Butt Two pieces of wood meeting with flat sides adjoining usually at right angles. Some type of connector is needed to prevent movement.
|
|
- Felix Sanders
- 5 years ago
- Views:
Transcription
1 Wood Connections There are basically five different types of connectors: Interlocking (carpentry joints), Dowel, Metal Connectors, Special Formed Connectors and Adhesives. I Interlocking (Carpentry Joints) Mortise and Tenon The most common traditional timber joint, the mortise is a slot made into a member that receives the tenon, a projecting tongue of wood on the end of the connecting member. Pegs, small dowels inserted into holes that pass through the mortise and tenon of each member, act to prevent movement at the joint. This type of joint creates only a post and beam type of connection; no resistance to rotation and hence stability is provided. There are many variations of the basic mortise and tenon joint. Wedged dovetail tenon Stub tenon joint Bridle scarf and side-halved scarf Butt Two pieces of wood meeting with flat sides adjoining usually at right angles. Some type of connector is needed to prevent movement. Butt joint with dowels Butt joint with biscuit Butt joint with screws or nails
2 Miter or mitre Two pieces of wood meeting at right angles with each piece cut at 45º. Lap A very common type of joint in which a portion of each connecting member is removed in order to create a flush interlocking connection. Some type of connector (dowel, glue, screw, etc.) is required to prevent movement. Halving joint Finger A strong joint that creates a flush connection. II Dowel Staples Useful to fix thin panels or other materials to a wood frame.
3 Nails Most widely used dowel-type fastener. Many types of nails of different sizes, shapes and materials (steel, galvanized, etc.). Each nail has a specific strength in shear. The number of nails required depends on the total shear transfer between the connected members. A smooth or shank profile nail is the most basic. Nails with annular rings are called threaded nails and have improved withdrawal strength. Screws Larger and with greater strength than nails. Used in smaller number than nails. Can be used to connect wood to wood or metal to wood. Most common types are: countersunk head screw, round head screw and coach screw. Coach screw (countersunk) Wood screw (countersunk) Bolts Threaded dowel-type fasteners designed to be fitted with a nut to prevent pullout. Strongest of dowel-type fasteners and larger in cross section. Common types are: hexagonal head bolt, square head bolt and carriage bolt. Hexagonal head bolt Carriage bolt Dowels Plain, circular rods that are fitted snuggly into drilled holes. They transfer load entirely by shear.
4 III Metal Connectors Metal plates 2D Metal plates are typically flat plates that lap across two pieces of wood to be connected and rely on the shear resistance of both the metal plate and the nails that penetrate into the wood members. Plates can have holes into which are driven nails, or they may be formed in which case the nail is incorporated as part of the metal plate. These are often referred to as nailing plates. Metal plate with holes Punched metal plate fastener with teeth Metal Plates 3D Three-dimensional metal plates are formed to facilitate connections between wood members. Common types are: joist hangers, truss clips and brace anchors. These are provided by various manufacturers. Joist hanger Truss clip Anchorage for brace Connectors with bolts Metal conectors with bolts are usually hidden within the wood member. There are three types: split-ring, shear-plate and toothed-plate. Split-ring connector
5 Shear-plate connector Toothed-plate connector Metal Gusset Plates Mainly used for connecting multiple members together in a truss, Can have a wide variety of shapes to fit the geometry of the joint. Can be bolted or screwed. IV Special Formed Connectors Nodal connector Nodal connectors are specially designed metal components that conform to the geometry of the desired connection. They can be fabricated from plate steel or alternatively, formed from casting. A complex nodal connector of interlocking steel plates A pin-type connector of welded plate
6 Cast steel pin-type connector
7 V Adhesives Adhesively bonded connections All engineered lumber products use adhesives for the manufacture of panels (plywood, particle board, strand board, etc.), laminated lumber (glulam, LVL, PSL, LSL, etc.) and for special sectional components: timber I-joists, box beams and stressed skin panels. Resin-anchored bolts Adhesives applied to a bolted connection to improve the performance of the overall connection. Glued gusset plates Plywood gusset plates can be connected with adhesive replacing nails.
