Recessing. Recessing. Automatic

Transcription

1 Recessing contents Automatic Recessing Tools 2 Overview of Automatic Recessing 4 Tool Selection 5 AR Series Operating Principle 7 AR Automatic Recessing Heads Automatic Recessing GENERATING HEADS & PRECISION CHAMFERING 12 ARSP Automatic Recessing Short Pilot Heads 15 ARX Automatic Recessing External Heads 21 ARJ Automatic Recessing Jig Type Heads 26 ARXJ Heavy Duty Jig Type Heads 29 Head Conversion and Interchangeability 32 Pilots 35 Toolholders, Cutters, and Inserts 37 Set-up and Operation 41 Application Examples 45 Nobur JA/JC Deep Hole Automatic Recessing Heads 52 Set-up and Operation 54 Application Examples Generating Heads 55 Overview of Generating Heads 56 Operating Principle 58 Features and Options 60 Single-Slide Heads 62 Double-Slide Heads 64 Application Examples Precision Chamfering Tools 67 Nobur JB Back-Chamfering Tool 68 Operating Principle 71 CNF Series Precision Chamfering Tools 72 Operating Principle 77 Nobur JB & CNF Application Examples 82 Application Data Sheet COPYRIGHT 2003 COGSDILL TOOL PRODUCTS, INC CATALOG NO 400 US 1-04

2 overview Automatic Recessing Cogsdill offers the widest array of standard tooling and the broadest range of solutions for precision grooving, recessing, and internal and external facing and chamfering We will design and manufacture a complete tooling package for your application, including Automatic Recessing heads, cutters and pilots The wide variety of standard recessing heads described in this catalog are available from stock to suit most applications and machines Special recessing heads can be designed and manufactured for unusual applications GREATER ACCURACY, SHORTER CYCLE TIME, LOWER COST Cogsdill Automatic Recessing Tools will save you time and money Cycle time is reduced from minutes or hours to seconds The precision is built into the head so that grooves and recesses can be machined with exceptional accuracy and repeatability The Automatic Recessing head changes the operational direction by 90 (ie, axial spindle motion is converted to radial cutter movement) Recessing operations can be performed on a variety of machines, even on a drill press SUPERIOR CRAFTSMANSHIP All moving parts in our recessing heads are hardened and precision ground to ensure lasting accuracy and low maintenance costs Close tolerances virtually eliminate backlash during retraction, for accurate size on groove width as well as depth All sliding surfaces have large, hardened, load-bearing areas for long life and durability SUPERIOR CONSTRUCTION Compression of the head between the machine spindle and the workpiece or jig plate actuates a sliding inclined wedge mechanism, thereby extending the cutter Groove depth can be machined with great accuracy The cutter retracts radially prior to axial withdrawal of the tool from the bore, for accurate control of groove width This design also results in a constant linear relationship between spindle movement and cutter movement The straight-line movement of the cutter makes cutter regrinding easier 2

3 AR Recessing Head AR-S Recessing Short ARX Recessing Head ARX-S Recessing Short ARSP Recessing Head ARJ Recessing Head ARXJ Recessing Head Nobur JA-2000 Tool Nobur JA Tool Cutaway view of parts machined using Cogsdill Automatic Recessing Tools Grooves and recesses are machined with exceptional accuracy and repeatability 3

4 Automatic Recessing Quick Reference TOOL SELECTION CHART Cogsdill Automatic Recessing heads are stocked in eight basic categories, including the AR series and our Nobur recessing heads Head models are available to suit most applications and machining set-ups The chart below provides a brief overview of each head type, and identifies the types of machines to which each head is suited HEAD TYPE & DESCRIPTION NOTE: See photos on previous page MACHINE TYPE DRILL JIG MILLING CNC TOOL TURRET SCREW SPECIAL PRESS BORE MACHINE MACHINE LATHE LATHE MACHINE PURPOSE AR Automatic Recessing Pilots off workpiece or jig plate Micrometer stop controls depth of cut Tool adjustment controls axial location Through-shank coolant and overtravel shanks are standard AR-S Automatic Recessing Short Length Short-length head restricted to use on CNC machining or turning centers Does not have micrometer stop Depth of cut controlled by Z axis of the CNC machine; axial adjustment controlled by tool adjustment Throughtool coolant is standard ARSP Automatic Recessing Short Pilot Short, compact design For applications with work length restrictions Minimal overall length Pilots off workpiece Micrometer stop controls depth of cut Tool adjustment controls axial location Through-tool coolant and overtravel shanks are standard ARX Automatic Recessing External For external grooving Pilots off workpiece Micrometer stop controls depth of cut Tool adjustment is controlled within the fitted tooling Overtravel shanks are standard ARX-S Automatic Recessing External/Short Short-length head restricted to use on CNC machining or turning centers Does not have micrometer stop Depth of cut controlled by Z axis of the CNC machine; axial adjustment controlled by tool adjustment ARJ Automatic Recessing Jig Type Designed to run in a rotating bushing Pilots off jig plate Workpiece must be rigidly clamped Micrometer stop controls depth of cut Axial location is controlled by tool adjustment or adjustable thrust housing Through-tool coolant and overtravel shanks are standard ARXJ Automatic Recessing Heavy Duty Jig Type For machining large bores or for other special applications Pilots off workpiece or jig plate Cutter mounted on end of tool slide for rigid support in heavy cuts Micrometer stop controls depth of cut Axial location controlled by adjustable thrust housing Through-tool coolant and overtravel shanks are standard Nobur JA/JC Deep-Hole Recessing For deep-bore recessing and grooving Pilot-supported cutting action Micrometer-stop adjustment Multiple grooves, chamfers, or metering lands Back-chamfering and facing of deep bores 4

5 Operating Principle AR Series The AR Series Automatic Recessing Tool is made up of three basic components: head, cutter, and pilot The head is usually standard and consists of shank and tool body All cutters and pilots are manufactured to suit your application AR16 Recessing Head Micrometer Stop Shank with built-in Overtravel Spring Slipper Coolant Pipe Tool Slide Chip Guard Bearing Cutter with Insert Pilot 5

6 Operating Principle AR Series Illustrated below is the basic operating principle for AR, ARSP and ARX Recessing Heads The head type shown below is the AR model MACHINE SPINDLE FRONT BODY FEED STROKE TOTAL STROKE BALL BEARING PILOT RECESSING CUTTER 1 Approach Stroke The tool is rotating in a machine spindle The spindle is lowered, and the tool moves into position 2 Feed Stroke The pilot is located in the bore against the face of the workpiece Downward pressure causes compression of the recessing head, thereby actuating the slide mechanism which feeds the cutter out radially into the work 3 End of Feed Stroke The correct depth of cut is obtained when the micrometer stop bottoms against the front body, making it impossible to continue the cut Groove location is controlled by the tool adjustment system on the shank end of the cutter When the spindle is retracted, pressure is relieved, and the tool is withdrawn from the bore The cutter retracts and returns to its starting position The piloted bearing absorbs both thrust and rotation It remains stationary in the bore of the workpiece, under load, until the cutter is fully retracted, thereby preventing scoring of the workpiece 6

7 AR Series AR Recessing Head AR16 General purpose tool for use on: Drill presses Jig boring machines Milling machines CNC machines Tool lathes Turret lathes Horizontal boring machines Screw machines Special purpose machines Features: Pilots off workpiece or jig plate Micrometer stop controls depth of cut Tool adjustment controls axial location Through-shank coolant is standard Overtravel shanks are standard AR-S Short-Length Recessing Head A variation of the AR head is shown above Restricted to use on CNC machining or turning centers It does not have a micrometer stop for depth control Depth of cut is controlled by the Z axis of the CNC machine; axial adjustment is controlled by tool adjustment Through-tool coolant is standard 7

8 Specifications AR Series AR Recessing Head 'A' 'E' 'G' ø'b' 'F' 'H' ø'd' ø'c' 1 2 The Feed Ratio is the ratio of spindle to radial cutter movement INCH [METRIC] HEAD TYPE APPROX CAPACITY RANGE * MAXIMUM CUTTER TRAVEL SHANKS (A) FREE LENGTH (B) TOOL BODY (C) CUTTER SHANK (D) MASTER PILOT (E) REF MIN CUTTER LENGTH (F) BORE DEPTH Z (G) OVERTRAVEL (H) REF TO FRONT NUT AR10 AR16 AR [55] 0984 [250] 0590 [150] 1772 [450] 0866 [220] 2362 [600] 0197 [50] 0276 [70] 0394 [100] 0750in/20mm No 2 MT SK40/CAT40 BT in/25mm No 3 MT SK40/CAT40 SK50/CAT50 BT40 BT50 30mm/1500in/40mm SK40/CAT40 SK50/CAT50 BT40 BT [10370] 4894 [12432] 6248 [15870] 5657 [14370] 5547 [14090] 5796 [14723] 7713 [19590] 6299 [16000] 7122 [18090] 8152 [17890] 6591 [16740] 8756 [22240] 7343 [18650] 8165 [20740] 8087 [20540] ø158 [ø400] ø256 [ø650] ø315 [ø800] ø0394 [ø100] ø0630 [ø160] ø0787 [ø200] ø0591 [ø150] ø1416 [ø360] ø1772 [ø450] 148 [376] 203 [515] 243 [618] 085 [2160] 119 [3023] 146 [3708] 006 [15] 006 [15] 012 [30] 0157 [40] 0187 [476] 0224 [570] The capacity range shown is not intended as an absolute limitation The maximum diameter shown in the chart is defined as * the suggested maximum groove diameter, dependent upon cutting forces, and intended for the sake of comparison only 8

