mm sq. San Ace 4 15mm thick (GA type) 2mm thick (GA type) 28mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 53g GA type Specifications To order a ribless type, replace the last digits of a model number with digits in parenthesis. Model No. 9GA412P3K1(11) 9GA412P3J1(11) 9GA412P3G1(11) 9GA412P3H1(11) 9GA412P3M1(11) Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , , to 6 3, , , , to , to 7 4, , , , , Available upon request for all the models above. PWM Frequency 25kHz Dimensions Unit : mm (With ribs) Mounting Hole Lead Wire AWG26 UL Rotating Direction Air Flow Direction 17

19 Reference dimension of mounting holes and vent opening Unit : mm Low Power Consumption Fan 4mm Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver mm

20 Low Power Consumption Fan 4mm sq. San Ace mm Mass 53g Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure DC 12V 1, PWM Duty Cycle 5 1% % GA412P3K1(11) % PWM Duty Cycle 1% 5% DC 12V GA412P3J1(11) % PWM Duty Cycle 1% 5% DC 12V GA412P3G1(11) Operating Voltage Range Static Pressure 4. 1, PWM PWM 1 Duty Cycle V V V GA412P3K1(11) PWM PWM 1 Duty Cycle V 12V 1.8V GA412P3J1(11) PWM PWM 1 Duty Cycle V 12V 1.8V GA412P3G1(11) PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 2, 15, 1, 6,5min -1 5, 22,min -1 min Rotation Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 1, 5, 4,5min -1 18,min -1 min Rotation Speed min , 15, 1, 5, Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 4,5min -1 16,5min -1 1 PWM PWM % Duty Cycle % 9GA412P3K1(11) 1 PWM PWM % Duty Cycle % 9GA412P3J1(11) 1 PWM PWM % Duty Cycle % 9GA412P3G1(11) 19

21 DC 12V PWM Duty Cycle 1%.5 1 5% % GA412P3H1(11) Static Pressure DC 12V PWM Duty Cycle 1% % % GA412P3M1(11) Low Power Consumption Fan 4mm PWM PWM 1 Duty Cycle V 12V 1.8V GA412P3H1(11) min Rotation Speed min , 15, 1, 5, Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 3,5min -1 14,5min -1 1 PWM PWM % Duty Cycle % 9GA412P3H1(11) 4mm PWM PWM 1 Duty Cycle V 12V 1.8V GA412P3M1(11) min Rotation Speed min , 15, 1, 5, Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 3,5min -1 12,5min -1 1 PWM PWM % Duty Cycle % 9GA412P3M1(11) 2

22 Low Power Consumption Fan 52mm sq. San Ace 52 15mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 4g Specifications GA type Model No. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle Note) % A W min -1 m³/min Pa inchh ² O db(a) h 9GA512P7G , GA512P7A , to GA512P7H , GA524P7A , to GA524P7H , GA512P7M , GA524P7G , to 7 4, 9GA524P7M , Note : Fan does not rotate when PWM duty cycle is %. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm Mounting Hole Rotating Direction (1) Lead Wire AWG26 UL17 (3) (3) 15.5 Air Flow Direction 21

23 Reference dimension of mounting holes and vent opening Unit : mm Low Power Consumption Fan 52mm Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model E Surface treatment Nickel-chrome plating silver Outlet side mm

24 Low Power Consumption Fan 52mm sq. San Ace mm Mass 4g Air Flow - Static Pressure Characteristics PWM Duty Cycle DC12V/24V PWM Duty Cycle 1% 5% DC12V/24V PWM Duty Cycle 1% 5% DC12V/24V PWM Duty Cycle 1% 5% Air Flow 9GA512P7G1 9GA524P7G1 Operating Voltage Range 9GA512P7A1 9GA524P7A GA512P7H1 9GA524P7H PWM PWM 1 Duty Cycle V/27.6V 12V/24V 1.2V/2.4V PWM PWM 1 Duty Cycle V/27.6V 12V/24V 1.2V/2.4V PWM PWM 1 Duty Cycle V/27.6V 12V/24V 1.2V/2.4V GA512P7G1 9GA524P7G1 9GA512P7A1 9GA524P7A GA512P7H1 9GA524P7H1 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V/24V / 24V DC 8, PWM 25kHz Frequency 25kHz 7,8min -1 6, 4, 2, 1 PWM PWM % Duty Cycle % 9GA512P7G1 9GA524P7G1 Rotation min Speed min -1-1 Voltage 12V DC12V // 24V DC PWM 25kHz Frequency 25kHz 8, 6,3min 6, -1 4, 2, 1 PWM PWM % Duty Cycle % 9GA512P7A1 9GA524P7A1 Rotation min Speed min -1-1 Voltage 12V DC12V // 24V DC PWM 25kHz Frequency 25kHz 6, 5, 4, 3, 2, 1, 4,3min -1 1 PWM PWM % Duty Cycle % 9GA512P7H1 9GA524P7H1 23

25 DC12V/24V PWM Duty Cycle 1% 5% Low Power Consumption Fan 52mm GA512P7M1 9GA524P7M PWM PWM 1 Duty Cycle V/27.6V 12V/24V 1.2V/2.4V GA512P7M1 9GA524P7M1 Rotation min Speed min -1-1 Voltage 12V DC12V // 24V DC PWM 25kHz Frequency 25kHz 6, 5, 4, 3,4min -1 3, 2, 1, 1 PWM PWM % Duty Cycle % 9GA512P7M1 9GA524P7M1 52mm 24

26 Low Power Consumption Fan 6mm sq. San Ace 6 15mm thick (GA type) 2mm thick (GA type) 38mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 5g GA type Specifications With PWM speed control function With pulse sensor Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note) Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , GA612P7G , ,/ to to , (7,/4 ) 9GA612P7H , Note: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Model No. With pulse sensor Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9GA612M , to GA612L , to 7 6, Available upon request for all the models above. Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm (With PWM speed control function With pulse sensor) Mounting Hole (3) 15.5 (3) Lead Wire AWG28 UL (1) Air Flow Direction Rotating Direction 25

27 Reference dimension of mounting holes and vent opening Unit : mm Low Power Consumption Fan 6mm Options Unit : mm Finger guards Model E H 53 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G mm Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI

28 Low Power Consumption Fan 6mm sq. San Ace mm Mass 5g Air Flow - Static Pressure Characteristics PWM Duty Cycle With PWM speed control function With pulse sensor Static Pressure % DC 12V PWM Duty Cycle 1% 5% Air Flow 9GA612P7G1 3 With PWM speed control function With pulse sensor Static Pressure % 5% DC 12V PWM Duty Cycle 1% Air Flow 9GA612P7H1 Operating Voltage Range With PWM speed control function With pulse sensor With PWM speed control function With pulse sensor With pulse sensor PWM Duty Cycle 1.45 PWM 1 PWM V V V V 12V V V 3 1.2V V m /min PWM Duty Cycle 1 9GA612P7G1 9GA612P7H1 9GA612M71 Static Pressure PWM Duty - Speed Characteristics Example With PWM speed control function With pulse sensor min Rotation Speed min , Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 5,9min -1 5, 4, 3, 2, 1,5min -1 1, With PWM speed control function With pulse sensor min Rotation Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 5, 4,9min -1 4, 3, 2, 1,3min -1 1, 1 PWM PWM % Duty Cycle % 9GA612P7G1 1 PWM PWM % Duty Cycle % 9GA612P7H1 27

29 .12 3 Static Pressure GA612L71 6mm Low Power Consumption Fan 6mm With pulse sensor 6V 13.8V 12V 28

30 Low Power Consumption Fan 6mm sq. San Ace 6 15mm thick (GA type) 2mm thick (GA type) 38mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 6 6 2mm Mass 7g Specifications With PWM speed control function With pulse sensor With pulse sensor GA type Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 9GA612P6G , to GA612P6S , to 7 4,/6 9GA624P6G , (7,/4 ) to GA624P6S , Note 1: Fan does not rotate when PWM duty cycle is %. Note 2: Expected life at 4 ambient is just reference value. Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9GA612H , to GA612M , GA624H , to GA624M , PWM Frequency 25kHz 1 to 7 6, Available upon request for all the models above. Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm (With PWM speed control function With pulse sensor) Mounting Hole Lead Wire AWG26 UL (1) Rotating Direction (4) (4) 2.5 Air Flow Direction 29

31 Reference dimension of mounting holes and vent opening Unit : mm Low Power Consumption Fan 6mm Options Unit : mm Finger guards Model E H 53 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G mm Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI

32 Low Power Consumption Fan 6mm sq. San Ace mm Mass 7g Air Flow - Static Pressure Characteristics PWM Duty Cycle With PWM speed control function With pulse sensor DC12V PWM Duty Cycle 1% 5% Air Flow 9GA612P6G1 With PWM speed control function With pulse sensor DC12V PWM Duty Cycle 1% 5% Air Flow 9GA612P6S1 With PWM speed control function With pulse sensor %.2.4 DC24V PWM Duty Cycle 1% Air Flow 9GA624P6G1 Operating Voltage Range With PWM speed control function With pulse sensor PWM PWM 1 Duty Cycle V 12V 1.8V Air Flow 9GA612P6G1 With PWM speed control function With pulse sensor PWM PWM 1 Duty Cycle V 12V 1.8V GA612P6S1.8 With PWM speed control function With pulse sensor PWM PWM 1 Duty Cycle V 24V 21.6V Air Flow 9GA624P6G1 PWM Duty - Speed Characteristics Example With PWM speed control function With pulse sensor With PWM speed control function With pulse sensor With PWM speed control function With pulse sensor Voltage 12V DC12V DC Voltage 12V DC12V DC Voltage 24V DC24V DC PWM 25kHz Frequency 25kHz PWM 25kHz Frequency 25kHz PWM PWM 25kHz Frequency 25kHz 8, 6, 8, 7, 6,85min -1 5,5min -1 7, 5, 6, 6, 6,85min -1 5, 4, 5, 4, 3, 4, 3, 2, 2, 3, 2, 1, 1, 1, PWM PWM % Duty Cycle % PWM PWM % Duty Cycle % PWM PWM % Duty Cycle % Rotation min Speed min -1-1 Rotation min Speed min GA612P6G1 9GA612P6S1 9GA624P6G1 Rotation min Speed min

33 With PWM speed control function With pulse sensor.4 1 DC24V Low Power Consumption Fan 6mm PWM Duty Cycle 1% 5% Air Flow 9GA624P6S1 With PWM speed control function With pulse sensor.4 1 PWM PWM 1 Duty Cycle 1 6 With pulse sensor DC12V/DC24V.12 3 With pulse sensor DC12V/DC24V V 24V 21.6V V / 26.4V 12V / 24V 1.8V / 21.6V V / 26.4V 12V / 24V 1.8V / 21.6V GA624P6S Air Flow 9GA612H61 9GA624H GA612M61 9GA624M61 With PWM speed control function With pulse sensor Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz 6, 5,5min -1 5, 4, 3, 2, 1, 1 PWM PWM % Duty Cycle % 9GA624P6S1 6mm 32

34 Low Power Consumption Fan 6mm sq. San Ace 6 15mm thick (GA type) 2mm thick (GA type) 38mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 13g GA type Specifications To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h , GA612P1J3(31) 1.8 to to 6 4, , , GA612P1K3(31) , to , ,/6 9GA612P1H3(31) 1.8 to , (7,/4 ) , GA612P1K6(61).5.6 1, to , GA624P1J3(31) to , , Note 1: 9GA612P1J3(31) 9GA612P1K3(31) 9GA612P1H3(31) does not rotate when PWM duty cycle is %. Note 2: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm (With ribs) Mounting Hole +5 3 (1) Lead Wire AWG24 UL (4) 38.5 (4) Rotating Direction Air Flow Direction 33

35 Reference dimension of mounting holes and vent opening Unit : mm Low Power Consumption Fan 6mm Options Unit : mm Finger guards Model E H 53 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G mm Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI

36 Low Power Consumption Fan 6mm sq. San Ace mm Mass 13g Air Flow - Static Pressure Characteristics PWM Duty Cycle 3. 8 PWM Duty Cycle 7 1% % 6% DC 12V Air Flow Air Flow 9GA612P1J3(31) Operating Voltage Range PWM Duty Cycle 1% 2% 6% DC 12V 9GA612P1K3(31) PWM Duty Cycle 1% 2% 6% DC 12V 9GA612P1H3(31) PWM PWM 1 Duty Cycle V 12V 1.8V PWM PWM 1 Duty Cycle V 12V GA612P1J3(31) 1.8V 9GA612P1K3(31) Static Pressure PWM Duty Cycle 1 PWM V 12V 1.8V 9GA612P1H3(31) PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 18, 17,5min -1 16, 14, 12, 1, 8, 6, 4, 2, 1 PWM PWM % Duty Cycle % 9GA612P1J3(31) Rotation min Speed min , 14, 12, 1, Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 14,8min -1 8, 6, 4, 2, 1 PWM PWM % Duty Cycle % 9GA612P1K3(31) Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 14, 12, 1, 8, 6, 4, 2, 11,5min -1 1 PWM PWM % Duty Cycle % 9GA612P1H3(31) 35

37 7 2.5 PWM Duty Cycle 6 1% % % DC 12V Air Flow 9GA612P1K6(61) Static Pressure PWM Duty Cycle 1% 2% 6% DC 24V GA624P1J3 31 Low Power Consumption Fan 6mm PWM Duty Cycle 1 PWM V,12V 1.8V Air Flow 9GA612P1K6(61) Static Pressure PWM PWM 1 Duty Cycle V V V GA624P1J3 31 Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 16, 14,8min -1 14, 12, 1, 8, 6, 4, 2, 1,48min -1 1 PWM PWM % Duty Cycle % 9GA612P1K6(61) Rotation min Speed min -1-1 Voltage 12V DC24V DC PWM PWM 25kHz Frequency 25kHz 18, 17,5min -1 16, 14, 12, 1, 8, 6, 4, 2, 1 PWM PWM % Duty Cycle % 9GA624P1J3 31 6mm 36

38 Low Power Consumption Fan 8mm sq. San Ace 8 2mm thick (GA type) 32mm thick (GA type) 38mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 8 8 2mm Mass 8g Specifications GA type Model No. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 4,/6 9GA812P6G , to (7,/4 ) 9GA812P6M , ,/6 1 to 7 4,/6 9GA824P6G , to (7,/4 ) 9GA824P6M , ,/6 Note 1: Does not rotate when PWM duty cycle is %. Note 2: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm Mounting Hole (4) 2.5 (4) Reference dimension of mounting holes and vent opening Unit : mm (1) Rotating Direction Lead Wire AWG26 UL17 Air Flow Direction 78.5 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black

39 Options Unit : mm Resin finger guards Model 19-12G Static Pressure PWM Duty Cycle 1%.8 5% DC 12V/24V Air Flow - Static Pressure Characteristics PWM Duty Cycle 9GA812P6G1 9GA824P6G1 Operating Voltage Range Static Pressure PWM Duty Cycle 1% 5% DC 12V/24V GA812P6M1 9GA824P6M1 Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Low Power Consumption Fan 8mm Static Pressure 14 PWM PWM 1 Duty Cycle V/27.6V V/24V 1.2V/2.4V Air Flow 9GA812P6G1 9GA824P6G1 Static Pressure PWM PWM 1 Duty Cycle V/27.6V 12V/24V 1.2V/2.4V GA812P6M1 9GA824P6M1 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC / DC24V / 24V DC PWM 25kHz Frequency 25kHz 7,5 5, 2,5 5,85min -1 1 PWM PWM % Duty Cycle % 9GA812P6G1 9GA824P6G1 Rotation min Speed min -1-1 Voltage 12V DC12V / DC DC24V / 24V DC PWM PWM 25kHz Frequency 25kHz 3, 2,9min -1 2, 1, 1 PWM PWM % Duty Cycle % 9GA812P6M1 9GA824P6M1 38 8mm

40 Low Power Consumption Fan 8mm sq. San Ace 8 2mm thick (GA type) 32mm thick (GA type) 38mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 13g GA type Specifications High air flow To order a ribless type, replace the last digits of a model number with digits in parenthesis. Model No. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , GA812P2S1(11) , to to , GA812P2H1(11) , , , GA812P2M1(11) 1.2 to , GA824P2S1(11) to , , to 7 PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm (With ribs) Ø4.5.3 Mounting Hole Lead Wire AWG26 UL (1) Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction (4) (4) 32.5 Air Flow Direction 78.5 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black

41 Options Unit : mm Resin finger guards Model 19-12G Static Pressure DC 12V/24V Air Flow - Static Pressure Characteristics PWM Duty Cycle PWM Duty Cycle 1.4 PWM Duty Cycle 1% PWM Duty Cycle 1% % % 5% 5% % %.2 % Air Flow 9GA812P2S1(11) 9GA824P2S1(11) Static Pressure DC 12V 9GA812P2H1(11) Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Static Pressure 9GA812P2M1(11) Low Power Consumption Fan 8mm Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle 1 Static Pressure PWM PWM 1 Duty Cycle V/27.6V V V 12V/24V 1. 12V V.6 1.2V V/2.4V m /min Air Flow Air Flow 9GA812P2S1(11) 9GA824P2S1(11) 13.8V 9GA812P2H1(11) Static Pressure 9GA812P2M1(11) PWM Duty - Speed Characteristics Example Rotation min Speed min , 9, 8, 7, 6, 5, 4, 3, 2, Voltage 12V DC12V / DC 24V/ 24V DC PWM 25kHz Frequency 25kHz 9,7min -1 2,8min -1 1, 1 PWM PWM % Duty Cycle % 9GA812P2S1(11) 9GA824P2S1(11) Rotation min Speed min , 9, 8, 7, 6, 5, 4, 3, 2, Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 8,7min -1 2,6min -1 1, 1 PWM PWM % Duty Cycle % 9GA812P2H1(11) Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 1, 9, 8, 7, 6, 5, 4, 6,7min -1 3, 2, 1,4min 1, -1 1 PWM PWM % Duty Cycle % 9GA812P2M1(11) 4 8mm

42 Low Power Consumption Fan 8mm sq. San Ace 8 2mm thick (GA type) 32mm thick (GA type) 38mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 16g GA type Specifications To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note) Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , GA812P1S61(611) , to , GA812P1H61(611) , ,/6 1 to , (7,/4 ) 9GA824P1S61(611) , to , GA824P1H61(611) , Note: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm (With ribs) Mounting Hole (1) Lead Wire AWG26 UL143 (4) (4) 38.5 Rotating Direction Air Flow Direction 41

43 Reference dimension of mounting holes and vent opening Unit : mm Low Power Consumption Fan 8mm Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side Model 19-49E 19-49H 11.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI mm

44 Low Power Consumption Fan 8mm sq. San Ace mm Mass 16g Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V PWM Duty Cycle 1% 9GA812P1S61(611) DC 12V PWM Duty Cycle 1% 5% 5% % % %.4 1 % m /min GA812P1H61(611) DC 24V PWM Duty Cycle 1% 9GA824P1S61(611) Operating Voltage Range PWM PWM 1 Duty Cycle V 12V 1.8V PWM PWM 1 Duty Cycle V 12V 1.8V 9GA812P1H61(611) Static Pressure PWM Duty Cycle 1 PWM m /min m /min Air Flow Air Flow 9GA812P1S61(611) V 24V 2.4V 1 9GA824P1S61(611) 3 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC / DC24V / 24V DC PWM PWM 25kHz Frequency 25kHz 1, 8, 6, 4, 2,9min -1 2, 9,55min -1 Rotation min Speed min -1-1 Voltage 12V DC12V DC / DC24V / 24V DC PWM PWM 25kHz Frequency 25kHz 1, 8, 6, 4, 2, 2,5min -1 8,25min -1 1 PWM PWM % Duty Cycle % 9GA812P1S61(611) 9GA824P1S61(611) 1 PWM PWM % Duty Cycle % 9GA812P1H61(611) 9GA824P1H61(611) 43

45 % DC 24V PWM Duty Cycle 1% 5% GA824P1H61(611) Static Pressure PWM Duty Cycle 1 PWM V 24V 2.4V GA824P1H61(611) 8mm Low Power Consumption Fan 8mm 44

46 Low Power Consumption Fan 92mm sq. San Ace 92 25mm thick (GA type), 38mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 125g GA type Specifications To order a ribless type, replace the last digits of a model number with digits in parenthesis. Model No. 9GA912P4J3(31) 9GA912P4G3(31) 9GA912P4S3(31) 9GA924P4J3(31) 9GA924P4G3(31) 9GA924P4S3(31) Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , , to , , , , , to 7 6, , to , , , , PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm Mounting Hole With ribs Lead Wire AWG26 UL Rotating Direction Air Flow Direction 45

47 Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side Low Power Consumption Fan 92mm Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-11G Outlet side Model 19-99E 19-99H mm Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI

48 Low Power Consumption Fan 92mm sq. San Ace mm Mass 125g Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure DC 12V PWM Duty Cycle 1% 5% % Static Pressure DC 12V PWM Duty Cycle 1% 5% % Static Pressure DC 12V PWM Duty Cycle 1% 5% % Air Flow Air Flow Air Flow 9GA912P4J3(31) 9GA912P4G3(31) 9GA912P4S3(31) Operating Voltage Range Static Pressure Static Pressure PWM PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle V V 13.8V V 12V V V.2 1.2V 4 1.2V m /min Air Flow Air Flow Air Flow 9GA912P4J3(31) 9GA912P4G3(31) 9GA912P4S3(31) Static Pressure PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage DC12V DC12V PWM 25kHz Frequency 25kHz 5, 5,min -1 4, 3, 2, 1,5min -1 1, Rotation min Speed min -1-1 Voltage DC12VPWM DC12V Frequency 25kHz PWM 25kHz 5, 4, 3, 2, 1,5min -1 1, 4,4min -1 Rotation min Speed min -1-1 Voltage DC12V DC12V PWM PWM 25kHz Frequency 25kHz 5, 4, 3, 2, 1,5min -1 1, 3,8min -1 1 PWM PWM % Duty Cycle % 9GA912P4J3(31) 1 PWM PWM % Duty Cycle % 9GA912P4G3(31) 1 PWM PWM % Duty Cycle % 9GA912P4S3(31) 47

49 Static Pressure DC 24V PWM Duty Cycle 1% 5% % Static Pressure DC24V PWM Duty Cycle 1% 5% % Static Pressure DC24V PWM Duty Cycle 1% 5% % Low Power Consumption Fan 92mm Air Flow Air Flow Air Flow 9GA924P4J3(31) 9GA924P4G3(31) 9GA924P4S3(31) Static Pressure Static Pressure PWM PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle V V 27.6V V 24V V V.2 2.4V 4 2.4V m /min Air Flow Air Flow Air Flow 9GA924P4J3(31) 9GA924P4G3(31) 9GA924P4S3(31) Static Pressure Rotation min Speed min -1-1 Voltage DC24V DC24V PWM 25kHz Frequency 25kHz 5, 5,min -1 4, 3, 2, 1,5min -1 1, Rotation min Speed min -1-1 Voltage DC24V DC24V PWM PWM 25kHz Frequency 25kHz 5, 4, 3, 2, 1, 1,5min -1 4,4min -1 Rotation min Speed min -1-1 Voltage DC24V DC24V PWM PWM 25kHz Frequency 25kHz 5, 4, 3, 2, 1,5min -1 1, 3,8min -1 92mm 1 PWM PWM % Duty Cycle % 1 PWM PWM % Duty Cycle % 1 PWM PWM % Duty Cycle % 9GA924P4J3(31) 9GA924P4G3(31) 9GA924P4S3(31) 48

50 Low Power Consumption Fan 92mm sq. San Ace 92 25mm thick (GA type), 38mm thick (GA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 245g GA type Specifications To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , ,/6 9GA912P1H3(31) to , to 7 (7,/4 ) 9GA948P1H3 Note1) to , , Note 1: Rated voltage 48V fans do not rotate when PWM duty cycle is %. Note 2: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm (With ribs) Mounting Hole Lead Wire AWG24 UL (1) (4) 38.5 (4) Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

51 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Model 19-99E 19-99H Outlet side Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-11G Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI Low Power Consumption Fan 92mm Air Flow - Static Pressure Characteristics PWM Duty Cycle Operating Voltage Range PWM Duty - Speed Characteristics Example Static Pressure DC 12V PWM Duty Cycle 1% 5% % GA912P1H3(31) Static Pressure PWM PWM 1% Duty Cycle V 12V 1.2V GA912P1H3(31) 5 Rotation min Speed min -1-1 Voltage DC12V DC12V PWM PWM 25kHz Frequency 25kHz 1, 9,7min -1 8, 6, 4, 2,5min -1 2, 1 PWM PWM % Duty Cycle % 9GA912P1H3(31) % DC 48V PWM Duty Cycle 1% PWM PWM 1 Duty Cycle V 48V 4.8V Rotation min Speed min -1-1 Voltage DC48V DC48V PWM 25kHz Frequency 25kHz 1, 9,7min -1 8, 6, 4, 2, 1 PWM PWM % Duty Cycle % 92mm 9GA948P1H3 9GA948P1H3 9GA948P1H3 5

52 Silent Fan 6mm sq. San Ace 6 25mm thick (S type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 55g Specifications Model No. S type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9S612S41(411) , to S612H41(411) , S612F41(411) , to S612M41(411) , to 7 4, Available upon request for all the Without Sensor Pulse Sensor models above. Lock Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm

53 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G Silent Fan 6mm 7.7 Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI Air Flow - Static Pressure Characteristics Static Pressure S speed 13.8V 12V 5V H speed 13.8 V 12 V 5V F speed 13.8 V 12 V 6V S612S41(411) S612H41(411) S612F41(411) M speed 13.8V 12V 6V 6mm Air Flow 9S612M41(411) 52

54 Silent Fan 8mm sq. San Ace 8 25mm thick (S type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 75g Specifications Model No. S type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9S812H41(411) 5. to , S812F41(411) , to S812M41(411) , S812L41(411) 6. to , S824M41(411) , to S824L41(411) , Available upon request for all the Without Sensor Pulse Sensor models above. Lock Sensor PWM Control 1 to 7 4, Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm

55 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side Silent Fan 8mm Model 19-49E 19-49H 11.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Air Flow - Static Pressure Characteristics H speed 13.2V 12V 5V F speed 13.8V 12V 5V M speed 13.8V/26.4V 12V/24V 5V/1V S812H41(411) S812F41(411) S812M41(411) 9S824M41(411).2 5 L speed V/26.4V 12V/24V 6V/1V 8mm S812L41(411) 9S824L41(411) 54

56 Silent Fan 92mm sq. San Ace 92 25mm thick (S type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 1g Specifications Model No. S type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9S912F41(411) , to S912M41(411) , S912L41(411) 6. to , S924F41(411) , S924M41(411) to , S924L41(411) , to 7 4, Available upon request for all the Without Sensor Pulse Sensor models above. Lock Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm

57 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-11G Outlet side Silent Fan 92mm Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI Air Flow - Static Pressure Characteristics F speed V 12V 1. 5V S912F41(411) M speed 13.8V 12V 5V S912M41(411) L speed V 12V.8 6V Air Flow 9S912L41(411) Static Pressure F speed M speed L speed 26.4V 24V 14V S924F41(411) Static Pressure V 24V 14V S924M41(411) Static Pressure V 24 V 14 V Air Flow 9S924L41(411) 92mm 56

58 Silent Fan 12 mm sq. San Ace 12 25mm thick (S type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 14g Specifications Model No. S type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9S1212H41(411) 5. to , to 6 9S1212F41(411) 5. to , S1212M41(411) 6. to , to 7 9S1212L41(411) 7. to , Available upon request for all the Without Sensor Pulse Sensor models above. Lock Sensor PWM Control Dimensions Unit : mm With ribs Please inquire as the availability of these functions depend on the model. 4, Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

59 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side Resin finger guards Model 19-1G Silent Fan 12mm Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI Air Flow - Static Pressure Characteristics H speed 13.2V 12V 5V F speed 13.8V 12V 5V M speed 13.8V 12V 6V S1212H41(411) 9S1212F41(411) 9S1212M41(411).15 4 L speed 12mm V 12V 7V S1212L41(411) 58

60 DC Fan 36mm sq. San Ace 36 28mm thick GV type General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 46g Specifications GV type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9GV3612J , to GV3612G , to 6 4, Available upon request for all the Please inquire as the availability of these functions depend Without Sensor Pulse Sensor models above. Lock Sensor PWM Control on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG28 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

61 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver DC Fan 36mm Air Flow - Static Pressure Characteristics J speed 13.2V 12V 7V Air Flow 9GV3612J G speed 13.2V 12V 7V GV3612G31 36mm 6

62 DC Fan 38mm sq. San Ace 38 28mm thick GV type General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 5g Specifications Model No. GV type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9GV312K31(311) , GV312J31(311) 7 to , GV312G31(311) , GV312E31(311) , to GV312H31(311) , Available upon request for all the Without Sensor Pulse Sensor models above. Lock Sensor PWM Control 1 to 6 4, Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Rotating Direction Lead Wire AWG26 UL17 Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

63 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver DC Fan 38mm Air Flow - Static Pressure Characteristics Static Pressure K speed 13.2V 7V 12V GV312K31(311) J speed 13.2V 12V 7V GV312J31(311) G speed V 25 12V 2 7V mm 9GV312G31(311) E speed 13.2V 12 V 4.5V GV312E31(311) Static Pressure V H speed 13.2V 12V GV312H31(311) 62

64 DC Fan 4mm sq. San Ace 4 1mm thick, 15mm thick, 2mm thick 28mm thick (GE type) 28mm thick (GV type), 28mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 4 4 1mm Mass 19g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P45H , to P45M , P412H , to P412M , to 6 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Rotating Direction Lead Wire AWG26 UL17 Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

65 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Air Flow - Static Pressure Characteristics H speed 5.5V 5V 4.5V M speed 5.5V 5V 4.5V H speed 13.8V 12V 7V P45H P45M P412H M speed 13.8V 12V 7V P412M91 4mm DC Fan 4mm 64

66 DC Fan 4mm sq. San Ace 4 1mm thick, 15mm thick, 2mm thick 28mm thick (GE type) 28mm thick (GV type), 28mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 32g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P45H , to to 5.5 6, 19P45M , P412R71 7 to , , 19P412S , to 7 19P412H to , , 19P412M , P424H to , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Rotating Direction 1 Lead Wire AWG24 UL17 Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

67 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Air Flow - Static Pressure Characteristics V 1 5V 4.5V 5 H speed P45H M speed V 6 5 V V P45M71.3 Static Pressure R speed 13.8V 12V 7V P412R S speed 13.8V 12V 1.2V H speed 13.8V/27.6V 12V/24V 1.2V/2.4V M speed 13.8V 12V 1.2V P412S71 19P412H71 19P424H71 19P412M71 4mm DC Fan 4mm 66

68 DC Fan 4mm sq. San Ace 4 1mm thick, 15mm thick, 2mm thick 28mm thick (GE type) 28mm thick (GV type), 28mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 4 4 2mm Mass 45g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P45J , , 19P45H , to to 7 19P45F , , 19P45M , P412G , , 1 to 6 19P412D , P412E61 7 to , P412H , , 1 to 7 19P412F , P412M61 8 to , P424D61 12 to , to 6 4, 19P424H61 12 to , P424F61 14 to , to 7 6, 19P424B to , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole 4 Lead Wire AWG24 UL Rotating Direction Air Flow Direction 67

69 Reference dimension of mounting holes and vent opening Unit : mm DC Fan 4mm mm Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver 68

70 DC Fan 4mm sq. San Ace mm Mass 45g Air Flow - Static Pressure Characteristics J speed 5.5 V 5 V 4.5 V Air Flow 19P45J H speed 5.5V 5V 4.5V P45H F speed 5.5V 5V 4.5V P45F61 Static Pressure E speed 13.8V 12V 7V H speed 13.8V 12V 7V F speed 13.8V/27.6V 12V/24V 7V/14V Air Flow 19P412E61 B speed P412H P412F61 19P424F61 Static Pressure V 24V 2.4V Air Flow 19P424B61 69

71 Static Pressure V V V Air Flow D speed 13.8V 12V 7V Air Flow 4mm DC Fan 4mm V 5V 4.5V Air Flow 19P45M61 M speed M speed V 12V 8V P412M P412G61 G speed D speed V 24V 12V P424D61 19P412D H speed 27.6V 24V 12V P424H61 7

72 DC Fan 4mm sq. San Ace 4 1mm thick, 15mm thick, 2mm thick 28mm thick (GE type) 28mm thick (GV type), 28mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Aluminum,Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 55g Specifications Low vibration GE type Model No. 9GE412P3K3 9GE412P3J3 9GE412P3G3 Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , , to , , to 6 4, , , PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the Please inquire as the availability of these functions depend models above. Lock Sensor on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG28 UL161 Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver

73 Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure % % DC 12V PWM Duty Cycle 1% Air Flow 9GE412P3K mm %.2 PWM Duty Cycle 1% 5%.4.6 DC 12V GE412P3J3 Static Pressure DC 12V PWM Duty Cycle 1% 5% % Air Flow 9GE412P3G3 DC Fan 4mm Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle V 12V 1.8V GE412P3K PWM PWM 1 Duty Cycle V 12V 1.8V GE412P3J3 Static Pressure PWM PWM 1 Duty Cycle V 12V 1.8V GE412P3G3 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 16,5min -1 15, 1, Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 15min -1 1, 5, 5, 5, 3,min min -1 2,4min PWM PWM % Duty Cycle % PWM PWM % Duty Cycle % PWM PWM % Duty Cycle % Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 13,min -1 1, 9GE412P3K3 9GE412P3J3 9GE412P3G3 72

74 DC Fan 4mm sq. San Ace 4 1mm thick, 15mm thick, 2mm thick 28mm thick (GE type) 28mm thick (GV type), 28mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 5g Specifications Model No. GV type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9GV412K31(311) 1.8 to , GV412J31(311) , to GV412G31(311) 7 to , GV412C31(311) , to 7 Available upon request for all the Without Sensor Pulse Sensor models above. Lock Sensor PWM Control Please inquire as the availability of these functions depend on the model. 4, Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG26 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

75 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Air Flow - Static Pressure Characteristics Static Pressure K speed 12.6 V 12 V 1.8 V GV412K31(311) J speed V 3 12V V GV412J31(311) G speed V 3 12 V V GV412G31(311) Static Pressure C speed V V V Air Flow.5 9GV412C31(311) 4mm DC Fan 4mm 74

76 DC Fan 4mm sq. San Ace 4 1mm thick, 15mm thick, 2mm thick 28mm thick (GE type) 28mm thick (GV type), 28mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 52g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P45H , , to P45F , to 7 6, 19P412K313 8 to , P412J , to P412G , to 6 4, 19P412B , P412H313 7 to , P412F , to 7 6, 19P412M to , P424J , P424G to , to 6 4, 19P424B , P424H to , P424F to , to 7 6, Available upon request for all the Please inquire as the availability of these functions depend Without Sensor Pulse Sensor models above. Lock Sensor PWM Control on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL17 Rotating Direction Air Flow Direction 75

77 Reference dimension of mounting holes and vent opening Unit : mm DC Fan 4mm Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver mm 76

78 DC Fan 4mm sq. San Ace mm Mass 52g Air Flow - Static Pressure Characteristics K speed 13.2V 12V 8V P412K313 J speed 13.2V 12V 7V 19P412J J speed 26.4V 24V 12V 19P424J B speed H speed H speed 26.4V 24V 12V V 5V 4.5V V 12V 7V Air Flow 19P424B313 19P45H313 19P412H M speed 13.8V 12V 1.2V P412M313 77

79 1. 25 G speed G speed B speed V 12V 7V V 24V 12V V 12V 7V Air Flow 19P412G313 19P424G313 19P412B H speed F speed F speed 27.6V 24V 12V Air Flow 19P424H V 5V 4.5V P45F V/27.6V 12V/24V 7V/14V P412F313 19P424F313 4mm DC Fan 4mm 78

80 DC Fan 52mm sq. San Ace 52 15mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 55g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P55M to , , 19P512A to , , 1 to 7 19P512H , to , 19P512M , P524A , to 6 4, 19P524H to , to 7 6, 19P524M , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

81 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model E Surface treatment Nickel-chrome plating silver Outlet side DC Fan 52mm Air Flow - Static Pressure Characteristics A speed 13.8V 12V 1.2V P512A71 M speed 13.8V/27.6V 12V/24V 7V/14V V 24V 14V P524A71 M speed 5.5V 5V 4.5V H speed 13.8V/27.6V 12V/24V 7V/14V P512H71 19P524H P512M71 19P524M P55M71 52mm A speed 8

82 DC Fan 6mm sq. San Ace 6 15mm thick, 2mm thick, 25mm thick (G type) 25mm thick, 25mm thick (San Cooler) 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 6g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P65H , to P65M , to 7 6, 19P612K , to to P612S , , 19P612H to , to 7 19P612M , to P612B , , 19P624J , to 6 4, 19P624S71 14 to , P624H , to 7 6, 19P624M to , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction Air Flow Direction Options Unit : mm Finger guards Model E H 53 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G

