40W Multiple-Stage Output Current LED Power Supply E E E E E E E E E E E E E E E

Transcription

1 0W Multiple-Stage Output Current LED Power Supply LCM-0DA series SPECIFICATI MODEL OUTPUT INPUT PROTECTI FUNCTI ENVIRMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RANGE RATED POWER SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT WORKING TEMP. WORKING HUMIDITY SAFETY STANDARDS DALI STANDARDS LCM-0DA SELECTABLE CURRENT Note. 0mA RIPPLE CURRENT Note. 000ms, ms / 0VAC at rated power Note. Note.6 STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATI MTBF ~ 00V ~ V ~ 67V ~ 7V ~ V ~ 0V W Ó% RIPPLE & NOISE (max.) Note. mvp-p NO OUTPUT VOLTAGE (max.) 0V CURRENT ACCURACY TOTAL HARMIC DISTORTI SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE AUXILIARY POWER TEMP. COMPENSATI DIMMING SYNCHRIZATI WITHSTAND VOLTAGE ISOLATI RESISTANCE EMC EMISSI EMC IMMUNITY Ó.0% 6ms/0VAC at rated power ~ 9VAC ~ 7VDC 7 ~ 6Hz 90.% -0 ~ 60 J (Refer to "Derating Curve") 0 ~ 90% RH non-condensing -0 ~ J, 0 ~ 9% RH Ó 0.0%/ J (0 ~ 0 J) 0 ~ Hz, G 0min./cycle, period for 60min. each along X, Y, Z axes I/P-O/P:.7KVAC Compliance to EN0, EN0-- Class C( Ù% rated power) ; EN0-- Compliance to EN0--,,,,6,8,, EN0, EN67 light industry level (surge KV), criteria A 9.6K hrs min. MIL-HDBK-7F ( J) DIMENSI.*8.*mm (L*W*H) PACKING 0.Kg ; pcs/kg/.cuft J ~ 6V UL870, ENEC EN67-, EN67--,EN68 independent approved IEC686-0, 0, 07 I/P-O/P:>00M Ohms / VDC / J/ 70% RH ma ma ma ma 00mA Total harmonic distortion will be lower than 0% when output loading is 7% or higher 0.A/0VAC <0.mA / 0VAC Constant current limiting, recovers automatically after fault condition is removed 0 ~ 0V Protection type : Shutdown o/p voltage, re-power on to recover 90 J Ó 0 J (RTH) 0.9A/77VAC Protection type : Shut down o/p voltage, re-power on to recover 0mA for driving fan; Tolerance Ó% By external NTC(not provide with the power supply), please see "Temperature compensation operation" Please see "Dimming Operation" Please see "Synchronization Operation" ½ º PF Ù 0.98/0VAC, PF Ù0.97/77VAC at rated power (Please refer to "Power Factor Characteristic" curve) g COLD START 0A(t width=60 s measured at 0% I peak) at 0VAC File Name:LCM-0DA-SPEC 0--0

2 0W Multiple-Stage Output Current LED Power Supply LCM-0DA series Mechanical Specification Case No.LCM-60A Unit:mm r TB T case TB CN0 CN00 0 TB 6 Block Diagram M Terminal Pin No. Assignment(TB) Pin No. Assignment Pin No. AC/L AC/N PUSH 7.8 Assignment DA DA- Terminal Pin No. Assignment(TB) Pin No. Assignment Pin No. FAN -FAN Terminal Pin No. Assignment(TB) Pin No. Assignment Vo -Vo Connector(CN0/CN00):JST BB-XH or equivalent Pin No. Assignment Mating Housing Terminal,, - JST XHP or equivalent Assignment NTC -NTC JST SXH-00T-P0.6 or equivalent PFC fosc : 60KHz PWM fosc : KHz Vaux I/P EMI FILTER & PFC CIRCUIT POWER SWITCHING & FILTER O.L.P. MCU V -V DIM DIM- PFC CTROL O.L.P. O.T.P. PWM CTROL O.V.P. DETECTI CIRCUIT Derating Curve Static Characteristics Others (%) mA (%) AMBIENT TEMPERATURE ( J) (HORIZTAL) INPUT VOLTAGE (V) 60Hz File Name:LCM-0DA-SPEC 0--0

