SCHWERE PLATTFORMWAGON TYPE SSY 60TON
|
|
- Tyrone Brooks
- 5 years ago
- Views:
Transcription
1 TWS 5094 SCHWERE PLATTFORMWAGON TYPE SSY 60TON Congratulations on purchasing one of the finer aftermarket resin kits sets available. The photo below is of the completed kit. The Panther tank is not included with this kit. You will note that we have broken the build into several sub-assemblies. Please note each sub assembly will have it s own parts list as well as part numbers. So look over these instructions to get familiar with what will be involved in the construction of this kit. You will also need to have some additional supplies to complete this kit. You will need some 5 minuet epoxy, wood glue and several drill bits. The drill bit numbers will be called out on the respective sub assemble. We also recommend you have a set of track to aid in the truck assembly. Tank Workshop sells a three piece set of track TWS We can also recommend Trumpeter's German Railway Track set kit # We recommend washing the parts in warm soapy water or a commercially available mold release cleaner to remove any residual mold release agent. We also recommend leaving the parts on the casting blocks until called out for. Once the part is called out for dry fit to make sure the parts fit and align properly Assembly The first sub-assembly will be the frame of the car. Please reference the next page for the parts list and the assembly steps. We recommend you use a square to make sure the frame is perfectly square. You may use the provided wooden deck to make sure you fit the frame together squarely.
2 Frame Parts List 4x x x Frame Sub-Assembly 1. Use the below line drawings as a reference to the basic layout of the frame. Join parts 1 and together. Then join parts to one set of the side frame reference figure 1. Check to make sure parts are square to parts 1&. Once you have checked this then glue the second frame set to parts. You now can test fit the wood decking into the basic frame. The fit will be tight and there should be no gaps on the sides or ends. Next test fit parts 4 to the locating bars on the insides of parts 1&. Part 4 should drop right in without pushing the frame sides out. If this happens then you ll have 4 waves in your frame and the deck will have gaps. If you need to trim part 4 then note that you ll need to remove an equal amount from both sides so the truck locating pin remains centered in the car. For example if you need to remove a total of 4mm then you must remove mm from either side. See figure for the completed frame. 4 1& assembly
3 4 Note how part is joined to the side frame. The side frame will have a little overhang from the end piece Fig. 1 Fig. Note center support beam not included with kit. This can be added for extra support but is not necessary
4 Truck Parts 8x8 6x16 5x8 7x16 9x8 4x8 x8 x8 11x 10x8 1x4 Not shown /16 plastic tube &.06 plastic rod Truck Sub-assembly 1. Begin by installing parts into the wheel axel support slots on parts 1. See figure 1 for reference. Note that the flanges on part will be on the back side of part 1. Next install part 5 to the lower end of the wheel bearing box support slot. It should cover part. See figure. Next install part 8 to the top of part 5. The spring support ends should be glued to the locating circles on part 1. Next install part 9 to the lower end of the bearing box.. Next you ll need to build the brake support assemblies using parts and 6. You ll need to drill out part 6 at the locating hole using a #5 drill bit. Next using the.06 rod as a jig you ll need to install two rod support arms onto the rod. NOTE THE ANGLE OF THE SUPPORTS. See figure. Using this jig then glue part 6 to the locating slots on part. You will need to do this 8 times.. Next build the axel using the /16 tubing. The length of the axel should be 5.8cm. Next measure 4mm from both ends. This is the portion of the axels that will go into the bearing boxes on the truck frames. Slide two each of part 4 onto the axel. Cone ends facing each other. Now slide the wheels (10) on. The wheel should be set to the 4mm line. See figure 4 4
5 Fig NOTE: You may need to sand the bearing box block () flat with the truck frame (1) before installing part 5. Part 5 should sit flat against the truck frame Fig. 8 5 Fig FWD.06 Rod NOTE direction of brake bar support 5
