MVR Molded Vacuum Reclosers. Instruction Manual

Transcription

1 MVR Molded Vacuum Reclosers Instruction Manual

2 2Section 1: Overview Introduction Elastimold MVR Molded Vacuum Reclosers Thank you for your purchase of the Elastimold Molded Vacuum Recloser (MVR). This state-of-the-art recloser incorporates several design features that will assure you of many years of reliable, trouble-free service. Features and innovations include: A lightweight, maintenance-free, fully modular design allowing individual pole replacement or shed replacement in the event of external damage Specially formulated molded EPDM main body with overlapping silicone sheds for improved dielectric, weatherability and UV performance Integral CT and load-side voltage sensors with option to add source-side voltage sensors Electrically linked operation so singlephase trip provides three-phase lockout with mechanically linked manual trip mechanism Highly visible position indicator Fully solid-dielectric design incorporating unique diaphragm technology to isolate high voltage from the grounded housing State-of-the-art magnetic actuator mechanism

3 Table of Contents Elastimold SECTION 1: Overview Introduction Ordering Information...4 Ratings and Specifications...4 Description of Operation The single-phase Elastimold MVR is controlled and operated by the SEL 351RS Kestrel control via a 10-pin interconnecting cable. The three-phase Elastimold MVR can be controlled either directly with the SEL 651Rx2 control via a 32-pin interconnecting cable or by a SEL 351R or 351R Falcon control via a 14-pin cable connected to an MVR power module, which then connects to the recloser. This manual will cover the set-up and installation of your new Elastimold MVR Recloser. For information on SEL controls and their operation, please refer to their respective manuals. SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc. SECTION 2: Instruction Manual and Drawings Elastimold MVR Single-Phase and Three-Phase Instruction Manual Safety Instructions...5 Acceptance and Inspection...6 Lifting...6 Set-Up and Mounting Voltage Sensor Set-Up...10 Grounding and Testing Operation and Maintenance...12 Outline Drawings Single-Phase 15/27kV 3188C Single-Phase 38kV 3188C Three-Phase 15/27kV 3188C Three-Phase 38kV 3188C Schematic Drawings Single-Phase 15/27/38kV 3188C Three-Phase 15/27/38kV 3118C Power Module (for use with SEL 351R) 3118C SECTION 3: Design Test Data Elastimold MVR Test Data Summary

4 4Section 1: Overview Ordering Information/Ratings and Specifications Molded Vacuum Recloser Catalog Numbering System 1 Notes: X X X X X Phase 1 = One Phase 3 = Three Phase MVR = 15kV Class 27 = 27kV Class 38 = 38kV Class 3 12 = 12.5 ka - = Future Source-Side 651Rx2, SEL 351R or SEL 351R or SEL Ratings and Specifications 4 = No 1 = One Voltage Sensor 3 = Three Voltage Sensors 5 1 = SEL 351R, SEL 351R Falcon (14-Pin Connector) 2 = SEL 651R (32-Pin Connector) 3 = SEL 351RS Kestrel (Single- Phase MVR Only) Description 15kV 27kV 38kV* Nominal System Voltage (kv RMS) Rated Maximum Voltage (kv RMS) Nominal Frequency (Hz) 50 or or or 60 Phase Spacing on 3-Phase Units (Inches) BIL (kv) Power Frequency Withstand Dry (kv) Power Frequency Withstand Wet (kv) Continuous Current (A RMS) Eight-Hour Overload Current (A RMS) CT Ratio 1000 to to to 1 Interrupting Current (ka RMS Symmetrical) Making Current (ka Asymmetrical Peak) Creepage Distances Inches (Line to Ground) Arc-Extinction Medium Vacuum Vacuum Vacuum Insulation Medium EPDM/Silicone Rubber EPDM/Silicone Rubber EPDM/Silicone Rubber Mechanical Operations 10,000 10,000 10,000 Operating Temperatures -40º C to 65 º C -40º C to 65 º C -40º C to 65 º C Voltage Sensor Accuracy (Load/Line) 3% / 1% 3% / 1% 3% / 1% CT Accuracy Class 1 Class 1 Class 1 Weight (Single-Phase/Three-Phase) 57/208 lbs. 57/208 lbs. 58/211 lbs. SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc. Notes: Sequential Numbers Controls Control Type 1-Phase 3-Phase SEL 351RS Kestrel 10-pin cable X SEL 351R X 14-pin cable SEL 651RX2 X 32-pin cable Notes:

5 Instruction Manual Safety Instructions The following are general caution and warning statements that apply to this equipment. Additional statements related to specific tasks and procedures are located throughout this manual. WARNING: CAUTION: WARNING: Before installing, operating, maintaining or testing this equipment, carefully read and understand the contents of this manual. Improper operation, handling or maintenance can result in death, severe personal injury or equipment damage. WARNING: Hazardous voltage. Contact with high voltage will cause serious personal injury or death. Follow all locally approved safety procedures when working around high-voltage lines and equipment. WARNING: Hazardous voltage. Do not rely on the contact position indicator to determine that the line has been de-energized. Always establish a visible disconnect and establish person grounds when performing de-energized line work. Failure to follow proper safety practices can result in contact with high voltage, which can cause death or severe personal injury. WARNING: Hazardous voltage. Recloser and control must be solidly grounded. Improper grounding can result in contact with high voltage, which will cause severe personal injury or death and equipment damage. Disconnecting the control cable when the recloser is energized could result in high voltage on the pins if the recloser tank is not grounded as specified. WARNING: When testing at high voltage, the MVR and high-voltage test equipment should be in a test cage or similar protective area to prevent accidental contact with the high-voltage parts. All equipment needs to be solidly grounded. Failure to comply can result in death, severe personal injury and equipment damage. CAUTION: All MVRs are sealed and leak tested prior to shipment to prevent moisture ingress. Do not open the lower cover as it is possible that the MVR will not reseal when the cover is closed. While the diaphragm will keep moisture from ever entering the high-voltage chamber, excessive moisture ingress could cause damage to the magnetic actuator mechanism and misoperation. CAUTION: Do not remove and replace the side terminal in the field. The MVR incorporates a unique diaphragm technology that fully encapsulates the high-voltage chamber in the MVR. The side terminal must be vented during installation and then sealed to prevent pressure build-up against the diaphragm during the installation process. Improper installation may cause equipment damage and possible personal injury. CAUTION: Rotating the terminal connector without properly loosening the connector will apply excessive force on the terminal stud and could damage the interrupter assembly. CAUTION: The complete recloser system, including control, requires routine inspection and maintenance if damage is found to ensure proper operation. If it is not maintained, it may fail to operate properly. Improper operation may cause equipment damage and possible personal injury. CAUTION: Follow approved safety practices when lifting and mounting the MVR. Use lifting rings on three-phase units and lift smoothly, limiting shifting to avoid damage. Do not lift three-phase MVRs by the side terminals as damage could result. CAUTION: Do not energize the recloser for service until all control settings have been properly programmed and verified. Refer to the appropriate SEL control manual for programming procedures. Failure to comply may result in control and recloser misoperation. These instructions are not intended to cover all details or variations in the equipment, procedures or processes described. Nor are they designed to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for the user s purpose, please contact your local Thomas & Betts representative. SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc. 5

