Daa Shee Programmable DC Elecronic Loads The programmable DC elecronic loads provide he performance of modular sysem DC elecronic loads in a compac benchop form facor. Wih fas ransien operaion speeds and high 16-bi measuremen resoluion, hese sandalone DC loads can be used for esing and evaluaing a variey of DC sources such as DC power supplies, DC-DC converers, baeries, baery chargers, and phoovolaic arrays. The DC loads can operae in consan curren (CC), consan volage (CV), consan resisance (CR), or consan power (CW) mode and be configured o provide a dynamically changing load o he DC source wih fas load swiching imes. Versaile inernal, exernal, and remoe riggering opions allow he dynamic load behavior o be synchronized wih oher evens. Increase produciviy by saving your es parameers ino any one of he 100 memory areas for quick sysem recall. ll load parameers such as volage, curren, slew rae, and widh can be se via he fron panel or programmed remoely. The provides sandard USB (USBTMC-complian), GPIB, or RS-232 serial inerfaces for remoe communicaion. To ensure he reliabiliy of your esing, he 8600 Series provides a power-on sysem self-es and numerous proecion feaures: overemperaure (OTP), overvolage (OVP), overcurren (OCP), overpower (OPP), and local/remoe reverse volage (LRV/RRV) proecion. Special pplicaions The provides a buil-in baery es mode o measure he ampere-hour (h) characerisic of a baery and a unique CR-LED mode o simulae he loading behavior of a ypical LED. Model 8600 8601 8602 8610 8612 8614 8616 Power 150 W 250 W 200 W 750 W 750 W 1500 W 1200 W Operaing Volage 0 120 V 0 120 V 0 500 V 0 120 V 0 500 V 0 120 V 0 500 V Raed Curren 0 30 0 60 0 15 0 120 0 30 0 240 0 60 Feaures Volage range up o 500 V Curren range up o 240 CC/CV/CR/CW operaing modes 16-bi volage and curren measuremen sysem providing 1 mv / 0.1 m resoluion Transien mode up o 25 khz in CC mode Lis mode funcion Sore and recall up o 100 seups djusable slew rae in CC mode Flexible riggering opions via fron panel, exernal inpu, imer, or bus Buil-in baery es funcion wih volage level, capaciy level, and imer sop condiions Tes modes o validae he OCP/OPP proecion funcions of a power supply CR-LED mode o simulae he loading behavior of ypical LEDs Remoe sense nalog curren conrol and monioring Thermosaically conrolled fan Sandard USB (USBTMC-complian), RS232, and GPIB inerfaces supporing SCPI commands for remoe conrol OVP/OCP/OPP/OTP including local and remoe reverse volage (LRV/RRV) proecion Compac 19 half-rack form facor allows for side-by-side rack mouning of wo unis (models 8600, 8601 and 8602) Technical daa subjec o change B&K Precision Corp. 2015
Models 8600, 8601 & 8602 Fron panel Brigh dual-line display The display shows boh measured inpu values and se parameers simulaneously. Roary conrol knob High curren es lead accessory model TLPWR1 Numeric keypad Funcion keys Cursor keys Load inpu erminal Inuiive user inerface The numeric keys and roary knob provide a convenien inerface for seing he operaing mode and desired curren, volage, and resisance levels quickly and precisely. Rear panel Cooling fan RS-232 inerface USB inerface GPIB inerface Curren monior BNC oupu Oupus a 0-10 V signal ha follows 0-full range of he inpu curren. I/O erminal block Exernal rigger, exernal analog programming, exernal inpu On/Off conrol, volage faul pin, and remoe sense erminals Line volage selecor 2
Models 8610, 8612, 8614 & 8616 Fron panel Power swich Brigh dual-line display The display shows boh measured inpu values and se parameers simulaneously. Operaing mode keys Cursor keys Funcion keys Numeric keypad Rear panel Inpu erminals Curren monior BNC oupu Oupus a 0-10 V signal ha follows 0-full range of he inpu curren. RS-232 inerface USB inerface GPIB inerface Line volage selecor C line inpu Cooling fan I/O erminal block Exernal rigger, exernal analog programming, exernal inpu On/Off conrol, volage faul pin, and remoe sense erminals Inpu fuse holder 3
