IntesisBox IS-IR-KNX-1i v1.0. User's Manual Issue Date: 06/2017 r1.0 eng

IntesisBx IS-IR-KNX-1i v1.0 User's Manual Issue Date: 06/2017 r1.0 eng

IntesisBx KNX IR Universal AC Intesis Sftware S.L.U. 2017 All Rights Reserved. Infrmatin in this dcument is subject t change withut ntice. The sftware described in this dcument is furnished under a license agreement r nndisclsure agreement. The sftware may be used nly in accrdance with the terms f thse agreements. N part f this publicatin may be reprduced, stred in a retrieval system r transmitted in any frm r any means electrnic r mechanical, including phtcpying and recrding fr any purpse ther than the purchaser s persnal use withut the written permissin f Intesis Sftware S.L.U. Intesis Sftware S.L.U. Milà I Fntanals, 1 bis 08700 Igualada Spain TRADEMARKS All trademarks and tradenames used in this dcument are acknwledged t be the cpyright f their respective hlders. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 2 / 48

IntesisBx KNX IR Universal AC Gateway fr integratin f IR air cnditiners int KNX TP-1 (EIB) cntrl systems. Cmpatible with AC units, f mst AC brands, prvided with an IR receiver. Applicatin s Prgram Versin: 1.0 Order Cde: IS-IR-KNX-1i Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 3 / 48

IntesisBx KNX IR Universal AC Table f Cntents 1 Presentatin... 6 2 Quick setup... 7 3 Device Installatin... 8 Lcatin selectin... 8 Cnnectin t IR and lcatin... 9 Cnnectin t KNX... 11 Binary Input cnnectin... 12 4 Cnfiguratin and setup... 14 5 ETS Parameters and Cnfiguratin... 15 General cnfiguratin... 16 5.1.1 AC brand... 16 5.1.2 Mdel... 16 5.1.3 Delay befre sending initial Read egrams... 16 5.1.4 Scene t execute n bus recvery / startup... 17 5.1.5 Enable lck cntrl bjects... 17 5.1.6 Enable func Operatin time bjects... 17 5.1.7 RGB LED mde... 18 AC supprted features... 18 Mde... 19 5.3.1 Enable use f bit-type Mde bjects (fr cntrl)... 19 5.3.2 Enable use f bit-type Mde bjects (fr status)... 19 5.3.3 Enable use f + / - bject fr Mde... 20 5.3.4 Enable use f Text bject fr Mde... 20 Fan Speed... 21 5.4.1 DPT bject type fr fan speed... 21 5.4.2 Enable use f bit-type Fan Speed bjects (fr Cntrl)... 22 5.4.3 Enable use f bit-type Fan Speed bjects (fr Status)... 22 5.4.4 Enable use f +/- bject fr Fan Speed... 23 5.4.5 Enable use f Text bject fr Fan Speed... 23 Up-Dwn vanes cnfiguratin dialg... 24 5.5.1 DPT bject type fr Vane Up-Dwn... 24 5.5.2 Enable use f bit-type Vane U-D bjects (fr Cntrl)... 25 5.5.3 Enable use f bit-type Vane U-D bjects (fr Status)... 25 5.5.4 Enable use f +/- bj fr Vane Up-Dwn... 26 5.5.5 Enable use f Text bject fr Vane U-D... 26 Left-Right vanes cnfiguratin dialg... 27 5.6.1 DPT bject type fr Vane Left-Right... 27 5.6.2 Enable use f bit-type Vane L-R bjects (fr Cntrl)... 28 5.6.3 Enable use f bit-type Vane U-D bjects (fr Status)... 28 5.6.4 Enable use f +/- bj fr Vane Left-Right... 29 5.6.5 Enable use f Text bject fr Vane U-D... 29 Temperature cnfiguratin dialg... 30 5.7.1 Set Pint - Enable use f +/- bj fr Setp Temp... 30 5.7.2 Set Pint - Enable limits n Cntrl_ Setpint bj... 31 5.7.3 Set Pint - Peridic sending time... 31 5.7.4 Ambient - Transmissin f Status_ AC Ret Temp... 31 5.7.5 Ambient - Peridic sending time... 31 Scene Cnfiguratin dialg... 32 5.8.1 Enable use f scenes... 32 5.8.2 Scenes can be saved frm KNX... 32 5.8.3 Enable use f bit-field bjects fr save... 33 5.8.4 Enable use f bit-field bjects fr execute... 33 5.8.5 Scene x preset... 34 Enable use f Open Windw... 35 Enable use f Occupancy functin... 36 Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 4 / 48

IntesisBx KNX IR Universal AC Binary Input x cnfiguratin dialgs... 38 5.11.1 Enable use f Input x... 38 5.11.2 Cntact type... 39 5.11.3 Debunce time... 39 5.11.4 Disabling functin... 39 5.11.5 Functin... 39 6 Electrical and Mechanical features... 40 7 List f cmpatible AC indr units.... 41 8 Appendix A Cmmunicatin Objects Table... 42 Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 5 / 48

IntesisBx KNX IR Universal AC 1 Presentatin IntesisBx IS-IR-KNX-1i allws mnitring and cntrl f Air Cnditiners frm KNX installatins. Cmpatible with mst AC units with an IR receiver. Great flexibility f integratin int yur KNX prjects. Cnfiguratin is made directly frm ETS, the database f the device cmes with a cmplete set f cmmunicatin bjects allwing, frm a simple and quick integratin using the basic bjects, allwing a simple and quick integratin. Main features: Reduced dimensins and quick installatin. Includes a USB cnnectr fr fast prgramming dwnlad. Multiple bjects fr cntrl and status (bit, byte, characters ) with KNX standard datapint types. Status bjects fr every cntrl available. Special Mdes available (Pwer, Ecnmy, Additinal Heating and Additinal Cling). Timeut fr Open Windw and Occupancy. Sleep functin als available. Cntrl f the AC unit based in the ambient temperature read by the wn AC unit, r in the ambient temperature read by any KNX thermstat. Ttal Cntrl and Mnitring f the AC unit frm KNX, including mnitring f AC unit s state f internal variables, running hurs cunter (fr filter maintenance cntrl), and errr indicatin and errr cde. AC unit can be cntrlled simultaneusly by the remte cntrller f the AC unit and by KNX. Up t 5 scenes can be saved and executed frm KNX, fixing the desired cmbinatin f Operatin Mde, Set Temperature, Fan Speed, Vane Psitin and Remte Cntrller Lck in any mment by using a simple switching. Tw binary inputs fr ptential-free cntacts prvide the pssibility t integrate many types f external devices fr windw status cntrl (windw cntacts) and ccupancy (presence sensr Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 6 / 48

