FS1259 Low-Voltage, 1 Ω Dual SPST nalog Switch with Power-Off Isolation Features Power-Off Isolation (V CC =0 V) 1 Ω On Resistance (R ON ) for 4.5V V CC 0.25 Ω Maximum R ON Flatness for 4.5 V V CC Space-Saving, US8 Surface Mount Package Broad V CC Operating Range: 1.65 V to 5.50 V Fast Turn-On and Turn-Off Times Break-Before-Make Enable Circuitry pplications Cellular Phone Portable Media Player PD Ordering Information Part Number Top Mark Operating Temperature Range FS1259K8X 59-40 C to +85 C Description pril 2014 The FS1259 is a high-performance, dual, Single-Pole / Single-Throw (SPST) analog switch. The device features ultra-low R ON of 1 at 4.5 V V CC and operates over the wide V CC range of 1.65 V to 5.50 V. The FS1259 allows for reduced input thresholds on the select pins. The device is fabricated with sub-micron CMOS technology to achieve fast switching speeds and is designed for break-before-make operation. Package 8-Lead US8, JEDEC MO-187, Variation C, 3.0 mm Wide Packing Method 3000 Units Tape and Reel FS1259 Low-Voltage, 1 Dual SPST nalog Switch with Power-Off Isolation 1 1B 1 8 2 7 V CC 1S 2S 3 6 2B 4 5 2 Figure 1. nalog Symbols FS1259 Rev. 1.0.8
Pin ssignments Pin Definitions 1 1B 2S 1 8 2 7 3 6 4 5 Vcc 1S 2B 2 Figure 2. Pin ssignments (Top View) Pin # Name Description 1 1 Data Port 2 1B Data Port 3 2S Control Input 4 Ground 5 2 Data Port 6 2B Data Port 7 1S Control Input 8 V CC Supply Voltage Truth Table Control Input (S) Function LOW Disconnected HIGH Connected to B FS1259 Rev. 1.0.8 2
bsolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit V CC Supply Voltage -0.5 7.0 V V SW Switch Voltage (1) -0.5 V CC +-0.5 V V IN Input Voltage (1) -0.5 6.5 V I IK Input Diode Current -50 m I SW Switch Current (Continuous) 200 m I SWPEK Peak Switch Current (Pulsed at 1 ms Duration, <10% Duty Cycle) 400 m P D Power Dissipation at 85 C 3.0 µw T STG Storage Temperature Range -65 +150 C T J Maximum Junction Temperature +150 C T L Lead Temperature (Soldering, 10 seconds) +260 C ESD Human Body Model (JEDEC: JESD22-114) 8000 V Charged Device Model (JEDEC: JESD22-C101) 2000 V Machine Model (JEDEC: JESD22-115) 350 V Note: 1. The input and output negative ratings may be exceeded if the input and output diode current ratings are observed. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to bsolute Maximum Ratings. Symbol Parameter Min. Max. Unit V CC Supply Voltage 1.65 5.50 V SEL Control Input Voltage (2) 0 V CC V V SW Switch Input Voltage 0 V CC V T Operating Temperature -40 +85 C J Thermal Resistance, Still ir 215 C/W Note: 2. Control Input must be held HIGH or LOW; it must not float. FS1259 Rev. 1.0.8 3
