INFINITY PERFORMANCE LED
|
|
- Bennett Wilkins
- 5 years ago
- Views:
Transcription
1 2016 INFINITY PERFORMNE LED PE 3 P5002 P5004 P5006 PE 4 P5014 PE 5 P5020 P5022 Drawing: XX Rev: Sheet: 1 of 10 Eng: LD Date Drawn: 07/19/17
2 TLE OF ONTENTS PE 3 (URVED) P5002, P5004, P5006 INSTRUTIONS PE 4 (STRIHT) P5014 INSTRUTIONS PE 5 (ROUND) P5020, P5022, INSTRUTIONS PE 6 IRRFT LE ND POWER ORD INSTLLTION PE 7 (P5002, P5004, P5006, P5014) FIXTURE MOUNTIN ENTERS ND DIMENSIONS (STRIHT ND URVED) PE 8 (P5020) FIXTURE MOUNTIN ENTERS ND DIMENSIONS (8 FT ROUND) PE 9 (P5022) FIXTURE MOUNTIN ENTERS ND DIMENSIONS (16 FT ROUND) PE 10 DMP LOTION WRNIN Drawing: XX Rev: Sheet: 2 of 10 Eng: LD Date Drawn: 07/19/17
3 P5002, P5004, P5006 J REF HRT H LE DJUSTERS Depending on the length of the screws supplied with the junction box (by others), you may need to use the longer screws provided. Fasten ast Swivel Plate () to junction box. For drywall ceilings, drill clearance hole for toggle bolt () per chart on center from center of junction box. For suspended ceilings, install 512 HD addy lip (by others) at location per chart on center from center of junction box and supply a 1/4-20 all thread drop through ceiling. Install griplock assembly () keeping trim washer to the ceiling side and tighten. See page 7 for mounting dimensions. While supporting the far end of fixture, lift the other fixture end and swivel ball (D) through slot (E) in the cast swivel plate and drop into center hub, aligning anti-rotation groove in swivel ball with tab in the cast swivel plate. Fasten retainer (F) to cast swivel plate with screws provided. Lift far end of fixture and push 1/16 stainless steel cable () into griplock assembly (). Level fixture by adjusting griplock assembly and other griplock postions. Make all wire connections per local and national codes. Lift canopy (H) in place and secure with screws (I) provided. Position non-supporting cable trim assembly (J) and slide o-ring (K) up to hold in place. F E D Drawing: XX Rev: Sheet: 3 of 10 Eng: LD Date Drawn: 07/19/17
4 P5014 J H REF. HRT Depending on the length of the screws supplied with the junction box (by others), you may need to use the longer screws provided. Fasten ast Swivel Plate () to junction box. For drywall ceilings, drill clearance hole for toggle bolt () per chart on center from center of junction box. For suspended ceilings, install 512 HD addy lip (by others) at location per chart on center from center of junction box and supply a 1/4-20 all thread drop through ceiling. Install griplock assembly () keeping trim washer to the ceiling side and tighten. See page 8 for mounting dimensions. While supporting the far end of fixture, lift the other fixture end and swivel ball (D) through slot (E) in the cast swivel plate and drop into center hub, aligning anti-rotation groove in swivel ball with tab in the cast swivel plate. Fasten retainer (F) to cast swivel plate with screws provided. Lift far end of fixture and push 1/16 stainless steel cable () into griplock assembly (). Level fixture by adjusting griplock assembly and other griplock postions. Make all wire connections per local and national codes. Lift canopy (H) in place and secure with screws (I) provided. Position non-supporting cable trim assembly (J) and slide o-ring (K) up to hold in place. F E D Drawing: XX Rev: Sheet: 4 of 10 Eng: LD Date Drawn: 07/19/17
5 P5020, P5022 J K REF. HRT Depending on the length of the screws supplied with the junction box (by others), you may need to use the longer screws provided. Fasten ast Swivel Plate () to junction box. For drywall ceilings, drill clearance hole for toggle bolt () per chart on center from center of junction box. For suspended ceilings, install 512 HD addy lip (by others) at location per chart on center from center of junction box and supply a 1/4-20 all thread drop through ceiling. Install griplock assembly () keeping trim washer to the ceiling side and tighten. See page 9 for mounting dimensions. While