IntesisBx KNX IR Universal AC 2 Quick setup Figure 2.1 IS-IR-KNX-1i integratin example 1. Check the interface lcatin that best fits the installatin (sectin 3.1) 2. Cnnect the interface t the KNX bus. 3. Dwnlad the ETS database fr this prduct, imprt it and add it t the current ETS prject. 4. Access the parameter sectin f the IntesisBx device. Ntice that parameters fr this interface are cnfigured thrugh a specific plugin (sectin 5). 5. Select the cmmunicatin bjects t be used and ther parameters. This step can be mitted if wrking with the default bjects and parameters. 6. Save the cnfiguratin file and dwnlad the applicatin prgram. 7. Clse the plugin and apply changes when asked. 8. Link the grup address frm the cmmunicatin bject f the KNX device with the cmmunicatin bject inside the IntesisBx interface. 9. Dwnlad the ETS parameters as with any ther standard KNX device. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 7 / 48

IntesisBx KNX IR Universal AC 3 Device Installatin Lcatin selectin Determining that the IntesisBx device will be wrking as expected in the installatin lcatin is an imprtant stage. In rder t determine the best lcatin fr yur IntesisBx device, use the Wireless Cntrller (the ne f yur AC unit). When selecting the installatin lcatin, please keep in mind that the IntesisBx device has 2 IR emitters and 1 IR receiver. The 2 emitters increase the installatin pssibilities allwing many different suitable psitins fr the device lcatin. On the ther hand, the receiver ffers the pssibility t get the feedback frm the IR wireless remte cntrller s the KNX status bjects can be updated with that feedback. IR transmissin area IR receptin area Figure 3.1 IR emitters and IR receiver lcatin Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 8 / 48

IntesisBx KNX IR Universal AC Cnnectin t IR and lcatin There is n special requirement t match the IR receiver and the IntesisBx IS-IR-KNX-1i interface. Simply select yur mdel frm the list present in the plugin. If yur AC unit is nt present, please check the cmpatibility list as in sectin 7. Yu can find mre infrmatin abut the IR cnfiguratin in sectin 5.! IMPORTANT: Keep in mind that sme furniture and materials (carpets, curtains, glass, metal ) may affect n the IR cmmunicatin.! NOTE: The IntesisBx device has 2 IR emitters pinting at 2 different lcatins. Cnsidering this and IR reflectins, valid lcatins fr the IntesisBx device may be many and very different depending n each installatin. Check sectin 3.1 fr mre infrmatin. IntesisBx IS-IR-KNX-1i can be installed in many different lcatins. A) Side-by-side with the AC unit B) In frnt f the AC unit C) Under the AC unit D) Desktp psitin D Figure 3.2 IR emitters and IR receiver lcatin Case A: Installed side-by-side with the AC unit. In that case, the signal will travel frm the IntesisBx device t the AC unit tacking advantage f the rebunds n the flr r ther furniture present in the rm. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 9 / 48

IntesisBx KNX IR Universal AC Case B: Installed in frnt f the AC unit. In that case, the signal will travel frm the IntesisBx device directly t the AC unit. Case C: Installed belw the AC unit. In that case, the signal will travel frm the IntesisBx device t the AC unit tacking advantage f the rebunds n the wall in frnt f it r ther furniture present in the rm. Case D: If yu want t place the device n yur desktp r any ther hrizntal surface, please cnsider the sketch belw. In this case, the signal will travel directly frm the IntesisBx device t the AC unit. Figure 3.3 Desktp munted psitin In rder nt t prduce marks r scratches n the surface and als t imprve the device stability, yu can use the rubber dumpers included in the package. Please, check Figure 3.4. Figure 3.4 Rubber dumpers lcatin Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 10 / 48

IntesisBx KNX IR Universal AC Cnnectin t KNX IntesisBx device needs t be cnnected directly thrugh a KNX TP-1 bus. T get access t the KNX cnnectr, remve the screw as seen in Figure 3.5. Setscrew Figure 3.5 Tp lid release and KNX cnnectin Discnnect pwer f the KNX bus. Cnnect the IS-IR-KNX-1i t the KNX TP-1 (EIB) bus using the KNX standard cnnectr (red/grey) f the IS-IR-KNX-1i, respect plarity. Recnnect pwer f the KNX bus, and mains pwer f the AC unit. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 11 / 48

IntesisBx KNX IR Universal AC Binary Input cnnectin IntesisBx IS-IR-KNX.1i interface is equipped with a Binary Input frm factry. T use the built-in binary input in all the IR WIFI Cntrllers, a standard 3,5mm stere jack cnnectr is required. Cnnectins will be as in the image belw. BINARY INPUT CONNECTOR OPTION 1: PRESENCE DETECTOR KNX INPUT CONNECTOR STEREO JACK (3,5 mm) OPTION 2: WINDOW CONTACT RIGHT CHANNEL COMMON RIGHT COMMON LEFT (nt used) Figure 3.6 Binary Input cnnectin IMPORTANT NOTE: Please, nte that yu can nly cnnect a presence sensr r a windw cntact simultaneusly. Bth sensrs cannt wrk tgether at same time. Befre prceeding, please check the technical specificatin f the binary input belw: Ptential free binary input Signal cable length: 5m unshielded, may be extended up t 20m with twisted Cmpliant with the fllwing standards: IEC61000-4-2: level 4 15kV (air discharge) - 8kV (cntact discharge) MIL STD 883E-Methd 3015-7: class 3B Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 12 / 48

