VCE = 45 V IC = 5 A ABB HiPak TM IGBT Module 5SNG 5P453 Doc. No. 5SYA 593-4 7-23 Ultra low loss, rugged SPT + chip-set Smooth switching SPT + chip-set for good EMC High iulation package AlSiC base-plate for high power cycling capability AlN substrate for low thermal resistance Recognized under UL557, File E96689 Maximum rated values ) Parameter Symbol Conditio min max Unit Collector-emitter voltage VCES VGE = V 45 V DC collector current IC Tc = 8 C 5 A Peak collector current ICM tp = ms, Tc = 8 C 3 A Gate-emitter voltage VGES -2 2 V Total power dissipation Ptot Tc = 25 C, per switch (IGBT) 45 W DC forward current IF 5 A Peak forward current IFRM 3 A Surge current IGBT short circuit SOA IFSM tpsc VR = V, Tvj = 25 C, tp = ms, half-sinewave VCC = 34 V, VCEM CHIP 45 V VGE 5 V, Tvj 25 C 4 A µs Isolation voltage Visol RMS, min, f = 5 Hz 74 V Junction temperature Tvj 25 C Junction operating temperature Tvj(op) -5 25 C Case temperature Tc -5 25 C Storage temperature Tstg -5 25 C Mounting torques 2) Ms Base-heatsink, M6 screws 4 6 Mt Main terminals, M6 screws 4 6 ) Maximum rated values indicate limits beyond which damage to the device may occur per IEC 6747 2) For detailed mounting itructio refer to ABB Document No. 5SYA239 Nm
5SNG 5P453 IGBT characteristic values 3) Parameter Symbol Conditio min typ max Unit Collector (-emitter) breakdown voltage Collector-emitter 4) saturation voltage V(BR)CES VGE = V, IC = ma, Tvj = 25 C 45 V VCE sat IC = 5 A, VGE = 5 V Collector cut-off current ICES VCE = 45 V, VGE = V Tvj = 25 C 2.75 V Tvj = 25 C 3.5 V Tvj = 25 C 2 ma Tvj = 25 C 6 2 ma Gate leakage current IGES VCE = V, VGE = 2 V, Tvj = 25 C -5 5 na Gate-emitter threshold voltage VGE(TO) IC = 4 ma, VCE = VGE, Tvj = 25 C 5.5 6.2 7.5 V Gate charge Qge IC = 5 A, VCE = 28 V, VGE = -5 V.. 5 V Input capacitance Cies 7.5 VCE = 25 V, VGE = V, f = MHz, Output capacitance Coes.2 Tvj = 25 C Reverse trafer capacitance Cres.32 Turn-on delay time Rise time Turn-off delay time Fall time Turn-on switching energy Turn-off switching energy Short circuit current td(on) tr td(off) tf Eon Eoff ISC VCC = 28 V, IC = 5 A, RG = 5, VGE = 5 V, L = 4 nh, inductive load VCC = 28 V, IC = 5 A, RG = 5, VGE = 5 V, L = 4 nh, inductive load VCC = 28 V, IC = 5 A, VGE = ±5 V, RG = 5, L = 4 nh, inductive load VCC = 28 V, IC = 5 A, VGE = ±5 V, RG = 5, L = 4 nh, inductive load tpsc μs, VGE = 5 V, Tvj = 25 C, VCC = 34 V, VCEM CHIP 45 V Tvj = 25 C 53 Tvj = 25 C 5 Tvj = 25 C 2 Tvj = 25 C 3 Tvj = 25 C 5 Tvj = 25 C 72 Tvj = 25 C 4 Tvj = 25 C 59 Tvj = 25 C 45 Tvj = 25 C 58 Tvj = 25 C 44 Tvj = 25 C 65 36 nc nf mj mj 66 A Module stray inductance L DC between C E2 25 nh Resistance, terminal-chip RCC +EE between C E2 3) Characteristic values according to IEC 6747 9 4) Collector-emitter saturation voltage is given at chip level TC = 25 C.78 TC = 25 C.3 mω Doc. No. 5SYA 593-4 7-23 page 2 of 9
