Kongsberg Bits and Blades Catalog

Transcription

1 Kongsberg Bits and s atalog Top quality s for top quality results

2 ontents Kongsberg bits and blades Tool to blade cross reference Knife s SR6xxx (single edge round 6mm) oscillating blades mm... shaft.... blades... 6 SFxxx (single edge flat) blades SR6xxx/DR6 (single/double edge round 6mm) static cutting blades K1xx (kiss cut) blades Special purpose heavy-duty flat blades DFxxx (double-edge flat) and Rxxx (rota cut) blades Total Flute Tip Shank Single flute Up cut Acrylic SR6xxx (single edge round 6mm) foam blades Bit SR6xxx (single edge round 6mm) serrated blades SFxxx (single edge flat) foam blades SFxxx....(single....edge... flat)...serrated..... blades SFxxx... (single.... edge....flat).. standard..... blades Bits B IT-AUS mm multi purpose milling bits (up cut)... 6mm...multi... purpose..... milling.... bits...(down....cut) and 8mm super sharp milling bits (up cut) mm....super.... sharp.....milling.....bits...(down.....cut) mm soft metal single flute bits (up cut) mm....soft...metal.... single..... flute....bits...(down..... cut) mm.. wood....double....flute.. bits...(up..cut) mm wood double flute bits (down cut) 3mm multi purpose milling bits 3mm super sharp milling bits mm special purpose milling bits Accessories accessories Drawing s rease Wheels crease wheels mm crease wheels mm crease wheels mm perforation s mm crease wheels and crease blades For your personal notes ii

3 Kongsberg bits and blades Tool to blade cross reference The metals used to create our bits and blades are carefully selected to resist wear and breakage. Then, they are ground to extremely tight tolerances. Before they are shipped to you, they undergo 100% quality control to make sure you are working with the best possible s. E s L/N// s Static Knife (depends on adapter) Page 9, 10, 12, 20, 30 Static knife (Depends on adapter) Page 9, 10, 30 Hi-force knife (depends on adapter) Page 9, 10, 11, 12, 20 Knife s Static knife Double edge Page 12, 20 ibracut (depends on adapter) Rigid material knife Page 9, 10, 11, 12, 30 Esko Kongsberg offers a wide range of high quality blades, specially designed to optimize your Kongsberg Page 7 Psaligraphy knife orruspeed knife Page 14 cutting system with focus on consistent production with top quality result and a minimum of machine down Page 7 Pressut time for blade exchange. ibrating knife (depends on ) Page 16 Page 5, 9, 10, 30 Rotacut Kongsberg blades are developed, manufactured and tested by your Kongsberg team in association with Multi purpose Hi freq Knife Page 20 selected blade manufacturers. By using our blades you ensure you are on top of the production and achieve Page 5, 9, 10, 11, 30 aricut the best quality cutting and the longest blade life. Long stroke Knife Page 12, 20 Page 5 Rotacut P/ s Benefits with your Esko Kongsberg knife blades. Page 20 Kissut knife Rigid material knife Page 16 Page 7 orruspeed knife Page 7 Hi-force knife (depends on adapter) Microcut Long life Bevel knife Lowest cost pr cutting meter Top quality cutting result Page 11 -notch knife Page 9, 10, 11, 12, 20 ibrating knife (Depends on adapter) More than 100 different blades optimized for a large range of materials Short lead times (stock in all continents) Page 18 -notch (Powerhead insert) Page 5, 9, 10, 11, 30 Hi freq ibrating knife (Depends on adapter) Page 18 RB90 Knife Page 5, 9, 10, 11, 30 Page 18 Pressut rease blade adapter Page 16 Page 20 Rotacut Page 20 -notch ( Insert) Page 18 rease blade adapter Page 20 Kongsberg E 2 Kongsberg Kongsberg N Kongsberg P Kongsberg Kongsberg 3

4 Knife s *E max cutting thickness: 6mm- 1/4 SR6xxx (single edge round 6mm) oscillating blades P performance on a wide range of hard-to-cut materials. Stroke ranges from 0,3mm to 8mm and frequency ranges from 4000 to strokes pr minute. The knife blades shown in this section are designed to match the ing properties, enabling high speed and precision cutting across a wide range of materials. These are long-lasting tungsten carbide blades for maximum performance. name cutting s optimized for cutting different grades of corrugated. E Recip./MP HF knife Long stroke knife ibraut/hi Frequence ibraut knife Recip./MP HF knife Long stroke knife ibraut/hi Frequence ibraut knife Recip./MP HF knife Long stroke knife BLDSR6223 Long life tungsten carbide blade. Works well with most types of corrugated board 12mm 1/2 E* BLDSR6224 Long life tungsten carbide blade. Preferable choice for corrugated board with high recycle content. 12mm 1/2 E* top seller Our various oscillating s come with different characteristics for optimized Tool insert top seller SR6xxx (single edge round 6mm) blades for cutting with oscillating knife. L N BLDSR6242 Excellent blade for cutting tough gasket materials, even mesh armed graphite. For oscillate cutting with the High frequency knife s 8mm 5/16 E* ibraut/hi Frequence ibraut knife s optimized for cutting different heavy duty paper-based and other sandwich materials. Recip./MP HF knife ibraut/hi Frequence ibraut knife Recip./MP HF knife Long stroke knife ibraut/hi Frequence ibraut knife BLDSR6310 Provides good results on thick and rigid paper-based materials, such as triple wall corrugated and Re-board, when used with the Multi Purpose HighFrequency Knife Tool. 20mm 3/4 BLDSR6307 Offers less over-cut than the SR6310 but is more slender and may deliver a less accurate cut on curves when cutting heavy board grades 20mm 3/ top seller Long stroke knife s optimized for cutting foam board, other sandwich materials and rubber. Recip./MP HF knife corrugated dispay foam signage Long stroke knife ibraut/hi Frequence ibraut knife Recip./MP HF knife Long stroke knife ibraut/hi Frequence ibraut knife BLDSR6303 Good blade for 15 and 20mm foam board in combination with the MP Hi Frequency. 20mm 3/ BLDSR6375 Good blade for cutting die ejection rubber in combination with the Long Stroke knife 20mm 3/4 optimized for cutting soft sandwich materials. B LD -SR Diameter Round Single Edge Recip./MP HF knife Long stroke knife ibraut/hi Frequency ibraut knife Recip./MP HF knife Long stroke knife ibraut/hi Frequency ibraut knife Recip./MP HF knife Long stroke knife ibraut/hi Frequency ibraut knife BLDSR6315 A more slender tungsten carbide blade producing less overcut. Good blade for cutting materials like soft foam board. 14mm 9/16 E* BLDSR6316 Similar to the SR6315 but even thinner blade optimiced for finer details. thickness 0,3. 14mm 9/16 E* BLDSR6317 Similar to the SR6315-SR6316 but even thinner blade optimiced for the finest details. thickness 0,2 14mm 9/16 E* 5

