Downloaded From JFETC.COM Fri, 27 Apr :37: * valid at time of download *
|
|
- Laureen Hutchinson
- 6 years ago
- Views:
Transcription
1 JFBAR-TP-M-101 (RV.3) FILD INSPCTION OF JFBAR THRAD Downloaded From JFTC.COM JUN 2017 JF STL CORPORATION
2 JFBAR-TP-M-101 (RV.3) Page-1 1 SCOP This procedure describes the field inspection for JFBAR. 2 PIN THRAD INSPCTION The tools and gauges required for field inspection may vary dependent on the particular situation, but for most running and pulling operations the following equipment is sufficient: Depth Gauge (Pit gauge) Rotary tools 1 Fine Tooth Triangle File (Small) Scotch Brite mery Cloth Scale or Vernier Calipers The pin thread inspection criteria and actions are shown in Fig. 1. Inspection is conducted visually and by touch of hand, any repairs to the connection should be conducted in accordance with the requirements of Fig.1. Slight burrs or damage to threads may be removed with emery cloth and moderate damage may be repaired with file, followed with emery cloth. There are two types of pin end, swaged and un-swaged end. The difference between those two are shown in Fig. 2. Downloaded From JFTC.COM 3 BOX THRAD INSPCTION The tools and gauges required for field inspection may vary dependent on the particular situations, but for most running and pulling operations the following equipment is sufficient: Depth Gauge (Pit gauge) Fine Tooth Triangle File (Small) Scotch Brite mery Cloth OD Micrometer The box thread inspection criteria and actions are shown in Fig. 3. Inspection is conducted visually and by touch of hand, any required repairs to the connection should be conducted in accordance with the requirements of Fig.3. Slight burrs or damage to threads may be removed with emery cloth and moderate damage may be repaired with file, followed with emery cloth.
3 JFBAR-TP-M-101 (RV.3) Page-2 Fig. 1 PIN VISUAL INSPCTION CRITRIA AND ACTIONS D C B A Minimum length of full crested threads(table 1) Permitted black crested threads Condition Zone Criteria Action Corrosion C, Pitting less than 0.004" (0.1mm) deep or minor surface corrosion. Hand repair with soft bristle (no steel wire) brush or emery cloth Deeper than 0.004" (0.1mm) Cut off & re-thread D No pitting If present then cut off & repair Light surface corrosion (Rust) Hand repair with Scotch Brite or #400 emery cloth DO NOT ALTR SAL DIMNSION. Repair should be made in a larger area than actual surface corrosion and should move around the diameter of seal. Burr, Tear, Ding, Mash, Scratch C, Any condition which could cause galling, i.e., conditions described greater than 0.01" (0.3mm) Hand repair with a fine triangle file or emery cloth. Repair should be made in a larger area than actual effected area and should move around the diameter of thread. Otherwise reject. D Not If present then cut off & Downloaded From JFTC.COM Phosphate Coating (Carbon Steel) Bead Peening Carbon steel ( 4-1/2 ) and High chrome steel* C, D, C, D, Must be present (xcept Mill Finish nd) Inspect for medium gray surface color normal wear is expected and. Inspect for peened surface normal wear is expected and re-thread Phosphate coat if not present Bead peen if not present *Note: Definition of High chrome steel : Containing 9% or more chromium steel.
4 JFBAR-TP-M-101 (RV.3) Page-3 Fig. 2 Two types of Pin nd and Bore Swaged nd (Thin Wall) Un-Swaged nd Table 1 Minimum Length of Full Crested Thread (measured from pin-nose) OD Full Crested Length (in) (mm) Downloaded From JFTC.COM Note: 50% of threads in this area to be full crested over at least 180 degrees of their circumference.