6 Fig Next you will need to assemble the truck. We recommend slow setting super glue for this step. This is where a set of track becomes useful. Slide the axel/wheel assembly into the bearing boxes. Now set the assembly onto the rails and make sure it sits flat. If it sits flat disassemble and then glue the axels into the bearing boxes while holding the assembly on the track. Now install the brake support sub-assemblies to the ends of the truck frames. See figure 5. Once you are happy with the set of the truck on the rails and the entire assembly is square then go ahead and put some super glue accelerator on all the joints to speed up the slow setting super glue. Now install the two remaining brake support sub-assemblies into the slots on the truck frames. Some trimming may be necessary for these to slide into place. See figure Now it s time to install the brake pads and rods. Using the.06 rod cut 4.7cm lengths. Now slide into the support arms and glue the brake pads to the ends. The pads should sit away from the wheels or you can adjust them to be engaged with the wheel showing the brakes applied. Fig. 5 Note the truck assembly is being viewed from the bottom 6
7 6. Final step in the truck assembly is installing the truck pivot plate to the to the top of the truck assembly. This plate should be centered on the truck. See figure Fig. 6 Hitch/Bumper Parts 15x4 16x4 1 14x4 1x 11x 10x4 9x 8x 7x4 6x4 5x4 x4 4x4 x4 1x4 Not shown 17, 18,.040 plastic rod 7
8 Hitch/Bumper Assembly 1. Now we will assemble the bumpers and hitches to the car ends. Using figure 1 make the appropriate measurements and then glue the called out parts to the measurements. Before gluing part 1 to the car end you will need to drill out the top of the hook with a #60 drill bit at the locator holes. 10mm Fig. 1 5mm mm 9mm. Next you will need to drill out parts 6&11 using a #47 drill bit. This will allow the jack screw to slide into the blocks and the adjust handle to slide between the blocks. Now drill out parts 10,1 and the other side of part 6 using a #60 drill bit. I recommend you do the drilling with the parts still attached to the casting block. Now assemble the hitch assembly per figure..040 Rod 1 10 Fig Rod. Now install ea air valves to the car ends between part 1 and 1. Next using some tubing install part 5 on the end and install into one of the air control valves. Using another piece of tubing install part 7 and install into the other valve. See figure. 8
9 Fig install at 4 corners approx 1.5cm from end 18 9 Fig. 4 9
10 Final Assembly Now for final assembly. First you will need to glue the upper and lower decks together using a wood glue or epoxy. Note the alignment of the bolt holes. The lower deck hole should be close to the center of the upper deck hole. I recommend using a flat weight to aid in the two pieces of decking to dry flat together. NOTE: THE WOOD DECK MAY WARP IF NOT WEIGHTED WHILE DRYING. At this time you can stain your deck if that is your desired finish. After the decks are dry install them into the car frames using a 5 minuet epoxy. I can t recommend super glue as a bonding agent as I did not try this. So if using super glue use at your own risk. Once the decking is secure you can install the trucks to the mounts on the frame. There should be an air tank installed along the centerline of the lower deck between the two truck assemblies. Use epoxy to attach this. Final step would be to install the rivets/bolts in the recessed bolt holes in the deck. You can either trim the rivets/bolts to sit flush in the deck or you can drill out the lower deck holes using a #6 drill bit. By doing this you can just cut the rivet off of it s tree and slide it in the hole. No trimming required. Rivets/Bolts installed If you reference the hitch/bumper parts list you will note parts 15 and 16. Part 16 can be installed on the deck as guides to keep the loaded tank centered on the deck. These are optional. Part 15 are wooden chocks used to chock the tank once on the deck. 10
11 Decals & Painting Use the below figure to locate the decals. Note if you are building the Panther car please reference the notes on the figure for the applicable car s decals. For painting we recommend you browse the various railroad car colors at your local hobby shop or on-line shop. These cars could be painted several colors from a dark grey, black or even red. Some may have even been camouflaged. The decking can be stained or painted. You can use a wire brush to distress the wood and give it a worn, torn up look. Tank treads were not easy on this wood. Look for good references to choose the colors. Even use modern day rail cars as reference. White For Panther use this decal TWS 00 uses 60ton symbol White 45 Wynbrook Dr. McDonough GA 05 Copyright tankworkshop@charter.net Ph:
CONCEPT MODELS INSTRUCTIONS FOR THE KASGRO KRL SPECIAL DEPRESSED CENTER FLAT CARS El Toro Way Stockton, CA 95210
CONCEPT MODELS Web Address: http://www.con-sys.com Email: concept_models@con-sys.com 8810 El Toro Way Stockton, CA 95210 INSTRUCTIONS FOR THE KASGRO KRL 204000-2 SPECIAL DEPRESSED CENTER FLAT CARS 2 CONCEPT
More informationTool Wagon Assembly Instructions
Tool Wagon Assembly Instructions Adhesives Wood to wood joints are best done with a PVA wood glue but a good quality, slow acting (beware of instant grab ) cyanoacrylate super glue can be used if preferred.