83 Options Unit : mm Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI DC Fan 6mm Air Flow - Static Pressure Characteristics S speed 13.8V 12V 1.2V P612S H speed 5.5V 5V 4.5V P65H K speed 13.8V 12 V 1.2V Air Flow 19P612K H speed 13.8V/27.6V 12V/24V 7V/14V P612H71 19P624H71 M speed 5.5V 5V 4.5V 19P65M M speed 13.8V/27.6V 12V/24V 1.2V/2.4V P612M71 19P624M71 Static Pressure B speed 13.8V 12V 1.2V Static Pressure J speed 27.6V 24V 14V Static Pressure S speed 27.6V 24V 14V 6mm Air Flow 19P612B Air Flow 19P624J Air Flow 19P624S71 82

84 DC Fan 6mm sq. San Ace 6 15mm thick, 2mm thick, 25mm thick (G type) 25mm thick, 25mm thick (San Cooler) 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 6 6 2mm Mass 9g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P612W61 6 to , P612H , to P612M , , 19P624W61 12 to , to 7 19P624H , to P624M , P648H to , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

85 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G DC Fan 6mm 7.7 Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI Air Flow - Static Pressure Characteristics V 16V 12V V 3V 24V P624W P612W Wide range H speed 53V 48V 43V P648H Wide range M speed 13.8V/27.6V 12V/24V 1.2V/2.4V P612M61 19P624M H speed 13.8V/27.6V 12V/24V 1.2V/2.4V P612H61 19P624H mm

86 DC Fan 6mm sq. San Ace 6 15mm thick, 2mm thick, 25mm thick (G type) 25mm thick, 25mm thick (San Cooler) 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 9g Specifications Model No. 9G612P4S1(11) 9G612P4H1(11) G type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Range Expected Life Note) V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , , to , , , G624P4S1(11) , to , G624P4H1(11) , , G648P4S1(11) to , Note: Expected life at 4 ambient is just reference value. Available upon request for all the models above. 1 to 7 4,/6 (7,/4 ) PWM Frequency 25kHz Dimensions Unit : mm With ribs 4-Ø4.5.3 Mounting Hole Reference dimension of mounting holes and vent opening Unit : mm (1) Lead Wire AWG26 UL143 (3) 25.5 (3) Rotating Direction Air Flow Direction Options Unit : mm Finger guards Model E H 53 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G

87 Options Unit : mm Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI DC Fan 6mm Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure Static Pressure % DC 12V / DC24V PWM Duty Cycle 1% 5% Static Pressure % DC 12V / DC24V PWM Duty Cycle 1% 5% Air Flow Air Flow 9G612P4S1(11) 9G624P4S1(11) Operating Voltage Range PWM V/27.6V 12V/24V 1.2V/2.4V Static Pressure % % DC 48V PWM Duty Cycle 1% PWM Duty Cycle 1 PWM Duty Cycle 1 PWM Duty Cycle V/27.6V 12V/24V 1.2V/2.4V Static Pressure PWM V/72V Air Flow Air Flow Air Flow 9G612P4S1(11) 9G624P4S1(11) PWM Duty - Speed Characteristics Example 9G612P4H1(11) 9G624P4H1(11) 9G612P4H1(11) 9G624P4H1(11) Static Pressure G648P4S1(11) PWM 1 36V 9G648P4S1(11) Rotation min Speed min -1-1 Voltage 12V/24V DC12V/DC24V DC Voltage 12V/24V DC12V/DC24V Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz PWM 25kHz Frequency 25kHz PWM 25kHz Frequency 25kHz 12, 12, 1, 11, 11,min -1 9,5min -1 11, 1, 9, 1, 9, 8, 9, 11,min -1 8, 7, 8, 7, 6, 7, 6, 5, 6, 5, 4, 5, 4, 4, 3, 3,3min -1 3, 2,85min -1 3, 3,3min -1 2, 2, 2, 1, 1, 1, PWM PWM % Duty Cycle % PWM PWM % Duty Cycle % PWM PWM % Duty Cycle % 9G612P4S1(11) 9G624P4S1(11) Rotation min Speed min G612P4H1(11) 9G624P4H1(11) Rotation min Speed min G648P4S1(11) 86 6mm

88 DC Fan 6mm sq. San Ace 6 15mm thick, 2mm thick, 25mm thick (G type) 25mm thick, 25mm thick (San Cooler) 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 9g Specifications Model No. To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19R65H41(411) , to 7 19R65F41(411) to , to 6 6, 19R65M41(411) , to 7 19R612J41(411) , to 6 4, 1.8 to R612G41(411) , R612D41(411) 1.2 to , R612S41(411) , R612H41(411) 6 to , to 7 6, 19R612F41(411) , R612M41(411) 7 to , R624J41(411) 21.6 to , to 6 19R624G41(411) 2.4 to , , 19R624D41(411) , R624S41(411) , to to 7 19R624H41(411) , , 19R624F41(411) , R624M41(411) 14 to , R648J41(411) 43.2 to , R648G41(411) to , to 6 4, 19R648H41(411) 4 to , to 7 6, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction 87

89 Reference dimension of mounting holes and vent opening Unit : mm DC Fan 6mm Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G mm Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI 88

90 DC Fan 6mm sq. San Ace mm Mass 9g Air Flow - Static Pressure Characteristics J speed G speed G speed 13.2V/26.4V/52.8V 12V/24V/48V 1.8V/21.6V/43.2V R612J41(411) 19R624J41(411) 19R648J41(411) V 12V 1.8V R612G41(411) V 24V 2.4V R624G41(411) S speed H speed H speed 13.8V/27.6V 12V/24V 6V/12V R612S41(411) 19R624S41(411) V 5V 4.5V R65H41(411) V/27.6V 12V/24V 6V/12V R612H41(411) 19R624H41(411) M speed 5.5V 5V 4.5V M speed 13.8V/27.6V 12V/24V 7V/14V R65M41(411) R612M41(411) 19R624M41(411) 89

91 G speed 53V 48V 43V Air Flow 19R648G41(411) D speed 13.8V 12V 1.2V R612D41(411) D speed 27.6V 24V 12V R624D41(411) H speed F speed F speed 53V 48V 4V R648H41(411) inch H2O V 5V 4.5V R65F41(411) inch H2O V/27.6V 12V/24V 6V/12V R612F41(411) 19R624F41(411) 6mm DC Fan 6mm 9

92 DC Fan 6mm sq. San Ace 6 15mm thick, 2mm thick, 25mm thick (G type) 25mm thick, 25mm thick (San Cooler) 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 8g Specifications Model No. San Cooler To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9A612G41(411) 6 to , to 6 3, 9A612S41(411) , A612H41(411) 12 6 to , A612F41(411) , to 7 4, 9A612M41(411) 7 to , A624G41(411) 12 to , to 6 3, 9A624S41(411) , A624H41(411) to , A624F41(411) , to 7 4, 9A624M41(411) 14 to , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

93 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G DC Fan 6mm 7.7 Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI Air Flow - Static Pressure Characteristics G speed 6V 13.2V 12V V A624G41(411) A612G41(411) G speed 27.6V 24V S speed 13.8V/27.6V 12V/24V 6V/12V A612S41(411) 9A624S41(411) H speed 13.8V/27.6V 12V/24V 6V/12V V/12V 13.8V/27.6V 12V/24V A612H41(411) 9A624H41(411) F speed 9A612F41(411) 9A624F41(411) M speed 13.8V/27.6V 12V/24V 7V/14V A612M41(411) 9A624M41(411) 92 6mm

94 DC Fan 6mm sq. San Ace 6 15mm thick, 2mm thick, 25mm thick (G type) 25mm thick, 25mm thick (San Cooler) 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 13g Specifications GVtype To order a ribless type, replace the last digits of a model number with digits in parenthesis. Model No. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Range Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h 9GV612P1G3(31) , , GV612P1H3(31) , to , GV612P1M3(31) , , to 7 4, 9GV612P1L1(11) Note) 1.8 to , GV624P1G3(31) to , , GV648P1H3(31) to , , Note : Fan does not rotate when PWM duty cycle is %. PWM Frequency 25kHz Available upon request for all the Without Sensor Pulse Sensor PWM Control models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole With ribs Lead Wire AWG26 UL17 9GV6**P1H3, Model: 9GV612P1M3 UL143 9GV6**P1G3 Model: Rotating Direction Air Flow Direction 93

95 Reference dimension of mounting holes and vent opening Unit : mm DC Fan 6mm Options Unit : mm Finger guards Model E H 53 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI mm 94

96 DC Fan 6mm sq. San Ace mm Mass 13g Air Flow - Static Pressure Characteristics PWM Duty Cycle % % DC 12V PWM Duty Cycle 1% GV612P1G3(31) % % DC 12V PWM Duty Cycle 1% GV612P1H3(31) % % DC 12V PWM Duty Cycle 1% GV612P1M3(31) Operating Voltage Range PWM PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle V 12V 8V V 12V V GV612P1G3(31) 9GV612P1H3(31) 9GV612P1M3(31) V 12 V V PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 18, 16, 16,min -1 14, 12, 1, 8, 6, 4, 3,1min -1 2, 1 PWM PWM % Duty Cycle % 9GV612P1G3(31) min Rotation Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 16, 14, 12, 1, 8, 6, 4, 2, 2,7min -1 14,5min -1 1 PWM PWM % Duty Cycle % 9GV612P1H3(31) Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 14, 13,min -1 12, 1, 8, 6, 4, 2,5min 2, -1 1 PWM PWM % Duty Cycle % 9GV612P1M3(31) 95

97 DC Fan 6mm Static Pressure DC 12V PWM Duty Cycle 1% 5% Static Pressure DC 24V PWM Duty Cycle 1% 5% % Static Pressure DC 48V PWM Duty Cycle 1% 5% % GV612P1L1(11) GV624P1G3(31) Air Flow 9GV648P1H3(31) Static Pressure PWM PWM 1 Duty Cycle V V V GV612P1L1(11) Static Pressure PWM PWM 1 Duty Cycle V 24V 2.4V Air Flow 9GV624P1G3(31) Static Pressure PWM PWM 1 Duty Cycle 1 57V 48V 38V Air Flow 9GV648P1H3(31) Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 11, 1, 1,min -1 9, 8, 7, 6, 5, 4, 3, 2, 1, 1 PWM PWM % Duty Cycle % 9GV612P1L1(11) min Rotation Speed min -1-1 Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz 16, 14, 12, 1, 8, 6, 6,min -1 16,min -1 4, 2, 1 PWM PWM % Duty Cycle % 9GV624P1G3(31) Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 16, 14,5min -1 14, 12, 1, 8, 6, 6,min -1 4, 2, 1 PWM PWM % Duty Cycle % 9GV648P1H3(31) 6mm 96

98 DC Fan 6mm sq. San Ace 6 15mm thick, 2mm thick, 25mm thick (G type) 25mm thick, 25mm thick (San Cooler) 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 11g Specifications Model No. G type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9G612G11(111) , to G612S11(111) , G624G11(111) , G624S11(111) to , G624H11(111) , G648G11(111) , to G648S11(111) , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm 97

99 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI Air Flow - Static Pressure Characteristics G speed 13.8V/27.6V/55.2V.8 12V/24V/48V 7V/14V/28V V/27.6V/55.2V V/24V/48V 7V/14V/28V G612G11(111) 9G624G11(111) 9G648G11(111) S speed G612S11(111) 9G624S11(111) 9G648S11(111) H speed 14V 27.6V 24V G624H11(111) 6mm DC Fan 6mm 98

100 DC Fan 8mm sq. San Ace 8 15mm thick, 2mm thick, 25mm thick (GV type) 25mm thick, 25mm thick (San Cooler), 32mm thick 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 68g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P812H , , 12 7 to P812M , , 1 to 7 19P824H , , to P824M , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

101 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side DC Fan 8mm Model 19-49E 19-49H 11.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI V/27.6V V/24V V/14V Air Flow 8mm Air Flow - Static Pressure Characteristics H speed 19P812H71 19P824H M speed V/27.6V.4 12V/24V 7V/14V P812M71 19P824M71 1

102 DC Fan 8mm sq. San Ace 8 15mm thick, 2mm thick, 25mm thick (GV type) 25mm thick, 25mm thick (San Cooler), 32mm thick 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 8 8 2mm Mass 1g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P812C , to 6 19P812H to , P812M , to 7 19P824H , to P824M , P848C , to to P848H , to 6 Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. 6, 4, Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL17 Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

103 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side DC Fan 8mm Model 19-49E 19-49H 11.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Air Flow - Static Pressure Characteristics C speed V 12 V 1.2V V/27.6V 12V/24V 1.2V/2.4V Air Flow 19P812C61 H speed 19P812H61 19P824H M speed V/27.6V 12V/24V 1.2V/2.4V 19P812M61 19P824M C speed V 5 48V 4 38V P848C61 H speed V V V Air Flow 19P848H61 8mm 12

104 DC Fan 8mm sq. San Ace 8 15mm thick, 2mm thick, 25mm thick (GV type) 25mm thick, 25mm thick (San Cooler), 32mm thick 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 125g Specifications GV type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , GV812P4K3(31) , to , GV812P4J3(31).7.8 1, to 7 4, , GV824P4K1(11) to , , GV848P4K3(31) to , Available upon request for all the Without Sensor Pulse Sensor PWM Control models above. Lock Sensor Please inquire as the availability of these functions depend on the model. PWM Frequency 25kHz Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG26 UL Rotating Direction Air Flow Direction 13

105 11.2 Reference dimension of mounting holes and vent opening Unit : mm mm DC Fan 8mm Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI

106 DC Fan 8mm sq. San Ace mm Mass 125g Air Flow - Static Pressure Characteristics PWM Duty Cycle.8 2 DC 12V 12 DC 12V.8 2 DC 24V % 5% PWM Duty Cycle 1% GV812P4K3(31) % 5% PWM Duty Cycle 1% GV812P4J3(31) PWM Duty Cycle 1% % 5% GV824P4K1(11) Operating Voltage Range PWM 1 Duty Cycle 1 PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle V 12 V 1.2 V V 12V 1.2V Air Flow Air Flow Air Flow 9GV812P4K3(31) 9GV812P4J3(31) 9GV824P4K1(11) V 24V 2.4V PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 6, 5,6min -1 5, 4, 3, 2, 1,4min -1 1, 1 PWM PWM % Duty Cycle % 9GV812P4K3(31) Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 6, 5, 4,5min -1 4, 3, 2, 1, 1,2min -1 1 PWM PWM % Duty Cycle % 9GV812P4J3(31) Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM 25kHz Frequency 25kHz 6 5,6min ,4min -1 1 PWM PWM % Duty Cycle % 9GV824P4K1(11) 15

107 DC Fan 8mm.8 2 DC 48V Static Pressure PWM Duty Cycle 1% 5% % Air Flow 9GV848P4K3(31).8 2 PWM PWM 1 Duty Cycle Static Pressure V 48V 43V Air Flow 2.5 9GV848P4K3(31) Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 6, 5,6min -1 5, 4, 3, 2, 1,5min -1 1, 1 PWM PWM % Duty Cycle % 9GV848P4K3(31) 8mm 16

108 DC Fan 8mm sq. San Ace 8 15mm thick, 2mm thick, 25mm thick (GV type) 25mm thick, 25mm thick (San Cooler), 32mm thick 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 11g Specifications Model No. To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19R85F41(411) , to R85M41(411) , to 7 6, 19R812G41(411) 1.8 to , R812E41(411) , to 6 4, 19R812S41(411) , R812H41(411) 12 6 to , R812F41(411) , to 7 6, 19R812M41(411) , R812L41(411) 7 to , R824G41(411) 2.4 to , to 6 4, 19R824S41(411) , R824H41(411) , to R824F41(411) , to 7 6, 19R824M41(411) , R824L41(411) 14 to , R848K41(411) , to 6 4, to R848S41(411) , to 7 6, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction 17

109 Reference dimension of mounting holes and vent opening Unit : mm mm Outlet side DC Fan 8mm Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI

110 DC Fan 8mm sq. San Ace mm Mass 11g Air Flow - Static Pressure Characteristics K speed G speed G speed V 48V 4.8V V 8 12V 7 1.8V Air Flow V 8 24V 7 2.4V R848K41(411) 19R812G41(411) 19R824G41(411) H speed F speed F speed 13.8V/27.6V 12V/24V 6V/12V Air Flow V 5V 4.5V Air Flow V/27.6V 12V/24V 6V/12V Air Flow 19R812H41(411) 19R824H41(411) 19R85F41(411) 19R812F41(411) 19R824F41(411) 19

111 8mm DC Fan 8mm V/27.6V 12V/24V 6V/12V V.5 48V 4.5V R812S41(411) 19R824S41(411) S speed 5.5V 5V 4.5V R848S41(411) S speed 13.8V/27.6V 12V/24V 6V/12V Static Pressure V 13.8V 12V R812E41(411) E speed M speed M speed L speed V/27.6V 12V/24V 7V/14V R85M41(411) 19R812M41(411) 19R824M41(411) 19R812L41(411) 19R824L41(411) 11

112 DC Fan 8mm sq. San Ace 8 15mm thick, 2mm thick, 25mm thick (GV type) 25mm thick, 25mm thick (San Cooler), 32mm thick 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 9g Specifications Model No. San Cooler To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9A812G41(411) 6 to , to 6 3, 9A812S41(411) , A812H41(411) , to A812F41(411) , to 7 4, 9A812M41(411) , A812L41(411) 7 to , A824G41(411) 12 to , to 6 3, 9A824S41(411) , A824H41(411) , to A824F41(411) , to 7 4, 9A824M41(411) , A824L41(411) 14 to , Available upon request for all the Please inquire as the availability of these functions depend Without Sensor Pulse Sensor models above. Lock Sensor PWM Control on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

113 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side DC Fan 8mm Model 19-49E 19-49H 11.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Air Flow - Static Pressure Characteristics G speed 13.2V/26.4V 12V/24V 6V/12V inch H2O Pa S speed V/27.6V 12V/24V 6V/12V H speed V/27.6V 12V/24V 6V/12V A812G41(411) 9A824G41(411) 9A812S41(411) 9A824S41(411) 9A812H41(411) 9A824H41(411) F speed V/27.6V 12V/24V 6V/12V M speed 13.8V/27.6V 12V/24V 6V/12V L speed 13.8V/27.6V 12V/24V 7V/14V mm 9A812F41(411) 9A824F41(411) 9A812M41(411) 9A824M41(411) 9A812L41(411) 9A824L41(411) 112

114 DC Fan 8mm sq. San Ace 8 15mm thick, 2mm thick, 25mm thick (GV type) 25mm thick, 25mm thick (San Cooler), 32mm thick 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 15g Specifications Model No. To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P812A21(211) 6 to , to 55 4,(+55 ) 19P812H21(211) , , 1.2 to to 7 19P812M21(211) , , 19P824A21(211) 12 to , to 6 4, 19P824H21(211) , to P824M21(211) , to 7 6, 19P848H21(211) to , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

115 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side DC Fan 8mm Model 19-49E 19-49H 11.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Air Flow - Static Pressure Characteristics A speed 13.2V/26.4V 12V/24V 6V/12V H speed V/27.6V 12V/24V 1.2V/2.4V H speed.5 53V 48V 43V P812A21(211) 19P824A21(211) 19P812H21(211) 19P824H21(211) 19P848H21(211).12 3 M speed V/27.6V 12V/24V 1.2V/2.4V 8mm P812M21(211) 19P824M21(211) 114

116 DC Fan 8mm sq. San Ace 8 15mm thick, 2mm thick, 25mm thick (GV type) 25mm thick, 25mm thick (San Cooler), 32mm thick 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 22g Specifications GV type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Model No. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , GV812P1G3(31) , to , GV812P1H3(31) , , GV812P1F3(31) , to to 7 4, , GV812P1M3(31) , GV824P1G3(31) to , , GV848P1G3(31) to , , Available upon request for all the Without Sensor Pulse Sensor PWM Control models above. Lock Sensor Please inquire as the availability of these functions depend on the model. PWM Frequency 25kHz Dimensions Unit : mm Mounting Hole With ribs Reference dimension of mounting holes and vent opening Unit : mm Lead Wire AWG24 UL Rotating Direction Air Flow Direction 115

117 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side DC Fan 8mm Model 19-49E 19-49H 11.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI mm

118 DC Fan 8mm sq. San Ace mm Mass 22g Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V DC 12V DC 12V PWM Duty Cycle 1% 5% % PWM Duty Cycle 1% 5% % PWM Duty Cycle 1% 5% % GV812P1G3(31) GV812P1H3(31) GV812P1F3(31) Operating Voltage Range PWM PWM 1 Duty Cycle PWM PWM 1 Duty Cycle PWM PWM 1 Duty Cycle V 12V 1.8V V 12V 1.8V V 12V 1.2V GV812P1G3(31) Air Flow 9GV812P1H3(31) GV812P1F3(31) PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 11, 1, 1,2min -1 9, 8, 7, 6, 5, 4, 3, 3,min -1 2, 1, 1 PWM PWM % Duty Cycle % 9GV812P1G3(31) Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 1, 9,7min -1 9, 8, 7, 6, 5, 4, 3, 2,9min -1 2, 1, 1 PWM PWM % Duty Cycle % 9GV812P1H3(31) Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 1, 9, 8, 8,min -1 7, 6, 5, 4, 3, 2, 2,4min -1 1, 1 PWM PWM % Duty Cycle % 9GV812P1F3(31) 117

119 DC Fan 8mm DC 12V DC 24V DC 48V % % PWM Duty Cycle PWM Duty Cycle PWM Duty Cycle 1% % % Air Flow Air Flow 9GV812P1M3(31) Static Pressure % 5% 9GV824P1G3(31) Static Pressure % % 9GV848P1G3(31) PWM 1 PWM PWM 1 Duty Cycle PWM Duty Cycle 1 PWM PWM 1 Duty Cycle V 12V 1.2V Static Pressure V 24V 2.4V Static Pressure V 48V 4.8V Air Flow Air Flow 9GV812P1M3(31) 9GV824P1G3(31) GV848P1G3(31) Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 7, 6, 6,min -1 5, 4, 3, 2, 1, 1,7min -1 1 PWM PWM % Duty Cycle % 9GV812P1M3(31) Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM 25kHz Frequency 25kHz 11, 1, 1,2min -1 9, 8, 7, 6, 5, 4,7min 4, -1 3, 2, 1, 1 PWM PWM % Duty Cycle % 9GV824P1G3(31) Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 11, 1, 1,2min -1 9, 8, 7, 6, 5, 4,7min 4, -1 3, 2, 1, 1 PWM PWM % Duty Cycle % 9GV848P1G3(31) 8mm 118

120 DC Fan 8mm sq. San Ace 8 15mm thick, 2mm thick, 25mm thick (GV type) 25mm thick, 25mm thick (San Cooler), 32mm thick 38mm thick (GV type), 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 17g Specifications Model No. G type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9G812K11(111) 1.8 to , to 6 9G812G11(111) , to G812H11(111) , G824G11(111) , to to 7 9G824H11(111) , G848G11(111) , to G848H11(111) , Available upon request for all the Without Sensor Pulse Sensor models above. Lock Sensor PWM Control Please inquire as the availability of these functions depend on the model. 4, Dimensions Unit : mm Mounting Hole With ribs Lead Wire AWG24 UL Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction Air Flow Direction 119

121 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side DC Fan 8mm Model 19-49E 19-49H 11.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Air Flow - Static Pressure Characteristics K speed V V V V V V 2 1.8V V V m /min G812K11(111) G speed 9G812G11(111) H speed 9G812H11(111) G speed V/55.2V 24V/48V 2.4V/4.8V G824G11(111) 9G848G11(111) H speed 27.6V/55.2V 24V/48V 2.4V/4.8V G824H11(111) 9G848H11(111) 8mm 12

122 DC Fan 92mm sq. San Ace 92 25mm thick, 25mm thick (San Cooler) 32mm thick (G type), 38mm thick (GV type) 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 15g Specifications Model No. To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P912J41(411) 6 to , to 6 19P912W41(411) 6 to , P912H41(411) , P912F41(411) , to P912M41(411) , to 7 19P912L41(411) , P924J41(411) 12 to , to 6 19P924W41(411) 12 to , P924H41(411) , P924F41(411) , to to 7 19P924M41(411) , P924L41(411) , P948H41(411) to , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Options Unit : mm Mounting Hole (4) 25.5 (4) Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Lead Wire AWG24 UL Outlet side (1) Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black

123 Options Unit : mm Resin finger guards Model 19-11G Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI DC Fan 92mm Air Flow - Static Pressure Characteristics J speed V V V Air Flow P912J41(411) Static Pressure J speed 12V 26.4V 24V P924J41(411) inch H2O Pa Wide range 16V 12V 6V Air Flow 19P912W41(411) inch H2O Pa Wide range 3V 24V 12V H speed 13.8V/27.6V 12V/24V 1.2V/2.4V H speed 53V 48V 43V Air Flow 19P924W41(411) P912H41(411) 19P924H41(411) P948H41(411) F speed 13.8V/27.6V 12V/24V 1.2V/2.4V M speed 13.8V/27.6V 12V/24V 1.2V/2.4V L speed 13.8V/27.6V 12V/24V 1.2V/2.4V 92mm P912F41(411) 19P924F41(411) Air Flow 19P912M41(411) 19P924M41(411) P912L41(411) 19P924L41(411) 122

124 DC Fan 92mm sq. San Ace 92 25mm thick, 25mm thick (San Cooler) 32mm thick (G type), 38mm thick (GV type) 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 1g Specifications Model No. San Cooler To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9A912G41(411) , , 1 to 6 9A912S41(411) , A912H41(411) 6 to , A912F41(411) , to 7 9A912M41(411) , , 9A912L41(411) 7 to , A924G41(411) , to 6 3, 9A924S41(411) , A924H41(411) 12 to , A924F41(411) , to 7 4, 9A924M41(411) , A924L41(411) 14 to , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL (4) (4) (1) Rotating Direction Airf Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

125 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-11G Outlet side DC Fan 92mm Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI Air Flow - Static Pressure Characteristics G speed S speed H speed 13.8V/27.6V 6V/12V 12V/24V V/27.6V 12V/24V 6V/12V Air Flow 9A912G41(411) 9A924G41(411) V/27.6V 12V/24V 6V/12V A912S41(411) 9A924S41(411) 9A912H41(411) 9A924H41(411) F speed M speed L speed 13.8V/27.6V 12V/24V 6V/12V V/27.6V 12V/24V 6V/12V Air Flow 9A912F41(411) 9A924F41(411) 9A912M41(411) 9A924M41(411) V/27.6V 12V/24V 7V/14V A912L41(411) 9A924L41(411) 92mm 124

126 DC Fan 92mm sq. San Ace 92 25mm thick, 25mm thick (San Cooler) 32mm thick (G type), 38mm thick (GV type) 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 17g Specifications Model No. G type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9G912A21(211) , G912S21(211) , to G912H21(211) , to 7 9G912M21(211) , G924A21(211) , to 6 9G924S21(211) , to G924H21(211) , G924M21(211) , G948A21(211) , to 7 9G948S21(211) , to G948H21(211) , G948M21(211) , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole With ribs Lead Wire AWG24 UL (1) (4) (4) 32.5 Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

127 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-11G Outlet side DC Fan 92mm Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI Air Flow - Static Pressure Characteristics A speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V Air Flow 9G912A21(211) 9G924A21(211) 9G948A21(211) S speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V G912S21(211) 9G924S21(211) 9G948S21(211) H speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V G912H21(211) 9G924H21(211) 9G948H21(211) M speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V 92mm G912M21(211) 9G924M21(211) 9G948M21(211) 126

128 DC Fan 92mm sq. San Ace 92 25mm thick, 25mm thick (San Cooler) 32mm thick (G type), 38mm thick (GV type) 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 25g Specifications GV type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , GV912P1G3(31) 1.8 to , , GV912P1H3(31) 1.2 to to 7 4, , , GV948P1H3(31) to , PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm With ribs Reference dimension of mounting holes and vent opening Unit : mm Mounting Hole Inlet side Outlet side Lead Wire AWG24 UL Rotating Direction Air Flow Direction Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Outlet side Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black

129 Options Unit : mm Resin finger guards Model 19-11G Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI DC Fan 92mm Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V PWM Duty Cycle 1% % 5% GV912P1G3(31) Operating Voltage Range % DC 12V PWM Duty Cycle 1% 5% GV912P1H3(31) % DC 48V PWM Duty Cycle 1% 5% GV948P1H3(31) PWM PWM 1 Duty Cycle V 12V V 5 6 inch H2O PWM PWM 1 Duty Cycle V GV912P1H3(31) GV912P1G3(31) 12V 1.2V inch H2O PWM PWM 1 Duty Cycle V 48 V 4.8 V GV948P1H3(31) PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 9, 8, 7, 6, 5, 4, 3, 2,9min -1 2, 1, 9,min -1 Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM PWM 25kHz Frequency 25kHz 9, 8, 7, 6, 5, 4, 3, 2,7min -1 2, 1, 8,5min -1 Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM PWM 25kHz Frequency 25kHz 9, 8, 7, 6, 5, 4, 4,min -1 3, 2, 1, 8,5min -1 92mm 1 PWM PWM % Duty Cycle % 9GV912P1G3(31) 1 PWM PWM % Duty Cycle % 9GV912P1H3(31) 1 PWM PWM % Duty Cycle % 9GV948P1H3(31) 128

130 DC Fan 92mm sq. San Ace 92 25mm thick, 25mm thick (San Cooler) 32mm thick (G type), 38mm thick (GV type) 38mm thick (G type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 18g Specifications Model No. G type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9G912G11(111) , to G912H11(111) , G924G11(111) , to G924H11(111) , G948G11(111) , to G948H11(111) , to 6 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL (1) (4) 38.5 (4) Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

131 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-11G Outlet side DC Fan 92mm Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI Air Flow - Static Pressure Characteristics G speed 13.8V 12V 7V G912G11(111) G speed 27.6V/55.2V 24V/48V 2.4V/4.8V G924G11(111) 9G948G11(111) H speed 13.8V 12V 7V Air Flow 9G912H11(111) H speed 27.6V/55.2V 24V/48V 2.4V/4.8V Air Flow 9G924H11(111) 9G948H11(111) 92mm 13

132 DC Fan 12 mm sq. San Ace 12 General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 26g Specifications 25mm thick (GV type), 25mm thick (G type) 38mm thick (GV type),38mm thick (G type) 38mm thick (SG type) GV type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Model No. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h 9GV1212P4G1(11) to , , GV1224P4G1(11) to , , GV1248P4J1(11) 4.8 to , , to 7 4, , GV1248P4G1(11) , to , GV1248P4H1(11) , PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm With ribs Mounting Hole (5) (5) Lead Wire AWG24 UL (1) Rotating Direction Air Flow Direction 131

133 Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side mm DC Fan 12mm 118 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side Resin finger guards Model 19-1G Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI

134 DC Fan 12 mm sq. San Ace mm Mass 26g Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V DC 24V DC 48V Static Pressure PWM Duty Cycle 1% 5% % Static Pressure PWM Duty Cycle 1% 5% % Static Pressure PWM Duty Cycle 1% 5% % Air Flow 9GV1212P4G1(11) Air Flow 9GV1224P4G1(11) Air Flow 9GV1248P4J1(11) Operating Voltage Range PWM 1 Duty Cycle V V V Air Flow 9GV1212P4G1(11) Static Pressure PWM PWM 1 Duty Cycle V 24V 2.4V Air Flow GV1224P4G1(11) Static Pressure PWM 1 Duty Cycle V 48V 4.8V Air Flow 9GV1248P4J1(11) PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 6, 5, 5,1min -1 4, 3, 2, 1,65min -1 1, 1 PWM PWM % Duty Cycle % 9GV1212P4G1(11) Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz 6, 5, 4, 3, 2, 1,65min -1 1, 5,1min -1 1 PWM PWM % Duty Cycle % 9GV1224P4G1(11) Rotation min Speed min , 5, 4, 3, Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 5,4min -1 3,min -1 2, 1, 1 PWM PWM % Duty Cycle % 9GV1248P4J1(11) 133

135 DC Fan 12mm DC 48V DC 48V % PWM Duty Cycle 1% 5% % 5% PWM Duty Cycle 1% GV1248P4G1(11) GV1248P4H1(11) PWM PWM 1 Duty Cycle 6V 48V 4.8V PWM PWM 1 Duty Cycle 6 V 48 V 4.8 V GV1248P4G1(11) GV1248P4H1(11) Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM PWM 25kHz Frequency 25kHz 6, 5, 4, 3, 2, 1,65min -1 1, 5,1min -1 Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM PWM 25kHz Frequency 25kHz 6, 5, 4, 3, 2, 1,65min -1 1, 4,6min -1 12mm 1 PWM PWM % Duty Cycle % 9GV1248P4G1(11) 1 PWM PWM % Duty Cycle % 9GV1248P4H1(11) 134

136 DC Fan 12 mm sq. San Ace 12 25mm thick (GV type), 25mm thick (G type) 38mm thick (GV type), 38mm thick (G type) 38mm thick (SG type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 24g Specifications Model No. G type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9G1212G41(411) , G1212E41(411) 1.2 to , G1212A41(411) , G1212H41(411) 12 6 to , G1212F41(411) , to G1212M41(411) , G1212B41(411) 1.2 to , G1224G41(411) , G1224E41(411) 2.4 to , G1224A41(411) , G1224H41(411) 12 to , G1224F41(411) , to G1224M41(411) , G1248G41(411) , G1248E41(411) , G1248A41(411) , to G1248H41(411) , G1248F41(411) , G1248M41(411) , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL17 (1) (5) (5) Rotating Direction Air Flow Direction 135

137 Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side mm DC Fan 12mm 117 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side Resin finger guards Model 19-1G Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI

138 DC Fan 12 mm sq. San Ace mm Mass 24g Air Flow - Static Pressure Characteristics inch H2O Pa G speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V inch H2O Pa E speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V inch H2O Pa A speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V G1212G41(411) 9G1224G41(411) 9G1248G41(411) G1212E41(411) 9G1224E41(411) 9G1248E41(411) G1212A41(411) 9G1224A41(411) 9G1248A41(411) F speed 27.6V/55.2V 24V/48V 2.4V/4.8V G1224F41(411) 9G1248F41(411) M speed 13.8V 12V 7V G1212M41(411) M speed 27.6V/55.2V 24V/48V 2.4V/4.8V G1224M41(411) 9G1248M41(411) 137

139 inch H2O Pa H speed 13.8V/27.6V 6V/12V 12V/24V inch H2O Pa H speed 55.2V 48V 4.8V mm F speed 7V 13.8V 12V DC Fan 12mm G1212H41(411) 9G1224H41(411) 9G1248H41(411) 9G1212F41(411) Static Pressure B speed 13.8V 12V 1.2V G1212B41(411) 138

140 DC Fan 12 mm sq. San Ace 12 General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 36g Specifications 25mm thick (GV type), 25mm thick (G type) 38mm thick (GV type), 38mm thick (G type) 38mm thick (SG type) GV type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , GV1212P1J1(11) to , GV1224P1J1(11) Note) , to to 7 4, 9GV1224P1H1(11) Note) , , GV1248P1J1(11) to , Note: Rated voltage 24V fans do not rotate when PWM duty cycle is %. PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction 139

141 Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side mm DC Fan 12mm Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-1G Outlet side Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI

142 DC Fan 12 mm sq. San Ace mm Mass 36g Air Flow - Static Pressure Characteristics PWM Duty Cycle % 5% DC 12V PWM Duty Cycle 1% Air Flow DC 24V PWM Duty Cycle 1% 5% DC 24V PWM Duty Cycle 1% 9GV1212P1J1(11) 9GV1224P1J1(11) 9GV1224P1H1(11) 5% 6 Operating Voltage Range PWM PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle 1 PWM PWM 1 Duty Cycle V 12 V 1.2 V V 24V 2.4V V 24V 2.4V GV1212P1J1(11) 9GV1224P1J1(11) 9GV1224P1H1(11) 6 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 7, 6, 5, 4, 3, 2, 1, 1,5min -1 6,4min PWM PWM % Duty Cycle % PWM PWM % Duty Cycle % PWM PWM % Duty Cycle % 9GV1212P1J1(11) Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM 25kHz Frequency 25kHz 7 6,4min GV1224P1J1(11) Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz GV1224P1H1(11) 5,2min

143 DC Fan 12mm Static Pressure % 1 2 5% 3 DC 48V PWM Duty Cycle 1% Air Flow 9GV1248P1J1(11) 8 Static Pressure PWM PWM 1 Duty Cycle V 48V 4.8V Air Flow 9GV1248P1J1(11) 7 8 Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 7, 6,4min -1 6, 5, 4, 3, 2, 1,5min -1 1, 1 PWM PWM % Duty Cycle % 9GV1248P1J1(11) 12mm 142

144 DC Fan 12 mm sq. San Ace 12 25mm thick (GV type), 25mm thick (G type) 38mm thick (GV type), 38mm thick (G type) 38mm thick (SG type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 33g Specifications Model No. G type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9G1212G11(111) , to G1212E11(111) , G1212H11(111) , G1212F11(111) 7 to , G1212M11(111) , G1224G11(111) , to G1224E11(111) , G1224H11(111) , G1224F11(111) 14 to , G1224M11(111) , G1248G11(111) , G1248E11(111) , G1248H11(111) to , G1248F11(111) , G1248M11(111) , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole (1) +3 3 Lead Wire AWG24 UL (5) 38.5 (5) Rotating Direction Air Flow Direction 143

