NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1Multiplexer / De-multiplexer Bus witch Features Useful in Both nalog and Digital pplications pace-aving, C7 6-Lead urface Mount Package Ultra-mall, MicroPak Leadless Package Low On Resistance: <1Ω on Typical at 3.3 Broad Operating Range: 1.65 to 5.5 Rail-to-Rail ignal Handling Power-Down, High-Impedance Control Over-oltage Tolerance of Control to 7. Break-Before-Make Enable Circuitry 25MHz, 3dB Bandwidth Ordering Information Part Number Description Top Mark Eco tatus Package Description The NC7B3157 / F3157 is a high-performance, single-pole / double-throw (PDT) analog switch or 2:1 multiplexer / de-multiplexer bus switch. The device is fabricated with advanced sub-micron CMO technology to achieve high-speed enable and disable times and low on resistance. The break-beforemake select circuitry prevents disruption of signals on the B Port due to both switches temporarily being enabled during select pin switching. The device is specified to operate over the 1.65 to 5.5 operating range. The control input tolerates voltages up to 5.5, independent of the operating range. NC7B3157P6X B7 RoH 6-Lead, C7, EIJ C88, 1.25mm Wide Package NC7B3157L6X BB RoH 6-Lead, MicroPak 1.mm Wide Package F3157P6X B7 RoH 6-Lead, C7, EIJ C88, 1.25mm Wide Package F3157L6X BB RoH 6-Lead, MicroPak 1.mm Wide Package Packing Method 3 Units on Tape and Reel 5 Units on Tape and Reel 3 Units on Tape and Reel 5 Units on Tape and Reel NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch 26 emiconductor Components Industries, LLC. October-217, Rev. 2 Publication Order Number: NC7B3157/D
Logic ymbol B 1 nalog ymbol Function Table () Function Logic Level Low B Connected to Logic Level High B 1 Connected to Pin Descriptions Figure 1. Logic ymbol B B 1 B Figure 3. nalog ymbol Pin Names Description, B, B 1 Data Ports Control Connection Diagrams 2. Pin ssignments C7 Figure 4. Pin One Orientation Note: Orientation of top mark determines pin one location. Read the top product code mark left to right and pin one is the lower left pin (see Figure 4). B 1 B 1 2 3 4 Figure 5. Pad ssignments for MicroPak 6 5 NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch 2
bsolute Maximum Ratings tresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. ymbol Parameter Min. Max. Unit upply oltage.5 +7. DC witch oltage (1).5 +.5 IN DC oltage (1).5 +7. I IK DC Diode Current at IN < 5 m I OUT DC Output Current 128 m I CC /I DC or Ground Current ±1 m T TG torage Temperature Range 65 +15 C T J Junction Temperature Under Bias +15 C T L Junction Lead Temperature (oldering, 1 seconds) +26 C ML Moisture ensitivity Level (JEDEC J-TD-2) 1 Level P D Power Dissipation at +85 C 18 mw ED Human Body Model, JED22-114 4 Note: 1. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. ON emiconductor does not recommend exceeding them or designing to absolute maximum ratings. ymbol Parameter Min. Max. Unit upply oltage Operating 1.65 5.5 IN Control oltage (2) IN witch oltage (2) OUT Output oltage (2) T Operating Temperature 4 +85 C t r, t f Rise and Fall Time Control = 2.3 3.6 1 ns/ Control = 4.5 5.5 5 ns/ θ J Thermal Resistance, C7 27 C/W Note: 2. Control input must be held HIGH or LOW; it must not float. NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch 3
DC Electrical Characteristics ymbol Parameter Conditions () IH IL I IN I OFF R ON I CC R RNGE ΔR ON R flat High Level oltage Low Level oltage Leakage Current Off tate Leakage Current witch On Resistance (3) Quiescent upply Current; ll Channels On or Off nalog ignal Range On Resistance Over (3, 7) ignal Range On Resistance Match Between- (3, 4, 5) Channels On Resistance (3, 4, 6) Flatness T T = +25 C = 4 C to +85 C Min. Typ. Max. Min. Max. Notes: 3. Measured by the voltage drop between and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two ( or B Ports). 