(a) Machine Construction General (a) 4/5/2016
|
|
|
- Patricia Fields
- 6 years ago
- Views:
Transcription
1 WOODWORKING MACHINERY REQUIREMENTS (a) Machine Construction General Machines shall be constructed to be free from vibration when largest tool is mounted and run at full speed (a) All belts, pulleys, gears, shafts, and moving parts shall be guarded in accordance with the specific requirements of
2 (a) It is recommended that each power-driven woodworking machine be provided with a disconnect switch that can be locked in the off position (a) All tools operating at more than 90v must have their metal parts grounded Separate ground wire and polarized plug Cutting heads must be machined to fit specific types of arbors (a) Combs (featherboards) shall be provided at the workplace for use when a standard guard cannot be used. 2
3 Woodworking Machines Woodworking Machines (b) Machine Controls and Equipment A mechanical or electrical power control shall be provided on each machine to make it possible for the operator to cut off the power from each machine without leaving his position at the point of operation. 3
4 (b)(3) On applications where injury to the operator might result if motors were to restart after power failures, provision shall be made to prevent machines from automatically restarting upon restoration of power (b) Operating controls must be placed so the operator has access to them without reaching over the cutting blade Must be placed within reach of their regular work station Machines operated by electrical motors must have controls capable of being rendered inoperative For maintenance, repairs, adjustments, etc (b) Operating treadles must be protected from unintended operation. Feeder attachments must have feed rolls or other moving parts covered to protect operator from pinch points 4
5 Foot Pedal (c) Hand-Fed Ripsaws Each circular hand-fed ripsaw shall be guarded by a hood which shall completely enclose that portion of the saw above the table and that portion of the saw above the material being cut. The hood and mounting shall be arranged so that the hood will automatically adjust itself to the thickness of and remain in contact with the material being cut without considerable resistance. Table Saw 5
6 Table Saw (c) Each hand-fed circular ripsaw shall be furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator (c) Each hand-fed circular ripsaw shall be provided with non-kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or throw it back toward the operator. 6
7 Dogs Anti-Kickback Fingers (d) Hand-Fed Crosscut Table Saws Each circular crosscut table saw shall be guarded by a hood which shall meet all the requirements of (c)(1) for hoods for circular re-saws. 7
8 (f) - Self-Feed Circular Saws Self-feed circular saws Guarded by a hood or guard to prevent hands of operators from coming in contact with the in-running rolls. If self-fed saws are used for ripping they must be equipped with anti-kickback devices (dogs) (g) Swing Cut Off Saws Swing Cut Off Saws Provided with a hood that completely covers the upper half of the blade and the arbor. Provided with a guard that will protect the point of operation. Must be provided with a means to return to it s resting position Limit chain to limit the travel beyond or behind the working table Swinging Cut Off Saw 8
9 (h) Radial Saws The upper hood shall completely enclose the upper portion of the blade down to a point that will include the end of the saw arbor.the sides of the lower exposed portion of the blade shall be guarded to the full diameter of the blade by a device that will automatically adjust itself of the thickness of the stock and remain in contact with the stock (h) Radial Saws (h) Each radial saw used for ripping shall be provided with non kickback fingers or dogs located on both sides of the saw. 9
10 (h) An adjustable stop shall be provided to prevent the forward travel of the blade beyond the position necessary to complete the cut in repetitive operations (h) Installation shall be in such a manner that the front end of the unit will be slightly higher than the rear, so as to cause the cutting head to return gently to the starting position when released by the operator. Woodworking Machines 10
11 Woodworking Machinery Woodworking Machines (h) Radial Saws 11
12 (h) Radial Saws Ripping and ploughing shall be against the direction in which the saw turns. The direction of the saw rotation shall be conspicuously marked on the hood (i) Bandsaws and Band Resaws All portions of the saw blade (bandsaws) shall be enclosed or guarded, except for the working portion of the blade between the bottom of the guide rolls and the table (i) - Bandsaws 12
13 Woodworking Machinery (j) - Jointers Jointers Cylinder cutting head that doesn t extend more than 1/8 from the head. Each hand-fed jointer with a horizontal cutting head shall have an automatic guard which will cover all the section of the head on the working side of the fence or gage. 13
