FEATURES. Life. E= Long life. (See note 5) Detents. Tolerance PAI PAM PAF P1I P1F P02.. (See note 4) P16

Transcription

1 MCHNIC SPCIFICTIONS Mechanical rotation angle: 3 ± lectrical rotation angle: 0 ± 0 Torque: 0.4 to Ncm. (0.6 to.7 in-oz) Stop torque: > Ncm. ( >7 in-oz) ife(*): Up to 0K cycles PTC-0 0 mm Cermet Potentiometer FTURS Cermet resistive element. IP4 protection according to IC 609 Plastic material according to U94V-0 lumina substrate. lso upon request: ow torque version vailable as SPDT switch aser trimming for tighter tolerances Wiper positioned at 0% or fully clockwise. Supplied in magazines for automatic insertion. ong life model for low cost control pot. applications Special tapers Mechanical detents CTRIC SPCIFICTIONS Range of values (*) Tolerance (*): ± 0% ± 30% Max. Voltage: 00 VDC (lin) 00 VDC (no lin) Nominal Power 70 C (8 F) (see power rating curve) 0.33 W (lin) 0.7 W (no lin) Taper (*) (og. & log. only Rn K) in ; og; log. Residual resistance(*): quivalent Noise Resistance: * Others upon request HOW TO ORDR Operating temperature: 40 C + 90 C ( 40 F + 94 F) OPTION XTRS PTC-0 H Series PTC-0 Rotors G K M R W X Y Z (See note ) Code Code Mounting Method H0 H. H0 H H0 H.P H0 HP V0 V V0 V V VP V3 VJ (See note ) Value Taper 0 = 00 W 04 = 00 K 0 = M 000 = C M (See note 3) = in. = og. C = log. Tolerance 00 = + 0% 3030 = + 30% (See note 4) ife = ong life (See note ) Detents PI PM PF PI PF P0.. P6 Magazine T (See note 6) Shaft /Thum. 0 = Fig. 0 = Fig. 7 = Fig. 7 (See note 9) Shaft / rotor colour RO= Red N= lack V= Green M= Yellow Z= lue M= rown GR= Grey N= Orange (See note 7) Wiper position PM = 0% PF = Final Torque = Standard = ow Torque (See note 8) NOTS: () "Z" adjustment only available on "H" versions. Rotor "G" only available in purple (shaft/rotor colour "VI"). () Terminal styles: "P" & "J" are crimped terminals. V=Vertical adjust; H=Horizontal djust (3) Value xample: Code: 0 Numb of zeros First two digits of the value. 000 = CM: SPDT switch 4 (4) Non standard tolerance, upon request. xample: +7% Code: () 07 0 Standard = 00 cycles ong = 0K cycles -% negative tolerance Others upon request. positive tolerance (6) Magazines: not available with the H0, V0 and V3 models, nor with adjustment types X, W, Y, Z. Non flammable: housing, rotor and shaft. (7) Colour shaft/rotor: Potentiometer without shaft: only rotor Potentiometer with shaft: only shaft (8) ow Torque: Ncm No detent option available for low torque models. (9) If you wish to use your own custom plastic shaft/knob/actuator please contact Piher for advice about compatible materials. NOT: The information contained here should be used for reference purposes only. rev

2 HOW TO ORDR CUSTOM DRWING PTC-0 H 0 + DRWING NUMR (Max. 6 characters) This way of ordering should be used for options which are not included in the "How to order" standard and optional extras. STNDRD OPTIONS Detents Packing Rotor colour Shaft colour Wiper position Torque ife None ulk Natural Natural Initial Standard 00 cycles ROTORS Without shaft º.7 With shaft. 0.7 = Screwdriver M = Hexagonal G = Hexagonal K = Cross slot thru hole thru hole thru hole thru hole R X = Wipers positioned at 0% djustable from collector side W = djustable from terminal side v = horizontal mount vertical adjust v (0) 4. S PIHR SPIN h () NOT = Please note relative terminal positions when ordering non linear tapers. Detail With thumbwheel Y = djustable from terminal side Z = djustable from collector side MOUNTING MTHODS = Initial S = Wiper = Final h = vertical mount horizontal adjust S h (.) = Initial S = Wiper = Final PIHR SPIN 3.. v () Crimped terminals Mod. J Mod. P 44

3 OPTIONS CONTCT SPDT SWITCH 0 SW Standard specs. Power Rating: 4V / m º 0 % CONTCT 4º ON position resistance: Insulation Resistance: 30 M Please contact Piher for ordering information. Mechanical rotation angle: 3º±º TPRS POSITIONING = inear = og. C = log. C 00% Rn P.M. 0% +0º R + % CCW P.F. CW Standard Special example NOT = Please note relative terminal positions when ordering non linear tapers. Std. Position = CCW TSTS TYPIC VRITIONS CTRIC IF MCHNIC IF (CYCS) TMPRTUR COFFICINT THRM CYCING DMP HT VIRTION (for each plane X,Y,Z) NOT: Out of range values may not comply these results C; 0.33 W 0 CPM... CPM 40 C; +90 C 6 90 C; 40 C % HR 0 Hz.... Hz. ± % ±3 % (Rn < M W) ±00 ppm (Rn <00 ±K) ±. % ± % % PCKGING Model OXS Units Without shaft With thumbwheel With shaft 000 (80 x 8 x 8 mm.) 800 (80 x 8 x 8 mm.) 400 (80 x 8 x 8 mm.) 8.9 Magazines for PTC-0 h.; h lso crimped term. h. P UTOMTIC INSRTION Magazines Units Magazines for PTC-0 V PTC-0H & PTC-0V 0 Pieces 3. lso crimped term. VP 4