9 Bill of Materials AR Series AR Recessing Head Master Pilot 9 Coolant Pipe 20 Spring Plate Pipe 108 Oiler 2 Front Nut 10 Micrometer Nut 21 Centralising Pin 109 Retaining Screw 3 Back Plate 12 Over-rider Dowel 100 Set Screw 110 Micrometer Screw 4 Chip Guard 13 Slipper 101 Double Angular 103 Contact Bearing 111 Disc Springs 5 Front Body 14 Slipper Pin 103 Spring 112 Key 6 Toolslide 15 Copper Pad 104 Spring 113 Torx Screw 7 Rear Body 16 Shank 106 Tool Clamp Screw 114 Ball Bearing 8 Spring Plate 19 Back Plate Dowel 107 Tool Adjust Screw 115 Centralising Screw 9

10 Specifications AR Series AR-S Short-Length Recessing Head 'A' 'E' ø'b' 'F' 'G' ø'd' ø'c 1 2 The Feed Ratio is the ratio of spindle to radial cutter movement INCH [METRIC] HEAD TYPE AR10-S AR16-S AR20-S APPROX CAPACITY RANGE * 0216 [55] 0984 [250] 0590 [150] 1772 [450] 0866 [220] 2362 [600] MAXIMUM CUTTER TRAVEL 0197 [50] 0276 [70] 0394 [100] SHANKS SK40/CAT40 BT40 SK40/CAT40 SK50/CAT50 BT40 BT50 SK40/CAT40 SK50/CAT50 BT40 BT50 (A) FREE LENGTH 5705 [14490] 5114 [12990] 6758 [17166] 5345 [13576] 6168 [15666] 6089 [15466] 7461 [18951] 6048 [15361] 6870 [17451] 6792 [17251] 6327 [16070] 7870 [19990] 7870 [19990] 8181 [20780] 8614 [21880] 1500in/40mm The capacity range shown is not intended as an absolute limitation The maximum diameter shown in the chart is defined as * SK40/CAT40] the suggested maximum groove diameter, dependent upon cutting forces, and intended for the sake of comparison only SK50/CAT50] BT40 BT50 (B) TOOL BODY ø158 [ø400] ø256 [ø650] ø315 [ø800] (C) CUTTER SHANK ø0394 [ø100] ø0630 [ø160] ø0787 [ø200] (D) MASTER PILOT ø0591 [ø150] ø1416 [ø360] ø1772 [ø450] (E) REF MIN CUTTER LENGTH 148 [376] 203 [515] 243 [618] (F) BORE DEPTH 085 [2160] 119 [3023] 146 [3708] (G) REF TO FRONT NUT 0157 [40] 0187 [476] 0224 [570] 10

11 Bill of Materials AR Series AR-S Short-Length Recessing Head Master Pilot 8 Spring Plate 21 Centralising Pin 108 Oiler 2 Front Nut 9 Coolant Pipe 100 Set Screw 109 Retaining Screw 3 Back Plate 13 Slipper 101 Double Angular 103 Contact Bearing 113 Torx Screw 4 Chip Guard 14 Slipper Pin 103 Spring 114 Ball Bearing 5 Front Body 16 Shank 104 Spring 115 Centralizing Screw 6 Toolslide 19 Back Plate Dowel 106 Tool Clamp Screw 7 Rear Body 20 Spring Plate Pipe 107 Tool Adjust Screw 11

12 AR Series ARSP Short-Pilot Head Short, compact design for use on: CNC machining centers Turret lathes Tool lathes Screw machines Special purpose machines Features: For applications with work length restrictions Minimal overall length Pilots off workpiece Micrometer stop controls depth of cut Tool adjustment controls axial location Through-tool coolant Overtravel shanks are standard 12

13 Specifications AR Series ARSP Short-Pilot Head 'A' 'E' 'G' ø'b' 'F' 'H' ø'd' ø'c' 1 2 The Feed Ratio is the ratio of spindle to radial cutter movement INCH [METRIC] HEAD TYPE APPROX CAPACITY RANGE * MAXIMUM CUTTER TRAVEL SHANKS (A) FREE LENGTH (B) TOOL BODY (C) CUTTER SHANK (D) MASTER PILOT (E) REF MIN CUTTER LENGTH (F) BORE DEPTH (G) OVERTRAVEL (H) REF TO FRONT NUT ARSP1 ARSP [55] 0984 [250] 0590 [150] 1772 [450] 0118 [30] 0197 [50] 0750in/20mm No 2 MT SK40/CAT40 BT in/25mm No 3 MT SK40/CAT40 SK50/CAT50 BT40 BT [6375] 3322 [8437] 4675 [11875] 4085 [10375] 3699 [9395] 3948 [10028] 5864 [14895] 4451 [11305] 5274 [13395] 5195 [13195] 6327 [16070] 7870 [19990] 7870 [19990] 8181 [20780] 8614 [21880] 1500in/40mm The capacity range shown is not intended as an absolute limitation The maximum diameter shown in the chart is defined as * SK40/CAT40] the suggested maximum groove diameter, dependent upon cutting forces, and intended for the sake of comparison only SK50/CAT50] BT40 BT50 ø170 [ø4325] ø236 [ø600] ø0394 [ø100] ø0472 [ø120] ø0591 [ø150] ø1091 [ø277] 109 [276] 144 [365] 063 [160] 081 [205] 006 [15] 006 [15] 0160 [405] 0158 [400] 13

14 Bill of Materials AR Series ARSP Short-Pilot Head Master Pilot 10 Micrometer Nut 19 Back Plate Dowel 107 Tool Adjust Screw 2 Front Shell 12 Over-rider Dowel 100 Set Screw 110 Micrometer Screw 3 Back Plate 13 Slipper 101 Double Angular 103 Contact Bearing 111 Disc Springs 5 Front Body 14 Slipper Pin 104 Spring 112 Key 6 Toolslide 15 Copper Pad 105 Head Screw 103 Screw 7 Rear Body 16 Shank 106 Tool Clamp Screw 14

15 AR Series ARX External Head External grooving tool for use on: Drill presses Milling machines CNC machines Turret lathes Screw machines Special purpose machines Features: Pilots off workpiece Micrometer stop controls depth of cut Tool adjustment is controlled within the fitted tooling Overtravel shanks are standard Optional balance block available with two-slot chip guard for high-speed applications ARX-S External Short-length head A variation of the ARX head is shown above Restricted to use on CNC machining or turning centers It does not have a micrometer stop for depth control Depth of cut is controlled by the Z axis of the CNC machine; axial adjustment is controlled by tool adjustment 15

16 ARX Tooling Components AR Series ARX toolholder, cartridge, and insert are shown below Replaceable carbide inserts are used where applications permit SPECIAL PART PILOT ADJUSTMENT MASTER PILOT LOCKING SCREW AXIAL ADJUSTING SCREW RECESSING HEAD Drawing depicts adjustment of groove location, as measured from the end of the part CARBIDE INSERT INSERT CARTRIDGE TOOL HOLDER ARX toolholders, insert cartridges, and carbide inserts are made to order from standard blanks Part pilots are designed and manufactured to suit the application; the master pilot is part of the recessing head 16

17 Specifications AR Series ARX External Head 'A' 'G' ø'b' 'F' 'J' 'E' 2 1 The Feed Ratio is the ratio of spindle to radial cutter movement ø'd' 'H' 'C' CAP SCREWS INCH [METRIC] HEAD TYPE ARX10 ARX16 ARX20 CAPACITY RANGE PART GROOVE * DIAMETER LOCATION [40 200] [ ] [ ] UP TO 1250 [3175] UP TO 1375 [3493] UP TO 1500 [3810] MAXIMUM CUTTER TRAVEL 0197 [50] 0276 [70] 0394 [100] SHANKS 0750in/20mm No 2 MT SK40/CAT40 BT in/25mm No 3 MT SK40/CAT40 SK50/CAT50 BT40 BT50 30mm/1500in/40mm SK40/CAT40 SK50/CAT50 BT40 BT50 (A) FREE LENGTH 4083 [10370] 4894 [12432] 6248 [15870] 5657 [14370] 5547 [14090] 5796 [14723] 7713 [19590] 6299 [16000] 7122 [18090] 8152 [17890] 6591 [16740] 8756 [22240] 7343 [18650] 8165 [20740] 8087 [20540] (B) TOOL BODY ø158 [ø400] ø256 [ø650] ø315 [ø800] (C) CUTTER SHANK 0625 [1588] 1000 [2540] 1250 [3175] (D) MASTER PILOT ø0591 [ø150] ø1416 [ø360] ø1772 [ø450] (E) REF MIN CUTTER LENGTH 148 [376] 203 [515] 243 [618] (F) BORE DEPTH 085 [2160] 119 [3023] 146 [3708] (G) OVER TRAVEL 006 [15] 006 [15] 012 [30] (H) MOUNTING 0636 [1616] 1048 [2663] 1294 [3287] (J) REF TO FRONT NUT 0157 [40] 0187 [476] 0224 [570] * The capacity range shown is not intended as an absolute limitation It defines the normal range when using standard components The diameter range represents the approximate part diameter The groove location is the approximate distance to the groove measured from the end of the part 17

18 Bill of Materials AR Series ARX External Head A SECTION VIEW Master Pilot 8 Spring Plate 19 Back Plate Dowel 110 Micrometer Screw 2 Front Nut 9 Coolant Pipe 20 Spring Plate Pipe 111 Disc Springs 3 Back Plate 10 Micrometer Nut 21 Centralising Pin 112 Key 4 Standard Chip Guard 12 Over-rider Dowel 100 Set Screw 113 Torx Screw 4A Two Slot Chip Guard 13 Slipper 101 Double Angular 103 Contact Bearing 115 Centralizing Screw 5 Front Body 14 Slipper Pin 104 Spring 6 Toolslide 15 Copper Pad 108 Oiler 7 Rear Body 16 Shank 109 Retaining Screw 18