5 Lyour bits and blades at buyn Knife s P part number name cutting These blades have a centered tip. 0 lag. BLD-DR8160 Good blade for cutting rigid materials such as different gasket materials, Forex and solid carton board. 0 lag blade 8mm shaft blades 6mm 1/ BLD-DR8180 Similar to DR8160. The blunter angle reduces the risk for breaking the blade in tough materials, but produces more overcut with thicker materials. 0 lag blade 3/16 This blade design gives the excellent performance when cutting rigid materials BLD-SR8170 Long life tungsten carbide blade for thinner flexible materials such as folding carton, polyester film, leather, vinyl, paper. 30 cutting edge 6, 1/ BLD-SR8172 Long life tungsten carbide blade for thinner flexible materials such as folding carton, polyester film, leather, vinyl, paper. 40 cutting edge 4, 3/16 such as display carton, rigid plastics, foamed P (Forex / Sintra), and several gasket materials. These blades are asymmetrically grinded with a centered tip. 0 lag. These are long-lasting tungsten carbide blades for maximum performance. Special tungsten carbide knife blade with an asymmetric edge, optimised for a nice cut ploughing all the burrs BLD-DR8261A to one side. Requires that you can control the cutting direction. Good blade for cutting different plastic materials. tip arrow grinding: 0,4-1,5 6, 1/4 NEW Special tungsten carbide knife blade with an asymmetric edge, optimised for a nice cut ploughing all the burrs BLD-DR8260A to one side. Requires that you can control the cutting direction. Good blade for cutting different plastic materials. tip arrow grinding: 0,5-1,0 6, 1/4 NEW Our range of 8mm round shaft blades are superior for cutting many different rigid Special tungsten carbide knife blade with an asymmetric edge, optimized for a nice cut pushing all the burrs BLD-DR8280A to one side. Requires that you can control the cutting direction. Good blade for cutting different plastic materials. 0 lag blade 3/ Special tungsten carbide knife blade with an asymmetric edge, optimised for a nice cut pushing all the burrs BLD-DR8210A to one side. Requires that you can control the cutting direction. Good blade for cutting different plastic materials. 0 lag blade 4mm 5/ Tungsten carbide blade for thinner flexible or rigid materials such as solid carton, vinyl, plastics. 30* cutting BLD-SR8171A angle. Asymmetric knife blade that ploughs all burrs and waste to one side. 6, 1/ Tungsten carbide blade for thinner flexible or rigid materials such as solid carton, vinyl, plastics. 40* cutting BLD-SR8173A angle. Asymmetric knife blade that ploughs all burrs and waste to one side. 4mm 5/ materials and corrugated board with the RM (Rigid Material) knife s and orruspeed both for the Kongsberg N/L// and the P/ platforms. The 8mm round stock blades come in three different shapes. The DR (double round) has a double edge and centered tip. The DR-A blades have an asymmetric, double edge. The purpose is to reduce burrs on one side of the cut, i.e. line direction control is required. The SR (single round) has a single edge, with the tip offset 4mm from the shaft center (4mm lag). hard plastic inlays ttop seller corrugated plastic BLD-SR8124 Good blade for cutting different plastic corrugated materials. Nominal lag value is 4mm 3/ BLD-SR8140 Good blade for cutting different foam core materials. Nominal lag value is 4mm 7mm 9/ BLD-SR8160 Good blade for cutting rigid substrates such as different gasket materials, Forex and solid carton board. Nominal lag value is 4mm 13mm 1/ BLD-SR8180 Similar to SR8160. The blunter angle reduces the risk for breaking the blade in tough materials, but gives more overcut with thicker materials. Nominal lag value is 4mm 8mm 5/16 BLD-SR8184 For cutting thin paper and folding carton. Works well on very fragile and porous materials such as beer coasters with a lot of recycled content. Long life tungsten carbide. Nominal lag value is 4mm 4, 3/16 B LD -DR A 6 Assymetric Diameter Round Double Edge MAY16 Kongsberg part no: These blades work with 4mm lag.. 7

6 Knife s SFxxx (single edge flat) blades P L N Tool insert E name cutting s optimized for cutting different grades of thinner materials like folding carton, paper and vinyl. SFxxx (single edge flat) blades for general purpose cutting. MP HF knife ibracut/hf ibraut Hi-force knife Static knife MP HF knife Static knife single edge ibracut/hf ibraut Hi-force knife Static knife Reciprocating knife Static knife F Reciprocating knife Static knife F Static knife single edge ibracut/hf ibraut Hi-force knife Static knife ariut knife BLDSF216 (i-216) Single-edge blade for soft flexible materials. Used to through-cut paper, vinyl, etc 2-3mm BLDSF217 (i-217) Single-edge blade for soft flexible materials. Used to through-cut paper, vinyl, etc. The more pointed edge reduces overcuts 2-3mm BLDSF238 For folding carton and other high-precision applications with long lifetime requirement. Tungsten carbide steel with precision ground and polished edge, which handles softer, abrasive materials very well BLDSF224 For folding carton and other high-precision applications with long lifetime requirement.. Tungsten carbide steel with precision ground and polished edge. The top part of the tip is grounded off, to prevent snapping BLDSF230 (i-230) Mat cutting, frame cutting, passpartout and more. This is a single edge design. 2mm 5/64 Flat Single Edge solid board box top seller flexo plates gaskets Static knife single edge top seller thin carton tabletop display B LD -SF

7 Knife s P L N E Tool insert Static knife single edge ibracut/hf ibraut Hi-force knife Static knife ariut knife name BLDSF231 (i-231) Mat cutting, frame cutting, passpartout w/ small radius and more. This is a single edge design with a flat tip. cutting P 2mm 5/64 L N E Tool insert name MP HF knife BLDSF426 (i-426) ard stock, rubber and more. This is an oscillate knife with a 10 /25 cut angle, a single edge design, flat tip 6mm ¼ MP HF knife ibracut/hf ibraut BLDSF427 (i-427) cutting textiles, fabrics, fibrous tissues. This is an oscillate knife with a 10 /25 cut angle, a single edge design, flat tip. 3/8 Hi-force knife single edge MP HF knife ibracut/hf ibraut Static knife ariut knife BLDSF233 (i-233) Mat cutting, frame cutting, passpartout w/ small radius and more. This is a asymmetric single edge design with a flat tip..19 MP HF knife BLDSF428 (i-428) orr ugated stock, foam board. This is an oscillate knife with a 4 /45 cut angle, a single edge design, flat tip. 23mm BLDSF429 (i-429) Soft Materials, foam board and more. This is an oscillate knife with a 3.5 /45 cut angle, a single edge design. 29mm 1.10 s for cutting in 45 degrees angle with the Bevel knife s optimized for cutting corrugated board with high recycled content; can also perform well in foam board. Reciprocating knife Reciprocating knife BLDSF115 Special knife blade for Recycled Board Knife Tool. Made of high speed steel BLDSF125 For corrugated board up to and including TW. Precision ground edge. Made of high speed steel, which will last longer than conventional steel. Used by customers who need to cut corrugated with high recycle content, or those wanting longer blade lifetime Static knife TW mm 1/2 Bevel knife BLDSF212 A special tungsten carbide knife blade design that has been developed for optimal performance in flexo plate materials 7mm 9/ BLDSF245 A special tungsten carbide knife blade for cutting -notch folding lines in solid board carton 6mm 1/ mm 5/8 s for static cutting of gaskets and other highly abrasive materials BLDSF310 Specially designed blades for gasket cutting, but may be useful for other applications such as corrugated samplemaking. 3/ BLDSF320 Specially designed T blades for gasket cutting, but may be useful for other applications such as corrugated samplemaking. 3/ BLDSF311 The blade is well suited for cutting highly abrasive materials that are not very hard 7mm 9/ BLDSF321 The blade is well suited for cutting highly abrasive materials that are not very hard 7mm 9/32 s for cutting rubber and similar materials MP HF knife Hi-force knife MP HF knife Hi-force knife MP HF knife ibracut/hf ibraut Hi-force knife MP HF knife ibracut/hf ibraut ibracut/hf ibraut s for cutting rubber and similar materials s optimized for cutting different grades of thinner materials like folding carton, paper and vinyl. Static knife cutting Static knife BLDSF420 (i-420) BLDSF421 (i-421) Tungsten carbide steel, precision ground edge. For high performance and long lifetime in rubber materials orrugated stock, foam board and more. for oscillate knife with a 5 /25 cut angle, a single edge design 3/8 gasket s optimized for cutting gasket materials with the MP HF knife 3/8 BLDSF422 (i-422) orrugated stock, foam board and more. for oscillate knife with a 10 /25 cut angle, a single edge design 3/8 BLDSF425 (i-425) ard stock, rubber and more. This is an oscillate knife with a 10 /25 cut angle, a single edge design, flat tip 6mm ¼ MP HF knife HF ibraut MP HF knife HF ibraut BLDSF312 For Gasket, Highly abrasive materials, not really hard T. PM10 Extreme Wear Tool Steel (EWTS) is 25x tougher than -Acto and more flexibel than T. Angle 30 degrees 7mm 9/ BLDSF313 For Gasket, Highly abrasive materials, not really hard T. PM10 Extreme Wear Tool Steel (EWTS) is 25x tougher than -Acto and more flexibel than T. Angle 45 degrees 7mm 9/ s for cutting foam core board materials Static knife double edge BLDSF246 (i-246) core board blade for double- edge insert 3/8 11

