Stainless Steel Rotary Indexing Tables and A-Axes for Wire and Sinking EDM. Catalogue RE 4905

Transcription

1 Stainless Steel Rotary Indexing Tables and A-Axes for Wire and Sinking EDM Catalogue RE 4905

2 Rotary Indexing Tables and A-Axes by HIRSCHMANN Pin point accuracy Controlled dynamic power Consistent performance. mm Positioning accuracy to ±2 sec. mm Repetitive accuracy to ±1 sec. A-Axis H80R.NCF.6 A-Axis H150R.NCF with tool holder SK50 Rotary Indexing Table H160R.NCF Rotary Indexing Table H400NCS mounted on Sine Table 2

3 Rotary Indexing Tables and A-Axes Contents Operation All Rotary Indexing Tables and A-Axes are supplied with operating and mounting manuals. Interface information is also included. Observe operation instructions of machine manufacturer, especially when Rotary Indexing Tables and A-Axes are connected with machine control systems and are controlled by them. Correct operation cannot be ensured and danger to personnel and machine cannot be excluded unless these operating instructions or information given in this catalogue are observed. Service and Maintenance Since Rotary Indexing Tables and A-Axes are subject to chemical and physical influences, maintenance and service has to be performed with special care. EDM current flow requires a good conductive connection (contact) to machine table. The conductivity of water and chlorides normally contained in water can influence the rust-resistant properties of the axis. Residues (varnishes, eroded particles etc.) from the electrical discharge process should be removed on a daily basis. Contact your local HIRSCHMANN dealer for recommended products to use. mm Rotary Indexing Tables and A-Axes In Use 2 mm Maintenance, Cleaning, Quality 3 mm Introduction, Characteristics 4 mm Accuracy, Control System 5 mm Rotary Indexing Table Models 6 mm A-Axes with AC Drive Models 8 mm A-Axes with Machine Tapers (BT, SK, HSK, CAT) 9 mm Rotating Spindles 10 mm High Speed Rotating Spindle Applications 11 Technical Modifications All products shown in this catalogue are subject to ongoing improvements and developments; we reserve the right for technical modifications without notice. Quality according to DIN EN ISO 9001:2000 All HIRSCHMANN products are produced using state of the art production methods. They are subject to quality assurance measures as per DIN EN ISO 9001:2000 both during production and in the assembly stage. All tables and axes are fully tested for all functions in a submerged environment. Warranty We provide a 12 month warranty for all Rotary Indexing Tables and A-Axes, starting from the invoice date, and assuming correct use and maintenance as specified. The warranty is restricted to replacement or repair, free of charge, of any defective parts. Claims arising from improper use or handling shall not be considered. Warranty claims must be submitted in writing and without delay. HIRSCHMANN GmbH 3

4 Rotary Indexing Tables and A-Axes for Wire and Sinking EDM Introduction Many erosion tasks cannot be solved efficiently without using a Rotary Indexing Table or an A-Axis, as for example wire cutting of carbide tipped tools and turbine rings. Over 150 HIRSCHMANN axes are used in the orthopaedic industry worldwide for the manufacture of saw guides and replacement body parts. HIRSCHMANN Rotary Indexing Tables and A-Axes are manufactured with faceplates with a diameter range from 80 to 800 mm and/or machine tapers mountings SK50 or HSK63. Innovative HIRSCHMANN Rotary Indexing Tables and A-Axes increase productivity of EDM and improve the quality of their products. Characteristics Direct measuring system (closed loop) Speed range up to 30 rpm Faceplate diameters from 80 to 800 mm Machine tapers BT, SK, CAT and HSK For horizontal, vertical and tilt via sine use All surfaces and functional parts are stainless steel Less maintenance required Completely sealed (IP68) for use on Wire or Sinking EDM No air purge required 4

