25W Multiple-Stage Output Current LED Power Supply

Transcription

1 5W MultipleStage Output Current LED Power Supply LCM5 s eries F 0 M M SELV 8 Features Output current level selectable by DIP S.W. ~77VAC input only Builtin active PFC function Protections: Short circuit / Over temperature Cooling by free air convection Fully isolated plastic case Class Ⅱ power unit, no FG Builtin 0~0VDC and PWM signal dimming function IP0 design No load power consumption <0.5W(Note.7) Power supplies synchronization function up to 0 units 3 years warranty Applications Indoor LED lighting Office LED lighting LED decorative lighting Description LCM5 is a 5Watts LED power supply that one single unit supplies multiple current levels, // ///. The current levels are easily switched by adjusting the builtin DIP switch. LCM5 also provides the dimming function that control by external a 0~0VDC or PWM signal. Moreover, the synchronization design allows the dimming for up to 0 units of LCM5 to be controlled simultaneously. Model Encoding LCM 5 Output power Series name File Name:LCM5SPEC 04038

2 5W MultipleStage Output Current LED Power Supply LCM5 s eries SPECIFICATI MODEL OUTPUT INPUT PROTECTI FUNCTI ENVIRMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RANGE RATED POWER SETUP, RISE TIME VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(max.) LEAKAGE CURRENT WORKING TEMP. WORKING HUMIDITY SAFETY STANDARDS LCM5 SELECTABLE CURRENT Note.3 RIPPLE CURRENT ±5.0% RIPPLE & NOISE (max.) Note. 400mVpp NO OUTPUT VOLTAGE (max.) 59V CURRENT ACCURACY HOLD UP TIME (Typ.) SHORT CIRCUIT OVER TEMPERATURE DIMMING SYNCHRIZATI Note.5 500ms, 50ms / 30VAC at full load Note.4 Note.6 STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATI WITHSTAND VOLTAGE ISOLATI RESISTANCE EMC EMISSI EMC IMMUNITY MTBF 6 ~ 54V ±5.0% ~ 77VAC 54 ~ 39VDC 47 ~ 63Hz 6 ~ 4V 6 ~ 36V 6 ~ 8V 6 ~ 4V PF 0.94/30VAC, PF 0.9/77VAC at full load (Please refer to "Power Factor Characteristic" curve) 86% 0.7A/30VAC <0.5mA / 40VAC 0.5A/77VAC 30 ~ + (Refer to "Derating Curve") 0 ~ 90% RH noncondensing 40 ~ +, 0 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 6 ~ 50V 8.9W 5.W 30ms / 30VAC at full load TOTAL HARMIC DISTORTI THD<0% when output loading 50% at 30VAC input and output loading 75% at 77VAC input COLD START 0A(t width= μs measured at 50% I peak) at 30VAC Constant current limiting, recovers automatically after fault condition is removed Please see "Dimming Operation" Please see "Synchronization Operation" 0 ~ 500Hz, G 0min./cycle, period for min. each along X, Y, Z axes UL8750, CSA C. NO , ENEC EN6347, EN63473, EN6384 independent approved I/PO/P:3.75KVAC ; I/PDA ± :.875VAC ; O/PDA ± :.875VAC I/PO/P:>00M Ohms / 500VDC / 5 / 70% RH Compliance to EN5505, EN003 Class C( 50% load) ; EN0033 Compliance to EN004,3,4,5,6,8,, EN5504, EN6547 light industry level (surge KV), criteria A 98.6K hrs min. MILHDBK7F (5 ) DIMENSI 05*68*3mm (L*W*H) PACKING 0.6Kg ; 7pcs/.5Kg/.04CUFT. All parameters NOT specially mentioned are measured at 30VAC input, rated load and 5 of ambient temperature.. Ripple & noise are measured at 0MHz of bandwidth by using a " twisted pairwire terminated with a 0.uf & 47uf parallel capacitor. 3. Please see "DIP switch table". 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. Length of set up time is measured at first cold start. Turning /OFF the power supply may lead to increase of the set up time. 6. Efficiency is measured at /50V output set by DIP switch. 7. No load power consumption<0.5w is measured at 30VAC, with lighting fixture connected and output current dimmed to 0%. 8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must requalify EMC Directive on the complete installation again. 4V Shut down o/p voltage, recovers automatically after temperature goes down File Name:LCM5SPEC 04038