8 Knife s SR6xxx/DR6 (single/double edge round 6mm) static cutting blades P L N E Tool insert name BLDSF346 (i-346) cutting SR6xxx / DR6 (single/double edge round 6mm) blades for static cutting with the Hi-Force Static knife double edge Soft and rigid foam blade for double- edge insert with 45 edge. 3/8 knife, Static knife and Psaligraphy knife. These are long lasting tungsten carbide blades for maximum performance. The 6mm round stock blades come in three different shapes, all with a centered tip. The SR (single round) has a single edge. The DR (double round) has a double edge and centered tip. The DR-A blades have an asymmetric double edge. The purpose is to reduce burrs on one side of the cut (i.e., line direction control is required). thin plastic cards Diameter Round Single Edge folding carton package B LD -SR

9 Knife s * This new can take all the knife blades in this category. P L N E Tool insert part number name cutting K1xx (kiss cut) blades s optimized for cutting different thinner flexible materials Hi-Force Knife BLDSR6150 Long life tungsten carbide blade for thinner flexible materials such as folding carton, polyester film, leather, vinyl, paper. 30* cutting angle. 3/16" BLDSR6152 Long life tungsten carbide blade for thinner flexible materials such as folding carton, polyester film, leather, vinyl, paper. 40* cutting angle. 3/16" BLDSR6151 Long life tungsten carbide blade for thinner flexible materials such as folding carton, polyester film, leather, vinyl, paper. 22* cutting angle 3/16 ariut Knife Static Knife Psaligraphy Knife * Hi-Force Knife K1xx (kiss cut) blades for cutting various thin materials like adhesive foils, paper etc. The blades are kept in the body with a friction lock. ariut Knife Static Knife Psaligraphy Knife * Static Knife ariut Knife Hi-Force Knife Psaligraphy Knife * s optimized for cutting different thinner flexible or rigid materials Hi-Force Knife adhesive vinyl decals BLDDR BLDDR6161 Tungsten carbide blade for thinner flexible or rigid materials such as solid carton, vinyl, plastics. 2x40* cutting angle. Spear-headed shape. ariut Knife Static Knife Psaligraphy Knife * Hi-Force Knife ariut Knife Static Knife Psaligraphy Knife * 3/16 3mm 1/8 reflective vinyl roll Top seller Tungsten carbide blade for thinner flexible or rigid materials such as solid carton, vinyl, plastics. 2x30* cutting angle. Spear-headed shape BLDDR6169A Tungsten carbide blade for thinner flexible or rigid materials such as solid carton, vinyl, plastics. 2x40* cutting angle. Spear-headed shape. Asymmetric knife blade that pushes all burrs and waste to one side. 3mm 1/ Tungsten carbide blade for thinner flexible or rigid materials such as BLDsolid carton, vinyl, plastics. 40* cutting SR6159A angle. Asymmetric knife blade that ploughs all burrs s and waste to one side. 3mm 1/8 ariut Knife Static Knife Psaligraphy Knife * Hi-Force Knife ariut Knife Static Knife Psaligraphy Knife * Kiss ut Hi-Force Knife Asymmetric knife blade that pushes all burrs and waste to one side for thinner flexible or rigid materials B LD -K

10 Knife s P L N x Special purpose heavy-duty flat blades E Tool insert/unit name cutting s optimized for kiss cutting various thinner flexible materials Special purpose heavy-duty flat blades, TZ1xx, TZ5xx, (Trapezoid), DF5, (double flat), BLD-K101 (i-101) BLD-K102 (i-102) Sharper-edged blade for thicker, tougher adhesive foils, such as reflex foil BLD-K103 (i-103) BLD-K104 (i-104) A sharper general purpose kiss-cutting blade for fine details in adhesive foils, Its properties allow secure separation of foil and adhesive, to facilitate weeding BLD-K105 (i-105) Rubber, ardboard, diamond grade and more. This is a vinyl Knife, with a 20 /55 cut angle, a single edge design.and adhesive, to facilitate weeding 1mm 1/25" BLD-K154 (i-154) Thicker vinyl, diamond grade, carton, polyester fabric and more. This is a vinyl knife with a 30 /30 cut angle, a single edge, long design and adhesive, to facilitate weeding 1mm 1/25" Kiss ut knife 1mm 1/25" 1mm 1/25" SF29x (single flat) top seller General purpose kiss-cutting blade for standard thickness adhesive foils. Its properties allow secure separation of foil and adhesive, to facilitate weeding Pressut Pressut Kiss ut knife Pressut Kiss ut knife Pressut Kiss ut knife Masking Film. This is a vinyl knife with a 40 /35 cut angle, a double edge design. 1mm 1/25" 1mm 1/25" Pressut Kiss ut knife Pressut Kiss ut knife Re-board display Trapezoid Re-board sheet with v-notch B LD -TZ

11 Knife s P L N Tool insert name cutting Tungsten carbide blades optimized for long-life -notch cutting tough paper-based materials like Re-board, triple wall corrugated, etc BLDTZ511 ery good blade for -notch cutting through materials such as Re-board, -board and triple wall corrugated. uts materials up to about 17mm. Made from a special tungsten carbide alloy, to extend cutting cycles. Thickness 0.6mm mm 43/64 BLDTZ512 ery good blade for -notch and straight cutting with the HD-knife through materials such as Re-board, -board and triple wall corrugated. uts materials up to about 17mm. Made from a special tungsten carbide alloy, to extend lifetime. Thickness 0,9mm,035" 17mm 43/64 Power -Notch holder HD unit Power HD unit -Notch holder / HD knife P L N L N Tool insert All insert positions on N / L / heads I Notch insert name BLDDF572 Specially made double angle arrow shaped, blade for the I notch insert. Have superb performance in materials like Kappa and other foamed core board. Works also well in materials such as fluted core boards and triple wall corrugated. Made from a special Tungsten arbide alloy, to extend lifetime. Thickness 0.6mm cutting 16mm 5/8 Tungsten carbide blades optimized for long-life high speed straight cutting tough paper-based materials like Re-board, triple wall corrugated, etc. L N All insert positions on N / L / heads RB90 insert BLDSF290 Specially made blade for the RB90-16 insert. Works well in materials such as fluted core boards and triple wall corrugated. Made from a special tungsten carbide alloy, to extend lifetime. Thickness 0.9mm mm 5/8 Standard blades for cutting tough paper-based materials like Re-board, triple wall corrugated, etc. BLDTZ129 Super-trapezoid, deep-edged blade, used with the -notch knife and the HD-knife. This blade is thicker and stiffer than standard trapezoid blades and will give a more accurate cut. Thickness 0.9mm mm 43/64 BLDTZ192 Super-trapezoid, deep-edged blade, used with the -notch knife and the HD-knife. This blade is thinner than the TZ129 blade and will give very good result in fluted core board. Thickness 0.6mm mm 43/64 Power -Notch holder HD unit Power HD unit -Notch holder / HD knife Tungsten carbide blades optimized for long-life high-speed straight cutting tough paper-based materials like Re-board, triple wall corrugated, etc Power HD knife BLDTZ230 HD unit Special trapezoid blade for the HD30 knife, designed for Re-board and similar material in thickness up to and including 30mm Tungsten carbide steel material with precision ground edge 30mm 13/16 Tungsten carbide blades optimized for long-life -notch cutting tough paper-based materials like Reboard, triple wall corrugated, etc., for use in the I45 insert. 18 L N All insert positions on N / L / heads I Notch insert L N All insert positions on N / L / heads I Notch insert BLDDF570 Specially made arrow-shaped blade for the I notch insert. Works well in materials such as fluted core boards and triple wall corrugated. Made from a special Tungsten arbide alloy, to extend lifetime. Thickness 0.9mm mm 5/8 BLDDF571 Specially made arrow shaped, blade for the I notch insert. Works well in materials such as fluted core boards and triple wall corrugated. Made from a special Tungsten arbide alloy, to extend lifetime. Thickness 0.6mm mm 5/8 19