5 General Accuracy HIRSCHMANN Rotary Indexing Tables and A-Axes are manufactured to high precision standards and are subject to rigid quality controls. Indexing and positioning accuracy are proportionally dependant on the quality of the measuring system and a drive system that is free from backlash. HIRSCHMANN Rotary Indexing Tables and A-Axes are always provided with a direct measuring system and an OTT worm pinion free of backlash or Harmonic Drive gears. These are conditions for highest accuracy and high precision positioning. Positioning accuracy is measured every 15 degrees (forward and back). The results are furnished in a test certificate which is part of the documentation enclosed with each Rotary Indexing Table and A-Axis. Control System HIRSCHMANN Rotary Indexing Tables and A-Axes can be integrated to machine control as an additional axis by the OEM allowing the possibility to Turn & Burn. For easy and quick integration the Tables and A-Axes can be provided with AC or DC drives and measuring systems of the various manufacturers that are compatible to their control systems. When integration to the machine control is not possible, the HIRSCHMANN Control System H1625 can be used. It can be connected to the machine control via a 24v signal for automatic indexing only. In this case Turn & Burn is not possible. Rotary Indexing Tables and A-Axes are compatible to EDM following manufacturers: AGIE, BES, CHARMILLES, ELECTRONICA, EXERON, FANUC, MAKINO, MITSUBISHI, OPS-INGERSOLL, SODICK and others. HIRSCHMANN manufactures Rotary Indexing Tables with face plates from 80 to 800 mm 5

6 Rotary Indexing Tables All HIRSCHMANN Rotary Indexing Tables are equipped with a direct measuring system (Closed loop). If necessary, an internal electromagnetic or pneumatic brake for the clamping of face plate (Rotary Table) is installed. As standard a DC drive is integrated but can be changed to an AC drive for machine control integration. Common characteristics Direct measuring system Low-backlash free drive For horizontal and vertical use DC drive, (available also with AC drive) Stainless steel IP68 H80R.NC Rotary Indexing Axis With manual clamper H8.16R for mounting of pallets and holders of HIRSCHMANN Fixturing System Horizontal use only. Dimensions (BxTxH) approx. 230/252/130 mm (21.62 x9.93 x5.12 ) Min. indexing step 0,001 /3,6 Indexing accuracy ±10 Repetitive accuracy ±5 Max. weight 25 kg ( lbs) (part, pallet and fixture) Direct measuring system RON 255, 275 or 287 Drive DC motor Holding force of plate (electromagnetic) 20 Nm Speed max. 5 min -1 approx. 35 kg ( lbs) H 100R.NC Rotary Indexing Table Face plate (mounting surface) Ø 100 mm, for horizontal and vertical use. Dimensions (BxTxH) approx. 188/125/135 mm (7.41 x4.93 x5.32 ) Min. indexing step 0,001 /3,6 Indexing accuracy ±20 Repetitive accuracy ±10 Max. weight (part and fixture) 50 kg ( lbs) Direct measuring system ERN 480 Drive DC motor Brake holding force (pneumatic) 25 Nm Speed max. 5 min -1 approx. 19 kg ( lbs) H 160R.NC Rotary Indexing Table Face plate (mounting surface) Ø 160 mm, for horizontal and vertical use. Dimensions (BxTxH) approx. 265/203/148 mm (10.44 x7.99 x5.83 ) Min. indexing step 0,001 /3,6 Indexing accuracy ±5 Repetitive accuracy ±2,5 Max. weight (part and fixture) 100 kg (220.5 lbs) Direct measuring system RON 255, 275 or 287 Drive DC motor Brake holding force (electromagnetic) 20 Nm Speed max. 5 min -1 approx. 40 kg (88.2 lbs) 6