supporting the far end of fixture, lift the other fixture end and swivel ball (D) through slot (E) in the cast swivel plate and drop into center hub, aligning anti-rotation groove in swivel ball with tab in the cast swivel plate. Fasten retainer (F) to cast swivel plate with screws provided. Lift far end of fixture and push 1/16 stainless steel cable () into griplock assembly (). Level fixture by adjusting griplock assembly and other griplock postions. Make all wire connections per local and national codes. Lift canopy (H) in place and secure with screws (I) provided. Position non-supporting cable trim assembly (J) and slide o-ring (K) up to hold in place. F I H E D Drawing: XX Rev: Sheet: 5 of 10 Eng: LD Date Drawn: 07/19/17
6 IRRFT LE ND POWER ORD INSTLLTION SPLIE OX OVER SREW P SPLIE OX OVER SREW LENS LENS SPLIE OX OVER 1/4-20 STUD Remove glass lense(s) by unscrewing the lens clips at both ends of fixture and set aside. Unscrew splice box cover. Disconnect power and ground wires and cap off according to electrical standard practice. Unscrew lamplate to access Power rt able (P) connection. Remove 1/4-20 nut which secures P. If necessary remove P from the P plate by removing the #8 screw. ttach the plate to the 1/4-20 stud on the other end, then put the wires through the lamplate and reattach to the P plate. Make all electrical connections within the splice box, which already contains another set of lead wires. Reattach lamplate, splice box covers, glass lense(s), and aircraft cable at opposite end. Drawing: XX Rev: Sheet: 6 of 10 Eng: LD Date Drawn: 07/19/17
7 FIXTURE MOUNTIN ENTER ND DIMENSIONS (STRIHT ND URVED) IRRFT LE MOUNTIN ENTER POWER IN MODEL P5002 P5004 P /4" 6-7/8" 8-3/4" 62" 70" 88-1/4" 31" 35" 44-1/8" MODEL MOUNTIN ENTER P /8" Drawing: XX Rev: Sheet: 7 of 10 Eng: LD Date Drawn: 07/19/17
8 FIXTURE MOUNTIN ENTERS ND DIMENSIONS 8 FT ROUND (P5020) D E P5020 DIMENSION 62" 31" 12-3/4" D 44-9/32" E 88" Drawing: XX Rev: Sheet: 8 of 10 Eng: LD Date Drawn: 07/19/17
9 FIXTURE MOUNTIN ENTERS ND DIMENSIONS 16FT ROUND (P5022) D E P5022 DIMENSIONS 70" 35" 6-7/8" D 92" E 184" Drawing: XX Rev: Sheet: 9 of 10 Eng: LD Date Drawn: 07/19/17
10 WRNIN THIS FIXTURE IS INTENDED FOR DMP INTERIOR PPLITIONS ONLY. IT IS NOT SUITLE FOR MOUNTIN LOTIONS OUTSIDE THE ULDIN. THIS FIXTURE IS NOT DESINED TO WITHSTND OUTDOOR ONDITIONS SUH S WIND UST. INSTLLTION OF THIS FIXTURE OUTSIDE OF N ENLOSED UILDIN WILL VOID THE WRRNTY, ND MY RETE N UNSFE ONDITION. EXPOSURE TO SUSTINED WIND USTS MY USE THE FIXTURE TO FLL, RESULTIN IN SERIOUS INJURY OR DETH. Drawing: XX Rev: Sheet: 10 of 10 Eng: LD Date Drawn: 07/19/17
!When using electrical equipment, basic safety precautions should always be followed, including the following: AIR FOIL CLUSTER CP5371
AIR FOIL CLUSTER CP5371 Drawing: 762252XX Rev: B Sheet: 1 of 5 Eng: CLD Date Drawn: 01/30/17 TYPICAL FIXTURE 2-3/4" MOUNTING HOLE CENTERS ARM 700 ARM COVER CENTER PLATE STRUCTURAL MOUNTING 50-1/4" CP5371
More informationInstruction page index: Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF. Page 1 of 5. Center Feed installation Side Feed installation
Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF Page 1 of 5 Instruction page index: Center Feed installation Side Feed installation 2-3 4-5 Kilo S - Instruction for center feed installation
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationSAVE THESE INSTALLATION INSTRUCTIONS
Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT 7500003 8/4 Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT GENERAL INSTALLATION WARNING To Reduce Risk Of Death,
More informationADVANTUS CV1100 SERIES OV1100 SERIES OG1000 SERIES
CV1100 SERIES OV1100 SERIES OG1000 SERIES Drawing: 760965XX Rev: A Sheet: 1 of 5 Eng: SLN Date Drawn: 10/4/2013 8. Note: Image may vary depending on Catalog # and/or options. Illustration shows both square
More informationLCD LIFT Flat Panel Display System Installation Manual. Table of Contents