12 Knife s DFxxx (double-edge flat) and Rxxx (rota cut) blades P L N E Tool insert name cutting Double-edge blades with a centered tip. Have grinded edge on both Double-edge flat blades with a centered tip for cutting hard, thinner materials. R blade Static knife double for cutting textile materials with the Rotaut s. These are long lasting tungsten carbide blades for maximum performance. Heavy duty Insert for Power / HD unit Static knife double Heavy duty Insert for Power / HD unit BLD-DF212 (i-312) General-purpose, double-sided, 80º sword knife blade for flexible materials. Used for throughcutting paper, cardboard, vinyl, thin plastics, styrene, etc BLD-DF213 (i-313) General-purpose, double-sided, 60º sword knife blade for flexible materials. Used for throughcutting paper, cardboard, vinyl, thin plastics, styrene, etc /16 3/16 Half- double-edge blades with a centered tip. Hi-Force knife Static knife BLD-DF112 (i-308) General-purpose, double-sided, 80º sword knife blade for flexible materials. Used for throughcutting paper, cardboard, vinyl, thin plastics, styrene, etc 3/16 BLD-DF113 (i-309) General-purpose, double-sided, 60º sword knife blade for flexible materials. Used for throughcutting paper, cardboard, vinyl, thin plastics, styrene, etc. 3/16 ariut Hi-Force knife Static knife paper invitations contour cut textile display ariut Ten-facetted rotating knife blade for cutting textiles Rotaut for L/ N/ blade fits directly in BLD-R110 1, 1/16 Flat Double Edge Rotaut for E/ P/ R10 Decagonal knife blade with a 2. For use on textile materials with the Rotaut B LD -DF

13 Knife s SR6xxx (single edge round 6mm) foam blades L P tn Tool insert name cutting s for cutting different grades of foam materials up to maximum 30mm -1 ¼ thickness These are long lasting tungsten carbide blades for maximum performance Knife cutting performance determined by matching knife blade design and BLD-SR6311 for max. 30mm material thickness. 2.5 cutting angle enables very fine details with little over-cut in foam qualities with good cutting properties. Pointed tip for use with felt underlays BLD-SR6312 for max. 30mm material thickness. 6 cutting angle enables fine details in a variety of foam materials. Pointed tip for use with felt underlays 32mm 1 1/ for max. 30mm material thickness. 8 cutting angle enables fine details in a wider range of foam BLD-SR6313 qualities, as well as 30mm Re-board. Flattened tip helps increase cutting speed and protect P cutting underlays 32mm 1 1/ properties such as oscillation frequency and stroke. With N and L tables, Knife the foam ing requires high (9) traverse clearance. The pointed blades often provide the best detail accuracy. With the pointed blades it is possible to increase 32mm 1 1/ cutting speed by using the 5, felt cutting underlay. Knife Top seller s for cutting different grades of foam materials up to maximum 5-2 1/8 thickness BLD-SR6521 for max. 5 material thickness. 2.5 cutting angle enables very fine details with little over-cut in foam qualities with good cutting properties. Pointed tip for use with felt underlays BLD-SR6522 for max. 5 material thickness. 3.7 cutting angle enables fine cutting details. Pointed tip for use with felt underlays 5 2 1/ for max. 5 material thickness. 3.7 cutting angle enables fine cutting details. Flattened BLD-SR6523 tip to increase cutting speed and protect P cutting underlays 5 2 1/8 dense foam printed sign protective packaging /8" s for cutting different grades of foam materials up to maximum 80mm -3 1/8 thickness BLD-SR cutting angle enables very fine cutting details, minimal overcut and largely eliminates conical holes. Pointed tip for use with felt underlays 80mm 3 1/8 BLD-SR cutting angle enables very fine cutting details, minimal overcut and largely eliminates conical holes. Flattened tip to increase cutting speed and protect P cutting underlays 80mm 3 1/8 Diameter Round Single Edge B LD -SR

14 Knife s SR6xxx (single edge round 6mm) serrated blades P L N SR6xxx (single edge round 6mm) serrated blades for cutting different qualities and thicknesses of honeycomb and papercore board materials. Also good for some dense Tool insert name cutting s for cutting different grades of tough paper materials up to maximum 30mm -1 ¼ thickness Knife foam materials regards to stroke amplitude and frequency. For the L and N, these s require high Knife achieve better productivity with the 5, felt cutting underlay. 32mm 1 1/ The serrated edge cuts with less friction between blade and material than a smooth BLD-SR6352 edge. Thus, the blade gets less hot. Thickness 1 mm - 1/25", flattened tip to increase cutting speed and protect P cutting underlays 32mm 1 1/ The serrated cuts with gives less friction between blade and material than a smooth BLD-SR6353 edge. Thus, the blade gets less hot. Thickness 1,5 mm -,006", pointed edge for use with felt underlay. 32mm 1 1/ The serrated edge cuts with less friction between blade and material than a smooth edge. Thus, the blade gets less hot. Thickness BLD-SR6354 1,5 mm -,006", flattened tip to increase cutting speed and protect P cutting underlays 32mm 1 1/ Our oscillating foam cutting s are optimized to work with these knife blades with (9) traverse clearance. When working with these s and blades, you can often The serrated edge cuts with less friction between blade and material than a smooth BLD-SR6351 edge. Thus, the blade gets less hot. Thickness 1 mm - 1/25", pointed edge for use with felt underlay. These are long lasting tungsten carbide blades for maximum performance. Knife Knife s for cutting different grades of paper sandwich materials up to maximum 5-2 1/8 thickness The serrated edge cuts with less friction between blade and material than a smooth BLD-SR6551 edge. Thus, the blade gets less hot. Thickness 1 mm - 1/25", pointed edge for use with felt underlays / The serrated edge cuts with less friction between blade and material than a smooth BLD-SR6552 edge. Thus, the blade gets less hot. Thickness 1,5 mm -.006", pointed tip for use with felt underlays / The serrated edge cuts with less friction between blade and material than a smooth BLD-SR6553 edge. Thus, the blade gets less hot. Thickness 1 mm - 1/25", flattened tip to increase cutting speed and protect P cutting underlays / thick Re-board honeycomb signs Diameter Round Single Edge B LD -SR