IntesisBx KNX IR Universal AC Once yu are sure yur installatin is cmpliant with the specificatins, please check the presence sensr r windw cntact yu wuld like t use. Basically, sensrs nly need t be equipped with a ptential free external cntact. N matter if the cntact is NO (Nrmally Open) r NC (Nrmally clsed) as yu will be able t cnfigure the cntact type (NO r NC) f yur sensr in the settings f the Binary Input functin (G t Settings menu in the IntesisBx WEB Site). IMPORTANT NOTE: Please, nte that IS-IR-KNX-1i interface will nly react if the cntact f yur sensr is pened r clsed. In the case f the presence sensr, the installer needs t decide the specific settings f the presence sensr t be applied. IntesisBx will be nt respnsible f the incrrect settings r incrrect installatins. Recmmendatin: In sme presence sensrs r windw cntacts it is pssible t setup a delay time t the external cntact. As yu will see in this manual, IntesisBx Settings allw the user t setup a timer befre starting with the cnfigured actins. Anyway, we recmmend t setup a certain delay time in yur presence sensr r windw cntact t prevent cntinuus cntact changes in a very shrt perid f time. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 13 / 48

IntesisBx KNX IR Universal AC 4 Cnfiguratin and setup This is a fully cmpatible KNX device which must be cnfigured and setup using standard KNX tl ETS. Befre starting with the cnfiguratin, please make sure that the binary inputs (if used) and the USB cable are prperly cnnected t the interface. Make sure as well, that the interface is cnnected t the KNX bus t allw the prper dwnlad f the KNX prgramming. In rder t prceed with the cnfiguratin and set up, it is recmmended t fllw instructins next: 1. Dwnlad and install the latest versin f the ETS data base (sectin 5). 2. Open the prduct s plugin and make sure that the catalg is in its last available versin (sectin 5). 3. Select yur AC brand and mdel (sectin 5.1). 4. Dwnlad the infrared cnfiguratin t the IntesisBx pushing n the Dwnlad IR parameters. NOTE: Check the current cnnectin t the IntesisBx. Ntice that in rder t send the Infrared cnfiguratin, yu can use the standard KNX cnnectin (the same used t prgram the device) r a USB cnnectin. USB cnnectin is faster than KNX cnnectin. Ntice that this is nly available fr the infrared cnfiguratin settings. 5. Prceed with the rest f AC unit settings and ther parameters. 6. Prceed with the KNX prgramming. 7. Dwnlad the prgramming t the interface as any ther KNX device. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 14 / 48

IntesisBx KNX IR Universal AC 5 ETS Parameters and Cnfiguratin The IntesisBx IS-IR-KNX-1i interface is cnfigured thrugh ETS. General KNX parameters, such as the physical address, grup addresses r DPTs can be cnfigured as usual using the ETS interface. Fr the specific AC unit cnfiguratin and IR cmmunicatin, the use f the specific plugin included in the ETS database is required. ETS database fr this device can be dwnladed frm: https://www.intesisbx.cm/intesis/prduct/media/is-ir-knx-1i_ets_database.zip Please cnsult the README.txt file, lcated inside the dwnladed zip file, t find instructins n hw t install the database. Once the database is imprted, the plugin can be accessed when editing parameters. T get access t parameters editin, click n the Parameter tab, lcated in the prject screen, and then press the specific parameter dialg. Figure 5.1 ETS Prject managing and plugin screen Remember that befre start using the IntesisBx interface alng with the AC unit, yu need t set up at least the brand and type f yu AC unit. Check sectin 5.1 fr mre infrmatin abut it. IMPORTANT: Please, update the Catalgue befre prceeding with the device cnfiguratin and prgramming. The laptp where ETS is running shall have Internet cnnectin t update the catalgue. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 15 / 48

IntesisBx KNX IR Universal AC General cnfiguratin Inside this parameter s dialg it is pssible t activate r change the parameters shwn belw: AC brand AC unit mdel Figure 5.2 General parameters 5.1.1 AC brand Use the drpdwn menu t select the AC brand f the AC unit yu want t cntrl. In case yur AC unit brand is nt present, please select the IS-IR-KNX-1i and cntact ur supprt department fr mre infrmatin abut the Mdel t select. 5.1.2 Mdel Use the drpdwn menu t select the AC brand f the AC unit yu want t cntrl. In case yur AC unit brand is nt present in the AC brand list, please select the IS-IR-KNX-1i and cntact ur supprt department fr mre infrmatin abut the Mdel t select. 5.1.3 Delay befre sending initial Read egrams This parameter sets the delay befre the interface will send READ egrams fr the grup addresses assciated n its Cntrl_ bjects n bus recvery r applicatin reset/start-up. All Cntrl_ bjects with bth Transmit (T) and Update (U) flags enabled will send READs and their values will be updated with the respnse when received. Valid values g frm 10 t 60 secnds. This is t give time enugh t ther KNX devices n the bus t start-up befre sending the READs. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 16 / 48

IntesisBx KNX IR Universal AC 5.1.4 Scene t execute n bus recvery / startup This parameter executes a selected scene n bus recvery r startup, nly if the selected scene has an enabled preset r values previusly saved frm KNX bus (see Scene Cnfiguratin dialg). Yu can select any f the 5 available scenes. 5.1.5 Enable lck cntrl bjects This parameter shws/hide the Cntrl_ Lck Cntrl Obj cmmunicatin bject which, depending n the sent value, lcks r unlcks ALL the Cntrl_ cmmunicatin bjects except itself. When a 1 value is sent t this cmmunicatin bject, the remte cntrller is lcked. T be unlcked a 0 value must be sent. The gateway remembers the last value received even if a KNX bus reset/failure happens. Figure 5.3 Cmmunicatin bject detail Imprtant: If an initial scene is enabled and it has as Value fr Remte Lck (unchanged) r unlcked, this wuld unlck the remte cntrller because the initial scene has pririty ver the Cntrl_ Lck Remte Cntrl cmmunicatin bject. 5.1.6 Enable func Operatin time bjects This parameter shws/hides the Status_ Operating Hur Cunter and Status_ Operating Secnd Cunter cmmunicatin bject which cunts the number f perating hurs fr the IS-IR-KNX-1i. Figure 5.4 Cmmunicatin bject detail If set t n the bject will nt be shwn. If set t yes the Status_ Operatin Hur Cunter bject will appear. This bject can be read and sends its status every time an hur is cunted. The gateway keeps that cunt in memry and the status is sent als after a KNX bus reset/failure. Althugh this bject is marked as a Status_ bject it als can be written t update the cunter when needed. T reset the cunter shuld be written a 0 value. Imprtant: This bject cmes by default withut the write (W) flag activated. If is necessary t write n it, this flag must be activated. Imprtant: This bject will als return its status, every time a value is written, nly if it s different frm the existing ne. Imprtant: If the stred value is 0 hurs, the gateway will nt send the status t KNX. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 17 / 48