5 JFBAR-TP-M-101 (RV.3) Page-4 Fig. 3 BOX VISUAL INSPCTION CRITRIA AND ACTIONS D C B A Condition Zone Criteria Action Corrosion C, Slight imperfections and light surface corrosion, i.e., less than 0.004" (0.1mm) Hand repair with soft bristle (no steel wire), emery cloth or Scotch Brite All other imperfections deeper than 0.004" (0.1mm) Reject. Burr, Tear, Ding, Mash, Scratch D No pitting Reject. Light surface corrosion (Rust) Coupling O.D. & I.D. bore C, Phosphate C, D, Copper plating CLAR- PLAT Pitting or corrosion Less than 0.020" (0.5mm) deep Deeper than 0.020" (0.5mm) Any condition which could cause galling, i.e., conditions described greater than 0.01" (0.3mm) Downloaded From JFTC.COM D Not Reject. Must be present Inspect for medium gray surface color. C, D, C, D, Inspect for copper plated surface. Inspect for CLAR-PLAT surface. Repair with Scotch Brite or #400 emery cloth. DO NOT ALTR SAL DIMNSION. Repair should be made in a larger area than actual surface corrosion and should move around the diameter of seal. Grind to round bottom & smooth edge. Keep within JFBAR tolerances Reject. Hand repair with a fine triangle file or emery cloth. Repair should be made in a larger area than actual effected area and should move around the diameter of thread. Otherwise reject Phosphate coat if not present Reject or re-plate. Reject or re-plate. *Note: Definition of High chrome steel : Containing 9% or more chromium steel.
Downloaded From JFETC.COM Sat, 21 Apr :39: * valid at time of download *
FOX-TP-M-101 FILD INSPCTION OF FOX THRAD Downloaded From JFTC.COM January 2008 JF STL CORPORATION HUNTING OILFILD SRVICS INTRNATIONAL FOX-TP-M-101 Page-1 1. SCOP This describes the field inspection of
More informationVisual Testing of Pipe Threads
From NDT Technician, Vol. 10, No. 1, pp: 1 5. Copyright 2011 The American Society for Nondestructive Testing, Inc. The American Society for Nondestructive Testing www.asnt.org FOCUS AAs an oil well is
More informationEXTERNAL FEATURE: Feature on the part being delivered to a Lisk customer which is visible without disassembly.
1.0 Purpose: 1.1 This procedure establishes the Engineering, Manufacturing and Quality definitions, requirements, and inspection criteria for workmanship of machined parts and assemblies. This standard
More informationQuality Assurance Supplier Reference Guide
Quality Assurance Supplier Reference Guide Tel: (561) 840-1800 * Fax: (561) 844-8551 www.svmicrowave.com Table of Contents Page 1.0 Introduction 1 2.0 SV Drawing Format Interpretation 2 3.0 Inspection
More informationAPI 8 Round Connections
API 8 Round Connections Scope These guidelines apply specifically to the use of API 8RD (STC, LTC, EUE, NUE) connections. This document is based on API RP 5C1 which is the main document applicable for
More informationAPI Buttress Connections
IDM Code GDL00382/2 / March 2018 API Buttress Connections Scope These guidelines apply specifically to the use of API Buttress connections. This document is based on API 5C1 standard which is the main
More informationG.W. Lisk Co., Inc. Workmanship Manual DOC Rev 3
G.W. Lisk Co., Inc. Workmanship Manual DOC 09-09 Rev 3 PURPOSE: This documentation establishes the G.W. Lisk definitions, requirements, and inspection criteria for workmanship of machined parts and assemblies.
More informationQuality Assurance Supplier Reference Guide
Quality Assurance Supplier Reference Guide Tel: (561) 840-1800 * Fax: (561) 844-8551 www.svmicrowave.com 7/20/2015 Table of Contents Page 1.0 Introduction 1 2.0 SV Drawing Format Interpretation 2 3.0 Inspection
More informationSpecification for Threading, Gauging and Thread Inspection of Casing, Tubing, and Line Pipe Threads
Standard. It shall not be reproduced or circulated or quoted, in whole or in part, outside of API committee activities except with the approval of the Chairman of the committee having jurisdiction and
More informationLINEAR MEASUREMENT. Prof.H M Prajapati & Prof. A R Sankhla
LINEAR MEASUREMENT Introduction Classification Based on the type of standard Line measurement End measurement Based on precision Precise Direct: Vernier caliper, Micrometer Indirect: Telescopic gauge,
More informationPlumbing Part II - Hand Pump
Plumbing Part II - Hand Pump Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 7/17/03 Last Revised: 06/06/2004 The hand pump located in the tender water tank is a backup pump should the axel pump fail
More information. Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Wedge 513. Handling Plugs TN 9906.
