Applied directly to rust A smooth gloss anti-rust enamel paint for metal surfaces It prevents humidity from penetrating, providing long-lasting rust protection Highly resistant to ultraviolet radiation, yellowing and adverse weather conditions Strong adhesion even when applied directly to rusty metal surfaces High covering power and ease of application Delivery time for the painting project is considerably shorter, as no primer is required, surfaces can be recoated after 24 hours and paint is thinned with a paintbrush thinner (KRAFT White Spirit) without shrinking any former conventional paints It creates a smooth high-gloss finish A special high-gloss solvent-based paint for interior and exterior use. It can be applied directly to rusty surfaces without requiring minium or an anti-rust metal primer. Thanks to the special innovative composition of its resins and pigments, it inactivates rust and protects metal surfaces from corrosion caused by humidity, ultraviolet radiation and adverse weather conditions. Resistant to yellowing, it gives a smooth gloss finish. It retains its gloss and colour over a long period. For effective rust protection, the final dry film thickness must be more than 110Ìm, so at least two coats of paint are required.. Low volatile organic compound (VOC) product Ease of workability Even spreading Effective protection MADE IN E.U. DRUCKFARBEN HELLAS AEBEE, ASPROPYRGOS ATTIKI, GREECE TEL: +30 210 55 19 500 www.kraftpaints.gr - www.druckfarben.gr Contact / Order Line: 800 111 7700 (free of charge)
Surface Preparation & Application To ensure proper adhesion, the surface must be dry, clean and free of dust, fat, grease, salt, loose paint / rust, scale / patina, etc. Any preliminary work on painted surfaces in the form of fine sanding, flame cleaning, etc. may produce dangerous dust or spray mist. Work in a well ventilated area. Do not fail to use appropriate personal protective equipment. Filling / patching primed iron surfaces: The acrylic putty KRAFT SPACHTEL is recommended. On rusty metal surfaces: First, remove any loose rust or paint with a wire brush, clean and apply 2-3 coats of KRAFT METAL 3 in 1 SMOOTH GLOSS. On galvanised, zinc, aluminium, bronze, chrome or copper surfaces: fine sanding of patina, 1 coat of KRAFT RUST BLOCKER AQUA, and after 12 hours 2 coats of KRAFT METAL 3 in 1 SMOOTH GLOSS To ensure maximum rust protection in coastal or northern areas, it is recommended to apply 2 coats of KRAFT RUST BLOCKER AQUA first. eyes, rinse immediately with plenty of water and seek medical advice. In case of ingestion, seek medical advice immediately and show container or label. Toxic to aquatic organisms. It may cause long-term adverse effects in the aquatic environment. Do not empty remaining contents into drains or other water sources. Disposal of materials must be carried out responsibly and in accordance with applicable legislation. For more information, please refer to the Material Safety Data Sheet for this product. It contains ethyl methyl ketoxime and 2- ethylhexanoic cobalt. It may cause an allergic reaction. Poison Centre Tel.: 210-7793777. Storage Store product at temperatures between 5ÆC and 35ÆC and at a humidity rate < 50%. Keep cans hermetically closed. Paint Application Instructions Tools: paintbrush or roller (Ripolin), air or airless spray gun Cleaning: Immediately after use, clean tools and any paint residues with KRAFT Brush Thinner. Thinning: Paintbrush or roller: up to 10% by volume with KRAFT Brush Thinner Air spray gun: up to 13% by volume with Airless spray gun: up to 5% by volume with Dry to touch: 4-6 hours Dry to recoat, minimum: 24 hours Stir well before use and during application. Do not apply at temperatures below 5ÆC and above 35ÆC as well as at relative humidity levels above 65%. Pack Size Available in white, black and Index colours in 0.75lt and 2.5lt containers Instructions for Safe Use Flammable. Keep out of the reach of children. Use only in a well ventilated area. Do not inhale spray mist. Avoid contact with skin and eyes. Prolonged exposure may cause skin dryness or cracking. In case of contact with skin, wash off immediately with soap and water or with a suitable skin cleaner. In case of contact with Special one-component coatings (SB) (A/i) Phase I limit value: 600 gr/lt Phase II limit value: 500 gr/lt Maximum content of VOC of the product in a ready-to-use condition: 499 gr/lt Technical Characteristics Specific Gravity (Kg/l) (±0.02) Viscosity (cp) Solids by Volume (%) Specular Gloss (60Æ) White Colour Coordinates Theoretical Coverage (m 2 /l) Minimum Dry Film Thickness required (Ìm) Flash Point Shelf Life White 1.25 Black 1.01 Grey 1.22 Cypress Green 1.05 Brown 1.06 Yellow 1.09 Red 1.04 Blue 1.05 Mykonos Blue 1.01 Claret 1.04 Green 1.06 800-1.800 50 ± 2 {ISO 3251} 90 L>95 b<2 4-5* (2 coats) {ISO 6504} >110 28ÆC {DIN 53213} at least 1 year * depending on painting conditions and application method