3 0W Multiple-Stage Output Current LED Power Supply LCM-0DA series DIP Switch Table LCM-0DA is a multiple-stage output current supply, selection of output current through DIP switch as table below. Io DIP S.W. 6 0mA ma ma ma(factory Setting) ma 00mA Power Factor Characteristic Constant Current Mode Constant Current Mode PF PF % 0% 0% 0% 0% 60% 70% % 90% 00% (0Vac Input) (0W) (0W) 0% 0% 0% 0% 0% 60% 70% % 90% 00% (0W) (77Vac Input) (0W) EFFICIENCY vs LCM-0DA series possess superior working efficiency that up to 9% can be reached in field applications. 9.0% 9.0% 90.0% 90.0% 8.0% 8.0% EFFICIENCY (%).0% 7.0% 70.0% 6.0% 60.0% 0 EFFICIENCY (%).0% 7.0% 70.0% 6.0% 60.0% 0.0% 00.0% % 0.0%.0% 0% 0% 0% 0% 0% 60% 70% % 90% 00%.0% 0% 0% 0% 0% 0% 60% 70% % 90% 00% (0Vac Input) (77Vac Input) File Name:LCM-0DA-SPEC 0--0

4 0W Multiple-Stage Output Current LED Power Supply LCM-0DA series DIMMING OPERATI PUSH dim(primary side) Ignore To avoid reaction on AC spike Short push Push to turn -OFF Long push Dimming up or down Reset push Setting light to 00% <0.0 sec. 0.~ sec..~0 sec. > sec. Maximum number of drivers up to 0 pcs. Maximum length of the cable, from push button to last driver is meter. Factory setting at 00%. When the light is lower than 0% it will always dim up, or when the light output is higher than 90% it will always dim down. LCM-0DA DA- DA PUSH AC/N AC/L Push Button AC/N AC/L Warning: The pushbutton can only be connected in between the PUSH terminal of LCM-0DA and AC/L (brown or black color). It would cause short circuit if it is connected to AC/N. DALI interface(primary side) DALI protocol including 6 groups and 6 addresses. First step is fixed at % light output. SYNCHRIZATI OPERATI 0 drivers(max.) synchronization ( master 9 slaves) Maximum length of the cable from first driver to last driver is meter. LCM-0DA (Slave ) LCM-0DA LCM-0DA (Master) (Slave ) File Name:LCM-0DA-SPEC 0--0

5 0W Multiple-Stage Output Current LED Power Supply LCM-0DA series TEMPERATURE COMPENSATI OPERATI 0 NTC derating curve 00 Output Io (%) K [ 0KO 0K [ 0KO 70K [ 70KO Sensed Temperature(degree) LCM-0DA have the built-in temperature compensation function (T ô,io õ). By connecting a temperature sensor (NTC resistor) between the NTC /- terminal of LCM-0DA and the detecting point on the lighting system or the surrounding environment, output current of LCM-0DA could be correspondingly changed to ensure the long life of LED..LCM-0DA can still be operated well when the NTC resistor is not connected and the value of output current will be the current level that you set through the DIP switch.. NTC resistance 0K 0K 70K Output Current < 60 J, 00% of the rated current (corresponds to the setting current level) > 60 J, output current begin to reduce, details please refer to the curve. < 70 J, 00% of the rated current (corresponds to the setting current level) > 70 J, output current begin to reduce, details please refer to the curve. < J, 00% of the rated current (corresponds to the setting current level) > J, output current begin to reduce, details please refer to the curve. Notes:. MW does not offer the NTC resistor and all the data above are measured by using THINKING TTC0 series.. If other brands of NTC resistor is applied,please check the temperature curve first.. Synchronization function of the power supply will be invalid when the "temperature compensation" function is in use. File Name:LCM-0DA-SPEC 0--0