Flexible operaion Transien operaion Lis mode uomaic es mode No limied o jus swiching beween wo levels, lis mode les you generae more complex sequences of inpu changes wih several differen levels. Up o 7 groups of lis files can be saved and execued in CC mode via inernal or exernal rigger. Each lis can conain up o 84 seps wih varying slew raes and a minimum widh ime of 20 μs per sep. Low volage operaion The can operae a low volages for applicaions such as fuel cell and solar cell esing. I level B level Slew Rae Transien operaion enables he load o periodically swich beween wo load levels (/B). power supply s regulaion and ransien characerisic can be evaluaed by monioring he supply s oupu volage under varying combinaions of load levels, duy cycle, and slew rae. The can simulae hese condiions in CC, CV, CW, and CR mode. Trigger 0 1 2 3 4 5 6 7 8 Seps CC 1 pass CV 3 V fail The can execue muliple es sequences in auomaic es mode. Up o 100 differen sequences can be linked o run seps of various operaing modes and loading condiions. Each sequence can also be programmed wih upper and lower limi Pass/Fail crieria. When applied in producion esing, you can easily judge wheher he es parameers of your devices are wihin he specificaion limis and adjus your process according o he Pass/Fail verdic. CR-LED mode CW 0.5 W pass CR 2 Ω pass 1 s 0.5 s 1.5 s 2.5 s 240 8614 I Io Rd Curren () 120 60 8610 8601 8616 Vd LED I-V Curve Vo Vd = Forward volage of he LED Rd = LED operaing resisance Vo = LED operaing volage Io = LED operaing curren V 30 0 8600 8612 8602 1 2 3 4 5 Volage (V) V Use he load s unique CR-LED operaing mode o es LED drivers. This funcion allows users o configure he LED s operaing resisance and forward volage o simulae he loading behavior of ypical LEDs. Typical minimum operaing volage a full scale curren 8600 8601 8602 8610 8612 8614 8616 1.1 V 1.1 V 4.5 V 1.2 V 3.6 V 1.5 V 3.6 V 4
Remoe conrol and programming Powerful communicaion inerfaces The provides sandard GPIB, USB, and RS232 inerfaces for remoe communicaion. These inerfaces offer SCPI and USBTMC sandard communicaion proocols o conrol your elecronic load from a PC. Exernal analog programming and monioring inerface In addiion o fron panel and remoe inerface conrol, curren values can also be programmed wih an analog conrol signal. The elecronic loads can be exernally conrolled from zero o full scale wih a 0-10 V inpu signal. BNC oupu is available on he rear for monioring he curren wih a 0-10 V oupu signal. pplicaion sofware Vols Baery es funcion 1.8 1.6 1.4 1.2 1.0 0.8 0.6 Typical baery discharge curve 0.4 0 0.5 1.0 1.5 2.0 2.5 Hours The buil-in baery es funcion uses CC mode o calculae he baery capaciy using a fixed curren load discharge. Users can specify cu-off volage level, capaciy level, and ime sop condiions. Buil-in rise and fall ime measuremen display Volage-on (Von) lach operaion V Von Level Load Sink Curren Rise Rae /µs Conrol he inpu urn on sae for he DC elecronic load by configuring he Von lach funcion. This can be used o sar and sop discharging of a baery or oher power source a a specified volage level. Oscilloscope display PC sofware is provided for fron panel emulaion, generaing and execuing es sequences, or logging measuremen daa wihou he need o wrie source code. ddiionally, his applicaion sofware inegraes wih NI Daa Dashboard for LabVIEW apps, which allows users o creae a cusom dashboard on a able compuer or smarphone o remoely monior DC loads via his PC sofware. Remoe monioring on ios, ndroid or Windows 8 compaible ables or smarphones via NI Daa Dashboard for LabVIEW apps Log volage, curren, and power values wih imesamp Run ransien operaion and lis mode programs remoely Creae an unlimied number of exernal lis files o be execued from PC memory djusable slew rae The can measure he rise or fall ime from a specified sar and sop volage level of he measured inpu wihou he need for an oscilloscope. This funcion can also be used as an inernal imer o coun how long he inpu has been enabled. Slew Rae In CC mode, users can conrol he rae or slope of he change in curren in a ransien response es. Se he slew rae o as slow as 0.001 /ms or as fas as 2.5 /µs depending on he model and seleced curren range. 5