5SNG 5P453 Diode characteristic values 5) Parameter Symbol Conditio min typ max Unit Forward voltage 6) VF IF = 5 A Reverse recovery current Recovered charge Reverse recovery time Reverse recovery energy 5) Characteristic values according to IEC 6747 2 6) Forward voltage is given at chip level Irr Qrr trr Erec VCC = 28 V, IF = 5 A, VGE = 5 V, RG = 5 L = 4 nh inductive load Tvj = 25 C 3.2 Tvj = 25 C 3.45 Tvj = 25 C 27 Tvj = 25 C 35 Tvj = 25 C 4 Tvj = 25 C 235 Tvj = 25 C 78 Tvj = 25 C 33 Tvj = 25 C 25 Tvj = 25 C 385 V A µc mj Package properties 7) Parameter Symbol Conditio min typ max Unit IGBT thermal resistance junction to case Diode thermal resistance junction to case Rth(j-c)IGBT.62 K/W Rth(j-c)DIODE.22 K/W IGBT thermal resistance 2) case to heatsink Rth(c-s)IGBT IGBT per switch, grease = W/m x K.48 K/W Diode thermal resistance 7) case to heatsink Partial discharge extinction voltage Rth(c-s)DIODE Diode per switch, grease = W/m x K.96 K/W Ve f = 5 Hz, QPD pc (acc. to IEC 6287) 35 V Comparative tracking index CTI 6 2) For detailed mounting itructio refer to ABB Document No. 5SYA239 Mechanical properties 7) Parameter Symbol Conditio min typ max Unit Dimeio L x W x H Typical, see outline drawing 73 x 4 x 48 mm Clearance distance in air Surface creepage distance da ds according to IEC 6664- and EN 524- according to IEC 6664- and EN 524- Term. to base: 35 Term. to term: 9 Term. to base: 64 C to E: 54 C to E2: 78 Mass m 62 g 7) Package and mechanical properties according to IEC 6747 5 mm mm Doc. No. 5SYA 593-4 7-23 page 3 of 9
5SNG 5P453 Electrical configuration C 4 C G E 5 6 2 C 2 / E G2 8 E2 7 3 E2 Outline drawing 2) Note: all dimeio are shown in mm 2) For detailed mounting itructio refer to ABB Document No. 5SYA239 This is an electrostatic seitive device, please observe the international standard IEC 6747-, chap. IX. This product has been designed and qualified for Industrial Level. Doc. No. 5SYA 593-4 7-23 page 4 of 9
5SNG 5P453 3 3 V CE = 25 V 25 25 25 C 2 2 IC [A] 5 25 C IC [A] 5 25 C 5 5 25 C V GE = 5V 2 3 4 5 6 2 3 4 5 6 7 8 9 2 3 4 V CE [V] V GE [V] Fig. Typical on-state characteristics, chip level Fig. 2 Typical trafer characteristics, chip level 3 25 7 V 5 V 3 V 3 25 7 V 5 V 3 V 2 2 IC [A] 5 V IC [A] 5 V 5 9 V 5 9 V 2 3 4 5 V CEsat [V] T vj = 25 C 2 3 4 5 6 V CEsat [V] T vj = 25 C Fig. 3 Typical output characteristics, chip level Fig. 4 Typical output characteristics, chip level Doc. No. 5SYA 593-4 7-23 page 5 of 9