Wedge 513 / 511 Connections Scope These guidelines apply specifically to the use of Wedge 513 and Wedge 511 connections. This document should be used in conjunction with the Running Manual which is the
More informationEvaluation Instructions Machining Level II CNC Milling
Evaluation Instructions Machining Level II CNC Milling General Instructions 1. Make sure that the candidate has his/her own copy of the part print, job instructions and understands the criteria for performance
More information. Recommended guidelines for the field inspection of TenarisHydril connections, FSOG Wedge 521. Handling plugs TN 9711.
IDM Code GDL00384/3 / March 2018 TenarisHydril Wedge 523 / 521 Connections Scope These guidelines apply specifically to the use of TenarisHydril Wedge 523 and Wedge 521 connections. This document should
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Brush Guard Kit Kit no. 67730 (black), 67731 (stainless) for GMC Trucks Your safety, and the safety of others, is very important. To help you make informed decisions about safety,
More informationOPERATING MANUAL SHOCK TOOL OWS WENZEL DOWNHOLE TOOLS LTD.
OPERATING MANUAL SHOCK TOOL OWS WENZEL DOWNHOLE TOOLS LTD. Release Notes: Release 2 Issued May 2016 Document # OM ST 001, Shock Tool Operating Manual Reviewed By: RG 1 P age OPERATING MANUAL SHOCK TOOL
More informationALERT SERVICE BULLETIN
January 28, 2010 TITLE INSPECTION OF MODEL 1A103/TCM PROPELLER HUB FOR CRACKING AND REWORK PROCEDURES TO: FAA-Approved Propeller Repair Stations, Cessna Aircraft Company, Aircraft Owners, and Operators
More informationWEAR SAFETY GLASSES WHEN INSTALLING THIS KIT.
INSTALLATION INSTRUCTIONS Trans4mer Mounting Systems Part No. 29753 (black) Part No. 65654 (stainless) for full size GM pickups, and Blazer, Yukon, Suburban, Tahoe As you read these instructions, you will
More informationPAGE 12 : THREAD MEASUREMENT TECHNIQUE (Plated and unplated thread gauges)
40-60 Delaware St. MACHINING Part No. PR301 - INDEX- MACHINING SECTION Revision: 01/12/2012 PAGE 1 This Quality Standard applies to all metallic parts unless otherwise specified by drawing or specification.
More informationGOST TUBING AND COUPLINGS
GOST 633-80 TUBING AND COUPLINGS Tubing is used for oil and gas production. Tubing shall be made seamless, plain- or upset end and couplings with high-seal connections. Coupling-free connections are possible.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 6367 For Chevrolet Silverado 1500, Suburban 1500 and Tahoe As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each
More informationMachinist s Guide to Toolholder Maintenance
Machinist s Guide to Toolholder Maintenance For Collet & Nut Style Toolholders General Overview Modern CNC machines feature high-capacity tool changers that automatically swap toolholders in and out of
More informationCoatings ASTM B117 SST Salt Spray Test Kesternick Phosphate Zinc E-Coat Dip Spin Coatings
Head and Thread types Coatings ASTM B117 Two major types of coating tests: SST Salt Spray Test screws are placed in a container and a salt solution is sprayed on the screws for a number of hours, checking
More informationMaster TAPERLOCK GAUGE BLOCK
Master Taperlock Fastener Gauge Kit Master TAPERLOCK Fastener Gauge Kit UTK-268002-27-4 KIT, Group 1 thru 4 UNITED S Master Taperlock Fastener Gauge Kit contains all of the required gauges and tools to
More informationStock Materials Interior Fillets... 10
Rapid Machining Overview... 3 Capabilities... 4 Certifications & Registrations... 4 Stock Materials... 5 Design Guidelines Tolerances... 6 Wall Thickness... 7 Outside Corners... 8 Hole Depth... 9 Interior
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 63470 For Ford 4x4 F150, F250 Light Duty & Expedition As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message
More informationSample Test Project. District / Zonal Skill Competitions. Skill- CNC Turning. Category: Manufacturing & Engineering Technology
Sample Test Project District / Zonal Skill Competitions Skill- CNC Turning Category: Manufacturing & Engineering Technology Version 1 Dec 2017 Skill- CNC Turning 1 Table of Contents A. Preface... 3 B.