145 Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side mm DC Fan 12mm 117 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side Resin finger guards Model 19-1G Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI

146 DC Fan 12 mm sq. San Ace mm Mass 33g Air Flow - Static Pressure Characteristics inch H2O Pa G speed E speed H speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4/4.8V inch H2O Pa V/27.6V/55.2V 2 12V/24V/48V 1.2V/2.4V/4.8V Air Flow inch H2O Pa V/27.6V 12V/24V 7V/14V G1212G11(111) 9G1224G11(111) 9G1248G11(111) 9G1212E11(111) 9G1224E11(111) 9G1248E11(111) 9G1212H11(111) 9G1224H11(111) inch H2O Pa M speed 13.8V/27.6V 12V/24V 7V/14V inch H2O Pa M speed 55.2V 48V 4.8V Air Flow Air Flow 9G1212M11(111) 9G1224M11(111) 9G1248M11(111) 145

147 inch H2O Pa H speed F speed F speed 55.2V 48V 4.8V inch H2O Pa mm 13.8V/27.6V 12V/24V 7V/14V inch H2O Pa V 48V 4.8V DC Fan 12mm Air Flow 9G1248H11(111) Air Flow 9G1212F11(111) 9G1224F11(111) Air Flow 9G1248F11(111) 146

148 DC Fan 12 mm sq. San Ace 12 25mm thick (GV type), 25mm thick (G type) 38mm thick (GV type), 38mm thick (G type) 38mm thick (SG type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 4g Specifications SG type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9SG1212G to , SG1224G , to SG1224H , SG1248G to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL17 or AWG22 UL (1) (3.5) (3.5) 38.5 Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

149 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-1G Outlet side DC Fan 12mm Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI inch H2O Pa V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V mm Air Flow - Static Pressure Characteristics G speed SG1212G11 9SG1224G11 9SG1248G11 Static Pressure H speed 27.6V 24V 2.4V SG1224H11 148

150 DC Fan 127mm sq. San Ace mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 35g Specifications Model No. To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P1312S11(111) , to P1312H11(111) , P1324S11(111) , to P1324H11(111) , P1348S11(111) , to P1348H11(111) , to 6 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole (1) Lead Wire AWG24 UL (6) (6) 38.5 Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

151 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model Surface treatment Nickel-chrome plating silver mm Outlet side 119 ( 6) DC Fan 127mm Air Flow - Static Pressure Characteristics.6 15 S speed.5 12 H speed V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V P1312S11 (111) 19P1324S11 (111) 19P1348S11 (111) P1312H11 (111) 19P1324H11 (111) 19P1348H11 (111) 15

152 DC Fan 127mm sq. San Ace mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 4g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19E1312A , to to 7 6, 19E1312S , E1324G , to 6 4, 19E1324A to , to 7 6, 19E1324S , E1348G , to 6 4, 19E1348A to , to 7 6, 19E1348S , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole (1) Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

153 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model Surface treatment Nickel-chrome plating silver Outlet side 119 ( 6) DC Fan 127mm Air Flow - Static Pressure Characteristics G speed 27.6V/55.2V 24V/48V mm 2.4V/4.8V E1324G11 19E1348G11 A speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V Air Flow 19E1312A11 19E1324A11 19E1348A S speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V Air Flow 19E1312S11 19E1324S11 19E1348S11 152

154 DC Fan 14 mm sq. San Ace 14 38mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 45g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19P1412H , to P1412M , P1424H , to P1424M , P1448H , to P1448M , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole (1) Lead Wire AWG24 UL (5) (5) Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

155 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model H Surface treatment Cation electropainting black DC Fan 14mm mm Air Flow - Static Pressure Characteristics H speed M speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V P1412H11 19P1424H11 19P1448H P1412M11 19P1424M11 19P1448M11 154

156 DC Fan 15 mm sq. San Ace 15 5mm thick (GV type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 45g Specifications Model No. GV type To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9GV1512H51(511) , to GV1512M51(511) , GV1524M51(511) to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole (1) Lead Wire AWG22 UL (6.5) 5.5 (6.5) Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

157 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model Surface treatment Nickel-chrome plating silver Outlet side ( 62.2) inch H2O Pa V 25 12V 2 1.2V mm DC Fan 15mm Air Flow - Static Pressure Characteristics H speed M speed M speed V V 1.2V Air Flow 9GV1512H51(511) 9GV1512M51(511) 9GV1524M51(511) Static Pressure V V V

158 DC Fan 172 mm San Ace mm thick(sidecut type), 51mm thick(sidecut type SG type) 51mm thick(sidecut type GV type) 51mm thick(sidecut type), 51mm thick(round type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 172mm 147mm 25mm Mass 5g Specifications SideCut type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19E4712M , to E4712L , E4724H , E4724F , to E4724M , E4724L , E4748S , E4748H , E4748F to , E4748M , E4748L , to 6 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole (1) Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm R

159 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side For the finger guard Model: E, H, 19-32, fix the finger guard to two holes as shown in the diagram. Do not fix it to any other holes Finger guards Plain washers Spring washers Screws Hexagonal nuts DC Fan 172mm Fan Air Flow - Static Pressure Characteristics inch H2O Pa S speed 55.2V 48V 4.8V E4748S41 inch H2O Pa H speed V/55.2V 24V/48V 1 2.4V/4.8V E4724H41 19E4748H41 inch H2O Pa F speed 27.6V/55.2V 24V/48V 2.4V/4.8V E4724F41 19E4748F M speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V E4712M41 19E4724M41 19E4748M41 inch H2O Pa L speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V Air Flow 19E4712L41 19E4724L41 19E4748L41 172mm 158

160 DC Fan 172 mm San Ace mm thick(sidecut type), 51mm thick(sidecut type SG type) 51mm thick(sidecut type GV type) 51mm thick(sidecut type), 51mm thick(round type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 172mm 15mm 51mm Mass 76g Specifications SideCut type SG type Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , SG5724P5H to to , , , SG5748P5G1 4, , to 72 1 to , SG5748P5H , PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm Mounting Hole Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction Lead Wire AWG22 UL Air Flow Direction R Options Unit : mm Finger guards Model J Surface treatment Nickel-chrome plating silver For the finger guard Model: J, fix the finger guard to four holes as shown in the diagram. 162 Finger guards Hexagonal nuts Plain washers Spring washers 152 Screws Fan 159

161 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side For the finger guard Model: E, H, 19-32, fix the finger guard to two holes as shown in the diagram. Do not fix it to any other holes. Hexagonal nuts Finger guards Plain washers Spring washers Screws DC Fan 172mm Fan Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 24V PWM Duty Cycle 1% 5% % Air Flow 9SG5724P5H61 Static Pressure 5. 1,2 4. 1, DC 48V PWM Duty Cycle 1% 5% % SG5748P5G1 Static Pressure DC 48V 7 6 PWM Duty Cycle 1% % 2 1 % Air Flow 9SG5748P5H1 Operating Voltage Range PWM PWM 1 Duty Cycle 27.6V 24V 2.4V SG5724P5H61 inch H2O Pa Static Pressure ,2 1, PWM PWM 1 Duty Cycle 72V 48V 36V SG5748P5G1 Static Pressure PWM PWM 1 Duty Cycle 1 48V/72V 36V Air Flow 9SG5748P5H1 172mm PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz 7, 6,5min -1 6, 5, 4, 3, 2, 1, 1,3min PWM PWM % Duty Cycle % 9SG5724P5H61 Rotation min Speed min , 8, 7, 6, 5, 4, 3, 2, Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 8,6min -1 2,min -1 1, 1 PWM PWM % Duty Cycle % 9SG5748P5G1 Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM PWM 25kHz Frequency 25kHz 9, 8, 7, 6,5min -1 6, 5, 4, 3, 2, 2,min -1 1, 1 PWM PWM % Duty Cycle % 9SG5748P5H1 16

162 DC Fan 172 mm San Ace mm thick(sidecut type), 51mm thick(sidecut type SG type) 51mm thick(sidecut type GV type) 51mm thick(sidecut type), 51mm thick(round type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing 172mm 15mm 51mm Mass 8g Specifications SideCut type GV type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9GV5724H to GV5748H to , , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG22 UL Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm R

163 Options Unit : mm Finger guards Model J Surface treatment Nickel-chrome plating silver For the finger guard Model: J, fix the finger guard to four holes as shown in the diagram. 162 Finger guards Hexagonal nuts Plain washers Spring washers Screws DC Fan 172mm Fan Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side For the finger guard Model: E, H, 19-32, fix the finger guard to two holes as shown in the diagram. Do not fix it to any other holes. 162 Hexagonal nuts Finger guards Plain washers Spring washers 152 Screws Fan Air Flow - Static Pressure Characteristics H speed 27.6V/55.2V 24V/48V 2.4V/4.8V 172mm Air Flow 9GV5724H51 9GV5748H51 162

164 DC Fan 172 mm San Ace mm thick(sidecut type), 51mm thick(sidecut type SG type) 51mm thick(sidecut type GV type) 51mm thick(sidecut type), 51mm thick(round type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 172mm 15mm 51mm Mass 76g Specifications SideCut type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19E5712K , E5712Y , to 6 19E5712H to , E5712F , to 7 19E5712M , E5724C , E5724K , E5724H to , E5724F , to 7 19E5724M , E5748C , E5748K , to 6 19E5748H to , E5748F , to 7 19E5748M , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole 1 Reference dimension of mounting holes and vent opening Unit : mm Lead Wire AWG24 UL17 or AWG22 UL R4.25 Rotating Direction Air Flow Direction

165 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side DC Fan 172mm Air Flow - Static Pressure Characteristics inch H2O Pa K speed Y speed H speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V inch H2O Pa V 12V 1.2V V/27.6V/55.2V V/24V/48V 1.2V/2.4V/4.8V E5712K51 19E5724K51 19E5748K E5712Y E5712H51 19E5724H51 19E5748H51 Static Pressure F speed 13.8 V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V E5712F51 19E5724F51 19E5748F inch H2O Pa M speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V Air Flow 19E5712M51 19E5724M51 19E5748M51 inch H2O Pa C speed 27.6V/55.2V 24V/48V 2.4V/4.8V Air Flow 19E5724C51 19E5748C51 172mm 164

166 DC Fan 172 mm San Ace mm thick(sidecut type), 51mm thick(sidecut type SG type) 51mm thick(sidecut type GV type) 51mm thick(sidecut type), 51mm thick(round type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 172mm 51mm Mass 78g Specifications Round type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19E1712K , to 6 19E1712H , to E1712F , E1712M , E1724C , to 7 19E1724K , to E1724H , E1724M , E1748C , E1748K , to to E1748H , to 7 19E1748M , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole (1) Lead Wire AWG24 UL17 or AWG22 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm R

167 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model Surface treatment Nickel-chrome plating silver Outlet side DC Fan 172mm Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side Air Flow - Static Pressure Characteristics inch H2O Pa C speed inch H2O Pa K speed inch H2O Pa.8 2 H speed V/55.2V 24V/48V 2.4V/4.8V V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V E1724C51 19E1748C E1712K51 19E1724K51 19E1748K E1712H51 19E1724H51 19E1748H51 172mm inch H2O Pa M speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V E1712M51 19E1724M51 19E1748M51 Static Pressure F speed V 12V 1 1.2V E1712F51 166

168 DC Fan 2mm San Ace 2 7mm thick (Round type) 7mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing Power on when current is shut off. Do not power on 1sec or more after power off. 2mm 7mm Mass 18g Specifications Model No. The MH speed and AS speed are two speeds. Round type Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19E224S to , E224H1 2.4 to , E224AS to , , E224MH1 2.4 to , , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole (1) Lead Wire AWG22 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm R2 4-R

169 Options Unit : mm Finger guards Model H Surface treatment Nickel-chrome plating silver Cation electropainting black Model H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side DC Fan 2mm Signal connection type VS VS VC VC Control Brushless DC fan VC VC Control Brushless DC fan IC 2mA MAX. IC 2mA MAX. Air Flow - Static Pressure Characteristics H speed S speed MH Two-speed inch H2O Pa V 24V 2.4V Air Flow 19E224H V 25 24V V Air Flow 19E224S V High rotation 24V Low rotation E224MH1 2mm inch H2O Pa AS Two-speed 24V High rotation 24V Low rotation E224AS1 168

170 DC Fan 2mm San Ace 2 7mm thick (Round type) 7mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing Power on when current is shut off. Do not power on 1sec or more after power off. 2mm 7mm Mass 18g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9EC224H to , EC248A1 43. to , EC248H1 4.8 to , to 6 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting hole flat head screw Mounting Hole (1) Lead Wire AWG22 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm R2 4-R

171 Options Unit : mm Finger guards Model H Surface treatment Nickel-chrome plating silver Cation electropainting black Model H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side mm DC Fan 2mm Air Flow - Static Pressure Characteristics inch H2O Pa A speed 51V 48V 43V EC248A1 inch H2O Pa H speed 26.4V/52.8V 24V/48V 2.4V/4.8V EC224H1 9EC248H1 17

172 Counter Rotating Fan 38mm sq. San Ace 38 48mm thick (CRA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing mm Mass 8g CRA type Specifications Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet ,6 14, CRA312P4K ,28 4, to to 7 4, , 13, CRA312P4J ,8 3, PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Inlet side Mounting Hole Outlet side Mounting Hole Lead Wire AWG28 UL17 Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm 37 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver

173 Air Flow - Static Pressure Characteristics PWM Duty Cycle 38mm % DC 12V PWM Duty Cycle 1% 5% CRA312P4K3 Operating Voltage Range PWM PWM 1 Duty Cycle 13.2V 12V 1.8V CRA312P4K % 5% DC 12V PWM Duty Cycle 1% CRA312P4J PWM PWM 1 Duty Cycle 13.2V 12V 1.8V CRA312P4J Counter Rotating Fan 38mm PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12VDC PWM 25kHz Frequency 25kHz 2, 15, 1, 5, 5,28min -1 4,2min -1 Inlet Outlet 17,6min -1 14,52min -1 1 PWM PWM % Duty Cycle % 9CRA312P4K3 Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 4,8min -1 1, 5, 3,96min -1 Inlet Outlet 16,min -1 13,2min -1 1 PWM PWM % Duty Cycle % 9CRA312P4J3 172

174 Counter Rotating Fan 4mm sq. San Ace 4 48mm thick (CRA type), 56mm thick (CRB type) 56mm thick (CRF type), 56mm thick (CRD type) 56mm thick (CRE type), 56mm thick (CRA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing mm Mass 8g Specifications CRA type Model No. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet 9CRA412P4K ,5 11, ,25 3, CRA412P4J to ,2 1, ,5 3, to 7 4, 9CRA412P4G ,7 9, ,41 2, PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Mounting Hole Inlet side Lead Wire AWG28 UL17 Outlet side Mounting Hole Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver

175 Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V PWM Duty Cycle 1% 5% % CRA412P4K3 Operating Voltage Range % DC 12V PWM Duty Cycle 1% 5% CRA412P4J DC 12V PWM Duty Cycle 1% 5% % mm CRA412P4G3 Counter Rotating Fan 4mm PWM PWM 1 Duty Cycle 13.2V 12V 1.8V PWM PWM 1 Duty Cycle 13.2V 12V 1.8V PWM PWM 1 Duty Cycle 13.2V 12V 1.8V CRA412P4K CRA412P4J CRA412P4G3 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12VDC PWM 25kHz Frequency 25kHz 2, 15, Inlet 17,5min -1 5,25min -1 11,7min -1 1, Outlet 5, 3,51min -1 1 PWM PWM % Duty Cycle % 9CRA412P4K3 Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 1, Inlet 16,2min -1 4,5min -1 1,8min -1 Outlet 5, 3,min -1 1 PWM PWM % Duty Cycle % 9CRA412P4J3 Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 1, Inlet 14,7min -1 4,41min -1 9,8min -1 Outlet 5, 2,94min -1 1 PWM PWM % Duty Cycle % 9CRA412P4G3 174

176 Counter Rotating Fan 4mm sq. San Ace 4 48mm thick (CRA type), 56mm thick (CRB type) 56mm thick (CRF type), 56mm thick (CRD type) 56mm thick (CRE type), 56mm thick (CRA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing mm Mass 1g CRB type Specifications Model No. 9CRB412P5K1 9CRB412P5J21 Without Sensor Pulse Sensor PWM Control Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet , 17, ,7 5, to to 7 4, ,3 16, ,45 3, Available upon request for all the models above. PWM Frequency 25kHz Dimensions Unit : mm Inlet side Outlet side Mounting Hole (1) 56.5 (5) (5) Mounting Hole (1) Lead Wire AWG28 UL161 Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm

177 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Air Flow - Static Pressure Characteristics PWM Duty Cycle 38.5 Counter Rotating Fan 4mm DC12V Static Pressure % PWM Duty Cycle 1% 5% Air Flow 9CRB412P5K1 Static Pressure % PWM Duty Cycle 1% 5% DC 12V Air Flow 9CRB412P5J21 Operating Voltage Range PWM PWM 1 Duty Cycle Static Pressure V 12V 1.8V Air Flow 9CRB412P5K1 Static Pressure PWM PWM 1% Duty Cycle 1 12V/13.2V 1.8V Air Flow 9CRB412P5J21 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 1, 5, Inlet 5,7min -1 5,1min -1 Outlet 1 19,min -1 17,min -1 Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 1, 5, 3,45min -1 Inlet 3,2min -1 Outlet 1 17,3min -1 16,min -1 4mm PWM PWM % Duty Cycle % 9CRB412P5K1 PWM PWM % Duty Cycle % 9CRB412P5J21 176

178 Counter Rotating Fan 4mm sq. San Ace 4 48mm thick (CRA type), 56mm thick (CRB type) 56mm thick (CRF type), 56mm thick (CRD type) 56mm thick (CRE type), 56mm thick (CRA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing mm Mass 9g Specifications CRD type Model No. 9CRD412P5J3 9CRD412P5G3 9CRD412P5H3 9CRD412P5M3 Without Sensor Pulse Sensor PWM Control Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet , 12, ,7 2, ,7 11, to ,35 2, , 1, to 7 4, , 2, , 9, , 1, Available upon request for all the models above. PWM Frequency 25kHz Dimensions Unit : mm Inlet side Outlet side Mounting Hole Mounting Hole 3 32 Lead Wire AWG28 UL Rotating Direction Air Flow Direction Rotating Direction 179

179 Reference dimension of mounting holes and vent opening Unit : mm mm Counter Rotating Fan 4mm Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver 18

180 Counter Rotating Fan 4mm sq. San Ace mm Mass 9g Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V % % PWM Duty Cycle PWM Duty Cycle PWM Duty Cycle 1% 2 5 1% 2 5 1% Static Pressure % % CRD412P5J3 9CRD412P5G3 9CRD412P5H3 Operating Voltage Range DC 12V % % 7 DC 12V PWM PWM 1 Duty Cycle V 12V 1.8V CRD412P5J3 PWM PWM 1 Duty Cycle V 12V V CRD412P5G3 PWM PWM 1 Duty Cycle V 12V V CRD412P5H3 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12VDC PWM PWM 25kHz Frequency 25kHz 2, 19,min -1 Inlet 15, 3,7min -1 1, Outlet 12,6min -1 5, 2,5min -1 1 PWM PWM % Duty Cycle % 9CRD412P5J3 Rotation min Speed min -1-1 Voltage 12V DC12VDC PWM 25kHz Frequency 25kHz 2, Inlet 15, 3,35min -1 1, Outlet 16,7min -1 11,25min -1 5, 2,25min -1 1 PWM PWM % Duty Cycle % 9CRD412P5G3 Rotation min Speed min -1-1 Voltage 12V DC12VDC PWM PWM 25kHz Frequency 25kHz 2, 15, Inlet 15,min -1 1, 3,min -1 1,min -1 Outlet 5, 2,min -1 1 PWM PWM % Duty Cycle % 9CRD412P5H3 181

181 PWM Duty Cycle 1% 5% % DC 12V CRD412P5M3 4mm Counter Rotating Fan 4mm PWM PWM 1 Duty Cycle V V V CRD412P5M3 Rotation min Speed min -1-1 Voltage 12V DC12VDC PWM PWM 25kHz Frequency 25kHz 2, 15, Inlet 1, 2,min -1 5, Outlet 14,min -1 9,3min -1 1,3min -1 1 PWM PWM % Duty Cycle % 9CRD412P5M3 182

182 Counter Rotating Fan 4mm sq. San Ace 4 48mm thick (CRA type), 56mm thick (CRB type) 56mm thick (CRF type), 56mm thick (CRD type) 56mm thick (CRE type), 56mm thick (CRA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Aluminum, Impeller: Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing mm Mass 11g Specifications Low vibration CRE type Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet ,8 12, CRE412P5J to to 7 4, ,85 2, PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Inlet side Mounting Hole (1) Outlet side Mounting Hole (1) Lead Wire AWG28 UL Rotating Direction Airflow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver

183 Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V PWM Duty Cycle 1% 5% % CRE412P5J3 Operating Voltage Range Counter Rotating Fan 4mm 4mm PWM PWM 1 Duty Cycle 13.2V 12V 1.8V CRE412P5J3 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 2, 15, 2,85min 1, -1 5, 2,25min -1 Inlet Outlet 15,8min -1 12,2min -1 1 PWM PWM % Duty Cycle % 9CRE412P5J3 184

184 Counter Rotating Fan 4mm sq. San Ace 4 48mm thick (CRA type), 56mm thick (CRB type) 56mm thick (CRF type), 56mm thick (CRD type) 56mm thick (CRE type), 56mm thick (CRA type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Outlet orange gray Sensor purple Storage Temperature 3 to 7 Non-condensing mm Mass 9g Specifications CRA type Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet 9CRA412K to , 13, to 6 9CRA412J ,8 12, , 1.8 to to 7 9CRA412G , 1, PWM Frequency 25kHz Available upon request for all the Please inquire as the availability of these functions depend Without Sensor Pulse Sensor models above. Lock Sensor PWM Control on the model. Dimensions Unit : mm Inlet side Mounting Hole Outlet side Mounting Hole Lead Wire AWG28 UL17 Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm

185 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Air Flow - Static Pressure Characteristics V 12 V 1.8 V Air Flow 9CRA412K J speed 13.2 V 12 V 1.8 V Air Flow 9CRA412J V 5 12 V V Air Flow 9CRA412G51 4mm Counter Rotating Fan 4mm K speed G speed 186

186 Counter Rotating Fan 6mm sq. San Ace 6 51mm thick (CR type), 76mm thick (CRA type) 76mm thick (CR type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing mm Mass 18g CR type Specifications Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet ,5 9, CR612P5G , 2, to to 7 4, ,5 8, CR612P5H , 2, PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Inlet side Mounting Hole Outlet side Mounting Hole Lead Wire AWG26 UL143 Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Options Unit : mm Finger guards Model E H 53 Surface treatment Nickel-chrome plating silver Cation electropainting black

187 Options Unit : mm Resin finger guards Model 19-13G Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V PWM Duty Cycle 1% 5% % CR612P5G3 9CR612P5H DC 12V PWM Duty Cycle 1% 5% % Counter Rotating Fan 6mm Operating Voltage Range PWM PWM 1 Duty Cycle V 12V 1.8V PWM PWM 1 Duty Cycle V 12V 1.8V CR612P5G CR612P5H3 2. PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12VDC PWM 25kHz Frequency 25kHz 15, 1, 5, 3,min -1 2,3min -1 Inlet Outlet 11,5min -1 9,min -1 1 PWM PWM % Duty Cycle % Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 15, 1, 5, 3,min -1 2,3min -1 Inlet Outlet 1,5min -1 8,2min -1 1 PWM PWM % Duty Cycle % 6mm 9CR612P5G3 9CR612P5H3 188

188 Counter Rotating Fan 6mm sq. San Ace 6 51mm thick (CR type), 76mm thick (CRA type) 76mm thick (CR type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing mm Mass 27g Specifications CRA type Model No. 9CRA612PG1 9CRA612PS1 Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note) V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet ,5 13, , ,6 2, ,/ to to , 11, (7,/4 ) ,2 2, Note: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Inlet side Mounting Hole +5 3 (1) 76.5 (4) (4) Outlet side (1) Lead Wire AWG26 UL Mounting Hole Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Options Unit : mm Finger guards Model E H 53 Surface treatment Nickel-chrome plating silver Cation electropainting black

189 Options Unit : mm Resin finger guards Model 19-13G Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI Static Pressure 5.3 Air Flow - Static Pressure Characteristics PWM Duty Cycle ,2 1, % PWM Duty Cycle 1% 5% DC 12V CRA612PG1 Static Pressure ,2 1, % % DC 12V PWM Duty Cycle 1% CRA612PS Counter Rotating Fan 6mm Operating Voltage Range Static Pressure 5. 1,2 4. 1, PWM PWM 1 Duty Cycle V 12V 1.8V CRA612PG1 Static Pressure 5. 1,2 4. 1, PWM PWM 1 Duty Cycle V 12V 1.8V CRA612PS1 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 18, 16, 14, Inlet 12, 1, 3,6min -1 8, 6, Outlet 16,5min -1 13,min -1 4, 2, 2,8min -1 1 PWM PWM % Duty Cycle % 9CRA612PG1 Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 18, 16, 14, 12, 1, 8, 6, 3,2min -1 Inlet Outlet 14,min -1 11,min -1 4, 2, 2,5min -1 1 PWM PWM % Duty Cycle % 9CRA612PS1 19 6mm

190 Counter Rotating Fan 6mm sq. San Ace 6 51mm thick (CR type), 76mm thick (CRA type) 76mm thick (CR type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Outlet orange gray Sensor purple Storage Temperature 3 to 7 Non-condensing mm Mass 23g CR type Specifications Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet 9CR612S ,5 7, to to 6 4, 9CR612H ,3 6, Available upon request for all the Please inquire as the availability of these functions depend Without Sensor Pulse Sensor models above. Lock Sensor PWM Control on the model. Dimensions Unit : mm Inlet side Outlet side Mounting Hole Mounting Hole Lead Wire AWG24 UL17 UL17 AWG Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm 191

191 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-13G Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI Counter Rotating Fan 6mm mm Air Flow - Static Pressure Characteristics S speed V 12V 1.8V CR612S1 3. H speed V V V CR612H1 192

192 Counter Rotating Fan 8mm sq. San Ace 8 8mm thick (CRA type), 8mm thick (CR type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing 8 8 8mm Mass 45g CRA type Specifications Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note) Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet , 11, , CRA812P8G to , 1, ,/6 1 to , 11, , (7,/4 ) 9CRA848P8G to , 4, Note: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Mounting Hole Inlet side (4) 8 1 (4) Outlet side (1) +3 3 Lead Wire AWG24 UL Mounting Hole Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Outlet side Model 19-49E Surface treatment Nickel-chrome plating silver 19-49H Cation electropainting black

193 Options Unit : mm Resin finger guards Model 19-12G Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Air Flow - Static Pressure Characteristics PWM Duty Cycle Counter Rotating Fan 8mm Static Pressure DC 12V PWM Duty Cycle 1% 5% % Air Flow 9CRA812P8G1 (m 3 /min) (CFM) Static Pressure DC 48V PWM Duty Cycle 1% 5% % CRA848P8G1 (m 3 /min) (CFM) Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle 1 12V/13.2V 1.8V Air Flow 9CRA812P8G1 (m 3 /min) (CFM) Static Pressure PWM PWM 1 Duty Cycle 1 48V/55.2V 4.8V Air Flow 9CRA848P8G1 (m 3 /min) (CFM) PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 12, min -1 11,3 min -1 12, 11, 1, Inlet 9, 8, 7, 6, 2,min -1 Outlet 5, 4, 3, 2, 1,9min 1, 1 PWM PWM % Duty Cycle % 9CRA812P8G1 Rotation min Speed min , 11, 1, Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz Inlet 12, min -1 11,3 min -1 9, 8, 5,min -1 Outlet 7, 6, 5, 4, 4,7min -1 3, 2, 1, 1 PWM PWM % Duty Cycle % 9CRA848P8G mm

194 Counter Rotating Fan 8mm sq. San Ace 8 8mm thick (CRA type), 8mm thick (CR type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Outlet orange gray Sensor purple Storage Temperature 3 to 7 Non-condensing 8 8 8mm Mass 35g CR type Specifications Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet 9CR812S , 5, to to 6 4, 9CR812H , 4, Available upon request for all the Please inquire as the availability of these functions depend Without Sensor Pulse Sensor models above. Lock Sensor PWM Control on the model. Dimensions Unit : mm Inlet side Outlet side Mounting Hole Lead Wire AWG24 UL Mounting Hole Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm

195 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin finger guards Model 19-12G Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Counter Rotating Fan 8mm V 12V 1.8V Air Flow 9CR812S V 12V 1.8V Air Flow 9CR812H81 5 8mm Air Flow - Static Pressure Characteristics S speed H speed 196

196 Counter Rotating Fan 12 mm sq. San Ace 12 76mm thick CR type General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing mm Mass 67g Specifications CR type Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet ,2 3, CR1212PG to to 6 4, ,7 1, PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Outlet side Inlet side Mounting Hole Mounting Hole Lead Wire AWG22 UL143 Rotating Direction Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

197 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin finger guards Model 19-1G Model 19-19E 19-19K Outlet side Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI Counter Rotating Fan 12mm Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 12V PWM Duty Cycle 1% 5% % CR1212PG3 Operating Voltage Range PWM PWM 1 Duty Cycle V 12V 1.8V CR1212PG3 PWM Duty Speed Characteristics Example 12mm Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 8, Inlet 6, 6,2min -1 2,7min -1 4, 3,8min -1 Outlet 2, 1,8min -1 1 PWM PWM % Duty Cycle % 9CR1212PG3 198

198 Counter Rotating Fan 172 mm San Ace mm thick (CR type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Aluminum, Impeller: Plastics (Flammability: UL94V-) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire Inlet red black Sensor yellow Control brown Outlet orange gray Sensor purple Control white Storage Temperature 3 to 7 Non-condensing 172mm 15mm 12mm Mass 1,6g Specifications CR type Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h Inlet Outlet ,3 6, , CR5748P9G to 72 1 to 7 4, ,4 1, Without Sensor Pulse Sensor Lock Sensor Low speed Sensor PWM Control Available upon request for all the models above. PWM Frequency 25kHz Dimensions Unit : mm Outlet side Mounting Hole +3 3 (1) Inlet side Mounting Hole (1) +3 3 Lead Wire AWG22 UL Rotating Direction Airflow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Options Unit : mm Finger guards Model J Surface treatment Nickel-chrome plating silver For the finger guard Model: J, fix the finger guard to four holes as shown in the diagram. Finger guards Plain washers Spring washers Screws Hexagonal nuts Fan

199 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side For the finger guard Model: E, H, 19-32, fix the finger guard to two holes as shown in the diagram. Do not fix it to any other holes. Hexagonal nuts Air Flow - Static Pressure Characteristics Finger guards Plain washers Spring washers Screws Fan Counter Rotating Fan 172mm PWM Duty Cycle Static Pressure 1,6 6 1,4 5 1,2 4 1, % PWM Duty Cycle 1% 5% DC 48V Air Flow 9CR5748P9G1 Operating Voltage Range Static Pressure 1,6 6 1,4 5 1,2 4 1, PWM PWM 1 Duty Cycle 1 72V 48V 36V CR5748P9G1 172mm PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 8, 7, Inlet 6, 5, 4, 3, 2, 1, 2,4min -1 1,9min -1 Outlet 7,3min -1 6,4min -1 1 PWM PWM % Duty Cycle % 9CR5748P9G1 2

200 Splash Proof Fan 6mm sq. San Ace 6W 25mm thick(wp type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model Indoor, L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 11g Specifications Model No. Dust resistant device with IP 55 protection against water jets WPtype To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WP612G41(411) 1.2 to , to 6 4, 12 9WP612H41(411) 1.2 to , WP624H41(411) to , to 7 6, 9WP648H41(411) 48 4 to , Available upon request for all the Without Sensor Pulse Sensor models above. Lock Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

201 Options Unit : mm Finger guards Model H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin Finger guards Model 19-13G Air Flow - Static Pressure Characteristics G speed 13.2V 12V V WP612G41(411) H speed 13.8V/27.6V 12V/24V 1.2V/2.4V WP612H41(411) 9WP624H41(411) H speed 53V 48V 4V WP648H41(411) 6mm Splash Proof Fan 6mm 22

202 Splash Proof Fan 8mm sq. San Ace 8W 25mm thick(wp type), 25mm thick(ws type) 38mm thick(wv type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 13g Specifications Model No. Dust resistant device with IP 55 protection against water jets WPtype To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WP812G41(411) 1.8 to , to 6 4, 12 9WP812H41(411) 1.2 to , , 9WP824H41(411) to , to 7 9WP848S41(411) to , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Rotating Direction Lead Wire AWG24 UL17 Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

203 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin Finger guards Model 19-12G Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black Splash Proof Fan 8mm 8mm Air Flow - Static Pressure Characteristics G speed 13.2V 12V 1.8V WP812G41(411) H speed 13.8V/27.6V 12V/24V 1.2V/2.4V WP812H41(411) 9WP824H41(411) S speed 55.2V 48V 4.8V WP848S41(411) 24

204 Splash Proof Fan 8mm sq. San Ace 8W 25mm thick(wp type), 25mm thick(ws type) 38mm thick(wv type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 12g Specifications Model No. Dust resistant device with IP 54 protection against water spray WStype To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WS812H41(411) , WS812F41(411) to , WS812M41(411) , WS824H41(411) , WS824F41(411) to , WS824M41(411) , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole With ribs Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

205 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin Finger guards Model 19-12G Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black mm Splash Proof Fan 8mm 11.2 Air Flow - Static Pressure Characteristics H speed F speed M speed 13.8V/27.6V 12V/24V 1.2V/2.4V V/27.6V 12V/24V 1.2V/2.4V V/27.6V 12V/24V 1.2V/2.4V WS812H41(411) 9WS824H41(411) WS812F41(411) 9WS824F41(411) WS812M41(411) 9WS824M41(411) 26

206 Splash Proof Fan 8mm 36mm sq. San Ace 8W 25mm thick(wp type), 25mm thick(ws type) 38mm thick(wv type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-1) Expected Life Varies for each model (Indoor, L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 235g Specifications Dust resistant device with IP 55 protection against water jets WVtype To order a ribless type, replace the last digits of a model number with digits in parenthesis. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note) Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , ,/6 9WV848P1H1(11) to to , (7,/4 ) Note: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Mounting Hole With ribs Lead Wire AWG24 UL (1) Rotating Direction (4) (4) 38.5 Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

207 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin Finger guards Model 19-12G Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black Splash Proof Fan 8mm 11.2 Air Flow - Static Pressure Characteristics PWM Duty Cycle Operating Voltage Range 2. 5 DC 48V 2. 5 PWM PWM 1 Duty Cycle Static Pressure PWM Duty Cycle 1% 5% % Static Pressure V 48V 4.8V Air Flow (m 3 /min) (CFM) 9WV848P1H1(11) Air Flow (m 3 /min) (CFM) 9WV848P1H1(11) PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 11, 1, 9,7min -1 9, 8, 7, 6, 5, 4, 4,5min -1 3, 2, 1, 1 PWM PWM % Duty Cycle % 9WV848P1H1(11) 8mm 28

208 Splash Proof Fan 92mm sq. San Ace 92W 25mm thick(ws type), 25mm thick(wp type) 38mm thick(wv type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 15g Specifications Dust resistant device with IP 54 protection against water spray WStype Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WS912H , WS912F , to WS912M , WS912L , WS924H , WS924F , to WS924M , WS924L , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

209 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin Finger guards Model 19-11G Outlet side Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Splash Proof Fan 92mm Air Flow - Static Pressure Characteristics H speed 13.8V/27.6V 12V/24V 1.2V/2.4V WS912H41 9WS924H F speed 13.8V/27.6V 12V/24V 1.2V/2.4V WS912F41 9WS924F M speed 13.8V/27.6V 12V/24V 1.2V/2.4V WS912M41 9WS924M L speed 13.8V/27.6V 12V/24V 1.2V/2.4V 92mm WS912L41 9WS924L41 21

210 Splash Proof Fan 92mm sq. San Ace 92W 25mm thick(ws type), 25mm thick(wp type) 38mm thick(wv type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 12g Specifications Dust resistant device with IP 55 protection against water jets WPtype Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WP912F to , WP924S , WP924H , to WP924F , WP924B , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

211 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin Finger guards Model 19-11G Outlet side Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Splash Proof Fan 92mm Air Flow - Static Pressure Characteristics F speed S speed H speed 6V 13.8V 12V WP912F V V V WP924S V 27.6V 1. 24V WP924H41 B speed V V V WP924B F speed V 24V 12V WP924F41 92mm 212

212 Splash Proof Fan 92mm 36mm sq. San Ace 92W 25mm thick(ws type), 25mm thick(wp type) 38mm thick(wv type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-1) Expected Life Varies for each model (Indoor, L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing mm Mass 265g Specifications Dust resistant device with IP 55 protection against water jets WVtype Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , WV948P1H to to 7 3, , Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. PWM Frequency 25kHz Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL (1) (4) (4) Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

