RSP-2000 Series 2000W Single Output Enclosed Power Supplies

Transcription

1 RSP-000 Series 000W Single Output Enclosed Power Supplies Features Universal AC input / Full range Built-in active PFC function High efficiency up to 9% Forced air Cooling by built-in DC fan Output voltage programmable Active current sharing up to 00W (+) Built-in remote -OFF control / remote sense / auxiliary power / DC OK signal / OTP alarm signal Protections: Short circuit / Overload / Over oltage / Over temperature Optional conformal coating 5 years warranty Case No: DT 95 x 7 x 4mm Specification INPUT OUTPUT PROTECTI FUNCTI ENIRMENT oltage 90 ~ 64AC 7 ~ 70DC Frequency Power Factor 47 ~ 6 Hz 0.97/0AC at full load Efficiency 87% 90.5% 9% Current A/5AC 7A/0AC 6A/5AC 0A/0AC 6A/5AC 0A/0AC Inrush Current (Typ.) Leakage Current Cold start 50A <ma/ac MODEL No. RSP-000- RSP RSP oltage 4 48 Rated Current 00A A 4A Current Range 0~00A 0~A 0~4A Rated Power 00W 90W 06W Ripple Noise MAX. 50mp-p 00mp-p 00mp-p oltage Adj. Range 0.5~4 ~8 4~56 oltage Tolerance ±.0% ±.0% ±.0% Line Regulation ±.0% ± 0.5% ± 0.5% Load Regulation ±.0% ± 0.5% ± 0.5% Setup Rise Time 500ms, 60ms/0AC at full load Holdup Time (Typ.) 6ms/0AC at 75% load 0ms/0AC at full load Overload Over oltage Over Temperature 05~5% rated output power Protection Type: Constant current limiting, unit will shutdown o/p voltage after 5 sec. re-power on to recover 4.7~ ~5 57.6~67. Protection Type: Shut down o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down Output oltage Program (P) Adjustment of output voltage is allowable to ~5% of nominal output voltage. Please refer to the Function Manual Current Sharing Auxiliary Power (Aux) Remote /OFF Control Remote Sense DC Ok signal Working Temp. Working Humidity Up to 00W or (+) units. Please refer to the Function Manual 5/0.A, /0.8A By electrical signal or dry contact Power : open Power OFF: short, refer to Function Manual Compensate voltage drop on the load wiring up to 0.5, refer to function manual The isolated TTL signal out, refer to the function manual -5~+70 C (Refer to Derating Curve ) 0~90% RH non-condensing Storage Temp., Humidity -~+85 C, 0~95%RH Temp. Co-efficient ibration Safety Standards ±0.0% / C (0~50 C) 0~500Hz, G 0min./cycle, 60min. each along X, Y, Z axes UL60950-, TU EN approved SAFETY Withstand oltage I/P-O/P:KAC I/P-FG:KAC O/P-FG:0.5KAC EMC OTHERS Isolation Resistance I/P-OP, I/P-FG, O/P-FG:00M Ohms / 500DC / 5 C/70% RH EMC Emission Compliance to EN550 (CISPR), EN550 (CISPR) Class A, EN6000--, - EMC Immunity M.T.B.F. Packaging Compliance to EN5504, EN604-, EN , EN ,,4,5,6,8,, 59K hrs min. Telcordia SR- (Bellcore); 46.K hrs min. MIL-HDBK-7F (5 C).95Kg; 6pcs/.7Kg/.5CUFT. All parameters not specially mentioned are measured at 0AC input, rated load and 5 C or ambient temperature.. Ripple & noise are measured at 0MHz of bandwidth by using a twisted pair-wire terminates with a 0.uf & 47uf parallel capacitor.. Tolerance: Includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into final equipment. All the EMC tests are being executed by mounting the unit on a 70mm,*60mm metal plate with mm thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. 5. Derating maybe needed under low input voltages, Please check the derating curve for more details. 6. Under parallel operation, ripple of the output voltage may be higher than the SPEC at light load condition. It will go back to normal ripple level once the output load is more than 5%. Sunpower Technology LLP Orion House, Calleva Park, Aldermaston, Berkshire RG7 8SN Tel: +44 (0) sales@sunpower-uk.com