15 Knife s SFxxx (single edge flat) foam blades P L N Tool insert name cutting s for cutting different grades of foam materials up to maximum 40mm -1 ¼ thickness SFxxx (single edge flat) blades for cutting foam material of different grades and Knife thicknesses. These blades are made of HSS steel, which means it is less expensive and also offers less tendency to snag compared to tungsten carbide BLDSF501 Excellent general purpose foam knife - very sharp and durable 40mm 1 9/16" BLDSF502 This blade has the same advantages as SF501. The greater sloping edge allows for a slightly faster feed rate and improves cutting ability in softer materials. However, it will have a negative influence on quality effect with narrow curves 40mm 1 9/16" Our oscillating foam cutting s are optimized to work with these knife blades with regards to stroke amplitude and frequency. For the L and N these s require the Knife high (9) traverse clearance. When working with these s and blades, you can s for cutting different grades of foam materials up to maximum 60mm -2 3/8 thickness often achieve better productivity with the 5, felt cutting underlay BLDSF BLDSF506 Excellent general-purpose knife - very sharp and durable 60mm 2 3/ This blade has the same advantages as SF505. The greater sloping edge allows for a slightly faster feed rate but will have a negative quality effect with narrow curves 60mm 2 3/8 s for cutting different grades of foam materials up to maximum 86mm -3 3/8 thickness protective packaging BLDSF509 Specialty blade for the. Excellent general-purpose foam knife - very sharp and durable. uts up to 86mm [3 3/8 ] thick material 86mm 3 3/8 BLDSF510 Excellent general-purpose foam knife - very sharp and durable. The greater sloping edge allows for a slightly faster feed rate and may improve cutting ability in some softer materials. However, its edge angle will have negative quality effect with narrow curves. 86mm 3 3/8 Diameter Flat Single Edge dense foam sign letters B LD -SF

16 Knife s SFxxx (single edge flat) serrated blades P L N x Tool insert name cutting s for cutting different grades tough paper materials up to maximum 40mm -1 9/16 thickness SFxxx (single edge flat) serrated blades for cutting different qualities and thicknesses of Knife honeycomb and papercore board materials. Also good for some dense foam materials BLDSF503 Designed for cutting paper honeycomb material. Suitable also for some dense foam materials, which are vulnerable to melting. The serrated edge cuts with less friction between blade and material than a smooth edge. Thus, the blade gets less hot BLDSF504 This blade has the same advantages as SF503. The greater sloping edge allows for a slightly faster feed rate and may improve cutting ability in softer materials, but will have a slightly negative quality effect with narrow curves Our oscillating foam cutting s are optimized to work with these knife blades with regards to stroke amplitude and frequency. For the N and L these s require the Knife high (9) traverse clearance. When working with these s and blades, you can often achieve better productivity with the 5, felt cutting underlay These blades are made of HSS steel, which means a lower price and less tendency to 40mm 1 9/16 40mm 1 9/16 s for cutting different grades of paper sandwich materials up to maximum 60mm -2 3/8 thickness snag compared to tungsten carbide. BLDSF507 Designed for cutting paper honeycomb material. Suitable also for some dense foam materials that are vulnerable to melting. The serrated edge cuts with less friction between blade and material than a smooth edge. Thus, the blade gets less hot. 60mm 2 3/8 BLDSF508 This blade has the same advantages as SF507. The greater sloping edge allows for a slightly faster feed rate and may improve cutting ability in softer materials but will have a slightly negative quality effect with narrow curves 60mm 2 3/ s for cutting different grades of tough paper materials up to maximum 86mm -3 3/8 thickness BLDSF511 Honeycomb and foam knife with serrated edge. ery sharp and durable. uts up to 86mm [3 3/8"] thick material 86mm 3 3/ BLDSF512 Honeycomb and foam knife with serrated edge. ery sharp and durable. uts up to 86mm [3 3/8 ] thick material 86mm 3 3/ BLDSF513 Honeycomb and foam knife with serrated edge. ery sharp and durable. uts up to 86mm [3 3/8 ] thick material 86mm 3 3/8 Re-board furniture Flat Single Edge Re-board point of purchase display B LD -SF

17 Knife s SFxxx (single edge flat) standard blades P L N E Tool insert/unit name cutting Standard low-cost blades for samplemaking with different materials. SFxx (single edge flat) standard blades for cutting in different materials. Static knife TW paper beer coasters Static knife F Reciprocating knife Static knife F ibracut / HF ibraut Static knife F BLD-SF102 Knife for triple wall samplemaking. BLD-SF172 The furthest part of the tip is ground off to avoid snapping. Preferred by customers for folding cartons, Equivalent to SF186, but slightly shorter. BLD-SF186 Used for corrugated samplemaking. NOT suitable for production runs since tip is very brittle and blade is subject to flexing BLD-SF110 Good choice for folding carton. More durable than the ASR and cuts with less plow effect in the cut edges. Also suitable for varnish blankets with the Microut Tool BLD-SF177 Used by many customers for F samplemaking. Produces a nice cut in thin carton. Tip will last long, due to edge angle. an also be used for chipboard. Good choice for cutting varnish blankets ery rigid and will bend less than most other standard carbon steel blades.good standard blade for folding carton, and other thin,compact materials such as polycarbonate and other synthetics. Static knife BLD-SF184 Static knife single edge BLD-SF210 (i-210) 6mm 1/4 HSS Flat knife, 40 degree cut angle, single edge design Flat Single Edge folding carton package Static knife F B LD -SF

18 Bits When handling and storing milling bits, always treat them with great care. The bits are manufactured from 6mm multi purpose milling bits (up cut) tungsten carbide, and the sharp edges are very easily chipped and degraded if they get in touch with any hard surface. To achieve maximum milling precision, always try to adjust the depth of cut as close as possible to the Our 6mm multi purpose milling bits come in a large range of tip s and thickness of the material when selecting a milling bit for a certain job. spiral s. See chart for more details on milling, milling thickness and recomended RPM. When cutting material is significantly thicker than the cutting, the best approach is to set the milling lines as multi-pass operations; executing each shape multiple times, digging gradually deeper into the material. As a general rule, the depth of each pass should not exceed times the of the cutting. There will, however, be materials where either a smaller or larger depth step is appropriate. For milling jobs, it is recommended to program feed rates in absolute values (i.e., m/min or ips; not as a percentage of maximum speed). Most applications are best finished using up cut bits due to better chip removal performance. If you encounter print chipping or lamination separation/damage, use a down cut bit to achieve the best top Total Flute Tip contour cut pvc Shank Single flute Multi Purpose Bit Up ut back printed acrylic finish. A down-cut bit can also be beneficial in cases where there is a problem holding down the material. B IT-MUS

19 Bits * max RPM = 45 6mm Up ut Bit 6mm Up ut Bit oated 6mm Up ut Bit Double Flute = 1kW = 3kW MultiUT Ibag = 1kW MultiUT = 1kW max RPM 45 MultiUT Kavo = 1kW MultiUT HP = 3kW P N/L starter ollets milling RPM BITMUS (i-3854) 3/16" BITMUS /16" BITMUS /16" BITMUS (i-3816 i-3862 i-3866) BITMUS /8" BITMUS mm 1/2" /8" BITMUS /16" 3/8" BITMUS (i-3824 i-3874) 20mm 13/16 BITMUS /8" BITMUS mm 13/ BITMUS (i-3880) 20mm 13/ BITMUS (i-5854) 3/8" BITMUS (i-3888) 20mm 13/ BIT-MUS single flute, coated. Special variety of multi purpose milling bit, coated for better performance with different materials like aluminum and AM. 3/16" BIT-MUS single flute, coated. Special variety of multi purpose milling bit, coated for better performance with different materials like aluminum and AM. 3/16" BIT-MUS single flute, coated. Special variety of multi purpose milling bit, coated for better performance with different materials like aluminum and AM. 3/8" BITMUD (i-2624) double flute bit. 14mm 9/16" BITMUD (i-2626) double flute bit. 23mm 7/8" /16" BIT-MUS single flute, coated. Special variety of multi purpose milling bit, coated for better performance with different materials like aluminum and AM. 30mm 1 3/ RPM BITMUS (i-3889) 34 BITMUS milling Top seller Bit name Bit ollets P Top seller Bit name starter Top seller Bit N/L