Applied directly to rust A metallic gloss anti-rust enamel paint for metal surfaces It prevents humidity from penetrating, providing long-lasting rust protection Highly resistant to ultraviolet radiation, discoloration and adverse weather conditions Strong adhesion even when applied directly to rusty metal surfaces High covering power and ease of application Delivery time for the painting project is considerably shorter, as no primer is required, surfaces can be recoated after 24 hours and paint is thinned with a paintbrush thinner (KRAFT White Spirit) without shrinking any former conventional paints It creates a metallic gloss finish A special metallic-finish solvent-based gloss paint for interior and exterior use. It can be applied directly to rusty surfaces without requiring minium or an anti-rust metal primer, giving a metallic surface. Thanks to the special innovative composition of its resins and pigments, it inactivates rust and protects metal surfaces from corrosion caused by humidity, ultraviolet radiation and adverse weather conditions. Resistant to yellowing, it gives a metallic gloss finish. It retains its gloss and colour over a long period. For effective rust protection, the final dry film thickness must be more than 110Ìm, so at least two coats of paint are required. Low volatile organic compound (VOC) product Ease of workability Even spreading Effective protection MADE IN E.U. DRUCKFARBEN HELLAS AEBEE, ASPROPYRGOS ATTIKI, GREECE TEL: +30 210 55 19 500 www.kraftpaints.gr - www.druckfarben.gr Contact / Order Line: 800 111 7700 (free of charge)
Surface Preparation & Application To ensure proper adhesion, the surface must be dry, clean and free of dust, fat, grease, salt, loose paint / rust, scale / patina, etc. Any preliminary work on painted surfaces in the form of fine sanding, flame cleaning, etc. may produce dangerous dust or spray mist. Work in a well ventilated area. Do not fail to use appropriate personal protective equipment. Filling / patching primed iron surfaces: The acrylic putty KRAFT SPACHTEL is recommended. On rusty metal surfaces: First, remove any loose rust or paint with a wire brush, clean and apply 2-3 coats of KRAFT METAL 3 in 1 METALLIC GLOSS. On galvanised, zinc, aluminium, bronze, chrome or copper surfaces: fine sanding of patina, 1 coat of KRAFT RUST BLOCKER AQUA, and after 12 hours 2 coats of KRAFT METAL 3 in 1 METALLIC GLOSS To ensure maximum rust protection in coastal or northern areas, it is recommended to apply 2 coats of KRAFT RUST BLOCKER AQUA first. Paint Application Instructions Tools: paintbrush or roller (Ripolin), air or airless spray gun Cleaning: Immediately after use, clean tools and any paint residues with KRAFT Brush Thinner. Thinning: Paintbrush or roller: up to 5% by volume with KRAFT Brush Thinner Air spray gun: up to 5% by volume with Airless spray gun: up to 5% by volume with Dry to touch: 4-6 hours Dry to recoat, minimum: 24 hours Stir well before use and during application. Do not apply at temperatures below 5ÆC and above 35ÆC as well as at relative humidity levels above 65%. Pack Size Available in Index colours in 0.75lt containers Instructions for Safe Use Flammable. Keep out of the reach of children. Use only in a well ventilated area. Do not inhale spray mist. Avoid contact with skin and eyes. Prolonged exposure may cause skin dryness or cracking. In case of contact with skin, wash off immediately with soap and water or with a suitable skin cleaner. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. In case of ingestion, seek medical advice immediately and show container or label. Toxic to aquatic organisms. It may cause long-term adverse effects in the aquatic environment. Do not empty remaining contents into drains or other water sources. Disposal of materials must be carried out responsibly and in accordance with applicable legislation. For more information, please refer to the Material Safety Data Sheet for this product. It contains ethyl methyl ketoxime and 2- ethylhexanoic cobalt. It may cause an allergic reaction. Poison Centre Tel.: 210-7793777. Storage Store product at temperatures between 5ÆC and 35ÆC and at a humidity rate < 50%. Keep cans hermetically closed. Special one-component coatings (SB) (A/i) Phase I limit value: 600 gr/lt Phase II limit value: 500 gr/lt Maximum content of VOC of the product in a ready-to-use condition: 499 gr/lt Technical Characteristics Specific Gravity (Kg/l) (±0.02) Viscosity (cp) Solids by Volume (%) Theoretical Coverage (m 2 /l) Minimum Dry Film Thickness required (Ìm) Flash Point Shelf Life Carbon Grey 0.99 Silver 0.99 Grey Blue 0.99 Brick Red 1.01 Green 0.99 Copper 1.01 Gold 0.99 700-2.000 46,5 ± 2 {ISO 3251} 4-5* (2 coats) {ISO 6504} 110 28ÆC {DIN 53213} at least 1 year * depending on painting conditions and application method