More informationCONCEPT MODELS SP DOUBLE STACK CONTAINER CARS INSTRUCTIONS Sheep Ranch Rd. Mountain Ranch, CA Web Address:
CONCEPT MODELS Web Address: http://www.con-sys.com 8331 Sheep Ranch Rd. Mountain Ranch, CA 95246 SP DOUBLE STACK CONTAINER CARS INSTRUCTIONS 2 CONCEPT MODELS PARTS Item No. PART NO. DESCRIPTION QTY. 1
More informationBRITISH STYLE WADING STACKS FOR SHERMAN III
TWS 351002 BRITISH STYLE WADING STACKS FOR SHERMAN III Congratulations on purchasing one of the finer aftermarket resin conversion sets available. The kit you are about to build was mastered by Karl van
More informationCONCEPT MODELS INSTRUCTIONS FOR PRODUCT 60,000 GALLON TANK CAR El Toro Way Stockton, CA 95210
CONCEPT MODELS Web Address: http://www.con-sys.com Email: concept_models@con-sys.com 8810 El Toro Way Stockton, CA 95210 INSTRUCTIONS FOR PRODUCT 60,000 GALLON TANK CAR 2 CONCEPT MODELS PARTS GATX/UTLX
More information1. Underframe/Tank Bottom
1. Underframe/Tank Bottom The construction process for the Class X tank cars is a little different as there is no true underframe. Instead we will use the tank bottom as part of the underframe, attaching
More informationCONCEPT MODELS UTLX 80006,80020 CRYOGENIC TANK CAR KIT INSTRUCTIONS Sheep Ranch Rd. Mountain Ranch, CA 95246
CONCEPT MODELS Web Address: http://www.con-sys.com Email: concept_models@con-sys.com 8331 Sheep Ranch Rd. Mountain Ranch, CA 95246 UTLX 80006,80020 CRYOGENIC TANK CAR KIT INSTRUCTIONS 2 CONCEPT MODELS
More informationPeter Krause ABN
Peter Krause ABN 25 736 637 163 T/as O-Aust Kits PO Box 743 ALBANY CREEK QLD 4035 AUSTRALIA Phone +61 (0)7 3298 6283 (7.00pm to 9.30pm ONLY) Facsimile +61 (0)7 3298 6287 (24 hours) Mobile 0419 680 584
More informationSE5a Instrument Board part 2 - rev 1.1
SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any
More informationTrim down the piece of casting being pointed to with the tip of the pencil in the first picture. It is only the 'inboard casting that needs to be
1. File off the moulding pips from the wheel flanges. File the ends of the tube smooth and de-burr. Assemble the wheel sets with a drop of car engine oil on the axles. Glue the wheel sets into place. 2.
More information-1- Coach Instructions.