Dowel-type fasteners. Timber Connections. Academic resources. Introduction. Deferent types of dowel-type fasteners. Version 1
Academic resources Timber Connections Dowel-type fasteners Version 1 This unit covers the following topics: Deferent types of dowel-type fasteners Introduction There are four criteria designers should
More informationeb^sv=qfj_bo UNIVERSITY OF WISCONSIN - STOUT COLLEGE OF SCIENCE TECHNOLOGY ENGINEERING & MATHEMATICS Architectural Technology AEC 233
eb^sv=qfj_bo UNIVERSITY OF WISCONSIN - STOUT COLLEGE OF SCIENCE TECHNOLOGY ENGINEERING & MATHEMATICS Architectural Technology AEC 233 Dr. Jason E. Charalambides fkqolar`qflk Heavy timber construction consists
More informationActivity Joinery, Fastener, Adhesive, Welding & Bonding Identification
Name: Date Completed: Activity 3.3.1 Joinery, Fastener, Adhesive, Welding & Bonding Identification Introduction When you look at a fine piece of furniture, such as a chair with many different parts, it
More informationDesign and Manufacture JOINING
Design and Manufacture JOINING Introduction Different materials require different tools. These tools and joints are used when joining wood: Finger Dovetail Housing Dowel Cross halving Corner Lap Mortise
More informationMaterials, tools and processes
Materials, tools and processes Extension material for Level 1 Design and Visual Communication Study Guide ISBN 978-1-877459-02-3, Page 153 Tools Tools are used to work materials to improve their appearance,
More informationSections & Details VOCABULARY
1 Sections & Details VOCABULARY 1 ROOF FRAMING DETAIL RIDGE BOARD SHEATHING SHINGLES WEB FASCIA RAFTER (chord) SOFFIT SHEATHING STUD INSULATION DOUBLE TOP PLATE CEILING JOIST 2 FOUNDATION DETAIL STUD SHEATHING
More informationConnection Solutions for Wood-frame Structures. Copyright Materials. Learning Objectives
Connection Solutions for Wood-frame Structures Presented by: John Buddy Showalter, P.E. Vice President, Technology Transfer The Wood Products Council is a Registered Provider with. Credit(s) earned on
More informationThe Wood Products Council is a Registered Provider with. . Credit(s) earned on completion of this program will be
Connection Solutions for Wood-frame Structures Presented by: John Buddy Showalter, P.E. Vice President, Technology Transfer The Wood Products Council is a Registered Provider with. Credit(s) earned on
More informationjoining materials - wood
UNIT D E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L Wood joints joining materials - wood The majority of joints used in woodcraft have been designed specifically to attain the maximum
More informationA Shell construction
A Shell construction A 4/2012 Content 1 BASE AND WALL ANCHORING 1.1 Base with mortar bed 1.2 Base with sill plate 1.3 Base with raised sill plate 1.4 Concrete base (mortar bed) 1.5 Concrete base (sill
More informationSTRUCTURAL TIMBER DESIGN
STRUCTURAL TIMBER DESIGN to Eurocode 5 2nd Edition Jack Porteous BSc, MSc, DIC, PhD, CEng, MIStructE, FICE Director lack Porteous Consultancy and Abdy Kernlani BSc, MSc, PhD, CEng, FIStructE, FIWSc Professor
More informationFastener Type Chart. Fastener Categories. Sheet Metal Screws Fully threaded screws with a point for use in sheet metal. Abbreviated SMS.
Fastener Categories Wood Screws Machine Screws Thread Cutting Machine Screws Screws with a smooth shank and tapered point for use in wood. Abbreviated WS. Screws with threads for use with a nut or tapped
More informationDescription. Lesson Outcomes. Assumptions. Build a Floor. Carpenter
Carpenter Description Floors are an integral part of residential construction and must be built to specifications that meet building code requirements. In this Activity Plan, students will be cutting and
More informationConnections in CLT Assemblies
Creating forest sector solutions www.fpinnovations.ca Connections in CLT Assemblies Cross Laminated Timber Symposium Vancouver, BC February 8-9, 2011 M. Mohammad Building Systems Wood Products Division
More informationFASTENERS BUILDING DEPARTMENT
FASTENERS BUILDING DEPARTMENT 952-446-1660 WWW.CITYOFMINNETRISTA.COM This handout is intended only as a guide and is based in part on the 2015 Minnesota Residential Code, Minnetrista City ordinances, and
More informationIndustry Related Manufacturing Technology
Industry Related Manufacturing Technology Focus Area: Timber Products and Furniture Technologies (Preliminary) Materials Timber and timber products structure: sapwood heartwood earlywood latewood cambium
More informationWood Connections. Presented by: Karyn Beebe, P.E.
