Submersible Turbine Assembly Manual

Size: px

Start display at page:

Download "Submersible Turbine Assembly Manual"

Solomon Watson
5 years ago
Views:

1 Submersible Turbine Assembly Manual

2 Table of Contents Submersible Turbine Kit Assembly Page Recommended Equipment... 2 Assembly Instructions Special Tool Schematics Symbol Key Action Safety/Caution Verify

3 Recommended Equipment Machinery & Tools: The minimum basic hand tools and equipment needed for submersible turbine assembly: Assembly Fixture Kit (See special tools section, pg for additional information) 5 x 5/6 x 6 Collet Hammer x 6/8 x 8 Collet Hammer Allen Wrenches SAE or Standard (preferably T-handle design) 5/32" is used for sand collar set screws 1/8" is used for motor coupling set screws 3/8" for STS upthrust adjustment Combination wrench or socket and ratchet set 5/16" for cable guard screws 7/16" for 6" sub turbine bowl bolts 9/16" for 8" sub turbine bowl bolts 1-1/8" for upthrust lock nut Flat head or standard large screwdriver Ballpeen hammer Set of 1/8" stamps for imprinting nameplate information and date code Dow Corning 111 Valve Lubricant & Sealant (food grade grease) Loctite 243 Fine emery cloth or steel wool for de-burring purposes. Additional machinery and/or equipment will be required if the assembler desires the ability to cut and de-burr shafting and cable guards or remove and install bronze bearings. Optional tool available: " or 6" STS Bowl Bolt Assembly Tool " STS Bowl Bolt Assembly Tool 2

Assembly Instructions 1 Place bracket on vertical build fixture.

Bronze bearing pre-installed into motor bracket. 1 2 Inspect shaft straightness.

Shaft straightening should be done mechanically without using heat.

Shafts offered cut to length for standard stage counts and as double keyed sections in lengths of 4', 6', 8'

4 Assembly Instructions 1 Place bracket on vertical build fixture. Note: See Special Tool Section (pages 10-11) for fixture dimensions. Bronze bearing pre-installed into motor bracket. 1 2 Inspect shaft straightness. Pump shaft must be straight to within 0.002" total indicator runout (TIR) when shaft is supported at each end. Shaft straightening should be done mechanically without using heat. Note: If shafts are cut to length be sure cut is square and chamfer end. Shafts offered cut to length for standard stage counts and as double keyed sections in lengths of 4', 6', 8' and 10'. 2 3 Tip assembly over and tighten fixture bolt with wrench hand-tight. Note: See Special Tools Section (pages 10-11) for fixture bolt size. 3 4 Apply Loctite 243 to set screws of sand collar. Thread set screws into sand collar. Make sure set screws do not stick out into ID of sand collar. 4 3

Assembly Instructions 5 Install sand collar onto shaft and push over bracket bearing

6 7 Install impeller onto shaft and position bottom against bracket/bowl.

A flat screwdriver may be needed to spread collet while sliding.

largest impeller diameter, A-Trim, followed by the B-Trim, and ending with the C-Trim

5 Assembly Instructions 5 Install sand collar onto shaft and push over bracket bearing until seated. 5 6 Tighten sand collar set screws to lb-in. 6 7 Install impeller onto shaft and position bottom against bracket/bowl. Slide collet onto shaft and position into impeller. A flat screwdriver may be needed to spread collet while sliding. Note: When using a mix of impeller trims, always start the sub turbine build with the largest impeller diameter, A-Trim, followed by the B-Trim, and ending with the C-Trim impellers. 7 8 Drive collet into impeller using the collet drive hammer. Collet will not drive flush. Continue to hammer collet until impeller is secure on sub turbine shaft. 8 4

Assembly Instructions 9 10 11 Slide bowl onto shaft. Note: For 6" STS, please align cable guard indentions on outside of bowl.

6" STS: Torque bolts to 10-12 lb-ft. Stages 1 thru 9 will receive 8 bolts.

Note: For 100 gpm 6" STS pumps longer than 13 stages, after installing the 10th bowl, use three.

After bowl bolts are snug, install the impeller and collet. Next, remove the shims and tighten the bowl bolts normally.

6 Assembly Instructions Slide bowl onto shaft. Note: For 6" STS, please align cable guard indentions on outside of bowl. Secure bowl with bowl bolts (Impact or torque wrench recommended). 5" STS: Torque bolts to lb-ft. All stages will receive 12 bolts. 6" STS: Torque bolts to lb-ft. Stages 1 thru 9 will receive 8 bolts. The top of stage 9 and higher will receive 14 bolts due to the use of XP bowls. Note: For 100 gpm 6" STS pumps longer than 13 stages, after installing the 10th bowl, use three.030 shims between the next set of bowls as depicted in the picture. Tighten bowl bolts to snug. After bowl bolts are snug, install the impeller and collet. Next, remove the shims and tighten the bowl bolts normally. Repeat shimming procedure for all remaining stages until all impellers are installed. 8" STS: Torque bolts to lb-ft. Stages 1 through 12 will receive 8 bolts. The top of stage 13 and higher will receive 16 bolts due to the use of XP bowls. Repeat process from Step 7 thru 10 for all stages up to last bowl. Do not install an impeller between last bowl and discharge bracket Note Press top bearing into top bowl assembly. 12 5