4. Parameter is characterized, but not tested in production. 5. ΔR ON = R ON max R ON minimum measured at identical, temperature, and voltage levels. 6. Flatness is defined as the difference between the maximum and minimum value of on resistance over the specified range of conditions. 7. Guaranteed by design. Units 1.65 1.95.75.75 2.3 5.5.7.7 1.65 1.95.25.25 2.3 5.5.3.3 IN 5.5 5.5 ±.5 ±.1 ±1 µ, B 1.65 5.5 ±.5 ±.1 ±1 µ IN =, I O = 3m 4.5 3. 7. 7. IN = 2.4, I O = 3m 5. 12. 12. IN = 4.5, I O = 3m 7. 15. 15. IN =, I O = 24m 3. 4. 9. 9. IN = 3, I O = 24m 1. 2. 2. IN =, I O = 8m 2.3 5. 12. 12. IN = 2.3, I O = 8m 13. 3. 3. IN =, I O = 4m 1.65 6.5 2. 2. IN = 1.65, I O = 4m 17. 5. 5. IN = or I OUT = 5.5 1 1 µ I = 3m, Bn 4.5 25. I = 24m, Bn 3. 5. I = 8m, Bn 2.3 1 I = 4m, Bn 1.65 3 I = 3m, Bn = 3.15 4.5.15 I = 24m, Bn 2.1 3..2 I = 8m, Bn = 1.6 2.3.5 I = 4m, Bn = 1.15 1.65.5 I = 3m, Bn 5. 6. I = 24m, Bn 3.3 12. I = 8m, Bn 2.5 28. I = 4m, Bn 1.8 125 Ω Ω Ω Ω NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch 4
C Electrical Characteristics ymbol Parameter Conditions Notes: 8. This parameter is guaranteed by design but not tested. The bus switch contributes no propagation delay other than the RC delay of the on resistance of the switch and the 5pF load capacitance, when driven by an ideal voltage source (zero output impedance). 9. Guaranteed by design. 1. Off Isolation = 2 log 1 [ / Bn ]. Capacitance () T = +25 C, f = 1MHz. Capacitance is characterized, but not tested in production. T T = +25 C = 4 C to +85 C Units Figure Number Min. Typ. Max. Min. Max. 1.65 1.95 3.5 3.5 t PHL, Propagation Delay 2.3 2.7 1.2 1.2 Figure 12 t PLH Bus-to-Bus (8) I = OPEN ns 3. 3.6.8.8 Figure 13 4.5 5.5.3.3 1.65 1.95 7. 23. 7. 24. Output Enable Time t PZL, Turn-On Time I = 2 x for t 2.3 2.7 3.5 13. 3.5 14. PZL Figure 12 ns t PZH ( to B n ) I = for t PZH 3. 3.6 2.5 6.9 2.5 7.6 Figure 13 4.5 5.5 1.7 5.2 1.7 5.7 1.65 1.95 3. 12.5 3. 13. Output Disable Time t PLZ, Turn-Off Time I = 2 x for t 2.3 2.7 2. 7. 2. 7.5 Figure 12 PLZ ns Figure 13 t PHZ ( Port to B Port) I = for t PHZ 3. 3.6 1.5 5. 1.5 5.3 4.5 5.5.8 3.5.8 3.8 1.65 1.95.5.5 t B-M Break-Before-Make 2.3 2.7.5.5 Time (9) 3. 3.6.5.5 ns Figure 14 4.5 5.5.5.5 Q Charge Injection (9) C L =.1nF, GEN =, 5. 7. R GEN = Ω 3.3 3. pc Figure 15 OIRR Off Isolation (1) R L = 5Ω, f = 1MHz 1.65 5.5 57. db Figure 16 Xtalk Crosstalk R L = 5Ω, f = 1MHz 1.65 5.5 54. db Figure 17 BW 3dB Bandwidth R L = 5Ω 1.65 5.5 25 MHz Figure 2 THD Total Harmonic R L = 6Ω,.5 PP, Distortion (9) f = 6 Hz to 2 KHz 5..11 % ymbol Parameter Conditions Typ. Max. Units Figure Number C IN Control Pin Capacitance = 2.3 pf C IO-B B Port Off Capacitance = 5. 6.5 pf Figure 18 C IO-ON Port Capacitance When witch Is Enabled = 5. 18.5 pf Figure 19 NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch 5
Typical Characteristics Off Isolation (db) Crosstalk (db) Gain (db) -1 = 1.65-2 -3-4 -5-6 -7-8 -9-1 -11-12 -1 = 5.5-2 -3-4 -5-6 -7-8 -9-1 -11-12 Figure 6. Off Isolation, = 1.65 Figure 7. Off Isolation, = 5.5-1 = 1.65-2 -3-4 -5-6 -7-8 -9-1 -11-12 -1-2 -3-4 -5-6 -7 Figure 8. Crosstalk, = 1.65 Figure 9. Crosstalk, = 5.5 C L = pf = 1.65-8 Off Isolation (db) Crosstalk (db) Gain (db) -1 = 5.5-2 -3-4 -5-6 -7-8 -9-1 -11-12 -1-2 -3-4 -5-6 -7 C L = pf = 5.5-8 NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch Figure 1. Bandwidth, = 1.65 Figure 11. Bandwidth, = 5.5 6
C Loading and Waveforms t r = 2.5ns witch 1% Output IN Logic t PLH 9% 9% B B 1 t W FROM OUTPUT UNDER TET Figure 12. C Test Circuit Figure 13. C Waveforms Figure 14. Break-Before-Make Interval Timing C L I RU RD Notes: driven by 5Ω source terminated in 5Ω C L includes load and stray capacitance PRR = 1. MHz; t W = 5 ns 1% t PHL t r = 2.5ns R L OH OL C L OUT t r = 2.5ns Control Output Output t PZL t PZH 9% 9% 1% 1% Logic OUT t D t r = 2.5ns t PLZ OL +.3 OL t PHZ OH OH.3.9 x OUT TRI TRI NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch 7