213 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin Finger guards Model 19-11G Outlet side Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Splash Proof Fan 92mm Air Flow - Static Pressure Characteristics PWM Duty Cycle Operating Voltage Range Static Pressure DC 48V PWM Duty Cycle 1% % % WV948P1H1 (m 3 /min) (CFM) Static Pressure PWM PWM 1 Duty Cycle V V V WV948P1H1 (m 3 /min) (CFM) PWM Duty - Speed Characteristics Example Rotation min Speed min , 8, 7, 6, 5, 4, 3, 2, Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 4,min -1 8,5min -1 1, 1 PWM PWM % Duty Cycle % 9WV948P1H1 92mm 214

214 Splash Proof Fan 12 mm sq. San Ace 92W mm Mass 44g 38mm thick(wv type), 38mm thick(wp type) 38mm thick(wg type), 38mm thick(ws type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Aluminum,Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model (Indoor, L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing Specifications Dust resistant device with IP 55 protection against water jets WVtype Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h 9WV1224P1H1 Note) to , , to 7 6, 9WV1248P1J to , Note: Rated voltage 12V fans do not rotate when PWM duty cycle is %. PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Options Unit : mm Mounting Hole Lead Wire AWG24 UL (25) Finger guards Model 19-19C 19-19H 42.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black

215 Options Unit : mm Resin Finger guards Model 19-1G Air Flow - Static Pressure Characteristics PWM Duty Cycle DC24V PWM Duty Cycle 1% 5% WV1224P1H1 inch H2O Pa Static Pressure % 2 3 DC 48V PWM Duty Cycle 1% 5% WV1248P1J1 8 (m 3 /min) (CFM) Splash Proof Fan 12mm Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle 27.6 V 24 V 2.4 V WV1224P1H1 6 Static Pressure PWM PWM 1 Duty Cycle V 48V 4.8V WV1248P1J1 7 8 (m 3 /min) (CFM) PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM 25kHz Frequency 25kHz 7, 6, 5,2 min -1 5, 4, 3, 2, 1, 1 PWM PWM % Duty Cycle % Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 7, 6,4min -1 6, 5, 4, 3, 2, 1,5min 1, -1 1 PWM PWM % Duty Cycle % 9WV1224P1H1 9WV1248P1J1 12mm 216

216 Splash Proof Fan 12 mm sq. San Ace 12W 38mm thick(wv type), 38mm thick(wp type) 38mm thick(wg type), 38mm thick(ws type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 36g Specifications Dust resistant device with IP 55 protection against water jets To order a ribless type, replace the last digits of a model number with digits in parenthesis. WPtype Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WP1212H11(111) to , WP1224H11(111) to , WP1248H11(111) to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

217 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin Finger guards Model 19-1G Outlet side Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black mm Splash Proof Fan 12mm 148 Air Flow - Static Pressure Characteristics H speed 13.8V/27.6V 12V/24V 7V/14V WP1212H11(111) 9WP1224H11(111) H speed 55.2V 48V 4.8V WP1248H11(111) 218

218 Splash Proof Fan 12 mm sq. San Ace 12W 38mm thick(wv type), 38mm thick(wp type) 38mm thick(wg type), 38mm thick(ws type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum,Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 41g Specifications Dust resistant device with IP 55 protection against water jets WGtype Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WG1212G11-E , to WG1212E11-E , WG1212H11-E , WG1212F11-E 7 to , WG1212M11-E , WG1224G11-E , to WG1224E11-E , WG1224H11-E , WG1224F11-E 14 to , WG1224M11-E , WG1248G11-E , WG1248E11-E , WG1248H11-E to , WG1248F11-E , WG1248M11-E , to 7 8, 1, 8, 1, 8, 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole (25) +3 3 Lead Wire AWG24 UL17 (1) Options Unit : mm Finger guards Model 19-19C 19-19H 42.2 Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black

219 Options Unit : mm Resin Finger guards Model 19-1G Air Flow - Static Pressure Characteristics G speed E speed H speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V WG1212G11-E 9WG1224G11-E 9WG1248G11-E V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V WG1212E11-E 9WG1224E11-E 9WG1248E11-E V/27.6V 12V/24V 7V/14V WG1212H11-E 9WG1224H11-E Splash Proof Fan 12mm H speed Fspeed F speed 55.2V 48V 4.8V WG1248H11-E V/27.6V 12V/24V 7V/14V WG1212F11-E 9WG1224F11-E V 48V 4.8V WG1248F11-E M speed 13.8V/27.6V 12V/24V 7V/14V M speed 55.2V 48V 4.8V 12mm WG1212M11-E 9WG1224M11-E WG1248M11-E 22

220 Splash Proof Fan 12 mm sq. San Ace 12W 38mm thick(wv type), 38mm thick(wp type) 38mm thick(wg type), 38mm thick(ws type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 26g Specifications Dust resistant device with IP 54 protection against water spray To order a ribless type, replace the last digits of a model number with digits in parenthesis. WStype Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WS1212H11(111) 6 to , to WS1212M11(111) 6 to , to 7 9WS1224H11(111) 12 to , to WS1224M11(111) 12 to , to 7 9WS1248H11(111) 4.8 to , to WS1248M11(111) 4.8 to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm With ribs Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

221 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin Finger guards Model 19-1G Outlet side Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Splash Proof Fan 12mm 148 Air Flow - Static Pressure Characteristics H speed 13.2V/26.4V 12V/24V 6V/12V WS1212H11(111) 9WS1224H11(111) M speed 13.8V/27.6V 12V/24V 6V/12V WS1212M11(111) 9WS1224M11(111) H speed V 48V 4.8V WS1248H11(111) M speed 55.2V 48V 4.8V 12mm WS1248M11(111) 222

222 Splash Proof Fan 14 mm sq. San Ace 14W 38mm thick, 51mm thick(wb type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 65g Specifications Dust resistant device with IP 55 protection against water jets Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19W1412H11-U , to W1412M11-U , W1424H11-U , to W1424M11-U , W1448H11-U , to W1448M11-U , to 7 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

223 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model H Surface treatment Cation electropainting black mm Air Flow - Static Pressure Characteristics H speed V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V W1412H11-U 19W1424H11-U 19W1448H11-U M speed V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V W1412M11-U 19W1424M11-U 19W1448M11-U Splash Proof Fan 14mm 224

224 Splash Proof Fan 14 mm sq. San Ace 14W 38mm thick, 51mm thick(wb type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 7g Specifications Dust resistant device with IP 55 protection against water jets WBtype Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WB1412S , , 9WB1412H to , WB1412M , , 9WB1424H , to to WB1424M , WB1448S , , to WB1448H , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL17 or AWG22 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

225 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model H Surface treatment Cation electropainting black Air Flow - Static Pressure Characteristics S speed H speed M speed Splash Proof Fan 14mm 14mm V/55.2V 12V/48V 1.2V/4.8V V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V V/27.6V 12V/24V 1.2V/2.4V WB1412S51 9WB1448S WB1412H51 9WB1424H51 9WB1448H WB1412M51 9WB1424M51 226

226 Splash Proof Fan 172 mm San Ace 172W 51mm thick(sidecut type WG type), 51mm thick(sidecut type WE type) 51mm thick(round type WE type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model (Indoor,L1: Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 172mm 15mm 51mm Mass 86g Specifications SideCut type Dust resistant device with IP 55 protection against water jets WGtype Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note) Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , WG5748P5G , ,/ to to , (7,/4 ) 9WG5748P5H , Note: Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Without Sensor Pulse Sensor PWM Control Available upon request for all the models above. Dimensions Unit : mm Mounting Hole Lead Wire AWG22 UL Reference dimension of mounting holes and vent opening Unit : mm R Rotating Direction Air Flow Direction Options Unit : mm Finger guards Model J Surface treatment Nickel-chrome plating silver For the finger guard Model: J, fix the finger guard to four holes as shown in the diagram. 162 Finger guards Hexagonal nuts Plain washers Spring washers 152 Screws Fan 227

227 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side For the finger guard Model: E, H, 19-32, fix the finger guard to two holes as shown in the diagram. Do not fix it to any other holes. Hexagonal nuts Finger guards Plain washers Spring washers 152 Air Flow - Static Pressure Characteristics PWM Duty Cycle Screws Fan Splash Proof Fan 172mm inch H2O Pa Static Pressure DC 48V PWM Duty Cycle 1% 5% % WG5748P5G1 Static Pressure % 5 1 DC 48V PWM Duty Cycle 1% 5% WG5748P5H1 Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle 55.2V 48V 4.8V WG5748P5G1 Static Pressure PWM PWM 1 Duty Cycle 1 4.8V/48V/55.2V WG5748P5H1 172mm PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 9, 8,6min -1 8, 7, 6, 5, 4, 3, 2, 2,min -1 1, 1 PWM PWM % Duty Cycle % 9WG5748P5G1 Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 9, 8, 7, 6,5min -1 6, 5, 4, 3, 2, 2,min -1 1, 1 PWM PWM % Duty Cycle % 9WG5748P5H1 228

228 Splash Proof Fan 172 mm San Ace 172W 51mm thick(sidecut type WG type), 51mm thick(sidecut type WE type), 51mm thick(round type WE type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 172mm 15mm 51mm Mass 86g Specifications SideCut type Dust resistant device with IP 55 protection against water jets WEtype Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WE5724K to , , 1 to 6 9WE5748K to , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole 1 Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction +3 3 Lead Wire AWG24 UL Air Flow Direction R Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side Air Flow - Static Pressure Characteristics K speed 27.6V/55.2V 24V/48V 2.4V/4.8V WE5724K51 9WE5748K51 229

229 Splash Proof Fan 172 mm San Ace 172W 51mm thick(sidecut type WG type), 51mm thick(sidecut type WE type), 51mm thick(round type WE type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(indoor, L1:Survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 172mm 51mm Mass 89g Specifications Round type Dust resistant device with IP 55 protection against water jets WEtype Splash Proof Fan 172mm Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WE1724K to , to 6 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Dimensions Unit : mm Mounting Hole +3 3 Please inquire as the availability of these functions depend on the model. Reference dimension of mounting holes and vent opening Unit : mm (1) Lead Wire AWG24 UL Rotating Direction Air Flow Direction R Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model Surface treatment Nickel-chrome plating silver V 24V 2.4V 172mm WE1724K Outlet side Air Flow - Static Pressure Characteristics K speed Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side

230 Splash Proof Centrifugal Fan 1 mm 36mm sq. San Ace 1W 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Motor case: Aluminum (Black Painting), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (Indoor, L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 1mm 25mm Mass 16g Specifications Model No. 9W1TM48P4G1 9W1TM48P4H1 When our inlet nozzle Option Model NO. : is mounted. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h 1 Note1) , ,/ to , to 7 (7,/4 ) , Note 1: Fan does not rotate when PWM duty cycle is %. Note 2: Expected life at 4 ambient is just reference value. Max input is 9W1TM48P4G1 22W, 9W1TM48P4H1 14W at rated voltage. Dust resistant device with IP 54 protection against water spray PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm Air Flow Direction Rotating Direction 56.3 Reference dimension of mounting holes and vent opening Unit : mm Fan side 12 Inlet nozzle side Lead Wire AWG26 UL (1) Air Flow Direction M4 Options Unit : mm Inlet nozzle Model Finger guards Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Each R Inlet nozzle : Nozzle mounted in fan inlet side to adjust the flow of introduced air 231

231 Referance diagram for mounting Inlet nozzle Finger guard (1.15) Fan 5 Air Flow - Static Pressure Characteristics PWM Duty Cycle DC 48V PWM Duty Cycle 1% % DC 48V 6 PWM Duty Cycle % 5% % W1TM48P4G1 9W1TM48P4H1 The screw length 5mm is less or equal from fan edge side. 27 Splash Proof Centrifugal Fan 1mm Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle 6 V 48 V 36 V W1TM48P4G1 Static Pressure PWM PWM 1 Duty Cycle 1 6 V 48 V 36 V W1TM48P4H1 PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 8, 7, 6, 5, 4, 3, 2, 1, 7,4min -1 Rotation min Speed min -1-1 DC48V Voltage 48V DC PWM 25kHz Frequency 25kHz 8, 7, 6, 5, 4, 3, 2, 2,min -1 1, 6,4min -1 1mm 1 PWM PWM % Duty Cycle % 9W1TM48P4G1 1 PWM PWM % Duty Cycle % 9W1TM48P4H1 232

232 Splash Proof Centrifugal Fan 133 mm 36mm sq. San Ace 133W 91mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Motor case: Aluminum (Black Painting), Impeller:Plastics (Flammability: UL94V-1 MIN.) Expected Life Varies for each model (Indoor, L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 133mm 91mm Mass 72g Specifications Dust resistant device with IP 54 protection against water spray When our inletnozzle Option Model : is mounted. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 4,/6 9W1TJ48PH to , to 7 (7,/4 ) Note 1: Fan does not rotate when PWM duty cycle is %. PWM Frequency 25kHz Note 2: Expected life at 4 ambient is just reference value. Max input is 45W at rated voltage. Available upon request for all the models above. Dimensions Unit : mm Air Flow Direction Lead Wire AWG24 UL (1) M Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Fan side Inlet nozzle side

233 Options Unit : mm Inlet nozzle Model Finger guards Model Surface treatment Nickel-chrome plating silver Each R8.5 Inlet nozzle : Nozzle mounted in fan inlet side to adjust the flow of introduced air Referance diagram for mounting (2) Splash Proof Centrifugal Fan 133mm Inlet nozzle Finger guard Fan Fan (13) (12) Inlet nozzle The screw length is 6mm 6mm less or equal from fan edge side. Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure DC 48V PWM Duty Cycle 1% 5% W1TJ48PH61 Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle 48 V,6 V 3 36 V Air Flow 9W1TJ48PH61 PWM Duty Speed Characteristics Example Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 5, 4, 3, 2, 1, 4,15min PWM PWM % Duty Cycle % 9W1TJ48PH61 133mm 234

234 Splash Proof Centrifugal Fan 15 mm 36mm sq. San Ace 15W 35mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Motor case: Aluminum (Black Painting), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (Indoor, L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 15mm 35mm Mass 33g Specifications Dust resistant device with IP 54 protection against water spray When our inletnozzle Option Model : is mounted. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 4,/6 9W1TN48P1H to , to 7 (7,/4 ) Note 1: Fan does not rotate when PWM duty cycle is %. PWM Frequency 25kHz Note 2: Expected life at 4 ambient is just reference value. Max input is 22W at rated voltage. Available upon request for all the models above. Dimensions Unit : mm Air Flow Direction (1) 4-M4 Lead Wire AWG24 UL Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Fan side Inlet nozzle side

235 Options Unit : mm Inlet nozzle Model Finger guards Model Surface treatment Nickel-chrome plating silver Each Inlet side R6 Inlet nozzle : Nozzle mounted in fan inlet side to adjust the flow of introduced air Referance diagram for mounting (1) (7) Splash Proof Centrifugal Fan 15mm Fan Inlet nozzle (41) Finger guard Inlet nozzle Fan Screw length should be 4 mm or more but 4mm 6mm not exceeding 6 from fan edge face. Air Flow - Static Pressure Characteristics PWM Duty Cycle Operating Voltage Range Static Pressure DC 48V PWM Duty Cycle 1% 5% Static Pressure PWM PWM 1 Duty Cycle 55.2 V 48V 36V W1TN48P1H W1TN48P1H1 15mm PWM Duty Speed Characteristics Example Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 4, 3,8min -1 3, 2, 1, 5 1 PWM PWM % Duty Cycle % 9W1TN48P1H1 236

236 Splash Proof Centrifugal Fan 175 mm 36mm sq. San Ace 175W 69mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Motor case: Aluminum (Black Painting), Impeller:Plastics (Flammability: UL94V-1Min.) Expected Life Varies for each model (Indoor, L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 175mm 69mm Mass 76g Specifications Dust resistant device with IP 54 protection against water spray When inlet nozzle Option Model : is mounted. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 4,/6 9W1TG48PH to , to 7 (7,/4 ) Note 1: Fan does not rotate when PWM duty cycle is %. PWM Frequency 25kHz Note 2: Expected life at 4 ambient is just reference value. Max input is 6W at rated voltage. Available upon request for all the models above. Dimensions Unit : mm Air Flow Direction (1) Lead Wire AWG24 UL143 Air Flow Direction Rotating Direction M4 Reference dimension of mounting holes and vent opening Unit : mm Fan side Inlet nozzle side

237 Options Unit : mm Inlet nozzle Model Inlet nozzle Finger guard O 9 1 Each R Inlet nozzle : Nozzle mounted in fan inlet side to adjust the flow of introduced air Referance diagram for mounting (2) Finger guards Model Surface treatment Nickel-chrome plating silver Splash Proof Centrifugal Fan 175mm Fan Inlet nozzle Fan Screw length should be 4 mm 4mm 6mm or more but not exceeding 6 from fan edge face. To prevent screw from loosing, use plain washer and spring washer. Air Flow - Static Pressure Characteristics PWM Duty Cycle Operating Voltage Range Static Pressure % DC 48V PWM Duty Cycle 1% W1TG48PH61 Static Pressure PWM PWM 1 Duty Cycle 48 V,6 V 36V W1TG48PH61 175mm PWM Duty Speed Characteristics Example Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 4, 3, 3,1min -1 2, 1, 1 PWM PWM % Duty Cycle % 9W1TG48PH61 238

238 Oil Proof Fan 4mm sq. San Ace 4WF 15mm thick, 2mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-) Impeller: Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 35g Specifications Dust resistant device with IP 55 protection against water jets Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF424H to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Reference dimension of mounting holes and vent opening Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Options Unit : mm Air Flow - Static Pressure Characteristics Finger guards Model Surface treatment Nickel-chrome plating silver Static Pressure H speed 27.6V 24V 2.4V Air Flow 9WF424H71 239

239 Oil Proof Fan 4mm sq. San Ace 4WF 15mm thick, 2mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 5g Specifications Dust resistant device with IP 55 protection against water jets Oil Proof Fan 4mm Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF424H , to WF424F , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Reference dimension of mounting holes and vent opening Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Options Unit : mm Air Flow - Static Pressure Characteristics Finger guards Model Surface treatment Nickel-chrome plating silver H speed 27.6V 24V 2.4V WF424H61 Static Pressure F speed 27.6V 24V 2.4V WF424F61 4mm 24

240 Oil Proof Fan 6mm sq. San Ace 6WF 15mm thick, 2mm thick, 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 62g Specifications Dust resistant device with IP 55 protection against water jets Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF624H to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Reference dimension of mounting holes and vent opening Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Air Flow - Static Pressure Characteristics H speed 27.6V 24V 2.4V WF624H71 241

241 Oil Proof Fan 6mm sq. San Ace 6WF 15mm thick, 2mm thick, 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 8g Specifications Dust resistant device with IP 55 protection against water jets Oil Proof Fan 6mm Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF624H to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Dimensions Unit : mm Mounting Hole 5.5 Lead Wire AWG24 UL143 (4) 2.5 (4) Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction Air Flow Direction Options Unit : mm Air Flow - Static Pressure Characteristics Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Static Pressure H speed 27.6 V 24 V 12 V Air Flow 9WF624H mm 242

242 Oil Proof Fan 6mm sq. San Ace 6WF 15mm thick, 2mm thick, 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 11g Specifications Dust resistant device with IP 55 protection against water jets Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF624H to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction Air Flow Direction Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Air Flow - Static Pressure Characteristics H speed 27.6V 24V 2.4V WF624H41 243

243 Oil Proof Fan 8mm sq. San Ace 8WF 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 13g Specifications Model No. Dust resistant device with IP 55 protection against water jets Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF824S to , to 7 4, Oil Proof Fan 6mm/8mm Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction Air Flow Direction 78.5 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black Air Flow - Static Pressure Characteristics S speed 27.6 V 24 V 2.4 V 8mm Air Flow 9WF824S41 244

244 Oil Proof Fan 92mm sq. San Ace 92WF 25mm thick, 32mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 12g Specifications Dust resistant device with IP 55 protection against water jets Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF924H to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

245 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Outlet side Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black H speed 27.6V 24V 2.4V Air Flow 92mm Air Flow - Static Pressure Characteristics Static Pressure Oil Proof Fan 92mm 9WF924H41 246

246 Oil Proof Fan 92mm sq. San Ace 92WF 25mm thick, 32mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 185g Specifications Dust resistant device with IP 55 protection against water jets Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF924S , to WF924H , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Dimensions Unit : mm Mounting Hole (4) 32.5 (4) Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

247 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Outlet side Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black mm Air Flow - Static Pressure Characteristics Static Pressure S speed V V V Air Flow Static Pressure H speed V 24 V 2.4 V Oil Proof Fan 92mm 9WF924S21 9WF924H21 248

248 Oil Proof Fan 12 mm sq. San Ace 12WF 38mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing The product can be used in an oil mist environment* *Environment where machining oil mist is scattered. Usage of this product requires an evaluation with the oil that will be used mm Mass 355g Specifications Dust resistant device with IP 55 protection against water jets Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9WF1224H to , to 7 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

249 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black outlet side Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black mm Air Flow - Static Pressure Characteristics H speed 27.6V 24V 2.4V Oil Proof Fan 12mm WF1224H11 25

250 Long Life Fan 4mm sq. San Ace 4L 28mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum,Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 55g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9L412J , L412H to , L412M , to 7 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Rotating Direction Lead Wire AWG26 UL17 Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm

251 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver mm Air Flow - Static Pressure Characteristics J speed H speed M speed V 12V V V V 1.2V V 12V 1.2V Long Life Fan 4mm L412J L412H L412M31 252

252 Long Life Fan 6mm sq. San Ace 6L 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum,Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 1g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19L612G , L612S , L612H to , L612F , L612M , L624D , to 7 1, 19L624S , L624H to , L624F , L624M , L648G to , to 6 8, 48 19L648H41 4 to , to 7 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Reference dimension of mounting holes and vent opening Unit : mm Rotating Direction Air Flow Direction Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin Finger guards Model 19-13G

253 Options Unit : mm Resin filter kits Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI Air Flow - Static Pressure Characteristics G speed 13.8V 12V 1.2V G speed 19L612G41 19L648G41 19L624D V 48V 4.8V Static Pressure D speed 27.6V 24V 2.4V Long Life Fan 6mm S speed 13.8V/27.6V 12V/24V 1.2V/2.4V L612S41 19L624S H speed 13.8V/27.6V 12V/24V 1.2V/2.4V L612H41 19L624H41 H speed V V.1 2 4V L648H F speed 13.8V/27.6V 12V/24V 1.2V/2.4V M speed 13.8V/27.6V 12V/24V 1.2V/2.4V 6mm L612F41 19L624F L612M41 19L624M

254 Long Life Fan 8mm sq. San Ace 8L 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum,Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model L1:Survival rate:9% at 6, rated voltage, and continuously run in a free air state Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 15g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19L812S , L812H , L812F to , L812M , L812L , L824S , L824H , L824F to , L824M , L824L , L848H to , to 7 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

255 Options Unit : mm Finger guards Model 19-49C Surface treatment Nickel-chrome plating silver Resin Finger guards Model 19-12G Outlet side Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI Long Life Fan 8mm Air Flow - Static Pressure Characteristics S speed V/27.6V 12V/24V 1.2V/2.4V L812S41 19L824S H speed V/27.6V 12V/24V 1.2V/2.4V L812H41 19L824H F speed V/27.6V 12V/24V 1.2V/2.4V L812F41 19L824F M speed L speed H speed V/27.6V 12V/24V 1.2V/2.4V L812M41 19L824M V/27.6V 12V/24V 1.2V/2.4V L812L41 19L824L V 48V V L848H mm

256 Long Life Fan 92mm sq. San Ace 92L 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 17g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19L912S , L912H , L912F to , L912M , L912L , , 19L924H , to 7 19L924F , to L924M , L924L , L948C41 43 to , , 48 19L948H to , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

257 Options Unit : mm Finger guards Model 19-99C Surface treatment Nickel-chrome plating silver Resin Finger guards Model 19-11G Outlet side Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI Long Life Fan 92mm Air Flow - Static Pressure Characteristics S speed C speed H speed V 12V 1.2V Air Flow 19L912S V 1. 48V 43V Air Flow 19L948C V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V Air Flow 19L912H41 19L924H41 19L948H F speed M speed L speed V/27.6V 12V/24V 1.2V/2.4V Air Flow 19L912F41 19L924F V/27.6V 12V/24V 1.2V/2.4V Air Flow 19L912M41 19L924M V/27.6V 12V/24V 1.2V/2.4V Air Flow 19L912L41 19L924L mm

258 Long Life Fan 12 mm sq. San Ace 12L 38mm thick(lb type) 38mm thick(gl type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 37g Specifications LB type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9LB1212H , to , 9LB1212M , LB1224S , , 9LB1224H to , to 7 9LB1224M , , 9LB1248H , to LB1248M , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

259 Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Resin Finger guards Model 19-1G Outlet side Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI Long Life Fan 12mm Air Flow - Static Pressure Characteristics H speed M speed S speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V LB1212H11 9LB1224H11 9LB1248H LB1212M11 9LB1224M11 9LB1248M11 9LB1224S11 12mm 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V V 24V 2.4V

260 Long Life Fan 12 mm sq. San Ace 12L 38mm thick(lb type) 38mm thick(gl type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 37g Specifications GL type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9GL1212G , to GL1212E , GL1212H , GL1212F11 7 to , GL1212M , GL1224G , to GL1224E , GL1224H , GL1224F11 14 to , GL1224M , GL1248G , GL1248E , GL1248H to , GL1248F , GL1248M , to 7 8, 1, 8, 1, 8, 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor PWM Control Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction 261

261 Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side Options Unit : mm Finger guards Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side Resin Finger guards Model 19-1G Long Life Fan 12mm Model 19-19E 19-19K mm Surface treatment Nickel-chrome plating silver Cation electropainting black Resin filter kits Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI 262

262 Long Life Fan 12 mm sq. San Ace 12L mm Mass 37g Air Flow - Static Pressure Characteristics G speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V GL1212G11 9GL1224G11 9GL1248G E speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V GL1212E11 9GL1224E11 9GL1248E H speed 13.8V/27.6V 12V/24V 7V/14V GL1212H11 9GL1224H M speed 13.8V/27.6V 1 12V/24V 7V/14V GL1212M11 9GL1224M M speed 55.2V 48V 4.8V GL1248M

263 H speed F speed F speed 55.2V 9GL1248H V 48V 4.8V GL1248F11 12mm 48V 4.8V V/27.6V 12V/24V 7V/14V GL1212F11 9GL1224F11 Long Life Fan 12mm 264

264 Long Life Fan 14 mm sq. San Ace 14L 38mm thick 51mm thick(lb type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 6g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19L1412H , to L1412M , L1424H , to L1424M , L1448H , to L1448M , to 7 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

265 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model H Surface treatment Cation electropainting black Static Pressure V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V L1412H11 19L1424H11 19L1448H Static Pressure V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V L1412M11 19L1424M11 19L1448M11 14mm Air Flow - Static Pressure Characteristics H speed M speed Long Life Fan 14mm 266

266 Long Life Fan 14 mm sq. San Ace 14L 38mm thick 51mm thick(lb type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing mm Mass 61g Specifications LB type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9LB1412S , , 9LB1412H to , , 9LB1412M , LB1424S , , 9LB1424B , to LB1424H , to 7 1, 9LB1424M , LB1448S , , 9LB1448H , to LB1448F , , 9LB1448M , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL AWG22 UL143 9LB1412S51 (Model: 9LB1412S51) Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Inlet side Outlet side

267 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model H Surface treatment Cation electropainting black Air Flow - Static Pressure Characteristics S speed B speed H speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V Static Pressure V V V V/27.6V/55.2V V/24V/48V 1.2V/2.4V/4.8V Long Life Fan 14mm Air Flow Air Flow 9LB1412S51 9LB1424S51 9LB1448S51 9LB1424B51 9LB1412H51 9LB1424H51 9LB1448H F speed.4 1 M speed Static Pressure V 48V 4.8V V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V LB1448F LB1412M51 9LB1424M51 9LB1448M51 14mm 268

268 Long Life Fan 172 mm San Ace 172L 51mm thick(sidecut type) 51mm thick(round type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 172mm 15mm 51mm Mass 76g Specifications Model No. SideCut type Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19L5712H , to L5712M , L5724H , to L5724M , L5748H , to L5748M , to 7 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Low speed Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm R

269 Options Unit : mm Finger guards Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V L5712H51 19L5724H51 19L5748H51 19L5712M51 19L5724M51 19L5748M51 172mm 152 Air Flow - Static Pressure Characteristics H speed M speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V Long Life Fan 172mm 27

270 Long Life Fan 172 mm San Ace 172L 51mm thick(sidecut type) 51mm thick(round type) General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Aluminum, Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 172mm 51mm Mass 78g Specifications Round type Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19L1712H , to L1712M , L1724H , to L1724M , L1748H , to L1748M , to 7 1, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm Mounting Hole Lead Wire AWG24 UL Rotating Direction Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm R

271 Options Unit : mm Finger guards Model Surface treatment Nickel-chrome plating silver Model Surface treatment Nickel-chrome plating silver Outlet side Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side Long Life Fan 172mm Air Flow - Static Pressure Characteristics H speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V L1712H51 19L1724H51 19L1748H M speed 13.8V/27.6V/55.2V 12V/24V/48V 1.2V/2.4V/4.8V L1712M51 19L1724M51 19L1748M51 172mm 272

272 12 Centrifugal Fan 1 mm San Ace C1 25mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Motor case: Aluminum, Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 1mm 25mm Mass 15g Specifications When our inlet nozzle Option Model NO. : is mounted. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle % A W min -1 m³/min Pa inchh ² O db(a) h , TM48P4H to 6 1 to 7 4, , Note : Max input is 14 W at rated voltage. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm 56.3 Lead Wire AWG26 UL17 Air Flow Direction (1) Rotating Direction 3-M4 Air Flow Direction Reference dimension of mounting holes and vent opening Unit : mm Fan side Inlet nozzle side

273 Options Unit : mm Inlet nozzle Model Material: Steel sheet Surface treatment: Electro nickel plating Finger guards Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black Each R mm Inlet nozzle : Nozzle mounted in fan inlet side to adjust the flow of introduced air Referance diagram for mounting Inlet nozzle Finger guard Centrifugal Fan 1mm Fan 27 The screw length 5mm is less or equal from fan edge side. Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure % 5% DC 48V PWM Duty Cycle 1% TM48P4H1 Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle 6V 48V 36V Air Flow 9TM48P4H1 PWM Duty - Speed Characteristics Example Rotation min Speed min , 6, 5, 4, 3, 2, 1, Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 2,min -1 6,4min -1 1 PWM PWM % Duty Cycle % 9TM48P4H1 274

274 Centrifugal Fan 133 mm San Ace C133 91mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Motor case: Aluminum, Impeller:Plastics (Flammability: UL94V-1Min.) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 133mm 91mm Mass 66g Specifications When our inletnozzle Option Model : is mounted. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 9TJ24PH to , to 7 4, 9TJ48PH to , Note 1 Fan does not rotate when PWM duty cycle is. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm Air Flow Direction M4 Lead Wire AWG24 UL Air Flow Direction Rotating Direction Reference dimension of mounting holes and vent opening Unit : mm Fan side Inlet nozzle side

275 Options Unit : mm Inlet nozzle Model Material: Steel sheet Surface treatment: Electro nickel plating Finger guards Model Surface treatment Nickel-chrome plating silver Each R Inlet nozzle : Nozzle mounted in fan inlet side to adjust the flow of introduced air Referance diagram for mounting Centrifugal Fan 133mm Fan Finger guard Inlet nozzle The screw length 6mm is less or equal from fan edge side. Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure % DC 24/48V PWM Duty Cycle 1% TJ24PH61 9TJ48PH1 Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle V/24V/ 27.6V/48V/72V 36V TJ24PH61 9TJ48PH1 PWM Duty Speed Characteristics Example Rotation min Speed min , 4, 3, 2, 1, Voltage 24 DC24/48V / 48V DC PWM 25kHz Frequency 25kHz 4,15min -1 1 PWM PWM % Duty Cycle % 9TJ24PH61 9TJ48PH1 133mm 276

276 Centrifugal Fan 15 mm San Ace C15 35mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Motor case: Aluminum, Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 15mm 35mm Mass 33g Specifications When our inletnozzle Option Model : is mounted. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 9TN24P1H to , to 7 4, 9TN48P1H to , Note 1 : Fan does not rotate when PWM duty cycle is. Note 2 : Max input is 9TN24P1H1 21.4W 9TN48P1H1 22W. Available upon request for all the models above. PWM Frequency 25kHz Dimensions Unit : mm Reference dimension of mounting holes and vent opening Unit : mm Air Flow Direction M Lead Wire AWG24 UL143 Fan side Inlet nozzle side Air Flow Direction Rotating Direction Options Unit : mm Inlet nozzle Model Material: Steel sheet Surface treatment: Electro nickel plating 1.5 Finger guards Model Surface treatment Nickel-chrome plating silver Each Inlet side R6 Inlet nozzle : Nozzle mounted in fan inlet side to adjust the flow of introduced air

277 Referance diagram for mounting Inlet nozzle 1 Finger guard Fan 7 41 Screw length should be 4 mm or more 4mm 6mm but not exceeding 6 mm from fan edge face. Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure DC 24V PWM Duty Cycle 1% 5% Static Pressure DC 48V PWM Duty Cycle 1% 5% Centrifugal Fan 15mm TN24P1H Air Flow 9TN48P1H1 Operating Voltage Range 2. 5 PWM PWM 1 Duty Cycle 2. 5 PWM PWM 1 Duty Cycle Static Pressure V 24V 2.4V Static Pressure V 48V 36V TN24P1H TN48P1H1 5 15mm PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz 4, 3,8min -1 3, 2, 1, 5 1 PWM PWM % Duty Cycle % 9TN24P1H1 Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 4, 3,8min -1 3, 2, 1, 5 1 PWM PWM % Duty Cycle % 9TN48P1H1 278

278 Centrifugal Fan 175 mm San Ace C175 69mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Motor case: Aluminum, Impeller:Plastics (Flammability: UL94V-1Min.) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 175mm 69mm Mass 75g Specifications When inlet nozzle Option Model : is mounted. Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 9TG24PG to to 6 1 4, , 9TG48PG to to 7 Note 1 : Fan does not rotate when PWM duty cycle is. PWM Frequency 25kHz Note 2 : Max input is 13 W at rated voltage. Available upon request for all the models above. Dimensions Unit : mm Reference dimension of mounting holes and vent opening Unit : mm Air Flow Direction Lead Wire AWG22 9TG24PG1 (Model: 9TG24PG1) AWG24 9TG48PG1 (Model: 9TG48PG1) UL143 (1) Fan side Inlet nozzle side M4 Air Flow Direction Rotating Direction Options Unit : mm Inlet nozzle Model Material: Steel sheet Surface treatment: Electro nickel plating Finger guards Model Surface treatment Nickel-chrome plating silver O 9 1 Each R Inlet nozzle : Nozzle mounted in fan inlet side to adjust the flow of introduced air 279

279 Referance diagram for mounting Inlet nozzle 2 Finger guard 14 Fan Screw length should be 4 mm or more 4mm 6mm but not exceeding 6 mm from fan edge face. To prevent screw from loosing, use plain washer and spring washer. Air Flow - Static Pressure Characteristics PWM Duty Cycle Static Pressure DC 24V PWM Duty Cycle 1% 5% Air Flow 9TG24PG1 Static Pressure DC 48V PWM Duty Cycle 1% 5% Air Flow 9TG48PG1 Centrifugal Fan 175mm Operating Voltage Range Static Pressure PWM PWM 1 Duty Cycle V V V Air Flow 9TG24PG1 Static Pressure PWM PWM 1 Duty Cycle V V V Air Flow 9TG48PG1 175mm PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage 24V DC24V DC PWM 25kHz Frequency 25kHz 5, 4,7min -1 4, 3, 2, 1, 1 PWM PWM % Duty Cycle % 9TG24PG1 Rotation min Speed min -1-1 Voltage 48V DC48V DC PWM 25kHz Frequency 25kHz 5, 4,7min -1 4, 3, 2, 1, 1 PWM PWM % Duty Cycle % 9TG48PG1 28

280 Blower 76mm San Ace B76 2mm thick 3mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 76mm 3mm Mass 1g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19BD12HC , to 6 19BD12FC to , to 7 19BD12MC , BD24HC , to 6 19BD24FC to , to 7 19BD24MC , , Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm AIR FLOW Rotating Direction Lead Wire AWG24 UL Mounting Hole Air Flow Direction 285

281 Air Flow - Static Pressure Characteristics inch H2O Pa H speed 13.8V/27.6V 12V/24V 1.2V/2.4V 19BD12HC2 19BD24HC2 inch H2O Pa F speed 13.8V/27.6V 12V/24V 1.2V/2.4V Air Flow Air Flow Air Flow 76mm 19BD12FC2 19BD24FC2 inch H2O Pa M speed 13.8V/27.6V 12V/24V 1.2V/2.4V 19BD12MC2 19BD24MC2 Blower 76mm 286