IntesisBx KNX IR Universal AC 5.1.7 RGB LED mde This parameter determines the wrking mde f the interface LED. If set t Always ff the LED will always be ff. If set t Always n the LED will always be n. If set t Only n changes the LED will always change when there is a change f value in any f the active cmmunicatin bjects. AC supprted features Select the AC features f yur AC unit t match bth: the AC unit features with the enabled cmmunicatin bjects and parameters. Please, select these parameters carefully, therwise nt expected behavir may ccur. Figure 5.5 AC supprted features Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 18 / 48

IntesisBx KNX IR Universal AC Mde All the parameters in this sectin are related with the different mde prperties and cmmunicatin bjects. The byte-type cmmunicatin bject fr Mde wrks with the DTP_20.105. Aut mde will be enabled with a 0 value, Heat mde with a 1 value, Cl mde with a 3 value, Fan mde with a 9 value and Dry mde with a 14 value. Figure 5.6 AC mde additinal cmmunicatin bjects 5.3.1 Enable use f bit-type Mde bjects (fr cntrl) This parameter shws/hides the bit-type Cntrl_ Mde bjects. Figure 5.7 Cmmunicatin bject detail If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Mde bjects fr Aut, Heat, Cl, Fan and Dry will appear. T activate a mde by using these bjects a 1 value has t be sent. 5.3.2 Enable use f bit-type Mde bjects (fr status) This parameter shws/hides the bit-type Status_ Mde bjects. Figure 5.8 Cmmunicatin bject detail Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 19 / 48

IntesisBx KNX IR Universal AC If set t n the bjects will nt be shwn. If set t yes the Status_ Mde bjects fr Aut, Heat, Cl, Fan and Dry will appear. When enabled, a mde will return a 1 thrugh its bit-type bject. 5.3.3 Enable use f + / - bject fr Mde This parameter shws/hides the Cntrl_ Mde +/- cmmunicatin bject which lets change the indr unit mde by using tw different datapint types. If set t n the bject will nt be shwn. If set t yes the Cntrl_ Mde +/- bject and a new parameter will appear. DPT type fr +/- Mde Object This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1- Increase [DPT_1.007] fr the Cntrl_ Mde +/- bject. The sequence fllwed when using this bject is shwn belw: AUTO HEAT COOL FAN DRY Up / Increase Dwn / Decrease 5.3.4 Enable use f Text bject fr Mde This parameter shws/hides the Status_ Mde Text cmmunicatin bject. If set t n the bject will nt be shwn. If set t yes the Status_ Mde Text bject will appear. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 20 / 48

IntesisBx KNX IR Universal AC Fan Speed All the parameters in this sectin are related with the Fan Speed prperties and cmmunicatin bjects. Figure 5.9 Fan Speed parameters 5.4.1 DPT bject type fr fan speed With this parameter is pssible t change de DPT fr the Cntrl_ Fan Speed and Status_ Fan Speed bytetype cmmunicatin bjects. Datapints Scaling (DPT_5.001) and Enumerated (DPT_5.010) can be selected. When Enumerated [DPT 5.010] is selected, Cntrl_ Fan Speed and Status_ Fan Speed cmmunicatin bjects fr this DPT will appear. Als, depending n the number f fan speeds selected, these bjects will be different. The first fan speed will be selected if a 1 is sent t the Cntrl_ bject. The secnd fan speed will be selected sending a 2 and s n. The Status_ bject will always return the value fr the fan speed selected. Imprtant: In bth cases if a 0 value is sent t the Cntrl_ bject, the minimum fan speed will be selected. If a value bigger than 2 (in case f 2 speeds) r bigger than 3 (in case f 3 fan speeds) is sent t the Cntrl_ bject, then the maximum fan speed will be selected. When Scaling [DPT 5.001] is selected, Cntrl_ Fan Speed and Status_ Fan Speed cmmunicatin bjects fr this DPT will appear. Als, depending n the number f fan speeds selected, these bjects will be different. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 21 / 48

IntesisBx KNX IR Universal AC The frmula used t calculate the value t be set in the Cntrl bject is 100*(n+0,5)/N %, where n is the current fan speed and N the maximum number f fan speeds. On the ther hand, the frmula t calculate the status t be read accrding t the current value is 100*n/N, where n is the current fan speed and N the maximum number f fan speeds. Check this example with 3 fan speeds: When a value between 0% and 49% is sent t the Cntrl_ bject the first fan speed will be selected. When a value between 50% and 83% is sent t the Cntrl_ bject, the secnd speed will be selected. When a value between 84% and 100% is sent t the Cntrl_ bject, the third speed will be selected. The Status_ bject will return a 33% when the first speed is selected, a 67% fr the secnd ne and a 100% fr the third ne. Cntrl_ bject Cntrl_ Cntrl_ Fan Speed 1 Fan Speed 2 Fan Speed 3 0% 33% 50% 67% 83% 100% Status_ Status_ Status_ 5.4.2 Enable use f bit-type Fan Speed bjects (fr Cntrl) This parameter shws/hides the bit-type Cntrl_ Fan Speed bjects. If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Fan Speed bjects fr Speed 1, Speed 2 and Speed 3 (if available) will appear. T activate a Fan Speed by using these bjects a 1 value has t be sent. 5.4.3 Enable use f bit-type Fan Speed bjects (fr Status) This parameter shws/hides the bit-type Status_ Fan Speed bjects. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 22 / 48

IntesisBx KNX IR Universal AC If set t n the bjects will nt be shwn. If set t yes the Status_ Fan Speed bjects fr Speed 1, Speed 2 and Speed 3 (if available) will appear. When a Fan Speed is enabled, a 1 value is returned thrugh its bit-type bject. 5.4.4 Enable use f +/- bject fr Fan Speed This parameter shws/hides the Cntrl_ Fan Speed +/- cmmunicatin bject which lets yu increase/decrease the indr unit fan speed by using tw different datapint types. If set t n the bject will nt be shwn. If set t yes the Cntrl_ Fan Speed +/- bject. DPT type fr +/- Fan Speed Object This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1- Increase [DPT_1.007] fr the Cntrl_ Fan Speed +/- bject. Rll-ver Speed at upper/lwer limit This parameter lets chse if rll-ver will be enabled ( yes ) r disabled ( n ) fr the Cntrl_ Fan Speed +/- bject. Only if Rll-ver is enabled Fan Speed 1 Fan Speed 2 Fan Speed 3 Only if Rll-ver is enabled 5.4.5 Enable use f Text bject fr Fan Speed Up / Increase Dwn / Decrease This parameter shws/hides the Status_ Fan Speed Text cmmunicatin bject. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 23 / 48