Applied directly to rust A metallic flat anti-rust enamel paint for metal surfaces It prevents humidity from penetrating, providing long-lasting rust protection Highly resistant to ultraviolet radiation, discoloration and adverse weather conditions Strong adhesion even when applied directly to rusty metal surfaces High covering power and ease of application It creates a metallic flat textured enamel finish with excellent iridescence An alkyd metallic-finish, flat-gloss, solventbased paint for interior and exterior use. It can be applied directly to rusty surfaces without requiring minium or an anti-rust metal primer. Thanks to the special innovative composition of its resins and pigments, it inactivates rust and protects metal surfaces from corrosion caused by humidity, ultraviolet radiation and adverse weather conditions. Resistant to yellowing, it gives a metallic finish. It retains its gloss and colour over a long period. For effective rust protection, the final dry film thickness must be more than 110Ìm, so at least 2-3 coats of paint are required. Low volatile organic compound (VOC) product Ease of workability Even spreading Effective protection MADE IN E.U. DRUCKFARBEN HELLAS AEBEE, ASPROPYRGOS ATTIKI, GREECE TEL: +30 210 55 19 500 www.kraftpaints.gr - www.druckfarben.gr Contact / Order Line: 800 111 7700 (free of charge)
Surface Preparation & Application To ensure proper adhesion, the surface must be dry, clean and free of dust, fat, grease, salt, loose paint / rust, scale / patina, etc. Any preliminary work on painted surfaces in the form of fine sanding, flame cleaning, etc. may produce dangerous dust or spray mist. Work in a well ventilated area. Do not fail to use appropriate personal protective equipment. Filling / patching primed iron surfaces: The acrylic putty KRAFT SPACHTEL is recommended. On rusty metal surfaces: First, remove any loose rust or paint with a wire brush, clean and apply 2-3 coats of KRAFT METAL 3 in 1 METALLIC FLAT. On galvanised, zinc, aluminium, bronze, chrome or copper surfaces: fine sanding of patina, 1 coat of KRAFT RUST BLOCKER AQUA, and after 12 hours 2 coats of KRAFT METAL 3 in 1 METALLIC FLAT To ensure maximum rust protection in coastal or northern areas, it is recommended to apply 2 coats of KRAFT RUST BLOCKER AQUA first. immediately with soap and water or with a suitable skin cleaner. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. In case of ingestion, seek medical advice immediately and show container or label. Toxic to aquatic organisms. It may cause long-term adverse effects in the aquatic environment. Do not empty remaining contents into drains or other water sources. Disposal of materials must be carried out responsibly and in accordance with applicable legislation. For more information, please refer to the Material Safety Data Sheet for this product. It contains ethyl methyl ketoxime and 2- ethylhexanoic cobalt. It may cause an allergic reaction. Poison Centre Tel.: 210-7793777. Storage Store product at temperatures between 5ÆC and 35ÆC and at a humidity rate < 50%. Keep cans hermetically closed. Paint Application Instructions Tools: paintbrush or roller (Ripolin), air or airless spray gun Cleaning: Immediately after use, clean tools and any paint residues with KRAFT Brush Thinner. Thinning: Paintbrush or roller: up to 10% by volume with KRAFT Brush Thinner Air spray gun: up to 10% by volume with Airless spray gun: up to 5% by volume with Dry to touch: 4-6 hours Dry to recoat, minimum: 24 hours Stir well before use and during application. Do not apply at temperatures below 5ÆC and above 35ÆC as well as at relative humidity levels above 65%. Pack Size Available in Index colours in 0.75L containers. Instructions for Safe Use Flammable. Keep out of the reach of children. Use only in a well ventilated area. Do not inhale spray mist. Avoid contact with skin and eyes. Prolonged exposure may cause skin dryness or cracking. In case of contact with skin, wash off Special one-component coatings (SB) (A/i) Phase I limit value: 600 g/l Phase II limit value: 500 g/l Maximum content of VOC of the product in a ready-to-use condition: 499 g/l Technical Characteristics Specific Gravity (Kg/L) (±0.02) Viscosity (cp) Solids by Volume (%) Theoretical Coverage (m 2 /l) Minimum Dry Film Thickness required (Ìm) Flash Point Shelf Life Carbon Grey 1.43 Silver 1.42 Grey Blue 1.43 Brick Red 1.45 Green 1.43 Copper 1.47 Gold 1.47 2.800-4.500 52,5 ± 2 {ISO 3251} 4-5* (2 coats) {ISO 6504} 110 28ÆC {DIN 53213} at least 1 year * depending on painting conditions and application method