More informationTrade of Toolmaking. Module 3: Milling Unit 9: Precision Vee Block Assembly Phase 2. Published by. Trade of Toolmaking Phase 2 Module 3 Unit 9
Trade of Toolmaking Module 3: Milling Unit 9: Precision Vee Block Assembly Phase 2 Published by SOLAS 2014 Unit 9 1 Table of Contents Document Release History... 3 Unit Objective... 4 Introduction... 4
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 76139 & 7643 For Chevrolet Silverado 1500 As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a
More informationTail Rotor Spindle Assembly Repair Procedure
Tail Rotor Spindle Assembly Repair Procedure Disassembly 1. Remove tail rotor assembly and blade assemblies in accordance with: a. TH28/480 Series MM-9-107 b. F-28F/280FX Series MM-10-2 2. Clamp spindle
More informationIX. FLARED JOINTS IX. FLARED JOINTS
IX. FLARED JOINTS IX. FLARED JOINTS While copper tube is usually joined by soldering or brazing, there are times when a mechanical joint may be required or preferred. Flared fittings (Figures 28 and 29)
More informationHow to Sharpen a Knife
How to Sharpen a Knife Even a good knife will lose some of its sharpness with time. However, sharpening a knife is easy if you have the right tool and know how to use it. Generally three different materials
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For GMC Sierra 2500HD & 3500, + 03 Kit 76248/76249 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 6334 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 7646 & 766 For GMC Sierra 500 As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a specific purpose.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Gen II Mount System For 2011-2012 Dodge Ram HD 4500/5500 Bracket Kit 90160 Your safety, and the safety of others, is very important. To help you make informed decisions
More informationCatalog October Speedi-Sleeve The quickest and most economical way to repair worn shafts
Catalog 457027 October 2005 Speedi-Sleeve The quickest and most economical way to repair worn shafts Table of Contents The Speedi-Sleeve concept...3 SPEEDI-SLEEVE, the quickest and most sensible way to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Gen II Mount System For 2008 Ford Super Duty Kit 80140 (Large Frame Black) and Kit 80150 (Mid Frame Black) and Kit 80155 (Mid Frame Stainless) Your safety, and the safety
More informationRigid Fluid Lines Tubing Materials Material Identification 7-1
Aircraft fluid lines are usually made of metal tubing or flexible hose. Metal tubing (also called rigid fluid lines) is used in stationary applications and where long, relatively straight runs are possible.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For 2007 Chevrolet Silverado 1500 and GMC Sierra 1500 Kit 75230 (Black) and 76007 (Stainless) Your safety, and the safety of others, is very
More informationMake a Safe. Description. Lesson Objectives. Assumptions. Terminology
Youth Explore Trades Skills Make a Safe Description Welding is a vast area in the metalworking field and a widely used joining process for metal. In this activity plan students will learn how to MIG weld
More informationPIONEER TRADING CO., LTD.
PRECISION KURODA LTD. OIL COUNTRY GAUGES API THREAD GAUGES PREMIUM CONNECTION GAUGES THREAD MEASURING INSTRUMENTS CONTACT TO: PIONEER TRADING CO., LTD. 4-1 Kuzuha-Asahi 3-Chome Hirakata Osaka 573-1111,
More informationHANDHOLE SEAT GRINDER
1041-1601 HANDHOLE SEAT GRINDER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 9/17/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,
More informationTwin screw and barrel are the heart of extruders and play very crucial role in extruder.