282 Blower 97mm San Ace B97 33mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 97mm 33mm Mass 19g Specifications With PWM speed control function With pulse sensor Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 9BMB12P2K1 1.8 to , , BMB12P2F1 1.2 to , to 7 4, 9BMB24P2K , , to BMB24P2G , Note 1 : Fan does not rotate when PWM duty cycle is. PWM Frequency 25kHz Model No. With pulse sensor Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 9BMB12G , BMB12S , to BMB12H , BMB12F , BMB24G , BMB24S , to BMB24H , BMB24F , to 7 4, Available upon request for all the models above. Dimensions Unit : mm (With PWM speed control function With pulse sensor) 18.6 Lead Wire AWG24 UL Mounting Hole R R Rotating Direction Air Flow Direction 289

283 Air Flow - Static Pressure Characteristics PWM Duty Cycle Operating Voltage Range With PWM speed control function With pulse sensor With PWM speed control function With pulse sensor Static Pressure DC 12V PWM Duty Cycle 1% 6% 2% Air Flow Static Pressure PWM PWM 1 Duty Cycle V 12V 1.8V BMB12P2K1 PWM Duty - Speed Characteristics Example With PWM speed control function With pulse sensor Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 8, 7, 6, 5, 4, 3, 2, 1, 6,85min PWM PWM % Duty Cycle % With PWM speed control function With pulse sensor Static Pressure Static Pressure Static Pressure DC 12V PWM Duty Cycle 1% 6% 2% , % DC24V PWM Duty Cycle 1% DC 24V PWM Duty Cycle 1% 6% 2% Air Flow With PWM speed control function With pulse sensor With PWM speed control function With pulse sensor With PWM speed control function With pulse sensor Static Pressure Static Pressure Static Pressure PWM PWM 1 Duty Cycle V V V , BMB12P2F1.4.8 PWM PWM 1 Duty Cycle V V V BMB24P2G1 PWM PWM 1 Duty Cycle V 24V 21.6V BMB24P2K1 With PWM speed control function With pulse sensor With PWM speed control function With pulse sensor With PWM speed control function With pulse sensor Rotation min Speed min -1-1 Rotation min Speed min -1-1 Rotation min Speed min -1-1 Voltage 12V DC12V DC PWM 25kHz Frequency 25kHz 5, 4,5min -1 4, 3, 2, 1, 5 1 PWM PWM % Duty Cycle % With PWM speed control function With pulse sensor Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz 7, 6, 5,75min -1 5, 4, 3, 2, 1, 5 1 PWM PWM % Duty Cycle % With PWM speed control function With pulse sensor Voltage 24V DC24V DC PWM PWM 25kHz Frequency 25kHz 8, 7, 6,85min -1 6, 5, 4, 3, 2, 1, 5 1 PWM PWM % Duty Cycle % 29 Blower 97mm 97mm

284 Blower 97mm San Ace B97 97mm 33mm Mass 19g Air Flow - Static Pressure Characteristics Operating Voltage Range With pulse sensor With pulse sensor With pulse sensor V 13.8V 12V BMB12G V 13.8V 12V BMB12S V 12V 7V BMB12H With pulse sensor 13.8V 12V 7V BMB12F With pulse sensor 12V 26.4V 24V BMB24G With pulse sensor 12V 26.4V 24V BMB24S With pulse sensor With pulse sensor V 26.4V 24V V 26.4V 24V BMB24H BMB24F21 291

285 Blower 12 mm San Ace B12 32mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 12mm 32mm Mass 27g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19BF12HC , to BF12MC , BF24HC , to BF24MC , to 6 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Blower 97mm/12mm Dimensions Unit : mm Lead Wire AWG24 UL AIR FLOW Rotating Direction Mounting Hole Air Flow Direction Air Flow - Static Pressure Characteristics H speed 13.8V/27.6V 12V/24V 1.2V/2.4V M speed 13.8V/27.6V 12V/24V 1.2V/2.4V 12mm BF12HC2 19BF24HC BF12MC2 19BF24MC

286 Blower 12 mm San Ace B12 32mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 With PWM speed control function Refer to Page 311 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-) Expected Life Varies for each model (L1:Survival rate: 9% at 6, rated voltage, and continuously run in a free air state) Lead Wire red black Sensor yellow Control brown Storage Temperature 3 to 7 Non-condensing 12mm 32mm Mass 34g Specifications Rated Voltage Operating Voltage Range PWM duty Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life Note2) Model No. V V cycle Note1) % A W min -1 m³/min Pa inchh ² O db(a) h 9BFB12P2H to , , ,/ , , to 7 9BFB24P2H to 26.4 (7,/4 ) , Note 1 : 9BFB12P2H3 9BFB24P2H3 does not rotate when PWM duty cycle is %. Note 2 : Expected life at 4 ambient is just reference value. PWM Frequency 25kHz Available upon request for all the models above. Dimensions Unit : mm 3 (1) 3 Lead Wire AWG24 UL (2) (28) (2) (2) (63.7) (.8) (56) 3-R (63.8) (7.5) (15) (22) 12 1 (71.7) Air Flow Direction (5) Mounting Hole (15) (22.5) (7.5) Rotating Direction 293

287 Air Flow - Static Pressure Characteristics PWM Duty Cycle H speed DC 12V 1,6 6. 1,4 5. 1,2 4. 1, PWM Duty Cycle 1% % BFB12P2H3 Static Pressure 1,6 6. 1,4 5. 1,2 4. 1, H speed DC 24V PWM Duty Cycle 1% 5% % BFB24P2H3 Operating Voltage Range 1,6 6. 1,4 5. 1,2 4. 1, H speed PWM PWM 1 Duty Cycle 13.2V 12V 1.8V Air Flow 9BFB12P2H3 Static Pressure 1,6 6. 1,4 5. 1,2 4. 1, PWM PWM 1 Duty Cycle 26.4V H speed 24V 21.6V Air Flow 9BFB24P2H3 12mm Blower 12mm PWM Duty - Speed Characteristics Example Rotation min Speed min -1-1 Voltage DC12V DC12V PWM 25kHz Frequency 25kHz 7, 7,min , 5, 4, 3, 2, 1, When 8Pa fan operates at 8 Pa static pressure 5,min Pa When fan operates at 35 Pa static pressure 3,75min -1-1 Free air, when fan operates at no static pressure Rotation min Speed min -1-1 DC24V Voltage DC24V PWM 25kHz Frequency 25kHz 7, 7,min , 5, 4, 3, 2, 1, When fan 85Pa operates at 85 Pa static pressure 5,min Pa When fan operates at 5 Pa static pressure 3,75min -1-1 Free air, when fan operates at no static pressure 1 PWM PWM % Duty Cycle % 9BFB12P2H3 1 PWM PWM % Duty Cycle % 9BFB24P2H3 12mm 294

288 Blower 127mm San Ace B127 32mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 127mm 32mm Mass 29g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19BJ12HC , to BJ12MC , BJ24HC , to BJ24MC , to 7 1 to 6 4, Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm AIR FLOW Lead Wire AWG24 UL Mounting Hole Rotating Direction Air Flow Direction Air Flow - Static Pressure Characteristics H speed V/27.6V 12V/24V 1.2V/2.4V BJ12HC2 19BJ24HC M speed V/27.6V 12V/24V 1.2V/2.4V BJ12MC2 19BJ24MC2 1.5

289 Blower 16 mm San Ace B16 4mm thick General Specifications With a pulse sensor Specifications for pulse sensors Refer to Page 39 Material Frame: Plastics (Flammability: UL94V-), Impeller:Plastics (Flammability: UL94V-1) Expected Life Varies for each model(l1:survival rate: 9% at 6, rated voltage,and continuously run in a free air state) Lead Wire red black or blue Sensor yellow Storage Temperature 3 to 7 Non-condensing 16mm 4mm Mass 58g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Max. Air Flow Max. Static Pressure SPL Operating Temperature Expected Life V V A W min -1 m³/min Pa inchh ² O db(a) h 19BG12HC , to BG12MC , BG24HC , to BG24MC , to 6 4, Blower 16mm Without Sensor Pulse Sensor Available upon request for all the models above. Lock Sensor Please inquire as the availability of these functions depend on the model. Dimensions Unit : mm +3 3 (1) Lead Wire AWG24 UL Mounting Hole Mounting Hole AIR FLOW Rotating Direction Air Flow - Static Pressure Characteristics Air Flow Direction 16mm H speed V/27.6V 12V/24V 1.2V/2.4V BG12HC1 19BG24HC M speed V/27.6V 12V/24V 1.2V/2.4V BG12MC1 19BG24MC

290 CPU Cooler Intel 775-land LGA Package CPU Cooler SAN ACE MC General Specifications Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-1) Heatsink: Aluminum (Core: Copper) Lead Wire yellow (Connector No.2 side) black (Connector No.1 side) Sensor green (Connector No.3 side) Control blue (Connector No.4 side) Connector Molex P/N or Wieson 251C888-1 Contact Molex P/N 5159PBT or Equivalent or Wieson 2511-T1 Mass 575g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Speed c-a Thermal Resistance SPL Operating Temperature Expected Life V V A min -1 K/W db(a) h 19X9112PTH to , , to 7 4, Dimensions Unit : mm 9 1 ( 96) ( 96.8) Thermal pad Honeywell PCM45F Lead Wire AWG26 UL143 Fan speed characteristics Control input PWM duty - Fan speed characteristics PWM Waveform of control input PWM signal input : between blue lead wire and black lead wire Voltage DC12V PWM Frequency 25kHz VOL:V VOH:5V 4 Speed min At At VOH VOL t T VOH:5.25V DC VOL:.8V DC or Less PWM Duty = t / T 1 f = 1 / T = 21 to 28 khz Control input Current I SOURCE MAX.:5 ma (AT V CONTROL VOLTAGE) I SINK MAX.:5 ma (AT 5V CONTROL VOLTAGE) Input PWM duty 1 297

291 CPU Cooler Intel Pentium 4 Processor 775-land LGA Package CPU Cooler SAN ACE MC General Specifications Material Frame: Plastics (Flammability: UL94V-), Impeller: Plastics (Flammability: UL94V-1) Heatsink: Aluminum (Core: Copper) Lead Wire yellow (Connector No.2 side) black (Connector No.1 side) Sensor green (Connector No.3 side) Control blue (Connector No.4 side) Connector Molex P/N or Wieson 251C888-1 Contact Molex P/N 5159PBT or Equivalent or Wieson 2511-T1 Mass 49g Specifications Model No. Rated Voltage Operating Voltage Range Rated Current Rated Speed c-a Thermal Resistance SPL Operating Temperature Expected Life V V A min -1 K/W db(a) h 19X9212PTH to Dimensions Unit : mm 3, , to 7 4, CPU Cooler Lead Wire AWG26 UL143 Thermal pad Honeywell PCM45F Fan speed characteristics Control input PWM duty - Fan speed characteristics Voltage DC12V PWM Frequency 25kHz VOL:V VOH:5V Speed min At At 3 22 PWM Waveform of control input PWM signal input : between blue lead wire and black lead wire VOH VOL t VOH:5.25V DC T VOL:.8V DC or less Duty = t / T 1 f = 1 / T = 21 to 28 khz Control input Current I SOURCE MAX.:5 ma (AT V CONTROL VOLTAGE) I SINK MAX.:5 ma (AT 5V CONTROL VOLTAGE) Input PWM duty 1 298

292 Fans with PWM speed control function Technical Material Refer to Page 311 There are following part numbers except ones with With PWM speed control function marking in the text. Available size and example of characteristics Please inquire our sales department for specifications other than the following. Closed Loop Control ( No mark denotes open loop control. ) Photo shows mm fan. Size mm Model No. Frame material Voltage V PWM Frequency khz Current A Rated Speed min -1 Max. Air Flow Max. Static Pressure SPL Duty Cycle Pa inchh2o db(a) 1% Duty Cycle % mm 9GV3612P3J3 Plastics ,2 19, , 9GV3612P3G3 Plastics ,2 14, , mm 9GV312P3J3 Plastics , 15, , mm 19P412P3J33 Plastics , , 19P412P3G33 Plastics , , 9PH412P3K33 Plastics ,2 15, , 9GV412P3J2 Plastics ,65 14, , 9GV412P3K3 Plastics , 16, , 9GV412P3J3 Plastics ,65 14, , 9GV412P3G3 Plastics ,4 13, , mm 9CRA412P5J3 Plastics Inlet : 2,85 Inlet : 15,8 outlet : 2,25 outlet : 12, , 9CRA412P5K3 Plastics CR412P5S3 Plastics CRA412P5G3 Plastics Inlet : 3,5 outlet : 2,3 Inlet : 3,3 outlet : 2, Inlet : 2,8 outlet : 2,15 Inlet : 17, outlet : 13, Inlet : 15,8 outlet : 1,6 Inlet : 14, outlet : 1,4 Expected Life h , , , mm 9AH612P4G3 Plastics ,12 5, , 9AH612P4H5 Plastics , , mm 9G612P1G3 Plastics ,55 11, , 9G612P1G4 Plastics , , 9G612P1M3 Plastics ,2 6, , mm 9CR612PS3 Plastics Inlet : 1,3 Inlet : 11,5 outlet : 8 outlet : 7, , 9CR612PH3 Plastics Inlet : 1,2 outlet : 8 Inlet : 1,3 outlet : 6, , mm 9PH812P7S6 Plastics , 4, , mm 9AH812P4H4 Plastics , , mm 9G812P1G4 Plastics ,2 6, , 9G812P1H3 Plastics , 5, , 9G848P1G3 Plastics ,5 6, , 8 8 8mm Inlet : 2, Inlet : 8, 9CR848P8S3 Plastics outlet : 1,3 outlet : 5, , mm 9AH912P4G3 Plastics , , 9AH912P4H3 Plastics , , mm 9G912P2G3 Plastics ,2 5, , 9G912P2B3 Plastics ,2 4, , mm 9G912P1G3 Plastics , 5, , mm 9G1212P4G3 Plastics , 4, , 9G1212P4G31 Plastics , 4, , mm 9SG1212P1G1 Aluminum SG1224P1G1 Aluminum ,9 (Duty cycle 5%) 3,6 (Duty cycle 5%) 6, , 6, , 9SG1248P1G1 Aluminum ,6 (Duty cycle 5%) 6, , mm 9GV1512P5M3 Plastics , , 172mm 51mm thick Side Cut Type 19E5712P5K4 Aluminum , , B97mm 33mm 9BAM12P2G9 Plastics ,8 6, , Rated current, maximum air flow, maximum static pressure, and sound pressure level are the values given when duty cycle 1%. Storage temperature is -3 C to +7 C. For operating temperature range, see individual specification sheet. Switching with the PWM control may affect the sensor output. Specifications may be changed without notice. 299

293 Custom Product Cooling Fan Units Features We provide assembled fan units in accordance with the specification or requirements of the equipment. For use in communications equipment, servers, storage systems. Example of application : Cooling Fan Unit Electrolytic Corrosion Proof Fans Example of application : Cooling Fan Unit for 1U Server Features This cooling fan prevents electrolytic corrosion of bearings even under conditions where electromagnetic noise is generated. Electrolytic corrosion of ball bearings is prevented by using ceramic balls in ball bearings. The ceramic material is an insulating material. Manufacturable to meet specifications of all San Ace series fans. Impeller Technical Material Refer to page 314 Fans with PWM speed control function / Custom Product Magnet Stator Bearing:Ball Bearing Material of ball:ceramic Coil Caution Electrolytic Corrosion Proof Fan has been designed to prevent the electrolytic corrosion of ball bearings in the fan, but this does not guarantee that the fan will operate normally under conditions where there is strong electromagnetic noise. Please be sure to fully evaluate the value of fan malfunction due to noise in advance. 3

294 Option Finger guards Dimensions(Unit : mm) 36mm sq. type Model Surface treatment Nickel-chrome plating silver 38mm sq. type 4mm sq. type Model Surface treatment Nickel-chrome plating silver Model Surface treatment Nickel-chrome plating silver mm sq. type Model Surface treatment Nickel-chrome plating silver 52mm sq. type Model E Surface treatment Nickel-chrome plating silver 6mm sq. type Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side mm sq. type Model 19-49C Surface treatment Nickel-chrome plating silver 8mm sq. type 92mm sq. type Model 19-49E 19-49H Surface treatment Nickel-chrome plating silver Cation electropainting black Model 19-99C Surface treatment Nickel-chrome plating silver Outlet side Outlet side mm sq. type Model 19-99E 19-99H Surface treatment Nickel-chrome plating silver Cation electropainting black 12mm sq. type Model 19-19C 19-19H Surface treatment Nickel-chrome plating silver Cation electropainting black 12mm sq. type Model 19-19E 19-19K Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side

295 16 Finger guards Dimensions(Unit : mm) 127mm sq. type Model Surface treatment Nickel-chrome plating silver 127mm sq. type Model Surface treatment Nickel-chrome plating silver 133mm type Model Surface treatment Nickel-chrome plating silver Outlet side 119 ( 6) mm sq. type Model Surface treatment Nickel-chrome plating silver 14mm sq. type Model H Surface treatment Cation electropainting black 15mm sq. type Model Surface treatment Nickel-chrome plating silver Option mm sq. type Model Surface treatment Nickel-chrome plating silver 15mm type Model Surface treatment Nickel-chrome plating silver Outlet side Inlet side ) mm SideCut type Model J Surface treatment Nickel-chrome plating silver Applicable Model: 9SG57**P5***/9GV57**H51 9CR5748PG1/9WG5748P5*1 For the finger guard Model: J, fix the finger guard to four holes as shown in the diagram. Finger guards Plain washers Spring washers Screws Hexagonal nuts Fan

296 Option Finger guards Dimensions(Unit : mm) 172mm SideCut, Round type 172mm SideCut, Round type Model E H Surface treatment Nickel-chrome plating silver Cation electropainting black Model Surface treatment Nickel-chrome plating silver Outlet side For the finger guard Model: E, H, 19-32, fix the finger guard to two holes as shown in the diagram. Do not fix it to any other holes Finger guards Plain washers Hexagonal nuts Spring washers 152 Screws Fan 172mm Round type Model Surface treatment Nickel-chrome plating silver 172mm Round type Model Surface treatment Nickel-chrome plating silver Outlet side mm type Model H Surface treatment Nickel-chrome plating silver Cation electropainting black 2mm type Model H Surface treatment Nickel-chrome plating silver Cation electropainting black Outlet side Mounting example Axial fan Centrifugal fan Hexagonal nuts Finger guard Plain washers Spring washers Screws Inlet nozzle Finger guard Fan Hexagonal nuts Fan Plain washers Spring washers Screws Chassis 33

297 1.5 Inlet nozzle for centrifugal fan and splash proof centrifugal fan Nozzle mounted in fan inlet side to adjust the flow of introduced air. Dimensions(Unit : mm) 1mm type mm type Model Model Each Each R mm type mm type Model Model Each Each R6 O R1 EMC guards Dimensions(Unit : mm) Option 8mm sq. type Model Surface treatment Nickel-chrome plating silver Applicable Model 19P8***6**/19P8***2** 19L8***4** 8mm sq. type Model Surface treatment Nickel-chrome plating silver ø1.6 ø1.6 ø ø ø ø43 99 ø11.2 ø11.2 ø ø ø172 1 ø ø ø ø72 ø152 Applicable Model 19P8***7**/19R8***4**/9A8***4** 92mm sq. type Model Surface treatment Nickel-chrome plating silver Applicable Model 19P9***4**/19L9***4** 12mm sq. type Model Surface treatment Nickel-chrome plating silver Applicable Model 9G12***4** 9G12***1**/9LB12***1**/9GL12***1** 172mm type Model Surface treatment Nickel-chrome plating silver Applicable Model 19E47***4**/19E17***5**/19E57***5** 9GV57***5**/19L17***5** ø148 34

298 Option Resin finger guards Dimensions(Unit : mm) Material Frame (SPS PS alloy) Resin UL File No.E V 6mm sq. type Model 19-13G 8mm sq. type Model 19-12G ø ø mm sq. type Model 19-11G ø mm sq. type Model 19-1G ø Air Flow and Static Pressure Characteristics Static pressure Pa Measured using Sanyo airflow chamber 12mm sq. type 9 8 Note: resin fingerguard 7 (19-1G) during mounting Fan unit 3 (19R1212H12) 2 Voltage: DC12V 1 Note: Finger guard is attached on air inlet side of fan Air flow Resin filter kits Mounting example Guard Chassis Small pan-head screws (4) Fan Hexagonal nuts (4) Plastic finger guards are placed on both the intake and exhaust sides of the fan. No nuts or screws for use in attachment included. Dimensions(Unit : mm) 6mm sq. type Model 19-13F13 13PPI 19-13F2 2PPI 19-13F3 3PPI 19-13F4 4PPI ø mm sq. type Material Guard,cover (SPS PS alloy) Resin UL File No.E V Filter Polyurethane foam UL File No.E74916(S) 94HF 1 Model 19-12F13 13PPI 19-12F2 2PPI 19-12F3 3PPI 19-12F4 4PPI ø ø1.5 92mm sq. type Model 19-11F13 13PPI 19-11F2 2PPI 19-11F3 3PPI 19-11F4 4PPI ø ø1.5 12mm sq. type Model 19-1F13 13PPI 19-1F2 2PPI 19-1F3 3PPI 19-1F4 4PPI ø ø Air Flow and Static Pressure Characteristics 4 ø PPI Particles Per Inch : Indicates the number of holes per inch. Note that the higher the number, the finer the grain of the sponge. Reference Diagram For Mounting Hexagonal nuts (4 Static pressure Pa For the Sanyo double chamber unit 12mm sq. type 9 8 Fan unit 7 19R1212H Air flow Filter kit is one of the option to keep air in the chassis clean filtering dust in external atmosphere when pulling-air cooling is implemented. The filter kit is hooked up through mounting hole of fan frame with screw as well as finger guard. Some performances(airflow & static pressure) of the fan motor decreases when filter kit is hooked up. This Filter Kit is composed of 3 components, including a guard, a filter and a cover. It is delivered as a finished product at delivery, saving assembly time when mounting. It can be mounted by inserting a screw in the apertures of the cover. The filter and cover can be easily removed from the guard with one touch. There is no need for fan removal when undertaking maintenance. Operating temperature limit is between 1 to 6.(non condensing) The filter will deteriorate with age, and the level of deterioration will vary upon usage conditions. Please be aware that the filter has a greater tendency to deteriorate under high temperature and humidity.for long-term storage, please store under the temperature range of 1 to 3, humidity range of 2% to 65%. Usage and storage period is approximately 2 years. Cooling ability decreases with filter contamination due to clogging. Filter replacement is recommended approximately every six months of usage. Please replace the filter if deterioration or clogging is seen at inspection. When replacing the filter, please use genuine SANYO DENKI filters. Do not water-wash the filter. Avoid use and storage under high temperature or humidity, direct sunlight or exposure to ultraviolet light, or in corrosive gas. No nuts or screws for use in attachment included Note: Filter kit 19 1F2 during mounting Applied voltage: DC12V Note: Filter kit is attached on air inlet side of fan For fixing screws Apertures (4 locations) Chassis Filter kits Small pan-head screws (4) Fan Replacement filter (5 sheets each) 6mm sq. type 19-13M13 13PPI 19-13M2 2PPI 19-13M3 3PPI 19-13M4 4PPI 92mm sq. type 19-11M13 13PPI 19-11M2 2PPI 19-11M3 3PPI 19-11M4 4PPI 8mm sq. type 19-12M13 13PPI 19-12M2 2PPI 19-12M3 3PPI 19-12M4 4PPI 12mm sq. type 19-1M13 13PPI 19-1M2 2PPI 19-1M3 3PPI 19-1M4 4PPI

299 Recommended connectors for DC fans Manufacturer MOLEX Tyco Electronics AMP Hirose Japan Aviation Electronics Industry Japan Solderless Terminals 2 pins Housing model number :P/N pins Housing model number :P/N :P/N RP pins Housing model number :P/N Contact model number :P/N 5159T :P/N 5159PBT :P/N 2759T :P/N :P/N :P/N :P/N 5263PBT :P/N R :P/N R 39 59:P/N 5556PBT 39 38:P/N 5556T DF1B 2EP 2.5RC DF1B 3EP 2.5RC DF1B 2428PCF DF3 2EP 2C DF3 3EP 2C DF3 4EP 2C DF3AA 2EP 2C DF3AA 3EP 2C DF3AA 4EP 2C DF3 EP2428PCF IL 2S S3L (N) IL 3S S3L (N) IL 4S S3L (N) IL C2 1 1 IL G 2S S3C2 SA IL G 3S S3C2 SA IL G 4S S3C2 SA IL G C2 SC 1 EHR 2 EHR 3 EHR 4 SEH 1T P.6 SMP 2V BC SMP 3V BC SMP 4V BC SMP 2V NC SMP 3V NC SHF 1T.8BS H2P SHF AA H3P SHF AA PHR 2 PHR 3 PHR 4 SPH 2T P.5S XAP 2V 1 XAP 3V 1 XAP 4V 1 XMP 2V XMP 3V SXA 1T P.6 XHP 2 XHP 3 XHP 4 SXH 1GU P.6 SXH 1T P.6 SMR 2V B SMR 3V B SMR 4V B SMR 2V N SMR 3V N SMR 4V N SYM 1T P.6 Note : The specifications in this table are for reference purposes only. When selecting, please check catalogs of each brand. Thermistor 3.5Max Model (Unit : mm) 2±5 Option 3 7 5±1 5±1 Number Name Standards, materials, etc. Thermistor Chip Insulated cord Epoxy resin Lead UL2555 CSA TR-64 AWG#28 blue Item Spec 2-1 Resistance R25 6.8K 3% 2-2 B constant B25/5 395K 2% 2-3 Maximum 188mW(25 under still air) 2-4 Insulation resistance 1M or more(5 VDC megger) 2-5 Dielectric strength No problem(1,5 VAC, 1 minute) 2-6 Operating temperature range 3 to Storage temperature range 4 to 1 Manufactured by OHIZUMI MGF CO.,LTD. IC L873 for DC fan sensor Characteristics Startup delay L873 doesn't output signal until fan normally runs after start-up Input type Single input: L873 can input digital signal of Vov and GND Supply voltage range 5V.5V Output current 1mA max.(sink/open drain output) The output with latch is also availble Noise margin Malfunction-protective circuit in embedded Model Stick type (set of 95): L873-1 Reel type (set of 1,5): L873-2 Dimensions(Unit : mm) 5.5 R OUT1 OUT2 Vss C COM VIN VDD TYP.42.2 Application Use it for your receiving circuit of a our DC fan (with a pulse sensor). R2 Vcc 2 C1 R1 1 8 * 3 7 Alarm L873 output E D K Vcc F E: Power supply for fan drive circuit Vcc 5V.5V At normal speed [H]: Vcc At abnormal speed [L]:.5V MAX. * : Trip Insert speed a D1 in case of C1 E > Vcc. min -1 PF R1 K R2 K Startup delay sec 85 1, , ,

300 Technical Material Overview and characteristics of fan Overview A cooling fan is widely used to extend life of your system by cooling off heat of the system that many electrical components are mounted in a very high density and dissipating heat. Since we Sanyo Denki developed San Ace which is the first AC fan in Japan in 1965, we have increased fan motor lineup until now meeting customer s needs rapidly based on our tremendous career. We Sanyo Denki will continue to develop new fans with high air flow, low noise, low vibration, and energy - saving design. Characteristics We can roughly devide fan into two types which are AC and DC. AC Fans Sanyo Denki succeeded in the mass-production of AC fans in Sanyo Denki was the first Japanese manufacturer to have succeeded at this. High performance High reliability Safety DC Fans Sanyo Denki succeeded in the mass-production of DC fans in High performance Low power consumption Low vibration Low leakage of flux High reliability Sanyo Denki currently has a wider variety of products like Long Life Fan, CPU cooler, Splash Proof Fan, and Oil Proof Fan etc to meet all customer needs. Guideline in selecting a fan How to select an appropriate fan The following example is a guideline regarding how to select an appropriate fan for cooling your system 1. Determining of your system specifications and conditions Determine the temperature rise inside your system and obtain the total heating value inside your system on the basis of its inputs and outputs. Example V : Total heating value of your system W =1 W T : Inside temperature rise K =15 K 2. Calculating the Required Air flow for Cooling After the equipment specifications and conditions of your system have been determined, calculate required air flow to meet the conditions. (Note that the formula shown below only applies when the heat radiation is performed only by cooling air from the fan.) Example Q': Motion air flow V 1 W Q = = 2 T 2 15 K.33 m3 /min 3. Selecting the Fan After the motion air flow has been calculated, select an appropriate fan motor based on the value.the motion air flow when the fan motor is actually mounted in your system can be obtained using the air flow-static pressure characteristics curve and system impedance. However, the system impedance cannot be measured without a measuring equipment, so fan with 1.5 to 2 times higher air flow than the actual Max air flow should be selected (operating air flow is one-third to two-thirds of maximum air flow). Example Q: Maximum air flow Q =Q 2/3 Q=Q 3/2=.33 3/2.5 Next, In case that you select a fan having an air flow of.5 (m 3 /min) or more and a appropriate size for the space inside your system. For example, If you need a fan of 6mm square, 25mm thickness and 12V, you should select is 19R612H42 (maximum air flow =.53m 3 /min). V Static pressure Pressure loss T Heat source System Fan Characteristics of air flow versus static pressure and those of pressure losses of equipment System impedance Q' 4. Confirming the Selected Fan Calculate the temperature rise inside your sysetem when your sysetem having 1 (W) of total heating value is forcefully cooled down by a 19R612H42 fan. Example Q =Q 2/3=.53 2/3.353 T =V/2Q =1 W / K From the above, the temperature rise inside your system is calculated as 14.2 K. Operating air flow Air flow Since the value obtained from the above equation is only a rough target, final fan selection should be based on your actual installation test. 37

301 Characteristics calculation method and description Reliability and Life Expectancy A cooling fan generally cools itself as well. The temperature rise of the motor is relatively low and the temperature rise of the grease in the bearings is also low, so expected life is longer than general some either motors. Since the service life of bearings is a theoretical value that applies when they are ideally lubricated, the life of lubricant can be regarded as expected life of the fan. DC fan consumes less power and its temperature rise of bearing is very low, thus its expected life is 4, hours at an ambient temperature of 6 (6, hours for some models). Sanyo Denki also has a line-up of long life fans that has 2, hours life and 1, hours life at an ambient temperature 6 with an even more enhanced structure and material. When the measurement conditions are: L1 (the remaining product life in the lifespan test is 9%),with an atmospheric temperature of 6 degrees, at the rated voltage, and continuously run in a free air state. The table below indicates the relationship between ambient temperature and expected life estimated on the basis of our life tests and same other tests conducted by Sanyo Denki. An accelerated life test is conducted on the basis of the concept that the expected life halves as the ambient temperature rises by about 15 (within the operating temperature range of lubricant.) Expected life of DC Fans Life expectancy H Expected life 6h(L1, 6 ) Expected life 4h(L1, 6 ) Expected life 2 (L1, 6 ) Expected life 1h L1, 6 ) Ambient temperature Rated voltage, continuously run in a free air state, survival rate of 9% Noise characteristics Noise is average value that measured at l meter away from air intake side of fan that is suspended on special frame in anechoic chamber (as per JIS B 833). Fan Noise meter AIR FLOW 1m Technical Material Acoustic radio wave anechoic chamber Noise characteristic measurement equipment Measuring air flow and static pressure It is very difficult to measure air flow and static pressure. In fact, the performance curve may vary greatly according to the type of measuring equiment. The commonly-used type of measuring equipment is a wind tunnel using a Pitot tube. Sanyo Denki uses a very precise method using double chamber equipped with many nozzles. Ps U-shaped tube Pn Chamber A U-shaped tube Chamber B Nozzle Throttle device BM Fan to be measured Auxiliary blower Double chamber measuring equipment Q 6Av A where Q = air flow A = cross sectional area of nozzle 4 D2 m 2 D = nozzle diameter v = average air flow velocity of nozzle 2g Pn m/sec : Air specific gravity kg/m 3 1.2kg/m 3 at 2, 1 atmospheric pressure g = acceleration of gravity = 9.8 m/sec 2 Pn= differential pressure mm H 2 O Ps = static pressure mm H 2 O The measuring equipment using double chanber is method to be calculated from air flow goes through nozzle and differential pressure between pressure of inside of chamber (Ps) and atomospheric pressure by measuring differetial pressure between air intake and exhaust of nozzle (Pn). Conversion Table Static pressure 1mm H 2 O.394inch H 2 O 1mm H 2 O 9.8Pa Pascal 1inch H 2 O 25.4mm H 2 O 1Pa.12mm H 2 O 1inch H 2 O 249Pa Air flow 1m 3 /min 35.31ft 3 /min 1CFM.283m 3 /min 1m 3 /min /sec 1CFM.472 /sec 1 /sec.6m 3 /min 38

302 Technical Material DC Fan Common Specifications Material Frame,Impeller:Plastics / Frame:Aluminum,Impeller:Plastics * CPU cooler excluded. For details, refer to the appropriate page. Life Expectancy Varies for each model(l1:survival rate:9% at 6,rated voltage,and continuously run in a free air state) * Splash proof fan: Varies for each model(indoor, L1:Survival rate:9% at 6,rated voltage,and continuously run in a free air state) Motor Protection Burnout protection at locked rotor condition and Reverse polarity protection Dielectric Strength DC Fan AC5/6Hz 5VAC 1minute(between lead conductor and frame) CPU Cooler AC5/6Hz 5VAC 1minute(between input terminal and frame) Insulation Resistance 1M or more at 5VDC megger (between lead conductor and frame) Sound Pressure Level(SPL) Expressed as the value at 1m from air inlet side Storage Temperature -3 to +7 (Non-condensing) Lead Wire For details, refer to the appropriate page. Overheating protection function Protection Functions: If the fan blades are restricted, an overcurrent occurs and leads to a rise in the fan coil temperature. This can result in reduced performance, damage, or a fire. To prevent this from occurring, Sanyo Denki s fans incorporate an overheating protection function. Refer to the catalog for the types of protection functions. Burnout protection function at locked rotor condition Current cutoff system If the fan blades are restricted, the coil current is cut off at regular cycles to prevent overheating of the coil. When the hindrance is removed, the fan restarts automatically. (For the San Ace 2 Model.No:19E2******, however, the power needs to be turned off and on again to restart.). Reverse polarity protection function No problem about fan even if positive & negative lead are connected in reverse. (However fans with sensor & speed control are excluded.) Specifications for DC fan sensors Pulse sensor (Tach output type) example Pulse sensor outputs two pulse waves per revolution of fan, and it is good to detect fan speed. Pulse sensors can be incorporated in all kinds of DC fans. * Noise from inside the fan or from external devices may effect sensor output. Contact us for more information. The special IC that detects a pulse sensor and raises the alarm is available. Refer to page 36. Typical standard model: 9G1212H11. Output circuit Open collector Output waveform(need pull-up resistor) In case of steady running Specifications VCE 3V MAX. For a 48V-rated fan:vce 6V MAX. Ic 1mA MAX. Vol Vce SAT.4V or less Inside of DC fan VOH VOL V T1 One revolution T T2 T3 T4 SENSOR Resistor 3V MAX. Ic 1mA MAX. Sensor output T1 to 4 1/4 T T1 to 4 1/4 T 6/4N sec N Fan speed min -1 * If you want detailed specifications that apply when the rotor is locked, please contact Sanyo Denki. 39

303 Locked rotor sensor (rotation/lock detection type) example Locked rotor sensor outputs fan status signals. It is good to check whether the fan is running or locked * Noise from inside the fan or from external devices may effect sensor output. * Regarding details of the reverse logic and specifications of lock sensor output signals, please contact Sanyo Denki. * Lock sensor can not be used in some models. Contact us for more information. Typical standard model: 9G1212H1D1. Output circuit Open collector Specifications VCE 27.6V MAX. For a 48V fan VCE 6V MAX. Ic 5mA MAX. VOL VCE SAT.6V or less For a 48V fan:vce SAT.4V or less Inside of DC fan Output waveform (Need pull-up resistor) VOH VOL V Rotor running Rotor locked Rotor running.5 or less 5 or less 3 or less Time sec SENSOR Resistor 27.6V MAX. Ic 5mA MAX. Sensor output Note: The output is completely at Vol with.5 seconds or less after power-up. Low-speed sensor (rotating speed detection type) example Low-speed sensor outputs a signal when fan speed goes down to trip point or less. It is good to detect cooling degradation of fan. *Noise from inside the fan or from external devices may effect sensor output, please. * If you want detailed specification and reverse signal output,please contact Sanyo Denki. (typical standard model: 19R1212H1H1) *Low-speed sensors can not be used in some models. Contact us for more information. Technical Material Typical standard model: 9G1212H1H1. Output circuit Open collector Specifications VCE 27.6V MAX. Ic 1mA MAX. VOL VCE SAT.5V or less Inside of DC fan SENSOR Resistor 27.6V MAX. Ic 1mA MAX. Sensor output Sensor scheme Example 1: In case steady running Fan power Example 2: In case that the rotor is locked when the fan motor is turned on and released after the start-up delay time. Fan power Fan speed Trip point Fan speed Trip point Startup delay Sensor output H Detected delay L VCE SAT H Sensor output Startup delay H L Detected delay H 31