14 Woodworking Machinery (j) (m) Wood Shapers and Similar Equipment The cutting heads of each wood shaper, handfed panel raiser, or other similar machine not automatically fed, shall be enclosed with a cage or adjustable guard so designed as to keep the operator s hand away from the cutting edge. 14
15 Wood Shaper Shaper With Adjustable Guard (m) Double-spindle shapers Starting and stopping device for each spindle 15
16 (n) Planing Planers Guard covering the cutting heads If exhaust hood used, must be integral to the guard Guard/hood must protect the feed rolls/inrunning nip points Woodworking Machinery Woodworking Machinery 16
17 (o) Wood-Turning Lathes Cutting heads on wood-turning lathes, whether rotating or not, shall be covered as completely as possible by hoods or shields (o) Wood stock held between two centers on a lathe must be protected (as much as possible) with a long curved guard extending over the top of the lathe to prevent the work from being thrown out. If an exhaust system is used it must form an integral part of the guard. Woodworking Machinery 17
18 (p) Sanding Machines Sanding Machines Where the sanding belt runs over rollers a guard must prevent the operator from coming into contact with the in-running nip points. Drum sanders must be protected above the table by a guard or exhaust hood except for that portion of the sander which is necessary for the stock (p) Disk sanders must have a guard or exhaust hood enclosing the revolving disk. Allowing only enough exposure which is necessary for the application (p) Belt sanding machines shall be provided with guards at each nip point where the sanding belt runs on to the pulley...the unused run of the sanding belt shall be guarded against accidental contact. 18
19 Woodworking Machinery (r) Miscellaneous Woodworking Machines The mention of specific machines in paragraphs (a) thru (q) and this paragraph (r) of this section, inclusive, is not intended to exclude other woodworking machines from the requirements that suitable guards and exhaust hoods be provided to reduce to a minimum the hazard due to the point of operation of such machines (s) Inspection Maintenance of Woodworking Machinery All knives and cutting heads of woodworking machines shall be kept sharp, properly adjusted, and firmly secured. Where two or more knives are used, they shall be properly balanced. 19
20 (s) Arbors of all circular saws shall be free from play Sharpening or tension of saw blades or cutters shall be done by persons of demonstrated skill Emphasis shall be placed on the importance of cleanliness of the woodworking area (s) All cracked saws shall be removed from service. The practice of inserting wedges between the saw disk and the collar to form a wobble saw shall be prohibited (s) Push sticks and push blocks shall be provided for small pieces of wood and for pushing the stock past the blade. 20
21 Woodworking Machinery 21
WOODWORKING MACHINERY GUARDING
APPENDIX E WOODWORKING MACHINERY GUARDING The following requirements are restated from 29 CFR 1910.213, Woodworking machinery requirements. (a) Machine construction general. (1) Each machine shall be so
Subpart O - Machine Guarding. OTI 501 Paul A. Schlumper, PE, CSP
Subpart O - Machine Guarding OTI 501 Paul A. Schlumper, PE, CSP 1 We Will Cover: Machine Guarding Principles Subpart O - Highlights Mock Plant Walk-Through 2 Why are machines not guarded? No one would
Saw Safety Checklist
Saw Safety Checklist Saws Saws: Hand-Fed Ripsaws [ ] [ ] [ ] 1. Is the circular hand-fed ripsaw guarded by a hood that completely encloses the portions of the saw that are above the table and above the
Table of Contents Responsibilities... 3 Department Head & Supervisors... 3 Employees & Student Laborers... 3 Machine Guarding Definitions 29 CFR
Machine Guarding Table of Contents Responsibilities... 3 Department Head & Supervisors... 3 Employees & Student Laborers... 3 Machine Guarding Definitions 29 CFR 1910.211... 4 General requirements for
Woodworking Machinery- Other than Saws Self-Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Woodworking Machinery- Other than Saws Self-Inspection Checklist Guidelines: This checklist
Tech Ed Lab Safety SAFETY RULES Page 1-1
SAFETY RULES Safety Rules for Working with Wood 1. Secure your instructor s approval for all work you do in the shop. 2. Wear safety glasses when doing any operation that may endanger your eyes. 3. Always
Environmental Health and Safety Department
Machine Guard Handout Bench Grinder Adjust tongue to ¼ inch from blade Adjust work rest to 1/8 inch from the blade Because the safety guard is designed to restrain the pieces of a shattered grinding wheel,
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS DIRECTOR'S OFFICE GENERAL INDUSTRY SAFETY AND HEALTH STANDARD