20 Bits * max RPM = 45 6mm multi purpose milling bits (down cut) Up ut Bit Down ut bit = 1kW = 3kW MultiUT Ibag = 1kW MultiUT = 1kW, max RPM = 45 MultiUT Kavo = 1kW MultiUT HP = 3kW Our 6mm multi purpose milling bits come in a large range of tip s and spiral s. See chart for more details on milling, milling thickness P andrecomended RPM. N/L/ starter plastic standing display MultiUT BITMDS (i-2854) Multi purpose, downcut, 3mm 1/8" BITMDS Multi purpose, downcut, 3/16" BITMDS (i-2862 i-2866) Multi purpose, downcut, 3/8" BITMDS Multi purpose, downcut, 7mm 9/32" BITMDS (i-2804) Multi purpose, downcut, 7mm 9/32" BITMDS (i-2874) Multi purpose, downcut, 3/8" BITMDS (i-2880) Multi purpose, downcut, 20mm 13/16" BITMDS (i-2888) Sintra, Styrene, Acrylic, Polycarbonate, Dibond, with top print/ laminate 20mm 13/16 BITMDS (i-2889) Routing for soft/hard plastic Sintra, Styrene, Acrylic, Di-bond, i.e. w/ top print/laminated 30mm 1 3/ Total Flute Tip Shank Single flute Down ut Multi Purpose Bit RPM milling Bit name Bit ollets B IT-MDS

21 Bits * max RPM = 45 6 and 8mm super sharp milling bits (up cut) 6mm Up ut Bit 8mm Up ut Bit = 1kW = 3kW MultiUT Ibag = 1kW MultiUT = 1kW max RPM 45 MultiUT Kavo = 1kW MultiUT HP = 3kW Our 6mm super sharp milling bits come in a large range of tip s and spiral s. See chart for more details on milling, milling thickness and P recommended RPM. The Super Sharp bits are grinded / polished for an optimized acrylic acrylic Total Flute Tip Shank Single flute Up ut Acrylic Bit BITAUS /16" BITAUS /16" BITAUS /8" BITAUS mm 1/2" BITAUS mm 13/ BITAUS mm 9/32" BITAUS /8" BITAUS mm 13/ BITAUS mm 3/8" BITAUS mm 13/16 BITAUS mm 3/8" Top seller RPM milling Bit name Top seller Bit ollets routing surface. N/L/ Starter B IT-AUS

22 Bits ollets Bit Bit name milling BITAUS mm 13/ BITAUS mm 1 1/8" RPM 40 Our 6mm super sharp milling bits come in a large range of tip s and spiral s. See chart for more details on milling, milling thickness and recomended RPM. The Super Sharp bits are grinded / polished for an optimized routing 40 surface BITAUS mm 1 1/2" BITAUS mm 2" 30 Tip acrylic Shank Single flute Down ut Acrylic Bit polystyrene core sign Total N/L/ Top seller P 6mm super sharp milling bits (down cut) Flute Starter B IT-ADS

23 Bits * max RPM = 45 Up ut Bit Down ut bit = 1kW = 3kW MultiUT Ibag = 1kW MultiUT = 1kW max RPM 45 MultiUT Kavo = 1kW MultiUT HP = 3kW BITADS down-cut, single flute bit. 3/ BITADS down-cut, single flute bit. 3/16" BITADS down-cut, single flute bit. 3/8 AM aluminum sign letters BITADS down-cut, single flute bit. 7mm 9/ BITADS down-cut, single flute bit. 11mm 3/8 BITADS down-cut, single flute bit. RPM. chart for more details on milling, milling thickness and recommended 6mm multi purpose bits are ideal for milling soft metals such as aluminum. See RPM mm 13/16 40 Total milling Bit Flute Bit name Tip Bit Shank ollets Single flute N/L/ Up ut P Soft Metals Starter 6mm soft metal single flute bits (up cut) B IT-SUS

24 Bits Up ut Bit Down ut bit = 1kW = 3kW * max RPM = 45 6mm soft metal single flute bits (down cut) MultiUT Ibag = 1kW MultiUT = 1kW max RPM 45 MultiUT Kavo = 1kW MultiUT HP = 3kW 44 Aluminum, hard laminate with top print/laminate or blank 12mm 15/ BITSUS (i-3924) Aluminum, hard laminate with top print/laminate or blank 20mm 13/ BITSUS (i-3930) Aluminum, hard laminate with top print/laminate or blank 16mm 3/8 BIT-MUS single flute, coated. Special variety of multi purpose milling bit, coated for better performance with different materials like aluminum and AM. 3/16" BIT-MUS single flute, coated. Special variety of multi purpose milling bit, coated for better performance with different materials like aluminum and AM. 3/16" BIT-MUS single flute, coated. Special variety of multi purpose milling bit, coated for better performance with different materials like aluminum and AM. 3/16" BIT-MUS single flute, coated. Special variety of multi purpose milling bit, coated for better performance with different materials like aluminum and AM. 3/ BITSUS (i-3916) more details on milling, milling thickness and recommended RPM printed AM AM Sign Total 6mm multi purpose bits are ideal for milling soft metals such as aluminum. See chart for RPM Flute milling Top seller Tip Bit name Shank Bit Single flute ollets Down ut N/L/ Soft Metals P Bit starter B IT-SDS

25 Bits Up ut Bit Down ut bit = 1kW = 3kW * max RPM = 45 6mm wood double flute bits (up cut) MultiUT Ibag = 1kW MultiUT = 1kW max RPM 45 MultiUT Kavo = 1kW MultiUT HP = 3kW P N/L / Starter ollets RPM Aluminum, hard laminate with top print/laminate 12mm 15/32 BITSDS (i-2924) Aluminum, hard laminate with top print/laminate 20mm 13/16 BITSDS (i-2930) Aluminum, hard laminate with top print/laminate 16mm 5/8 Bit name BITSDS (i-2916) mm multi purpose bits are ideal for milling wood and wood composite materials. See chart for more details on milling, milling thickness and recommended RPM. milling Bit 50 wood signs wood composite Up ut Bit Down ut bit = 1kW = 3kW * max RPM = Soft hard composite wood with top print laminate. 2 1 BITWUD (i-5210) BITWUD (i-5212) 16mm 5/ Soft hard composite wood with top print laminate Double flute Bit Wood RPM Bit name 50 Total milling Bit Flute ollets Tip N/L/ Shank P Starter Up ut MultiUT Ibag = 1kW MultiUT = 1kW max RPM 45 MultiUT Kavo = 1kW MultiUT HP = 3kW B IT-WUD

26 Bits 6mm wood double flute bits (down cut) 3mm multi purpose milling bits 6mm multi purpose bits are ideal for milling wood and wood composite materials. See 3mm multi purpose bits are ideal for milling many small details and inside radiuses in chart for more details on milling, milling thickness and recommended RPM. thinner materials. They can all be runned at full 60000RPM on all platforms. wood printed wood sign * max RPM = 45 printed pvc with fine detail fine detailed aluminum sign Up ut Bit Down ut bit = 1kW = 3kW MultiUT Ibag = 1kW MultiUT = 1kW max RPM 45 MultiUT Kavo = 1kW MultiUT HP = 3kW B IT-WDD Total Flute 2 1 Tip Shank Single flute Soft hard composite wood with top print laminate BITWDD (i-5712) 50 Up ut 16mm 5/8 BITWDD (i-5710) Double flute Bit Wood Soft hard composite wood with top print laminate Multi Purpose Bit RPM Bit name Total milling Bit Flute ollets Tip N/L/ Shank P Down ut Starter B IT-MUS