LCD LIFT Flat Panel Display System Installation Manual Table of Contents Page Installation Overview... 2 Trim Ring Installation... 3 LCD Lift Installation....4 Actuator Switch Installation.5 Top Plate
More information5 ACCESS PANEL INSTALLATION SPACER *SLIDE TO LOCATION OF FASTENER DURING INSTALLATION OF EACH FASTENER
1/2 K.O. (3/8 K.O. on 165 with factory supplied 3/8 flex conduit fitting) TR - Trim Flange Side Blocking Install Method Secure fixture to structure following instructions below: 1. Remove lens and internal
More informationINSTALLATION INSTRUCTIONS
SHD TO REMOVE HOOD (SHD) ) LOOSEN (4) SOCKET HEAD SCREWS AND RETAINING RINGS FROM HOOD (SHD). ) REMOVE HOOD AND. 3) DISCONNECT WIRES. 3 4) REMOVE REFLECTOR BY LOOSENING (4) PHILIPS HEAD SCREWS. 5) PLEASE
More informationDust RIGHT. Shop Vacuum Dust Hose Reel Instructions. For safe and effective operation, please read these instructions fully before use.
Dust RIGHT Shop Vacuum Dust Hose Reel Instructions For safe and effective operation, please read these instructions fully before use. GENERAL SAFETY WARNINGS This tool is designed for specific applications
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More informationP /8 Ring Diameter 90. Trim Ring Mounting Holes P /8. 393/16 Ring Diameter. Stud Minimum
PARTS LIST VARIABLE Top Over Head Support Bracket 1 872070 P4000-SMR Over Head Joiner Bracket 1 VARIABLE Bottom Over Head Bracket 1 79741 P4000-SMR 4 Angled Leg 4 100-00230-14 1/4-20 x 31/2 RD. HD. MS.
More informationDust RIGHT. Shop Vacuum Dust Hose Reel Instructions
Dust RIGHT Shop Vacuum Dust Hose Reel Instructions Review full instruction manual prior to use for important safety information. Always check Rockler.com to confi rm that you are using the most recent manual
More informationIMPORTANT: WILL NOT FIT COUNTRYMAN MODELS
Part #1410-0102-07 2 3 1 IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Apply masking tape around the bottom grille opening and across the bottom of the upper facto ry grille.. Open the hood and remove the
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationWARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE!
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE! General Safety Information To reduce the risk of death, personal injury or property damage from
More informationA-dec 6300 Ceiling-Mount Dental Light INSTALLATION GUIDE
A-dec 6300 Ceiling-Mount Dental Light INSTALLATION GUIDE Recommended Tools Hex key set Plumb bob Drill 3/16" drill bit 6' piece of tubing Level Phillips head screwdriver Tape measure Anti-static strap
More informationInstallation Manual Flat Track Series
Manual Flat Track Series Contents Safety...1 Parts...2 Hardware.......................................... 2 Tools Required..................................... 4.............................................
More informationSHINE CB / OW5513 CB / OW 5515 CB / OW 5517 CB / OW 5524
CB5513 / 5515 / 5517 / 5524, OW5513 / 5515 / 5517 / 5524 SHINE CB / OW5513 CB / OW 5515 CB / OW 5517 CB / OW 5524 Drawing: 762250XX Rev: B Sheet: 1 of 5 Eng: SLN Date Drawn: 10/14/15 CB5513, CB5515, CB5517
More informationBX2173 Installation Instructions Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT
BX2173 Installation Instructions 2000-04 Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT Serial No. The front fascia, coolant line bracket and anti-pollution devices are removed for baseplate
More informationWG-4 Wall Guard Installation Instructions
WG-4 Wall Guard Installation Instructions Architectural Products Division Step 1: Determine top of wall guard and snap a chalk line 1/8 below to locate top of aluminum retainer, see fig 1. Store material
More informationAssembly Instructions for model: VMPR1
Assembly Instructions for model: VMPR1 Congratulations on your purchase! The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationBX2520 Installation Instructions 2004 Mazda 3
BX2520 Installation Instructions 2004 Mazda 3 Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate installation. Drilling is required.