19 Specifications AR Series ARX-S External Short-Length Head 'A' 1 2 ø'b' 'F' 'E' 'J' The Feed Ratio is the ratio of spindle to radial cutter movement ø'd' 'H' 'C' CAP SCREWS INCH [METRIC] HEAD TYPE ARX10-S ARX16-S ARX20-S CAPACITY RANGE * PART DIAMETER [40 200] [ ] [ ] GROOVE LOCATION UP TO 1250 [3175] UP TO 1375 [3493] UP TO 1500 [3810] MAXIMUM CUTTER TRAVEL 0197 [50] 0276 [70] 0394 [100] SHANKS SK40/CAT40 BT40 SK40/CAT40 SK50/CAT50 BT40 BT50 SK40/CAT40 SK50/CAT50 BT40 BT50 (A) FREE LENGTH 5705 [14490] 5114 [12990] 6758 [17165] 5345 [13576] 6168 [15666] 6089 [15466] 7461 [18951] 6048 [15361] 6870 [17451] 6792 [17251] 6327 [16070] 7870 [19990] 7870 [19990] 8181 [20780] 8614 [21880] 1500in/40mm The capacity range shown is not intended SK40/CAT40] as an absolute limitation It defines the normal range when using standard * components The diameter range represents the approximate part diameter The groove location is the approximate distance to SK50/CAT50] the groove measured from the end of the part BT40 BT50 (B) TOOL BODY ø158 [ø400] ø256 [ø650] ø315 [ø800] (C) CUTTER SHANK 0625 [1588] 1000 [2540] 1250 [3175] (D) MASTER PILOT ø0591 [ø150] ø1416 [ø360] ø1772 [ø450] (E) REF MIN CUTTER LENGTH 148 [376] 203 [515] 243 [618] (F) TOOL SLIDE 085 [2160] 119 [3023] 146 [3708] (H) MOUNTING 0636 [1616] 1048 [2663] 1294 [3287] (J) REF TO FRONT NUT 0157 [40] 0187 [476] 0224 [570] 19

20 Bill of Materials AR Series ARX-S External Short-Length Head A Master Pilot 7 Rear Body 19 Back Plate Dowel 109 Retaining Screw 2 Front Nut 8 Spring Plate 20 Spring Plate Pipe 113 Torx Screw 3 Back Plate 9 Coolant Pipe 21 Centralising Pin 115 Centralising Screw 4 Std Chip Guard 13 Slipper 100 Set Screw 4A Two Slot Chip Guard 14 Slipper Pin 101 Double Angular 103 Contact Bearing 5 Front Body 15 Copper Pad 104 Spring 6 Toolslide 16 Shank 108 Oiler 20

21 ARJ Jig-Type Head AR Series Designed to run in a rotating bushing mounted in a jig plate A tool for use on: Drill presses Jig boring machines Milling machines Radial arm drills Rotary transfer machines Special purpose machines Multi-head spindles Features: Pilots off jig plate Workpiece must be rigidly clamped Micrometer stop controls depth of cut Axial location is controlled by tool adjustment or adjustable thrust housing Through-tool coolant is standard Overtravel shanks are standard Designed to run in a rotating bushing for exceptional rigidity, especially at high cutting speeds 21

22 Operating Principle AR Series ARJ and ARXJ Recessing Heads operate according to the basic principles as illustrated below The head type shown below is the ARJ model 1 Approach Stroke 2 Feed Stroke 3 End of Feed Stroke The ARJ tool is rotating in a machine spindle and piloting in the bushing The spindle is lowered The adjustable thrust housing bottoms against the face of the rotating bushing Downward pressure causes compression of the recessing head, thereby actuating the slide mechanism which feeds the cutter out radially into the work The correct depth of cut is obtained when the micrometer stop nut bottoms against the tool body, making it impossible to continue the cut Groove location is regulated by the adjustable thrust housing 22

23 Specifications AR Series ARJ Jig-Type Head 'A' 'G' ø'b' 'F' 'E' ø'd' Running bushing is shown in operating position ø'c' 1 2 The Feed Ratio is the ratio of spindle to radial cutter movement INCH [METRIC] HEAD TYPE APPROX CAPACITY RANGE * MAXIMUM CUTTER TRAVEL SHANKS (A) FREE LENGTH (B) TOOL BODY (C) CUTTER SHANK (D) RUNNING BUSHING (E) REF MIN CUTTER LENGTH MINIMUM (F) MAXIMUM (G) OVERTRAVEL ARJ10 ARJ16 ARJ [55] 0984 [250] 0590 [150] 1772 [450] 0866 [220] 2362 [600] 0197 [50] 0276 [70] 0394 [100] 1000in/25mm No 3 MT SK40/CAT40 SK50/CAT50 BT40 BT50 30mm/1500in/40mm SK40/CAT40 SK50/CAT50 BT40 BT50 30mm/1500in/40mm SK40/CAT40 SK50/CAT50 BT40 BT [19405] 7890 [20040] 9805 [24905] 8392 [21315] 9215 [23405] 9136 [23205] 8937 [22700] [28200] 9687 [24605] [26700] [26500] 8972 [22790] [28200] 9724 [24700] [26790] [26590] ø312 [ø7925] ø391 [ø9925] ø451 [ø1145] ø0394 [ø100] ø0630 [ø160] ø0787 [ø200] ø2677 [ø680] ø3937 [ø1000] ø4331 [ø1100] 108 [2747] 154 [392] 184 [466] 242 [6155] 248 [6295] 270 [6855] 478 [12135] 514 [13045] 476 [12095] 006 [15] 012 [30] 012 [30] * The capacity range shown is not intended as an absolute limitation The maximum diameter shown in the chart is defined as the suggested maximum groove diameter, dependent upon cutting forces, and intended for the sake of comparison only 23

24 Specifications AR Series ARJ Jig-Type Bushing 1 Housing 100 Needle Roller Bearing 102 Snap Ring 2 Spacer 101 Inner Ring 103 Grease Fitting METRIC [INCH] BUSHING No (A) (B) (C) (D) (E) (F) CAP HEAD SCREW ARJ10 RB ø45,0 [1772] ø67,975 [26726] ø78,0 [3071] 84,7 [3335] 60,0 [2362] 18,0 [0709] ARJ16 RB ø65,0 [2559] ø99,975 [39360] ø110,0 [4331] 116,7 [4594] 63,5 [2500] 19,05 [0750] M6x10P (2 pieces) ARJ20 RB ø80,0 [3150] ø109,975 [43297] ø120,0 [4724] 126,7 [4988] 63,5 [2500] 19,05 [0750] 24

25 Bill of Materials AR Series ARJ Jig-Type Head 2 Front Shell 12 Over-rider Dowel 104 Spring 111 Disc Springs 5 Front Body 13 Slipper 105 Caphead Screw 112 Key 6 Toolslide 14 Slipper Pin 106 Tool Clamp Screw 113 Caphead Screw 7 Rear Body 15 Copper Pad 107 Tool Adjust Screw 115 Centralizing Screw 8 Spring Plate 16 Shank 108 Oiler 9 Coolant Pipe 20 Spring Plate Pipe 109 Retaining Screw 10 Micrometer Nut 21 Centralising Pin 110 Micrometer Screw 25

26 ARXJ Heavy Duty Jig-Type Head AR Series For machining grooves or forms in large bores or for other special applications A tool for use on: Drill presses Jig boring machines CNC machines Milling machines Radial arm drills Rotary transfer machines Special purpose machines Multi-head spindles Features: Pilots off workpiece or jig plate Cutter mounted on end of tool slide for rigid support in heavy cuts Micrometer stop controls depth of cut Axial location controlled by adjustable thrust housing Through-tool coolant is standard Overtravel shanks are standard 26

27 Specifications AR Series ARXJ Heavy Duty Jig-Type Head 'A' 1 'G' 'F' 2 ø'b' 'C' The Feed Ratio is the ratio of spindle to radial cutter movement ø'd' 'E' INCH [METRIC] HEAD TYPE APPROX CAPACITY RANGE * MAXIMUM CUTTER TRAVEL SHANKS (A) FREE LENGTH (B) THRUST HOUSING (C) TOOL SLIDE (D) TOOL BODY (E) TOOL SLIDE (F) MINIMUM (G) OVERTRAVEL ARXJ10 ARXJ16 ARXJ [450] 315 [800] 2559 [650] 3937 [1000] 3150 [800] 5000 [1270] 0197 [50] 0276 [70] 0394 [100] 1000in/25mm No 3 MT SK40/CAT40 SK50/CAT50 BT40 BT50 30mm/1500in/40mm SK40/CAT40 SK50/CAT50 BT40 BT50 30mm/1500in/40mm SK40/CAT40 SK50/CAT50 BT40 BT [19405] 7890 [20040] 9805 [24905] 8392 [21315] 9215 [23405] 9136 [23205] 8937 [22700] [28200] 9687 [24605] [26700] [26500] 8972 [22790] [28200] 9724 [24700] [26790] [26590] ø312 [ø7925] ø391 [ø9925] ø500 [ø12700] ø085 [ø216] ø119 [ø3023] ø146 [ø3708] ø2281 [ø57925] ø3120 [ø7925] ø3673 [ø9330] 0625 [15875] 1000 [25400] 1250 [31750] 176 [447] 2415 [6134] 2683 [6815] 006 [15] 012 [30] 012 [30] * The capacity range shown is not intended as an absolute limitation The maximum diameter shown in the chart is defined as the suggested maximum groove diameter, dependent upon cutting forces, and intended for the sake of comparison only 27