4 RCOMMNDD CONNCTION Recommended connection scheme for Piher s position sensors (voltage divider) R V CC R C D POWR RTING CURV W (%) 00 % 40 % R 00 x R C SHFTS (for G and M rotor types, top view) Shafts, knobs & thumbweels are delivered at random position. Positioning available upon request Fig. 7 / Ref. Fig. 8 / Ref. 6 Fig. 9 / Ref. 9 Fig. 0 / Ref. 0 Fig. / Ref GNG Plastic Knob/ Plastic Shaft* 3 Ø Fig. / Ref. 06 Fig. / Ref. 03 Fig. 3 / Ref. 0 Fig. 4 / Ref. 603 Fig. 6 / Ref Ø.3. Fig. / Ref. 60 Fig. 3 / Ref. Fig. 4 / Ref. 0 Fig. 8 / Ref * Delivered unassembled (For assembled contact your nearest PIHR supplier) 46

5 THUMWHS (for G and M rotor types, top view) Shafts, knobs & thumbweels are delivered at random position. Positioning available upon request THUMWH Marking: configurable number of positions. xample of four positions marking: For R rotor type only 9 Fig. / Ref. 034 Upon request This innovative PT s with detents family has been specifically developed to allow the integration of otherwise large and expensive external mechanisms into the body of the majority of the 0 & mm. PS/PT/PTC potentiometer series thus allowing a high range of configurations: special tapers, torque, tolerances, linearity, cut track, etc. This detent design not only adds a "click" sensation of position, but also offers enormous savings in both cost and space for any given application. PM P04 PI P0 PF P06 P0 P07 P03 P08 Strong and weak detents can be mixed as per customer s request. Detent number and positions can be made or fitted to the customer needs or preferences. P09 P0 = 6º = 7.º Relative detent positions along the total mechanical travel. Unless otherwise specified the detents are evenly spaced (using the end points as reference) Wiper position PID PFD Wiper position *For more than 0 detents versions please contact your nearest PIHR distributor. Mechanical and/or electrical features may be affected by detents. Please see our separate PTs with detents datasheet at PI (wiper positioned at initial) PF (wiper positioned at final) ± ± PIHRSPIN Ø ±0. ±0. Fig. / Ref Fig. 6 / Ref. 039 Fig. 7 / Ref. 06 DTNT CONFIGURTIONS XMPS DTNT DTIS

6 DTNTS WITH CONSTNT VU ZONS application notes PIHR s potentiometers may feature special stepped outputs or constant voltage zones for the 0mm and mm product families. Constant value zones can be combined with strategically located stops matching the flat areas of the output. 0 stepped outputs version example: These constant voltage zones can be combined with PIHR s mechanical detents to provide exact alignment between the electrical output (flat areas) and the mechanical detent s positions. The result is a higher level of precision in controlling lighting, temperature, motor or other electronic control systems. In addition to established catalogue detent configurations, we will design and manufacture any other configuration on our tried-and-tested carbon/cermet & THM/SMD potentiometer technology and processes. With its exacting control capabilities, our 0mm and mm potentiometers series are well suited for many consumer applications such as ovens, ranges, dishwashers, lighting (dimmers), power hand tools, washing machines and HVC systems. 00% Un 88.9% Un 77.7% Un 66.6% Un.% Un 44.4% Un 33.3% Un.% Un.% Un 0% Un / 0º 00% 0% = = = = = = = = = d0 d d d3 d4 d d6 d7 d8 d9 Improved repeatability when the potentiometer s wiper position is located at detent nº8, the output votage will be exactly 88.9% Un d d d0 0º 34º d9 y combining the constant value zones with the detents, engineers can align the same voltage values with each of the detent stops when rotating the control both forward and backward. This provides clear mechanical positions that are not only repeatable, but perfectly aligned electrical outputs at each of the (detent) angles. Piher s detents also prevent output values from changing due to vibration or accidental rotor movements, furthering reliable control consistency. d3 d4 S d d6 Wiper position 6 d7 d8 S Design tip. Cost-effectiveness bsolute encoders can easily be replaced connecting the potentiometer to the microprocessor s analogue input. Main advantages Unique, non-overlapping values at each stop (detent position) Prevents output value change due to light vibration or accidental rotor micro-movements Fully customisable according to customer s needs Cost effective replacement for absolute encoders Disclaimer The product information in this catalogue is for reference purposes. Please consult for the most up to date and accurate design information. Piher Sensors & Controls S.., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Piher ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product described herein. Piher disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Piher s terms and conditions of sale, including but not limited to the warranty expressed therein, which apply to these products. No licence, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Piher. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Piher products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Piher for any damages arising or resulting from such use or sale. Please contact authorised Piher personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Information contained in and/or attached to this catalogue may be subject to export control regulations of the uropean Community, US, or other countries. ach recipient of this document is responsible to ensure that usage and/or transfer of any information contained in this document complies with all relevant export control regulations. If you are in any doubt about the export control restrictions that apply to this information, please contact the sender immediately. For any Piher International Corp. xports, Note: ll products / technologies are R99 Classified commodities. xports from the United States are in accordance with the xport dministration Regulations. Diversion contrary to US law is prohibited. ISO 400 URU VRITS Certification Nº S039 to V cording (000/3/C) / RoHS cpb (00/9/C) 44