6 6 Instruction Manual Acceptance and Initial Inspection Each MVR is shipped completely assembled, pretested and in the closed position from the factory. Upon arrival, uncrate the unit (refer to Crate Removal and Visual Inspection section). Check the unit does not have missing parts and it is in the closed position. Also check the unit for any damage that may have occurred during shipping. Should any damage be found, file a claim with the shipping carrier and contact the factory or your local Thomas & Betts representative. Crate Removal and Visual Inspection Packaging may differ depending on the units being shipped. Carefully remove the MVR from its packaging. In the case of units shipped in crates, remove the outer crate top by removing the screws or bolts attaching it to the skid. Then unbolt the recloser from the skid. It is then possible to lift the unit directly off the skid with a hoist. Take care when opening packaging not to nick or cut the EPDM/silicone insulation on the MVR. After uncrating, visually inspect the MVR for any shipping damage, including the insulation, bushings, trip lever, mounting frame, etc. If damage has occurred, please file a claim with the shipping carrier immediately and contact your local Thomas & Betts representative. Do not attempt to install the equipment with damages or missing parts. Lifting Single-phase units can be lifted and moved by hand or by fastening a loop around the main body. Three-phase units must be lifted using the lifting rings. Follow all approved safety practices when making hitches and lifting the equipment. Lift the MVR smoothly by using the four lifting rings on the recloser as shown. Do not allow the unit to shift. Be careful that the lifting sling exerts no forces on the side terminals or on the individual poles. Lifting Rings Four Lifting Ring Detail CAUTION: Follow approved safety practices when lifting and mounting the MVR. Use lifting rings on three-phase units and lift smoothly, limiting shifting to avoid damage. Do not lift three-phase MVRs by the side terminals as damage could result.

7 Set-Up WARNING: Before installing, operating, maintaining or testing this equipment, carefully read and understand the contents of this manual. Improper operation, handling or maintenance can result in death, severe personal injury or equipment damage. Set-up and testing of the recloser can be performed at maintenance facilities, test laboratories or directly in the field once appropriate control supply voltage is made available. Connect the recloser to the appropriate control: Single-phase units the MVR should be connected to the SEL 351RS Kestrel control via a 10-pin interconnecting cable SEL 651Rx2 control the MVR should be connected to the control via a 32-pin interconnecting cable SEL 351R or 351R Falcon control the 14-pin cable should be connected to the MVR power module, and the 6-ft. 32-pin cable should be used to connect the power module to the MVR* The recloser receives the necessary signal to open and close from the control circuitry. The control is powered from an external supply voltage but is also supplied with a battery backup system that is fully charged from the factory. The battery backup system, located in the control cabinet, is shipped in the off or disconnected position. For information on how to connect the battery, please refer to the appropriate SEL control manual. Pole Ground System Neutral Control Cable Protective Shield around Pole Ground Line PT LINE NEUTRAL GROUND POWER MODULE Recloser Control GROUND CONTROL SUPPLY Utility Pole Typical Installation Detail Recloser 351R and 351R Falcon only; Cable Plugs Directly into Recloser on 351RS Kestrel and 651R Arresters The figure at right shows a typical recloser, control and power supply interconnection layout. SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc. 7

8 8 Instruction Manual Mounting Note: Use extreme care in handling the recloser so that no force is exerted on the side terminals or on the individual poles as damage may result. Attach the mounting bracket to the pole or structure using a 3 4" lag or thru bolt (customer supplied). Hoist the MVR by creating a sling around the main body and the side terminal on the recloser, and lower it into the mounting bracket. Orient as desired and then lock in place by torquing the two 3 8"-16 set screws to 20 ft.-lbs. The singlephase recloser can be oriented from 0 to 180 degrees as shown at right. Hoist the MVR by creating a sling that uses the lifting rings provided on the recloser. Mount the recloser on the pole or structure using two 3 4" lag or thru bolts (customer supplied) as specified on the product drawings shown on and 19. With the SEL 351R or 351R Falcon control, mount the power module onto the pole below the recloser, as shown at right. With the SEL 651R control, no power module is needed and the 32-pin cable should be plugged directly into the recloser. CAUTION: Follow approved safety practices when lifting and mounting the MVR. Use lifting rings on three-phase units and lift smoothly, limiting shifting to avoid damage. Do not lift three-phase MVRs by the side terminals as damage could result. High-Voltage Terminations The terminal connectors supplied with each recloser are aluminum alloy with standard NEMA two-hole drilling and the bolts/nuts are silicon bronze. The electrical connection at the terminal pad must be treated with Alcoa No. 2 joint compound or equivalent. Each terminal should be wire brushed through the compound to improve the connection. If the terminal pad is rotated, the connector bolt(s) must be loosened before turning the pad. Retighten the bolt(s) to 25 ft.-lbs. after repositioning. CAUTION: Rotating the terminal connector without properly loosening the connector will apply excessive force on the terminal stud and could damage the interrupter assembly. SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc. 14-Pin 14 PIN CABLE Cable Single-Phase Orientations 180 Three-Phase Mounting Torque to 25 ft.-lbs. Loosen prior to repositioning. High-Voltage Terminal Connectors 3232-Pin PIN CABLE Cable Power module used with 351R and 351R POWER Falcon MODULE only. When USED WITH using 351R a 651R, ONLY. the WHEN 32- USING pin cable A 651R, is connected THE 32 P CABLE directly IS to CONNECTED the recloser. D TO THE RECLOSER.