304 Technical Material PWM Speed Control Function The PWM speed control function is a function that externally controls the rotation speed of the fan by changing the duty of the input pulse signal between the control terminal and GND. It regulates optimum airflow for efficient cooling when necessary, and is effective for lowering power consumption and reducing equipment noise level. * Some models can not have PWM speed control function. Contact us for more information. Typical standard model: 9GV812P4K3 PWM Duty - Speed Characteristics 7 6 Voltage : 12V DC PWM Frequency 25kHz 63min -1 5 Duty cycle 2% Fan speed Speed min min -1 23min -1 A B 5V V Duty cycle 5% 5V V 36% speed 23min -1 of full speed 65% speed 41min -1 of full speed Duty cycle 1% 1 C 5V V Full speed 63min -1 % 2% A 5% B PWM Duty Cycle 1% C PWM Input Signal Input Signal Wave Form VIH VIL T1 T VIH = 4.75V to 5.25V VIL = V to.4v PWM Duty Cycle(%) = PWM Frequency 25 (khz) = T1 1 T 1 T Source Current ( I source ) : 1mA Max. at control voltage V Sink Current ( I sink ) : 1mA Max. at control voltage 5.25V Control Terminal Voltage : 5.25V Max. ( When control terminal is opened ) When the control lead wire is open, speed is same as one at 1% PWM duty cycle. This fan speed should be controlled by PWM input signal of either TTL input or open collector, drain input. Example of Connection Schematic DC fan power Inside of DC fan Source Current ( I source ) : 1mA Max. at control voltage V Sink Current ( I sink ) : 1mA Max. at control voltage 5.25V Control Terminal Voltage : 5.25V Max. ( When control terminal is opened ) Control Terminal PWM signal Isource Isink 311

305 Splash Proof Fan "IPXX" Protection Grade IP code is laid down in "Degrees of protection provided by enclosures (IP Code) " on JIS C 92 and IEC IP code is defined as "A coding system to indicate the degree of protection provided by an enclosure against access to hazardous parts, ingress of solid foreign objects, ingress of water and to give additional information in connection with such a protection" Regarding IP code, the first numeral indicates the degree of protection against access to hazardous parts and ingress of solid foreign objects. The second numeral indicates the degree of protection against the ingress of water. I P X X Protected against splashing water (Water splashed against the enclosure form any direction shall have no harmful effects) Protected against water jets (Water projected in jets against the enclosure form any direction shall have no harmful effects) Dust-Protected (Ingress of dust is not totally prevented, but dust shall not penetrate in a quantity to interfere with satisfactory operation of the apparatus or to impair safety.) First characteristics Degree Type Description No protected device Rotating device without special protection. 1 Semi-protected device Rotating device with protection against solid objects of 5mm or larger Protected device Shielded device Totally shielded device Dust resistant device Dust-proof device Rotating device with protection against solid objects of 12.5mm or larger Rotating device with protection against solid objects of 2.5mm or larger Rotating device with protection against solid objects of 1mm or larger Rotating device with protection against harmful dust ingress (dust protected) Rotating device with totally protection against any dust ingress (dust tight) Technical Material Second characteristics Degree Type Description No protected device Drip-proof device (Grade I) Drip-proof device (Grade II) Rain-proof device Splash-proof device Jet-proof device Water resistant device Water immersion-proof device Submergence-proof device Rotating device without special protection. Rotating device with protection against falling water from the vertical Rotating device with protection against falling water to a maximum of 15 from the vertical Rotating device with protection against rain to a maximum of 6 from the vertical Rotating device with protection against water sprays from any direction. Rotating device with protection against water jets from any direction. Rotating device with protection against powerful water jets from any direction and no water ingress inside of the device. Rotating device with protection against the effects of temporary immersion in water under specific test condition. Rotating device with protection against the effects of permanent immersion in water of specific water pressure. 312

306 Technical Material Thermal speed controlled fans with an external or built-in thermistor External thermistor type 1. Overview For thermal speed controlled fans with an external thermistor, just connect a specified thermistor (or a specified thermistor and a resistor) between the control wire and the negative wire indicated in Fig. 1, it will enable the fan speed to change automatically according to a predetermined temperature speed specification and according to temperature changes in an environment where the thermistor is equipped.(please refe to Fig. 2) A thermistor can therefore be installed at an appropriate position inside your equipment to monitor the internal temperature changes due to changes in ambient temperature and heatup status (load status) of the equipment. Automatic monitoring can then specify low speed when the thermistor detects a temperature below TL, high speed when it detects a temperature above TH, and a speed according to the temperature when it detects a temperature between TL and TH. Thus, the fan detects its own operational status and determines the operating conditions. As a result, the thermal speed controlled fan with an external thermistor is designed that temperature changes according to the ambient temperature and operational status of the equipment are detected by the thermistor to control the fan's air flow (speed), and is near-ideal particularly in designing silent equipment. The fan thus meets the three requirements: silence, energy-saving, and long life. Change in speed 1 5 Fan Red Black Brown Low speed Control Fig. 1 High speed Variable speed in linear TL TH Thermistor temperature Fig. 2 E Thermistor 2. Setting temperatures (TL and TH) in low and high speed The standard products listed in this catalog are designed to run at a low speed at 28 or below and run at a high speed at 35 or more when a recommended thermistor is connected between the control wire and the negative wire. These temperatures (TL and TH) can be changed (as indicated in Table 1) by inserting a resistor in series with the thermistor. Fan Control Resistor Rs Recommended thermistor Table 1 Resistance Rs Temperature setting TL TH K K K K K 43 6 * For the resistor Rs, use a resistor rated at no less than 1/8W. * Manufactured by OHIZUMI MGF CO.,LTD. 3. If you wish to obtain low or high speed in a process of testing by using a larger equipment regardless of the thermistor temperature: Low speed : High speed : Instead of the thermistor, connect a 1 K resistor between the control wire and the negative wire. Connect the control wire directly to the negative wire. 4. Connecting the fan to the thermistor Sanyo Denki recommends to use connectors, including the power lead of the fan. Example of Typical connections :place a thermistor on the printed circuit board and connect the fan's power lead and control lead to the circuit pattern by means of connectors. Printed circuit board of the equipment Thermistor Connector Recommended connectors Manufacturer Model (3-pole) Japan Solderless Terminals XHP-3,SMR-3V-N Japan Aviation Electronics Industry IL-G-3S-S3C2-SA Japan AMP Molex Japan Typical applications of thermal speed controlled fans with an external thermistor Here are typical applications of a thermal speed controlled fan with a power supply where two 19P1212H42 fans are used (Fig. 5). (1) The fan selected was a 19P1212T4H12 thermal speed controlled fan having a performance equal to that of conventional fans at high speed. (2) The relationship between the temperatures of important components and those of the cooling fin can be measured with varied loads on the equipment and varied air flows of the fan. Since a correlation was determined, the thermistor can then be placed on the cooling fin, one of the important components. (3) Next, in view of the thermal design conditions of the equipment, the fan is set to high speed at an ambient temperature of 3 and an equipment load of 1%. (4) At an ambient temperature of 3 and an equipment load of 1%, the temperature of the cooling fin was 48 and the surface temperature of the thermistor placed on the cooling fin was 45 when the fan was running at high speed. It was therefore decided to add a 1.5 K resistor in series with the thermistor according to Table 1. In this case, the thermistor temperature is 35 and the fan runs at low (see Table 1 and Fig. 6). (5) Test results as installed on equipment: The thermal speed controlled fan displayed its full effect, thus being greatly advantageous in noise reduction. The ambient temperature during the test was dB A 33 Noise level reduction -9dB A 36 Cooling fan -6dB A 39-2dB A Rotation speed min -1 r.p.m Equipment noise (db (A)) Temperature rise in parts Rotating speed min operating point Input current of fan A Equipment load min Fig. 5 Fig. 6 Fig. 7 28min -1 Thermistor temperature * An ideal drop in the fan noise level was achieved according to the equipment load. When the equipment load was, the noise was 12dB (A) lower than in the case of conventional models. * The current consumption of the fan was 54% lower than in the case of conventional models when the equipment load was. * The noise level is expected to decline further at lower ambient temperatures.

307 Built-in thermistor type 1. Overview Thermal speed controlled fans with a built-in thermistor are designed that the fan it self contains a thermistor as indicated in Fig. 8. As illustrated in Fig. 9, the temperature of the air flowing through the fan motor is detected and the fan's speed changes automatically according to changes in that temperature. Fan Thermistor Red Black Fig. 8 E Rotation speed change 1 5 Standard values: TL = 3, TH = 4 Slow rotation TL TH Fast rotation Speed-variable domain Fig. 9 Temperature ( ) of air flowing through the fan UPS, inverter, rectifier, high-voltage power supply, etc. 2. Typical applications of thermal speed controlled fans with a built-in thermistor Fig. 11 indicates measurements taken when a 19R812T4H122 fan is mounted on equipment (a PC) is tested in the state as illustrated in Fig. 1. Heater PC Part temperature CPU Thermostatic chamber 19R812T4H122 Fig. 1 Temperature of air flowing through the fan Ambient temperature of equipment Rotation speed (min -1) Temperature ( ) Fig. 11 Fan rotating speed Part temperature CPU Temperature of air flowing through the fan Ambient temperature( )of equipment Cautions for use of a cooling fan in the vicinity of a power switching circuit (prevention of electrolytic corrosion) If a fan is installed near a large-power or high-voltage switching circuit, the heavy electromagnetic noise resulting from electromagnetic induction in such circuits or the influence of high-frequency noise imposed through the power line of the fan may induce current through the shaft bearing of the fan.such current may damage the oil film on the bearing and even the friction surface of the bearing.this adverse effect is known as "electrolytic corrosion of the fan."electrolytic corrosion affects the smooth revolution of the fan and may reduce its service life. An audible symptom is unusual noise emitted from the fan.this adverse effect is often observed and may partly be explained by the practice of mounting high-density parts, which reduces the gap between the switching circuits and the fan and the use of higher switching frequencies apt to provoke induction. Data processing/communications devices that operate at low voltages are not liable to electrolytic corrosion since they generate less electromagnetic noise. A Case of Electrolytic Corrosion Fans without anti-corrosion features installed near components that generate electromagnetic noise, such as inverter controllers, are liable to experience electrolytic corrosion. No. Use Period until the occurrence of unusual noise 1 Switching power supply 6 months to 2 years 2 UPS 6 months to 2 years 3 General-purpose inverter 1 to 1.5 years 4 Air cleaner 2 to 3 months 5 Inverter for LCDs 6 months The curve shown in the graph below represents the relationship between the level of the electromagnetic noise induced by a fan and the distance from the fan to the noise source. Level of noise induced by a fan Range in which electrolytic corrosion is generated Range in which electrolytic corrosion is not generated Distance from the noise source to the fan Custom Product Refer to page 3 Technical Material Occurrence of electrolytic corrosion Pattern 1 (1)The fan gets charged with high-frequency electricity by high-frequency noise (electric fi eld/magnetic fi eld) generated in the switching circuit. (2)Because of high-frequency electricity charged in the fan, an electric current flows through the bearing of the fan. (3)The electric current breaks the oil membrane on the surface of the bearing and the bearing gets abraded (electrolytically corroded). (4)This symptom often occurs in equipment in which switching circuits are sped up and implemented in high density. (5)Countermeasure 1: To provide a shield plate (Note 1) inside the fan (The plate should be such that does not interfere with air fl ow). (6)Countermeasure 2: To use a fan with ceramic bearings. Occurrence of electrolytic corrosion Pattern 2 (1)High-frequency electricity fl ows from the circuit board into the inside of the fan superimposed with the power line for the fan. (2)High-frequency electricity that has entered into the fan fl ows through the bearing. (3)Oil membrane on the surface of the bearing gets broken and the bearing gets abraded (electrolytically corroded). (4)Countermeasure 1: To remove high-frequency component between terminals "a" and "b", "a" and "e" and "b" and "e" of the power supply for the fan, or to insert a fi lter (Note 2) into the power line for the fan. (5)Countermeasure 2: To use a fan with ceramic bearings (6)Cables should be twisted in order to decrease induction to the power line for the fan. Switching circuit board of the equipment Component parts of the switching circuit + terminal a Power supply for the fan Vterminal b Circuit board grounding Note 1 Shielding metal plate As an electromagnetic shield metal, "EMC Guard" is available from our company. Certain shielding effect can be expected from mounting a general-purpose fi nger guard inside the fan. In each case, grounding to the cabinet is required. Note2 Filter Insert a common mode fi lter when the high-frequency electricity is superimposed on both lines "a" and "b" in the same phase and, if not, insert a normal mode fi lter. Measures against Electrolytic Corrosion (1) Relocate fans far from all electromagnetic noise sources. (2) Use anti-corrosion fans equipped with ceramic bearings. Refer to page 29 (3) Attach an EMC guard to ordinary fans. (4) As a power supply, the fan is wired from a circuit for which noise is not superimposed. *The EMC guard could be effective against electromagnetic noise caused by radiation, but against heavy electromagnetic noise (electromagnetic induction) and conductive noise from the power supply line for a fan, we recommend the use of an "anti-electrolytic corrosion fan" with ceramic bearing. e Pattern 1 Electric field/magnetic field of the high-frequency electricity Shielding metal Grounding to the cabinet Fan cabinet Propeller Pattern 2 High-frequency electricity is superimposed onto the power line for the fan. Metal cabinet of the equipment Return path of the high-frequency electricity Wind Mounting screw 314

308 Technical Material What is an EMC guard? It is a metallic piece that protects materials from the adverse effects of electromagnetic noise sources.it provides electromagnetic shielding. It is attached to the casing of a device by means of the fan fixing screw(s).ground the devices equipped with an EMC guard. EMC guard attached to a cooling fan EMC guard Fan EMC guards Dimensions(mm) Thickness(mm) Representative model numbers L17***5** 9GV57***5** E57***5** E17***5** 25 19E47***4** 9GL12***1** 38 9LB12***1** 12 9G12***1** 25 9G12***4** 19L9***4** P9***4** 32 19P8***2** 19L8***4** 25 19R8***4** 8 9A8***4** 2 19P8***6** 15 19P8***7** EMC:Electro Magnetic Compatibility, or a capability of a system when its performance is not affected by an electromagnetic environment. EMC guards takes effect in ordinary cases.you can choose from among EMC guards of different sizes. Example: We chose EMC guards because the electromagnetic noise emitted by our UPS, which induces current up to the fan, is not excessive. The ceramic material used for the bearing prevents current from flowing in it. Strong electromagnetic noise (electromagnetic induction) will not damage the bearing.so, we recommend the ceramic bearing for an environment with heavy electromagnetic noise. Operating precautions Storage temperature There is no performance problem when the system is used at between -3 and +7. There is a possibility that same problem of lubricant and insulation inside motor might occur by condensing due to rapid surrounding temperature change. Therefore, please take care of non-condensing using desiccant or something during fan is in storage. Handling precautions The fan motor is equipped with a precision ball bearing. Therefore, please handle the motors carefully in order not to shock the bearings. Recommended screw torque This shows the recommended values for the screw torque when installing the fans. If the tightening torque is higher than the recommended values, the fan can be deformed or damaged. Use care when tightening. Also, be sure to always use a fan with a ribbed structure when using screws to pass through and secure the fan. Fans :.44N m (4.5kgf cm) or less (with M3 screws) (Applies to fan motors of 52mm 52mm MAX.) Fans :.78N m (8kgf cm) or less (with M4 screws) (Applies to fan motors of 6mm 6mm MAX.) Fans :.98N m (1kgf cm) or less (with M4 screws) ( 2mm) Installation There are no limitations on the installation direction of fans or blowers. Fans have symbols on the fan indicating the airflow direction and blade rotation direction. When installing, use these symbols to check the airflow direction. Air Flow direction Discharge side Suction side Blade rotation direction Symbols indicating the fan airflow direction and blade rotation direction Comparison of ribbed and ribless structures Regarding plastic frame, we have a option ribbed and ribless about mounting. Please use preferred type up to your application. Please use ribbed fan in case that you hook fan up clamping either side fan mounting hole target. (According to the model, only models with or without ribs are available.) *Use a fan with a rib structure when using a screw for piercing. When securing screws to ribless plastic frame models, use a flange to secure on one side. Rib Ribbed Ribless Securing with flanges on both sides Securing with a flange on one side 315

309 Fan mounting using self-tapping screw Installing self-taping screws into the plastic frame of the fan may split or deform it. If you use self-tapping screws, use screws that are recommended by our company, and refer to our recommended screw torques and recommended pilot hole shapes. Pay close attention to the operating precautions and fully understand your equipment before you use it. [For nominal diameters of 4.8mm and 5mm] Self-tapping screw model No. SY-NS24812P15 SY-NS2512P Min. 12 Ø5.6 Plate Fan frame Minimum mounting plate thickness: T=1.2mm Self-tapping screw model No. SY-NS14812P15 SY-NS1512P15 Ø5.6 Plate Fan frame Fan mounting hole diameter [mm] Recommended screw torque [N m] Ribbed fan (Fig. A) Ø3.5 Ø4.3 Ø4.5.8 Max. Counter rotating fan (Fig. B) Ø3.5 Ø4.3.6 Max. Recommended self-tapping screws Material: Steel Plating: Trivalent chromating plating Fan mounting hole diameter Ø3.5 Ø4.3 Ø4.5 Fig. A: Ribbed fan Self-tapping screw model No. Nominal Length screw [L] diameter Fig. B: Counter rotating fan Head shape Unit: mm Flat-head/pan-head dimensions Head Height of Cross diameter head recess [D] [H] No. SY-NS2412P Flat Max. 2 SY-NS1412P Pan SY-NS24812P Flat Max. 2 SY-NS14812P Pan SY-NS2512P Flat Max. 2 SY-NS1512P Pan Operating precautions Place the self-tapping screw so that it is vertical and centered with the frame mounting hole (Fig. A) and then screw it in. The self-tapping screw could deform or split the frame if you screw it into the frame when the screw is not vertical. Screw in the self-tapping screw with the center of the mounting hole on the fan and the center of the pilot hole on the mounting plate aligned (Fig. B). Misaligned holes could lead to the frame being deformed or split. Vertically placed screw Fig. A Inclined screw Technical Material Head shape: Flat Head shape: Pan H 12 L L H Aligned and centered holes Fig. B Misaligned holes Recommended pilot hole shape [For nominal diameter 4mm] Self-tapping screw model No. SY-NS2412P Min. 12 Ø4.6 Plate Fan frame Minimum mounting plate thickness: T=1.2mm Self-tapping screw model No. SY-NS1412P11 Ø4.6 Plate Fan frame Never use self-tapping screws to mount a fan with a ribless frame (not including counter rotating fan). Tightening the screw beyond the recommended screw torque could deform or split the frame. With flat-head screws, failure to use the recommended pilot hole shape will cause interference between the flat-head screw and fan frame which could split the frame. Do not use self-tapping screws to mount the finger guard on the fan. Using self-tapping screws could deform or split the frame. Recommended screw manufacturer To purchase the screws, please contact the screw manufacturer directly. SAIMA CORPORATION Tsujido Fujisawa Kanagawa JAPAN TEL: FAX:

310 Technical Material Safety Precautions In order to ensure that this product is used safely, be sure that you read and understand the following precautions fully and use the product only as directed. Be sure to read these Safety Precautions carefully before installing, connecting, operating, maintaining, or inspecting this product. Follow all the precautions and directions given here. This product has been designed and manufactured for use as a device to be used in general industrial machinery, and may not be used as a standalone product. The product of our company (hereafter called the product) falls into the category of the products specified in the Attached List 1, Item 16 (Class 84, Item 14) of the Export Trade Control Ordinance. To export the product as an individual part or to export a product into which the product is assembled, the Information Requirements and Objective Requirements that the Ministry of Economy, Trade and Industry established based on the Catchall Controls must be studied for applicability. Based on information on applicability and specified requirements, appropriate export formalities must be performed. In order to prevent any possible bodily injury or damage to property or equipment, the following precautions for ensuring safety are displayed according to the following two ranks of importance: Danger Warning Handling or using the product improperly and in disregard of the instructions with this mark might result in serious bodily injury or death. Handling or using the product improperly and in disregard of the instructions with this mark might result in bodily injury or physical damage. Note: Items marked Warning might also result in serious bodily injury or death in some circumstances. Always follow the instructions for items marked Danger. Descriptions of the precautions to be taken to ensure safety are given below. 317 Danger If the product is used in medical appliances or other types of equipment that affect people s lives, sufficient safety-related evaluations and preparations must be made in advance, and the product or the type of equipment into which the product is assembled must be used on the user s own responsibility. If the product is used in types of equipment that have a strong social and public impact, sufficient prior evaluations and safety-related evaluations and preparations must be made, and the product or the type of equipment into which the product is assembled must be used on the user s own responsibility. If the product is used in an environment where there are vibrations, for example, in a car or aboard a ship, sufficient prior evaluations and safety-related evaluations and preparations must be made, and the product or the piece of equipment into which the product is assembled must be used on the user s own responsibility. Connect all wires properly and securely. Failure to do so might result in burns, fire, or exposure to electrical shock. If there are any grounding taps or wires, attach all grounds securely. Failure to do so might result in exposure to electrical shock. Never use in explosive atmosphere, as doing so might result in fires, burns, or bodily injury. Never operate with any live wires exposed, as doing so might result in electrical shock. Never allow any persons or objects to approach or come into contact with the rotor while in operation, as doing so might result in damage or personal injury. Turn off the power and stop using the product immediately if you notice any sparks, smoke, odd odors, sounds, or anything unusual during operation. Failure to do so might result in fi re, burns, or electrical shock. Never allow the product to fall, topple over, or otherwise be subjected to excessive shocks when moving it, as doing so might result in product breakdown or substandard operation. The product should be handled only by personnel with sufficient training and knowledge and under the responsibility of the end user. Never attempt to disassemble, repair, or alter this product in any way, as doing so might result in fire, burns, or electrical shock. Dispose of the product as industrial waste. Please contact your local government office for further details about disposal. Warning Handling Installation, placement, connections, wiring, or relocation of the product should be performed by knowledgeable or correctly licensed personnel. Never perform such work while the product is live as this might lead to injury, electrical shock, burns, or fire. Do not use the fan if not fi xed or stand in hand. Never allow yourself to come into contact with the ends of wires or plugs when measuring the insulation resistance or dielectric strength voltage. This might result in electrical shock. Never attempt to disassemble or alter this product in any way. Doing so might invalidate any warranties concerning the functions or performance of the product, and might also result in fi re, burns, bodily injury, or electrical shock. Instruction If the fan stops during operation, give proper consideration to the device for its protection. Never use the product at voltages, temperatures, or any other settings which exceed those given in the product specifications. This might result in substandard operation, breakdown, fire, bodily injury, or electrical shock. The fan may fail to operate properly if there is insufficient power capacity, because the starting current is several times larger than the rated current will flow at the moment of the voltage is supplied to the fan. Be sure to inquire about startup current levels for individual models. Do not control the speed of the fan by changing power voltage. It may cause fan failure. Start up all fans at the same possible timing if two or more fans which wind interferes with each other are installed in the device. If the fan is exposed to wind from other fans at start up, it may cause fan failure or the fan may not start up correctly. Never insert or remove any lead wires or connectors while the power is turned on. When inserting or removing plugs or connections, always be sure to first check that the power has been turned off and hold the housing of the plug or connector when doing so. Failure to do so might result in damage or exposure to electrical shock. Do not remove the lead wire from the frame hook. It may scratch and damage the surface of the lead wire. Never remove the product identification plate or install the product so that the identification cannot be seen after installation. This could result in the product being improperly used, and subsequently result in fi res. Do not push the nameplate of the DC fan with strong force. The nameplate may break and touch the shaft. The product might become damaged if foreign objects or external forces are allowed to interfere with normal fan operation. Do not implement ON-OFF of power supply in negative line. That might cause damage of the fan. Installation When fi xing this product into place, be sure to take into consideration the product s weight, the vibrations generated during operation, and all other relevant factors. Failure to do so might cause the product or parts of it to fall out of position, resulting in bodily injury or malfunction of the product. Be sure to check the direction of installation (i.e., the fan), as failing to do so might result in bodily injury or mechanical breakdown. In order to ensure that the product operates properly, allow spaces for ventilation and take whatever steps necessary to prevent the entry of foreign objects. Failure to do so might result in bodily injury or mechanical breakdown. When fi xing the fan with screws, make sure the screw and sheet metal do not deform the frame of the fan before operation. If the frame of the fan is deformed, mechanical failure may be occurred or specifi ed performance may not be generated. When fi xing the fan with screws, ensure the screwing torque. If the screwing torque is over the recommended screw torque, fan frame may be deformed or damaged. Use a ribbed frame when using screw for piercing. In order to prevent from loosing screw, please use plain washer and spring lock washer. For screwing torque of each fan type, contact SANYO DENKI or SANYO DENKI distributor. When fi xing the fan with self-tapping screws, fan frame may be damaged.

311 Warning When excessive shock is attacked to fan, impeller may be protruded from the surface of fan frame. Make sure that impeller does not touch cover such as finger guard and mounting plate. Do not give excessive shock to fan to avoid fan failure and deteriorate of fan performance. Pulling or pinching the lead wires could result in damage to the wire, and you should avoid placing excessive stresses on these wires. The device should also be installed so that the lead wires are not allowed to come into contact with the rotor or blades. Failure to do so might result in damage or exposure to electrical shock. Take proper precautions against static electricity when making electrical connections. Failure to do so might cause the breakdown of the fan or device. Install a fi nger guard or other cover if there is any danger of fingers, hands or objects coming into contact with the rotor or blades. Failure to do so might result in bodily injury or mechanical breakdown. Install the fi nger guard, fi lter, and plate to the fan in the correct position while avoiding touching of the rotor blade. Avoiding this will prevent device failure. Please use Sanyo Denki genuine finger guards and filter kits. Installation of Centrifugal Fan The fan shall be fi xed with screws. For screw size of each fan type, refer to drawing or catalog. Do not use the screws with length over the depth of mounting screw. Fan might not be fixed by damaging threaded hole. For depth of mounting screw of each fan type, refer to drawing or catalogue. When fi xing the fan with screws, ensure the screwing torque. If the screwing torque is over the recommended screw torque, threaded holes may be damaged. Also, in order to prevent from loosing screw, please use plain washer and spring lock washer. For screwing torque of each fan type, contact SANYO DENKI or SANYO DENKI distributor. When excessive shock is given to fan, impeller may be protruded. Make sure that impeller does not touch cover such as inlet nozzle and finger guard, and mounting plate. For positional relation among the fan, inlet nozzle, and plate of each fan type, refer to drawing or catalog. Install the inlet nozzle, fi nger guard, and plate to the fan in the correct position while avoiding touching of the rotor blade. Avoiding this will prevent device failure. Please use Sanyo Denki genuine inlet nozzle. Environment of usage The product must not be used or stored in a flammable or corrosive gas atmosphere, in a place where water or oil splashes (not applicable to Splash Proof or Oil Proof Fans), in a place where there is much dust or humidity, in a place where condensation occurs, in a place where the product is exposed to radioactive rays or is in direct sunlight, in a place where a salty sea breeze blows or seawater splashes, or in an environment where the product may be contaminated by such corrosive materials as sulfurous water, sulfurous volcanic ash, organic solvents, acidic chemicals, alkali chemicals, etc., such hazardous substances as nuclear fuel materials, etc. If it is used or stored in such places or environments, there is the possibility that a fire may occur, the product may malfunction or its performance may deteriorate. Avoid using or storing the product in locations and an environment where it could be constantly exposed to vibrations, strong shocks, magnetic or electromagnetic noise, and which the electromagnetic noise overlaps into power voltage. This might result in product breakdown or substandard operation. Avoid using or storing the product under environments where rapidly changed such as thermal and humidity change. This might result in product breakdown or deterioration. Maintenance Maintenance and inspections should always be performed by personnel with sufficient training and knowledge. Failure to do so might result in fire, burns, bodily injury, or electrical shock. Never perform any maintenance or inspections while the product is in operation. Also note that the blades continue to rotate for some time immediately after operation ceases. You should always be sure to check to see that all rotating parts have come to a stop before beginning work. Never use gasoline, paint thinner, benzene, or any other organic solvents to clean the product as this could result in the deformation or substandard operation. Technical Material 318

312 Index by Model No./Safety Standards List - Fans The category CPU refers to a CPU cooler. Model No. Category Frame Size UL CSA TÜV page Model No. Category Frame Size UL CSA TÜV page 19BC12FC7-1 Blower 52mm 15mm BC12GC7-1 Blower 52mm 15mm BC12HC7-1 Blower 52mm 15mm BC12MC7-1 Blower 52mm 15mm BC24FC7-1 Blower 52mm 15mm BC24GC7-1 Blower 52mm 15mm BC24HC7-1 Blower 52mm 15mm BD12FC2 Blower 76mm 3mm BD12HC2 Blower 76mm 3mm BD12MC2 Blower 76mm 3mm BD24FC2 Blower 76mm 3mm BD24HC2 Blower 76mm 3mm BD24MC2 Blower 76mm 3mm BF12HC2 Blower 12mm 32mm BF12MC2 Blower 12mm 32mm BF24HC2 Blower 12mm 32mm BF24MC2 Blower 12mm 32mm BG12HC1 Blower 16mm 4mm BG12MC1 Blower 16mm 4mm BG24HC1 Blower 16mm 4mm BG24MC1 Blower 16mm 4mm BJ12HC2 Blower 127mm 32mm BJ12MC2 Blower 127mm 32mm BJ24HC2 Blower 127mm 32mm BJ24MC2 Blower 127mm 32mm BM12GC2-1 Blower 97mm 33mm BM12HC2-1 Blower 97mm 33mm BM12MC2-1 Blower 97mm 33mm BM24GC2-1 Blower 97mm 33mm BM24HC2-1 Blower 97mm 33mm BM24MC2-1 Blower 97mm 33mm E1312A11 DC mm E1312S11 DC mm E1324A11 DC mm E1324G11 DC mm E1324S11 DC mm E1348A11 DC mm E1348G11 DC mm E1348S11 DC mm E1712F51 DC 172mm 51mm E1712H51 DC 172mm 51mm E1712K51 DC 172mm 51mm E1712M51 DC 172mm 51mm E1724C51 DC 172mm 51mm E1724H51 DC 172mm 51mm E1724K51 DC 172mm 51mm E1724M51 DC 172mm 51mm E1748C51 DC 172mm 51mm E1748H51 DC 172mm 51mm E1748K51 DC 172mm 51mm E1748M51 DC 172mm 51mm E224AS1 DC 2mm 7mm E224H1 DC 2mm 7mm E224MH1 DC 2mm 7mm E224S1 DC 2mm 7mm E4712L41 DC 172mm 147mm 25mm E4712M41 DC 172mm 147mm 25mm 157 Standard name Certification number UL E4681 CSA TÜV certification numbers differ by model. The contents of this catalog is as of September 212. Please ask us about new products that we released after September 212 if you want E4724F41 DC 172mm 147mm 25mm E4724H41 DC 172mm 147mm 25mm E4724L41 DC 172mm 147mm 25mm E4724M41 DC 172mm 147mm 25mm E4748F41 DC 172mm 147mm 25mm E4748H41 DC 172mm 147mm 25mm E4748L41 DC 172mm 147mm 25mm E4748M41 DC 172mm 147mm 25mm E4748S41 DC 172mm 147mm 25mm E5712F51 DC 172mm 15mm 51mm E5712H51 DC 172mm 15mm 51mm E5712K51 DC 172mm 15mm 51mm E5712M51 DC 172mm 15mm 51mm E5712Y51 DC 172mm 15mm 51mm E5724C51 DC 172mm 15mm 51mm E5724F51 DC 172mm 15mm 51mm E5724H51 DC 172mm 15mm 51mm E5724K51 DC 172mm 15mm 51mm E5724M51 DC 172mm 15mm 51mm E5748C51 DC 172mm 15mm 51mm E5748F51 DC 172mm 15mm 51mm E5748H51 DC 172mm 15mm 51mm E5748K51 DC 172mm 15mm 51mm E5748M51 DC 172mm 15mm 51mm L612F41 Long Life Fan mm L612G41 Long Life Fan mm L612H41 Long Life Fan mm L612M41 Long Life Fan mm L612S41 Long Life Fan mm L624D41 Long Life Fan mm L624F41 Long Life Fan mm L624H41 Long Life Fan mm L624M41 Long Life Fan mm L624S41 Long Life Fan mm L648G41 Long Life Fan mm L648H41 Long Life Fan mm L812F41 Long Life Fan mm L812H41 Long Life Fan mm L812L41 Long Life Fan mm L812M41 Long Life Fan mm L812S41 Long Life Fan mm L824F41 Long Life Fan mm L824H41 Long Life Fan mm L824L41 Long Life Fan mm L824M41 Long Life Fan mm L824S41 Long Life Fan mm L848H41 Long Life Fan mm L912F41 Long Life Fan mm L912H41 Long Life Fan mm L912L41 Long Life Fan mm L912M41 Long Life Fan mm L912S41 Long Life Fan mm L924F41 Long Life Fan mm L924H41 Long Life Fan mm L924L41 Long Life Fan mm L924M41 Long Life Fan mm L948C41 Long Life Fan mm L948H41 Long Life Fan mm L1412H11 Long Life Fan mm L1412M11 Long Life Fan mm L1424H11 Long Life Fan mm L1424M11 Long Life Fan mm L1448H11 Long Life Fan mm L1448M11 Long Life Fan mm L1712H51 Long Life Fan 172mm 51mm L1712M51 Long Life Fan 172mm 51mm 271

313 Model No. Category Frame Size UL CSA TÜV page Model No. Category Frame Size UL CSA TÜV page 19L1724H51 Long Life Fan 172mm 51mm L1724M51 Long Life Fan 172mm 51mm L1748H51 Long Life Fan 172mm 51mm L1748M51 Long Life Fan 172mm 51mm L5712H51 Long Life Fan 172mm 15mm 51mm L5712M51 Long Life Fan 172mm 15mm 51mm L5724H51 Long Life Fan 172mm 15mm 51mm L5724M51 Long Life Fan 172mm 15mm 51mm L5748H51 Long Life Fan 172mm 15mm 51mm L5748M51 Long Life Fan 172mm 15mm 51mm P45F313 DC mm 75 19P45F61 DC 4 4 2mm 67 19P45H313 DC mm 75 19P45H61 DC 4 4 2mm 67 19P45H71 DC mm 65 19P45H91 DC 4 4 1mm 63 19P45J61 DC 4 4 2mm 67 19P45M61 DC 4 4 2mm 67 19P45M71 DC mm 65 19P45M91 DC 4 4 1mm 63 19P412B313 DC mm 75 19P412D61 DC 4 4 2mm 67 19P412E61 DC 4 4 2mm 67 19P412F313 DC mm 75 19P412F61 DC 4 4 2mm 67 19P412G313 DC mm 75 19P412G61 DC 4 4 2mm 67 19P412H313 DC mm 75 19P412H61 DC 4 4 2mm 67 19P412H71 DC mm 65 19P412H91 DC 4 4 1mm 63 19P412J313 DC mm 75 19P412K313 DC mm 75 19P412M313 DC mm 75 19P412M61 DC 4 4 2mm 67 19P412M71 DC mm 65 19P412M91 DC 4 4 1mm 63 19P412R71 DC mm 65 19P412S71 DC mm 65 19P424B313 DC mm 75 19P424B61 DC 4 4 2mm 67 19P424D61 DC 4 4 2mm 67 19P424F313 DC mm 75 19P424F61 DC 4 4 2mm 67 19P424G313 DC mm 75 19P424H313 DC mm 75 19P424H61 DC 4 4 2mm 67 19P424H71 DC mm 65 19P424J313 DC mm 75 19P55M71 DC mm 79 19P512A71 DC mm 79 19P512H71 DC mm 79 19P512M71 DC mm 79 19P524A71 DC mm 79 19P524H71 DC mm 79 19P524M71 DC mm 79 19P65H71 DC mm 81 19P65M71 DC mm 81 19P612B71 DC mm 81 19P612H61 DC 6 6 2mm 83 19P612H71 DC mm 81 19P612K71 DC mm 81 19P612M61 DC 6 6 2mm 83 19P612M71 DC mm 81 19P612S71 DC mm 81 19P612W61 DC 6 6 2mm 83 19P624H61 DC 6 6 2mm 83 19P624H71 DC mm 81 19P624J71 DC mm 81 19P624M61 DC 6 6 2mm 83 19P624M71 DC mm 81 19P624S71 DC mm 81 19P624W61 DC 6 6 2mm 83 19P648H61 DC 6 6 2mm 83 19P812A21(211) DC mm P812C61 DC 8 8 2mm 11 19P812H21(211) DC mm P812H61 DC 8 8 2mm 11 19P812H71 DC mm 99 19P812M21(211) DC mm P812M61 DC 8 8 2mm 11 19P812M71 DC mm 99 19P824A21(211) DC mm P824H21(211) DC mm P824H61 DC 8 8 2mm 11 19P824H71 DC mm 99 19P824M21(211) DC mm P824M61 DC 8 8 2mm 11 19P824M71 DC mm 99 19P848C61 DC 8 8 2mm 11 19P848H21(211) DC mm P848H61 DC 8 8 2mm 11 19P912F41(411) DC mm P912H41(411) DC mm P912J41(411) DC mm P912L41(411) DC mm P912M41(411) DC mm P912W41(411) DC mm P924F41(411) DC mm P924H41(411) DC mm P924J41(411) DC mm P924L41(411) DC mm P924M41(411) DC mm P924W41(411) DC mm P948H41(411) DC mm P1312H11(111) DC mm P1312S11(111) DC mm P1324H11(111) DC mm P1324S11(111) DC mm P1348H11(111) DC mm P1348S11(111) DC mm P1412H11 DC mm P1412M11 DC mm P1424H11 DC mm P1424M11 DC mm P1448H11 DC mm P1448M11 DC mm R65F41(411) DC mm 87 19R65H41(411) DC mm 87 19R65M41(411) DC mm 87 19R612D41(411) DC mm 87 19R612F41(411) DC mm 87 19R612G41(411) DC mm 87 19R612H41(411) DC mm 87 19R612J41(411) DC mm 87 19R612M41(411) DC mm 87 19R612S41(411) DC mm 87 19R624D41(411) DC mm 87 19R624F41(411) DC mm 87 19R624G41(411) DC mm 87 19R624H41(411) DC mm 87 19R624J41(411) DC mm Index by Model No./Safety Standards List