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS DIRECTOR'S OFFICE GENERAL INDUSTRY SAFETY AND HEALTH STANDARD (By authority conferred on the director of the department of licensing and regulatory affairs
Effective Date: 15-March Table of Contents
Version: 4 Page: 1 of 12 Table of Contents 1.0 Introduction... 2 1.1 Purpose... 2 1.2 Scope... 2 1.3 Definitions... 2 1.4 Responsibilities... 3 Environmental Health and Safety Office (EHSO) and applicable
College of Forestry 610: Power Tools
College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide
HAND AND POWER TOOLS
HAND AND POWER TOOLS Steingass Mechanical Contracting, Inc. 754 Progress Drive Medina, Ohio 44256 (330) 725-6090 HAND AND POWER TOOLS General All power tools whether furnished by Steingass Mechanical Contracting,
CITY AND COUNTY OF DENVER CR&CF RISK UNIT Machine Guarding Safety Standard
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.5.8 Machine Guarding Safety Standard 1.0 Introduction 2.0 Scope Lacerations to hands, fractured fingers, amputated fingers and hands are just a few of the more
NC Employees Workplace Program Requirements for Safety and Health. Machine Guarding
Scope Machine Guarding A wide variety of mechanical motions and actions on machines may present hazards to employees. These can include movement of rotating members, reciprocating arms, moving belts, meshing
SAFETY INFORMATION PACKET
WILLOWCREEK MIDDLE SCHOOL SAFETY INFORMATION PACKET GENERAL SHOP SAFETY 1 WIDE BELT SANDER 2 BAND SAW 3 MITER SAW 4 UP- CUT SAW 4 PLANER 6 TABLE SAW 7 DRILL PRESS 8 LATHE 8 DISK / VERTICAL BELT SANDER
Guild of Oregon Woodworkers Shop Safety Test
Guild of Oregon Woodworkers Shop Safety Test You must pass the Test with an 80% or better and self-correct it to 100% Make sure you put the answers under the correct portion of the answer sheet for the
Yale Practices for Tool Safeguarding and Controls 1
Arbor Press Manual Caught between crushing, limited by manual operation Band Saw / Small Bench Cutting blade lacerations Rotating blade pulleys pinch points, entanglement for wood Band Saw / Large Cutting
POTENTIAL HEALTH & SAFETY HAZARDS
Number: OH&S 18.32.1 Revision Date: 03/12/2014 Radial Arm Saw Safety 1. PURPOSE 1.1. To provide operational guidelines on the safe use of Radial Arm Saws found in woodworking shops at Thompson Rivers University
Surface planer or buzzer. Performs the tasks of dressing, squaring and straightening timber Machining short lengths of timber. Without the bridge guard. Without the appropriate training. Without PPE. Set
Subpart O - Machine Guarding
Subpart O - Machine Guarding We Will Cover: Machine Guarding Principles Subpart O - Highlights Mock Plant Walk-Through Why are machines not guarded? No one would stick their arm, hand, finger, head, etc.
Agricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
Western Illinois University Department of Art Woodshop Orientation
Western Illinois University Department of Art Woodshop Orientation SAFETY is the first priority woodworking tools are inherently dangerous. Machines turn sharp saw blades and cutters at high speeds. Accidents
Occupational Safety, Health and Welfare (Woodworking Machines) Regulations 1989
Occupational Safety, Health and Welfare (Woodworking Machines) Regulations 1989 GN 66/1989 THE OCCUPATIONAL SAFETY, HEALTH AND WELFARE ACT 1988 Regulations made by the Minister under section 80(1) of the
Revised 8/1/2018 Page 1
1Guild of Oregon Woodworkers Shop Safety Test You must pass the Test with an 80% or better and self-correct it to 100%. Make sure you put the answers under the correct portion of the answer sheet for the
WESTERN ILLINOIS UNIVERSITY DEPARTMENT OF ART
WESTERN ILLINOIS UNIVERSITY DEPARTMENT OF ART WOODSHOP ORIENTATION SAFETY is the first priority woodworking tools are inherently dangerous. Machines turn sharp saw blades and cutters at high speeds. Accidents
WORKSHOP SAFETY POLICIES
WORKSHOP SAFETY POLICIES 1 TABLE OF CONTENTS Scope 3 Responsibilities 3 General Safety Guidelines 4 Machine Safety 6 Drill Press 6 Boring Mill 6 Grinder 7 Lathe 8 Milling Machine 9 Band Saw 10 Horizontal
Hornsby Woodworking Men s Shed. Guide to the Shed s Woodworking Machines
Guide to the Shed s Woodworking Machines SP00 Purpose The primary purpose of this document is to assist the induction of new members of the Hornsby Woodworking Men s Shed in the identification and understanding
Portable Hand and Power Tools Self-Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Portable Hand and Power Tools Self-Inspection Checklist Guidelines: This checklist covers
WOOD SHOP SAFETY. Rev. 2011
INTRODUCTION WOOD SHOP SAFETY Hand tools and power driven machine tools have been developed to save time and to do more accurate work. A hand tool or power tool is built to perform a specific operation.