2 RSP-000 Series 000W Single Output Enclosed Power Supplies Mechanical Diagram Case No. 95D Unit:mm M4 L= CN50 SR CN504 + CN TB 90 -M4 L=4 59 Air flow direction 0.5 -M4 L= Block Diagram PFC fosc : 0KHz PWM fosc : 90KHz +S I/P EMI FILTER ACTIE INRUSH CURRENT LIMITING RECTIFIERS & PFC POWER SWITCHING RECTIFIERS & FILTER ORING FET + - PFC CTROL PWM CTROL O..P. DETECTI CIRCUIT ORING FET CTROL -S P TRANSCEIERS DA/DB DETECTI CIRCUIT MCU O.T.P. AUX POWER FAN MCU RECTIFIERS & FILTER /0.8A AUX POWER 5/0.A DATA ISOLATI T-Alarm DC-OK Remote -OFF Sunpower Technology LLP Orion House, Calleva Park, Aldermaston, Berkshire RG7 8SN Tel: +44 (0) sales@sunpower-uk.com

3 RSP-000 Series 000W Single Output Enclosed Power Supplies Static Characteristics 00 INPUT MODEL 4 48 LOAD (%) ,48 ~64AC 5AC 00AC 00W 00A 0W 90A 00W 85A 90W A 6W 68A 4W 60A 06W 4A 7.6W 5.7A 5W.5A AC 960W A 48W 5A 0.4W 7.A INPUT OLTAGE (AC) 60Hz Derating Curve Efficiency vs Load (48 Model) LOAD (%) for ~64AC EFFICIENCY (%) AMBIENT TEMPERATURE ( C) (HORIZTAL) LOAD The curve above is measured at 0AC. Sunpower Technology LLP Orion House, Calleva Park, Aldermaston, Berkshire RG7 8SN Tel: +44 (0) sales@sunpower-uk.com

4 RSP-000 Series 000W Single Output Enclosed Power Supplies Function Manual. Remote Sense The Remote Sense compensates voltage drop on the load wiring up to 0.5 PIN -S PIN +S + - LOAD - + CN50 Sense lines should be twisted in pairs to minimize noise pick-up. The +S signal should be connected to the positive terminal of the load whereas -S signal to the negative terminal.. Output oltage Programming (or P / remote voltage programming / remote adjust / margin programming / dynamic voltage trim) In addition to the adjustment via the built-in potentiometer, the output voltage can be trimmed to ~5% of the nominal voltage by applying EXTERNAL OLTAGE. PIN -S PIN +S PIN P - + CN50 PIN4 EXTERNAL OLTAGE (DC) +S & +, -S& -also need to be connected on CN50. out OLTAGE(%) OUTPUT for model for 4,48 model Non-Linear EXTERNAL OLTAGE (DC) OUTPUT CURRENT (%) OUTPUT OLTAGE (%) The rated current should change with the Output oltage Programming accordingly.. Remote -OFF Control The power supply can be turned /OFF individually or along with other units by using the "Remote -OFF" function. PIN7 Remote -OFF switch Between Remote -OFF and Switch Open +5-AUX Power Supply Status PIN +5-AUX Switch Short OFF - + CN50 Sunpower Technology LLP Orion House, Calleva Park, Aldermaston, Berkshire RG7 8SN Tel: +44 (0) sales@sunpower-uk.com

5 RSP-000 Series 000W Single Output Enclosed Power Supplies 4.Current Sharing with Remote Sense RSP-000 has the built-in active current sharing function and can be connected in parallel, up to 4 units, to provide higher output power as exhibited below : The power supplies should be paralleled using short and large diameter wiring and then connected to the load. Difference of output voltages among parallel units should be less than 0.. The total output current must not exceed the value determined by the following equation: Maximum output current at parallel operation=(rated current per unit) x (Number of unit) x 0.9 Under parallel operation, the minimum output load should be greater than 5% of total output load; otherwise, it is likely that only one unit operates whereas other units may enter standby mode or their LED status indicators may not turn on. When the total output current is less than 5% of the total rated current, or say (5% of Rated current per unit) x (Number of unit) the current shared among units may not be fully balanced. CN50/CN504 Function pin connection Parallel PSU PSU PSU PSU4 CN50 CN504 CN50 CN504 CN50 CN504 CN50 CN504 unit X unit unit 4 unit X X X is CN50/CN504 connected to plug pin, X is CN50/CN504 not connected to plug pin. RSP-000 RSP-000 RSP-000 RSP-000 PSU PSU PSU PSU4 - + CN504 TB - + CN504 TB - + CN504 TB - + CN CN50 CN50 CN50 CN50 TB - + LOAD Fig DA DB DA DB DA DB DA DB DA DB DA DB DA DB DA DB PSU CN50 PSU CN50 PSU CN50 PSU4 CN50 If the lines of CN50 are too long, they should be twisted in pairs to avoid the noise. DA,DB and are connected mutually in parallel. Sunpower Technology LLP Orion House, Calleva Park, Aldermaston, Berkshire RG7 8SN Tel: +44 (0) sales@sunpower-uk.com