27 Bits * max RPM = 45 Up ut Bit Down ut bit = 1kW = 3kW MultiUT = 1kW MultiUT = 1kW max RPM 45 MultiUT HP = 3kW M M M M M M M M M RPM BITMUS mm 1/8" BITMUS /16" BITMUS /16" BITMUS /16" BITMUS /16" BITMUS /8" BITMDS Multi purpose, downcut, 1, 1/16" BITMDS Multi purpose, downcut, 2, 3/32" BITMDS Multi purpose, downcut, 3/16" BITMDS Multi purpose, downcut, 3/8" in thinner materials. They can all be runned at full 60000RPM on all platforms. The Super Sharp bits are grinded / polished for an optimized routing surface. acrylic with fine detail 3mm super sharp milling bits are ideal for milling many small details and inside radiuses Bit milling Total Flute Bit name Tip M Bit Shank ollets Single flute N/L/ Down ut P Acrylic Starter 3mm super sharp milling bits B IT-ADS

28 Bits Up ut Bit Down ut bit = 1kW = 3kW MultiUT = 1kW MultiUT = 1kW max RPM 45 MultiUT HP = 3kW M M M M M M M M M M M M M M M Bit Bit name milling RPM BITAUS mm 1/8" BITAUS /16" BITAUS /16" BITAUS mm 9/32" BITAUS /8" BITAUS /16" BITAUS /8" BITAUS /16" BITAUS /8" BITAUS mm 13/16" BITADS down-cut, single flute bit. 2, 3/32" BITADS down-cut, single flute bit. 3mm 1/8" BITADS down-cut, single flute bit. 3/16" BITADS down-cut, single flute bit. 3/16" BITADS down-cut, single flute bit. 3/8" This is our section for special purpose milling bits for engraving, high speed folding lines in AM (aluminum composite materials), outer radius, braiile mounting etc. See chart for details, milling thickness, max RPM, etc. engraved acrylic AM with v-notches milled wood radius detail Angle ollets Shank Diameter N/L / Shape P Engraving Bit Starter 6mm special purpose milling bits Bit * max RPM = 45 B IT-EB

29 Bits Folding Bits Engraving Bits Radius Bit Polishing Bit Braille Bit ompression Bit Straight ut Bit * max RPM = 45 = 1kW = 3kW MultiUT Ibag = 1kW MultiUT = 1kW max RPM 45 MultiUT Kavo = 1kW MultiUT HP = 3kW P N/L/ Starter 54 BIT-EB06-60 (i-6660) Engraving bits for acrylics, other synthetic materials and wood. 60 degree. Produces a bottom groove of 0,4mm mm 5/32 BIT-EB06-46 Special purpose milling bit for making crease lines in polypropylene. 46 degree. Produce a bottom groove of 0,4mm. (ball nose bit) mm 5/32 BIT-EB06-73 Folding for aluminum composite material, max 3mm 3mm 1/8 N/L/ BIT-EB0660-4F BIT-EB0690-4F M ibag BIT-EB BIT-EB06-94 (i-3772) BIT-EB F Hi-speed folding for aluminum composite material, 90 degree, max 4mm. Tip width 0,9mm produce a groove bottom of 1,8mm 4mm 5/32 Hi-speed folding for aluminum composite material, 120 degree 2 flute. ball nose with tip dia. 1,8mm 4mm 5/32 Hi-speed four flute folding for grey board and similar materials, max 5,2mm; this makes a 60 degree groove. Hi-speed four flute folding for grey board and similar materials, max 3mm; this makes a 90 degree groove. Hi-speed four flute folding for grey board and similar materials, max 1,7mm; this makes a 120 degree groove. 40 5,2mm 1/5 3mm 1/8 1,7mm 11/16 ollets P M ibag Radius Bit Outer, 6mm shaft radius 3, 4 to 6mm 5/32" to 1/4" 50' BITRBO Radius Bit Outer, 6mm shaft radius 3, 6 to 8mm 1/4" to 9/32" 50' BITRBO Radius Bit Outer, 6mm shaft radius 3, 8 to 9/32" to 3/8" 50' BITRBO Radius Bit Outer, 6mm shaft radius 3, 12 to 14mm 15/32" to 1/2" 50' Drilling bit for Braille. For drilling in acrylic, P, etc. BIT-BRAILLE06 Shaft 6mm,Tip : ,5 (0,0610 Inch) Workstogether with the Braille. 3mm 1/ Drilling bit for Braille. For use in harder materials like Aluminum, AM etc. BIT-BRAILLE06 Tip : 1,56mm (0,0615 Inch) Works together with the Braille. 3mm 1/8 20 This is a compression bit for smooth edges on both top and bottom liner. Acrylic, Polycarbonate, Sintra with two sided print laminate. 22mm - 1 Gatorplast, Ultraboard, Kappa with direct print or blank BITRBO BIT-RBO mm - 5/32 pr pass BIT-EB F five flute engraving bit for wood, MDF, hardboard, flooring etc 0,3mm BIT- MS (i-9152) BIT- MSD (i-6432) 50 Radius bit outer 6mm shaft, radius RPM Bit name milling Bit 4mm 5/32 BIT-EB06-40 (i-6630) Engraving bits for acrylics, other synthetic materials and wood. 40 degree. Produces a bottom groove of 0,4mm. RPM milling Bit name Bit ollets Starter 50 55

30 Accessories * max RPM = 45 MultiUT Ibag = 1kW MultiUT Kavo = 1kW MultiUT HP = 3kW accessories = 1kW MultiUT = 1kW max RPM 45 = 3kW accessories include adjustment sleeves, replacement chucks and maintenance items for the Kongsberg P/ and N/L/. See the chart for P N/L/ Starter Part no. Part name descriptions and machine compatibility. Adjustment sleeves Adjustment sleeve Multiut 20mm Use in order to get the right milling depth when changing bit Adjustment sleeve Multiut 28mm Engraving bits for acrylics, other synthetic materials and wood. 40 degree. Produces a bottom groove of 0,4mm. Dummy bits MultiUT head Dummy router bit 3mm L40 placed in chuck when milling spindle is not in use Dummy router bit 6mm L40 placed in chuck when milling spindle is not in use Dummy router bit 8mm L40 placed in chuck when milling spindle is not in use Dummy router bit 1/4 L40 placed in chuck when milling spindle is not in use ATA (Automatic Tool Adjust) Replacement chucks / collets for 3 kw Ibag mm replacement chuck 6mm replacement chuck 3mm replacement chuck 57

31 Accessories P N/L/ Starter Drawing s Part no. Part name Replacement chucks / collets for 1 kw Ibag 6mm replacement chuck 3mm replacement chuck This is our section for drawing s, including fiber tip pens, liquid pen inserts and ball point pen refills. Replacement chucks / collets for 1 kw Kavo 6mm replacement chuck huck maintenance kit huck maintenance kit Multiut (L / N) pen plot pen plot huck maintenance kit P Replacement plastic bags for acuum cleaner acuum cleaner 75l (industrial) acuum cleaner Dolphin acuum cleaner TB Esko Plastic bags for ac.leaner 75L tank (50pcs) Plastic bags vac. cleaner Dolphin (50pcs) Plastic bags for vac. vleaner TB Esko. (50pcs) 59