IntesisBx KNX IR Universal AC If set t n the bject will nt be shwn. If set t yes the Status_ Fan Speed Text bject will appear. Up-Dwn vanes cnfiguratin dialg All the parameters in this sectin are related with the Vane Up-Dwn prperties and cmmunicatin bjects. 5.5.1 DPT bject type fr Vane Up-Dwn With this parameter is pssible t change de DPT fr the Cntrl_ Vane Up-Dwn and Status_ Vane Up-Dwn byte-type cmmunicatin bjects. Datapints Scaling (DPT_5.001) and Enumerated (DPT_5.010) can be selected. When Enumerated [DPT 5.010] is selected, Cntrl_ Vane Up-Dwn and Status_ Vane Up-Dwn cmmunicatin bjects fr this DPT will appear. T chse a vane psitin, values frm 1 t N can be sent t the Cntrl_ bject. Each value will crrespnd t the psitin (i.e. Value 3 = Psitin 3). The Status_ bject will always return the value fr the vane psitin selected. Imprtant: If a 0 value is sent t the Cntrl_ bject, the Psitin 1 will be selected. If a value bigger than N is sent t the Cntrl_ bject, then the Psitin N will be selected. When Scaling [DPT 5.001] is selected, Cntrl_ Vane Up-Dwn and Status_ Vane Up-Dwn cmmunicatin bjects fr this DPT will appear. The frmula used t calculate the value t be set in the Cntrl bject is 100*(n+0,5)/N %, where n is the current fan speed and N the maximum number f fan speeds. On the ther hand, the frmula t calculate the status t be read accrding t the current value is 100*n/N, where n is the current fan speed and N the maximum number f fan speeds. Check the example with 5 psitins: When a value between 0% and 29% is sent t the Cntrl_ bject the first vane psitin will be selected. When a value between 30% and 49% is sent t the Cntrl_ bject, the secnd vane psitin will be selected. When a value between 50% and 69% is sent t the Cntrl_ bject, the third vane psitin will be selected. When a value between 70% and 89% is sent t the Cntrl_ bject, the furth vane psitin will be selected. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 24 / 48

IntesisBx KNX IR Universal AC When a value between 90% and 100% is sent t the Cntrl_ bject, the fifth vane psitin will be selected. The Status_ bject will return a 20% fr the first vane psitin, a 40% fr the secnd ne, a 60% fr the third ne, an 80% fr the furth ne and a 100% fr the fifth and last ne. Cntrl_ bject Cntrl_ Cntrl_ Ps. 1 Ps. 2 Ps. 3 Cntrl_ 0% 20% 30% 40% 50% 60% 70% 80% 90% Cntrl_ Ps. 4 Ps. 5 100% Status_ Status_ Status_ Status_ Status_ 5.5.2 Enable use f bit-type Vane U-D bjects (fr Cntrl) This parameter shws/hides the bit-type Cntrl_ Vane Up-Dwn bjects. If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Vane Up-Dwn bjects fr each Psitin (1 t 5) will appear. T activate a Vane Psitin by using these bjects, a 1 value has t be sent. 5.5.3 Enable use f bit-type Vane U-D bjects (fr Status) This parameter shws/hides the bit-type Status_ Vane Up-Dwn bjects. If set t n the bjects will nt be shwn. If set t yes the Status_ Vane Up-Dwn bjects fr each Psitin (1 t N) will appear. When a Vane Psitin is enabled, a 1 value is returned thrugh its bit-type bject. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 25 / 48

IntesisBx KNX IR Universal AC 5.5.4 Enable use f +/- bj fr Vane Up-Dwn This parameter shws/hides the Cntrl_ Vane Up-Dwn +/- cmmunicatin bject which lets yu change the indr unit vane psitin by using tw different datapint types. If set t n the bject will nt be shwn. If set t yes the Cntrl_ Vane Up-Dwn +/- bject. DPT type fr +/- Vane Up-Dwn bj This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1- Increase [DPT_1.007] fr the Cntrl_ Vane Up-Dwn +/- bject. Rllver Vane at upper/lwer limit This parameter lets chse if rll-ver will be enabled ( yes ) r disabled ( n ) fr the Vane Up-Dwn +/- bject. Only if Rll-ver is enabled Ps. 1 Ps. 2 Ps. 3 Ps. 4 Ps. 5 SWING Only if Rll-ver is enabled Up / Increase Dwn / Decrease 5.5.5 Enable use f Text bject fr Vane U-D This parameter shws/hides the Status_ Vane Up-Dwn Text cmmunicatin bject. If set t n the bject will nt be shwn. If set t yes the Status_ Vane Up-Dwn Text bject will appear. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 26 / 48

IntesisBx KNX IR Universal AC Left-Right vanes cnfiguratin dialg All the parameters in this sectin are related with the Vane Up-Dwn prperties and cmmunicatin bjects. 5.6.1 DPT bject type fr Vane Left-Right With this parameter is pssible t change de DPT fr the Cntrl_ Vane Left-Right and Status_ Vane Left-Right byte-type cmmunicatin bjects. Datapints Scaling (DPT_5.001) and Enumerated (DPT_5.010) can be selected. When Enumerated [DPT 5.010] is selected, Cntrl_ Vane Left-Right and Status_ Vane Left-Right cmmunicatin bjects fr this DPT will appear. T chse a vane psitin, values frm 1 t N can be sent t the Cntrl_ bject. Each value will crrespnd t the psitin (i.e. Value 3 = Psitin 3). The Status_ bject will always return the value fr the vane psitin selected. Imprtant: If a 0 value is sent t the Cntrl_ bject, the Psitin 1 will be selected. If a value bigger than N is sent t the Cntrl_ bject, then the Psitin N will be selected. When Scaling [DPT 5.001] is selected, Cntrl_ Vane Up-Dwn and Status_ Vane Up-Dwn cmmunicatin bjects fr this DPT will appear. The frmula used t calculate the value t be set in the Cntrl bject is 100*(n+0,5)/N %, where n is the current fan speed and N the maximum number f fan speeds. On the ther hand, the frmula t calculate the status t be read accrding t the current value is 100*n/N, where n is the current fan speed and N the maximum number f fan speeds. Check the example with 5 psitins: When a value between 0% and 29% is sent t the Cntrl_ bject the first vane psitin will be selected. When a value between 30% and 49% is sent t the Cntrl_ bject, the secnd vane psitin will be selected. When a value between 50% and 69% is sent t the Cntrl_ bject, the third vane psitin will be selected. When a value between 70% and 89% is sent t the Cntrl_ bject, the furth vane psitin will be selected. When a value between 90% and 100% is sent t the Cntrl_ bject, the fifth vane psitin will be selected. The Status_ bject will return a 20% fr the first vane psitin, a 40% fr the secnd ne, a 60% fr the third ne, an 80% fr the furth ne and a 100% fr the fifth and last ne. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 27 / 48