6 RSP-000 Series 000W Single Output Enclosed Power Supplies Function Manual Mounting Instruction Hole No. Recommended Screw Size MAX. Penetration Depth L Recommended Tightening Torque M4 M 6mm 4mm 7~0Kgf-cm 6~ 8Kgf-cm Mounting Surface Chassis of RSP-000 Control Pin No. Assignment (CN50): HRS DF-DP-DS or equivalent Mating Housing HRS DF-DS or equivalent Terminal HRS DF-**SC or equivalent Mounting Screw L Pin No. Function +S -S P Description Positive sensing for remote sense. Negative sensing for remote sense. Connection for output voltage programming. (Note.) 4 This pin connect to the negative terminal(-). 5 DC-OK High (4.5 ~ 5.5) : When the out % ±6%. Low (0 ~ 0.5) : When out > = % ±6%. The maximum sourcing current is 0mA and only for output. (Note.) 6 T-ALARM High (4.5 ~ 5.5) : When the internal temperature (TSW or TSW open) exceeds the limit of temperature alarm. Low (0 ~ 0.5) : When the internal temperature (TSW or TSW short) under the limit temperature. The maximum sourcing current is 0mA and only for output. (Note.) 7 Remote The unit can turn the output on and off by electrical signal or dry contact between Remote -OFF and +5-AUX. (Note.) -OFF Short (4.5 ~ 5.5) : Power OFF ; Open (0 ~ 0.5) : Power ; The maximum input voltage is ,9,0 -AUX Auxiliary voltage output. The signal return is isolated from the output terminals (+ & -). +5-AUX Auxiliary voltage output, 4.5~5.5, referenced to -AUX. The maximum load current is 0.A. This output has the built-in "Oring diodes" and is not controlled by the Remote -OFF control. +-AUX Auxiliary voltage output, 0.6~., referenced to. The maximum load current is 0.8A. This output has the built-in "Oring diodes" and is not controlled by the Remote -OFF control. Note: Non-isolated signal, referenced to the output terminals (-). Note: Isolated signal, referenced to -AUX. LED Indicators & Corresponding Signal at Function Pins = > Function LED DC-OK GREEN DC-NG RED T-OK GREEN T-ALARM RED *Signal between function pin and "-AUX". Description When output voltage > % ± 5% of o rated. When output voltage = % ± 5% of o rated. When the internal temperature (TSW & TSW short) is within safe limit > = When the internal temperature (TSW or TSW open) exceeds the limit of temperature alarm * Signal 0 ~ ~ ~ ~ 5.5 Power Supply Output OFF Control Pin No. Assignment (CN50): HRS DF-6DP-DSA or equivalent Mating Housing Terminal HRS DF-6DS or equivalent HRS DF-**SC or equivalent Pin No. Function Description,,4 DA DB Differential digital signal for parallel control. Differential digital signal for parallel control. 5,6 These pins connect to the negative terminal (-). Control Pin No. Assignment (CN504): Pin No., Function Terminal resistance Description CN504 is the selector of terminal resistor that is designed for DA/DB signals and parallel control function. AC Input Terminal Pin No. Assignment Pin No. Assignment Diagram AC/N AC/L FG Maximum mounting torque 8Kgf-cm DC Output Terminal Pin No. Assignment Assignment Diagram +, - Maximum mounting torque 0Kgf-cm Sunpower Technology LLP Orion House, Calleva Park, Aldermaston, Berkshire RG7 8SN Tel: +44 (0) sales@sunpower-uk.com