9 Surge Arrester Mounting Each single-phase recloser mounting ring has a provision for mounting an optional bracket on either side of the recloser to support two customer-supplied arresters (one line-side and one load-side). Refer to the supplied recloser drawings for specific installation dimensions. Alternate configurations are shown at right. Three-phase reclosers have provisions for mounting an optional front bracket to support three load-side, customer-provided surge arresters. A rear mounting bracket for three additional line-side arresters is also available as an option as well as an option to mount multiple transformers. Refer to the supplied recloser drawings for specific installation dimensions. See example at right. LINE Line ARRESTOR Arrester LOAD Load ARRESTOR Arrester Line Arrester Line LINE ARRESTOR Arrester Single-Phase Surge Arrester Mounting Since arresters are designed to provide lightning overvoltage protection, they should be mounted as close as practical to the recloser if the standard arrester brackets are not used. Control Wiring Control power must meet the requirements stated on the drawings supplied with the recloser control. Please refer to the appropriate SEL control manual. Each recloser and control cabinet assembly comes with standard interconnection cables that are keyed at each end to assure proper installation. Please see figures below for descriptions of the receptacle pins. Load Arrester Three-Phase Surge Arrester Mounting D E F C D A T B S C U V e R W f d P g j X c N h Y b M Z a G L H J K 651Rx2 A B K L J M P H N E G F 351R A CT AØ H NOT USED R VLINE CØ Y CLOSE AØ f CLOSE BØ B CT BØ J VLOAD AØ S VNEUTRAL Z TRIP AØ g TRIP BØ C CT CØ K VLOAD BØ T NOT USED a NOT USED h CLOSE CØ D CT NEUTRAL L VLOAD CØ U MONITORED TRIP AØ (52a) b NOT USED j TRIP CØ E NOT USED M VNEUTRAL V MONITORED TRIP BØ (52a) c NOT USED F 12VDC N VLINE AØ W MONITORED TRIP CØ (52a) d NOT USED G GND P VLINE BØ X MONITORED MANUAL TRIP (69) e NOT USED A 24VDC F MONITORED CLOSE PT L NOT USED B MONITORED TRIP PT G CT AØ M GND C TRIP H CT BØ N CAP HEALTHY STATUS (OPTIONAL) D MONITORED TRIP PT J CT CØ P CAP HEALTHY STATUS (OPTIONAL) E CLOSE K CT NEUTRAL A MONITORED TRIP (52a) B A H F NOT USED B MONITORED MANUAL TRIP (69) G GND C J K G C CT H 12VDC D E F D CT NEUTRAL J TRIP 351RS Kestrel E NOT USED K CLOSE SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc. 9

10 Instruction Manual Grounding To ensure the maximum amount of protection for internal control components during possible power surge events, the recloser and control cabinet need to be solidly grounded together. The recloser ground conductor must be connected to the supplied #10 2 AWG ground lug located on the recloser s frame base. All separate grounds should be connected to the main ground wire. All connections to the SEL control (including the control cable, which contains a ground) must be routed in close proximity to and parallel to the main ground paths and should be approximately equal in length. When using a power module with a 351R or 351R Falcon, the power module box must also be grounded. See Set-Up on for a visual representation. Electronic Operation Test Using the controller, open and close the MVR electrically by pressing the marked open and close buttons. Confirm that the selected button is in agreement with the position indicator on the control panel as well as the recloser position indicator. The recloser position indicator is located on the bottom of the recloser as shown below. MVRs are designed to operate with a total circuit resistance of ohms across the TRIP/CLOSE pins on the SEL control interface. Open Position Closed Position WARNING: Hazardous voltage. Recloser and control must be solidly grounded. Improper grounding can result in contact with high voltage, which will cause severe personal injury or death and equipment damage. Disconnecting the control cable when the recloser is energized could result in high voltage on the pins if the recloser tank is not grounded as specified. Closed Position Individual Pole Position Indicator (Side View) Open Position Individual Pole Position Indicator (Bottom View) Voltage Sensor Set-Up All Elastimold MVRs come with pre-calibrated, loadside capacitive voltage sensors that are capable of measuring amplitude and phase angle with an accuracy of approximately 3% under normal operating conditions (-10 C to 45 C) and +/-5% at extreme conditions (-40 C to 65 C). For 3-phase MVRs, optional pre-calibrated line-side resistive voltage sensors are also available and are capable of measuring the voltage with a higher accuracy of approximately 1%. All sensors require an 8VAC LEA voltage sensor input on the SEL 651Rx2 control. Refer to the Elastimold Source Side Voltage Sensor (ESSVS) Installation Instructions for mounting details. The ESSVS are not used with the SEL 351R, 351R Falcon or 351RS Kestrel Controls. CAUTION: Do not energize the recloser for service until all control settings have been properly programmed and verified. Refer to the appropriate SEL control manual for programming procedures. Failure to comply may result in control and recloser misoperation. WARNING: Hazardous voltage. Do not rely on the contact position indicator to determine that the line has been de-energized. Always establish a visible disconnect and establish grounds when performing de-energized line work. Failure to follow proper safety practices can result in contact with high voltage, which can cause death or severe personal injury. 10 SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc.

