12' Octagon Wood Gazebo

Transcription

1 12' Octagon Wood ANY REPRODUCTION, ALTERNATION, OR USE OF STARTING ANY DISCEPANCY SHALL BE REPORTED IN WRITTING BEFORE STARTING DESIGN REQUIREMENTS 1. Governing Code: Including, not limited to: IBC 2015 (ASCE 7-05) Risk Category: 1 2. Dead Load: 5 psf 4. Ground Snow Load: 30 psf 5. Wind Load: Basic Wind Speed (V): 110 mph Exposure Class: B Open Building, Unrestricted Flow Cover Page DATE: 10/19/2017 PAGE: 1 of 6 JR. SCALE: 1:48

2 Framing Elevation " " " Elevation (2) 2x4 pressure treated SYP Floor Joist, fasten together w/ #8x3" screws Elevations " Post Layout Plan " " Floor Framing Plan 2x4 pressure treated SYP band Board, fasten to each floor joist w/ (2) #8x3" screws 1x4 Cedar Trim Board, fasten to band board w/ (3) #8x1 5/8" screws 2x4 pressure treated SYP floor Joist, fasten at each end w/ #8x3" screws DATE: 10/19/2017 PAGE: 2 of 6 JR. SCALE: 1:64

3 F " B " together w/ s, Detail E (4) Ply 2x8 SYP compression ring, 2nd ply fasten to 1st ply w/ s, 3rd ply to 2nd ply w/ #8x3" screws, 4th ply to 3rd ply w/ #8x3" screws. Roof Framing Plan 2x4 SYP fascia, fasten to 2x4 rafter at each end w/ #8x3" screws B F Roof Framing Plan 1x4 Cedar Trim, fasten to 2x4 fascia w/ (3) #8x1 1/2" screws DATE: 10/19/2017 PAGE: 3 of 6 JR. SCALE: 1:32

4 " (4) Ply 2x8 SYP compression ring, 2nd ply fasten to 1st ply w/ s, 3rd ply to 2nd ply w/ #8x3" screws, 4th ply to 3rd ply w/ #8x3" screws, and to each ply of rafter w/ (1) #8x3" screw from bottom " ga. Roof Bracket, fasten to ceiling boards and rafters and band board below w/ (16) 10d nails T-Rail consisting of a 2x4 flat and 2x2 on Detail C edge, fasten together w/ #8x2 1/2" screws, is notched 1/8" to accept 2x4 2x6 cedar brace, fasten to and T-rail w/ (2) #8x3" screws, fasten T-rail to w/ (2) #8x3" screws 1x6 SYP tongue & groove decking, fasten to rafters at each end w/ (2) 2" nails together w/ s, 1x4 Cedar Trim Board, fasten to fascia board w/ (3) #8x1 5/8" screws 2x4 SYP fascia, fasten to 2x4 rafter at each end w/ #8x3" screws Cross Section With Floor " Detail D 2x4 #1 cedar top rail, fasten to w/ #8x3" screws, (2) at each end, is notched 1/8" to accept this rail 2x3 #1 cedar bottom rail. fasten to w/ #8x3" screws, (2) at each end 36" 1x3 cedar spindles 5/4x6 cedar decking CROSS SECTION B-B With Floor 2x4 pressure treated SYP floor Joist, fasten at each end w/ #8x3" screws DATE: 10/19/2017 PAGE: 4 of 6 JR. SCALE: 1:32

5 2x4 SYP fascia, fasten to 2x4 rafter at each end w/ #8x3" screws 1x4 Cedar Trim Board, fasten to fascia board w/ (3) #8x1 5/8" screws 2" 1 4 " Detail C 18 ga. Roof Bracket, fasten to ceiling boards and rafters and band board below w/ (16) 10d nails together w/ s, Post is notched to accept 2x4 rafter, outside plies of to extend to top of rafters 3 1 2" 1 4 " 1 1 2" Post Bracket Detail 2"x3 1/2"x1 1/2" 18 ga. "L" bracket, fasten to w/ (4) s, and to floor w/ (2) #12x4" timberlock screws 6" 1x6 SYP tongue & groove decking, fasten to rafters at each end w/ (2) 2" nails Detail Views 1x4 Cedar Trim Board, fasten to band board w/ (3) #8x1 5/8" screws Detail D With Floor 2x4 pressure treated SYP floor Joist, fasten at each end w/ #8x3" screws 2x4 pressure treated SYP band Board, fasten to each floor joist w/ (2) #8x3" screws 18 ga. Roof Bracket, fasten to ceiling boards and rafters and band board below w/ (16) 10d nails 12" 1x4 Cedar Trim Board, fasten to fascia board w/ (3) #8x1 5/8" screws Detail E DATE: 10/19/2017 PAGE: 5 of 6 JR. SCALE: 1:32

6 " " 18 ga. Roof Bracket, fasten to ceiling boards and rafters and band board below w/ (16) 10d nails 12 T-Rail consisting of a 2x4 flat and 2x2 on edge, fasten together w/ #8x2 1/2" screws, is notched 1/8" to accept 2x4 (4) Ply 2x8 SYP compression ring, 2nd ply fasten to 1st ply w/ s, 3rd ply to 2nd ply w/ #8x3" screws, 4th ply to 3rd ply w/ #8x3" screws, and to each ply of rafter w/ (1) #8x3" screw from bottom 1x6 SYP tongue & groove decking, fasten to rafters at each end w/ (2) 2" nails together w/ s, 1x4 Cedar Trim Board, fasten to fascia board w/ (3) #8x1 5/8" screws " " Detail G 2x6 cedar brace, fasten to and T-rail w/ (2) #8x3" screws, fasten T-rail to w/ (2) #8x3" screws 2x4 #1 cedar top rail, fasten to w/ #8x3" screws, (2) at each end, is notched 1/8" to accept this rail 2x3 #1 cedar bottom rail. fasten to w/ #8x3" screws, (2) at each end 36" 1x3 cedar spindles Cross Section Without Floor CROSS SECTION F-F Without Floor 2"x3 1/2"x1 1/2" 18 ga. "L" bracket, fasten to w/ (4) s, and to Deck or concrete foundation by others w/ (2) #12x2 1/2" screws Detail G DATE: 10/19/2017 PAGE: 6 of 6 Without Floor SCALE: JR. 1:32