Wood Connections Presented by: Karyn Beebe, P.E. Key to Connections 1. Wood has a strong and weak direction 2. Wood Moves 3. Strive for Consistency 4. Wood and Moisture Don t Mix 5. Load Path Continuity
More informationSections & Details. WOOD SILL and FLOOR CONSTRUCTION NOTES
2 Sections & Details WOOD SILL and FLOOR CONSTRUCTION NOTES 1 Commonly Used Lumber Common LENGTHS include: 8, 10, 12, 14, 16 NOMINAL SIZES 2 x 4 2 x 6 2 x 8 2 x 10 2 x 12 ACTUAL SIZES 1 ½ x 3 ½ 1 ½ x 5
More informationBauBuche Fasteners and connections
BauBuche Fasteners and connections Beech laminated veneer lumber Chapter under revision 05 BauBuche Fasteners and connections 05 04-18 - EN Sheet 1 / 10 Fasteners and connections Sheet CONTENTS 2 3 4 9
More informationFramework joints FABRICATION - WOOD JOINTS. Corner joints. Tee joints. Worksheet 15a. Cable Educational Ltd
FABRICATION - WOOD JOINTS The word: fabricate means to join together. Most wooden products are held together with adhesive. Adhesive works very well when the edge of a piece of wood is being glued to the
More informationTOLL FREE:(888) FAX:(941) ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL
ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL The ProTEC panels are manufactured with grooves on all four sides to accept the steel components. This grooving applies to the regular panel whose
More informationSECTION CONCRETE ANCHORING. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 03 15 00 CONCRETE ANCHORING Display hidden notes to specifier. (Don't know how? Click Here) A. General purpose mechanical anchors for horizontal and vertical
More informationMoment-Resisting Connections In Laminated Veneer Lumber (LVL) Frames
Moment-Resisting Connections In Laminated Veneer Lumber (LVL) Frames Andy van Houtte Product Engineer-LVL Nelson Pine Industries Nelson, NZ Andy Buchanan Professor of Civil Engineering Peter Moss Associate
More informationTimber to Timber - Timber to Concrete - Timber to Steel
01/2017 TIMBER CONNECTORS NOT TO BE USED IN EXTERIOR SITUATIONS Stainless Steel alternatives are available where stated Timber to Timber - Timber to Concrete - Timber to Steel MiTek manufactures and markets
More informationWithdrawal Strength of Staples
Holding Strength of Staples Staples are widely used in the furniture industry, both for upholstering purposes and for frame construction. The staples used for upholstering are usually rather small and
More informationJoshua Woodsman
CONSTRUCTION GUIDE of one of our design Please Note This electronic document is protected by the identifier against unauthorized dissemination on the Internet. Before building any structure make sure you
More informationWOOD WOOD
12655 - WOOD 12655-1 Part One - General WOOD 1.0 All materials used in the finishing shall be of the highest grade of their respective kinds. Materials shall be evenly and smoothly applied by skilled mechanics.