-1- Coach Instructions. Insert the bogie pivot pins through the bottom of the coach body ensuring the dimples fit into the recesses. Glue the.06 x.25 short strips each side of the pivot head, bridge the
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationSwift assembly guide
Swift assembly guide Download the assembly guide at www.scihighmodels.com/swift.pdf Sample kit shown with aluminium bells (available with the Deluxe kit) Shown here without main tanks Version 10/12/2010
More informationPS 5077 cu. ft. Boxcar with EOC device. 1:29 scale resin craftsman kit. by Burl Rice
PS 5077 cu. ft. Boxcar with EOC device 1:29 scale resin craftsman kit by Burl Rice www.burlrice.com Bill of materials (not included): Thick/medium viscosity CA PL adhesive, or Gorilla Glue Heavy Duty Construction
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationSouthern Pacific C-30-4/6 Bay Window Caboose N-Scale & HO-Scale
Southern Pacific C-30-4/6 Bay Window Caboose N-Scale & HO-Scale Before Starting PREPARING BRASS The easiest way to remove the brass parts from the sheet they are produced on, is to use rail nippers. The
More information40 & 50 Foot PS-1 Box Car Assembly Instructions
40 & 50 Foot PS-1 Box Car Instructions Push the #2100 coupler/stirrup assembly onto the ends of the metal floor. Slide them into the slots and slightly lift the ends (wings), then press firmly on the front
More information7/8n2 Scale Plantation Coach
7/8n2 Scale Plantation Coach Introduction This small coach modeled in 7/8 n2 was inspired from a Hawaiian Railway Company plantation excursion car from the late 19 century. While not an exact replica,
More information28 ft. Ventilated (Combination) Box Car
28 ft. Ventilated (Combination) Box Car Introduction This laser cut wood kit is an HO scale model of a 28 ft. Ventilated (also known as a Combination) Box Car. The model is based on the Illinois Central
More informationBRF-022 YGH SEALION. Building Instructions
Tel 07747 018544 www.prmrp.com BRF-022 YGH SEALION Building Instructions SCALE MODEL PRODUCT FOR ADULT MODELLERS ONLY. WHITE METAL CONTAINS LEAD WASH HANDS AFTER USE. MAY CONTAIN SMALL PARTS. ETCHED BRASS
More informationPrecision Steel Car s 100 T Steel Coil Car
Precision Steel Car s 100 T Steel Coil Car Precision Steel Car www.precisionsteelcar.com info@precisionsteelcar.com Paul Vernon: (513) 571-5739 Revised 4/30/2009 Contents of Kit Main Tube Side Frame 2
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2738 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationInstallation Instructions
TOYOTA 16K Industry Standard Rail Custom Mounting Kit #2748 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationRight On Replicas, LLC Step-by-Step Review * Panzer IV Tank 1:32 Scale Monogram Model Kit # Review
Right On Replicas, LLC Step-by-Step Review 20150108* Panzer IV Tank 1:32 Scale Monogram Model Kit #85-7861 Review The Panzer tank was used throughout World War II and had several modifications during that
More informationCA to each one. You may have to hold the end down while to glue sets or use an accelerator like I did.
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationAfter the glue dries, trim the trussrod ends with your cutting pliers
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationInstructions: GSC 60 Flatcar Kit with or without bulkheads Tangent Part Number: and /2016
Instructions: GSC 60 Flatcar Kit with or without bulkheads Tangent Part Number: 11000-01 and 11000-02 5/2016 Thank you for purchasing the Tangent Scale Models GSC 60 Flatcar Kit! A few quick notes before
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part
More information12. Wings, Flaps, Ailerons and Struts
12. Wings, Flaps, Ailerons and Struts Fit Aileron Hinges Reference: Drawing 20270K2 Photo 12.1 Parts Required: 2007092 Aileron LS 200809N Aileron RS 2001394 Hinge 3/16 A1 (4) 2001694 Hinge Pin (4) PH0059N
More informationZiroli D-17 Beech Staggerwing
Ziroli D-17 Beech Staggerwing Parts List Vacuform Parts: Miscellanous Pieces 1 Four Side Panels 1 3/16" Tube, 2" Long 2 Lower Dash - Back Dash 2 Felt, 12x24 3 Dash 3 Cordury 12x24 4 Dash Hood 4 Aluminum
More information1104. Clean up the door striker plates with a hand grinder using a wire brush and WD-40.