SHREE RADHEKRISHNA EXTRUSIONS PVT.LTD, a renewed engineering company has been Serving in the field of manufacturing screw & barrel for last more then 20 years. Radhekrishna Extrusions manufactures screw
More informationDESIGN GUIDE >> CNC MACHINING. Quotes in Hours. Parts in Days. rapidmanufacturing.com
Quotes in Hours. Parts in Days. rapidmanufacturing.com Contents 03 Overview 03 Capabilities 03 Certifications & Registrations 04 Stock Materials DESIGN GUIDELINES 04 Tolerances FINISHING 12 Threads 13
More informationFlat file. Round file. Hand file. Half -round. Mill file. Square file
Name Picture Cross section Uses: Cut pattern:: Hand file used for roughing and finishing. It has double cut teeth on two faces, single cut teeth on one edge, and one safe edge Flat file used for roughing
More informationKent Angle Frame Tree Pit
Kent Angle Frame Tree Pit Kent Angle Frame Tree Pit KATP1000/10 Specify: Kent Angle Frame Tree Pit KAFTP1000/100/10; 1000mm x 1000mm x 10mm; 100mm deep; Grade 316L Stainless Steel. Kent Stainless tree
More informationNAVSEA STANDARD ITEM
NAVSEA STANDARD ITEM FY-19 DATE: 01 OCT 2017 CATEGORY: I 1. SCOPE: 1.1 Title: Threaded Fastener Requirements; accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9086-CJ-STM-010/075, Fasteners 3. REQUIREMENTS:
More informationName: Machine Tool Technology ( )
Name: Machine Tool Technology (58.0501) Directions: Evaluate the student by checking the appropriate number to indicate the degree of competency. Rating Scale (0-6): 0 No Exposure no experience/knowledge
More informationCross Peen Hammer. Introduction. Lesson Objectives. Assumptions
Introduction In this activity plan students will develop various machining and metalworking skills by building a two-piece steel hammer. This project will introduce basic operations for initial familiarization
More informationTool and Die Maker Level 2
Level 2 B2 Read and Interpret Drawings II Duration: 32 hours 32 hours 0 hours This unit of instruction introduces the Tool and Die Maker Apprentice with the knowledge and skills necessary to read and interpret
More informationAction Frame Inspection and Repair. DEFINITIONS action spread vertical height differential rake
Action Frame Inspection and Repair DEFINITIONS action spread vertical height differential rake MAKING A FOOT PRINT mark the position of all action brackets, rails, and screws make screw hole spacing template
More informationCutting, Grinding and Abrasive Accessories
High quality range of abrasive cutting discs, grinding discs and surface preparation accessories engineered for ultimate performance Universal Diamond Blades Cutting and Grinding Discs The essential construction
More informationTroubleshooting for Milling Chuck. Details of the trouble Cause Solution / Countermeasures
TROUBLESHOOTING 571 Troubleshooting Troubleshooting for Milling Chuck Details of the trouble Cause Solution / Countermeasures Tool cannot be held Tool shank diameter should be within h7 tolerance. Tool
More informationEvaluation Instructions Machining Level II Milling: Precision Locations
Evaluation Instructions Machining Level II Milling: Precision Locations General Instructions 1. Make sure that the candidate has his/her own copy of the part print, job instructions and understands the
More informationSplitcase - firefighting Pump
APPLICATION REPORT Splitcase - firefighting Pump Application: Place: Rebuilding and protection of Splitcase firefighting Pump Assens Shipyard - Workshop Date: September 2007 Job and report done by: Wencon
More informationScraping Plane 05P29.01
Scraping Plane 05P29.01 U.S. Pat. No. 7,444,750 The Veritas Scraping Plane is used for the final levelling and smoothing of large, flat surfaces, even if they are highly figured, prior to applying a finish.