More informationSPUNKY ASSEMBLY MANUAL
SPUNKY ASSEMBLY MANUAL Please read the tips section at the back of this manual regarding the use of laser cut parts. The proper removal and preparation of these parts is important. When laser cut, some
More informationMachine threads are usually functional with internal-threaded workpieces, such as nuts
2010 Screws Machine Threads. i macine thread Machine threads are usually functional with internal-threaded workpieces, such as nuts Wood Metal Sheet Threads. i A type thread AB type thread 17 type thread
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationExpressed Hardwood Structures
Expressed Hardwood Structures Introduction This guide provides ideas and design information to assist in the development of expressed native timber structures in buildings. Basic information on how to
More informationB Connectors. Automation. Structural Framing System Connectors & Fasteners
BContents B Connectors Gussets... 2 End Fasteners... 4 Anchor Fasteners... 5 Angle Brackets... 6 45 Support Brackets... 8 Butt Fasteners... 9 Hinged Support Brackets... 10-13 Joining Plates... 14-18 Nuts
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationConnection Options for Wood-Frame and Heavy Timber Buildings Effective solutions provide strength, stiffness, stability and ductility
Photo: Robert Benson Photography Portland Jetport, Portland, Maine Architect: Gensler Southern pine glulam was chosen for this 40,000-sf roof because of its ability to span long distances with minimal
More informationGlulam Connection Details
T E C H N I C A L N O T E Glulam Connection Details Note: This version is superseded by a more current edition. Check the current edition for updated design and application recommendations. ENGINEERED
More informationAPA Performance Rated Rim Boards
D a t a F i l e APA Performance Rated Rim Boards A Rim Board is the wood component that fills the space between the sill plate and bottom plate of a wall or, in second floor construction, between the top
More informationConnection Philosophy. p NDS Chapter-by-chapter description Changes from previous editions Examples. Part 1: Member Design Webinar.
Outline ASD and LRFD with the 2005 NDS Part 2 Connection Design Presented by: John Buddy Showalter, P.E. Vice President, Technology Transfer Connection philosophy p NDS Chapter-by-chapter description Changes
More informationAttachment of Residential Deck Ledger to Metal Plate Connected Wood Truss Floor Systems Overview Revised 9/2/2016
Attachment of Residential Deck Ledger to Metal Plate Connected Wood Truss Floor Systems Overview Revised 9/2/2016 SBCA has been the voice of the structural building components industry since 1983, providing
More informationFASTENERS. Fasteners. Steel fasteners. Hexagon socket screws. Steel fasteners MC6S
Steel fasteners 21 FASTENERS Steel fasteners Hexagon socket s MC6S Hexagon socket head cap Din 912. (ISO 4762). * Fully threaded. 100 101 102 12.9 Uncoated 8.8 Uncoated 8.8 BZP Blanc Zink plated Dim mm
More informationSECTION ROUGH CARPENTRY
SECTION 06100 ROUGH CARPENTRY PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. The work includes furnishing all labor, materials and equipment required to complete the Rough Carpentry work as shown on the Drawings
More informationTHE ENGINEERED WOOD ASSOCIATION
D A T A F I L E APA Performance Rated Rim Boards A rim board is the wood component that fills the space between the sill plate and bottom plate of a wall or, in second floor construction, between the top
More informationIndex Pipe Hangers and Straps
Index Pipe Hangers and Straps Fig. 1 Standard Clevis Hanger MSS-SP-69, Type 1 WW-H-171E, Type 1 Page 14 Fig. 1CI Clevis Hanger for A.W.W.A. Page 16 Fig. 81 Clevis Hanger WW-H-171E, Type 12 Page 70 Fig.
More informationThe Q Frame PROJECT. a picture frame with secrets created exclusively for the Router Forum
The Q Frame PROJECT a picture frame with secrets created exclusively for the Router Forum 007 OR RELEASE FPLANS APPROVED The Q Frame: Project Overview LIST OF MATERIALS Frame Sides & Face 3/4 x 5 1/2 x
More informationSECTION ROUGH CARPENTRY
SECTION 06100 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work of this Section shall include all materials and installation necessary to provide Rough Carpentry as shown and detailed on the Drawings and
More informationADDENDUM (February 2014) 2012 NDS Changes John Buddy Showalter, P.E., Bradford K. Douglas, P.E., Philip Line, P.E., and Peter Mazikins, P.Eng.