Electrical Characteristics ll typical values are at 25 C unless otherwise specified. Symbol Parameter V CC (V) Conditions V IH V IL I IN I NO(0FF) I NO(On) Input Voltage High Input Voltage Low Control Input Leakage Off-Leakage Current On-Leakage Current of Port B T =+25 C T =-40 to +85 C Unit Min. Typ. Max. Min. Max. 4.50 to 5.50 1.0 3.00 to 3.60 1.0 2.30 to 2.70 0.95 1.65 to 1.95 0.95 4.50 to 5.50 0.75 3.00 to 3.60 0.65 2.30 to 2.70 0.55 1.65 to 1.95 0.5 5.50 V IN =0 or V CC -10 10-50 50 3.60 V IN =0 or V CC -2 2-20 20 2.70 V IN =0 or V CC -2 2-20 20 1.95 V IN =0 or V CC -2 2-20 20 5.50 3.60 2.70 1.95 =1 V, B=4.5V or B=4.5 V, = 1V =1 V, B=3.0 V or B=3.0 V, =1 V =0.5 V, B=2.3 V or B=2.3, =0.5 V =0.3 V, B=1.65 V or B=1.65, =0.3 V -10 10-50 50-5 5-50 50-5 5-50 50-5 5-50 50 5.50 =Floating; B=4.5 V, 1 V -5 5-50 50 3.60 =Floating; B=3.0 V, 1 V -2 2-20 20 2.70 =Floating; B=2.3 V, 0.5 V -2 2-20 20 1.95 =Floating; B=1.65 V, 0.3 V -2 2-20 20 5.50 =1 V, 4.5 V; B=Floating -5 5-50 50 V V n n n I (ON) On-Leakage Current of Port 3.60 =1 V, 3.0 V; B=Floating -2 2-20 20 2.70 =0.5 V, 2.3; B=Floating -2 2-20 20 n 1.95 =0.3 V, 1.65 V; B=Floating -2 2-20 20 I OFF Power Off Leakage Current of Port & Port B 0 =0 to 5.5 V; B=0 to 5.5 V -1 1-10 10 µ FS1259 Rev. 1.0.8 4
Electrical Characteristics (Continued) ll typical values are at 25 C unless otherwise specified. Symbol Parameter V CC (V) Conditions R PEK R ON R ON R FLT(ON) Peak On Resistance Switch On Resistance (3) On Resistance Matching Between Channels (4) On Resistance Flatness (5) 4.50 3.00 2.30 1.65 4.50 3.00 2.30 1.65 4.50 3.00 2.30 1.65 4.50 3.00 2.30 1.65 1B or 2B=0 to V CC 1B or 2B=0 to V CC I OUT =-8 m, 1B or 2B=0 to V CC I OUT =-2 m, 1B or 2B=0 to V CC 1B or 2B=2.5 V 1B or 2B=2.0 V I OUT =-8 m, 1B or 2B=1.8V I OUT =-2 m, 1B or 2B=1.5 V 1B or 2B=2.5 V 1B or 2B=2.0 V I=-8 m, 1B or 2B=1.8 V I OUT =-2 m 1B or 2B=1.5 V 1B or 2B=1.0 V, 1.5 V, 2.5 V 1B or 2B=0.8 V, 2.0 V I OUT =-8 m, 1B or 2B=0.8 V, 1.8 V I OUT =-2 m, 1B or 2B=0.6 V, 1.5 V T =+25 C T =-40 to +85 C Min. Typ. Max. Min. Max. 0.8 1.0 1.2 1.0 1.5 1.8 1.5 2.0 2.5 T =25, 85 C 5.0 12.0 15.0 T =-40 C 20.0 0.70 0.85 1.00 0.9 1.3 1.6 1.4 2.0 2.4 2.0 2.5 3.5 0.05 0.10 0.10 0.10 0.15 0.15 0.15 0.20 0.20 0.15 0.40 0.40 0.10 0.25 0.25 0.1 0.3 0.3 0.2 1.0 1.0 1.5 Unit Ω Ω Ω Ω 5.50 V IN =0 or V CC, I OUT =0 5 50 500 I CC Quiescent Supply Current 3.60 V IN =0 or V CC, I OUT =0 1 25 300 2.70 V IN =0 or V CC, I OUT =0 1 20 250 n 1.95 V IN =0 or V CC, I OUT =0 1 15 150 I CCT Increase in I CC per Control Input 4.5 to 5.5 sel=1.8 V 25 40 µ Notes: 3. On resistance is determined by the voltage drop between the and B pins at the indicated current through the switch. 4. R ON =R ON maximum R ON minimum; measured at identical V CC, temperature, and voltage. 5. Flatness is defined as the difference between the maximum and minimum value of on resistance over the specified range of conditions. FS1259 Rev. 1.0.8 5