More informationWire and pipe drawing
Wire and pipe drawing Overview Wire drawing application deformations, drawing speeds and forces equipmentm dies and die materials Tube drawing tube drawing processes Strain and drawing force Drawing tools
More informationKent Waterford Recessed Tree Pit
Kent Waterford Recessed Tree Pit Specify: Kent Waterford 1200mmx 1200mm x 106mm; Grade 316L Stainless Steel. The Kent Waterford is manufactured from Grade 316L Stainless Steel. The external finish of the
More informationlimiting factor on the thread type used.
1 Definition The diameters, threads per inch (TPI) and thread pitch, etc. are necessary to completely identify a thread. In a shop, specialty gauges are required to accurately gauge or identify threads.
More informationSTUDY ON DIES FOR WOOD PELLET MACHINES
STUDY ON DIES FOR WOOD PELLET MACHINES Definition of pellet dies Pellet die can be simply defined as a metal part with holes, either flat or ring-shaped, in which the roller forces raw material under intense
More informationSheet Metal Tools. by:prem Mahendranathan
Sheet Metal Tools by: SHEET METAL TOOL KIT SHEET METAL TOOLS Rivet Gun 3/32, 1/8, 5/32, 3/16",Cupped Set Mini Bucking Bar Footed Heel-Toe Bucking Bar Air Tool Oil Mechanics Tool Bag High-Speed Air Drill
More informationLOCATING PINS AND HOW THEY ARE USED. Chris Blaszczyk, Manager of Product Development, MISUMI USA
LOCATING PINS AND HOW THEY ARE USED Chris Blaszczyk, Manager of Product Development, MISUMI USA Editor Note: This article reviews the various types of locating pins available for machine designers and
More informationScraping Plane 05P29.01
Scraping Plane 05P29.01 Patent Pending The Veritas Scraping Plane is used for the final levelling and smoothing of large, flat surfaces, even if they are highly figured, prior to applying a finish. Because
More informationFACULTY OF ENGINEERING DESIGN AND PRODUCTION ENGINEERING DEPARTMENT. Credit Hour System Metrology Lab 1 MDP 240 (1) Fixed gauges. Metrology laboratory
FACULTY OF ENGINEERING DESIGN AND PRODUCTION ENGINEERING DEPARTMENT Report On: Credit Hour System Metrology Lab 1 MDP 240 (1) Fixed gauges Metrology laboratory Class No: B.N. Student Name Remark Signature
More informationMechanical Actuators
Mechanical Actuators Rotating Machine Screw Actuators 2-Ton and Larger Capacity Installation, Operation & Maintenance Instructions Publication Part No. SK-2389-R CAUTION This manual contains important
More informationGeneral Bearing Corporation
General Bearing Corporation General Bearing Corporation GBC: We are Customer Driven. In 1943, General Bearing Corporation (GBC) began production as a manufacturer of highly-specialized bearings, bushings,
More informationwebsite:
Phone: 1-800-882-0008 (U.S.) Phone: 1-866-832-6753 (Canada) Phone: 1-847-742-7840 (International) Fax: 1-800-526-7268 (U.S. & Canada) Fax: 1-847-742-0261 (International) e-mail: info@skf.com website: http://www.skf.com
More information7-1
Tube Cleaning Brushes Fitting Cleaning Brushes available with wire or plastic handle Fitting Cleaning Brushes clean the inside of fittings faster. For plumbing or refrigeration applications. Carbon steel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Winch Mount For 2007-2010 Chevrolet Silverado HD and GMC Sierra HD Bracket Kit 90140 Your safety, and the safety of others, is very important. To help you make informed
More informationACCREDITATION FACILITY AUDIT CHECKLIST
ACCREDITATION FACILITY AUDIT CHECKLIST Institution Name: Date: Designated Trade: Machinist AC #: Contact: Location: Course Duration: of weeks: of hours total: of hours per day: Instructor(s) of Students
More informationRepair of Rotac Actuators
Repair of Rotac Actuators MP Model OVERHAUL INSTRUCTIONS Also Includes older styles RN CG XL HN Read the entire contents of these instructions before installing the actuator and before making any connections
More informationTHERE IS MEASURE IN ALL THINGS.