Chapter 31 - Misc. Putting VW Back Together (Video Clip 31) 1104. Clean up the door striker plates with a hand grinder using a wire brush and WD-40. 1105. Install both door striker plates on the VW body
More informationO-Aust Kits. QR Class CLF Louvred Wagon Kitset in O Scale 1:48
O-Aust Kits PO Box 743 ALBANY CREEK QLD 4035 AUSTRALIA Phone +61 (0)7 3298 6283 (7.00pm to 9.30pm ONLY) Facsimile +61 (0)7 3298 6287 (24 hours) Mobile 0419 680 584 Email pa_rl_krause@bigpond.com Web www.oaustkits.com.au
More informationINTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D APPLICATION: F87 M2
INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D330-0026 APPLICATION: 2016-17 F87 M2 Congratulations for being selective enough to use a Dinan Intercooler Upgrade Kit. We have spent many hours
More informationCALIBURN ASSEMBLY INSTRUCTIONS
CALIBURN ASSEMBLY INSTRUCTIONS The Caliburn is a Mag-Fed Pump-Action Homemade Nerf Blaster design released as a Public Domain license file set by Captain Slug (http://www.captainslug.com). You are welcome
More informationCONCEPT MODELS INSTRUCTIONS FOR UP DC-10 WING CAR El Toro Way Stockton, CA Web Address:
CONCEPT MODELS Web Address: http://www.con-sys.com 8810 El Toro Way Stockton, CA 95210 INSTRUCTIONS FOR UP DC-10 WING CAR 2 CONCEPT MODELS PARTS DC-10 WING CAR Item No. Part No. DESCRIPTION QTY. 1 2003-1
More informationInstructions: PS-2CD 4000 Model Kit Revised 7/2008
Instructions: PS-2CD 4000 Model Kit Revised 7/2008 Plastic Parts included: Body shell Parts Sprue #1 Roof, trainline, gravity outlet gates, and centersill/endsill pieces Parts Sprue #2 Underframe bolster
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationFurness Railway Wagon Co. Glasgow & South Western Railway/LMS/BR ton Box Van Steel Under-Frame
Furness Railway Wagon Co. Glasgow & South Western Railway/LMS/BR 1920 10ton Box Van Steel Under-Frame Wheels, paint and transfers required to complete. Please note that to aid the folding of the various
More informationInstallation Instructions
CHEVY / GMC 16K Industry Standard Rail Custom Mounting Kit #2730 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationContinue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below
Radiator rev 1.1 The SE5a s radiator is one of the most recognized radiators in WW1. It is one of the components that defines the SE5a. The original SE5a has seen multiple radiator designs used during
More informationMLS MasterClass 2002
MLS MasterClass 2002 Build a 2-6-6T / 0-6-6T Mason Bogie An Adventure in 1:20.3 By Doc Watson Chapter 6 - A Laser Cut Styrene 6-Wheel Rear Truck BY Bronson-Tate Architectural Models Construction - Supplement
More informationVICTORIAN RAILWAYS GY WAGON
C/- P.O. Rhyll, Victoria, 3923. VICTORIAN RAILWAYS GY WAGON Prototype Notes The GY wagon fleet was one of the largest single classes of goods vehicle in VR service and was primarily a bulk commodities
More informationField of Armor. 1/6th SCALE TIGER 1 MODEL TANK INSTRUCTIONS
Field of Armor 1/6th SCALE TIGER 1 MODEL TANK INSTRUCTIONS Items needed for construction: - Well ventilated, clean 4' x 4' working space - 1 can black or clear ABS Glue (available in plumbing section of
More informationYou can print these instructions by downloading the PDF here: Boxcar Assembly PDF
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationPlease read and understand all instructions before building!