28 Bill of Materials AR Series ARXJ Heavy Duty Jig-Type Head ARXJ-P PILOT ASS'Y Front Shell 10 Micrometer Nut 20 Centralising Pin 110 Micrometer Screw 5 Front Body 12 Over-rider Dowel 21 Spring Plate Pipe 111 Disc Springs 6 Toolslide 13 Slipper 104 Spring 112 Key 7 Rear Body 14 Slipper Pin 105 Caphead Screw 113 Caphead Screw 8 Spring Plate 15 Copper Pad 108 Oiler 115 Centralising Screw 9 Coolant Pipe 16 Shank 109 Retaining Screw 28

29 Head Conversion INTERCHANGEABILITY OF COMPONENTS AR Series With the AR Series, we have refined the design of our complete system of automatic recessing heads so that many head types utilize some common components AR Series heads come in three standard sizes, based upon the cutter shank diameter as expressed in millimeters: 10, 16, and 20 A prefix is added to the size in order to identify the particular head type (eg, AR10, ARJ16, ARX20) Within a given size range, it may be possible to convert one head type into another style by merely changing a few parts The basic AR unit is a toolholder/insert-style head for internal grooving and recessing While different versions of the heads are available to perform specific machining operations, each head can be converted to a different style of the same size by changing a few key components A typical example (AR16 Recessing Head) is shown below Some components within the head must be changed in order to accommodate various cutter styles Please consult our customer service department if you have any questions regarding head conversions Special Internal Applications (Toolholder/Insert) Pilot to Suit Specific Application AR Type (Toolholder/Insert) Internal Features ARX Type (Toolholder/Cartridge/Insert) External Features 29

30 Head Conversion INTERCHANGEABILITY OF COMPONENTS AR Series AR Recessing Head Basic internal unit with toolholder & pilot for internal grooving operations ARX Recessing Head External unit with end mount toolholder & pilot for internal grooving operations on large diameters ARX Recessing Head External unit with external toolholder, cartridge, & pilot for OD grooving operations 30

31 Interchangeability of Shanks AR Series AR SERIES SHANKS HEAD TYPE AR10 ARX10 ARSP1 STANDARD SHANKS 0750 in 200 mm No 2 MT SK40 CAT40 BT40 This chart lists standard stocked shanks for the complete AR series, with the exception of the short-length heads shown below All shanks not listed are considered special; request a quotation AR16 ARJ10 ARX16 ARSP2 ARXJ in 250 mm No 3 MT SK40/SK50 CAT40/CAT50 BT40/BT50 AR20 ARJ16 ARJ20 ARX20 ARXJ16 ARXJ in 300 mm 400 mm SK40/SK50 CAT40/CAT50 BT40/BT50 AR-S SERIES SHANKS HEAD TYPE AR10-S ARX10-S AR16-S ARX16-S STANDARD SHANKS SK40 CAT40 BT40 SK40/SK50 CAT40/CAT50 BT40/BT50 This chart lists standard stocked shanks for short-length AR-S series heads; these heads are available only with shanks as shown (Short-length AR-S series heads are shorter versions of standard AR and ARX heads, restricted to use on CNC machining centers Depth of cut is controlled by the Z-axis of the machining center) AR20-S ARX20-S SK40/SK50 CAT40/CAT50 BT40/BT50 31

32 Pilots AR Series Pilots are required to locate and stabilize the recessing head in the component bore All pilots are manufactured to suit the application Although the basic design and dimensions are standardized as shown on page 33, the locating diameter of the pilot is designed specifically for your component Part pilots are retained in the master pilot by three retaining screws 32

33 Specifications PILOTS AR Series MASTER PILOT PART PILOT 3-DRILL DIMPLES øg x H INCL EQUI-SPACED AS SHOWN D øe øa øc max F x 45 B INCH [METRIC] Note: If machine lacks internal coolant capability, part pilot must be designed with coolant windows HEAD PILOTS (ØA) [-0008] (B) (ØC) MAX (D) -005 [-013] (ØE) -005 [-013] (F) (G) (H) ARSP [14995] 394 [1000] 472 [1200] 098 [250] 909 [2310] 394 [100] 138 [350] 120 ARSP [27675] 551 [1400] 969 [2460] 098 [250] 1409 [3580] 394 [100] 138 [350] 120 AR10 ARX [14995] 500 [1270] 472 [1200] 100 [255] 844 [2145] 394 [100] 138 [350] 120 AR16 ARX [3595] 551 [1400] 1295 [3290] 130 [330] 1811 [4600] 394 [100] 138 [350] 120 AR20 ARX [4499] 748 [1900] 163 [414] 148 [375] 2299 [5840] 394 [100] 177 [450] 120 ALL UNSPECIFIED DIMENSIONAL TOLERANCES ARE ±0005 [013] 33

34 Piloting Methods AR Series Pilots on ID and stops on face of component Pilots on OD and stops on face of component Pilots and stops on fixture plate Pilots on fixture plate and stops on face of component 34

35 Toolholders, Cutters, Inserts AR Series Toolholders are designed to suit the application The basic design of the toolholder is standardized (see page 36), but the diameter and length of the holder is designed to suit your component Toolholders with replaceable inserts are used where application parameters permit As a general rule, toolholders for holes 9/16 inch (approx 145mm) and larger utilize replaceable inserts Cutters for smaller diameters are usually of brazedcarbide or high-speed steel construction Our improved toolholder design allows fast and easy incremental adjustment of axial groove location without removing the toolholder from the head Many inserts can be manufactured from standard blanks (see bottom of page 36) Toolholders and inserts can be designed for back-chamfers, thread reliefs, multiple grooves, and special groove geometries; submit a part print and request a quotation Toolholders can be designed with an internal coolant port where required (see example below) Coolant Port Our improved toolholder design allows fast and easy incremental adjustment of axial groove location without removing the toolholder from the head (See set-up and operation guide on page 37 for more information) 35

36 Specifications TOOLHOLDER AR Series D J G RAD N MAX 45 ø E x H DEEP HOLE FIT øe x F LONG DOWEL ØM (THRU COOLANT) øa R C x 45 METRIC [INCH] HEAD TYPE ARSP 1 ARSP 2 AR10 AR-S10 ARJ10 (A) 1000 [0394] 1200 [0472] 1000 [0394] (B) 1270 [0500] 1725 [0679] 2080 [0819] (C) 050 [0020] 050 [0020] 050 [0020] (D) 900 [0354] 1250 [0492] 1525 [0600] (E) 150 [0059] 300 [0118] 150 [0059] (F) 300 [0118] 500 [0197] 300 [0118] P FLAT B (G) h [0028] 160 [0063] 080 [0031] (H) 230 [0091] 340 [0134] 220 [0087] (J) 335 [0132] 575 [0226] 670 [0264] (K) 800 [0315] 950 [0374] 775 [0305] ø(m) 300 [0118] 300 [0118] 300 [0118] (N) max 050 [0020] 050 [0020] 050 [0020] (P) 950 [0374] 1550 [0610] 1900 [0748] (R) 070 [0028] 080 [0031] 070 [0028] AR16 AR-S16 ARJ16 AR20 AR-S20 ARJ [0630] 2000 [0787] 2950 [1161] 3630 [1429] 050 [0020] 050 [0020] 1950 [0768] 2540 [1000] 300 [0118] 500 [0197] 500 [0197] 600 [0236] 160 [0063] 175 [0069] 340 [0134] 425 [0167] 610 [0240] 1000 [0394] 1250 [0492] 1550 [0610] 400 [0157] 500 [0197] 050 [0020] 050 [0020] 2650 [1043] 3330 [1311] 080 [0031] 100 [0039] AR Series Replaceable Inserts Standard insert blanks Replaceable carbide inserts are used where applications permit Special or intricate geometries are available 36

37 Set-up AR Series There are four basic steps to the set-up of AR Series Automatic Recessing heads (Set-up procedures differ somewhat for internal and external heads) 1 Install pilot For all head types except ARJ, the pilot must be installed in the head The pilot will fit either directly into the sealed bearing or into a master pilot for quick and easy tool changes 2 Install cutter/toolholder The cutter normally comes in three different styles: High-speed steel cutter Tungsten carbide brazed-tip cutters Replaceable-insert toolholders For internal recessing heads, install the cutter in the head with the cutting edge pointing in the direction of cut (ie, in the direction of toolslide movement) The cutter is clamped and fixed in position by two set screws in the head The cutter must be positioned radially in the head so that the cutting edge will be on center as the tool moves out to cut This is facilitated by the use of a key in the cutter shank, which automatically aligns the cutting edge on center For external recessing heads, install the toolblock onto the toolslide and secure in place with two caphead screws An adjustable cartridge is fitted to the toolblock and held in place by a buttonhead screw An inexpensive, replaceable insert is fitted to this cartridge and secured in place by an insert screw The cutting edge of the insert is automatically aligned on center as the toolblock is secured to the head For ARXJ heads, install a fixed cartridge onto the end of the toolslide and secure in place with caphead screws Replaceable inserts can be fixed to this cartridge with insert screws The cutting edge is automatically aligned on center as the cartridge is secured in the head 3 Set cutter projection from pilot For all head types except ARJ and ARXJ, the projection of the cutter from the pilot must be set properly in order to achieve accurate groove location For internal recessing heads, groove location is controlled by the tool adjustment set screw, which is located in the toolslide The tool adjustment screw is accessed through a hole in the chip guard on the front shell Insert the toolholder until it bottoms out in the toolslide Tighten tool adjustment screw and move cutter out until the set dimension (between cutter and pilot) is achieved Then lock the cutter in place by tightening the locking set screws For external recessing heads, groove location is controlled by a set screw in the end of the adjustable cartridge that is mounted on the toolblock Once the groove location is set, lock the cartridge in place with the buttonhead locking screw For ARJ and ARXJ heads, groove location is controlled by an adjustable thrust housing on the externally threaded front body ARJ heads have both the tool adjustment screw and the adjustable thrust housing for infinite cutter control 37