C Loading and Waveforms (continued) R GEN OUT GE R L C L 1MΩ 1pF OUT Logic nalyzer Capacitance Meter f = 1MHz 5Ω 5Ω B N 1nF B N Figure 16. Off Isolation Figure 18. Channel Off Capacitance 1nF B N Logic Figure 15. Charge Injection Test Logic or IH ignal Generator dbm Logic or Logic or 1nF B N ignal Generator dbm nalyzer Capacitance Meter f = 1MHz OFF ON Q = (Δ OUT )(C L ) 5Ω 1nF B B 1 Figure 17. Crosstalk 1nF B N OFF Δ OUT Figure 19. Channel On Capacitance 5Ω Logic or 5Ω NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch Figure 2. Bandwidth 8
Physical Dimensions Figure 21. 6-Lead, C7, EIJ C88, 1.25mm Wide Package Package drawings are provided as a service to customers considering ON emiconductor components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a ON emiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of ON emiconductor s worldwide terms and conditions, specifically the warranty therein, which covers ON emiconductor products. NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch 9
Physical Dimensions 2X.5 C DETIL Notes:.5 C (.5) 6X 1. CONFORM TO JEDEC TNDRD M-252 RITION UD 2. DIMENION RE IN MILLIMETER 3. DRWING CONFORM TO ME Y14.5M-1994 MC6REC.55MX C 1.45 TOP IEW 1..5 BOTTOM IEW B 2X.5 C 6-Lead, MicroPak 1.mm Wide Package RECOMMENED LND PTTERN Package drawings are provided as a service to customers considering ON emiconductor components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a ON emiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of ON emiconductor s worldwide terms and conditions, specifically the warranty therein, which covers ON emiconductor products. 1..5..25.15 6X.35.25.4.3.5 C (.49) 5X (.52) 1X PIN 1.1 C B.5 C 5X 5X (.13) 4X.75 X 45 CHMFER (1) (.3) 6X.1. 6X.4.3 (.75).45.35 DETIL PIN 1 TERMINL NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1 Multiplexer / De-multiplexer Bus witch 1
ON emiconductor and are trademarks of emiconductor Components Industries, LLC dba ON emiconductor or its subsidiaries in the United tates and/or other countries. ON emiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. listing of ON emiconductor s product/patent coverage may be accessed at /site/pdf/patent Marking.pdf. ON emiconductor reserves the right to make changes without further notice to any products herein. ON emiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON emiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON emiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON emiconductor. Typical parameters which may be provided in ON emiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. ll operating parameters, including Typicals must be validated for each customer application by customer s technical experts. ON emiconductor does not convey any license under its patent rights nor the rights of others. ON emiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FD Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. hould Buyer purchase or use ON emiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON emiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON emiconductor was negligent regarding the design or manufacture of the part. ON emiconductor is an Equal Opportunity/ffirmative ction Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICTION ORDERING INFORMTION LITERTURE FULFILLMENT: Literature Distribution Center for ON emiconductor 19521 E. 32nd Pkwy, urora, Colorado 811 U Phone: 33 675 2175 or 8 344 386 Toll Free U/Canada Fax: 33 675 2176 or 8 344 3867 Toll Free U/Canada Email: orderlit@onsemi.com emiconductor Components Industries, LLC N. merican Technical upport: 8 282 9855 Toll Free U/Canada Europe, Middle East and frica Technical upport: Phone: 421 33 79 291 Japan Customer Focus Center Phone: 81 3 5817 15 ON emiconductor Website: Order Literature: http:///orderlit For additional information, please contact your local ales Representative