San Diego Fine Woodworkers Association Member Shop Safety Test
You must pass the Test with an 80% or better and self-correct it to 100%. Make sure you put the answers under the correct portion of the answer sheet for the test you are taking. Use the Guild Safety Answer
Machine Guarding/Shop Safety Risk Services Environmental Health & Safety 1370 Adams Avenue Costa Mesa, CA (714)
CONTENTS Authority Citations Purpose Hazardous Activities Equipment Operations Machine Guarding General Shop Rules Division of Responsibilities Program Notes Appendix A Appendix B Appendix C Appendix D
Copyright 2014 Curtis B. Vevang Page Number 1
As described on the Woodcraft Website: This is a 9 hour class consisting of 3, 3 hour sessions. The purpose of this class is to introduce woodworking from the ground up. The student will build a tool/garden
Chapter 8 Workshops and Maintenance
Chapter 8 Workshops and Maintenance General 1. Eye protection shall be worn at all times when operating power equipment and tools. 2. Report all equipment defects immediately. Do not use unsafe equipment
Mini Max 20 BAND SAW
OPERATING PROCEDURE FOR: Mini Max 20 BAND SAW SAFETY RULES: Warning: Willful violations of these safety rules, disruptive actions or horseplay may result in loss of the privilege to use the tools and machinery
SECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Table Breakdown 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 23 25 17 26 27 8 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK
7th/8th Grade Industrial Tech General Safety. Give your undivided attention to the machine in which you are using.
7th/8th Grade Industrial Tech General Safety Wood Lab Safety General Safety Always wear safety glasses. Report all injuries to the instructor. No baggy clothing or open toed shoes. Give your undivided
INDEX. General Shop safety Rules. Preventing Accidents. Rules for operating Equipment. Table Saw. Avoiding Kickback. Jointer.
General Shop safety Rules Preventing Accidents Rules for operating Equipment Table Saw Avoiding Kickback Jointer Thickness Planer Radial Arm-Saw Compound Mitre Saw Bandsaw Drill Press Router Table Belt/Disc
Machine Guarding. OSHA Office of Training and Education 1
Machine Guarding OSHA Office of Training and Education 1 Introduction Crushed hands and arms, severed fingers, blindness - the list of possible machinery-related injuries is as long as it is horrifying.
STUDENT/FACULTY MACHINE SHOP SAFETY RULES
STUDENT/FACULTY MACHINE SHOP SAFETY RULES Supervisors have full authority over the shop and its safe use, including the responsibility, authority, and obligation to prohibit shop or tool access for the
Model D1700/D1701 Moulding Head Instruction Sheet
Model D1700/D1701 Moulding Head Instruction Sheet Phone #: (360) 734-3482 Online Tech Support: tech-support@shopfox.biz Web: www.shopfox.biz To reduce risk of serious personal injury when using moulding
Home Workshop System WARNING. MARK V Model 500. Summary Manual. Designed and Built in Dayton, Ohio.