11 Manual Trip Lever Test With the switch closed, pull down the yellow trip lever as shown in center photo at right and verify that the recloser opens. The position indicators located on the bottom of the recloser will be GREEN for OPEN. The manual trip lever will remain in the down position until returned to the up position. When in the down TRIPPED position, the manual trip will block all close operations until it is manually restored to the up NORMAL position. When using the standard SEL 651Rx2, the control standard settings will also send a signal to open when the manual trip handle is pulled. The recloser can be closed once the manual trip handle has been restored to the normal position by pressing the close button on the control. Vacuum Interrupter Tests Closed Position Manual Trip Lever Closed Position Every recloser is quality checked and tested before leaving the factory to assure it meets all design specifications. In order to verify proper operating condition after shipment and before installation, two tests should be performed to evaluate the vacuum contacts. These tests should be performed across each module separately and can be performed again, as desired, throughout the life of the recloser. Open Position WARNING: When testing at high voltage, the MVR and high-voltage test equipment should be in a test cage or similar protective area to prevent accidental contact with the high-voltage parts. All equipment needs to be solidly grounded. Failure to comply can result in death, severe personal injury and equipment damage. Loss of vacuum results in complete breakdown across open vacuum contacts at voltages below 30kV RMS. Only AC high potential testing is meaningful. With the recloser in the OPEN position, apply 30kV RMS across each individual contact for 15 seconds. To avoid possible generation of X-rays, do not apply more than 30kV RMS. During the high potential testing, self-extinguishing, momentary breakdowns lasting only a few seconds may occur. These breakdowns are not significant but can result in false indication of vacuum loss if the test set uses a high-speed overload relay or breaker. During normal operation with the recloser in service, loss of vacuum or a defective module may be indicated by excessive AM radio noise with the recloser open or by measuring a difference in surface temperatures (differential of more than 5º C temperature rise above normal ambient) between poles on the same recloser. When loss of vacuum occurs, contact resistance will typically increase. Test Equipment Load Contact Manual Trip Lever Open Position Line Contact With the recloser in the CLOSED position, measure the resistance across each module. Resistance values should be less than 200 micro-ohms. If higher resistance values are measured, contact your local Thomas & Betts representative. Test Cable Set-Up Details SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc. 11

12 Instruction Manual Operation The recloser receives the necessary signal to open and close from the control circuitry. For specific information concerning the operation of the control and how to change settings, please refer the appropriate SEL control manual. When using standard SEL settings files, the CT ratio will already be preset to 1000:1 and the voltage sensors will come pre-calibrated (used on the 651Rx2 only). If standard settings files are not used, the CT input in the SEL control will need to be adjusted to 1000:1. All voltage sensors require an 8VAC LEA input and are pre-calibrated to a ratio of 10kV on the line to 1VAC into the SEL control. For specific information on how to adjust settings and curves, please refer to the appropriate SEL control manual. Note that certain SEL controls limit the number of reclose sequences when AC or battery is not present. Please consult Schweitzer Engineering Laboratories. For specifications, please refer to the Power Module Box Installation and Operation Instructions. Maintenance CAUTION: The complete recloser system, including control, requires routine inspection and maintenance if damage is found to ensure proper operation. If it is not maintained, it may fail to operate properly. Improper operation may cause equipment damage and possible personal injury. The Elastimold MVR is designed to be maintenance free under normal operating conditions, and the EPDM/silicone insulation is not prone to the cracking or chipping that sometimes occurs with porcelain or epoxy insulators. However, should damage occur as a result of an external event, in most cases it is possible to replace the damaged components due to the modular design of the recloser. Both the top and bottom silicone shed, as well as the side terminal, can be removed and replaced if damaged by external arcing, a knife cut, etc. If damage extends to the main body of the pole, the pole in each phase can be replaced individually. If damage occurs, please contact Thomas & Betts customer service. If it becomes necessary to clean the main body or sheds, recommended cleaning agents are soap and warm water or isopropyl alcohol. CAUTION: All MVRs are sealed and leak tested prior to shipment to prevent moisture ingress. Do not open the lower cover as it is possible that the MVR will not reseal when the cover is closed. While the diaphragm will keep moisture from ever entering the high-voltage chamber, excessive moisture ingress could cause damage to the magnetic actuator mechanism and misoperation. CAUTION: Do not remove and replace the side terminal in the field. The MVR incorporates a unique diaphragm technology that fully encapsulates the high-voltage chamber in the MVR. The side terminal must be vented during installation and then sealed to prevent pressure build-up against the diaphragm during the installation process. Improper installation may cause equipment damage and possible personal injury. TOP Top SHED Shed SIDE Side TERMINAL Terminal BOTTOM Bottom Shed SHED 12 SEL is a registered trademark of Schweitzer Engineering Laboratories, Inc. Standard Pole Replacement Details

13 Outline Drawings Single-Phase 15/27kV 3188C0110 DRAWING NUMBER REV [255,6] 6) CREEPAGE DISTANCE: LINE TO GROUND = 41.50" [1054] LOAD TO LINE = 52.00" [1321] 7) INTERRUPTER RATING = 12.5 KA 8) BIL: LINE TO GND = 150KV LINE TO LINE = 150KV NOTES: 1) DIMENSIONS IN BRACKETS [XXX] ARE MILLIMETERS. 2) MAXIMUM CANTILEVERED TERMINAL PAD LOAD OF 60 LBS. [27 KG.] PER PAD ALLOWABLE. HORIZONTAL CABLE TENSIONS PER PHASE TO BE OPPOSITE IN DIRECTION. 3) WEIGHT= 57 LBS. [25.8 KG.] 4) STANDARD POSITION AS SHOWN. TRIP POSITION SHOWN DOTTED. 5) CONNECTION OF THE RECLOSER TO THE DESIGNATED LINE AND TERMINALS IS ONLY REQUIRED IF THE RECLOSER IS BEING USED WITH A CONTROL CONTAINING DIRECTIONAL OVER CURRENT CAPABILITY [70,3] [328,5] CABLE CONNECTION PROVISION [746,2] OPEN - GREEN BLACK CLOSED - RED BLACK OPEN/CLOSE INDICATOR LINE SIDE (SEE NOTE 5) 1.75 [44,5] RECLOSER (SEE NOTE 5) [609,3] [890,2] 8.64 [219,4] CLEARANCE SLOT FOR USER SUPPLIED 5/8[16] DIA LAG OR THRU BOLT [498] ENGINEERING SPEC. QUALITY STD. MATERIAL STD. MANUAL TRIP HANDLE SEE NOTE 4 ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION 3/8-16 BOLT FOR SECURING RECLOSER TO FRAME INCH mm ENGLISH METRIC DUAL INCH mm x MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH OPEN/CLOSE INDICATOR (SEE VIEW) DRAWN DATE SDH 12/10/12 CHECKED DATE DRAWING TITLE OUTLINE, RECLOSER 1-PH, 15-27KV SCALE SHT. SIZE SHT. No. DRAWING NUMBER DATE APPROVED NEXT ASS'Y 3/16 C 1 of C0110 REV ECN- DESCRIPTION BY CHK. DATE THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C