D-Region Tomahawk The D-Region Tomahawk kit contains all the parts necessary* to build a flying high power rocket: (1) Pre-slotted main airframe (1) Payload airframe (1) Airframe coupler tube (1) Coupler
More informationSafety Instructions, Installation & Operator's Manual For. # CLAMSHELL GRASS CA TCHER KIT For 28" & 33" REAR ENGINE RIDING MOWERS
Safety Instructions, Installation & Operator's Manual For #6-3125 CLAMSHELL GRASS CA TCHER KIT For 28" & 33" REAR ENGINE RIDING MOWERS 28" REAR ENGINE RIDER WITH CLAMSHELL BAGGER KIT SHOWN SNAPPER, McDonough,
More informationBates 1/8 scale B-26. Parts List. Instructions
Bates 1/8 scale B-26 Vacuform Pieces Swivel Ball 1 Cockpit Floor 1 Ball 2 Cockpit Back Wall 2 Two Flanges 3 Dash 3 Seven 0-64 x 1/4 Bolts 4 Dash Hood 4 Seven 0-64 Nuts 5 Center Console 6 Pilot Seat Fire
More informationMasterpiece Module Kits N T-trak Module Kit Assembly Instructions
Masterpiece Module Kits N T-trak Module Kit Assembly Instructions For tips, watch Instructional Video at http://www.youtube.com/watch?v=fklebffclau Tools Required flat, sturdy work surface Quality grade
More informationInstallation Instructions
CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationAfter the glue dries, trim the trussrod ends with your cutting pliers.
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationEnd tipping and runner wagons
End tipping and runner wagons These wagons are based on, but not identical to, those used at the "Pike Brothers Tramway", also known as the "Furzebrook Railway". Exact replicas are difficult as photographic
More informationThe Park Hotel Instructions for Assembly of N Scale Kit
The Park Hotel Instructions for Assembly of N Scale Kit Kit Contents: 198 ea. Laser Cut Acrylic Parts, 2 ea. Chimney Parts Sheets, 1 ea.2".040 styrene rod, 5 ea. Sidewalk Parts, 14 ea. Cast Resin Dormers,
More informationPlease read and understand all instructions before building!
The X-Calibur kit contains all the parts necessary* to build a flying high power rocket: (1) Pre-slotted main airframe (1) Payload airframe (1) Airframe coupler tube (1) Coupler bulkplate (1) Coupler hardware
More informationInstallation Instructions
DODGE 16K Industry Standard Rail Custom Mounting Kit #2728 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationThe Park Hotel Instructions for Assembly
The Park Hotel Instructions for Assembly Kit Contents: 280 ea. Laser Cut Acrylic Parts. 1 ea. 6" Plastic Coated Wire. 5 ea. Sidewalk Parts. 14 ea. Cast Resin Dormers. 12 ea. Window Glass Templates, 12
More informationjoining materials - wood
UNIT D E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L Wood joints joining materials - wood The majority of joints used in woodcraft have been designed specifically to attain the maximum
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2760 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationDrawings of all parts have been included for ease of part identification.
Acme Corporation Instructions for Assembly of the HO Scale Acme Corporation HO Kit Contents: 156 ea. white 1/16" laser cut acrylic part 10 ea. white 1/8" laser cut acrylic part 37 ea. adhesive-backed brick
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More information(Build Instructions)
(Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS
More informationAdditional Parts List:
THE TIME MACHINE Additional Parts List: In addition to the cast resin parts enclosed in this kit, there should also be a plastic bag containing the following items needed to complete your time machine
More informationINSTALLATION INSTRUCTIONS Stillen Front Bumper Cover P/N KA CHEVY SILVERADO
Materials supplied: 1. Front Bumper Cover 2. 14 Double-sided tape 3. (4) Screws Equipment needed: 1. Sandpaper/Schotchbrite 2. Adhesive Promoter (optional) INSTALLATION INSTRUCTIONS Stillen Front Bumper
More informationHotel Belvedere Instructions for Assembly of the HO scale kit. v1.1
Hotel Belvedere Instructions for Assembly of the HO scale kit. v1.1 Kit Contents: 319 ea. laser cut.090" acrylic parts. 132 ea. laser cut.060" acrylic parts. 8 ea. window glass templates 8 ea. window glazing
More informationthe wire, less is better. And make sure the bends on each truss wire are in line with the other. See the next photo.