3 5W MultipleStage Output Current LED Power Supply LCM5 s eries Block Diagram PFC fosc : 45KHz PWM fosc : 70KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER CURRENT LIMITING +V V DIM+ DIM PFC CTROL O.L.P. O.T.P. PWM CTROL DETECTI CIRCUIT Derating Curve Static Characteristics 00 Others AMBIENT TEMPERATURE ( ) (HORIZTAL) INPUT VOLTAGE (V) Hz DIP Switch Table LCM5 is a multiplestage output current supply, selection of output current through DIP switch as table below. Io DIP S.W (Factory Setting) File Name:LCM5SPEC 04038

4 5W MultipleStage Output Current LED Power Supply LCM5 s eries Power Factor Characteristic Constant Current Mode Constant Current Mode % 0% 30% 40% 50% % 70% % 90% 00% (5W) (30Vac Input) 0.4 0% 0% 30% 40% 50% % 70% % 90% 00% (5W) (77Vac Input) Total Harmonic Distortion Characteristic % 0% 30% 40% 50% % 70% % 90% 00% (5W) (30Vac Input) 0 0% 0% 30% 40% 50% % 70% % 90% 00% (5W) (77Vac Input) EFFICIENCY vs LCM5 possess superior working efficiency that up to 86% c an be reached in field applications % 0% 30% 40% 50% % 70% % 90% 00% 45 0% 0% 30% 40% 50% % 70% % 90% 00% (30Vac Input) (77Vac Input) File Name:LCM5SPEC 04038

5 5W MultipleStage Output Current LED Power Supply LCM5 s eries DIMMING OPERATI Builtin in dimming function, output constant current level can be adjusted through output terminal by 0 ~ 0Vdc or 0V PWM signal between DIM+ and DIM. Please DO NOT connect "DIM " to "Vo". 0 ~ 0V dimming function for output cur rent adjustment (Typical) Di mming value Output current 0V V V 3V 4V 5V 6V 7V 8V 9V 0V OPEN 0% 0% 0% 30% 40% 50% % 70% % 90% 00% 00%~08% 0V PWM signal for output current adjustment (Typical): Frequency range :00Hz ~ 3KHz Duty value 0% 0% 0% 30% 40% 50% % 70% % 90% 00% OPEN Output current 0% 0% 0% 30% 40% 50% % 70% % 90% 00% 00%~08% SYNCHRIZATI OPERATI 0 drivers(max.) synchronization ( master + 9 slaves). Maximum cable length between each units : 0 meters. Maximum cable length from the master unit to each end of the last slave units : 0 meters. The lights driven by LCM units(slaves) can be dimmed synchronously through a LCM unit(the master) directly controlled via 0~0Vdc or 0V PWM dimming function. The wiring is shown as below. LCM5 ( Slave ) LCM5 (Master) LCM5 (Slave 4) LCM5 ( Slave 5) LCM5 (Slave 9) SYN.... SYN. SYN. SYN SYN. CN0 CN00 +Vo Vo DIM DIM+ 0m max. CN00, CN0 : used to synchronously control the LCM units in parallel. 0~0Vdc or 0V PWM 0m max. 0m max File Name:LCM5SPEC 04038

6 5W MultipleStage Output Current LED Power Supply LCM5 s eries Mechanical Specification 05 Case No.LCM5 Unit:mm T case : Max. Case Temperatu re. 6 TB 35 TB 3 4 CN 0 0, CN 0 T case Bottom View M 3 Terminal Pin No. Assignment(TB) Pin No. Assignment Pin No. +Vo 3 Vo 4 Assignment DIM DIM+ Terminal Pin No. Assignment(TB) Pin No. Assignment AC/L AC/N SYN. Connector(CN00/CN0):JST BBPHKL or equivalent Pin No. Assignment Mating Housing + JST PHR or equivalent Terminal JST SPH00TP0.5S or equivalent Note:Please use wires with 0.5~.5mm (3~0AWG) of crosssection for TB and wires with 0.5~.5 mm (6~0AWG) of cross section for TB. Installation Manual Please refer to : lationsearch.html File Name:LCM5SPEC 04038