14 Outline Drawings Single-Phase 15/27kV 3188C DRAWING NUMBER REV ALTERNATE POSITION ENGINEERING SPEC. QUALITY STD. MATERIAL STD. ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION INCH mm ENGLISH METRIC DUAL INCH mm MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH 6.09 [154,6] DRAWN DATE SDH 12/10/12 CHECKED DATE DRAWING TITLE OUTLINE, RECLOSER 1-PH, 15-27KV SCALE SHT. SIZE SHT. No. DRAWING NUMBER DATE RECLOSER REV ECN- DESCRIPTION BY CHK. DATE x APPROVED NEXT ASS'Y 3/16 C 2 of C [349,2] 2.88 [73] 1/4-20 BOLT WASHER/NUT LINE SIDE 1/2-13 BOLT/NUT FOR 1/2-13 BOLT/NUT FOR MOUNTING FRAME 3/8-16 BOLT/WASHER FOR MTG FRAME THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C0110

15 Single-Phase 38kV DRAWING NUMBER REV 3188C RECLOSER CLEARANCE SLOT FOR USER SUPPLIED 5/8[16] DIA LAG OR THRU BOLT ENGINEERING SPEC. QUALITY STD. MATERIAL STD. ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION INCH mm ENGLISH METRIC DUAL INCH mm MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH DRAWING TITLE DRAWN DATE SDH 01/03/12 CHECKED DATE OUTLINE, RECLOSER 1-PH, 38KV DATE APPROVED SHT. SIZE SHT. No. SCALE DRAWING NUMBER 3/16 C 1 of C0111 NEXT ASS'Y [255,6] 6) CREEPAGE DISTANCE: LINE TO GROUND = 51.00" [1295] LOAD TO LINE = 60.00" [1524] 7) INTERRUPTER RATING = 12.5 KA 8) BIL: LINE TO GND = 170KV LINE TO LINE = 170KV NOTES: 1) DIMENSIONS IN BRACKETS [XXX] ARE MILLIMETERS. 2) MAXIMUM CANTILEVERED TERMINAL PAD LOAD OF 60 LBS. [27 KG.] PER PAD ALLOWABLE. HORIZONTAL CABLE TENSIONS PER PHASE TO BE OPPOSITE IN DIRECTION. 3) WEIGHT= 58 LBS. [26.3 KG.] 4) STANDARD POSITION AS SHOWN. TRIP POSITION SHOWN DOTTED. 5) CONNECTION OF THE RECLOSER TO THE DESIGNATED LINE AND TERMINALS IS ONLY REQUIRED IF THE RECLOSER IS BEING USED WITH A CONTROL CONTAINING DIRECTIONAL OVER CURRENT CAPABILITY [70,3] [328,5] CABLE CONNECTION PROVISION [791,9] OPEN - GREEN BLACK CLOSED - RED BLACK OPEN/CLOSE INDICATOR LINE SIDE (SEE NOTE 5) 1.75 [44,5] (SEE NOTE 5) [609,3] x [890,2] 8.64 [219,4] [498] 3/8-16 BOLT FOR SECURING RECLOSER TO FRAME MANUAL TRIP HANDLE SEE NOTE 4 OPEN/CLOSE INDICATOR (SEE VIEW) REV ECN- DESCRIPTION BY CHK. DATE THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C

16 Outline Drawings Single-Phase 38kV DRAWING NUMBER REV 3188C ENGINEERING SPEC. QUALITY STD. MATERIAL STD. ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION INCH mm ENGLISH METRIC DUAL INCH mm MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH DRAWING TITLE DRAWN DATE SDH 01/03/12 CHECKED DATE OUTLINE, RECLOSER 1-PH, 38KV DATE ALTERNATE POSITION 6.09 [154,6] RECLOSER 03/29/12 REV ECN- DESCRIPTION BY CHK. DATE x APPROVED SHT. SIZE SHT. No. SCALE DRAWING NUMBER 3/16 C 2 of C0111 NEXT ASS'Y [349,2] 2.88 [73] 1/4-20 BOLT WASHER/NUT LINE SIDE 1/2-13 BOLT/NUT FOR 1/2-13 BOLT/NUT FOR MOUNTING FRAME 3/8-16 BOLT/WASHER FOR MTG FRAME THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C0111

17 Three-Phase 15/27kV DRAWING NUMBER REV 3188C CLOSED - RED BLACK OPEN/CLOSE INDICATOR SCALE 1/4 PENDING ECN A PLEASE CONTACT ENGINEERING FOR CURRENT REVISION CLEARANCE SLOTS FOR USER SUPPLIED 3/4 [19] DIA LAG OR THRU BOLTS LINE SIDE (SEE NOTE 5) 1.75 [44,5] 1.50 [38,1] [892,2] [381,3] NAMEPLATE ENGINEERING SPEC. QUALITY STD. MATERIAL STD. DIMENSIONS ON THIS DWG BELOW ALL ARE IN UNITS AS CHECKED THIRD ANGLE PROJECTION INCH mm ENGLISH METRIC DUAL INCH mm MVR3 RECLOSER MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH DRAWING TITLE DRAWN DATE sdh 11/28/11 CHECKED DATE OUTLINE, RECLOSER 3-PH, 15-27KV DATE APPROVED 2 UPDATED FRONT, SH2 SDH 11/30/12 SHT. SIZE SHT. No. SCALE DRAWING NUMBER 1/8 C 1 of C0112 NEXT ASS'Y 1 G16309 UPDATE SHT 2 ADD SHT 3 SDH 9/21/12 REV ECN- DESCRIPTION BY CHK. DATE [328,9] LIFT SWITCH HERE CABLE CONNECTION PROVISION [857,6] OPEN - GREEN [417,6] [1081] BLACK TORQUE TERMINAL LUGS TO 25 FT/LBS [393,7] [393,7] 1.75 [44,5] (SEE NOTE 5) [616,1] [496,8] MANUAL TRIP HANDLE SEE NOTE 4 OPEN/CLOSE INDICATOR (SEE VIEW) 6) CREEPAGE DISTANCE: LINE TO GROUND = 41.50" [1054] LOAD TO GROUND = 43.60" [1107] LINE TO LOAD = 52.17" [1320] 7) INTERRUPTER RATING = 12.5 KA 8) BIL: LINE TO GND = 150KV LINE TO LINE = 150KV NOTES: 1) DIMENSIONS IN BRACKETS [XXX] ARE MILLIMETERS. 2) MAXIMUM CANTILEVERED TERMINAL PAD LOAD OF 60 LBS. [27 KG.] PER PAD ALLOWABLE. HORIZONTAL CABLE TENSIONS PER PHASE TO BE OPPOSITE IN DIRECTION. 3) WEIGHT= 208 LBS. [94.4 KG.] 4) STANDARD POSITION AS SHOWN. TRIP POSITION SHOWN DOTTED. 5) CONNECTION OF THE RECLOSER TO THE DESIGNATED LINE AND TERMINALS IS ONLY REQUIRED IF THE RECLOSER IS BEING USED WITH A CONTROL CONTAINING DIRECTIONAL OVER CURRENT CAPABILITY. THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C