ADDENDUM (February 2014) 2012 NDS Changes John Buddy Showalter, P.E., Bradford K. Douglas, P.E., Philip Line, P.E., and Peter Mazikins, P.Eng. 1) Add to section on Dowel-type Fasteners as follows: Section
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More information10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS
10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS 10x12 WOOD SKID FLOOR FLOOR SYSTEM FOR 10x12 TRICO AND FLORA SHEDS RAW MATERIALS LIST: 2 (9) FLOOR FRAMING AND SHEATHING: 1) BAND BOARD 2 x 6 x 12 PRESSURE
More informationALUMIDI. Concealed beam hanger with and without holes Aluminum alloy tridimensional perforated plate ALUMIDI - 01 CERTIFIED STEEL-ALUMINUM
ALUMIDI Concealed beam hanger with and without holes Aluminum alloy tridimensional perforated plate CERTIFIED Available with and without holes. The 2200 mm model is also certified FIELD OF USE Timber-to-Timber
More informationCLT Connections Design Seminar on CLT Design, including Connections, and Resistance to Lateral and Gravity Loads
CLT Connections Design Seminar on CLT Design, including Connections, and Resistance to Lateral and Gravity Loads Moncton, NB December 1, 2015 Overview Why connections in CLT are different from other EWP
More informationShaker Wall Clock Version 1
Shaker Wall Clock Version 1 The construction of both the original and this version is as simple as the spare design. I will offer several options -- in construction techniques, dimensional changes and
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
FASTENER AND HARDWARE GENERAL REQUIREMENTS 1. DESCRIPTION This section contains general requirements for common hardware installation. Covered are selection and installation of cotter pins, installation
More informationFasteners. Metal Fasteners, Joining, and Adhesives. Bolts. Metal Fasteners, Joining, and Adhesives
Metal Fasteners, Joining, and Adhesives Fasteners Metal assemblies are often held together with fasteners, hardware devices that mechanically join or affix two or more objects together. Assembling with
More informationAV Fastener (M) Sdn. Bhd Screw Eye Description 6.41 Square Hook(Shoulder Hook) Screw Description 6.38 One End Threaded Rod Screw Description
AV Fastener (M) Sdn. Bhd. 6.42 Screw Eye 6.42 Screw Eye 6.41 Square Hook(Shoulder Hook) Screw 6.41 Square Hook(Shoulder Hook) Screw 6.38 One End Threaded Rod Screw 6.38 One End Threaded Rod Screw 6.36
More informationCollins Engineers Palmetto Islands County Park Boardwalk Repairs 03/28/2014 SECTION ROUGH CARPENTRY
PART 1 GENERAL 1.1 RELATED SECTIONS SECTION 061000 ROUGH CARPENTRY A. Drawings and general provisions of the Construction Contract, including General Conditions and Division 1 Specification Sections, apply
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2761 Reissued 10/2017 This report is subject to renewal 10/2019. DIVISION: 06 00
More informationNational Design Specification for Wood Construction. Copyright Materials. Learning Objectives
National Design Specification for Wood Construction The Wood Products Council is a Registered Provider with. Credit(s) earned on completion of this program will be reported to AIA/CES for AIA members.
More informationMasterpiece Module Kits N T-trak Module Kit Assembly Instructions
Masterpiece Module Kits N T-trak Module Kit Assembly Instructions For tips, watch Instructional Video at http://www.youtube.com/watch?v=fklebffclau Tools Required flat, sturdy work surface Quality grade
More informationSECTION MASONRY ANCHORAGE AND REINFORCEMENT. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 04080 MASONRY ANCHORAGE AND REINFORCEMENT Display hidden notes to specifier. (Don't know how? Click Here) A. Post installed masonry anchors. B. Miscellaneous
More informationSturdi-Wall Design Manual for SW46, SW66, SW63, SW64, SW60, SW83, SW84, and SW80 Models
Sturdi-Wall Design Manual for SW46, SW66, SW63, SW64, SW60, SW83, SW84, and SW80 Models Project Number ME086-05 by Brent Leatherman, P.E. Timber Tech Engineering, Inc E-Mail: bl@timbertecheng.com January
More informationWorkbench. Process Guide
Workbench Process Guide Design, Lumber, Tools & Nails Made entirely from 2x and 4x construction lumber Hardware speeds up the consturction while also reduces the amount of planing we have to do by using
More informationSkills. Pupil Homework Name :- Lesmahagow High School Technical Department. Homework Name the tool shown opposite.
Homework 27 1. Name the tool shown opposite. (Page 38) (1) Lesmahagow High School Technical Department 2. Name the tool shown opposite. (Page 39) (1) Practical Woodworking 3. Name the tool shown opposite.