More informationJ-BOX. 3-O or 4-0 MUD RING J-BOX BRACKET BAR CABLE GRIPPER/ CANOPY MOUNTING STUD 8-32 BRACKET BAR SCREWS CANOPY STRAIN RELIEF POWER CORD CANOPY
KELSEY - CSS Cable Suspended Rotational and Static CSS - Cable Suspended 3-O or 4-0 MUD RING BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS STRAIN RELIEF POWER CORD MOUNTING GRIPPER AIRCRAFT CABLE CABLE
More informationINSTALLATION TORSION SPRING FRONT OR REAR MOUNT LOW HEADROOM. 1 Cutting Vertical Track. 2 Fully Adjustable Jamb Brackets
TORSION SPRING FRONT OR REAR MOUNT LOW HEADROOM Wayne Dalton, a division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH., 44660 Supplemental insert Copyright 2015 Wayne Dalton, a division of Part
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationBarn Door & Hardware Installation Guide
Barn Door & Hardware Guide INTRODUCTION Thank you for purchasing our hardware. Our barn door and hardware will add a stunning accent to your living environment and maximize its space. This manual covers
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More informationOffice Partitions WARNING. Assembly Instructions. Customer Service A S S E M B LY HARDWARE H1 H2 H3 H4 H5 H8 H9 H10 H11 H12
Customer Service 1-800-645-2986 Assembly Instructions WARNING In order to prevent structural failure, instability, t i p - o v e r, and/or serious injury, please follow i n s t ructions care f u l l y.
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 19-1/2 Attachment Tab Width: 19 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationINSTALLATION INSTRUCTIONS
STRIP DOORS AIR DOORS INSTALLATION INSTRUCTIONS BULK PVC FILM STRIP SHEET PANEL SCREENS, CURTAINS and ENCLOSURES MEGA-PRO SWINGING DOORS DOCK ACCESSORIES IMPORTANT Carefully examine the carton(s) for damage.
More informationM10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5" PH Wood Screws. (30) Included - (24) Required
Door System Unit - Hardware Tools Included: (2) 2mm Allen Wrenches, (2) 3mm Allen Wrenches, (2) 4mm Allen Wrenches, (2) 6mm Allen Wrenches, and (1) 8mm T-Handle Allen Wrench Tools Required: Phillips Screwdriver,
More informationINSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger
INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.
More informationINSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER. If there are any questions, please call (800)
INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER If there are any questions, please call (800) 255-2591 INSTALLATION INSTRUCTIONS WARNING! Ladder Sections Lock When Closed. Do Not Install or Close
More informationMounting Accessories. Installation Guide. VIVOTEK SD83XXE Speed Dome
VIVOTEK SD83XXE Speed Dome Mounting Accessories AM-116/117 Pendant Pipe AM-118 Pendant Head AM-221 Gooseneck AM-231 Parapet Mount AM-519 Pendant Adaptor Installation Guide Corresponding part numbers: AM-116:
More informationNX7 SERIES 5-1/2 HANDRAIL
STORAGE & HANDLING The handrails are shipped unassembled. Upon receipt, immediately check all material for any damage that may have occurred in transit and verify that all of the items and quantities are
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/4 Attachment Tab Width: 21-3/4 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationWARNING. BX Kia Soul Installation Instructions. Bolt Torque Specifications. Bolt Torque Specifications
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More informationHeavy Duty Ceiling Tilt Mount Installation Manual
HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part
More informationVINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS
P a g e 1 VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS Shown: 8' x 12' Vinyl Classic Pergola with 12" Top and Main Runner Spacing The design of this pergola is based on all posts being installed
More informationMSP-DCCPGTU Large Screen Tilt Display Mount
INSTALLATION INSTRUCTIONS Large Screen Tilt Display Mount The Large Screen Tilt Display Mount is a quick disconnect mounting solution for large flat panel displays. The mount features infinite adjust ability
More informationBionic 4 PERIMETER, CONTINUOUS RUN X3, X7
I NSTALLAT ION INSTRUC TIONS 6 3 /4 6 3 /4 3¾ 5 1 /2 For LP installs, ceiling opening is equal to row length + 3 /4 8 1 /2 4 3 /32 5 1 /4 Flush X7 Shown PARTS SHIPPED SEPARATELY 4 3 /32 5 1 /4 3" Regressed