18 Outline Drawings Three-Phase 15/27kV DRAWING NUMBER REV 3188C PENDING ECN A PLEASE CONTACT ENGINEERING FOR CURRENT REVISION ENGINEERING SPEC. QUALITY STD. MATERIAL STD. ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION INCH mm ENGLISH METRIC DUAL INCH mm MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH DRAWN DATE SDH 12/27/11 OUTLINE, RECLOSER 3-PH, 15-27KV DRAWING TITLE DATE CHECKED DATE APPROVED SHT. SIZE SHT. No. SCALE DRAWING NUMBER 1/8 D 2 of C0112 NEXT ASS'Y 18 ALTERNATE TRANSFORMER POSITION [984] 9.75 [247,7] LINE SIDE [492] LINE SIDE S x 1/2-13 BOLT/NUT FOR LINE SIDE ARRESTORS ALTERNATE TRANSFORMER POSITION TRANSFORMER [480,9] ALTERNATE POSITION 8.93 [226,9] [624,71] MOUNTING FRAME FOR LINE S AND TRANSFORMERS 5/8-11 BOLT/NUT FOR MTG FRAME RECLOSER 3/8-16 BOLT/WASHER FOR FRAME S 5/8-11 BOLT/NUT FOR TRANSFORMER 1/2-13 BOLT/NUT FOR S FRAME MVR3 RECLOSER WITH LINE SIDE AND FRAMES 2 UPDATED FRONT, SH2 SDH 11/30/12 1 G16309 UPDATE SHT 2 ADD SHT 3 SDH 9/21/12 REV ECN- DESCRIPTION BY CHK. DATE THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C0112

19 Three-Phase 38kV 3188C DRAWING NUMBER REV CLOSED - RED BLACK OPEN/CLOSE INDICATOR SCALE 1/4 PENDING ECN D PLEASE CONTACT ENGINEERING FOR CURRENT REVISION CLEARANCE SLOTS FOR USER SUPPLIED 3/4 [19] DIA LAG OR THRU BOLTS LINE SIDE (SEE NOTE 5) 1.75 [44,5] 1.50 [38,1] [892,2] [381,3] NAMEPLATE ENGINEERING SPEC. QUALITY STD. MATERIAL STD. DIMENSIONS ON THIS DWG BELOW ALL ARE IN UNITS AS CHECKED THIRD ANGLE PROJECTION INCH mm ENGLISH METRIC DUAL INCH mm MVR3 RECLOSER MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH DRAWING TITLE DRAWN DATE sdh 11/28/11 CHECKED DATE OUTLINE, RECLOSER 3-PH, 38KV DATE APPROVED 2 UPDATE FRAME. SH2 SDH 11/30/12 SHT. SIZE SHT. No. SCALE DRAWING NUMBER 1/8 C 1 of C0113 NEXT ASS'Y 1 G16348 UPDATE SHT 2 ADD SHT 3 SDH 9/21/12 REV ECN- DESCRIPTION BY CHK. DATE [328,9] LIFT SWITCH HERE CABLE CONNECTION PROVISION [903,5] BLACK OPEN - GREEN [463,6] [1081] [393,7] TORQUE TERMINAL LUGS TO 25 FT/LBS [393,7] 1.75 [44,5] (SEE NOTE 5) [616,1] [496,8] MANUAL TRIP HANDLE SEE NOTE 4 OPEN/CLOSE INDICATOR (SEE VIEW) 6) CREEPAGE DISTANCE: LINE TO GROUND = 51.00" [1295] LOAD TO GROUND = 52.00" [1320] LINE TO LOAD = 60.56" [1538] 7) INTERRUPTER RATING = 12.5 KA 8) BIL: LINE TO GND = 170KV LINE TO LINE = 170KV NOTES: 1) DIMENSIONS IN BRACKETS [XXX] ARE MILLIMETERS. 2) MAXIMUM CANTILEVERED TERMINAL PAD LOAD OF 60 LBS. [27 KG.] PER PAD ALLOWABLE. HORIZONTAL CABLE TENSIONS PER PHASE TO BE OPPOSITE IN DIRECTION. 3) WEIGHT= 211 LBS. [95.7 KG.] 4) STANDARD POSITION AS SHOWN. TRIP POSITION SHOWN DOTTED. 5) CONNECTION OF THE RECLOSER TO THE DESIGNATED LINE AND TERMINALS IS ONLY REQUIRED IF THE RECLOSER IS BEING USED WITH A CONTROL CONTAINING DIRECTIONAL OVER CURRENT CAPABILITY. THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C

20 Outline Drawings Three-Phase 38kV DRAWING NUMBER REV 3188C PENDING ECN A PLEASE CONTACT ENGINEERING FOR CURRENT REVISION ENGINEERING SPEC. QUALITY STD. MATERIAL STD. ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION INCH mm ENGLISH METRIC DUAL INCH mm MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH DRAWN DATE SDH 12/27/11 CHECKED DATE OUTLINE, RECLOSER 3-PH, 38KV DRAWING TITLE DATE APPROVED SHT. SIZE SHT. No. SCALE DRAWING NUMBER 1/8 D 2 of C0113 NEXT ASS'Y 20 ALTERNATE TRANSFORMER POSITION LINE SIDE S LINE SIDE [984] 9.75 [247,7] x [492] ALTERNATE TRANSFORMER POSITION 1/2-13 BOLT/NUT FOR LINE SIDE ARRESTORS TRANSFORMER [480,9] 8.93 [226,9] ALTERNATE POSITION [624,71] MOUNTING FRAME FOR LINE S AND TRANSFORMERS 5/8-11 BOLT/NUT FOR MTG FRAME RECLOSER 3/8-16 BOLT/WASHER FOR FRAME S 5/8-11 BOLT/NUT FOR TRANSFORMER 1/2-13 BOLT/NUT FOR S 3/8-16 BOLT/WASHER FOR FRAME FRAME MVR3 RECLOSER WITH LINE SIDE AND FRAMES 2 UPDATE FRAME, SH 2 SDH 11/30/12 1 G16348 UPDATE SHT 2 ADD SHT 3 SDH 9/21/12 REV ECN- DESCRIPTION BY CHK. DATE THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C0113