38 Set-up AR Series (continued) 4 Depth of cut/tool travel For all head types except AR-S and ARX-S (short length heads), depth of cut is controlled by a micrometer nut that allows the head to pre-set off the machine The standard tool feed ratio for all heads is 2:1 (ie, the ratio of spindle to radial cutter movement) Refer to the drawing supplied with the tool for the set-up dimension If the drawing is unavailable, follow this procedure: Add the depth of cut (the distance from the ID of the bore to the bottom of the groove) to the clearance between the cutter and the ID of the bore Multiply this figure by the feed ratio (ie, multiply by 2 for standard feed ratio) in order to arrive at the distance to set the micrometer nut from the front body This distance should be set using gauge blocks or by fine-tuning the micrometer nut position manually to achieve the desired groove depth HEX WRENCHES REQUIRED FOR ADJUSTING AR HEADS HEAD TYPE AR10 AR16 AR20 ARSP-1 ARSP-2 MICROMETER NUT SCREW 15mm 30mm 40mm 15mm 25mm INSERT TOOL HOLDER (LENGTH ADJ) 20mm 30mm 40mm 15mm 25mm Approximate adjustment gap for all internal recessing heads, when tool is in set position SET SCREW IN MASTER PILOT 15mm 15mm 20mm 15mm 15mm For AR-S and ARX-S (short length) heads, the depth of cut is controlled by the Z-axis of the CNC machining center 076mm (0030 ) CUTTER ADJUSTMENT OUT Cutter projection from Locating Face Carbide Insert Toolholder Master Pilot Part Pilot 38

39 Operation AR Series Speeds & Feeds Please refer to the charts below for speed and feed recommendations for specific material types The charts are intended as a guide or starting point; the actual speed and feed used will depend on a number of factors, including type of machine, condition of machine spindle, rigidity of fixturing, type of coolant used or dry cutting, tool length, cutter geometry, interrupted cut, etc INCH MATERIAL CUTTING SPEED (FT/MIN) FEED RATE (INCHES/REV) TOP RAKE (DEGREES) HSS Carbide HSS Carbide HSS Carbide Aluminum Brass Bronze Cast Iron Copper Magnesium Malleable Cast Iron Resin (Plastic) Free Cutting Steel Annealed Steel Wrought Steel Alloy Steel Tool Steel Monel & Stainless METRIC MATERIAL HSS CUTTING SPEED (M/MIN) Carbide Aluminum ,05 0,13 0,05 0, Brass ,05 0,13 0,05 0, Bronze ,05 0,13 0,05 0, Cast Iron ,05 0,10 0,05 0, Copper ,05 0,10 0,05 0, Magnesium ,10 0,15 0,10 0, Malleable Cast Iron ,05 0,10 0,08 0, Resin (Plastic) ,10 0,15 0,10 0, Free Cutting Steel ,05 0,10 0,08 0, Annealed Steel ,05 0,10 0,08 0, Wrought Steel ,05 0,08 0,08 0, Alloy Steel ,05 0,08 0,08 0, Tool Steel ,03 0,05 0,05 0, Monel & Stainless ,03 0,08 0,05 0, HSS FEED RATE (MM/REV) Carbide HSS TOP RAKE (DEGREES) Carbide 39

40 Operation AR Series (continued) Coolant Regarding the use of coolant, follow normal machine shop procedures for the cutter material and the material to be machined Lubrication 1 We recommend a water resistant grease for use in these heads Kluber Altemp Q NB50 has been thoroughly tested and found to perform exceptionally well it is the only grease we recommend It should be applied to all moving parts and surfaces when the head is disassembled for cleaning and maintenance, or if the head will be stored for extended periods Disassembly and cleaning should be done periodically 2 To lubricate the heads during use, apply Kluber Altemp Q NB50 grease through the external oilers or grease fittings on the head This should be done on a weekly basis, or more frequently if necessary Lubrication frequency can vary depending on the working environment, operational speed, coolant used, and number of cycles Remember, adequate lubrication is vital to long head life and trouble-free performance 3 A high-pressure hand pump lube gun is available from Cogsdill to make routine maintenance easy (Ref Part No CN-D24) 40

41 Applications AR Series AR10 Internal Recessing Head performing an ID grooving operation; pilots in part ARSP1 Internal Recessing Head machining an ID groove with a radius on a banjo fitting; pilots in part 41

42 Applications AR Series AR20 Internal Recessing Head machining a back-spotface with an ID chamfer; pilots in part AR16 Internal Recessing Head performing an ID grooving operation; pilots in fixture plate 42

43 Applications AR Series ARX10 External Recessing Head performing an OD grooving operation; pilots on part OD and includes balance weight ARX16 External Recessing Head machining a face and a double groove on an OD; pilots on part OD 43

44 Applications AR Series ARJ10 Jig-Type Recessing Head machining snap ring groove on each end of a 6-foot-long part Special Recessing Head machining three grooves simultaneously 44

45 Nobur JA/JC Series DEEP HOLE Nobur JA Recessing Head For deep bore recessing and grooving A tool for use on: Drill presses Jig boring machines Milling machines CNC machines Tool or turret lathes Horizontal boring machines Special purpose machines Features: In-bore pilot supports cutter along its entire length eliminates tool deflection; ensures concentricity through rigid cutting action Micrometer-stop adjustment Multiple grooves, chamfers, or metering lands O-ring and retaining ring grooves Relief grooves and tube sheet grooves Back-chamfering and facing of deep bores 45

46 Nobur JA/JC Series DEEP HOLE Nobur JA2000 Recessing Head For deep bore recessing and grooving Designed for heavier cuts than the regular JA Innovative internal coolant system directs coolant to cutting edges for improved chip evacuation, longer tool life, better tool function, and improved repeatability For use on machines with internal coolant capability * Features: Same in-bore pilot support and micrometer-stop adjustment as the regular JA Capable of wider cuts than the regular JA in some applications Extremely durable high-load precision dual bearings for long life Easy disassembly and reassembly for maintenance Overtravel units available upon request * JA2000 Recessing Heads can be ordered in a Side-Port model for use on machines that do not have through-spindle coolant capability Through-shank coolant is standard; specify side-port coolant if desired 46

47 Operating Principle Nobur JA/JC Series DEEP HOLE 1 Approach Stroke The Nobur JA tool is rotating in a machine spindle The spindle is lowered The tool approaches entry into the bore 2 Feed Stroke The pilot is located in the bore, stopping against the face of the workpiece Downward travel of the machine spindle compresses the tool so that the cutter feeds out radially into the surface of the workpiece The pilot rigidly supports the cutter along its entire length to eliminate deflection and ensure concentricity 3 End of Feed Stroke Radial depth of cut is obtained when the micrometer-stop nut bottoms out Groove location is controlled by the adjusting stopcollar, which moves the nosepiece up or down to position the cutter arm for accurate groove location 47

48 Specifications Nobur JA/JC Series DEEP HOLE ø C ø B E F CUTTER PILOT ARM NOSE PIECE D CUTTER ARM A FOR DIAMETERS <= ø9/16 ARM 1 CUTTER FOR DIAMETERS >= ø9/ The Feed Ratio is the ratio of spindle to radial cutter movement HEAD TYPE JA JA2000 JC in CAPACITY 1 mm (A) FREE in mm in mm (B) in mm (C) (D) MAXIMUM in mm (D) MINIMUM in mm (E) SHANKS 2 3/4 straight acme 1-1/16 12 acme #2 morse taper #3 morse taper 1 straight 4 1-1/2 straight #3 morse taper #4 morse taper in (F) mm Capacity means the suggested maximum groove diameter Dependent upon cutting forces and bore diameter Stated capacity is for steel 2 Shank is included with head Shanks other than shown can be supplied upon request 3 Supplied with through-tool coolant 4 Through-shank coolant is standard; specify side-port coolant if desired 48

49 Bill of Materials Nobur JA/JC Series DEEP HOLE Nobur JA Recessing Head Body Holder 5 Bearing Assembly 9 Stop 9 Collar-Adjustment 13 Pin 2 Adjustment Nut 2 Assembly 6 Collar Hub Mounting 10 Retainer Ring-Insert 14 Spacer/Bushing/ 14 Spring 3 Snap Ring 7 Leaf Spring (Quantity 3) 11 Lock Screw 15 Compression 15 Spring Return 4 Housing-Bearing 4 Stop Collar 8 Screw 8 Locking-Housing 12 Retainer Loop 49

50 Bill of Materials Nobur JA/JC Series DEEP HOLE Nobur JA2000 Recessing Head Through-Shank Coolant (standard) Side-Port Coolant option NOTE: Coolant location can be changed in the field; consult Sales Department 1 Spindle 8 Stop Nut 15 Cone Point Screw 22 Retaining Ring 2 O-Ring 9 Socket Head Cap Screw 16 Leaf Spring Details 23 thru 27 optional 3 Compression Spring 10 Bearing Sleeve 17 Coolant Tube 23 Outer Bearing Spacer 4 Spacer Bushing 11 Ball Bearing 18 Housing 24 Inner Bearing Spacer 5 Pin 12 Outer Bearing Spacer 19 Flat Point Set Screw 25 O-Ring 6 Drive Pin 13 Inner Bearing Spacer 20 Bearing Retainer 26 Coolant Nipple 7 Flat Point Set Screw 14 Bearing Collar 21 Stop Collar 27 Pipe Plug (not shown) 50

51 Bill of Materials Nobur JA/JC Series DEEP HOLE Nobur JC Recessing Head Body Holder 6 Bearing 11 Screw 16 Pad-Spring Retaining 2 Adjustment Nut Rear 7 Housing-Bearing 7 Stop Collar 12 Leaf Spring-Bottom 17 Pin 3 Screw 8 Screw 13 Retainer Collar 18 Assembly Pull Yolk 4 Snap Ring 9 Leaf Spring-Upper 14 Screw 19 Compression Spring 5 Snap Ring 10 Stop Collar 10 Adjustable 15 Screw 20 Transport Sleeve 51