Specificaions Model 8600 8601 8602 8610 8612 8614 8616 Inpu raings Inpu volage 0 120 V 0 120 V 0 500 V 0 120 V 0 500 V 0 120 V 0 500 V Inpu curren Minimum operaing volage CV mode Resoluion CC mode Resoluion CR mode Low 0 3 0 6 0 3 0 12 0 3 0 24 0 6 High 0 30 0 60 0 15 0 120 0 30 0 240 0 60 Inpu power 150 W 250 W 200 W 750 W 1500 W 1200 W Resoluion Low 0.11 V a 3 0.18 V a 6 1 V a 3 0.12 V a 12 0.36 V a 3 0.15 V a 24 0.36 V a 6 High 1.1 V a 30 1.1 V a 60 4.5 V a 15 1.2 V a 120 3.6 V a 30 1.5 V a 240 3.6 V a 60 Low 0 18 V 0 50 V 0 18 V 0 50 V 0 18 V 0 50 V High 0 120 V 0 500 V 0 120 V 0 500 V 0 120 V 0 500 V Low 0.1 mv 1 mv 0.1 mv 1 mv 0.1 mv 1 mv High 1 mv 10 mv 1 mv 10 mv 1 mv 10 mv Low High 0.02% FS) Low 0 3 0 6 0 3 0 12 0 3 0 24 0 6 High 0 30 0 60 0 15 0 120 0 30 0 240 0 60 Low 0.01 m 0.1 m 1 m 0.1 m 1 m 0.1 m High 0.1 m 1 m 10 m 1 m 10 m 1 m Low 0.1% FS) 0.1% FS) High 0.1% FS) 0.1% FS) Low 0.05 Ω 10 Ω 0.3 Ω 10 Ω 0.02 Ω 10 Ω 0.15 Ω 10 Ω 0.01 Ω 10 Ω 0.01 Ω 10 Ω High Low High 10 Ω - 7.5 kω 16 bi 0.01%+0.08 S 0.01%+0.0008 S CW mode 150 W 250 W 200 W 750 W 1500 W 1200 W Resoluion 10 mw 100 mw 0.1% + 0.1% FS 0.2% + 0.2% FS 0.1% + 0.1% FS 0.2% + 0.2% FS Transien mode (CC mode) T1 & T2 (1) 20 µs 3600 s / Resoluion: 10 µs 5 µs + 100 ppm (2) Low 0.001-2.5 /ms 0.001-1 /ms 0.001-0.25 /µs 0.0001-0.1 /µs 0.001-0.25 /µs 0.0001-0.1 /µs Slew Rae High 0.001-2.5 /µs 0.001-1 /µs 0.01-2.5 /µs 0.001-1 /µs 0.01-2.5 /µs 0.001-1 /µs (1) Fas pulse rains wih large ransiions may no be achievable. (2) The slew rae specificaions are no warraned, bu are descripions of ypical performance. The acual ransiion ime is defined as he ime for he inpu o change from 10% o 90%, or vice versa, of he programmed curren values. In case of very large load changes, e.g. from no load o full load, he acual ransiion ime will be larger han he expeced ime. The load will auomaically adjus he slew rae o fi wihin he range (high or low) ha is closes o he programmed value. 6
Model 8600 8601 8602 8610 8612 8614 8616 Readback volage Resoluion Low 0 18 V 0 18 V 0 50 V 0 18 V 0 50 V 0 18 V 0 50 V High 0 120 V 0 120 V 0 500 V 0 120 V 0 500 V 0 120 V 0 500 V Low 0.1 mv 1 mv 0.1 mv 1 mv 0.1 mv 1 mv High 1 mv 10 mv 1 mv 10 mv 1 mv 10 mv Readback curren Resoluion Readback power Low 0 3 0 6 0 3 0 12 0 3 0 24 0 6 High 0 30 0 60 0 15 0 120 0 30 0 240 0 60 Low 0.01 m 0.1 m 0.01 m 1 m 0.1 m 1 m 0.1 m High 0.1 m 1 m 0.1 m 10 m 1 m 10 m 1 m 0.1% FS) 0.1% FS) 0.1% FS) 150 W 250 W 200 W 750 W 1500 W 1200 W Resoluion 10 mw 100 mw ±(1%+0.1% FS) ±(0.2%+0.2% FS) ±(0.1%+0.1% FS) ±(0.2%+0.2% FS) Proecion range (ypical) OCP General (ypical) Shor circui Curren (CC) OPP 150 W 250 W 200 W 760 W 1550 W 1250 W Low 3.3 6.6 3.3 13.2 3.3 26.4 6.6 High 33 66 16.5 132 33 264 66 OVP 120 V 120 V 500 V 130 V 530 V 130 V 530 V OTP 185 ºF (85 C) Low 3 6 3 12 3 24 6 High 30 60 15 120 30 240 60 Volage (CV) 0 V Resisance (CR) 35 mω 30 mω 300 mω 10 mω 120 mω 6 mω 60 mω Inpu erminal impedance 150 kω 300 kω 1 MΩ 300 kω 1 MΩ 300 kω 1 MΩ C inpu 110 V/220 V ±10%, 50/60 Hz Operaing emperaure 32 ºF o 104 ºF (0 C o 40 C) Sorage emperaure 14 ºF o 140 ºF (-10 C o 60 C) Humidiy Indoor use, 95% Safey EN61010-1:2001, EU Low Volage Direcive 2006/95/EC Elecromagneic compaibiliy Mees EMC Direcive 2004/108/EC, EN 61000-3-2:2006, EN 61000-3-3:1995+1:2001+2:2005 EN 61000-4-2/-3/-4/-5/-6/-11, EN 61326-1:2006 Dimensions (W x H x D) 8.5 x 3.5 x 15.2 (218 x 90 x 387 mm) 19 x 5.8 x 24.5 (485 x 147 x 621 mm) Weigh 9.9 lbs (4.5 kg) 54 lbs (24.6 kg) Sandard accessories User manual, power cord, cerificae of calibraion & es repor Opional accessories TLPWR1 high curren es leads, IT-E151 rackmoun ki (models 8600, 8601, and 8602 only) 7 v102615