Lad with min. 5 kg 405000090 405070090 INSTALLATION INSTRUCTIONS CONTENT: 1. Imprtant safety instructins. 2. Specificatins and main dimensins. 3. Parts included. 4. Installatin. 5. Adjusting the strke length f the lift. 6. Declaratin f cnfrmity. WARNING WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PROD- UCT MAY RESULT IN SERIOUS BODILY INJURY. 1 N. #324360.3
1. Imprtant safety Instructins. CAUTION: Befre yu begin any f the Installatin prcedures (4. Installatin.), read and fllw the warnings and safety instructins n this page. WARNING! THIS IS NOT A TOY! WARNING! CHILDREN SHOULD NOT OPERATE LIFT OR REMOTE CONTROL! Use the fllwing safety guidelines t help prtect yur lift frm ptential damage and t ensure yur wn persnal safety. Read all the installatin instructins befre testing r installing yur lift. Read and fllw all safety instructins. Keep remte cntrl and manual rcker switch ut f reach f children. T prevent bdily injury keep hands and clthing away frm the lift while the lift is in peratin. Befre installing the lift r wrking with its cnnectins, unplug the lift frm the electricity main supply. D nt install the lift, pwer supply r R.F. mdule in places subject t high temperatures fr example near a radiatr, r heating vent. The TV lift must nly be munted in a dry area and it must be ensured befre use that the lift is safe r prtected frm liquid cntact r spillage. T avid damaging the pwer supply, R.F. mdule and pwer crd, d nt put anything n it r place it where it culd becme damaged. Unplug the lift in the fllwing cnditins: When the pwer crd r plug is damaged r frayed. If the lift, pwer supply r RF mdule has been expsed t rain r water r any liquid cntaminatin whatever. If the lift exhibits a distinct change in perfrmance, indicating a need fr attentin. MANUFACTURES wh build this lift int ther prducts r use it with ther prducts, MUST make sure t prevent bdily injury. The MANUFACTURER f the final prduct is respnsible t give the end user prper warnings and instructins fr use. 2
2. Specificatins and main dimensins. Materials and weights: Steel, black pwder cated - Weight ~ 17/23 kg Max. wrking lads: 65 kg (by standard installatin) 29 kg (when lift is munted upside dwn) 100 kg peak lad Duty cycle: 10% by 50% f wrking lad r max 2 min. cntinuusly Operatin: Remte and rcker switch Vltage: 100-240 VAC / 50/60Hz Standby Cnsumptin: < 1 Watt Abve specificatins may vary depending n lcal temperature, humidity and input vltage. Main dimensins, 405070090 [mm]: VESA, 405070090 : 400x400, 400x200, 400x100 300x300 (see venset.cm fr munting instructin) 200x200, 200x100 100x100 3
Main dimensins, 405000090 [mm]: VESA, 405000090 : 600x400, 600x200, 600x100 400x400, 400x200, 400x100 300x300, 200x200, 200x100 4
3. Parts included. Lift unit ( #1 ) Lid lifter ( #2 ) Lift brackets ( #3 ) TV munting brackets ( #4 ) (405000090 nly) R.F. Mdule ( #5 ) Remte cntrl ( #6 ) AC input wire, cuntry cnfigured ( #7 ) Pwer supply bracket ( #8 ) Rcker switch ( #9 ) Pwer supply ( #10 ) Lid lifter ( #2 ) Lift brackets ( #3 ) (smaller fr 405070090 ) Lift unit ( #1 ) TV munting brackets ( #4 ) (405000090 nly) R.F. Mdule ( #5 ) Remte cntrl ( #6 ) Pwer supply ( #10 ) AC input wire, cuntry cnfigured ( #7 ) Pwer supply munting bracket ( #8 ) Rcker switch ( #9 ) 5
4. Installatin. 1) Remve all cntents frm packaging and cmpare with parts list. 2) Place the lift unit (#1) n e.g. the back panel f the cabinet** in a lcatin that will allw full up and dwn mvement f the lift. 3) Fasten the unit securely t the cabinet. Screws must be apprpriate fr the material being used. 4) Cnnect the plugs frm lift unit (#1) and pwer supply (#10) t R.F. Mdule (#5). Please als refer t the separate user instructin fr the remte unit, next page. 5) Munt rcker switch (#9) in an easy lcatin by cutting a ø30 hle and pressing the switch int place. Secure excess wire t keep away frm mving parts. 6) Plug the pwer crd int main electrics and add minimum 5kg and perate manual rcker switch. Helpful hint: Munt TV lift and electrnics t plywd panel and attach t inside back f cabinet using apprpriate number f screws. This allws all cmpnents t be remved frm the cabinet if necessary. If this is nt pssible, create an access panel t the electrnics. ** Aim t create access fr wear and tear replacement strke service. 6