5SNG 5P453.8.6.4.2 V CC = 28 V R G = 5 ohm V GE = ±5 V T vj = 25 C L = 4 nh E on E off.6.4.2 V CC = 28 V I C = 5 A V GE = ±5 V T vj = 25 C L = 4 nh E on Eon, Eoff [J].8.6 Eon, Eoff [J].8.6 E off.4.4.2.2 E sw [J] = 8.5 x -6 x I C 2 + 5.6 x -3 x I C +.4 5 5 2 25 3 35 2 4 6 8 I C [A] R G [ohm] Fig. 5 Typical switching energies per pulse vs collector current Fig. 6 Typical switching energies per pulse vs gate resistor t d(off) t d(off) td(on), tr, td(off), tf [µs].. t f t d(on) t r V CC = 28 V R G = 5 ohm V GE = ±5 V T vj = 25 C L = 4 nh 5 5 2 25 3 35 td(on), tr, td(off), tf [µs].. t d(on) 2 3 4 5 6 7 8 t f t r V CC = 28 V I C = 5 A V GE = ±5 V T vj = 25 C L = 4 nh I C [A] R G [ohm] Fig. 7 Typical switching times vs collector current Fig. 8 Typical switching times vs gate resistor Doc. No. 5SYA 593-4 7-23 page 6 of 9
5SNG 5P453 2 C ies V GE = V f OSC = MHz V OSC = 5 mv 5 V CC = 28 V V CC = 36 V C [nf] C oes VGE [V] C res 5 I C = 5 A T vj = 25 C. 5 5 2 25 3 35 V CE [V].2.4.6.8.2 Q g [µc] Fig. 9 Typical capacitances vs collector-emitter voltage Fig. Typical gate charge characteristics 2.5 V CC 34 V, T vj = 25 C, V GE = ±5 V R Goff = 5 ohm, L 4 nh 2.5 ICpulse / IC.5 Chip Module 2 3 4 5 V CE [V] Fig. Turn-off safe operating area (RBSOA) Doc. No. 5SYA 593-4 7-23 page 7 of 9
5SNG 5P453 6 5 Erec.45.4.35 V CC = 28 V I F = 5 A T vj = 25 C L = 4 nh I rr 45 4 35 Erec [mj], Irr [A], Qrr [µc] 4 3 2 Qrr Irr VCC = 28 V RG = 5 ohm Tvj = 25 C L = 4 nh Erec [J].3.25.2.5..5 E rec RG = 68 ohm RG = 47 ohm RG = 33 ohm RG = 22 ohm RG = 5 ohm RG = ohm Q rr 3 25 2 5 5 Irr [A], Qrr [µc] 5 5 2 25 3 35 5 5 2 25 IF [A] di/dt [A/µs] Fig. 2 Typical reverse recovery characteristics vs forward current Fig. 3 Typical reverse recovery characteristics vs di/dt 3 25 2 25 C 4 35 3 25 V CC 34 V di/dt 25 A/µs T vj = 25 C L 4 nh IF [A] 5 25 C IR [A] 2 5 5 5 2 3 4 5 2 3 4 5 V F [V] V R [V] Fig. 4 Typical diode forward characteristics, chip level Fig. 5 Safe operating area diode (SOA) Doc. No. 5SYA 593-4 7-23 page 8 of 9
Z th(j-c) [K/W] IGBT, DIODE 5SNG 5P453 Analytical function for traient thermal impedance:. Z th(j-c) Diode Z th(j-c) IGBT Z th (j-c) (t) = n i R i (- e -t/ i i 2 3 4 5 ). IGBT Ri(K/kW) 4.2 3.68 6.72 i(ms) 92.6 2.4 2.78 DIODE Ri(K/kW) 8 28.4 3.84 i(ms) 9.5 22.6 3..... t [s] Fig. 6 Thermal impedance vs time For detailed information refer to: 5SYA 242 Failure rates of HiPak modules due to cosmic rays 5SYA 243 Load cycle capability of HiPaks 5SYA 245 Thermal runaway during blocking 5SYA 258 Surge currents for IGBT diodes 5SZK 92 Specification of environmental class for HiPak ABB Switzerland Ltd Doc. No. 5SYA 593-4 7-23 Semiconductors Fabrikstrasse 3 CH-56 Lenzburg, Switzerland Telephone +4 ()58 586 49 Fax +4 ()58 586 36 Email abbsem@ch.abb.com Internet www.abb.com/semiconductors