Shopsmith Mark V Home Workshop System MARK V Model 500 Summary Manual Designed and Built in Dayton, Ohio. WARNING Read the SAFETY information in the Introduction section and complete the ASSEMBLY AND ALIGNMENT
SAVINGS EVENT $ POWERMATIC PRIDE. Powermatic Sign Giveaway Free Accessories Price Reductions On All Products Save Even More with Rebates
POWERMATIC PRIDE SAVINGS EVENT PRICES EFFECTIVE JANUARY 1, 2009 TO APRIL 30, 2009 PRICES EFFECTIVE JANUARY 1, 2009 TO APRIL 30, 2009 Giveaway Free Accessories Price Reductions On All Products Save Even
North Dakota State University Power Tool Operations and Maintenance
North Dakota State University Power Tool Operations and Maintenance I. Introduction This NDSU procedure provides guidelines for the use of power tools. The intent is to establish proper safety procedures
CBM125 Cabinetmaking II Syllabus
CBM125 Cabinetmaking II Syllabus Course Information Credits 7 Campus Washburn Institute of Technology Address 5724 SW Huntoon City/State/Zip Topeka, Kansas 66604 Main Office Office Fax 785.670.2010 785.273.7080
Jointer. Given a properly adjusted jointer, instruction and demonstration of use, each student will be able to:
Jointer I. Competencies Given a properly adjusted jointer, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the jointer. B. Complete a written test on
23 WOODWORKING EQUIPMENT
23 WOODWORKING EQUIPMENT Chisel Mortiser Chisel mortiser... 1199 Cutting Machine Heavy duty band saw... 1197 Scroll saw... 1197 Dust Collector Dust collector... 1201 Overarm Router Overarm router... 1202
General Shop Safety. Work Area. General Safety. First-Aid. Hand Tool Safety 10/18/2011. Personal Protective Equipment
Work Area General Shop Safety Eastview High School Technology & Engineering Department Keep work area clean Assure area is well lit Be aware of bystanders and surrounding area Properly secure and support
SHOPSMITH MOLDING HEAD
INTRODUCTION The molding head is a practical easy-to-use saw accessory that enables you to add a professional touch to almost any project. With it, you can form table edges, cut cabinet door lips, make
Equipment Safety Briefings
Equipment Safety Briefings Table Saw Although the table saw is one of the most useful machines in the shop, it is also one of the most dangerous. It can be used to accurately rip and crosscut lumber and
25-200H. 12 Planer / Jointer. with Helical Cutterhead. Parts List.
25-200H 12 Planer / Jointer with Helical Cutterhead 4001824 Parts List www.rikontools.com CABINET ASSEMBLY PARTS EXPLOSION & PARTS LIST KEY NO. DESCRIPTION KEY NO. DESCRIPTION 1 Pan Head Screw M6x12 P25-200H-1
15% OFF ON SELECT POWERMATIC WOODWORKING MACHINES
-day sale SAVE UP TO an extra 1% OFF ON SELECT POWERMATIC WOODWORKING MACHINES A N D A C C E S S O R I E S T H E G O L D S T A N D A R D S I N C E 1 9 2 1 POWERMATIC.COM PRICES EFFECTIVE: NOVEMBER 2 TO
OPERATING RULES Clubhouse 4 Wood Shop
OPERATING RULES Clubhouse 4 Wood Shop A. Personal Safety 1. Dress properly for your work. Wear no loose jewelry, gloves, neckties, or loose clothing that could get caught in moving parts. 2. Non-slip,
ELECTRIC SLIP ROLL MACHINE. Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0
ELECTRIC SLIP ROLL MACHINE Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0 Operation Manual Table of contents I MAIN SPECIFICATION...2 II SAFETY INSTRUCTIONS.. 2 III OPERATION INSTRUCTIONS..4
ST1007/ST1012 PARTS ST1007
ST1007/ST1012 PARTS ST1007 Main Breakdown 30-7 30-8 30-10 30-9 30-1 30-3 30-6 30-2 30-4 30-5 82 83 84 77 78 79 80 30 60 59 58 62 64 61 46 44 63 66 65 55 56 26 45 27 45 27 25 43 37 41 50 42 72 73 51 53
Forename: Surname: School / College/ Institution. Course date: / / RDTHSC:
Specialist Extension Level S1HS Forename: Surname: School / College/ Institution Course date: / / RDTHSC: These Training and Accreditation Guidelines are based on the following essential publications:
Portable circular saw Used to cut a wide range of construction materials Check the cord, leads and 3 pin plugs for any damage. A Residual Current Device (RCD) is plugged into the power source. Do not stand
8 x 5 PLANER THICKNESSER OPERATING INSTRUCTIONS MODEL: W588
8 x 5 PLANER THICKNESSER OPERATING INSTRUCTIONS MODEL: W588 Charnwood, Cedar Court, Walker Road, Bardon, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 Email; sales@charnwood.net website;
Advanced Woods-CA-TS-v1.0 (Radial Arm Saw Safety Test) Preview Student Page 1 of 2 Preview Teacher Printed: 2/10/2014 Preview Course 211.