52 Set-up Nobur JA/JC Series DEEP HOLE Cogsdill Nobur JA/JC tools are easily set Since the precision feed motion is built into the head, only two adjustments are required in order to properly set up a tool for operation Occasionally, compensating adjustments might be required if there is an error in the initial settings, or to compensate for cutter wear However, by following the steps prescribed below, it will be easy to attain the initial set-up 1 Set front stop collar This setting determines the position of the groove(s) relative to the face of the part, or other surface from which the tool actuates Simply adjust the threaded stop collar, measuring from the face of the collar to the top corner of the cutter until the correct distance is established (refer to photo A) Once set, the locking screw on the outer tool body should be tightened A 2 Set the groove diameter to be cut On manually fed machines, this setting is established by adjusting the threaded diameter stop nut at the rear of the tool body Because the cutter motion is radial, the groove cut diameter can be measured by using a micrometer to measure directly across the pilot and cutting edge when the head is compressed (refer to photo B) Since the pilot is 002 in (005mm) under the smallest bore diameter, the cutter should project from the pilot for a distance equal to the required depth of cut An alternative setting method is to measure the projection of the cutter using a surface plate indicator relative to the centerline of the bore Setting the groove diameter for machines with power feed requires that the diameter stop nut be backed away (toward the rear of the tool) so that it becomes nonoperative Tools with Acme-threaded shanks do not have the diameter stop nut The automatic feed on the machine is then set to produce the cutter projection required to cut the desired groove diameter Preset holders and gauges may also be used to establish the spindle travel limits Since cutter deflection is eliminated due to the support of the cutter by the arm and pilot, no compensation is required Once the above settings are verified, the tool is ready to use However, please remember that variations in bore diameter can cause groove dimensions to vary A variation of 001 in (002mm) in bore diameter can result in a 002 in (005mm) variation in groove diameter Therefore, bore tolerances must be limited to less than 1/2 of the tolerance required for the groove diameter If this tolerance requirement presents a problem, it might be necessary to pilot the tool in a fixture instead of piloting in the bore The diagram on page 53 shows how to measure a tool to cut a specific diameter B 52

53 Set-up and Operation Nobur JA/JC Series DEEP HOLE (continued) Diameter Setting Methods BY MICROMETER BY INDICATOR S S1 OR S = Groove Dia + Bore Dia 2 S = Groove Dia + Pilot Dia S1 = Groove Dia In order to measure for a specific groove cut diameter, the tool must be actuated to the limit setting by compressing the actuating assembly against the diameter stop nut The nominal clearance between the pilot diameter and the minimum bore diameter is 002 (05mm) Tool Operation Cogsdill Nobur JA/JC Recessing tools operate automatically as axial spindle travel is converted into radial cutter travel within the head The pilot enters the bore and the stop collar contacts the front of the part Continued spindle travel results in corresponding cutter travel which is rigidly supported within the part for extreme accuracy A sealed bearing between the tool body and the stop collar prevents marking of the workpiece Tool Lubrication In applications where water soluble or synthetic coolants are used, we recommend that, when the machine and tool are idle, the tool be removed from the spindle and immersed in oil to keep it lubricated and to prevent rusting of the internal mechanism Radial cutter advancement is approximately 1/2 of spindle travel Depth of cut is precisely controlled by an adjustable diameter stop nut located on the back end of the tool A feed rate of IPR ( mm) is generally used Upon completion of the cut, tool withdrawal feed should be at the cutting feed rate until the stop collar no longer contacts the part This will ensure that the cutter has fully retracted into the pilot before the tool is withdrawn from the part 53

54 Applications Nobur JA/JC Series DEEP HOLE Nobur JA Recessing Head machining eight metering lands in one pass CUT LOCATIONS Nobur JA Recessing Head performing grooving operation with piloting area in advance of cut PART LAYOUT Nobur JA Recessing Head back-cutting five locations Coolant FITTING FOR COOLANT LINE (OPTIONAL) Coolant 54

55 overview Generating Heads For facing, recessing, boring, and contouring Multiple operations can be performed faster, more economically, with better quality, and at one spindle location Used on special-purpose machines and other high production machinery, including transfer lines and dial machines Single or double-slide models are available, designed for feed-out or feed-in Sizes from 100 to 250mm (3937 to 9842 in) in diameter Drawbar actuation- no need to pilot in part or fixture Unique actuator design- smooth, accurate motion for precise repeatability Internal mechanism manufactured to exacting tolerances- backlash is virtually eliminated All moving parts are hardened and precision ground for lasting accuracy Built-in lubeways and easily accessible grease fittings Equipped with through-tool auto lube capability Special lightweight slides are available (optional) for higher cutting speeds and shorter cycle times- tooling can be balanced CUSTOM-DESIGNED Custom-designed top tooling is mounted in qualified holes on the toolslide Standard inserts are used for most applications Special head designs and special form cutters are available Cogsdill generating heads are designed to work on machines where the tool slide stroke is controlled by a drawbar The drawbar can produce finite, accurate movements in the tool slide(s), allowing the head to perform accurate machining operations Drawbars can either push or pull on the actuator, and may be controlled by CNC, hydraulic, or mechanical action Operations such as boring, turning, facing, chamfering, and form cutting can be easily performed Generating heads can often be made to perform multiple operations in a single pass this provides for optimum efficiency and performance in your machining operations Cogsdill generating heads are made from the highest quality materials, to exacting quality standards Our engineers have built in quality features that ensure durability and consistent accuracy These high-quality features include hardened and ground components, multiple grease fittings with internal lube ways, and anti-friction coatings on wear surfaces 55

56 Operating Principle Generating HEADS The method of operation incorporated in all Cogsdill generating heads is based on the principal of a sliding inclined wedge This actuation mechanism produces smooth, linear cutter movement with little or no backlash Slipper Lube Ways Slide Block Cross Slide Generating Head sliding inclined wedge mechanism and lubeways SHOWN ABOVE 56

57 Operating Principle Generating HEADS Cogsdill generating heads can be utilized on a variety of drawbar-equipped machines such as transfer lines, rotary transfer (dial type) machines, and other special purpose machines The heads can be mounted on virtually any spindle that has a drawbar Cogsdill can provide a complete tooling package for new machines, as well as for retrofitting an existing machine 70 04R 35 05x45 ø ø320 ø335 (INTER) ø This typical component requires three machining operations: a face, an ID groove, and an OD chamfer All operations will be completed at one station with one pass of the Cogsdill generating head Drawbar stroke on the machine will control cutter movement 1 HEAD MOVEMENT The part is in position The rotating machine spindle moves the generating head toward the part to begin the operation sequence The drawbar and cross slide are in the home position TOOL SLIDE MOVEMENT DRAWBAR MOVEMENT 2 The head is now in position The drawbar begins to pull, causing the cross slide and cutters to move radially across the part as the cutting stroke begins The face is cut first, followed by the ID groove, and then the OD chamfer 3 The head is now at full drawbar stroke, and the cuts have been completed The drawbar is then pushed back to the home position, thereby retracting the cutters The spindle then retracts and the head is pulled away from the part and returned to the position shown in step one 57

58 Features & Options Generating HEADS Cogsdill generating heads are available as standard products in single-slide and double-slide models, ranging in diameter from 100mm to 250mm (approximately 4 to 10 inches) The head type used generally depends on the operation(s) being performed and the speed at which the head is run Top tooling packages can be designed by our engineers to suit individual requirements Specially designed heads are available when required to meet unique part requirements or production challenges Auto-lube Our auto-lube feature enhances the longevity of the generating head by ensuring that all parts are consistently lubricated Every Cogsdill generating head comes with auto-lubrication capability as a standard feature Lubrication is fed to the head through the drawbar and actuator shaft This feature can add many thousands of cycles to the life of the head, while eliminating the need to perform manual lubrication on a daily basis Installation is easy on machines with spindles that have through-lube capability Most commercial auto-lube systems installed on machines are more than adequate for use with Cogsdill generating heads The heads are usually lubricated automatically several times per shift, depending on the type of lubrication system available When used in conjunction with an oil mist system (ISO68 grade oil), the flow rate is usually adjusted to a moderately low setting For specific questions regarding the auto-lube feature, please consult with our engineering group Lubrication Recommendations All heads may be manually lubricated via grease fittings in the main body if a through-lube system is not available on your machine If these heads are not used with an automatic lubrication system, it is necessary to manually lubricate them at least weekly More frequent lubrication may be necessary depending on the operational speed, type of coolant used, rapid cycling, and other factors Kluber Altemp Q NB50 has been thoroughly tested and found to perform exceptionally well it is the only grease we recommend Using a grease gun, inject one or two pumps of grease into each grease fitting Remember, adequate lubrication is vital to long head life and trouble-free performance It is also recommended that Kluber Altemp Q NB50 grease be applied to all moving parts and surfaces when the head is disassembled for maintenance and cleaning, or if the head is to be stored for extended periods (Note: if the head is being used with an oil mist automatic lube system, do not use the Kluber grease during disassembly and cleaning Instead, use the same recommended ISO68 oil that is fed through the lube system It is important not to mix the oil and grease only one type of lubrication should be used at any one time) A high-pressure hand pump gun is available from Cogsdill to make routine maintenance easy (Ref Part No CN-D24) Actuation Ratios The standard actuation ratio for our heads is based on a 40-degree actuation angle Slide travels for the standard actuation ratio are shown in the specification charts on the following pages Special actuation ratios are available to accommodate unique applications (eg, when an extremely short tool stroke is required) Please consult with our engineering group when a non-standard ratio is required Adapter Plates The bolt pattern in Cogsdill generating heads will fit a variety of spindles However, when using a standard head, it may be necessary to use an adapter plate to mount the head due to different bolt patterns in the head and spindle Cogsdill can design and manufacture adapter plates, when needed, to ensure accurate mounting of the head on any spindle Special bolt patterns can also be built into specially designed heads Top Tooling Packages/Counterbalance Weights Cogsdill can provide full top tooling packages for your application Standard ISO / ANSI inserts are used where possible Special form inserts are supplied where required When using a double-slide head, the slides move in opposing directions This allows the head to be balanced by mounting a counterbalance to the slide opposite the one with the cutting tool The weight moves proportionately to the cutting edge, thus producing a balanced cut (In doubleslide applications where tooling is mounted on both slides, the tooling can be balanced) Balance is particularly important as the size of the head, or the rotational speed, increases The head can be dynamically balanced to a specific cut diameter and speed (Single-slide heads are generally not balanced) 58 Lubrication Recommendations