User instructin, RF remte system Installatin cnnect the pwer supply and the mtr unit t the remte receiver. 2 different plug sizes make this cnnectin nly pssible t make in the right way after having cnnected the plugs, the blue light will be lit push the emitter buttns and the mtr unit will mve up and dwn fr stpping the mtin ne f the buttns need t be pushed Learning if the remte receiver des nt respnd when pushing the emitter buttns, reset the receiver. After that, cde the emitter and receiver tgether again Cding push the learner buttn n the receiver fr less than 1 sec. push ne f the emitter buttns the red light will start flashing push ne f the emitter buttns again and the red light will turn ff the units nw are cded tgether with a unique cde Reset push and hld dwn the learner buttn n the receiver fr 10 sec. (will be reset when the red light turns ff). External rcker switch the external rcker switch can be cnnected t the receiver, if a fixed peratin unit is required. Truble shting check the plug cnnectins check whether the blue light is n reset the receiver and make a new cding always test the lift n the manual rcker switch 7
Electric TV Lift, 405070090 & 405000090 Setting ptins fr peratin f lift This remte system has 4 jumpers inside the remte receiver bx, these can be lifted and psitined Left r Right depending f hw the functinality f the lift shuld be. Jumper A Pwer safety cut ff time Default Left = 60 secnds. If mved t right psitin then the lift will pwer ff autmatically after the mtr has run fr 20 secnds. Jumper B Remte emitter functin Default Right = the buttns n the emitter nly need t be pushed nce fr activatin. If mved t the left psitin then the emitter buttn will need t be held dwn during the peratin f the lift, ie..fr use where a higher level f safety may be required. Jumper C Aut-reverse time (type A lifts nly) Default Right = a reverse perid f 1 secnd. If mved t the left psitin, the reverse time is reduced t 0.6 f a secnd. Jumper D Using the lift upside dwn (type A lifts nly) Default Right = nrmal peratin in an upright psitin ie.. t raise a TV up and dwn frm a flr standing cabinet. If mved t the left psitin the reverse functin will wrk with the lift munted up-side dwn ie.. t lwer dwn and up a TV frm the bttm f a wall munted cabinet. If n reverse functin is required then remve the jumper. Change f battery in emitter (battery type 27A/12V) remve lid n back side lift up battery place new battery Please be aware that string emitter in envirnment with high humidity may damage the prduct. FCC Statement This device cmplies with Part 15 f the FCC rules. Operatin is subject t the fllwing tw cnditins; 1) This device may nt cause any harmful interference and 2) This device must accept any interference received, including interference that may cause undesired peratin. 8
5. Adjusting the strke length f the lift. Adjusting the bttm stp: The bttm stp can be adjusted t any preferred height, e.g. if yu dn t want the lift t g all the way dwn int the cabinet. Yu can adjust just ne r bth end stps. Fig. 1 1. The mre yu mve the glider dwn the cable the earlier the lift will stp n the dwn strke as the end stp switch will be triggered sner. 2. Raise the lift up t the just abve lwest psitin that yu want it t reach n the dwn stke. 3. Remve the small plastic cver plate (see fig.1) and yu will see the glider n the cable. 4. Use a 2.5mm Allen key t lsen the screw inside the glider. (see fig.1) 5. Mve the glider dwn the cable accrdingly and tighten the screw securely. 6. Replace the plastic cver plate, the glider will n lnger be in this windw. 7. Test the lift fully up and dwn and check the desired bttm stp psitin is as yu require. 9
Adjusting the tp stp: The tp stp can be adjusted t any preferred height, e.g. if yu dn t want the lift t g all the way up ut f the cabinet. Yu can adjust just ne r bth end stps. Fig. 2 1. The mre yu mve the glider dwn the cable the earlier the lift will stp n the up strke as the end stp switch will be triggered sner. 2. Raise the lift up t full height. 3. Yu will see the glider n the cable belw the nyln brushes (see fig.2) 4. Use a 2.5mm Allen key t lsen the screw inside the glider. (see fig.2) 5. Mve the glider dwn the cable accrdingly and tighten the screw securely. 6. Test the lift fully up and dwn and check the desired tp stp psitin is as yu require. 10