More informationFine Homebuilding. Cottage Shed Plans
Fine Homebuilding Cottage Shed Plans 1 Front Elevation Designed with a cottage look, this small shed has clapboard siding on the front, a double door, a ramp to allow access for motorized yard equipment,
More informationAttachment of Residential Deck Ledger to Side of Metal Plate Connected Wood Truss Floor Ladder. Installation Instructions Revised 9/2/2016
Attachment of Residential Deck Ledger to Side of Metal Plate Connected Wood Truss Floor Ladder Installation Instructions Revised 9/2/2016 SBCA has been the voice of the structural building components industry
More informationLateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later
Lateral Support Decks over 24 above grade require lateral support* *Exceptions to be discussed later Decking Types of Decking: -2x4s & 2x6s -five quarter span rated decking boards -Wood plastic composite
More informationFASTENERS C O M P AT I B L E W I T H F E R O T I E S Y S T E M S. Which FERO Tie Systems Require Fasteners?
FASTENERS C O M P AT I B L E W I T H F E R O T I E S Y S T E M S Which FERO Tie Systems Require Fasteners? Structural Actions: Fastener,, or Both? With the exception of FERO tie systems that are directly
More information1.03 QUALITY ASSURANCE A. Inspection Agencies: 1. SPIB: Southern Pine Inspection Bureau; for all structural framing of roof joists and headers.
DIVISION 6 - WOOD AND PLASTICS SECTION 06100 - ROUGH CARPENTRY PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: 1. Rough carpentry for: a. Wood framing and sheathing for the new Rest Area building additions.
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 12, 2017 the Denver 12' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted. Under the
More informationTHE GATE COACHAll Rights Reserved 28, Jia Sarai N.Delhi ,-9998
1 P a g e 1 DESIGN AGAINST STATIC AND FLUCTUATING LOADS 2 SHAFT, KEYS AND COUPLINGS CONTENTS Introduction 6 Factor of safety 6 Stress concentration 7 Stress concentration factors 8 Reduction of stress
More informationDesign and Technology Resistant materials Key words and definitions
Design and Technology Resistant materials Key words and definitions Word Acrylic Definition a type of thermoplastic, which is hard and can be transparent. Used to make shop signs. Perspex is a trade/brand
More informationPiXL Independence. Technology Answer Booklet KS4. Wood. Contents: I. Multiple Choice Questions 10 credits in total
PiXL Independence Technology Answer Booklet KS4 Wood Contents: I. Multiple Choice Questions 10 credits in total II. III. Shorter Answer Questions 10 credits each Exam Style Questions 100 credits each 1
More informationWorking with Wood and Wood Materials
Working with Wood and Wood Materials Excerpt from the Bosch Encyclopedia of Power Tools. Written & Published by ROBERT BOSCH GmbH and Robert Bosch Tool Corporation. The grain direction of the fibers determines
More informationUL 580 Construction No: ½ in Snap Lock w/ Clip
Test Type: Testing Authority: Test Name: UL 580 Construction No: 589 Underwriters Laboratories Wind Uplift Test Date: Test Completed By: Testing Laboratory Type: Width: Clip Spacing: Decking Construction:
More informationFastener Basics. Common Fastener Types. Fastener Materials. Grade / Class and Fastener Strength
Fastener Basics Common Fastener Types Fastener Grade (US) or Class (metric) refers to the mechanical properties of the fastener material. Generally, a higher number indicates a stronger, more hardened
More informationBest Barns USA. Assembly Book. 12'x 16' the Millcreek. Revised September 19, 2017
Assembly Book Best Barns USA Revised September 19, 2017 the Millcreek 12'x 16' Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted Under the
More informationCity of Manteca Boarding Requirements
City of Manteca Boarding Requirements There should be no boarding above the first floor unless entry is possible without use of a ladder, and the opening is large enough for a person to easily pass through.
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 19, 2017 the Millcreek 12'x 20' Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted Under the
More informationHow to Build Good Decks..
How to Build Good Decks.. Worldwide Sleeping Company, Inc Cary, North Carolina Decking Overview.. Decking Overview.. more Decking Joist.... Joist Hanger Ledger Lag Screw House Wall Decking House Floor
More informationK/D FITTINGS & FASTENERS
K/ FITTINGS & FASTENERS -1 Screws P. 162-168 -2 Connector Bolts P. 169-173 -3 K/ Fittings P. 174-177 -4 Insert Nuts P. 178-181 -5 Allen Keys P. 182-183 -6 Nails & Wall Plugs P. 184 -1 Screws 1010 Machine
More informationSECTION CARPENTRY
SECTION 06100 CARPENTRY PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Carpentry work including grounds, nailers, blocking, miscellaneous framing, plywood backing panels, plywood sheathing, preservative
More informationGlued laminated timber beams repair.