7 H250R.NC Rotary Indexing Table Face plate (mounting surface) Ø 250 mm, for horizontal and vertical use. Dimensions (BxTxH) approx. 340/290/135 mm (13.39 x11.42 x5.31 ) Min. indexing step 0,001 /3,6 Dividing accuracy ±5 Repetitive accuracy ±2,5 Max. weight (part and fixture) 250 kg ( lbs) Direct measuring system RON 255, 275 or 287 Drive DC motor Brake holding force (electromagnetic) 20 Nm Speed max. 5 min -1 approx. 45 kg ( lbs) H400R.NC Rotary Indexing Table Similar to H250, face plate (mounting surface) Ø 400 mm, Dimensions (BxTxH) approx. 490/410/175 mm (19.30 x16.15 x6.89 ) Max. weight (part and fixture) 450 kg ( lbs) approx. 200 kg (441 lbs) H800R.NC Rotary Indexing Table Similar to H250, face plate (mounting surface) Ø 800 mm, Dimensions (BxTxH) approx. 820/800/250 mm (32.30 x31.52 x9.85 ) Max. weight (part and fixture) 2000 kg (4410 lbs) approx. 620 kg ( lbs) H1625 CNC Control Programmable positioning control for H80, H160, H250 and H400. Dimensions (BxTxH) approx. 450/450/130 mm (17.73 x17.73 x5.12 ) Power supply 115/230 V 50/60 Hz approx. 10 kg (22.05 lbs) H CNC Control Similar to H1625, for Rotary Indexing Table H400R.NC. H CNC Control Similar to H1625, for Rotary Indexing Table H100R.NC. H CNC Control Similar to H1625, for Rotary Indexing Table H800R.NC. 7

8 A-Axes with AC Drive General A-Axes can be used together with drives and measuring systems of different manufacturers and types allowing integration to the machine control systems. Technical characteristics such as indexing accuracies, minimum indexing steps and the ability to Turn & Burn depend on machine control system used. Common characteristics For use on Wire and Sinking EDM (all surfaces and functional parts are made of stainless steel) AC drive, direct measuring system Minimum indexing step (depending on Rotary Encoder and Control System) up to 0,0001 /0,36 Indexing accuracy (depending on Rotary Encoder and Control System) up to ±3 Repetitive accuracy (depending on Rotary Encoder and Control System) up to ±2 H 80R.NCx A-Axis With manual clamper H8.16R for mounting holders and pallets of Fixturing System 5000/ 6000, horizontal use. Dimensions (BxTxH) approx. 230/220/130 mm (9.06 x8.66 x5.12 ) Min. indexing step 0,0001 /0,36 Max. weight (part and fixture) 25 kg ( lbs) Brake holding force (electromagnetic) 20 Nm approx. 35 kg ( lbs) Speed max. 20 min -1 Erosion current max. 30 A H 80RNCx.6 A-Axis Similar to H80R.NCx but with pneumatic clamper for mounting of pallets and holders of HIRSCHMANN Fixturing System 5000/ H 100R.NCx A-Axis With insulated face plate (rotary table) Ø 100 mm, horizontal and vertical use. Dimensions (BxTxH) approx. 230/220/130 mm (9.06 x8.66 x5.12 ) Max. weight (part and fixture) 25 kg ( lbs) approx. 30 kg (66.15 lbs) Speed max. 20 min -1 Erosion current max. 50 A H 160R.NCx A-Axis With face plate (rotary table) Ø 160 mm, horizontal and vertical use. Dimensions (BxTxH) approx. 272/235/180 mm (10.71 x9.25 x7.09 ) Min. indexing step 0,0001 /0,36 Max. weight (part and fixture) 100 kg (22.05 lbs) approx. 45 kg ( lbs) Speed max. 8 min -1 Erosion current max. 50 A x = motor type (F = FANUC, M = MITSUBISHI, P = PANASONIC etc.) 8

9 A-Axes with Machine Taper Mounting Common characteristics of A-Axes H150R.NC For use on Wire and Sinking EDM (all surfaces and functional units are made of stainless steel) Dimensions (BxTxH) 265/215/160 mm (10.44 x8.47 x6.30 ) Minimum indexing step (depending on Rotary Encoder and Control System) up to 0,0001 /0,36 Indexing accuracy (depending on Rotary Encoder and Control System) up to ±5 Repetitive accuracy (depending on Rotary Encoder and Control System) up to ±2,5 Max. weight (part and fixture) up to 50 kg ( lbs) Direct measuring system (depending on Control System) FANUC, HEIDENHAIN, RENISHAW etc. Drive (depending on Control System) FANUC, HEIDENHAIN, RENISHAW etc. Speed (depending on Control System) up to 20 min -1 approx. 45 kg ( lbs) Max. erosion current 50 A H 150R.NCxZ2 A-Axis With machine taper mounting SK50, manual tool clamping. H 150R.NCxZ2A A-Axis With machine taper mounting SK50, pneumatic tool clamping. H 150R.NCxZ8 A-Axis With machine taper mounting HSK63 Form F, manual tool clamping. H 150R.NCxZ8A A-Axis With machine taper mounting HSK63 Form F, pneumatic tool clamping. H 150R.NCxZ9 A-Axis With machine taper mounting HSK63 Form A, manual tool clamping. H 150R.NCxZ9A A-Axis With machine taper mounting HSK63 Form A, pneumatic tool clamping. x =motor type (F = FANUC, M = MITSUBISHI, P = PANASONIC etc.) H150R.NCx with face plate Ø 150 mm H150R.NCx with 3-jaw chuck 9