59 Features & Options Generating HEADS (continued) Drawbar Force Requirements The drawbar force required to actuate the generating head is dependent upon three variable but interrelated factors: Size of generating head Spindle speed or cycle time requirement Weight of top tooling As the size of the head increases, so does the required drawbar force Cycle time requirements can also directly affect the spindle speed In some cases, the use of high strength aluminum alloy cross slide(s) and/or top tooling may be necessary to keep the drawbar force requirements within the operational limits of the machine (see next section below) Due to variations in top tooling weight, it is difficult to predict the actual drawbar force required to operate a generating head in a given application until a thorough layout is completed When submitting a generating head application for quotation, please provide the following information in addition to part prints and general machine specifications: Spindle speed range available for your machine Desired cycle time (if known) for the operation(s) to be performed Drawbar actuation method (ie mechanical, CNC, or hydraulic) and force available Our engineering department will recommend the appropriate generating head, and will quote a complete tooling package to suit your requirements Lightweight Cross Slides and Top Tooling When application requirements demand head operation at higher than normal speeds, Cogsdill engineers can specify a special lightweight, high strength, aluminum alloy for manufacturing cross slides and some top tooling The use of this alloy reduces the rotational mass of the head, allowing the tool to be run at higher speeds without significantly affecting the drawbar force requirement for actuating the head Requests for Quotation All quote requests should be submitted through our customer service department While most heads sold are standard heads, each application tends to be unique In order for our engineers to prepare a formal and complete quotation, we need to know as much as possible about your application In order to assure that we have the necessary data for quoting, please submit the following: A copy of the Application Data Sheet in the back of this catalog, filled out as completely as possible (material type, operations required, how the parts will be fixtured, etc) A complete part drawing, and machine and spindle data Please include spindle speed range, drawbar actuation method, and available drawbar force (if known) Other important information includes: Does the application require a head that feeds in or feeds out? What actuation ratio is required (if known)? (If unknown, our engineers will gladly make recommendations) Single or double slide? What type of drawbar fitting? (Ie male or female, thread size and pitch Male is standard, female is available on request) Is through-lube capability available on the machine spindle? What is your production volume requirement? What is the desired machining cycle time for the operations involved (if known)? Our customer service personnel will be pleased to assist you in answering questions about your application 59

60 Specifications Generating HEADS Single-Slide Head ØA M x P ØN ØH ØG ØF L 2 R 4 retaining screws W x P on an X bolt circle K L1 Mounting holes Q x P 1 C T Drive dowel øu on V radius J B D E Z max actuator stroke S R Y max slide stroke STD 40 M x P ØN Optional female fitting actuator (non-standard) INCH [METRIC] HEAD TYPE (A) (B) (C) (D) (E) (F h5 ) (G) (H) (J) (K H7 x DP) (L1) (L2) CN100SA CN125SA CN160SA CN200SA CN250SA 3937 [100] 4921 [125] 6300 [160] 7874 [200] 9843 [250] 1969 [50] 2283 [58] 2756 [70] 3346 [85] 3937 [100] 0236 [6] 0315 [8] 0374 [95] 0472 [12] 0591 [15] 1772 [45] 1969 [50] 2362 [60] 2756 [70] 3543 [90] 0394 [10] 0394 [10] 0394 [10] 0394 [10] 0394 [10] 1260 [32] 1772 [45] 3937 [100] 5315 [135] 6300 [160] 0984 [25] 1181 [30] 1378 [35] 1969 [50] 1969 [50] 0630 [16] 0787 [20] 0984 [25] 1260 [32] 1260 [32] 1181 [30] 1575 [40] 1969 [50] 2756 [70] 3543 [90] 0315 x 0118 [8 x 3] 0315 x 0118 [8 x 3] 0394 x 0157 [10 x 4] 0472 x 0157 [12 x 4] 0472 x 0157 [12 x 4] 0669 [17] 0984 [25] 1181 [30] 1772 [45] 2362 [60] 0433 [11] 0512 [13] 0630 [16] 0787 [20] 0787 [20] INCH [METRIC] HEAD TYPE (M x P/LH) (N h7 ) (Q x P) (R) (S) (T) (U m5 ) (V) (W x P) (X) (Y) (Z) CN100SA CN125SA CN160SA CN200SA CN250SA M10 x 10 M10 x 10 M12 x 15 M16 x 15 M16 x [12] 0551 [14] 0709 [18] 0709 [18] 0709 [18] M5 x 08 M6 x 10 M8 x 125 M10 x 15 M12 x [8] 0315 [8] 0394 [10] 0394 [10] 0394 [10] 0669 [17] 0748 [19] 0984 [25] 0984 [25] 0984 [25] 0197 [5] 0236 [6] 0256 [65] 0394 [10] 0472 [12] 0315 [8] 0394 [10] 0472 [12] 0630 [16] 0787 [20] 1575 [40] 1969 [50] 2559 [65] 3346 [85] 3937 [100] M8 x 125 M10 x 150 M12 x 175 M12 x 175 M16 x [70] 3543 [90] 4724 [120] 6300 [160] 7480 [190] 0669 [17] 0866 [22] 1181 [30] 1575 [40] 1969 [50] 0795 [202] 1031 [262] 1406 [357] 1878 [477] 2346 [596] 60

61 Bill of Materials Generating HEADS Single-Slide Head Cross-slide 7 Keeper Plate 13 Caphead Screw 19 Location Dowel 2 Slide Block 8 Slide Block 14 Grease Nipple 24 Spring Washer 3 Body 9 Locknut 15 Dog Point Screw 4 Key 10 Drive Dowel 16 Head Screw 5 Actuator 11 Lock Screw 17 Spring Plunger 6 Key 12 Caphead Screw 18 Wiper 61

62 Specifications Generating HEADS Double-Slide Head X2 X1 ØA M x P ØN ØH ØG L2 R S ØF K J Mounting holes Q x P 1 C T Drive dowel øu on V radius L1 4 retaining screws W x P Y max slide stroke Y max slide stroke 40 Z max actuator stroke 40 B Optional female fitting actuator (non-standard) D E S R M x P ØN INCH [METRIC] HEAD TYPE (A) (B) (C) (D) (E) (F h5 ) (G) (H) (J) (K H7 x DP) (L1) (L2) CN100DA CN125DA CN160DA CN200DA CN250DA 3937 [100] 4921 [125] 6300 [160] 7874 [200] 9843 [250] 1969 [50] 2283 [58] 2756 [70] 3346 [85] 3937 [100] 0236 [6] 0315 [8] 0374 [95] 0472 [12] 0591 [15] 1772 [45] 1969 [50] 2362 [60] 2756 [70] 3543 [90] 0394 [10] 0394 [10] 0394 [10] 0394 [10] 0394 [10] 1260 [32] 1772 [45] 3937 [100] 5315 [135] 6300 [160] 0984 [25] 1181 [30] 1378 [35] 1969 [50] 1969 [50] 0630 [16] 0787 [20] 0984 [25] 1260 [32] 1260 [32] 0630 [16] 0787 [20] 0984 [25] 1260 [32] 1772 [45] 0236 x 0118 [6 x 3] 0315 x 0118 [8 x 3] 0315 x 0118 [8 x 3] 0315 x 0118 [8 x 3] 0394 x 0157 [10 x 4] 1102 [28] 1339 [34] 1772 [45] 2126 [54] 2756 [70] 0394 [10] 0512 [13] 0630 [16] 0787 [20] 0787 [20] INCH [METRIC] HEAD TYPE (M x P/LH) (N h7 ) (Q x P) (R) (S) (T) (U m5 ) (V) (W x P) (X1) (X2) (Y) (Z) CN100DA CN125DA CN160DA CN200DA CN250DA M10 x 10 M12 x 15 M16 x 15 M16 x 15 M16 x [12] 0551 [14] 0709 [18] 0709 [18] 0709 [18] M6 x 10 M8 x 125 M8 x 125 M8 x 125 M10 x [8] 0315 [8] 0394 [10] 0394 [10] 0394 [10] 0669 [17] 0748 [19] 0984 [25] 0984 [25] 0984 [25] 0197 [5] 0236 [6] 0256 [65] 0394 [10] 0472 [12] 0315 [8] 0394 [10] 0472 [12] 0630 [16] 0787 [20] 1575 [40] 1969 [50] 2559 [65] 3346 [85] 3937 [100] M8 x 125 M10 x 15 M12 x 175 M12 x 175 M16 x [46] 2087 [53] 2520 [64] 4016 [102] 5000 [127] 2441 [62] 2992 [76] 3937 [100] 4409 [112] 5984 [152] 0669 [17] 0866 [22] 1181 [30] 1575 [40] 1969 [50] 0795 [202] 1031 [262] 1406 [357] 1878 [477] 2346 [596] 62