III-1 (77) III. METROLOGY THERE IS MEASURE IN ALL THINGS. HORACE SATIRES, BOOK I, 35 B.C. III-2 (78) III. METROLOGY II.A INTRODUCTION Metrology Metrology is presented in the following major topic areas:
More informationSurface Finishes. For woods metals and plastics
Surface Finishes For woods metals and plastics Reasons for Surface Finishes Some kind of surface finish is always necessary for the following reasons Resistance to decay (Stopping the material from rotting
More informationASSIGNMENT 2. Textbook Assignment: 2-1. Levels are designed for which of the following purposes?
ASSIGNMENT 2 Textbook Assignment: "Levels," "Plumb Bulbs," "Scribers," "Squares," "Surface, Depth, and Height Gages," "Ring and Snap Gages and Gage Blocks," "Miscellaneous Measuring Gages," "Pliers and
More informationAve Edmonton, AB Canada T6P 0E2 Ph: Fax: apachepipe.com world class world wide
PIG OPTIONS 7-1 Model BB Flat Model BB Pencil Model RB 6-14 Flat Model RB 16-48 Flat Model HDPE 3-16 Pencil Model RB 16-48 Pencil 7-2 Model XB Pencil Model XB Flat Model XB Nylon Model XB Cantilever Assembly
More informationGeneral Machining, Fitting and Assembly Applications A/508/5164
Unit Title Ofqual unit reference number (code) Organisation Reference General Machining, Fitting and Assembly Applications A/508/5164 QU051773 Unit Level Level 2 Unit Sub Level None GLH 55 Unit Credit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Mounting System Dodge Ram Kit No. 65220, 73132, 75525, 76253 (black) or 65221, 73133, 75530, 76254 (stainless) As you read these instructions, you will see NOTES, CAUTIONS
More informationHOME WORKSHOP HANDBOOK Rugged BENCH GRINDER. By JOEL B. LONG
6 HOME WORKSHOP HANDBOOK Rugged BENCH GRINDER W By JOEL B. LONG ITH this bench grinder you can keep your cutting tools sharp and do general offhand grinding, and can, with the aid of various attachments,
More informationAluminum Crack Repair. Without Welding
Aluminum Crack Repair Without Welding Topics Crack detection/inspection Metal stitching Threaded hole repair Crack Detection Visual Pressure testing Dye-penetrant Visual Practiced by many as the only way
More informationEvaluation Instructions Machining Level II CNC Turning
Evaluation Instructions Machining Level II CNC Turning General Instructions 1. Make sure that the candidate has his/her own copy of the part print, job instructions and understands the criteria for performance
More informationBIPPMM03 (Published) Book specs- Dates: / / Lang: ENG01 Applic: PPM
BIPPMM03 (Published) Book specs- Dates: 20060412 / 20060412 / 20060412 Lang: ENG01 Applic: PPM Installing the Milnor Diaphragm in the Single Stage Press This document applies to models MP160Axx, MP1604xx,
More information26. TenarisHydril Blue Riser Connection
IDM Code GDL 00368/2 / November 2015 26. TenarisHydril Blue Riser Connection Scope These guidelines apply specifically to the use of TenarisHydril Blue Riser connections. This document shall be used in
More informationGeneral machining, fitting and assembly applications
Unit 065 General machining, fitting and assembly Level: 2 Credit value: 12 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required to cover a
More informationAFB (AIR FAN BEARING) INSTALLATION GUIDE
654 AFB (AIR FAN BEARING) INSTALLATION GUIDE AFB PARTS Bearing Housing - Secured together with two 3/8 x 1.25 in. Cap Screws Black Wiper Seals - Secured together with O-ring cord (Subsequently depicted
More informationVarious Bolt Removal Process
Various Bolt Removal Process Introduction I have been climbing for over 25 years. The first bolt I placed in 1987 was a 5/16 Rawls carbon steel, split shank, button head in sandstone. Certainly the wrong