IntesisBx KNX IR Universal AC Cntrl_ bject Cntrl_ Cntrl_ Ps. 1 Ps. 2 Ps. 3 Cntrl_ 0% 20% 30% 40% 50% 60% 70% 80% 90% Cntrl_ Ps. 4 Ps. 5 100% Status_ Status_ Status_ Status_ Status_ 5.6.2 Enable use f bit-type Vane L-R bjects (fr Cntrl) This parameter shws/hides the bit-type Cntrl_ Vane Left-Right bjects. If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Vane Up-Dwn bjects fr each Psitin (1 t N) will appear. T activate a Vane Psitin by using these bjects, a 1 value has t be sent. 5.6.3 Enable use f bit-type Vane U-D bjects (fr Status) This parameter shws/hides the bit-type Status_ Vane Up-Dwn bjects. If set t n the bjects will nt be shwn. If set t yes the Status_ Vane Up-Dwn bjects fr each Psitin (1 t N) will appear. When a Vane Psitin is enabled, a 1 value is returned thrugh its bit-type bject. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 28 / 48

IntesisBx KNX IR Universal AC 5.6.4 Enable use f +/- bj fr Vane Left-Right This parameter shws/hides the Cntrl_ Vane Left-Right +/- cmmunicatin bject which lets yu change the indr unit vane psitin by using tw different datapint types. If set t n the bject will nt be shwn. If set t yes the Cntrl_ Vane Left-Right +/- bject. DPT type fr +/- Vane Left-Right bj This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1- Increase [DPT_1.007] fr the Cntrl_ Vane Left-Right +/- bject. Rllver Vane at upper/lwer limit This parameter lets chse if rll-ver will be enabled ( yes ) r disabled ( n ) fr the Vane Up-Dwn +/- bject. Only if Rll-ver is enabled Ps. 1 Ps. 2 Ps. 3 Ps. 4 Ps. 5 SWING Only if Rll-ver is enabled Up / Increase Dwn / Decrease 5.6.5 Enable use f Text bject fr Vane U-D This parameter shws/hides the Status_ Vane Up-Dwn Text cmmunicatin bject. If set t n the bject will nt be shwn. If set t yes the Status_ Vane Up-Dwn Text bject will appear. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 29 / 48

IntesisBx KNX IR Universal AC Temperature cnfiguratin dialg All the parameters in this sectin are related with the Temperature prperties and cmmunicatin bjects. Figure 5.10 Tempeature settings 5.7.1 Set Pint - Enable use f +/- bj fr Setp Temp This parameter shws/hides the Cntrl_ Setpint Temp +/- cmmunicatin bject which lets yu change the indr unit setpint temperature by using tw different datapint types. If set t n the bject will nt be shwn. If set t yes the Cntrl_ Setpint Temp +/- bject. DPT type fr +/- Setp Temp bject This parameter lets chse between the datapints 0-Up / 1-Dwn [DPT_1.008] and 0-Decrease / 1- Increase [DPT_1.007] fr the Cntrl_ Setpint Temp +/- bject. (Lwer limit) 16ºC 17ºC 31ºC 32ºC (Upper limit) Up / Increase Dwn / Decrease Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 30 / 48

IntesisBx KNX IR Universal AC 5.7.2 Set Pint - Enable limits n Cntrl_ Setpint bj This parameter enables t define temperature limits fr the Cntrl_ Setpint Temperature bject. If set t n the setpint temperature limits fr the Cntrl_ Setpint Temperature bject will be the default: 16ºC fr the lwer limit and 32ºC fr the upper limit. If set t yes it is pssible t define temperature limits fr the Cntrl_ Setpint Temperature bject. Cntrl_ Set Temp Lwer limit (ºC) This parameter lets t define the lwer limit fr the setpint temperature. Cntrl_ Set Temp Upper limit (ºC) This parameter lets t define the upper limit fr the setpint temperature. Imprtant: If a setpint temperature abve the upper defined limit (r belw the lwer defined limit) is sent thrugh the Cntrl_ Setpint Temperature bject, it will be ALWAYS applied the limit defined. Imprtant: When limits are enabled, any setpint temperature sent t the AC (even thrugh scenes, special mdes, etc.) will be limited. 5.7.3 Set Pint - Peridic sending time This parameter lets yu change the interval f time (in secnds, frm 0 t 255) at the end f which the AC setpint temperature is sent t the KNX bus. Fr a 0 value, the AC setpint temperature will ONLY be sent n change. The AC setpint temperature is sent thrugh the cmmunicatin bject Status_ AC Setpint Temp. 5.7.4 Ambient - Transmissin f Status_ AC Ret Temp This parameter lets t yu chse if the AC return temperature will be sent nly cyclically, nly n change r cyclically and n change. The AC return temperature is sent thrugh the cmmunicatin bject Status_ AC Return Temp. 5.7.5 Ambient - Peridic sending time This parameter will nly be available fr the nly cylically and cyclically and n change ptins, and lets yu change the interval f time (in secnds, frm 1 t 255) at the end f which the AC return temperature is sent t the KNX bus. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 31 / 48