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationTrack Bumpers Wood or Plastic Your Choice
Track Bumpers Wood or Plastic Your Choice An assembly method is presented to build track bumpers for non-ballasted track such as Atlas O 2st Century, Ross Custom, Gargraves etc. Whether you decide to build
More informationCHEVY/GMC SuperRail Mounting Kit #3117
CHEVY/GMC SuperRail Mounting Kit #3117 #3100 SuperGlide (12K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 12,000 lbs. 3,000 lbs. Installation Instructions SPECIFICATIONS Fits
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationDonaldson s Department Store
Donaldson s Department Store Instructions for Assembly of Donaldson s Department Store Kit Contents: 80 each laser cut acrylic parts. 1 each sheet of canopy parts. 1 each sheet of AC roof unit parts. 1
More informationMotorcycle Lift Assembly Instructions
Motorcycle Lift Assembly Instructions Copyright JCS 2009 Rev1M Page 1 Lift Table Assembly Instructions The following pages will assist you in the construction of your Motorcycle Lift Table. You will find
More informationInstructions For Corrugated End Van
Instructions For Corrugated End Van This kit contains the following items QTY ITEM QTY ITEM QTY ITEM 1 Floor 2 Van Ends 1 Roof 2 Van Sides 2 Sole Bars 4 Axle Boxes 4 Bearings 2 Coupling Hooks 2 Split Pins
More informationSpecifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive
Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive Airframe Kit (Included Contents) * Airframe Parts Sheets (Depron)
More informationTech Sheet. T4 Interior conversion kit how to - fitting instructions. 1. Rear seat belts. 2.
Page 1 of 8 T4 Interior conversion kit how to - fitting instructions Thank you for purchasing our T4 interior conversion kit. This kit will enable you to convert any SWB left hand loading door T4 into
More information968 Side Cladding Rubber Beading Replacement
968 Side Cladding Rubber Beading Replacement A common and simple wear-oriented project for the 968 is the replacement of the rubber seals or beading on the lower side body cladding. These seals become
More informationCentral New York Rocket Team Challenge 2018 Rocket Assembly Instructions
Central New York Rocket Team Challenge 2018 Rocket Assembly Instructions Note: These instructions vary from those provided by the manufacturer of the rocket kits. There is also considerable varying discussion
More informationCobra X Q Construction Tips Construction: Bel y pan
Cobra X Q Construction Tips : The white plastic in this kit is high impact styrene. It can be painted with most types of coatings if light coats are applied this is necessary due to the thickness of the
More information7mm/0Gauge BRF 025 ZUV SHARK Plough Brake. Building Instructions
Tel 07807 225801 www.prmrp.com 7mm/0Gauge BRF 025 ZUV SHARK Plough Brake Building Instructions SCALE MODEL PRODUCT FOR ADULT MODELLERS ONLY. WHITE METAL CONTAINS LEAD WASH HANDS AFTER USE. MAY CONTAIN
More informationScratch Build a Water Tower
Here s some Prototype details Photos Courtesy of Rodney Doster Water Spout and Discharge Pipe Tank Bands Here s some more Prototype details Photos Courtesy of Rodney Doster Weather Vane as a Finial Using
More informationK9 KIT INSTALLATION INSTRUCTIONS CROWN VIC KK-K9-F7-K
K9 KIT INSTALLATION INSTRUCTIONS 1998-2011 CROWN VIC KK-K9-F7-K TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric Socket Set Screwdriver Set Torx Bit
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationVACUSEAL MODEL 200. HOT TUB PRODUCTS 233 Carrington Road Bethany CT
VACUSEAL MODEL 200 J G F G H L HOT TUB PRODUCTS 233 Carrington Road Bethany CT 06524 860-469-2580 www.vacusealcoverlift.com www.hottubproducts.com Made in USA H K E D C I A P B 10 9 8 7 6 5 4 3 2 1 0 SPAS
More informationFORD #2228. Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY
FORD 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2228 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note, in
More information10. Wing prep and subassembly
Date Section Objective: Construct and fabricate the sub-assemblies of the wing panel. Required Parts: Wing left 11gal PN104-300, Wing right 1gal PN104-400, Wing left 15 gal option PN104-322, Wing right
More informationGeneral Purpose Flat Wagon
General Purpose Flat Wagon This is a freelance model of a flat wagon used by any number of railways for transporting large and awkward loads. The kit includes optional load securing rings and a pair of
More informationCabinet Mount Lifter Instructions
PART LIST 2 @ Side Pivot Arms 1 @ Coupler Tube 1 @ Left Hand Bracket 1 @ Right Hand Bracket 2 @ Cover Support Arms w/ Foam Grip 1 set of Cover Saver 4 @ 4 Wood Screw 8 @ 1 Wood Screw 12 @ 1 Black Tek Screw
More informationKossel Rev B Build Guide V1.0
Kossel Rev B Build Guide V1.0 1 Table of Contents: Step 1: BASE ASSEMBLY Gathering parts: Building the Corners and Base: Step 2: UPPER ASSEMBLY Building Upper: Step 3: VERTICAL RAIL INSTALLATION Building
More informationInstallation Instructions
CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationInstallation Instructions
DODGE RAM 2500 20K Industry Standard SuperRail Custom Mounting Kit #2336 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note,
More informationHeat up PE parts with lighter before use, brass will soften and become easy to bend and work with
Diamond T 968 was a cargo truck based on a 4 ton 6x6 chassis, powered with a Hercules RXC six-cylinder gasoline engine and equipped with a five-speed overdrive transmission and a direct and under drive
More informationVivian Mansion Assembly Instruction By Laser Dollhouse Designs
Vivian Mansion Assembly Instruction By Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also
More informationSTANDARD CANOPY WORK REPORT B-1
STANDARD CANOPY WORK REPORT B-1 No. Check Parts / Tools Qty _ Canopy Lock 1 [ ] 6E2-3 Canopy Hinge Block 1 2 [ ] 6E4-5 Canopy Side Frame 2 2 [ ] 6E2-1 Canopy Lock Assembly 1L + 1R 3 [ ] 6E2-4 Rear Lock
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationMODEL SJW - HD INSTALLATION INSTRUCTIONS
MODEL SJW - HD INSTALLATION INSTRUCTIONS CONTINUOUS ALUM. WALL FASTENER 12AF CONTINUOUS EXTRUDED ALUM. CONTINUOUS EXTRUDED ALUM. FRAME IMPORTANT INFORMATION WITH SPACER NOTE: REQUIRED WITH SJW-700HD (7"
More informationWEAR SAFETY GLASSES WHEN INSTALLING THIS KIT.
INSTALLATION INSTRUCTIONS Trans4mer Mounting Systems Part No. 29753 (black) Part No. 65654 (stainless) for full size GM pickups, and Blazer, Yukon, Suburban, Tahoe As you read these instructions, you will
More informationMold #328. Roller Bot. Nail Bot. You will need the following. pieces from mold #328 for this robot. mold #328 for this robot.
Nail Bot mold #328 for this Mold #328 Roller Bot mold #328 for this Stand the piece up and glue the tanks onto the back of the piece. Be sure to center the tanks. Lay these two pieces down on a flat surface
More informationVICTORIAN RAILWAYS QR BOGIE OPEN WAGON
C/- P.O. Rhyll, Victoria, 3923. VICTORIAN RAILWAYS QR BOGIE OPEN WAGON Prototype Notes QR number 1 was built at the VR Newport workshops in 1889, being the forerunner of a long lived and useful class of
More informationPocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.
Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =
More informationThe Saint Paul Building
The Saint Paul Building Instructions for Assembly of The Saint Paul Building. Kit Contents: 65 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk. 3 each Window Glass Templates,
More informationFord Raptor Venom Front Bumper Installation Instructions
PREPARATION 2010 2014 Ford Raptor Venom Front Bumper Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More information