Advanced Woods-CA-TS-v1.0 (Radial Arm Saw Safety Test) Preview Student Page 1 of 2 Preview Course 211.1719 NAME: DATE: RADIAL ARM SAW SAFETY TEST Multiple Choice You may have to select more than one correct
OPERATOR'S MANUAL RULES FOR SAFE OPERATION
OPERATOR'S MANUAL #4950300 ROUTER AND JIG SAW MOUNTING KIT (FOR USE WITH THE BT3000 TABLE SAW) CONGRATULATIONS AND THANK YOU FOR BUYING THIS RYOBI ROUTER AND JIG SAW MOUNTING KIT. Your new #4950300 Router
SAFETY IS SPECIFIC POWER TOOL. Guidelines for the safe operation of widely used portable, and stationary power tools ADVISORY GROUPS W ARNING
POWER TOOL SAFETY IS SPECIFIC Guidelines for the safe operation of widely used portable, and stationary power tools D A N G E R ADVISORY GROUPS Underwriters Laboratories, Inc. American National Standards
Hazard Identification and Risk Assessment Form. Risk Assessment
Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. Equipment mostly used by the. Selected trainees would
PRACTICAL TASK MANUAL
6706-28 Level 2 Diploma in Wood Machining for Joinery Manufacture PRACTICAL TASK MANUAL July 2014 Version 1.0 Contents Candidate details 2 Unit assessment overview 3 Practical task completion record 3
TABLES SAWS Laguna Fusion 10 tablesaw Laguna Platinum 10" Tablesaw Laguna Platinum Dovetail 10 Tablesaw BANDSAWS Laguna 14 Bandsaw 14 Twelve Laguna LT14 SUV Bandsaw Laguna 18 Bandsaw LT 18 3000 PLANERS
OWNER S MANUAL CT058 8 JOINTER
OWNER S MANUAL CT058 8 JOINTER Index General Safety Instructions Page 3 Specific Safety Instructions Page 4 CT058 Jointer Features Page 5 Illustrated Features Page 6 Unpacking Page 7 Assembly Assembling
A P P R O V E D $ Item (29 x 29 ) Reg. $320.00
PRINTED IN CANADA Prices are in effect from October 1 st, 2008 to February 28 th, 2009 WE RESERVE THE RIGHT TO CORRECT ANY TYPOGRAPHICAL AND PICTORIAL ERRORS WITHOUT NOTICE. Distributed by QUALIT Y A P
(Signed original copy on file)
CFP 215-2 STATE OF FLORIDA DEPARTMENT OF CF PAMPHLET CHILDREN AND FAMILIES NO. 215-2 TALLAHASSEE, July 1, 1999 Safety SAFE PRACTICE GUIDELINES FOR OPERATING AND MAINTAINING MACHINERY AND EQUIPMENT Elimination
Shipyard Machinery and Power Tool Safety. A Hazard Prevention Course. Conducted By The Port of San Diego Ship Repair Association. (Including Guarding)
Shipyard Machinery and Power Tool Safety (Including Guarding) A Hazard Prevention Course Conducted By The Port of San Diego Ship Repair Association This material was produced under grant SH-31243-SH7 from
Circular Saw MODEL MT581. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH Circular Saw MODEL MT58 005337 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
KANSAS CITY WOODWORKERS GUILD SHOP RULES & GUIDELINES
KANSAS CITY WOODWORKERS GUILD SHOP RULES & GUIDELINES 1. The Director of Assets is responsible for overall coordination of the Shop and has the authority to stop activities not believed to be consistent
Durham Woodworking Club. January 25, 2016
Durham Woodworking Club January 25, 2016 The drill press has primarily been a metal working machine since its first incarnation. The purpose of the modern day drill press has been to provide woodworkers
Programme-Based Engagement
Programme-Based Engagement Contents 1. Introduction 03 2. Understanding Hand and Finger Amputations Caused by Machines 03 3. Machines Commonly Involved in Hand and Finger Amputations 04 4. What Must be
CATALOGUE WOOD WORKING JET HAS 50 YEARS EXPERIENCE IN WOOD WORKING MACHINES SOLID CONSTRUCTION FOR ACCURACY AND LONG LIFE
Jet products are Swiss customised and built to a high standard of accuracy. Cast iron construction ensures a lifetime of reliable performance WOOD WORKING CATALOGUE JET HAS 50 YEARS EXPERIENCE IN WOOD
Hazard Identification and Risk Assessment Form. Risk Assessment
Identification and Assessment Form Assessment Current Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module.