314 Index by Model No./Safety Standards List - Fans Model No. Category Frame Size UL CSA TÜV page Model No. Category Frame Size UL CSA TÜV page 19R624M41(411) DC mm 87 19R624S41(411) DC mm 87 19R648G41(411) DC mm 87 19R648H41(411) DC mm 87 19R648J41(411) DC mm 87 19R85F41(411) DC mm 17 19R85M41(411) DC mm 17 19R812E41(411) DC mm 17 19R812F41(411) DC mm 17 19R812G41(411) DC mm 17 19R812H41(411) DC mm 17 19R812L41(411) DC mm 17 19R812M41(411) DC mm 17 19R812S41(411) DC mm 17 19R824F41(411) DC mm 17 19R824G41(411) DC mm 17 19R824H41(411) DC mm 17 19R824L41(411) DC mm 17 19R824M41(411) DC mm 17 19R824S41(411) DC mm 17 19R848K41(411) DC mm 17 19R848S41(411) DC mm 17 19W1412H11-U Splash Proof Fan mm W1412M11-U Splash Proof Fan mm W1424H11-U Splash Proof Fan mm W1424M11-U Splash Proof Fan mm W1448H11-U Splash Proof Fan mm W1448M11-U Splash Proof Fan mm X9112PTH16 CPU 9mm X9212PTH16 CPU 9mm 298 9A612F41(411) DC mm 91 9A612G41(411) DC mm 91 9A612H41(411) DC mm 91 9A612M41(411) DC mm 91 9A612S41(411) DC mm 91 9A624F41(411) DC mm 91 9A624G41(411) DC mm 91 9A624H41(411) DC mm 91 9A624M41(411) DC mm 91 9A624S41(411) DC mm 91 9A812F41(411) DC mm 111 9A812G41(411) DC mm 111 9A812H41(411) DC mm 111 9A812L41(411) DC mm 111 9A812M41(411) DC mm 111 9A812S41(411) DC mm 111 9A824F41(411) DC mm 111 9A824G41(411) DC mm 111 9A824H41(411) DC mm 111 9A824L41(411) DC mm 111 9A824M41(411) DC mm 111 9A824S41(411) DC mm 111 9A912F41(411) DC mm 123 9A912G41(411) DC mm 123 9A912H41(411) DC mm 123 9A912L41(411) DC mm 123 9A912M41(411) DC mm 123 9A912S41(411) DC mm 123 9A924F41(411) DC mm 123 9A924G41(411) DC mm 123 9A924H41(411) DC mm 123 9A924L41(411) DC mm 123 9A924M41(411) DC mm 123 9A924S41(411) DC mm 123 9BD12FC6-1 Blower 76mm 2mm 283 9BD12HC6-1 Blower 76mm 2mm BD12SC6-1 Blower 76mm 2mm 283 9BD24FC6-1 Blower 76mm 2mm 283 9BD24HC6-1 Blower 76mm 2mm 283 9BD24SC6-1 Blower 76mm 2mm 283 9BFB12P2H3 Blower 12mm 32mm 293 9BFB24P2H3 Blower 12mm 32mm 293 9BMB12F21 Blower 97mm 33mm 289 9BMB12G21 Blower 97mm 33mm 289 9BMB12H21 Blower 97mm 33mm 289 9BMB12P2F1 Blower 97mm 33mm 289 9BMB12P2K1 Blower 97mm 33mm 289 9BMB12S21 Blower 97mm 33mm 289 9BMB24F21 Blower 97mm 33mm 289 9BMB24G21 Blower 97mm 33mm 289 9BMB24H21 Blower 97mm 33mm 289 9BMB24P2G1 Blower 97mm 33mm 289 9BMB24P2K1 Blower 97mm 33mm 289 9BMB24S21 Blower 97mm 33mm 289 9CR612H1 Counter Rotating Fan mm 191 9CR612P5G3 Counter Rotating Fan mm 187 9CR612P5H3 Counter Rotating Fan mm 187 9CR612S1 Counter Rotating Fan mm 191 9CR812H81 Counter Rotating Fan 8 8 8mm 195 9CR812S81 Counter Rotating Fan 8 8 8mm 195 9CR1212PG3 Counter Rotating Fan mm 197 9CR5748P9G1 Counter Rotating Fan 172mm 15mm 12mm 199 9CRA312P4J3 Counter Rotating Fan mm 171 9CRA312P4K3 Counter Rotating Fan mm 171 9CRA412G51 Counter Rotating Fan mm 185 9CRA412J51 Counter Rotating Fan mm 185 9CRA412K51 Counter Rotating Fan mm 185 9CRA412P4G3 Counter Rotating Fan mm 173 9CRA412P4J3 Counter Rotating Fan mm 173 9CRA412P4K3 Counter Rotating Fan mm 173 9CRA612PG1 Counter Rotating Fan mm 189 9CRA612PS1 Counter Rotating Fan mm 189 9CRA812P8G1 Counter Rotating Fan 8 8 8mm 193 9CRA848P8G1 Counter Rotating Fan 8 8 8mm 193 9CRB412P5J21 Counter Rotating Fan mm 175 9CRB412P5K1 Counter Rotating Fan mm 175 9CRD412P5G3 Counter Rotating Fan mm 179 9CRD412P5H3 Counter Rotating Fan mm 179 9CRD412P5J3 Counter Rotating Fan mm 179 9CRD412P5M3 Counter Rotating Fan mm 179 9CRE412P5J3 Counter Rotating Fan mm 183 9CRF412P5K21 Counter Rotating Fan mm 177 9EC224H1 DC 2mm 7mm 169 9EC248A1 DC 2mm 7mm 169 9EC248H1 DC 2mm 7mm 169 9G612G11(111) DC mm 97 9G612P4H1(11) DC mm 85 9G612P4S1(11) DC mm 85 9G612S11(111) DC mm 97 9G624G11(111) DC mm 97 9G624H11(111) DC mm 97 9G624P4H1(11) DC mm 85 9G624P4S1(11) DC mm 85 9G624S11(111) DC mm 97 9G648G11(111) DC mm 97 9G648P4S1(11) DC mm 85 9G648S11(111) DC mm 97 9G812G11(111) DC mm 119 9G812H11(111) DC mm 119 9G812K11(111) DC mm 119 9G824G11(111) DC mm 119 9G824H11(111) DC mm 119

315 Model No. Category Frame Size UL CSA TÜV page Model No. Category Frame Size UL CSA TÜV page 9G848G11(111) DC mm 119 9G848H11(111) DC mm 119 9G912A21(211) DC mm 125 9G912G11(111) DC mm 129 9G912H11(111) DC mm 129 9G912H21(211) DC mm 125 9G912M21(211) DC mm 125 9G912S21(211) DC mm 125 9G924A21(211) DC mm 125 9G924G11(111) DC mm 129 9G924H11(111) DC mm 129 9G924H21(211) DC mm 125 9G924M21(211) DC mm 125 9G924S21(211) DC mm 125 9G948A21(211) DC mm 125 9G948G11(111) DC mm 129 9G948H11(111) DC mm 129 9G948H21(211) DC mm 125 9G948M21(211) DC mm 125 9G948S21(211) DC mm 125 9G1212A41(411) DC mm 135 9G1212B41(411) DC mm 135 9G1212E11(111) DC mm 143 9G1212E41(411) DC mm 135 9G1212F11(111) DC mm 143 9G1212F41(411) DC mm 135 9G1212G11(111) DC mm 143 9G1212G41(411) DC mm 135 9G1212H11(111) DC mm 143 9G1212H41(411) DC mm 135 9G1212M11(111) DC mm 143 9G1212M41(411) DC mm 135 9G1224A41(411) DC mm 135 9G1224E11(111) DC mm 143 9G1224E41(411) DC mm 135 9G1224F11(111) DC mm 143 9G1224F41(411) DC mm 135 9G1224G11(111) DC mm 143 9G1224G41(411) DC mm 135 9G1224H11(111) DC mm 143 9G1224H41(411) DC mm 135 9G1224M11(111) DC mm 143 9G1224M41(411) DC mm 135 9G1248A41(411) DC mm 135 9G1248E11(111) DC mm 143 9G1248E41(411) DC mm 135 9G1248F11(111) DC mm 143 9G1248F41(411) DC mm 135 9G1248G11(111) DC mm 143 9G1248G41(411) DC mm 135 9G1248H11(111) DC mm 143 9G1248H41(411) DC mm 135 9G1248M11(111) DC mm 143 9G1248M41(411) DC mm 135 9GA45P6F1 Low Power Consumption Fan 4 4 2mm 13 9GA45P6H1 Low Power Consumption Fan 4 4 2mm 13 9GA412G71 Low Power Consumption Fan mm 11 9GA412H71 Low Power Consumption Fan mm 11 9GA412P3G1(11) Low Power Consumption Fan mm 17 9GA412P3H1(11) Low Power Consumption Fan mm 17 9GA412P3J1(11) Low Power Consumption Fan mm 17 9GA412P3K1(11) Low Power Consumption Fan mm 17 9GA412P3M1(11) Low Power Consumption Fan mm 17 9GA412P6F1 Low Power Consumption Fan 4 4 2mm 13 9GA412P6G1 Low Power Consumption Fan 4 4 2mm 13 9GA412P6H1 Low Power Consumption Fan 4 4 2mm 13 9GA412P7G1 Low Power Consumption Fan mm 11 9GA424P6F1 Low Power Consumption Fan 4 4 2mm 13 9GA424P6G1 Low Power Consumption Fan 4 4 2mm 13 9GA424P6H1 Low Power Consumption Fan 4 4 2mm 13 9GA512P7A1 Low Power Consumption Fan mm 21 9GA512P7G1 Low Power Consumption Fan mm 21 9GA512P7H1 Low Power Consumption Fan mm 21 9GA512P7M1 Low Power Consumption Fan mm 21 9GA524P7A1 Low Power Consumption Fan mm 21 9GA524P7G1 Low Power Consumption Fan mm 21 9GA524P7H1 Low Power Consumption Fan mm 21 9GA524P7M1 Low Power Consumption Fan mm 21 9GA612H61 Low Power Consumption Fan 6 6 2mm 29 9GA612L71 Low Power Consumption Fan mm 25 9GA612M61 Low Power Consumption Fan 6 6 2mm 29 9GA612M71 Low Power Consumption Fan mm 25 9GA612P1H3(31) Low Power Consumption Fan mm 33 9GA612P1J3(31) Low Power Consumption Fan mm 33 9GA612P1K3(31) Low Power Consumption Fan mm 33 9GA612P1K6(61) Low Power Consumption Fan mm 33 9GA612P6G1 Low Power Consumption Fan 6 6 2mm 29 9GA612P6S1 Low Power Consumption Fan 6 6 2mm 29 9GA612P7G1 Low Power Consumption Fan mm 25 9GA612P7H1 Low Power Consumption Fan mm 25 9GA624H61 Low Power Consumption Fan 6 6 2mm 29 9GA624M61 Low Power Consumption Fan 6 6 2mm 29 9GA624P1J3(31) Low Power Consumption Fan mm 33 9GA624P6G1 Low Power Consumption Fan 6 6 2mm 29 9GA624P6S1 Low Power Consumption Fan 6 6 2mm 29 9GA812P1H61(611) Low Power Consumption Fan mm 41 9GA812P1S61(611) Low Power Consumption Fan mm 41 9GA812P2H1(11) Low Power Consumption Fan mm 39 9GA812P2M1(11) Low Power Consumption Fan mm 39 9GA812P2S1(11) Low Power Consumption Fan mm 39 9GA812P6G1 Low Power Consumption Fan 8 8 2mm 37 9GA812P6M1 Low Power Consumption Fan 8 8 2mm 37 9GA824P1H61(611) Low Power Consumption Fan mm 41 9GA824P1S61(611) Low Power Consumption Fan mm 41 9GA824P2S1(11) Low Power Consumption Fan mm 39 9GA824P6G1 Low Power Consumption Fan 8 8 2mm 37 9GA824P6M1 Low Power Consumption Fan 8 8 2mm 37 9GA912P1H3(31) Low Power Consumption Fan mm 49 9GA912P4G3(31) Low Power Consumption Fan mm 45 9GA912P4J3(31) Low Power Consumption Fan mm 45 9GA912P4S3(31) Low Power Consumption Fan mm 45 9GA924P4G3(31) Low Power Consumption Fan mm 45 9GA924P4J3(31) Low Power Consumption Fan mm 45 9GA924P4S3(31) Low Power Consumption Fan mm 45 9GA948P1H3 Low Power Consumption Fan mm 49 9GE412P3G3 DC mm 71 9GE412P3J3 DC mm 71 9GE412P3K3 DC mm 71 9GL1212E11 Long Life Fan mm 261 9GL1212F11 Long Life Fan mm 261 9GL1212G11 Long Life Fan mm 261 9GL1212H11 Long Life Fan mm 261 9GL1212M11 Long Life Fan mm 261 9GL1224E11 Long Life Fan mm 261 9GL1224F11 Long Life Fan mm 261 9GL1224G11 Long Life Fan mm 261 9GL1224H11 Long Life Fan mm 261 9GL1224M11 Long Life Fan mm 261 9GL1248E11 Long Life Fan mm 261 9GL1248F11 Long Life Fan mm 261 9GL1248G11 Long Life Fan mm 261 9GL1248H11 Long Life Fan mm Index by Model No./Safety Standards List

316 Index by Model No./Safety Standards List - Fans Model No. Category Frame Size UL CSA TÜV page Model No. Category Frame Size UL CSA TÜV page 9GL1248M11 Long Life Fan mm 261 9GV312E31(311) DC mm 61 9GV312G31(311) DC mm 61 9GV312H31(311) DC mm 61 9GV312J31(311) DC mm 61 9GV312K31(311) DC mm 61 9GV412C31(311) DC mm 73 9GV412G31(311) DC mm 73 9GV412J31(311) DC mm 73 9GV412K31(311) DC mm 73 9GV612P1G3(31) DC mm 93 9GV612P1H3(31) DC mm 93 9GV612P1L1(11) DC mm 93 9GV612P1M3(31) DC mm 93 9GV624P1G3(31) DC mm 93 9GV648P1H3(31) DC mm 93 9GV812P1F3(31) DC mm 115 9GV812P1G3(31) DC mm 115 9GV812P1H3(31) DC mm 115 9GV812P1M3(31) DC mm 115 9GV812P4J3(31) DC mm 13 9GV812P4K3(31) DC mm 13 9GV824P1G3(31) DC mm 115 9GV824P4K1(11) DC mm 13 9GV848P1G3(31) DC mm 115 9GV848P4K3(31) DC mm 13 9GV912P1G3(31) DC mm 127 9GV912P1H3(31) DC mm 127 9GV948P1H3(31) DC mm 127 9GV1212P1J1(11) DC mm 139 9GV1212P4G1(11) DC mm 131 9GV1224P1H1(11) DC mm 139 9GV1224P1J1(11) DC mm 139 9GV1224P4G1(11) DC mm 131 9GV1248P1J1(11) DC mm 139 9GV1248P4G1(11) DC mm 131 9GV1248P4H1(11) DC mm 131 9GV1248P4J1(11) DC mm 131 9GV1512H51(511) DC mm 155 9GV1512M51(511) DC mm 155 9GV1524M51(511) DC mm 155 9GV3612G31 DC mm 59 9GV3612J31 DC mm 59 9GV5724H51 DC 172mm 15mm 51mm 161 9GV5748H51 DC 172mm 15mm 51mm 161 9L412H31 Long Life Fan mm 251 9L412J31 Long Life Fan mm 251 9L412M31 Long Life Fan mm 251 9LB1212H11 Long Life Fan mm 259 9LB1212M11 Long Life Fan mm 259 9LB1224H11 Long Life Fan mm 259 9LB1224M11 Long Life Fan mm 259 9LB1224S11 Long Life Fan mm 259 9LB1248H11 Long Life Fan mm 259 9LB1248M11 Long Life Fan mm 259 9LB1412H51 Long Life Fan mm 267 9LB1412M51 Long Life Fan mm 267 9LB1412S51 Long Life Fan mm 267 9LB1424B51 Long Life Fan mm 267 9LB1424H51 Long Life Fan mm 267 9LB1424M51 Long Life Fan mm 267 9LB1424S51 Long Life Fan mm 267 9LB1448F51 Long Life Fan mm 267 9LB1448H51 Long Life Fan mm 267 9LB1448M51 Long Life Fan mm 267 9LB1448S51 Long Life Fan mm S612F41(411) Silent Fan mm 51 9S612H41(411) Silent Fan mm 51 9S612M41(411) Silent Fan mm 51 9S612S41(411) Silent Fan mm 51 9S812F41(411) Silent Fan mm 53 9S812H41(411) Silent Fan mm 53 9S812L41(411) Silent Fan mm 53 9S812M41(411) Silent Fan mm 53 9S824L41(411) Silent Fan mm 53 9S824M41(411) Silent Fan mm 53 9S912F41(411) Silent Fan mm 55 9S912L41(411) Silent Fan mm 55 9S912M41(411) Silent Fan mm 55 9S924F41(411) Silent Fan mm 55 9S924L41(411) Silent Fan mm 55 9S924M41(411) Silent Fan mm 55 9S1212F41(411) Silent Fan mm 57 9S1212H41(411) Silent Fan mm 57 9S1212L41(411) Silent Fan mm 57 9S1212M41(411) Silent Fan mm 57 9SG1212G11 DC mm 147 9SG1224G11 DC mm 147 9SG1224H11 DC mm 147 9SG1248G11 DC mm 147 9SG5724P5H61 DC 172mm 15mm 51mm 159 9SG5748P5G1 DC 172mm 15mm 51mm 159 9SG5748P5H1 DC 172mm 15mm 51mm 159 9TG24PG1 Centrifugal Fan 175mm 69mm 279 9TG48PG1 Centrifugal Fan 175mm 69mm 279 9TJ24PH61 Centrifugal Fan 133mm 91mm 275 9TJ48PH1 Centrifugal Fan 133mm 91mm 275 9TM48P4H1 Centrifugal Fan 1mm 25mm 273 9TN24P1H1 Centrifugal Fan 15mm 35mm 277 9TN48P1H1 Centrifugal Fan 15mm 35mm 277 9W1TG48PH61 Splash Proof Centrifugal Fan 175mm 69mm 237 9W1TJ48PH61 Splash Proof Centrifugal Fan 133mm 91mm 233 9W1TM48P4G1 Splash Proof Centrifugal Fan 1mm 25mm 231 9W1TM48P4H1 Splash Proof Centrifugal Fan 1mm 25mm 231 9W1TN48P1H1 Splash Proof Centrifugal Fan 15mm 35mm 235 9WB1412H51 Splash Proof Fan mm 225 9WB1412M51 Splash Proof Fan mm 225 9WB1412S51 Splash Proof Fan mm 225 9WB1424H51 Splash Proof Fan mm 225 9WB1424M51 Splash Proof Fan mm 225 9WB1448H51 Splash Proof Fan mm 225 9WB1448S51 Splash Proof Fan mm 225 9WE1724K51 Splash Proof Fan 172mm 51mm 23 9WE5724K51 Splash Proof Fan 172mm 15mm 51mm 229 9WE5748K51 Splash Proof Fan 172mm 15mm 51mm 229 9WF424F61 Oil Proof Fan 4 4 2mm 24 9WF424H61 Oil Proof Fan 4 4 2mm 24 9WF424H71 Oil Proof Fan mm 239 9WF624H41 Oil Proof Fan mm 243 9WF624H61 Oil Proof Fan 6 6 2mm 242 9WF624H71 Oil Proof Fan mm 241 9WF824S41 Oil Proof Fan mm 244 9WF924H21 Oil Proof Fan mm 247 9WF924H41 Oil Proof Fan mm 245 9WF924S21 Oil Proof Fan mm 247 9WF1224H11 Oil Proof Fan mm 249 9WG1212E11-E Splash Proof Fan mm 219 9WG1212F11-E Splash Proof Fan mm 219 9WG1212G11-E Splash Proof Fan mm 219 9WG1212H11-E Splash Proof Fan mm 219 9WG1212M11-E Splash Proof Fan mm 219 9WG1224E11-E Splash Proof Fan mm 219

317 Model No. Category Frame Size UL CSA TÜV page 9WG1224F11-E Splash Proof Fan mm 219 9WG1224G11-E Splash Proof Fan mm 219 9WG1224H11-E Splash Proof Fan mm 219 9WG1224M11-E Splash Proof Fan mm 219 9WG1248E11-E Splash Proof Fan mm 219 9WG1248F11-E Splash Proof Fan mm 219 9WG1248G11-E Splash Proof Fan mm 219 9WG1248H11-E Splash Proof Fan mm 219 9WG1248M11-E Splash Proof Fan mm 219 9WG5748P5G1 Splash Proof Fan 172mm 15mm 51mm 227 9WG5748P5H1 Splash Proof Fan 172mm 15mm 51mm 227 9WP612G41(411) Splash Proof Fan mm 21 9WP612H41(411) Splash Proof Fan mm 21 9WP624H41(411) Splash Proof Fan mm 21 9WP648H41(411) Splash Proof Fan mm 21 9WP812G41(411) Splash Proof Fan mm 23 9WP812H41(411) Splash Proof Fan mm 23 9WP824H41(411) Splash Proof Fan mm 23 9WP848S41(411) Splash Proof Fan mm 23 9WP912F41 Splash Proof Fan mm 211 9WP924B41 Splash Proof Fan mm 211 9WP924F41 Splash Proof Fan mm 211 9WP924H41 Splash Proof Fan mm 211 9WP924S41 Splash Proof Fan mm 211 9WP1212H11(111) Splash Proof Fan mm 217 9WP1224H11(111) Splash Proof Fan mm 217 9WP1248H11(111) Splash Proof Fan mm 217 9WS812F41(411) Splash Proof Fan mm 25 9WS812H41(411) Splash Proof Fan mm 25 9WS812M41(411) Splash Proof Fan mm 25 9WS824F41(411) Splash Proof Fan mm 25 9WS824H41(411) Splash Proof Fan mm 25 9WS824M41(411) Splash Proof Fan mm 25 9WS912F41 Splash Proof Fan mm 29 9WS912H41 Splash Proof Fan mm 29 9WS912L41 Splash Proof Fan mm 29 9WS912M41 Splash Proof Fan mm 29 9WS924F41 Splash Proof Fan mm 29 9WS924H41 Splash Proof Fan mm 29 9WS924L41 Splash Proof Fan mm 29 9WS924M41 Splash Proof Fan mm 29 9WS1212H11(111) Splash Proof Fan mm 221 9WS1212M11(111) Splash Proof Fan mm 221 9WS1224H11(111) Splash Proof Fan mm 221 9WS1224M11(111) Splash Proof Fan mm 221 9WS1248H11(111) Splash Proof Fan mm 221 9WS1248M11(111) Splash Proof Fan mm 221 9WV848P1H1(11) Splash Proof Fan mm 27 9WV948P1H1 Splash Proof Fan mm 213 9WV1224P1H1 Splash Proof Fan mm 215 9WV1248P1J1 Splash Proof Fan mm 215 Index by Model No. - Options Model No. Category Matching Fan Size page 19-19C Finger guards 12mm sq. type E Finger guards 12mm sq. type H Finger guards 12mm sq. type K Finger guards 12mm sq. type C Finger guards 8mm sq. type E Finger guards 8mm sq. type H Finger guards 8mm sq. type Finger guards 4mm sq. type C Finger guards 92mm sq. type E Finger guards 92mm sq. type H Finger guards 92mm sq. type F13 Resin filter kits 12mm sq. type F2 Resin filter kits 12mm sq. type F3 Resin filter kits 12mm sq. type F4 Resin filter kits 12mm sq. type G Resin Finger guards 12mm sq. type F13 Resin filter kits 92mm sq. type F2 Resin filter kits 92mm sq. type F3 Resin filter kits 92mm sq. type F4 Resin filter kits 92mm sq. type G Resin Finger guards 92mm sq. type F13 Resin filter kits 8mm sq. type F2 Resin filter kits 8mm sq. type F3 Resin filter kits 8mm sq. type F4 Resin filter kits 8mm sq. type G Resin Finger guards 8mm sq. type F13 Resin filter kits 6mm sq. type F2 Resin filter kits 6mm sq. type F3 Resin filter kits 6mm sq. type F4 Resin filter kits 6mm sq. type G Resin Finger guards 6mm sq. type EMC guards 172mm type EMC guards 12mm sq. type EMC guards 8mm sq. type EMC guards 8mm sq. type EMC guards 92mm sq. type Finger guards 36mm sq. type Finger guards 15mm sq. type Finger guards 15mm sq. type Finger guards 38mm sq. type Finger guards 172mm type Finger guards 172mm type Inlet nozzle for centrifugal fan and splash proof centrifugal fan 133mm type Inlet nozzle for centrifugal fan and splash proof centrifugal fan 175mm type Inlet nozzle for centrifugal fan and splash proof centrifugal fan 1mm type Inlet nozzle for centrifugal fan and splash proof centrifugal fan 15mm type Finger guards 15mm type Finger guards 133mm type E Finger guards 6mm sq. type H Finger guards 6mm sq. type Finger guards 52mm sq. type E Finger guards 52mm sq. type E Finger guards 172mm type H Finger guards 172mm type J Finger guards 172mm type Finger guards 172mm type Finger guards 14mm sq. type H Finger guards 14mm sq. type Finger guards 2mm type H Finger guards 2mm type Finger guards 2mm type H Finger guards 2mm type Finger guards 127mm sq. type Finger guards 127mm sq. type 32 Recommended connectors for DC fans 36p Thermistor 36p IC L873 for DC fan sensor 36p 324 Index by Model No./Safety Standards List

318 Index by Frame Size/Safety Standards List - Axial Fan Frame Size Category Model No. UL CSA TÜV page Frame Size Category Model No. UL CSA TÜV page mm DC 9GV312H31(311) mm DC 9GV312K31(311) mm DC 9GV3612G mm DC 9GV3612J mm DC 9GV312E31(311) mm DC 9GV312G31(311) mm DC 9GV312J31(311) mm Counter Rotating Fan 9CRA312P4J mm Counter Rotating Fan 9CRA312P4K mm DC 19P45H mm DC 19P45M mm DC 19P412H mm DC 19P412M mm DC 19P45H mm DC 19P45M mm DC 19P412H mm DC 19P412M mm DC 19P412R mm DC 19P412S mm DC 19P424H mm Counter Rotating Fan 9GA412G mm Counter Rotating Fan 9GA412H mm Counter Rotating Fan 9GA412P7G mm Oil Proof Fan 9WF424H mm DC 19P45F mm DC 19P45H mm DC 19P45J mm DC 19P45M mm DC 19P412D mm DC 19P412E mm DC 19P412F mm DC 19P412G mm DC 19P412H mm DC 19P412M mm DC 19P424B mm DC 19P424D mm DC 19P424F mm DC 19P424H mm Low Power Consumption Fan 9GA45P6F mm Low Power Consumption Fan 9GA45P6H mm Low Power Consumption Fan 9GA412P6F mm Low Power Consumption Fan 9GA412P6G mm Low Power Consumption Fan 9GA412P6H mm Low Power Consumption Fan 9GA424P6F mm Low Power Consumption Fan 9GA424P6G mm Low Power Consumption Fan 9GA424P6H mm Oil Proof Fan 9WF424F mm Oil Proof Fan 9WF424H mm DC 19P45F mm DC 19P45H mm DC 19P412B mm DC 19P412F mm DC 19P412G mm DC 19P412H mm DC 19P412J mm DC 19P412K mm DC 19P412M Standard name Certification number UL E4681 CSA TÜV certification numbers differ by model. The contents of this catalog is as of September 212. Please ask us about new products that we released after September 212 if you want mm DC 19P424B mm DC 19P424F mm DC 19P424G mm DC 19P424H mm DC 19P424J mm DC 9GE412P3G mm DC 9GE412P3J mm DC 9GE412P3K mm DC 9GV412C31(311) mm DC 9GV412G31(311) mm DC 9GV412J31(311) mm DC 9GV412K31(311) mm Long Life Fan 9L412H mm Long Life Fan 9L412J mm Long Life Fan 9L412M mm Low Power Consumption Fan 9GA412P3G1(11) mm Low Power Consumption Fan 9GA412P3H1(11) mm Low Power Consumption Fan 9GA412P3K1(11) mm Low Power Consumption Fan 9GA412P3J mm Low Power Consumption Fan 9GA412P3M mm Counter Rotating Fan 9CRA412P4G mm Counter Rotating Fan 9CRA412P4J mm Counter Rotating Fan 9CRA412P4K mm Counter Rotating Fan 9CRB412P5J mm Counter Rotating Fan 9CRB412P5K mm Counter Rotating Fan 9CRF412P5K mm Counter Rotating Fan 9CRA412G mm Counter Rotating Fan 9CRA412J mm Counter Rotating Fan 9CRA412K mm Counter Rotating Fan 9CRD412P5G mm Counter Rotating Fan 9CRD412P5H mm Counter Rotating Fan 9CRD412P5J mm Counter Rotating Fan 9CRD412P5M mm Counter Rotating Fan 9CRE412P5J mm DC 19P55M mm DC 19P512A mm DC 19P512H mm DC 19P512M mm DC 19P524A mm DC 19P524H mm DC 19P524M mm Low Power Consumption Fan 9GA512P7A mm Low Power Consumption Fan 9GA512P7G mm Low Power Consumption Fan 9GA512P7H mm Low Power Consumption Fan 9GA512P7M mm Low Power Consumption Fan 9GA524P7A mm Low Power Consumption Fan 9GA524P7G mm Low Power Consumption Fan 9GA524P7H mm Low Power Consumption Fan 9GA524P7M mm DC 19P65H mm DC 19P65M mm DC 19P612B mm DC 19P612H mm DC 19P612K mm DC 19P612M mm DC 19P612S mm DC 19P624H mm DC 19P624J mm DC 19P624M mm DC 19P624S mm Low Power Consumption Fan 9GA612L mm Low Power Consumption Fan 9GA612M mm Low Power Consumption Fan 9GA612P7G mm Low Power Consumption Fan 9GA612P7H mm Oil Proof Fan 9WF624H mm DC 19P612H61 83

319 Frame Size Category Model No. UL CSA TÜV page Frame Size Category Model No. UL CSA TÜV page 6 6 2mm DC 19P612M mm DC 19P612W mm DC 19P624H mm DC 19P624M mm DC 19P624W mm DC 19P648H mm Low Power Consumption Fan 9GA612H mm Low Power Consumption Fan 9GA612M mm Low Power Consumption Fan 9GA612P6G mm Low Power Consumption Fan 9GA612P6S mm Low Power Consumption Fan 9GA624H mm Low Power Consumption Fan 9GA624M mm Low Power Consumption Fan 9GA624P6G mm Low Power Consumption Fan 9GA624P6S mm Oil Proof Fan 9WF624H mm DC 9G612P4H1(11) mm DC 9G612P4S1(11) mm DC 9G624P4H1(11) mm DC 9G624P4S1(11) mm DC 9G648P4S1(11) mm DC 19R65F41(411) mm DC 19R65H41(411) mm DC 19R65M41(411) mm DC 19R612D41(411) mm DC 19R612F41(411) mm DC 19R612G41(411) mm DC 19R612H41(411) mm DC 19R612J41(411) mm DC 19R612M41(411) mm DC 19R612S41(411) mm DC 19R624D41(411) mm DC 19R624F41(411) mm DC 19R624G41(411) mm DC 19R624H41(411) mm DC 19R624J41(411) mm DC 19R624M41(411) mm DC 19R624S41(411) mm DC 19R648G41(411) mm DC 19R648H41(411) mm DC 19R648J41(411) mm DC 9A612F41(411) mm DC 9A612G41(411) mm DC 9A612H41(411) mm DC 9A612M41(411) mm DC 9A612S41(411) mm DC 9A624F41(411) mm DC 9A624G41(411) mm DC 9A624H41(411) mm DC 9A624M41(411) mm DC 9A624S41(411) mm Silent Fan 9S612F41(411) mm Silent Fan 9S612H41(411) mm Silent Fan 9S612M41(411) mm Silent Fan 9S612S41(411) mm Long Life Fan 19L612F mm Long Life Fan 19L612G mm Long Life Fan 19L612H mm Long Life Fan 19L612M mm Long Life Fan 19L612S mm Long Life Fan 19L624D mm Long Life Fan 19L624F mm Long Life Fan 19L624H mm Long Life Fan 19L624M mm Long Life Fan 19L624S mm Long Life Fan 19L648G mm Long Life Fan 19L648H mm Oil Proof Fan 9WF624H mm Splash Proof Fan 9WP612G41(411) mm Splash Proof Fan 9WP612H41(411) mm Splash Proof Fan 9WP624H41(411) mm Splash Proof Fan 9WP648H41(411) mm DC 9G612G11(111) mm DC 9G612S11(111) mm DC 9G624G11(111) mm DC 9G624H11(111) mm DC 9G624S11(111) mm DC 9G648G11(111) mm DC 9G648S11(111) mm Low Power Consumption Fan 9GA612P1H3(31) mm Low Power Consumption Fan 9GA612P1J3(31) mm Low Power Consumption Fan 9GA612P1K3(31) mm Low Power Consumption Fan 9GA612P1K6(61) mm Low Power Consumption Fan 9GA624P1J3(31) mm DC 9GV612P1G3(31) mm DC 9GV612P1H3(31) mm DC 9GV612P1L1(11) mm DC 9GV612P1M3(31) mm DC 9GV624P1G3(31) mm DC 9GV648P1H3(31) mm Counter Rotating Fan 9CR612P5G mm Counter Rotating Fan 9CR612P5H mm Counter Rotating Fan 9CR612H mm Counter Rotating Fan 9CR612S mm Counter Rotating Fan 9CRA612PG mm Counter Rotating Fan 9CRA612PS mm DC 19P812H mm DC 19P812M mm DC 19P824H mm DC 19P824M mm DC 19P812C mm DC 19P812H mm DC 19P812M mm DC 19P824H mm DC 19P824M mm DC 19P848C mm DC 19P848H mm Low Power Consumption Fan 9GA812P6G mm Low Power Consumption Fan 9GA812P6M mm Low Power Consumption Fan 9GA824P6G mm Low Power Consumption Fan 9GA824P6M mm DC 19R85F41(411) mm DC 19R85M41(411) mm DC 19R812E41(411) mm DC 19R812F41(411) mm DC 19R812G41(411) mm DC 19R812H41(411) mm DC 19R812L41(411) mm DC 19R812M41(411) mm DC 19R812S41(411) mm DC 19R824F41(411) mm DC 19R824G41(411) mm DC 19R824H41(411) mm DC 19R824L41(411) mm DC 19R824M41(411) mm DC 19R824S41(411) mm DC 19R848K41(411) mm DC 19R848S41(411) mm DC 9A812F41(411) mm DC 9A812G41(411) mm DC 9A812H41(411) mm DC 9A812L41(411) mm DC 9A812M41(411) Index by Frame Size/Safety Standards List