32 rease Wheels Drawing s P L N E Tool insert/unit Pen Pen name 1 crease wheels Pens for drawing or marking on different materials Fibretip pen Ø14 mm multifunction unit Fibretip Fibretip pen Ø14 mm multifunction unit Fibretip Liquid ink Ø14 mm multifunction unit Ball point pen Ø14 mm multifunction unit Ball point pen Ball point pen Ø14 mm multifunction unit Ball point pen Ball point pen Ø14 mm multifunction unit Ball point pen Ball point pen Ø14 mm multifunction unit Ball point pen Ball point pen Ø14 mm multifunction unit Ball point pen Ball point pen Ø14 mm multifunction unit Ball point pen Ball point pen Ø14 mm multifunction unit Ball point pen Ball point pen Ø14 mm multifunction unit Ball point pen PEN-FP317 For drawing on materials such as clear vinyl, which normally cannot be marked with ballpoint or liquid ink pens. Fiber tip pens, Lumocolor 317 WP6 (set of 8). Line thickness: medium 1.0 mm PEN-FP318 For drawing on materials such as clear vinyl, which normally cannot be marked with ballpoint or liquid ink pens, Fiber tip pens, Lumocolor 318 WP6 (set of 8). Line thickness: fine 0.6 mm PEN-LP164 Liquid ink pen insert. 0.3 black. For use with Liquid Ink Tool PEN-BP101 Medium line ball point pen refill, black. for high-speed plots on paper, Mylar foil or directly onto dieboard PEN-BP102 Medium line ball point pen refill, blue for high-speed plots on paper, Mylar foil or directly onto dieboard PEN-BP103 Medium line ball point pen refill, red for high-speed plots on paper, Mylar foil or directly onto dieboard PEN-BP104 Medium line ball point pen refill, green for high-speed plots on paper, Mylar foil or directly onto dieboard PEN-BP201 Bold line ball point pen refill, black for highspeed plots on paper, Mylar foil or directly onto dieboard PEN-BP202 Bold line ball point pen refill, blue for highspeed plots on paper, Mylar foil or directly onto dieboard PEN-BP203 Bold line ball point pen refill, red for highspeed plots on paper, Mylar foil or directly onto dieboard PEN-BP204 Bold line ball point pen refill, green for high-speed plots on paper, Mylar foil or directly onto dieboard crease wheels provide excellent performance when creasing thin materials such as folding carton and paper. folded carton package paper tent sign 61

33 rease Wheels L N P 26mm crease wheels E Tool insert Wheel Wheel name rease wheel Ø15 1 Point rease Wheel - 1 dia - 1-point rease wheel Ø Point rease Wheel - 1 dia point rease wheel Ø15 2 Point rease Wheel - 1 dia - 2-point rease wheel Ø15 3 Point rease Wheel - 1 dia - 3-point rease wheel Ø15 4 Point rease Wheel - 1 dia - 4-point rease wheel Ø15 1 mm spacing rease Wheel - 1 dia double edge 1mm spacing rease wheel Ø15 1,2 spacing rease Wheel - 1 dia double edge 1,2 spacing rease wheel Ø15 1,4mm spacing rease Wheel - 1 dia double edge 1,4mm spacing rease wheel Ø15 1,8mm spacing rease Wheel - 1 dia double edge 1,8mm spacing rease wheel Ø15 2,2mm spacing rease Wheel - 1 dia double edge 2,2mm spacing rease E rease mm crease wheels provide excellent performance when creasing thick carton and thin corrugated boards rease E rease rease E rease rease E rease 1 folded corrugated plastic sign rease E rease 1 creased and folded corrugated cases rease E rease rease E rease rease E rease rease E rease rease E rease 1 63

34 rease Wheels L N P E Tool insert Wheel Wheel name L N P E Tool insert Wheel Wheel name rease wheel Ø26 0,6mm spacing rease Wheel - 26mm dia double edge 0,6mm spacing rease wheel Ø26 Triple wall rease Wheel - 26mm triple wall rease wheel Ø26 rush rease Wheel - 26mm crush R= rease E rease 26mm rease wheel Ø26 1 Point rease Wheel - 26mm dia - 1-point rease E rease 26mm rease E rease 26mm rease wheel Ø26 2 Point rease Wheel - 26mm dia - 2-point rease E rease 26mm rease E rease 26mm rease wheel Ø26 3 Point rease Wheel - 26mm dia - 3-point rease E rease 26mm rease wheel Ø26 4 Point rease Wheel - 23mm dia - 4-point rease wheel Ø26 4 Point rease Wheel - 26mm dia - 6-point rease wheel Ø26 8 Point rease Wheel - 26mm dia 8-point rease wheel Ø26 10 Point rease Wheel - 26mm dia 10-point rease wheel Ø15 12 Point rease Wheel - 26mm dia 12-point rease wheel Ø15 14 Point rease Wheel - 26mm dia 14-point rease E rease 26mm rease E rease 26mm rease E rease 26mm rease E rease 26mm rease E rease 26mm rease E rease 26mm 65

35 rease Wheels N P L Tool insert / holder Perf wheel holder Wheel Wheel name 60mm crease wheels 60mm crease wheels All head insert positions HD position The 60mm crease for corrugated board offers improved crease quality over smaller wheel s. The increased frontal area (see sketch) allows going All head insert positions deeper into the board without cracking the liner, which is especially important for material with high recycle content. HD position rease Ø rease wheel Ø60 6 pont rease wheel 60mm dia - 6-point rease wheel Ø60 4 pont rease wheel 60mm dia - 4-point rease wheel Ø60 U shape rease wheel 60mm dia - U shape 60mm rease wheel holder rease Ø mm rease wheel holder All head insert positions HD position rease Ø mm rease wheel holder mm perforation s The comes with three different crease wheels; a 4-point wheel suitable for Eand other microflutes, a 6-point wheel suitable for B- and -flute, and a U-shaped All head insert positions rease Ø HD position wheel for double wall corrugated. Due to the large the wheel must be attached to the after it has been Perforation wheel holder Special wheel holder for fixing the perforation wheels Perforation wheel 3 x 3 mm Makes perforation lines with 3mm cut and 3mm space Perforation wheel 5 x 5 mm Makes perforation lines with cut and space Perforation wheel 5 x 7 mm Makes perforation lines with 7mm cut and space Perforation wheel 10 x 10 mm Makes perforation lines with cut and space 60mm rease wheel holder mounted in the head. The wheel easily snaps in place without any auxiliary All head insert positions requirements. rease Ø HD position 60mm rease wheel holder All head insert positions rease Ø HD position 60mm rease wheel holder All head insert positions corrugated shipping packages corrugated produce containers rease Ø HD position 60mm rease wheel holder All head insert positions HD position rease Ø mm rease wheel holder

36 rease Wheels 150mm crease wheels and crease blades L N P E Tool insert Wheel Wheel name 150mm crease wheels 150mm crease wheels provide excellent performance when creasing thick corrugated boards, including doulble and triple wall corrugated rease wheel Ø150 4 Point rease Wheel 150mm dia - 4-point rease wheel Ø150 6 Point rease Wheel - 150mm dia - 6-point rease wheel Ø150 6 Point 6 degrees rease Wheel - 150mm dia - 6-point 6 degrees rease wheel Ø150 U shape rease Wheel - 150mm dia - U shape rease wheel Ø150 shape rease Wheel - 150mm dia - shape Wheel Wheel name The big crease wheel positions on the N/L// (Power) and P () has the equivalent of 50kg [110lb.] of down-pressure, which is 2½ times more than the down-pressure of the conventional stations. The additional pressure, combined with the large frontal area of the big wheel enables excellent crease quality in heavy-duty corrugated board and even permits creasing board with high recycle content without breaking the liner. rease blades create superior creases in plastics where wheels are less effective. L N P E Tool insert rease blades 47mm Static knife double edge rease - 0. For thin, synthetic material such as polypropylene (PP) and polyethylene (PE) rease - 1mm For thin, synthetic material such as polypropylene (PP) and polyethylene (PE) Static knife double edge triple wall corrugated package creased thin plastics rease blades rease - 0. half For thin, synthetic material such as polypropylene (PP) and polyethylene (PE). Hi Force knife rease - 1mm half For thin, synthetic material such as polypropylene (PP) and polyethylene (PE). RM Knife rease 0, for RM knife For thin, synthetic material such as polypropylene (PP) and polyethylene (PE). RM Knife rease 1mm for RM knife For thin, synthetic material such as polypropylene (PP) and polyethylene (PE). Hi Force knife 68 69