OLIVER MACHINERY. Revised 5/2017 $ Catalog 2017 Oliver Machinery
OLIVER MACHINERY $2.00 i Revised 5/2017 table of contents OLIVER HISTORY Tradition and Innovation... 1 MACHINES 2018 18 Classic Lathe... 2 4016 10 Table Saw... 3 4045 12 Table Saw... 4 4060 16 Table Saw...
ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
INDUSTRIAL RIP FENCE SYSTEM MODELS KRF-10/30L12-30 CONTRACTOR SAWS KRF-10/52L12-52 CONTRACTOR SAWS KRF-100/T50L12-50 CABINET SAWS INSTRUCTION MANUAL COPYRIGHT C 2000 ALL RIGHTS RESERVED BY KING CANADA
General Wood Shop Notes
General Wood Shop Notes Restricted Materials No METAL or BONE of any kind on any machine or in the room o See additional restrictions individual machine All reclaimed and other than new lumber must be
Hand Tools: General information:
Hand Tools: General information: The Greatest hazards posed by hand tools result from misuse and improper maintenance. Safety requires that the floor be kept as clean and dry as possible to prevent accidental
Model W1837 (For Machines Mfd. Since 8/18) PARTS. Main PARTS -83-
-83- Main 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 113 96 90 91 92 93 95 96 97 98 100 101 102 103 104 105 106 109
CHAPTER 52 ELECTRICAL POWER TOOLS
CHAPTER 52 ELECTRICAL POWER TOOLS HOW TO CHOOSE AND USE THEM The Types and Uses pages provide you with a list of the electrical power tools found in the pioneer tool outfit. These pages should help you
Health & Safety Policy and Procedures Manual SECTION 5 HAND AND POWER TOOLS
SECTION 5 HAND AND POWER TOOLS 1. POWER TOOLS A. References: 29 CFR 1926 Sub Part I (300-307) B. Employees using hand and power tools and exposed to the hazard of falling, flying, abrasive, and splashing
Forename: Surname: School / College/ Institution. Course date: / / RDTHSC:
Specialist Extension Level S8HS Forename: Surname: School / College/ Institution Course date: / / RDTHSC: These Training and Accreditation Guidelines are based on the following essential publications:
SAWS JET 10 Proshop Tablesaw JET 14 Industrial Bandsaw JET 18 Bandsaw PLANER/THICKNESSERS JPT260M Jet Combo Planer/Thicknesser JPT310 Jet Combo Planer/Thicknesser JML1014I Jet Combo Planer/Thicknesser
Health and Safety Training in Design and Technology Design and Technology Association Specialist Extension Level S8HS Planer/Thicknesser Machines
Specialist Extension Level S8HS Forename: Surname: School / College/ Institution Course date: / / These Training and Accreditation Guidelines are based on the following essential publications: Health and
PARTS. Base Cabinet & Motor PARTS. Model W1745W (For Machines Mfd. Since 9/16) V2 22V2-3 22V2-4 22V2-1 22V2-2
Model W1745W (For Machines Mfd. Since 9/16) Base Cabinet & Motor 22V2-1 22V2-2 22V2-5 22V2-9 22V2-8 22V2-7 22V2-6 22V2-3 22V2-4 22V2 23 24 26 25 46 47 48 49 44 45 15 14 16 17 50 18 13 12 11 7 20 9 8 9
BOWLING GREEN STATE UNIVERSITY SCHOOL OF ART WOODSHOP MANUAL
BOWLING GREEN STATE UNIVERSITY SCHOOL OF ART WOODSHOP MANUAL WRITTEN BY: CLAYTON PETERSON HANS RUEBEL LEONARD TAYLOR 1 1. GENERAL REFERENCE...5 1.1 Introduction... 5 1.2 Machine vs. Hand... 5 1.3 Rip-cuts...