IntesisBx KNX IR Universal AC Scene Cnfiguratin dialg All the parameters in this sectin are related with the Scene prperties and cmmunicatin bjects. A scene cntains values f: On/Off, Mde, Fan speed, Vane psitin and Setpint Temperature. Figure 5.11 Scene cnfiguratin settings 5.8.1 Enable use f scenes This parameter shws/hides the scene cnfiguratin parameters and cmmunicatin bjects. If set t n the scene parameters and cmmunicatin bjects will nt be shwn. If set t yes the scene parameters and cmmunicatin bjects will be shwn. T execute a scene thrugh the byte-type bject, a value frm 0 t 4 has t be sent, crrepnding each ne t a different scene (i.e. 0 = Scene 1; 4 = Scene 5). 5.8.2 Scenes can be saved frm KNX This parameter shws/hides the Cntrl_ Save/Exec Scene and all the Cntrl_ Save Scene (if enabled) cmmunicatin bjects. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 32 / 48

IntesisBx KNX IR Universal AC If set t n the cmmunicatin bjects will nt be shwn. If set t yes the cmmunicatin bjects and a new parameter will appear. T stre a scene thrugh the byte-type bject, a value frm 128 t 132 has t be sent t the bject, crrepnding each ne t a different scene (i.e. 128 = Scene 1; 132 = Scene 5). Enable use f bit bjects fr string scenes (frm bus) If set t n the bjects will nt be shwn. If set t yes the Cntrl_ Stre Scene bjects fr string scenes will appear. T stre a scene by using these bjects, a 1 value has t be sent t the scene s bject we want t stre (i.e. t stre scene 4, a 1 has t be sent t the Cntrl_ Stre Scene 4 bject). 5.8.3 Enable use f bit-field bjects fr save This parameter shws/hides the Cntrl_ Execute Scene bit-type cmmunicatin bjects. If set t n the cmmunicatin bjects will nt be shwn. If set t yes the cmmunicatin bjects will appear. T execute a scene by using these bjects, a 1 value has t be sent t the scene s bject we want t execute (i.e. t execute scene 4, a 1 has t be sent t the Cntrl_ Execute Scene 4 bject). 5.8.4 Enable use f bit-field bjects fr execute This parameter shws/hides the Cntrl_ Execute Scene bit-type cmmunicatin bjects. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 33 / 48

IntesisBx KNX IR Universal AC If set t n the cmmunicatin bjects will nt be shwn. If set t yes the cmmunicatin bjects will appear. T execute a scene by using these bjects, a 1 value has t be sent t the scene s bject we want t execute (i.e. t execute scene 4, a 1 has t be sent t the Cntrl_ Execute Scene 4 bject). 5.8.5 Scene x preset This parameter lets yu define a preset fr a scene (the fllwing descriptin is valid fr all the scenes). If set t n the preset fr the scene x will be disabled. If set t yes the preset will be enabled. When a scene is executed the values cnfigured in the preset will be aplied. Imprtant: If a scene s preset is enabled, will nt be pssible t mdify (stre) the scene frm the KNX bus. Scene x / Value fr On-Off This parameter lets yu chse the pwer f the indr unit when the scene is executed. The fllwing ptins are available: ON, OFF r (unchanged). Scene x / Value fr Mde This parameter lets yu chse the mde f the indr unit when the scene is executed. The fllwing ptins are available: AUTO, HEAT, COOL, FAN, DRY, r (unchanged). Scene x / Value fr Fan Speed This parameter lets yu chse the fan speed f the indr unit when the scene is executed. The fllwing ptins are available: SPEED 1, SPEED 2 SPEED N, r (unchanged). Scene x / Value fr Vane Up-Dwn This parameter lets yu chse the vane psitin f the indr unit when the scene is executed. The fllwing ptins are available: POSITION 1, POSITION 2 POSITION N, SWIRL, SWING r (unchanged). Scene x / Value fr Vane Left-Right This parameter lets yu chse the vane psitin f the indr unit when the scene is executed. The fllwing ptins are available: POSITION 1, POSITION 2 POSITION N, SWIRL, SWING r (unchanged). Scene x / Value fr Setp Temp (ºC) This parameter lets yu chse the setpint temperature f the indr unit when the scene is executed. The fllwing ptins are available: frm 16ºC t 32ºC (bth included), r (unchanged). Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 34 / 48

IntesisBx KNX IR Universal AC Imprtant: If any preset value is cnfigured as (unchanged), the executin f this scene will nt change current status f this feature in the AC unit. Imprtant: When a scene is executed, Status_ Current Scene bject shws the number f this scene. Any change in previus items des Status_ Current Scene shw N Scene. Only changes n items marked as (unchanged) will nt disable current scene. Enable use f Open Windw This parameter shws/hides the Cntrl_ Windw Cntact Input cmmunicatin bject which lets yu Start/Stp a timeut t switch ff the indr unit. If set t n the bject will nt be shwn. If set t yes the Cntrl_ Windw Cntact Input bject will appear. If a 1 value is sent t this bject, and the indr unit is already turned n, the switch-ff timeut will begin. If a 0 value is sent t this bject, the switch-ff timeut will stp. Input Object This parameter lets yu chse between the datapints 0-Open / 1-Clsed Windw [DPT_1.009] and 0-Stp / 1-Start Timeut [DPT_1.010] fr the Cntrl_ Switch Off Timeut. Timeut (min) This parameter lets yu select hw much time (in minutes) t wait befre switching ff the indr unit. Relad last Value If set t n, nce the switch-ff timeut is stpped, any value will be reladed. If set t yes, nce the switch-ff timeut is stpped, the last On/Off value sent will be reladed. If a 1 value is sent t the Cntrl_ Windw Cntact Input bject after the timeut perid, the indr unit will turn n. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 35 / 48

IntesisBx KNX IR Universal AC If a 0 value is sent t the Cntrl_ Switch Off Timeut after the timeut perid, n actin will be perfrmed. Lck ON when Open If set t n, On/Off cmmands while the windw is pen will be accepted. If a 1 value is sent t the Cntrl_ Switch Off Timeut bject the switch-ff timeut perid will begin again. If a 0 value is sent t the Cntrl_ Switch Off Timeut bject, n actin will be perfrmed. If set t yes, On/Off cmmands, while the windw is pen, will be saved (but nt applied). These cmmands will be used in the next parameter if set t yes. Enable use f Occupancy functin This parameter shws/hides the Cntrl_ Occupancy Input cmmunicatin bject which lets yu apply different parameters t the indr unit depending n the presence/n presence in the rm. If set t n the bject will nt be shwn. If set t yes the Cntrl_ Occupancy bject and new parameters will appear. If a 1 value is sent t this bject (n rm ccupancy), the timeut will begin. If a 0 value is sent t this bject, the timeut will stp. Figure 4.33 Parameter detail Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 36 / 48