Glued laminated timber beams repair. Master s Degree Extended Abstract Ricardo Cardoso Henriques da Silva Keywords: glulam, delamination, self-tapping screw, plywood, repair November 2014 1. INTRODUCTION
More informationmila-wall (Series100) General Operating Instructions page 1 of 15
mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded
More informationCONCEALED HOOK CONNECTORS UV-T / UV-C
CONCEALED OOK CONNECTORS / UV-C GEOMETRY Choice of connection system according to the secondary joist cross section SECONDARY JOIST [] SECONDARY JOIST DEPT [] 300 250 200 150 100 50 0 0 200 400 600 800
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised February 4, 2016 the Millcreek-R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationRatcheting and Angled Leg Vises. Ratcheting Parallel Guide
Ratcheting and Angled Leg Vises Ratcheting Parallel Guide In Scott Landis s The Work Bench Book there is a drawing of a ratchet mechanism for a parallel guide. It was one of those little tidbits I tend
More information1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"
More informationA. Boards or Strips: Lumber of less than 2 inches nominal size in least dimension.
HIGGINSVILLE HABILITATION CENTER MISC. BUILDING RENOVATIONS STATE OF MISSOURI HIGGINSVILLE, MISSOURI SECTION 061000 - ROUGH CARPENTRY PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More informationInstallation of Balustrade Systems
Installation of Balustrade Systems IMPORTANT: Be sure to mark the center point of each newel post's location prior to installation to insure proper spacing. All product interfaces must use PL Premium Adhesive
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationCopyright WilkerDos.com Dining Table. Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.
Copyright WilkerDos.com 2017 Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.com) Layout & Shopping List Page 2 of 12 Layout & Shopping List Item Quantity Description
More informationWood Products Taxonomy
THEN NOW Wood Products Taxonomy WOOD Composites Solid Wood Panels Engineered Lumber Composites (ELC) Softwood Lumber Glued Treated Hardwood Lumber Wood/ Non-wood Wood Based LVL Boards Finger joined CCA
More informationHOMESTEADER DELUXE PACKAGE
HOMESTEADER DELUXE PACKAGE ASSEMBLY INSTRUCTIONS #011-00003 SWEEP TUB ASSEMBLY STEP 1: Place the hinge side of the Sweep Bow Gate where the center of the sweep will be located. Then take the four Bottom
More informationSWAY BRACE PIPE ATTACHMENT FIG. 010
Function: Designed for bracing pipe against sway and seismic disturbance. The pipe attachment component of a sway brace system used in conjunction with a PHD Manufacturing structural attachment fitting,
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised December 6, 2013 the Denver-R 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationDesign Nailed and Wood Screwed Connections with Spreadsheet. Course Content
Design Nailed and Wood Screwed Connections with Spreadsheet Course Content INTRODUCTION The complete design of a wood structure includes the design of connections between the various structural members.
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationAdjustable Box Joint Jig. Richard Hicks on 8/24/2015. Box or Finger Joints
Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box or Finger Joints Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box Joints are also called Finger Joints Because they have interlocking fingers
More informationFORMWALL Ceiling Plank / Board Installation Guide
FORMWALL Ceiling Plank / Board Installation Guide Nuplex Ceiling Plank Installation Guide This fitting guide is for guidance only. Refer to the installing contractor and/or builder for the exact job process.
More information(1) Method to fix Mechanically with BOLT or NUT
(1) Method to fix Mechanically with BOLT or NUT Fig. 1 Nut with Grooving Set Screw Fig. 2 Set Screw Method 1. Fixing by putting split pin. 2. Certain prevention for coming out is possible. 3. In order
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 3
Kentucky 4H Wood Science Plans Notebook Plans Level 3 MATERIALS: 2 pieces wood 3/4 x 10 x 4 1 piece wood 3/4 x 12 x 4 2 pieces wood 3/4 x 3 x 2 5 1/2" 2 pieces wood 3/4 x 3 x 1 8 1 piece wood 2 x 4 x
More information