How-To Assemble Your GATHERING GRILL

Size: px

Start display at page:

Download "How-To Assemble Your GATHERING GRILL"

Rudolph Owens
6 years ago
Views:

Gathering Grill (FPS-200) ssembly Instructions How-To ssemble Your GTHERING GRILL PRT NO.

GENERL SHLE OUTDOOR LIVING PRODUCT WRRNTY ll General Shale Outdoor Living products are warranted to be made from

Outdoor Living products are intended for recreational or residential use and are not warranted for any other

1 Gathering Grill (FPS-200) ssembly Instructions How-To ssemble Your GTHERING GRILL PRT NO. FPS-200 DIFFICULTY BEGINNER PPROX. DIM. 3'3"W x 2'8"D x 1'7"H PPROX. WEIGHT 1,600 lbs. GENERL SHLE OUTDOOR LIVING PRODUCT WRRNTY ll General Shale Outdoor Living products are warranted to be made from high quality materials that meet or exceed STM material standards. Outdoor Living products are intended for recreational or residential use and are not warranted for any other purpose. The life of the product depends on correctness of installation and extent of usage. ll metal components are subject to normal rust and corrosion. NY IMPLIED WRRNTIES RE HEREBY DISCLIMED ND RE EXPRESSLY EXCLUDED.

Gathering Grill (FPS-200) ssembly Instructions Materials included with your outdoor kit.

Block C2 (4" x 8" x 8") Weathered Bullnose Block C3 (4" x 3 5/8" x 8") (1) Grate Insert (not pictured below) (1) sh Pan (not

C2 4" x 8" x 8" 4" x 8" x 8" 4" x 8" x 16" C3 4" x 3 5/8" x 8" dditional materials required to install your kit.

place of supplied thin set mix. NOTE: This unit is designed for outdoor use only.

2 Gathering Grill (FPS-200) ssembly Instructions Materials included with your outdoor kit. (37) (10) (4) (4) Weathered Block (4" x 8" x 16") Weathered Single Bullnose Block (4" x 8" x 8") Weathered Bullnose Corner Block C2 (4" x 8" x 8") Weathered Bullnose Block C3 (4" x 3 5/8" x 8") (1) Grate Insert (not pictured below) (1) sh Pan (not pictured below) (1) Thin Set Mix Bag (not pictured below) Reference images. Images are not to scale. C2 4" x 8" x 8" 4" x 8" x 8" 4" x 8" x 16" C3 4" x 3 5/8" x 8" dditional materials required to install your kit. Concrete or Gravel (for setting base) Level Mixing Bucket Note: You may also use landscape adhesive (available separately) in place of supplied thin set mix. NOTE: This unit is designed for outdoor use only. This unit is not designed to be used on wood decks or under roof enclosures. Locate unit reasonable distance from any combustible materials. Comply with local building code(s) and burning permits as applicable. Retain these instructions with unit. 2

Gathering Grill" (FPS-200) ssembly Instructions 1 Create a level base using Crusher Run Stone to accommodate the overall footprint of the grill.

Excavate/remove soft soil as required to provide level stone surface at a minimum of 4" deep. If required, use landscape blocks to retain stone base.

Reference diagrams for creating a level base. Existing Ground Screed Stone Base Level 4"min.

3 Gathering Grill" (FPS-200) ssembly Instructions 1 Create a level base using Crusher Run Stone to accommodate the overall footprint of the grill. Prepare an area 3'9" wide x 3'2" deep. Remove sod and vegetation. Excavate/remove soft soil as required to provide level stone surface at a minimum of 4" deep. If required, use landscape blocks to retain stone base. If installing optional hearth/knee wall, extend base as required. If soil under sod is hard, soil can be leveled out and used as a base material. Reference diagrams for creating a level base. Existing Ground Screed Stone Base Level 4"min. Crusher Run Stone 4" Undisturbed Ground (Base Section View) 3'9" 3'3" x 2'8" Grill Outline 3'2" 3'9" x 3'2" Crusher Run Base (4" min. thickness) GRILL FRONT (Base Plan View) NOTE: ll outdoor living kits can be installed directly on a properly prepared stone base. However, for best performance and appearance, a concrete pad is recommended. 3

4 Gathering Grill" (FPS-200) ssembly Instructions 2 Begin building the grill (courses 1 though 4). Use supplied thin set between each course; apply to the middle of the block to avoid squeezing it out from between courses. fter laying the first course, check to make sure it is level before proceeding. Course 1 and 3 Course 2 (10) Weathered Block (4" x 8" x 16") (10) Weathered Block (4" x 8" x 16") Course 4 (7) Weathered Block (4" x 8" x 16") 4

pply a small amount of thin set in the vertical joints of course 5.

5 Gathering Grill" (FPS-200) ssembly Instructions 3 Continue building the grill (course 5). Use supplied thin set between each course. pply a small amount of thin set in the vertical joints of course 5. C2 C3 C2 C3 C3 C2 C3 C2 Course 5 (10) Weathered Single Bullnose Block (4" x 8" x 8") (4) Weathered Bullnose Corner Block C2 (4" x 8" x 8") (4) Weathered Bullnose Block C3 (4" x 3 5/8" x 8") 5

Season the cooking grate by applying several thin coats of oil. This will protect the metal from getting rusted and makes for a non-stick cooking surface.

6 Gathering Grill" (FPS-200) ssembly Instructions 4 Install metal grate. Simply slide metal grate into the opening of course 5. 5 Install ash pan. Simply slide/place the metal ash pan into the opening of course 4. NOTE: Before using your Gathering Grill, wash the metal cooking grate with warm water and dish detergent. Season the cooking grate by applying several thin coats of oil. This will protect the metal from getting rusted and makes for a non-stick cooking surface. Season the surface by applying a thin coat of neutral good grade oil (vegetable oil, canola oil, sunflower oil, shortening or lard). Repeat this process after the first time and after the grate has allowed to cool. OL-BRO

How-To Assemble Your SERENITY 200

How-To Assemble Your SERENITY 200 Serenity 200 Fireplace (FPL-200) ssembly Instructions How-To ssemble Your SERENITY 200 Outdoor Fireplace PRT NO. FPL-200 IFFICULTY VNCE PPROX. IM. 5'W x 4' x 8'9"H PPROX. WEIGHT 7,540 lbs. GENERL SHLE