C Electrical Characteristics ll typical values are at V CC =1.8 V, 2.5 V, 3.0 V, 5.0 V at 25 C unless otherwise specified. Symbol Parameter V CC (V) Conditions t ON t OFF Q Turn-On Time Turn-Off Time Charge Injection 4.50 to 5.50 OIRR Off-Isolation 1.8 to 5.0 Xtalk Crosstalk 1.8 to 5.0 BW THD -3 db Bandwidth Total Harmonic Distortion T =+25 C Min. Typ. Max. Min. Max. 1.0 4.0 7.5 1.0 9.0 3.00 to 3.60 1B or 2 B=V CC, 1.5 6.0 9.5 1.0 10.0 R L =50 Ω, 2.30 to 2.70 C L =35 pf 2.0 8.0 10.0 1.0 12.0 1.65 to 1.95 3.0 14.0 18.0 1.0 20.0 4.50 to 5.50 4.5 13.0 17.0 3.5 20.0 3.00 to 3.60 2.30 to 2.70 1B or 2B=V CC, R L =50 Ω, C L =35 pf 4.5 4.5 13.5 16.0 17.0 20.0 3.0 3.0 20.0 23.0 1.65 to 1.95 5.0 24.0 33.0 4.0 36.0 4.50 to 5.50 15 3.00 to 3.60 2.30 to 2.70 C L =1.0 nf, V GEN =0 V, R GEN =0 Ω 11 8 1.65 to 1.95 6 f=1 MHz, R L =50 Ω f=1 MHz, R L =50 Ω 4.50 to 5.50 240 3.00 to 3.60 240 R L =50 Ω 2.30 to 2.70 240 1.65 to 1.95 240 T =-40 to +85 C Unit Figure ns Figure 11 ns Figure 11 pc Figure 13-60 db Figure 12-73 db Figure 12 MHz Figure 15 1.8 R L =600,.003 Figure 16 V IN =0.5 V PP, % f=20 Hz to 5.0 20 khz.001 Figure 16 Capacitance Symbol Parameter V CC (V) Conditions C IN Control Pin Input Capacitance 0 C OFF B Port Off Capacitance 1.65 to 5.50 C ON Port On Capacitance 1.65 to 5.50 f=1 MHz Figure 14 f=1 MHz Figure 14 f=1 MHz Figure 14 T =+25 C Min. Typ. Max. Unit 3 pf 21 pf 47 pf FS1259 Rev. 1.0.8 6
Typical Performance Characteristics RON (Ohms) R ON (Ohms) Gain (db) 1.10 1.00 0.90 0.80 0.70 0.60 0.50 0.40 0.30 0.20 85 C 25 C -40 C 0.10-1.00 0.00 1.00 2.00 3.00 4.00 5.00 1.60 1.50 1.40 1.30 1.20 1.10 1.00 0.90 0.80 0.70 0.60 0.50 V IN (V) R ON (Ohms) 1.40 1.30 1.20 1.10 1.00 0.90 0.80 0.70 0.60 0.50 85 C 25 C -40 C 0.40-1.00 0.00 1.00 2.00 3.00 4.00 V IN (V) Figure 3. On Resistance (V CC =4.5 V) Figure 4. On Resistance (V CC =3.0 V) 0.40-0.50 0.00 0.50 1.00 1.50 2.00 2.50 3.00 0-1 -2-3 -4-5 -6-7 -8 V IN (V) 85 C 25 C -40 C R ON (Ohms) 14.00 12.00 10.00 8.00 6.00 4.00 2.00 25 C 85 C 0.00-0.50 0.00 0.50 1.00 1.50 2.00 V IN (V) Figure 5. On Resistance (V CC =2.3 V) Figure 6. On Resistance (V CC =1.65 V) 1 10 100 1000 10000 Frequency (MHz) Figure 7. Frequency Response (V CC =5.5 V, C L =0 pf) Off Isolation (db) -10-30 -50-70 Gain (db) 0-1 -2-3 -4-5 -6-7 -8-40 C 1 10 100 1000 10000 Frequency (MHz) Figure 8. Frequency Response (V CC =3.3 V, C L =0 pf) THD (%) 0.0040 0.0035 0.0030 0.0025 0.0020 0.0015 0.0010 0.0005 V CC =1.8V V CC =5.0V -90 0 1 10 100 Frequency (MHz) 0.0000 10 100 1000 10000 Frequency (MHz) Figure 9. Frequency Response (V CC =5.0 V, C L =0 pf) Figure 10. Total Harmonic Distortion FS1259 Rev. 1.0.8 7
Test Diagrams V B 1B or 2B S V CC R L 50 C L includes fixture and stray capacitance. 0 or V CC S V CC 50 1B V CC 10nF 2B V OUT C L 35pF Figure 11. V IN V OUT Figure 12. Control Input Switch Output 0V 0V V CC V OUT Turn On / Off Timing MES Network nalyzer 50 50 50 50 50% t ON t R = t F = 2.5ns t OFF 0.9 x V OUT 0.9 x V OUT Logic input waveforms inverted for switches that have the opposite logic sense. REF Off Isolation and Crosstalk OFF ISOLTION = 20log V OUT V IN ON-LOSS = 20log V OUT V IN CROSSTLK = 20log V OUT V IN V CC V GEN R GEN 1B or 2B C L V OUT V OUT ΔV OUT In S Off On Off Control Input In Off On Q = (ΔV OUT ) (C L ) Off Figure 13. Charge Injection FS1259 Rev. 1.0.8 8
Test Diagrams (Continued) Signal Generator 0dBm V IN Logic Input 0V or V CC 10nF B N S VCC Capacitance Meter f = 1MHz Figure 14. 50 10nF V+ 1B or 2B S 0V or V CC On / Off Capacitance Measurement Setup nalyzer Signal Generator 0dBm V IN Logic Input 0V or V CC 10nF B N S V CC R L nalyzer Figure 15. Bandwidth Figure 16. Harmonic Distortion FS1259 Rev. 1.0.8 9
Physical Dimensions 0-8 0.15 3.20 3.00 PIN 1 IDENT SETING PLNE 1.55 0.50 8 2.10 1.90 1 4 TOP VIEW 0.90 MX SIDE VIEW 0.4 TYP 5 B 2.40 2.20 0.2 C B LL LED TIPS 0.80 0.60 0.10 0.00 LL LED TIPS 0.1 C C 0.17-0.27 (8X) 0.13 B C GGE PLNE 0.12 1.80 (8X) 0.70 2.70 3.40 1.00 0.50 0.30 (8X) RECOMMENDED LND PTTERN. CONFORMS TO JEDEC REGISTRTION MO-187 B. DIMENSIONS RE IN MILLIMETERS. C. DIMENSIONS RE EXCLUSIVE OF BURRS, MOLD FLSH, ND TIE BR EXTRUSIONS. D. DIMENSIONS ND TOLERNCES PER NSI Y14.5M, 1994. E. FILE DRWING NME : MKT-MB08rev4 DETIL 0.10-0.18 0.20-0.35 SETING PLNE DETIL Figure 17. 8-Lead US8, JEDEC MO-187, Variation C, 3.0 mm Wide Package Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. lways visit Fairchild Semiconductor s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. http://www.fairchildsemi.com/dwg/m/mb08.pdf For current packing container specifications, visit Fairchild Semiconductor s online packaging area: http://www.fairchildsemi.com/packing_dwg/pkg-mb08_hnbk.pdf FS1259 Rev. 1.0.8 10
FS1259 Rev. 1.0.8 11
Mouser Electronics uthorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Fairchild Semiconductor: FS1259K8X