Applied directly to rust An anti-rust wrought-surface enamel paint for metal surfaces It prevents humidity from penetrating, providing long-lasting rust protection Highly resistant to ultraviolet radiation, discoloration and adverse weather conditions Strong adhesion even when applied directly to rusty metal surfaces High covering power and ease of application It creates a gloss wrought finish An alkyd solvent-based paint for interior and exterior use. It can be applied directly to rusty surfaces, giving an appearance of wrought metal, without requiring minium or an anti-rust metal primer. Thanks to the special innovative composition of its resins and pigments, it inactivates rust and protects metal surfaces from corrosion caused by humidity, ultraviolet radiation and adverse weather conditions. Resistant to yellowing, it gives a wrought finish. It retains its gloss and colour over a long period and gives a wrought finish. For effective rust protection, the final dry film thickness must be more than 110Ìm, so at least 2-3 coats of paint are required. Low volatile organic compound (VOC) product Ease of workability Even spreading Effective protection MADE IN E.U. DRUCKFARBEN HELLAS AEBEE, ASPROPYRGOS ATTIKI, GREECE TEL: +30 210 55 19 500 www.kraftpaints.gr - www.druckfarben.gr Contact / Order Line: 800 111 7700 (free of charge)
Surface Preparation & Application To ensure proper adhesion, the surface must be dry, clean and free of dust, fat, grease, salt, loose paint / rust, scale / patina, etc. Any preliminary work on painted surfaces in the form of fine sanding, flame cleaning, etc. may produce dangerous dust or spray mist. Work in a well ventilated area. Do not fail to use appropriate personal protective equipment. Filling / patching primed iron surfaces: The acrylic putty KRAFT SPACHTEL is recommended. On rusty metal surfaces: First, remove any loose rust or paint with a wire brush, clean and apply 2-3 coats of KRAFT METAL 3 in 1 WROUGHT. On galvanised, zinc, aluminium, bronze, chrome or copper surfaces: fine sanding of patina, 1 coat of KRAFT RUST BLOCKER AQUA, and after 12 hours 2 coats of KRAFT METAL 3 in 1 WROUGHT To ensure maximum rust protection in coastal or northern areas, it is recommended to apply 2 coats of KRAFT RUST BLOCKER AQUA first. Paint Application Instructions Tools: paintbrush or roller (Ripolin), air or airless spray gun Cleaning: Immediately after use, clean tools and any paint residues with KRAFT Brush Thinner. Thinning: Paintbrush or roller: up to 9% by volume with KRAFT Brush Thinner Air spray gun: up to 9% by volume with Airless spray gun: up to 5% by volume with Dry to touch: 1-2 hours Dry to recoat, minimum: 12 hours Stir well before use and during application. Do not apply at temperatures below 5ÆC and above 35ÆC as well as at relative humidity levels above 65%. Pack Size Available in Index colours in 0.75L and 2.5L containers Instructions for Safe Use Flammable. Keep out of the reach of children. Use only in a well ventilated area. Do not inhale spray mist. Avoid contact with skin and eyes. Prolonged exposure may cause skin dryness or cracking. In case of contact with skin, wash off immediately with soap and water or with a suitable skin cleaner. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. In case of ingestion, seek medical advice immediately and show container or label. Toxic to aquatic organisms. It may cause long-term adverse effects in the aquatic environment. Do not empty remaining contents into drains or other water sources. Disposal of materials must be carried out responsibly and in accordance with applicable legislation. For more information, please refer to the Material Safety Data Sheet for this product. It contains ethyl methyl ketoxime and 2- ethylhexanoic cobalt. It may cause an allergic reaction. Poison Centre Tel.: 210-7793777 Storage Store product at temperatures between 5ÆC and 35ÆC and at a humidity rate < 50%. Keep cans hermetically closed. Special one-component coatings (SB) (A/i) Phase I limit value: 600 g/l Phase II limit value: 500 g/l Maximum content of VOC of the product in a ready-to-use condition: 499 g/l Technical Characteristics Specific Gravity (Kg/l) (±0.02) Viscosity (cp) Solids by Volume (%) Theoretical Coverage (m 2 /l) Minimum Dry Film Thickness required (Ìm) Flash Point Shelf Life Silver 1,00 Gold 1,00 Copper 1,01 Cypress Green 1,03 Aegean Blue 1,01 Ionian Blue 1,00 Claret 1,03 Grey 1,00 Carbon Black 1,00 Almond Green 1,00 1.000-2.300 47,5 ± 2 {ISO 3251} 4-5* (2 coats) {ISO 6504} 110 28ÆC {DIN 53213} at least 1 year * depending on painting conditions and application method