10 Rotating Spindles Rotating Spindle H80R.M For spark erosion turning of work pieces on Wire or Sinking EDM H 80R.M Rotating Spindle Stainless steel, with maintenance-free DC drive Dimensions (BxTxH) 180/195/98 mm (7.09 x7.68 x3.86 ) Speed min -1 Axial accuracy <=0,005 mm ( ) Work piece mounting (clamper) H8.16R approx. 20 kg (44.10 lbs) H 20.2 Control Unit Required for controlling the speed of Rotating Spindle H 80 R.M Dimensions (BxTxH) 270/330/320 mm (10.64 x13 x12.61 ) Power supply 230 V/50/60 Hz Input max. 100 VA H80R.MAC High Speed Rotating Spindle The advancement in regions of micro-mechanic requires new ideas in production strategy. Dynamically balanced parts with minimal diameters, difficult or impossible to manufacture on conventional lathes and grinding machines, can now be manufactured on a standard Wire EDM equipped with this proven high speed spindle. High surface quality and accuracy by erosion turning or grinding is achieved on small to larger dynamically balanced work pieces. Characteristics: Alternative to hard turning or precision grinding of dynamically balanced parts Spark erosion turning with highest surface quality Economic production of parts with minimal structures, stainless steel microelectrodes, hard alloys, nonferrous metals and conductive ceramics H 80R.MAC Rotating Spindle Stainless steel, with maintenance-free AC drive Dimensions (BxTxH) 180/195/98 mm (7.09 x7.68 x3.86 ) Speed min -1 Axial accuracy <=0,005 mm ( ) Workpiece mounting (clamper) H8.16R approx. 20 kg (44.10 lbs) H 1680.AC4 Speed Control Unit Required for controlling the speed of Rotating Spindle H80R.MAC Dimensions (BxTxH) 270/330/320 mm (10.64 x13 x12.61 ) Power supply 230 V/50/60 Hz Input max. 500 VA 10

11 Rotating Spindle H80R.MAC Applications in Micro-technics Micro ejecting pin, l = 10 mm (0.394 ) Ra 0,2 0,25 µm, tolerance zone f6 Parts eroded on Wire EDM using Rotating Spindle H80R.MAC Micro pin structure in hard alloy, l = 10 mm (0.394 ) Special steel piston for micro pump, accuracy of ball profile 1 2 µm H80R.MAC in use on Wire EDM Special steel needle for medical technics Ra 0,2 0,25 µm Electrode eroded on Wire EDM Part machined on Sinking EDM puncture depth 0,25 mm (0,00985 ) 11

12 Stainless Steel Rotary Indexing Tables and A-Axes for Wire and Sinking EDM PRODUCT OVERVIEW Fixturing System 4000 For Wire EDM Fixturing System 5000 For Sinking EDM Fixturing System 8000 For Machine Tools Fixturing Spannsystem System 9000 Modular Zero Point Fixturing System Representatives, consultants and distributors in: Australia Austria Belgium Brazil Canada China Denmark Finland France Great Britain Hong Kong Indonesia Israel Italy Japan Malaysia Netherlands Norway Portugal Singapore Spain Sweden Taiwan Thailand USA High-duty Rod-end and Spherical Bearings Please ask for our catalogues. HIRSCHMANN GMBH KIRCHENTANNENSTRASSE 9 D FLUORN-WINZELN FON +49 (0) FAX +49 (0) info@hirschmanngmbh.com