More information1?4" SHEET METAL SCREW APERTURE GAUGE. Housing Aligner Spline HOUSING ALIGNER SPLINE PANHEAD SCREW. #10 x.1875 SMS. Aligner/ Seam Joiner
HOUSING ALIGNER SPL P33 INSTALLATION DRAWINGS X3 (HARD CEILING) PARTS (SHIPPED SEPARATELY) 8/32 x 1/2 PHD S.T. SCREW REMOVAL TOOL TROFFER CLAMP 1/4 Sheet Metal Screw Housing Aligner Spline HOUSING ALIGN
More informationCRITICAL INFORMATION:
IMPORTANT ALERT: GM uses a very strong thread-locking compound on all body bolts. Use of an air assisted impact ratchet can cause damage to the threads on factory body mount bolts and the internal nut
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationLow Headroom Rear Mount TorqueMaster
Low Headroom Rear Mount Supplemental Instruction Insert This supplemental installation instruction is to be used as a supplement to the main Installation Instruction and Owner s Manual provided with the
More informationBX2165 Installation Instructions Mercury Grand Marquis
BX2165 Installation Instructions 2003-06 Mercury Grand Marquis Serial No. 2003-06 Lincoln Town Car Drilling is necessary. No trimming of the fascia is needed. The BX8869 is available for this vehicle.
More informationBrooklyn Drawers Assembly Instructions
rooklyn rawers ssembly Instructions Thank you for your purchase. Please follow the instructions below for correct assembly. locking nut x30 long screw dowel bolt x16 x46 x30 F G H W Safety Strap X Wall
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2007-2010 CHEVY/GMC SILVERADO/SIERRA 2500/3500 (EXCLUDES CLASSIC) APP PART #46-23715, 40-92315/45-92310 MAX WINCH TRAY, SPORTSMAN
More information+ - 1a. 1b. c. 1d. 1e. Runway Suspended / Surface Cont. Run Installation. 2.0mm DIL DIL Revision - M 23/11/2018 Page 1
230-240V / 50-60Hz IP20 IK00 + - 2.0mm WARNING - THIS LUMINAIRE MUST BE EARTHED This luminaire has been tested and is manufactured to comply with BS EN 60598 : specification for general requirements and
More informationA500 ASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS 1 CONTENTS 2 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationMODEL T10815 GRINDING ATTACHMENTS INSTRUCTIONS
MODEL T10815 GRINDING ATTACHMENTS INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction Designed to work exclusively with the
More informationDRYWALL CEILING SPLINE KICKER REFLECTOR DIFFUSER LENGTH TABLE DIFFUSER LENGTH TABLE DESCRIPTION 2' IND 3' IND 4' IND 6' IND 8' IND
SUPPLEMENTAL INSTALLATION TYPE LG-WWD-44, R-WWD-44 & RP-WWD-44 510553-2000 WHICH IS CONTRARY TO THE CONTAINED HEREIN. P/C PG. 1 OF 1 1/4-20 THREADED ROD OR EQUAL SUPPLIED PANHEAD SHEET METAL SCREW HEX
More informationInstallation Instructions 2000/2000W/G Handrail
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions. Failure
More informationD3976 RECESSED EXIT INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationATTACH WALL PLATE TO WALL
DANGER! The Elite ar m contains high p r e s s u r e g a s s p r i n g s. T h e following cautions MUST be observed to avoid serious injury. 1. Do not attempt to adjust your Elite arm until everything
More informationInstallation Instructions
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions. Failure
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number BX2187 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationWARNING Honda Civic (Incl. EX, LX, DX) Installation Instructions BX2243. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationHeavy Duty I-Beam Trolley
Heavy Duty I-Beam Trolley ASSEMBLY INSTRUCTIONS I-BEAM TROLLEY Recommended Tools Level Tape Measure Pencil Drill with 1/8, 1/4, and 3/8, Drill Bits and Phillips Bit Socket Wrench with 9/16 Socket I-BEAM
More informationEraser Conveyor Belt Cleaning System IWARNING Always obey all applicable safety rules. Be sure all power to the conveyor has been disconnected and con
INSTALLATION GUIDE LIB-CP-REA-03-01 Rev. 10 Eraser Conveyor Belt Cleaning System ARGONICS Eraser Conveyor Belt Cleaning System IWARNING Always obey all applicable safety rules. Be sure all power to the
More information200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH
PG. 1 OF 11 PORTA-DOCK, INC. 200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH STEP 1. Separate and group like parts and fasteners together. Locate the winch side member with the longer upright tube and
More informationInstallation Instructions
Please read all instructions before installing Installation Instructions Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A B C Fixture Mounting Bracket Canopy D Threaded Standoffs (2) E Cap (2) F Anchors (4) G #10 Screws (4) H I J K Safety Cable #8 Screw Ground Screw Cupped Washer Socket Assembly (6)
More informationDYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0
DYNATRAC PRODUCTS 2007-2016 4X4 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 WARNING: Improper use or installation of this product can cause major failures
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More information!When using electrical equipment, basic safety precautions should always be followed, including the following: INSTALLATION INSTRUCTIONS
TABLE OF CONTENTS: SHEET 2: MULLION SYSTEM INSTALLATION SHEET 3: REMOTE DRIVER BOX INSTALLATION SHEET 4: 2 X 4 EXTERIOR WITH TRANSITION PLATE INSTALLATION SHEET 5: 2 X 4 INSTALLATION SHEET 6: 4 X 4 EXTERIOR
More informationcompile system INSTALLATION GUIDE Updated January 2019
INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness
More informationWARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationWARNING. BX Jeep Liberty Installation Instructions. Serial Number
Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationInstallation Type. Edge of Door. Pull (Hinge) Side Mounted. Hinge Edge of Door. Push (Stop) Side Mounted
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationPROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0
DYNATRAC PRODUCTS 2003-2010 4X4 DODGE 2500/3500 HEAVY DUTY BALL JOINT PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 WARNING: Improper use or installation of this product can cause major failures that could
More informationINSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,
INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1
More informationAssembly Instruction Item No. : HF SKU No. : Description: 48IN CHERRY CORNER FIREPLACE
ssembly Instruction Item No. : H170192 SKU No. : 810392478 Description: 48IN HRRY ORNR IRPL Option Option To prevent serious injury or death, this product is equipped with a wall anchoring system. efore
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSolar Panel Top-of-Pole Mounting Kit For Panels Over 100 Watts Including CMP Panels
Solar Panel Top-of-Pole Mounting Kit For Panels Over 100 Watts Including CMP Panels Thank you for purchasing the top-of-pole solar panel mounting kit. This mounting system is designed to enable the solar
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More information33/3547A. Special tools needed: #10-24 tap Drill bits: #25, 5/16, 13/32, 1/2
911404-00 Concealed Vertical Rod Exit Device 33/3547A Installation Instructions Devices covered by these instructions: 33/3547A and 33/3548A Concealed Vertical Rod Exit Device 33/3547A-F and 33/3548A-F
More informationMSP-DCCPGSU Large Screen Static Display Mount
INSTALLATION INSTRUCTIONS Large Screen Static Display Mount The Large Screen Static Display Mount () is a quick disconnect mounting solution for large flat panel displays. The mount self-adjusts for the
More informationHANDRAIL HEIGHT PER LOCAL CODE AUTHORITY. 6 3/8" [161.9mm]
PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION OF THIS. CONTAINED
More informationINSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 "HERITAGE" F-150/250LD 2WD, 97-04, 04 "HERITAGE" 4WD WD EXPEDITION/ WD EXPEDITION PART
INSTALLATION INSTRUCTIONS 3 BULL BAR PART #B-F1971;B-F2971 PARTS LIST: 1 Bull Bar 2 12-1.75mm x 130mm x 40mm Hex Bolts 1 Driver/Left Mounting Bracket 4 12-1.75mm x 35mm Hex Bolts 1 Passenger/Right Mounting
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More informationVersatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series
Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series TM Rough opening width (finished opening width plus 9/16") Notch for top track units (used as frame header) Rough opening height
More informationInstallation Instructions
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More information