21 - - - x Schematic Drawings Single-Phase 15/27/38kV DRAWING NUMBER REV 3188C ENGINEERING SPEC. QUALITY STD. MATERIAL STD. - - ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION INCH mm ENGLISH METRIC DUAL INCH mm MATERIAL 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) FINISH DRAWN DATE SDH 01/19/12 DRAWING TITLE CHECKED DATE - - J BLOCK DIAGRAM, SINGLE PHASE RECLOSER, 351RS CONTROL J SOURCE SIDE CLOSE COIL TRIP 69a DATE APPROVED SCALE SHT. SIZE SHT. No. DRAWING NUMBER 3188C0115 NEXT ASS'Y 1 OF 1 G16324 JMG 1 - SDH 9/18/12 REV BY DATE DESCRIPTION CHK PIN CONTROL CABLE C C CT D I ELASTIMOLD MVR SINGLE - PHASE RECLOSER VACUUM CONTACT MANUALLY PULL OPEN TO TRIP NOTES 3.4 MANUAL TRIP LEVER (69) NOTES: 1. LIMIT SWITCHES ARE SHOWN WITH THE MANUAL TRIP LEVER (69) IN THE TRIPPED POSITION. 2. PIN E IS NOT USED WHEN PAIRED WITH A SEL 351RS KESTREL CONTROL. WHEN PAIRED WITH A SEL 651Rx2 CONTROL PIN E IS USED ,000:1 VOLTAGE RATIO. 4. CAPACITIVE VOLTAGE DIVIDER IS INTEGRATED INTO THE MVR. NOTE 1 NOTE 1 NOTE 1 SEL-351R KESTREL SINGLE - PHASE RECLOSER CONTROL D CT RETURN E E NOT USED C1 NOTE 2 NOT USED F F 2 G G GND TRIP K K CLOSE A A 52a MONIT0RED TRIP/CLOSE (52a) B B 69b MONITORED MANUAL TRIP (69b) H H 12Vdc WHETTING VOLTAGE RECLOSER CABLE RECEPTACLE CONTROL CABLE RECEPTACLE THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. Drawing Number: 3188C

22 - - x - - Schematic Drawings Three-Phase 15/27/38kV THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. NOTES: 1. LIMIT SWITCHES ARE SHOWN WITH THE MANUAL TRIP LEVER (69) TRIPPED (RECLOSER IS OPEN) _1, _2, _3 ARE SEPARATE LIMIT SWITCHES ASSOCIATED WITH THE MANUAL TRIP LEVER (69) LIMIT SWITCH ,000:1 VOLTAGE RATIO. 4. CAPACITIVE VOLTAGE SENSORS ARE INTEGRATED INTO THE MVR. 5. RESISTIVE VOLTAGE SENSORS ARE ADD ON MODULES TO THE MVR. SEL 651R RECLOSER CONTROL SOURCE SIDE PHASE 1 VOLTAGE SENSOR SOURCE SIDE PHASE 2 VOLTAGE SENSOR SOURCE SIDE PHASE 3 VOLTAGE SENSOR SOURCE SIDE GND PHASE 1 CT PHASE 2 CT PHASE 3 CT CT RETURN PHASE 1 VOLTAGE SENSOR PHASE 2 VOLTAGE SENSOR PHASE 3 VOLTAGE SENSOR GND GND CLOSE (COIL 1) N P R S A B C D J K L M G Y 32-PIN CONTROL CABLE I 1 I 2 I 3 I IN N P R S A B C D J K L M G Y 69_1 R5 R4 C1 12 Y1 COIL 1 ELASTIMOLD MVR THREE-PHASE RECLOSER I SOURCE SIDE R7 C2 TRIP 1 R6 22 Y2 R9 C3 R I 2 I 3 NOTE 2 Y3 MANUALLY PULL OPEN TO TRIP VACUUM CONTACTS MANUAL TRIP LEVER (69) NOTES 3,4 NOTES 3,5 1 G SDH - 9/18/12 REV DESCRIPTION BY CHK. DATE TRIP (COIL 1) CLOSE (COIL 2) TRIP (COIL 2) CLOSE (COIL 3) TRIP (COIL 3) 12Vdc WHETTING VOLTAGE Z f g h j F Z f g h j F 69_2 69_3 COIL 2 COIL 3 TRIP 2 TRIP 3 CLOSE 1 NOTE 2 CLOSE 2 NOTE 2 CLOSE 3 22 NEXT ASS'Y SCALE SHT. SIZE SHT. No. DRAWING NUMBER 1 OF C0114 APPROVED DATE - - BLOCK DIAGRAM, 651R CONTROL, MVR CHECKED DATE - - DRAWING TITLE DRAWN DATE SDH 01/19/12 FINISH 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) MATERIAL ENGLISH INCH METRIC mm DUAL INCH mm ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION ENGINEERING SPEC. QUALITY STD. MATERIAL STD. - - MONITORED TRIP/CLOSE (52a1) MONITORED TRIP/CLOSE (52a2) MONITORED TRIP/CLOSE (52a3) MONITORED MANUAL TRIP (69) U V W X CONTROL CABLE RECEPTACLE U V W X RECLOSER CABLE RECEPTACLE 52a1 52a2 52a3 69 NOTE 1 DRAWING NUMBER REV 3188C Drawing Number: 3188C0114