63 Bill of Materials Generating HEADS Double-Slide Head Cross-slide 9 Locknut 15 Dog Point Screw 23 Keeper Plate 2 Slide Block 10 Drive Dowel 16 Head Screw 24 Spring Washer 3 Body 11 Lock Screw 17 Spring Plunger 4 Key 12 Caphead Screw 18 Wiper 5 Actuator 13 Caphead Screw 19 Location Dowel 7 Keeper Plate 14 Grease Nipple 20 Set Screw 63

64 Applications Generating HEADS 125mm (approx 5 in) Single-Slide Feed-Out Head machining three chamfers in one pass 160mm (approx 625 in) Double-Slide Feed-In Head machining aluminum barb end fitting complete in one pass BACK TURNING 64

65 Applications Generating HEADS 200mm (approx 8 in) Single-Slide Feed-Out Head machining boot groove in brake caliper 100mm (approx 4 in) Double-Slide Generating Head machining spherical radius 65

66 Applications Generating HEADS 250mm (approx 10 in) Double-Slide Feed-In Head performing ten operations: three faces, three grooves, and four chamfers 250mm (approx 10 in) Double-Slide Feed-Out Head performing ten operations on an aluminum housing: three grooves, five chamfers, and two faces 160mm (approx 625 in) Double-Slide Feed-Out Head performing six operations: three grooves, one face, one chamfer, and one ID turning operation 66

67 overview Precision Chamfering Nobur JB Series For back-chamfering or deburring on drill presses, CNC machines, tool or turret lathes, multi-spindle machines and jig boring machines Consistently accurate back-chamfering, deburring, and back-countersinking operations Pilots in hole for precise concentricity Rigid support of the cutter virtually eliminates deflection Micrometer-stop adjustment Standard pilots and cutters for hole sizes from 3/16 to 3/4 (475 to 1905mm) Special pilots and cutters available upon request 67

68 Operating Principle Nobur JB Series AUTOMATIC BACK-CHAMFERING Illustrated below is the basic operating principle for the Nobur JB Automatic Back-Chamfering tool 1 Approach Stroke The Nobur JB tool is rotating in a machine spindle The spindle is lowered to bring the tool into position to enter the bore 2 Feed Stroke The pilot locates in the bore, stopping against the face of the workpiece As the spindle continues to travel, the tool is compressed so that the cutter feeds out radially into the work The cutter is rigidly supported in the bore by the pilot to eliminate deflection and ensure concentricity 3 End of Feed Stroke Radial depth of cut is obtained when the micrometer-stop nut bottoms out Chamfer location is controlled by rotation of the stop collar, which moves the stop collar extension up or down to position the cutter for accurate chamfer location 68

69 Specifications Nobur JB Series AUTOMATIC BACK-CHAMFERING 125 ø B ø FREE 1/2-1 ( MM) RANGE MATERIAL THICKNESS WITHOUT STOP COLLAR EXTENSION STOP COLLAR EXTENSION 1/32-1/2 ( MM) RANGE MATERIAL THICKNESS WITH STOP COLLAR EXTENSION INCH [METRIC] CAPACITY * IN MM IN 078 (A) MAX MM 198 (B) SHANKS ** STRAIGHT SHANKS 1/4 3/8 w/tang The Feed Ratio is the ratio of vertical to horizontal movement The Maximum Feed Stroke is 038 in (94mm) * Capacity means the suggested maximum chamfer diameter Dependent upon cutting forces and bore diameter Stated capacity is for steel Shank is included with head Shanks other than shown can be supplied upon request ** 69

70 Bill of Materials Nobur JB Series AUTOMATIC BACK-CHAMFERING 1 Body Holder 5 Retaining Ring 9 Compression Spring 15 Pilot 2 Stop Nut 6 Ball Thrust Bearing 10 Ball (19/64) diameter 16 Blade 3 Stop Collar 7 Bearing Cage 11 Pilot Retaining Screw 4 Keyed Transport Sleeve 8 Transport Assembly 12 Stop Collar Extension 70

71 CNF Series PRECISION CHAMFERING CNF Precision Chamfering Cogsdill CNF Series Precision Chamfering tools produce controlled chamfers on both sides of drilled or reamed holes Designed for high production, these highly accurate tools require only one pass to generate consistent chamfers on the front and back of holes Features: Fast cycle times Available with high-speed steel or solid carbide cutters for diameters from 0059 to 0390 inch (150 to 990mm) Tools for diameters of 10mm or larger use standard replaceable ISO inserts CNF1 shown here with automotive-style shank All shank styles are available to suit the application please specify when ordering 71

72 Operating Principle CNF Series PRECISION CHAMFERING Illustrated below is the basic operating principle for the CNF Precision Chamfering tool Piloting The tool diameter pilots into the hole up to the pre-formed cam opposite to the cutting edge 2 Actuation The tool travels forward and is actuated by the cam, generating the back chamfer 3 Chamfering The tool continues to travel forward, forming the top chamfer 72

73 Specifications CNF Series PRECISION CHAMFERING 'A' 'D' ø'b' ø'c' CNF 1 & CNF 2 'D' ø'c' CNF 3 INCH [METRIC] HEAD TYPE CNF1 CNF2 CNF3 PART DIAMETER [ ] [ ] [ ] [ ] [ ] CAPACITY RANGE MAXIMUM CHAMFER 0030 [08] 0080 [20] 0080 [20] CUTTER TOOLHOLDER DESIGN HSS or TCT ISO inserts HSS or TCT ISO inserts ISO inserts MAXIMUM FLOAT 0059 [15] 0118 [30] 0118 [30] SHANKS 16mm DIA 20mm DIA 20mm DIA (A) FREE LENGTH 173 [440] 185 [470] 185 [470] (B) TOOL BODY ø126 [ø320] ø197 [ø500] ø197 [ø500] (C) CUTTER SHANK 0394 [100] 0394 [100] 0630 [160] (D) REF MIN CUTTER LENGTH 098 [250] 098 [250] 098 [250] 73

74 Bill of Materials CNF Series PRECISION CHAMFERING CNF A Front Bush 6 Spacer 11 Ball 16 Cage 2 Set Screw 7 Inner Body 12 Guide Bush 17 Dowel 3 Lock Nut 8 Ball 13 Dowel 18 Thrust Washer 4 Shank 9A Cage 14 Ball 19 Dowel 5 Set Screw 10 Selloc Pin 15 Spring 74

75 Bill of Materials CNF Series PRECISION CHAMFERING CNF2 9A SECTION VIEW Front Bush 7 Inner Body 12 Guide Bush 18 Thrust Washer 2 Set Screw 8 Ball 13 Dowel 19 Dowel 3 Lock Nut 9A Cage 14 Ball 4 Shank 10 Selloc Pin 15 Spring 5 Set Screw 11 Thrust Brg 17 Dowel 75

76 Bill of Materials CNF Series PRECISION CHAMFERING CNF3 9A SECTION VIEW Front Bush 7 Inner Body 12 Guide Bush 18 Thrust Washer 2 Set Screw 8 Ball 13 Dowel 19 Dowel 3 Lock Nut 9A Cage 14 Ball 4 Shank 10 Selloc Pin 15 Spring 5 Set Screw 11 Thrust Bearing 17 Dowel 76

77 Applications Nobur JB & CNF Series PRECISION CHAMFERING Nobur JB Tool back-chamfers both sides of holes in large single-speed gear ring 06336±00005 [16093±0013] PILOT ø 0375 [95] ø138 [35] 619 [157] Nobur JB Tool deburrs back side of yoke 77

78 Applications Nobur JB & CNF Series PRECISION CHAMFERING CNF1 Tool machining front and back chamfer on automotive component STAGE 1 STAGE 2 STAGE 3 78

79 Applications Nobur JB & CNF Series PRECISION CHAMFERING CNF3 Tool performing front and back-chamfering operation using tool with modular holder STAGE 1 STAGE 2 STAGE 3 79

80 Applications Nobur JB & CNF Series PRECISION CHAMFERING CNF1 Tool machining back chamfer on differential housing STAGE ONE STAGE TWO 80

81 Applications Nobur JB & CNF Series PRECISION CHAMFERING CNF1 Tool machining back-chamfer with undercut CNF1 Tool boring groove with chamfer on each end of small bore 81

82 Application Data Sheet Automatic Recessing GENERATING HEADS & PRECISION CHAMFERING To ensure that the correct tool is furnished for your particular application, please photocopy, complete this data sheet, and enclose it with your order or request for quotation This is a requirement for ALL recessing applications, including internal and external facing, chamfering, and back-spot facing, as well as grooving Customer Information Date Quote No Customer Address City State Zip Attn Phone Fax Sales Agent/Distributor Application Specifications 1 Machine make/type 2 Shank style If shank is threaded for retention knob or drawbar, specify thread size 3 Groove diameter (B) 4 Groove width (W) 5 Groove to face dimension (L) 6 Bore diameter (A) / Groove depth (D) 7 Is surface finish required in groove? If yes, specify 8 Material Type and condition 9 Are there any restrictions? Length Diameter Rotating If there is a weight limit, please specify Used in a tool changer? Yes No 10 Is tool running: Horizontal Vertical Stationary 11 Is recessing tool to be used with a fixture? Yes No If yes, full layout drawings must be attached or sketched 12 How is part to be held or clamped? 13 What type of feed will be used? Hand Power 14 Desired coolant feed: External Internal through spindle Internal with rotating collar 15 If SPC or CPK applies, please specify (continued on next page)

83 Application Data Sheet Automatic Recessing GENERATING HEADS & PRECISION CHAMFERING (continued) Additional Comments IMPORTANT PART PRINT OR DETAILED SKETCH MUST BE SUPPLIED Please indicate location of grooves or recesses, dimensions, tolerances, and direction of tool approach In multiple groove applications, supply (L), (W) and (B) dimensions for each groove (øa) (D) (L) TOOL APPROACH BORE (øb) (W) FAX MAIL Cogsdill Tool Products, Inc PO Box 7007 Camden SC Attn: Sales Department

84