IntesisBx KNX IR Universal AC Timeut t apply actin (minutes) This parameter lets yu chse hw much time t wait (in minutes) befre executing the actin specified in the next parameter ( Actin after timeut elapsed ). Actin When Switch Off AC is selected, nce the timeut has elapsed, the indr unit will be turned ff. When Apply Preset Delta is selected, nce the timeut has elapsed, a delta temperature will be applied in rder t save energy (decreasing the setpint when in Heat mde, r increasing the setpint when in Cl mde). Als new parameters will appear. Temp delta decrease (HEAT) r increase (COOL) (ºC) Secnd Actin This parameter lets cnfigure the delta temperature (increase r decrease) that will be applied when the timeut has elapsed. Imprtant: When there is ccupancy again after the applicatin f a delta, the same delta will be applied inversely. (i.e. In a rm with AC in cl mde and 25ºC setpint temperature, a +2ºC delta is applied after the ccupancy timeut, setting the setpint at 27ºC because there is n ccupancy in the rm. If the setpint is raised t 29ºC during that perid, when the rm is ccupied again, a -2ºC delta will be applied and the final setpint temperature will then be 27ºC). If set t n nthing will be applied. If set t yes, a new timeut will be enabled and tw new parameters will appear. Timeut (2nd) This parameter lets yu chse hw much time t wait (in minutes) befre executing the actin specified in the next parameter ( Actin after timeut elapsed ). Actin (2nd) When Switch-Off is selected, nce the timeut has elapsed, the indr unit will turn ff. When Apply Preset Delta is selected, nce the timeut cnfigured is extinguished, a delta temperature will be applied (decreasing the setpint when in Heat mde, r increasing the setpint when in Cl mde). Als new parameters will appear. Temp delta decrease (HEAT) r increase (COOL) (ºC) This parameter lets cnfigure the delta temperature that will be applied when the timeut is extinguished. Imprtant: When there is ccupancy again after the applicatin f a delta, the same delta will be applied inversely as explained abve. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 37 / 48

IntesisBx KNX IR Universal AC Relad last On/Off value when Occupied If set t n, nce the switch-ff timeut has elapsed, any value will be reladed. If set t yes, nce the switch-ff timeut has elapsed, the last On/Off value will be reladed. If a 1 value is sent t the Cntrl_ Occupancy bject after the timeut perid, the indr unit will turn n. If a 0 value is sent t the Cntrl_ Occupancy after the timeut perid n actin will be perfrmed. Lck ON when ccupied If set t n, On/Off cmmands while the rm is ccupied will be accepted. If a 1 value is sent t the Cntrl_ Switch Off Timeut bject the switch-ff timeut perid will begin again. If a 0 value is sent t the Cntrl_ Switch Off Timeut bject, n actin will be perfrmed. If set t yes, On/Off cmmands, while the windw is pen, will be saved (but nt applied). These cmmands will be used in the next parameter if set t yes. Binary Input x cnfiguratin dialgs All the parameters in this sectin are related with the binary inputs prperties and cmmunicatin bjects. 5.11.1 Enable use f Input x This parameter enables the use f the Input x. If set t n the bjects will nt be shwn. If set t yes the Status_ Inx bject(s) and new parameters will appear. Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 38 / 48

IntesisBx KNX IR Universal AC 5.11.2 Cntact type This parameter lets chse the behavir that will have the binary input depending n if the cntact is nrmally pen r nrmally clsed. There are tw pssible ptins t cnfigure the cntact type: NO: Nrmally Open and NC: Nrmally Clsed. 5.11.3 Debunce time This parameter lets chse a debunce time (in millisecnds) that will be applied t the cntact. 5.11.4 Disabling functin This parameter shws/hides the Cntrl_ Disable Input x cmmunicatin bject which will let disable/enable the input x. If set t n any bject will be shwn. When DPT 1.003: 0-Disable; 1-Enable is selected, the input can be disabled using the value 0 and enabled using the value 1. When DPT 1.002: 1-True (Disable); 0-False (Enable) is selected, the input can be disabled using the value 1 and enabled using the value 0. 5.11.5 Functin This parameter lets chse the functin that will have the binary input. There are 3 different functins available: Occupancy (internal), On/Off and Windw Cntact (internal). When Occupancy is selected, the binary input x will have the same behavir as cnfigured in the parameter Occupanys (sectin 5.10). When On/Off is selected, the AC unit will turn ff when the binary inpyt x is active. When Windw Cntact (internal) is selected, the binary input x will have the same behavir as cnfigured in the parameter Windw Cntact (sectin 5.9). Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 39 / 48

IntesisBx KNX IR Universal AC 6 Electrical and Mechanical features Enclsure Dimensins ABS (V-0). 2,1 mm thickness PC (V-2). 1 mm thickness 81 x 78 x 28 mm Weight Clr Pwer supply Munting LED indicatrs Push buttns 76 g Ivry white 29V DC, 17mA Supplied thrugh KNX bus Wall and desktp 1 x Device status and KNX prgramming 1 x KNX prgramming. 2 x binary inputs fr ptential-free cntacts. Signal cable length: 5m unshielded, may be extended up t 20m with twisted. Binary inputs Cnsle prt Cnfiguratin Operating Temperature Operating humidity Stck humidity Cmpliant with the fllwing standards: IEC61000-4-2: level 4-15kV (air discharge) - 8kV (cntact discharge) MIL STD 883E-Methd 3015-7: class3b Mini USB prt fr cnsle usage Cnfiguratin with ETS Frm 0ºC t 40ºC <93% HR, n cndensatin <93% HR, n cndensatin 27 mm 78 mm 28 mm 3 mm 81 mm 26 mm Intesis Sftware S.L.U. - All rights reserved This infrmatin is subject t change withut ntice IntesisBx is a registered trademark f Intesis Sftware SLU http://www.intesisbx.cm inf@intesisbx.cm 40 / 48