23 x Power Module (for use with SEL 351R) THOMAS & BETTS, PROPRIETARY RIGHTS THIS INFORMATION IS TRANSMITTED SUBJECT TO THE FOLLOWING UNDERSTANDING AND AGREEMENT BY ACCEPTANCE OF THIS DOCUMENT YOU AGREE THAT ALL RIGHTS TO THE DRAWINGS AND INFORMATION CONTAINE HEREON, AS WELL AS TO THE SUBJECT MATTER HEREOF AND ALL PROPRIETARY AND NOVEL FEATURES DISCLOSED HEREIN, ARE RESERVED BY THOMAS AND BETTS AND THAT DEVICES EMBODYING SUCH FEATURES ORINFORMATION DERIVED FROM THESE DRAWINGS WILL NOT BE MANUFACTURED BY OR FOR YOU OR DISCLOSED TO OTHERS WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF THOMAS AND BETTS. THESE DRAWINGS AND THE INFORMATION CONTAINED THEREIN ARE AND REMAIN THE PROPERTY OF THOMAS AND BETTS AND ARE NOT TO BE COPIED OR REPRODUCED OR DISCLOSED TO OTHERS WITHOUT THE PRIOR WRITTEN CONSENT OF THOMAS AND BETTS ALL DRAWINGS AND INFORMATION TO BE RETURNED TO THOMAS AND BETTS UPON DEMAND OR UPON COMPLETION OF PURPOSE FOR WHICH LENT. NOTES: 1. LIMIT SWITCHES ARE SHOWN WITH THE MANUAL TRIP LEVER (69) TRIPPED (RECLOSER IS OPEN) _1, _2, _3 ARE SEPARATE LIMIT SWITCHES ASSOCIATED WITH THE MANUAL TRIP LEVER (69) LIMIT SWITCH. 3. PINS N AND P ARE NOT USED NORMALLY, CAN BE USED FOR CAP READY STATUS ,000:1 VOLTAGE RATIO. 5. CAPACITIVE VOLTAGE SENSORS ARE INTEGRATED INTO THE MVR AND ARE PRE-CALIBRATED. 6. RESISTIVE VOLTAGE SENSORS ARE ADD ON MODULES TO THE MVR AND ARE PRE-CALIBRATED. 7. THE RESISTIVE AND CAPACITIVE VOLTAGE SENSORS ARE NOT USED WHEN USING A 351R CONTROL. NOTE 3 SEL 351R RECLOSER CONTROL 24Vdc MONITORED TRIP CIRCUIT POINT TRIP MONITORED TRIP CIRCUIT POINT CLOSE MONITORED CLOSE CIRCUIT POINT PHASE 1 CT PHASE 2 CT PHASE 3 CT CT RETURN NOT USED GND NOT USED A B C D E F G H J K L M N 14-PIN CONTROL CABLE A B C D E F G H J K L M N 24Vdc MONITOR TRIP TRIP COMMAND MONITOR TRIP CLOSE COMMAND MONITOR CLOSE NOT USED CAP READY ELASTIMOLD POWER MODULE NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED GND N P R S A B C D J K L M G 32-PIN CONTROL CABLE I 1 I 2 I 3 I IN N P R S A B C D J K L M G R5 R4 C1 ELASTIMOLD MVR THREE-PHASE RECLOSER SOURCE SIDE R7 C2 R6 I 1 I 2 R9 C3 R8 32 I 3 NOTES 4,6,7 MANUALLY PULL OPEN TO TRIP NOTES 4,5,7 VACUUM CONTACTS MANUAL TRIP LEVER (69) NEXT ASS'Y REV DESCRIPTION BY CHK. DATE 1 OF C G SDH JMG 9/18/12 SCALE SHT. SIZE SHT. No. DRAWING NUMBER 2 G16418 PIN M FOR GROUND, PICTORIAL JMG - 11/27/12 CHECKED DATE - - APPROVED DATE - - BLOCK DIAGRAM, 351R POWER MODULE DRAWING TITLE DRAWN DATE SDH 02/06/12 FINISH 8155 T&B Boulevard Memphis, TN Phone: (800) Fax: (800) MATERIAL ENGLISH INCH METRIC mm DUAL INCH mm ALL DIMENSIONS ON THIS DWG ARE IN UNITS AS CHECKED BELOW THIRD ANGLE PROJECTION ENGINEERING SPEC. QUALITY STD. MATERIAL STD. - - NOT USED P CONTROL CABLE RECEPTACLE P POWER MODULE RECEPTACLE CAP READY COIL 1 (CLOSE) COIL 1 (OPEN) COIL 2 (CLOSE) COIL 2 (OPEN) COIL 3 (CLOSE) COIL 3 (OPEN) DIGITAL GND PHASE 1 LIMIT SWITCH PHASE 2 LIMIT SWITCH PHASE 3 LIMIT SWITCH LOCKOUT Y Z f g h j F U V W X POWER MODULE RECEPTACLE Y Z f g h j F U V W X RECLOSER CABLE RECEPTACLE 69_1 69_2 69_3 52a1 52a2 52a3 69 Y1 COIL 1 COIL 2 COIL 3 TRIP 1 TRIP 2 TRIP 3 NOTE 1 Y2 NOTE 2 CLOSE 1 NOTE 2 CLOSE 2 NOTE 2 CLOSE 3 Y3 DRAWING NUMBER REV 3188C Drawing Number: 3188C

24 Section 3: Design Test Data Elastimold MVR Test Data Summary Elastimold MVRs are tested under the requirements of ANSI C are certified as single-phase devices and are capable of single-phase tripping on all grounded and ungrounded circuits within their respective rated maximum voltages (17.1kV for 15kV units and 29.3kV for 27kV units). are certified for use as a single-phase device capable of single-phase tripping on grounded circuits and as a three-phase device capable of three-phase tripping only on ungrounded circuits. The table below highlights the testing covered in Elastimold Test Report # Test Report C Standard Clause & Description 15kV MVR Compliance 27kV MVR Compliance 38kV MVR Compliance 6.2 Insulation (Dielectric) Tests 6.3 Switching Tests 6.4 Making Current Capability 6.5 Operating Duty Tests 6.6 Minimum Tripping Current Tests 6.7 Partial Discharge (Corona) Tests 6.10 Temperature Rise Tests 6.11 Time-Current Tests 6.12 Mechanical Duty Tests 6.13 Surge Withstand Capability (SWC) Tests Other Testing UV/Weathering Tests Other Testing IEC Salt Fog Spray Test (1,600 hrs.) Please ask your Thomas & Betts sales representative for a complete catalog of quality Thomas & Betts electrical products or visit us at. For customer service, call For technical questions, call Thomas & Betts Corporation. All rights reserved. Printed in the U.S.A. 01/13/1M Rev. 1 IS-1335 Thomas & Betts Corporation Electrical Division 8155 T&B Boulevard Memphis, TN