More informationVarious Bolt Removal Process
Various Bolt Removal Process Introduction I have been climbing close to 30 years. The first bolt I placed in 1987 was a 5/16 Rawls carbon steel, split shank, button head in sandstone. Certainly the wrong
More informationSession 10 Dimensions, Fits and Tolerances for Assembly
Session 10 Dimensions, Fits and Tolerances for Assembly Lecture delivered by Prof. M. N. Sudhindra Kumar Professor MSRSAS-Bangalore 1 Variations in Production It is necessary that the dimensions, shape
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More informationModule-2 Lecture-1 Angle plate, steel rule, spring calipers. (Refer Slide Time: 00:14)
Metrology Prof. Dr. Kanakuppi Sadashivappa Department of Industrial and Production Engineering Bapuji Institute of Engineering and Technology-Davangere Module-2 Lecture-1 Angle plate, steel rule, spring
More informationManufacturing Workmanship Standards. KSO Rev 1
Manufacturing Workmanship Standards KSO Rev 1 This document is a statement to the quality and workmanship by Kso Metalfab, Inc. The definitions, procedures, and responsibilities contained in this Workmanship
More informationPerformance Standards Benchwork
Performance Standards Benchwork Materials A block of cold rolled mild steel 1.00 x 2.00 x 3.00 milled or filed to length (see Duties and Standards for Machining Skills Level I, September 2001) or as specified
More informationRecommended Dimensional Guidelines for Single Screws
The Society of the Plastics Industry s Machinery Component Manufacturers Division Recommended Dimensional Guidelines for Single Screws The following recommendations for single screws of injection molding
More informationRestoring a Bulle Clock. Restoration of Bulle Clock Serial Number
Page 1 Restoration of Bulle Clock Serial Number 12199. Page 2 This clock is the subject of the restoration with kind permission of the owner. The photo shows the clock as received. The door has been retained
More informationWater Line and Water Line Assembly Gasket
1 Preparation for Repair 1) Remove tip from scaler 2) Remove scaler from air supply 3) Remove gasket from back end of scaler. Examine gasket for obvious wear or disfigurement. Replace if necessary. 2 Remove
More informationDETAIL SPECIFICATION SHEET NUT, TUBE, BULKHEAD AND UNIVERSAL FITTING
INCH-POUND AN924 Rev 13 14 April 2014 SUPERSEDING AN924 Rev 12 w/amendment 1 23 January 2013 DETAIL SPECIFICATION SHEET NUT, TUBE, BULKHEAD AND UNIVERSAL FITTING Reinstated after 14 June 2012. Inactive
More informationWARNING. Failure to observe these instructions could lead to severe injury or death.
INSTALLATION INSTRUCTIONS WINCH MOUNTING KIT Part Number: 80156, 80160 Application: 2008 Ford F150 Your safety, and the safety of others, is very important. To help you make informed decisions about safety,
More informationPrecision glassware made by SCHOTT
SCHOTT MEDICA GMBH INDUSTRIAL GLASS µ m µ µ Precision glassware made by SCHOTT Tubes and capillaries made of DURAN at highest precision µ Precision...... in glass SCHOTT Medica GmbH in Wertheim, a subsidiary
More informationMaterials Needed. Tube Size O.D.
Materials Needed Eaton FF9075 silver braze rings or 1/16- inch diameter 45% silver alloy braze wire Water soluble flux Brazing outfit capable of +1200ºF (propane or mapp gas) Small files - rattail and
More informationEXPERIMENT 1 TO CHECK WHETHER THE MEASURING INSTRUMENTS ARE ACCURATE, PRECISE OR BOTH.
EXPERIMENT 1 TO CHECK WHETHER THE MEASURING INSTRUMENTS ARE ACCURATE, PRECISE OR BOTH. Aim 1: To check whether the given Vernier Caliper is accurate, precise or both. Objective: Students will be able to
More information