Tools Hand and Power. OSHA Office of Training and Education 1
Tools Hand and Power 1 Hazards Workers using hand and power tools may be exposed to these hazards: objects that fall, fly, are abrasive, or splash harmful dusts, fumes, mists, vapors, and gases frayed
MODEL T " HELICAL CUTTERHEAD INSTALLATION INSTRUCTIONS
MODEL T27696 12" HELICAL CUTTERHEAD INSTALLATION INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction The Model T27696 indexable
10 BANDSAW OPERATING INSTRUCTIONS MODEL: W715
Machinery & Tooling at its best! 10 BANDSAW OPERATING INSTRUCTIONS MODEL: W715 Charnwood, Cedar Court, Walker Road, Bardon, Leicestershire, LE67 1TU Tel. 01530 516926 Fax. 01530 516929 email; sales@charnwood.net
10 x 6 Planer/Thicknesser
01550 10 x 6 Planer/Thicknesser Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. 1 Specifications 2 Safety Rules.3-4 Unpacking.5
RYOBI 10 IN (254 MM) TABLE SAW MODEL NO. BT REPAIR SHEET
RYOBI 0 IN (2 MM) TABLE SAW MODEL NO. BT00- REPAIR SHEET 2 RYOBI 0 in. (2 mm) TABLE SAW - MODEL NO. BT00- FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP
Yale Environmental Health & Safety
Yale Environmental Health & Safety Equipment/Task Name: Equipment/Task Hazard Class: Shop Name: PANEL SAWS 4 http://ehs.yale.edu/forms-tools/toolclassification-matrix Shop Hazard Class: Purpose Panel saws
Powermatic Model 31A Combination Belt-Disk Sander
OPERATING PROCEDURE FOR: Powermatic Model 31A Combination Belt-Disk Sander INTRODUCTION: The combination belt-disk sander is used to sand the edges of boards. It can be used to smooth the edge or to remove
University of Tennessee Safety Guidelines
University of Tennessee Safety Guidelines Program Subject: Hand and Power Tool Safety Guidance Approval Date: 12/1/2016 Next Scheduled Review: 6/1/2020 Date Effective: 12/1/2016 Contact Information: Program
Angle Grinder MODEL 9553B MODEL 9555B
ENGLISH Angle Grinder MODEL 9553B MODEL 9555B 006649 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR
TH E MARK OF COMPLETE PLANER SATISFACTION
TH E MARK OF COMPLETE PLANER SATISFACTION SINGLE SURFACE PLANER DO U B L E SCREW-ADJUSTED CAPACITY 20" BED x 8",dea' for small shopsr millsr pattern shopsr schoo'sr 'umber yards - as an auxiliary p'aner
SECTION 10: PARTS. Main Model G0771Z (Mfd. Since 09/16)
SECTION 10: PARTS Main 96 103 105 119 104 120 102 101 124 29-1 29-4 29-2 29-5 29-3 29-6 29-7 29-8 29-9 29-10 97 98 99 121 100 106 97 98 99 100 121 96 29 27 28 125 24 25 26 30 53 41 40 39 31 34 114 115
RYOBI 10 in. (254 mm) TABLE SAW MODEL NO. BT3100 REPAIR SHEET
RYOBI 0 in. (4 mm) TABLE SAW MODEL NO. BT00 REPAIR SHEET FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP FENCE ASSEMBLY, REFER TO FIGURE C FOR MOTOR ASSEMBLY,
G5959Z 12" Left-Tilting Table Saw -37-
Date Serial Number GROUND. 329 401 403 411 ALWAYS USE GUARDS AND ANTI-KICKBACK DEVICES 401 107 106 152 406 404 405 408 138 412 410 409 402 151 101A 139 144 143 140 142 141 114 101B 137 108 102 103 128A
INDEX. 110 powermatic.com. Accu-Fence Assembly for PM Accu-Fence Rear-Lock Assembly 12. Accu-Fence Side Panel Replacement Kit 12
INDEX A Accu-Fence Assembly for PM2000 10 11 Accu-Fence Rear-Lock Assembly 12 Accu-Fence Side Panel Replacement Kit 12 Accu-Fence System 30" 10 15 Accu-Fence System 50" 10 15 B Bandsaw, 14" PWBS-14 26
OPERATOR'S MANUAL ROUTER MOUNTING KIT
OPERATOR'S MANUAL MOUNTING KIT 4950301 (FOR USE WITH BT3000 AND BT3100 TABLE SAWS) Your new router mounting kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of
CELEBRATION $ STOCK NO $ STOCK NO K STOCK NO T H E G O L D S T A N D A R D S I N C E
T H E G O L D S T A N D A R D S I N C E 1 9 2 1 CELEBRATION PM1200 Air Filtration SysteM 379 99 STOCK NO. 1791330 SEE PAGE 12 FOR DETAILS PM2000 10" CABINET SAW 2899 99 STOCK NO. 1792000K SEE PAGE FOR