Assembly Instructions 13 Fill discharge 1/4 full

13 14 Attach discharge with bolts as in steps 10-11.

discharge are lined up with the cable guard holes on

14 15 Lift pump with proper support and lay down

7 Assembly Instructions 13 Fill discharge 1/4 full with Dow Corning 111 grease Attach discharge with bolts as in steps " & 8" STS: ensure the cable guard holes on the discharge are lined up with the cable guard holes on the motor bracket Lift pump with proper support and lay down horizontal. CAUTION: Prevent from rolling Remove fixture bolt from pump shaft. Use impact wrench as necessary. 16 6

Assembly Instructions 17 Place key on pump

18 19 Slide coupling onto shaft, aligning

8 Assembly Instructions 17 Place key on pump shaft as shown Apply Loctite 243 to the motor coupling set screws. Install set screws so they are clear of the keyway Slide coupling onto shaft, aligning key, until seated Tighten set screws onto key. Torque Values: 5x6, 6x6, and 8x6 = lb-in. 8x8 = lb-in. 20 7

Assembly Instructions 21 Apply a small bead of Loctite 243 to upthrust bolt.

and discharge bearing housing. 5" or 6" STS - Spacer thickness = 0.

250" 23 Note: An alternative procedure to using the spacer is to back out the 5" or 6"

9 Assembly Instructions 21 Apply a small bead of Loctite 243 to upthrust bolt Install upthrust bolt in discharge until contact is made with top of shaft and all downplay is taken up Unscrew bolt and nut together until upthrust spacer can be installed between nut and discharge bearing housing. 5" or 6" STS - Spacer thickness = 0.221" 8" STS - Spacer thickness = 0.250" 23 Note: An alternative procedure to using the spacer is to back out the 5" or 6" STS upthrust bolt 2 1/4 turns or the 8" STS upthrust bolt 2 1/2 turns, then secure the position by tightening the lock nut. 24 Remove spacer and tighten lock nut against discharge, holding bolt constant with no rotation. 24 8

Assembly Instructions 25 Install nameplate onto bracket.

picture. 6" STS: Install cable guard using supplied screws.

10 Assembly Instructions 25 Install nameplate onto bracket Install suction screen using supplied drive screws Cable guard installation. 5" STS: Install cable guard using supplied screws and cable clamp. Torque screws to lb-in. Install cable clamp between the discharge and top bowl, as noted in picture. 6" STS: Install cable guard using supplied screws. Torque screws to lb-in. 8" STS: Install cable guard using supplied screws. Torque screws to lb-in. NOTE: 6" motor installations require 8x6 transition piece ( ). 27 9

11 Special Tools Collet Hammer Tools 5x6, 6x6 Part # x6, 8x8 Part # Knurl this area to within 0.5 of each shoulder Knurl this area to within 0.5 of each shoulder

12 Special Tools Assembly Fixture Kit # Note: Kit includes 5x6, 6x6, 8x8 Assembly Fixture, 8x6 Assembly Plate. Plate Screws, and Shaft Bolts. 5x6, 6x6, and 8x8 Assembly Fixture Note: Use 3/8-16 UNC -x 4" long bolt to hold shaft for 5" or 6" turbine assembly. Use 3/8-16 UNC -x 4-1/2" long bolt to hold shaft for 8" turbine assembly. 5" or 6" Upthrust Spacer 8" Upthrust Spacer Part # Part # Note: An alternative procedure to using the spacer is to back out the 5" or 6" STS upthrust bolt 2 1/4 turns or the 8" STS upthrust bolt 2 1/2 turns, then secure the position by tightening the lock nut. 11

13 Special Tools Assembly Fixture Kit # Note: Kit includes 5x6, 6x6, 8x8 Assembly Fixture, 8x6 Assembly Plate. Plate Screws and Shaft Bolts. 8x6 Assembly Plate Note: Use 3/8-16 UNC -x 4" long bolt to hold shaft for 5" or 6" turbine assembly. Use 3/8-16 UNC -x 4-1/2" long bolt to hold shaft for 8" turbine assembly. 12

14 13 Notes

15 Notes 14

16 TOLL FREE HELP FROM A FRIEND FAX Phone Franklin s toll free SERVICE HOTLINE for answers to your pump and motor installation questions. When you call, a Franklin expert will offer assistance in troubleshooting and provide immediate answers to your system application questions. Technical support is also available online. Visit our website at: Coverdale Road, Fort Wayne, IN Tel: Fax: Mi

INSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE

INSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE DENTAL, INC. TECHNICAL BULLETIN Q824-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427 SAVE THIS FOR FUTURE REFERENCE www.wellsdental.com