320 Index by Frame Size/Safety Standards List - Axial Fan Frame Size Category Model No. UL CSA TÜV page Frame Size Category Model No. UL CSA TÜV page mm DC 9A812S41(411) mm DC 9A824F41(411) mm DC 9A824G41(411) mm DC 9A824H41(411) mm DC 9A824L41(411) mm DC 9A824M41(411) mm DC 9A824S41(411) mm DC 9GV812P4J3(31) mm DC 9GV812P4K3(31) mm DC 9GV824P4K1(11) mm DC 9GV848P4K3(31) mm Silent Fan 9S812F41(411) mm Silent Fan 9S812H41(411) mm Silent Fan 9S812L41(411) mm Silent Fan 9S812M41(411) mm Silent Fan 9S824L41(411) mm Silent Fan 9S824M41(411) mm Oil Proof Fan 9WF824S mm Splash Proof Fan 9WP812G41(411) mm Splash Proof Fan 9WP812H41(411) mm Splash Proof Fan 9WP824H41(411) mm Splash Proof Fan 9WP848S41(411) mm Splash Proof Fan 9WS812F41(411) mm Splash Proof Fan 9WS812H41(411) mm Splash Proof Fan 9WS812M41(411) mm Splash Proof Fan 9WS824F41(411) mm Splash Proof Fan 9WS824H41(411) mm Splash Proof Fan 9WS824M41(411) mm Long Life Fan 19L812F mm Long Life Fan 19L812H mm Long Life Fan 19L812L mm Long Life Fan 19L812M mm Long Life Fan 19L812S mm Long Life Fan 19L824F mm Long Life Fan 19L824H mm Long Life Fan 19L824L mm Long Life Fan 19L824M mm Long Life Fan 19L824S mm Long Life Fan 19L848H mm DC 19P812A21(211) mm DC 19P812H21(211) mm DC 19P812M21(211) mm DC 19P824A21(211) mm DC 19P824H21(211) mm DC 19P824M21(211) mm DC 19P848H21(211) mm Low Power Consumption Fan 9GA812P2H1(11) mm Low Power Consumption Fan 9GA812P2M1(11) mm Low Power Consumption Fan 9GA812P2S1(11) mm Low Power Consumption Fan 9GA824P2S1(11) mm DC 9G812G11(111) mm DC 9G812H11(111) mm DC 9G812K11(111) mm DC 9G824G11(111) mm DC 9G824H11(111) mm DC 9GV824P1G3(31) mm DC 9G848G11(111) mm DC 9G848H11(111) mm Low Power Consumption Fan 9GA812P1H61(611) mm Low Power Consumption Fan 9GA812P1S61(611) mm Low Power Consumption Fan 9GA824P1H61(611) mm Low Power Consumption Fan 9GA824P1S61(611) mm DC 9GV812P1G3(31) mm DC 9GV812P1H3(31) mm DC 9GV812P1F3(31) mm DC 9GV812P1M3(31) mm DC 9GV848P1G3(31) mm Splash Proof Fan 9WV848P1H1(11) mm Counter Rotating Fan 9CRA812P8G mm Counter Rotating Fan 9CRA848P8G mm Counter Rotating Fan 9CR812H mm Counter Rotating Fan 9CR812S mm DC 19P912F41(411) mm DC 19P912H41(411) mm DC 19P912J41(411) mm DC 19P912L41(411) mm DC 19P912M41(411) mm DC 19P912W41(411) mm DC 19P924F41(411) mm DC 19P924H41(411) mm DC 19P924J41(411) mm DC 19P924L41(411) mm DC 19P924M41(411) mm DC 19P924W41(411) mm DC 19P948H41(411) mm DC 9A912F41(411) mm DC 9A912G41(411) mm DC 9A912H41(411) mm DC 9A912L41(411) mm DC 9A912M41(411) mm DC 9A912S41(411) mm DC 9A924F41(411) mm DC 9A924G41(411) mm DC 9A924H41(411) mm DC 9A924L41(411) mm DC 9A924M41(411) mm DC 9A924S41(411) mm Silent Fan 9S912F41(411) mm Silent Fan 9S912L41(411) mm Silent Fan 9S912M41(411) mm Silent Fan 9S924F41(411) mm Silent Fan 9S924L41(411) mm Silent Fan 9S924M41(411) mm Oil Proof Fan 9WF924H mm Splash Proof Fan 9WP912F mm Splash Proof Fan 9WP924B mm Splash Proof Fan 9WP924F mm Splash Proof Fan 9WP924H mm Splash Proof Fan 9WP924S mm Splash Proof Fan 9WS912F mm Splash Proof Fan 9WS912H mm Splash Proof Fan 9WS912L mm Splash Proof Fan 9WS912M mm Splash Proof Fan 9WS924F mm Splash Proof Fan 9WS924H mm Splash Proof Fan 9WS924L mm Splash Proof Fan 9WS924M mm Long Life Fan 19L912F mm Long Life Fan 19L912H mm Long Life Fan 19L912L mm Long Life Fan 19L912M mm Long Life Fan 19L912S mm Long Life Fan 19L924F mm Long Life Fan 19L924H mm Long Life Fan 19L924L mm Long Life Fan 19L924M mm Long Life Fan 19L948C mm Long Life Fan 19L948H mm Low Power Consumption Fan 9GA912P4G3(31) mm Low Power Consumption Fan 9GA912P4J3(31) mm Low Power Consumption Fan 9GA912P4S3(31) mm Low Power Consumption Fan 9GA924P4G3(31) 45

321 Frame Size Category Model No. UL CSA TÜV page Frame Size Category Model No. UL CSA TÜV page mm Low Power Consumption Fan 9GA924P4J3(31) mm Low Power Consumption Fan 9GA924P4S3(31) mm DC 9G912A21(211) mm DC 9G912H21(211) mm DC 9G912M21(211) mm DC 9G912S21(211) mm DC 9G924A21(211) mm DC 9G924H21(211) mm DC 9G924M21(211) mm DC 9G924S21(211) mm DC 9G948A21(211) mm DC 9G948H21(211) mm DC 9G948M21(211) mm DC 9G948S21(211) mm Oil Proof Fan 9WF924H mm Oil Proof Fan 9WF924S mm DC 9G912G11(111) mm DC 9G912H11(111) mm DC 9G924G11(111) mm DC 9G924H11(111) mm DC 9G948G11(111) mm DC 9G948H11(111) mm Low Power Consumption Fan 9GA912P1H3(31) mm Low Power Consumption Fan 9GA948P1H mm DC 9GV912P1G3(31) mm DC 9GV912P1H3(31) mm DC 9GV948P1H3(31) mm Splash Proof Fan 9WV948P1H mm DC 9G1212A41(411) mm DC 9G1212B41(411) mm DC 9G1212E41(411) mm DC 9G1212F41(411) mm DC 9G1212G41(411) mm DC 9G1212H41(411) mm DC 9G1212M41(411) mm DC 9G1224A41(411) mm DC 9G1224E41(411) mm DC 9G1224F41(411) mm DC 9G1224G41(411) mm DC 9G1224H41(411) mm DC 9G1224M41(411) mm DC 9G1248A41(411) mm DC 9G1248E41(411) mm DC 9G1248F41(411) mm DC 9G1248G41(411) mm DC 9G1248H41(411) mm DC 9G1248M41(411) mm DC 9GV1212P4G1(11) mm DC 9GV1224P4G1(11) mm DC 9GV1248P4J1(11) mm DC 9GV1248P4G1(11) mm DC 9GV1248P4H1(11) mm Silent Fan 9S1212F41(411) mm Silent Fan 9S1212H41(411) mm Silent Fan 9S1212L41(411) mm Silent Fan 9S1212M41(411) mm DC 9G1212E11(111) mm DC 9G1212F11(111) mm DC 9G1212G11(111) mm DC 9G1212H11(111) mm DC 9G1212M11(111) mm DC 9G1224E11(111) mm DC 9G1224F11(111) mm DC 9G1224G11(111) mm DC 9G1224H11(111) mm DC 9G1224M11(111) mm DC 9G1248E11(111) mm DC 9G1248F11(111) mm DC 9G1248G11(111) mm DC 9G1248H11(111) mm DC 9G1248M11(111) mm DC 9GV1212P1J1(11) mm DC 9GV1224P1H1(11) mm DC 9GV1224P1J1(11) mm DC 9GV1248P1J1(11) mm DC 9SG1212G mm DC 9SG1224G mm DC 9SG1224H mm DC 9SG1248G mm Oil Proof Fan 9WF1224H mm Splash Proof Fan 9WV1224P1H mm Splash Proof Fan 9WV1248P1J mm Long Life Fan 9GL1212E mm Long Life Fan 9GL1212F mm Long Life Fan 9GL1212G mm Long Life Fan 9GL1212H mm Long Life Fan 9GL1212M mm Long Life Fan 9GL1224E mm Long Life Fan 9GL1224F mm Long Life Fan 9GL1224G mm Long Life Fan 9GL1224H mm Long Life Fan 9GL1224M mm Long Life Fan 9GL1248E mm Long Life Fan 9GL1248F mm Long Life Fan 9GL1248G mm Long Life Fan 9GL1248H mm Long Life Fan 9GL1248M mm Long Life Fan 9LB1212H mm Long Life Fan 9LB1212M mm Long Life Fan 9LB1224H mm Long Life Fan 9LB1224M mm Long Life Fan 9LB1224S mm Long Life Fan 9LB1248H mm Long Life Fan 9LB1248M mm Splash Proof Fan 9WG1212E11-E mm Splash Proof Fan 9WG1212F11-E mm Splash Proof Fan 9WG1212G11-E mm Splash Proof Fan 9WG1212H11-E mm Splash Proof Fan 9WG1212M11-E mm Splash Proof Fan 9WG1224E11-E mm Splash Proof Fan 9WG1224F11-E mm Splash Proof Fan 9WG1224G11-E mm Splash Proof Fan 9WG1224H11-E mm Splash Proof Fan 9WG1224M11-E mm Splash Proof Fan 9WG1248E11-E mm Splash Proof Fan 9WG1248F11-E mm Splash Proof Fan 9WG1248G11-E mm Splash Proof Fan 9WG1248H11-E mm Splash Proof Fan 9WG1248M11-E mm Splash Proof Fan 9WP1212H11(111) mm Splash Proof Fan 9WP1224H11(111) mm Splash Proof Fan 9WP1248H11(111) mm Splash Proof Fan 9WS1212H11(111) mm Splash Proof Fan 9WS1212M11(111) mm Splash Proof Fan 9WS1224H11(111) mm Splash Proof Fan 9WS1224M11(111) mm Splash Proof Fan 9WS1248H11(111) mm Splash Proof Fan 9WS1248M11(111) mm Counter Rotating Fan 9CR1212PG mm DC 19E1312A mm DC 19E1312S mm DC 19E1324A Index by Frame Size/Safety Standards List

322 Index by Frame Size/Safety Standards List - Axial Fan Frame Size Category Model No. UL CSA TÜV page Frame Size Category Model No. UL CSA TÜV page mm DC 19E1324G mm DC 19E1324S mm DC 19E1348A mm DC 19E1348G mm DC 19E1348S mm DC 19P1312H11(111) mm DC 19P1312S11(111) mm DC 19P1324H11(111) mm DC 19P1324S11(111) mm DC 19P1348H11(111) mm DC 19P1348S11(111) mm DC 19P1412H mm DC 19P1412M mm DC 19P1424H mm DC 19P1424M mm DC 19P1448H mm DC 19P1448M mm Long Life Fan 19L1412H mm Long Life Fan 19L1412M mm Long Life Fan 19L1424H mm Long Life Fan 19L1424M mm Long Life Fan 19L1448H mm Long Life Fan 19L1448M mm Splash Proof Fan 19W1412H11-U mm Splash Proof Fan 19W1412M11-U mm Splash Proof Fan 19W1424H11-U mm Splash Proof Fan 19W1424M11-U mm Splash Proof Fan 19W1448H11-U mm Splash Proof Fan 19W1448M11-U mm Long Life Fan 9LB1412H mm Long Life Fan 9LB1412M mm Long Life Fan 9LB1412S mm Long Life Fan 9LB1424B mm Long Life Fan 9LB1448F mm Long Life Fan 9LB1424H mm Long Life Fan 9LB1424M mm Long Life Fan 9LB1424S mm Long Life Fan 9LB1448H mm Long Life Fan 9LB1448M mm Long Life Fan 9LB1448S mm Splash Proof Fan 9WB1412H mm Splash Proof Fan 9WB1412M mm Splash Proof Fan 9WB1412S mm Splash Proof Fan 9WB1424H mm Splash Proof Fan 9WB1424M mm Splash Proof Fan 9WB1448H mm Splash Proof Fan 9WB1448S mm DC 9GV1512H51(511) mm DC 9GV1512M51(511) mm DC 9GV1524M51(511) mm 147mm 25mm DC 19E4712L mm 147mm 25mm DC 19E4712M mm 147mm 25mm DC 19E4724F mm 147mm 25mm DC 19E4724H mm 147mm 25mm DC 19E4724L mm 147mm 25mm DC 19E4724M mm 147mm 25mm DC 19E4748F mm 147mm 25mm DC 19E4748H mm 147mm 25mm DC 19E4748L mm 147mm 25mm DC 19E4748M mm 147mm 25mm DC 19E4748S mm 15mm 51mm Splash Proof Fan 9WG5748P5G mm 15mm 51mm Splash Proof Fan 9WG5748P5H mm 15mm 51mm DC 19E5712F mm 15mm 51mm DC 19E5712H mm 15mm 51mm DC 19E5712K mm 15mm 51mm DC 19E5712M mm 15mm 51mm DC 19E5712Y mm 15mm 51mm DC 19E5724C mm 15mm 51mm DC 19E5724F mm 15mm 51mm DC 19E5724H mm 15mm 51mm DC 19E5724K mm 15mm 51mm DC 19E5724M mm 15mm 51mm DC 19E5748C mm 15mm 51mm DC 19E5748F mm 15mm 51mm DC 19E5748H mm 15mm 51mm DC 19E5748K mm 15mm 51mm DC 19E5748M mm 15mm 51mm DC 9GV5724H mm 15mm 51mm DC 9GV5748H mm 15mm 51mm DC 9SG5724P5H mm 15mm 51mm DC 9SG5748P5G mm 15mm 51mm DC 9SG5748P5H mm 51mm Splash Proof Fan 9WE1724K mm 15mm 51mm Splash Proof Fan 9WE5724K mm 15mm 51mm Splash Proof Fan 9WE5748K mm 51mm DC 19E1712F mm 51mm DC 19E1712H mm 51mm DC 19E1712K mm 51mm DC 19E1712M mm 51mm DC 19E1724C mm 51mm DC 19E1724H mm 51mm DC 19E1724K mm 51mm DC 19E1724M mm 51mm DC 19E1748C mm 51mm DC 19E1748H mm 51mm DC 19E1748K mm 51mm DC 19E1748M mm 51mm Long Life Fan 19L1712H mm 51mm Long Life Fan 19L1712M mm 51mm Long Life Fan 19L1724H mm 51mm Long Life Fan 19L1724M mm 51mm Long Life Fan 19L1748H mm 51mm Long Life Fan 19L1748M mm 15mm 51mm Long Life Fan 19L5712H mm 15mm 51mm Long Life Fan 19L5712M mm 15mm 51mm Long Life Fan 19L5724H mm 15mm 51mm Long Life Fan 19L5724M mm 15mm 51mm Long Life Fan 19L5748H mm 15mm 51mm Long Life Fan 19L5748M mm 15mm 12mm Counter Rotating Fan 9CR5748P9G mm 7mm DC 19E224AS mm 7mm DC 19E224H mm 7mm DC 19E224MH mm 7mm DC 19E224S mm 7mm DC 9EC224H mm 7mm DC 9EC248A mm 7mm DC 9EC248H1 169

323 Index by Frame Size/Safety Standards List Blower Frame Size Category Model No. UL CSA TÜV page 52mm 15mm Blower 19BC12FC mm 15mm Blower 19BC12GC mm 15mm Blower 19BC12HC mm 15mm Blower 19BC12MC mm 15mm Blower 19BC24GC mm 15mm Blower 19BC24HC mm 15mm Blower 19BC24FC mm 2mm Blower 9BD12FC mm 2mm Blower 9BD12HC mm 2mm Blower 9BD12SC mm 2mm Blower 9BD24FC mm 2mm Blower 9BD24HC mm 2mm Blower 9BD24SC mm 3mm Blower 19BD12FC mm 3mm Blower 19BD12HC mm 3mm Blower 19BD12MC mm 3mm Blower 19BD24FC mm 3mm Blower 19BD24HC mm 3mm Blower 19BD24MC mm 33mm Blower 19BM12GC mm 33mm Blower 19BM12HC mm 33mm Blower 19BM12MC mm 33mm Blower 19BM24GC mm 33mm Blower 19BM24HC mm 33mm Blower 19BM24MC mm 33mm Blower 9BMB12F mm 33mm Blower 9BMB12G mm 33mm Blower 9BMB12H mm 33mm Blower 9BMB12P2F mm 33mm Blower 9BMB12P2K mm 33mm Blower 9BMB12S mm 33mm Blower 9BMB24F mm 33mm Blower 9BMB24G mm 33mm Blower 9BMB24H mm 33mm Blower 9BMB24P2G mm 33mm Blower 9BMB24P2K mm 33mm Blower 9BMB24S mm 32mm Blower 19BF12HC mm 32mm Blower 19BF12MC mm 32mm Blower 19BF24HC mm 32mm Blower 19BF24MC mm 32mm Blower 9BFB12P2H mm 32mm Blower 9BFB24P2H mm 32mm Blower 19BJ12HC mm 32mm Blower 19BJ12MC mm 32mm Blower 19BJ24HC mm 32mm Blower 19BJ24MC mm 4mm Blower 19BG12HC mm 4mm Blower 19BG12MC mm 4mm Blower 19BG24HC mm 4mm Blower 19BG24MC1 296 Centrifugal Fan Frame Size Category Model No. UL CSA TÜV page 1mm 25mm Centrifugal Fan 9TM48P4H mm 25mm Splash Proof Centrifugal Fan 9W1TM48P4G mm 25mm Splash Proof Centrifugal Fan 9W1TM48P4H mm 91mm Centrifugal Fan 9TJ24PH mm 91mm Centrifugal Fan 9TJ48PH mm 91mm Splash Proof Centrifugal Fan 9W1TJ48PH mm 35mm Centrifugal Fan 9TN24P1H mm 35mm Centrifugal Fan 9TN48P1H mm 35mm Splash Proof Centrifugal Fan 9W1TN48P1H mm 69mm Centrifugal Fan 9TG24PG mm 69mm Centrifugal Fan 9TG48PG mm 69mm Splash Proof Centrifugal Fan 9W1TG48PH Index by Frame Size/Safety Standards List 33

324 Index by Frame Size/Safety Standards List Option 36mm sq. type Finger guards mm sq. type Finger guards mm sq. type Finger guards mm sq. type Finger guards mm sq. type Finger guards E 31 6mm sq. type Resin filter kits 19-13F mm sq. type Resin filter kits 19-13F2 35 6mm sq. type Resin filter kits 19-13F3 35 6mm sq. type Resin filter kits 19-13F4 35 6mm sq. type Resin Finger guards 19-13G 35 6mm sq. type Finger guards E 31 6mm sq. type Finger guards H 31 8mm sq. type Finger guards 19-49C 31 8mm sq. type Finger guards 19-49E 31 8mm sq. type Finger guards 19-49H 31 8mm sq. type Resin filter kits 19-12F mm sq. type Resin filter kits 19-12F2 35 8mm sq. type Resin filter kits 19-12F3 35 8mm sq. type Resin filter kits 19-12F4 35 8mm sq. type Resin Finger guards 19-12G 35 8mm sq. type EMC guards mm sq. type EMC guards mm sq. type Finger guards 19-99C 31 92mm sq. type Finger guards 19-99E 31 92mm sq. type Finger guards 19-99H 31 92mm sq. type Resin filter kits 19-11F mm sq. type Resin filter kits 19-11F mm sq. type Resin filter kits 19-11F mm sq. type Resin filter kits 19-11F mm sq. type Resin Finger guards 19-11G 35 92mm sq. type EMC guards mm type Inlet nozzle for centrifugal fan and splash proof centrifugal fan mm sq. type Finger guards 19-19C 31 12mm sq. type Finger guards 19-19E 31 12mm sq. type Finger guards 19-19H 31 12mm sq. type Finger guards 19-19K 31 12mm sq. type Resin filter kits 19-1F mm sq. type Resin filter kits 19-1F mm sq. type Resin filter kits 19-1F mm sq. type Resin filter kits 19-1F mm sq. type Resin Finger guards 19-1G 35 12mm sq. type EMC guards mm sq. type Finger guards mm sq. type Finger guards mm type Inlet nozzle for centrifugal fan and splash proof centrifugal fan mm type Finger guards mm sq. type Finger guards mm sq. type Finger guards H 32 15mm sq. type Finger guards mm sq. type Finger guards mm type Inlet nozzle for centrifugal fan and splash proof centrifugal fan mm type Finger guards mm type EMC guards mm type Finger guards mm type Finger guards mm type Finger guards E mm type Finger guards H mm type Finger guards J mm type Finger guards mm type Inlet nozzle for centrifugal fan and splash proof centrifugal fan mm type Finger guards mm type Finger guards 19-72H 33 2mm type Finger guards mm type Finger guards H 33 Recommended connectors for DC fans 36p Thermistor 36p IC L873 for DC fan sensor 36p 331 Model No. Category Matching Fan Size page

325 MEMO Index by Frame Size/Safety Standards List 332

326 Deleted models in this catalog Deleted models in this catalog Following models were deleted in this latest version of catalog. However, these models are not discontinued product. Please contact us for further assistance if necessary. Splash Proof Fan Size Model No. Frame material Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Air Flow Static Pressure SPL Operating Temperature Life Expectancy V V A W min -1 m³/min Pa inchh ² O db(a) h mm 19W812H41-U Aluminum , , mm 19W812F41-U Aluminum , , mm 19W812M41-U Aluminum , , mm 19W812L41-U Aluminum , , mm 19W824H41-U Aluminum , , mm 19W824F41-U Aluminum , , mm 19W824M41-U Aluminum , , mm 19W824L41-U Aluminum , , mm 19W848H41-U Aluminum , , mm 19W912H41-U Aluminum , , mm 19W912F41-U Aluminum , , mm 19W912M41-U Aluminum , , mm 19W912L41-U Aluminum , , mm 19W924H41-U Aluminum , , mm 19W924F41-U Aluminum , , mm 19W924M41-U Aluminum , , mm 19W924L41-U Aluminum , , mm 19W948H41-U Aluminum , , Thermal Speed Controlled Fan Size Model No mm 19P512T7H12 Plastics to mm 19P512T7H122 Plastics to mm 19P612T7H12 Plastics to mm 19P612T7H122 Plastics to mm 19P612T6H12 Plastics to mm 19P612T6H122 Plastics to mm 19R612T4H12(121) Plastics to mm 19R612T4H122(123) Plastics to mm 19P812T6H12 Plastics to mm 19P812T6H122 Plastics to mm 19R812T4H12(121) Plastics to mm 19R812T4H122(123) Plastics to mm 19P912T4H12(121) Plastics to mm 19P912T4H122(123) Plastics to mm 19P1212T4H12(121) Plastics to mm 19P1212T4H122(123) Plastics to mm 19R1212T1H12(121) Plastics to mm 19R1212T1H122(123) Plastics to 13.8 Frame Rated Voltage Operating Voltage Range Rated Current Rated Input Rated Speed Air Flow Static Pressure SPL Operating Temperature Life Expectancy material V V A W min -1 m³/min Pa inchh ² O db(a) h , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , to 7 6, 1 to 7 6, 1 to 7 6, 1 to 7 6, 1 to 7 6, 1 to 7 6, 1 to 6 6, 1 to 6 6, 1 to 6 6, 1 to 6 6, 1 to 6 6, 1 to 6 6, 1 to 6 4, 1 to 6 4, 1 to 6 4, 1 to 6 4, 1 to 6 4, 1 to 6 4, 333

327 CPU Cooler Intel Processor Socket Model No. Frame Rated Voltage Operating Voltage Range Rated Current Rated Speed c-a Thermal Resistance SPL Operating Temperature Life Expectancy material V V A min -1 K/W db(a) h X9912TD516 Plastics 12 9 to , , to 7 4, X9912TS16 Plastics 12 9 to , , to 7 4, X9912S16 Plastics 12 9 to , to 7 4, X9812TH16 Plastics 12 9 to , , to 6 4, X9812H16 Plastics 12 9 to , to 6 4, X9412G416 Plastics 12 7 to , to 7 4, X9612S516 Plastics 12 9 to ,.44 4 to 7 4, FC-PGA-2 19X7612H1176 Plastics 12 7 to , to 7 4, FC-PGA-2 19X7412S416 Plastics 12 7 to , to 7 4, FC-PGA 19X6512A216 Plastics 12 7 to , to 7 4, Storage temperature is -3 C to +7 C. Deleted models in this catalog 334

328 Network JAPAN SANYO DENKI CO., LTD. Head Office , Kita-Otsuka, Toshima-ku, Tokyo , Japan International Sales Dept. TEL: FAX: USA SANYO DENKI AMERICA, INC. 468 Amapola Avenue Torrance, CA 951 U.S.A. TEL: FAX: USA SANYO DENKI AMERICA, INC. Silicon Valley Office 17 Wyatt Dr.Suite 17 Santa Clara, CA 9554 U.S.A. TEL: FAX: USA SANYO DENKI AMERICA, INC. Chicago Office 134 Remington Road Suite E Schaumburg, IL U.S.A. TEL: FAX: USA SANYO DENKI AMERICA, INC. Detroit Office Schoolcraft Road Livonia, MI 4815 U.S.A. TEL: FAX: ARGENTINA VARITEL INGENIERÍA ELECTRÓNICA S.A. Manuel Baliña 456 Lomas de Zamora (B1832CCJ) Buenos Aires ARGENTINA. TEL: / 959 FAX: FRANCE SANYO DENKI EUROPE SA. P.A. Paris Nord 48 Allée des Erables-VILLEPINTE BP F ROISSY CDG Cedex France TEL: FAX: ITALY R.T.A. s.r.l. Via Enrico Mattei fraz. Divisa 272 Marcignago (PV) Italy TEL: FAX: GERMANY SANYO DENKI GERMANY GmbH Frankfurter Strasse Eschborn Germany TEL: FAX: GERMANY Altron GmbH & Co. KG Gaussstrasse Lehrte, Germany TEL: FAX: GERMANY Telemeter Electronic GmbH Joseph-Gansler-strasse 1 D-8669 Donauwoerth, Germany TEL: FAX: GERMANY R.T.A. Deutschland GmbH. Bublitzer Strasse 34 D-4599 Dusseldorf, Germany TEL: FAX: BENELUX SERVOTRONIC Wasseri jstraat 3, B-29 SCHOTEN, Belgium TEL: FAX: DENMARK SKAARUP IMCASE A/S Vasekaer 6-8 DK-273 Herlev, Denmark TEL: FAX: UNITED KINGDOM EAO LTD. Albert Drive, Burgess Hill, West Sussex RH15 9TN, U.K. TEL: FAX: UNITED KINGDOM ERIKS UK Amber Way Halesowen B62 8WG U.K. TEL: FAX: FINLAND WEXON OY Juhanilantie 4 FIN-174 Vantaa, Finland TEL: FAX: SPAIN HERREKOR S.L. Zamoka Lantegialdea Oialume Bidea 25,2115 ASTIGARRAGA (Guipúzcoa) Spain TEL: FAX: SPAIN R.T.A. Iberica - Motion Control Systems S.L. Calle Generalitat 22, 1º 3º 885 Gavà (Barcelona) Spain TEL: FAX: SPAIN DIODE Espana S.A. Orense 34, 282 Madrid, Spain TEL: FAX: SPAIN SERVICIO INDUSTRIAL DE ELECTRONICA S.A. Pol. Ind. Monguit-Centelles S/N 848 L ametlla Des Valles-Barcelona Spain TEL: FAX: SWITZERLAND Telemeter Electronic GmbH Kirchstraße 28 CH-8574 Lengwil-Oberhofen/TG, Switzerland TEL: FAX: PORTUGAL PROSISTAV, LDA Zona Industrial da Mota, Rua 7 Lote 6A Gafanha da Encarnação Ílhavo - Portugal TEL: FAX: CZECK REPUBLIC ENIKA spol. s.r.o. Nadorazni 69,59 1 Nova Paka, Czech Republic TEL: FAX: RUSSIA OOO WEXON , St. Petersburg Sofiyskaya ul., 14 Russia TEL: FAX: TURKIYE SDT Makine San. Ve Tic. Ltd. Sti. Ibrahimaga Mah. Fatih Sok. No: 6/ / Kadikoy / stanbul / Turkiye TEL: FAX: ISRAEL CONLOG LTD. 7 Leshem St., Petach Tikva, P.O.B 3571 Petach Tikva 49134, Israel TEL: FAX: ISRAEL RADION ENGINEERING COMPANY LTD. 11, Haslvim St.,P.O.B 7111 Petah-Tikvah, 4925, Israel TEL: FAX: SWEDEN All Motion Technology AB Tumstocksvagen 11B, S Taby, Sweden TEL: FAX: POLAND SANYO DENKI EUROPE SA. Poland Branch ul. Wodoci gowa Kraków, Polska TEL: POLAND SEMICON Sp. Z o.o. ul, Zwolenska 43, Warsaw, Poland TEL: FAX: HUNGARY Q-TECH Engineering Ltd. & Co. Batthyany Lajos u. 8. H-1161 Budapest, Hungary TEL: FAX: AUSTRALIA BRAEMAC PTY LTD 1/59-61 Burrows Road, Alexandria NSW 215, Australia TEL: FAX: AUSTRALIA Avnet Electronics Marketing Asia Sydney(NSW) 9B,9-11 South Street, Rydalmere NSW 2116, Australia TEL: FAX: AUSTRALIA SANTRON (AUST) Pty. Ltd. 17A Leader Street, Somerton Victoria 362, Australia TEL: FAX: INDIA SANYO DENKI SINGAPORE PTE.LTD. INDIA LIAISON OFFICE #14 (Old No.6/3), Avenue Road, Nungambakkam, Chennai India TEL: FAX: INDIA SYSTEM CONTROLS 73-B, Keonics Industrial Estate, Electronics City, Bangalore-56 1, India TEL: , FAX: INDIA Flexible Automation System PVT. LTD #412, Prestige Centre Point Cunningham Road, Bangalore , India TEL: FAX: TAIWAN SANYO DENKI TAIWAN CO., LTD. Room 128, 12F, No.96 Chung Shan N, Rd., Sec.2, Taipei 14, Taiwan, R.O.C. TEL: FAX: TAIWAN YUNG HO CO.,LTD. 5th Fl., 36. Kuan Chien Rd., Taipei 1, Taiwan, R.O.C. TEL: FAX: TAIWAN QuadRep Electronics [T] Ltd. 4F-1, No.79, Hsin Tai Wu Rd., Sec. 1, Hsi-Chih, Taipei, Taiwan, R.O.C. TEL: FAX: TAIWAN SUN HOLY TRADING CO., LTD. 3F, No.78 Sec.2 Chang An E. Rd Taipei Taiwan R.O.C TEL: FAX: SINGAPORE SANYO DENKI SINGAPORE PTE.LTD. 1 Hoe Chiang Road #14-3A/4 Keppel Towers Singapore TEL: FAX: SINGAPORE NEMATRON CONTROL SYSTEM (ASIA) PTE LTD. 11 Jalan Bukit Merah #5-8, Singapore TEL: FAX: SINGAPORE QuadRep Marketing (S) Pte Ltd. 53 Ubi Avenue 1, #3-3 Paya Ubi Industrial Park, Singapore TEL: FAX:

329 SINGAPORE PBA (S) Pte Ltd. 157 Sin Ming Road #2-1 Amtech Building (Annex Blk), Singapore TEL: FAX: INDONESIA PT. DIFA DAYA SELARAS Jln. Palmerah Utara II No.5 Jakarta 1148, Indonesia TEL: FAX: INDONESIA PT Flexindomas Jl Prof Dr Latumenten, No 17B Jakarta Barat, Indonesia TEL: FAX: HONG KONG SANYO DENKI (H.K.) CO., LIMITED Room 235,23/F,South Tower,Concordia Plaza,1 Science Museum Rd., TST East, Kowloon,Hong Kong TEL: FAX: HONG KONG Melco Industrial Supplies Co., Ltd. 1/F., Cheong Fat Factory Bldg., No Un Chau Street, Kowloon, Hong Kong TEL: FAX: HONG KONG SMC Pneumatics (Hong Kong) Ltd. 29/F., Clifford Centre, Cheung Sha Wan Rd, Kowloon, Hong Kong. TEL: FAX: HONG KONG FLEXIBLE AUTOMATION SYSTEM LTD Block B4, 1/FL, Tonic Industrial Centre, 19 Lam Hing Street, Kowloon Bay, Hong Kong. TEL: FAX: KOREA SANYO DENKI KOREA CO.,LTD. 5-2, Sunwha-dong Jung-gu Seoul, 1-13, Korea TEL: FAX: KOREA HY TECH CO., LTD. (former HAN YANG CORP.) Renaissance Tower B/D 11F #111, 456, Gongdeok-dong, Mapo-gu, Seoul, 121-2, Korea TEL: FAX: CHINA HONG KONG SANYO DENKI CO., LIMITED TIANJIN REPRESENTATIVE OFFICE Room AB 16th Floor TEDA Building, No. 256 Jie Fang Nan Road, Hexi District, Tianjin 342 China TEL: FAX: CHINA SANYO DENKI (Shenzhen) CO., LTD. Rm1-5 2/F Office Tower, Di Wang Commercial Centre Shun Hing Square, 52 Shen Nan Road East, Shenzhen,PRC TEL: FAX: CHINA BEIJING YANGHAI AUTOMATION TECHNOLOGY CO., LTD. Rm.18, 7 Huaqingjiayuan, Wudaokou,Haidian Beijing Beijing 18 China TEL: FAX: CHINA SHANGHAI DEZO INDUSTRIAL EQUIPMENT TECHNOLOGY CO.,LTD. (BEIJING YANGHAI SHANGHAI OFFICE) 6th F, No.173, 3rd Jiangchang Rd., Zhabei District, Shanghai, P.R. China Postal Code:2436 TEL: FAX: CHINA GUANGZHOU DE GAO AUTOMATION TECHNOLOGY CO.,LTD. (BEIJING YANGHAI GUANGZHOU OFFICE) 85, Huaxin Center, 45 Huanshi East Rd, Guanzhou, Guangdong, China, 5175 TEL: FAX: CHINA MELCO INTERNATIONAL TRADING(SHANGHAI) CO., LTD Flat B, 9/F, DaTong Commercial Tower, No.369 FuXing Road Central, Shanghai 225 China TEL: FAX: CHINA GUANGZHOU MELCO INTERNATIONAL SUPPLIES CO.,LTD Room 94-95, 9/F., Newpoly Tower, No.2 Zhongshan Liu Road, Guangzhou, China TEL: FAX: KOREA SAMHWA YANGHENG CO., LTD Dohwa-Dong, Mapo-ku, Seoul, Korea TEL: FAX: KOREA TPC Mechatronics Corp #111-85, Hwakok-Dong, Kanseo-ku, Seoul, Korea TEL: FAX: THAILAND Flexible Automation System Co.,Ltd 159 Soi Ladprao 94 (Srivara Town in Town) Wangthonglang, Bangkok 131 Thailand TEL: FAX: THAILAND SANYO DENKI (THAILAND) CO., LTD Exchange Tower, 388 Sukhumvit Road, Klongtoey, Bangkok 111 Thailand TEL: FAX: MALAYSIA Flexible Automation System Sdn Bhd (Kuala Lumpur) 6, Jalan USJ1/1B, 4762 UEP Subang Jaya, Selangor, Malaysia TEL: FAX: MALAYSIA OM Motion & Control Sdn.Bhd. No.15, 15A & 15B, Jalan Sasa 6, Taman Gaya, 818 Ulu Tiram, Johor Bahru, Johor, Malaysia TEL: FAX: CHINA KOYO ELECTRONICS (WUXI) CO.,LTD. No.118 Lixi Road, Wuxi, Jiangsu, China TEL: FAX: CHINA SHEN SING COMPANY LIMITED (Wu Xi Office) 18th floor, Unit H, Wah Kwong Building, 333 Zhong Shan Road, Wu Xi, Jian Su, China, 2141 TEL: FAX: CHINA QuadRep Electronics [C] Ltd. (Shanghai) Room 112, Block B, Lane 547, West Tian Mu Rd, Shanghai, China, 27 TEL: FAX: CHINA Capital Technology Co., Ltd. Rm JinLiHua, Commercial Building No.1133, Gongyuan Road, NO 31 District, Bao an, Shenzhen TEL: FAX: VIETNAM QuadRep 356 Cao Thang Str, Ward 12 District 1, HCM City, S.R. Vietnam TEL: FAX: Network MALAYSIA PBA (M) Sdn Bhd No 34-1, Block A, Jalan 1/116B, Sri Desa Entrepreneurs Park, Off Jalan Kuchai Lama, 582 Kuala Lumpur, Malaysia TEL: FAX: MALAYSIA QuadRep Malaysia Sdn Bhd 7-3B, Block F, Jalan PJU 1/3B,SunwayMas Commercial Centre,4731, Petaling Jaya, Selangor, Malaysia. TEL: FAX: CHINA SANYO DENKI SHANGHAI CO., LTD. Rm , Bldg A, Far East International Plaza,No.319, Xianxia Rd., Shanghai, 251 China TEL: FAX: CHINA SANYO DENKI SHANGHAI CO., LTD. Beijing Branch Room 1222, Tower B, Beijing COFCO Plaza, No.8 Jianguomennei Dajie, Dong Cheng District, Beijing 15 China TEL: FAX: CHINA SANYO DENKI (H.K.) CO.,LIMITED Chengdu Representative Office Room215B, Block A, Times Plaza, 2 Zongfu Road, Jinjiang District, Chengdu, 6116 China TEL:

330 MEMO 337

331