Shark Guard Installation

Size: px

Start display at page:

Download "Shark Guard Installation"

Brooke Harper
6 years ago
Views:

1 Shark Guard Installation

2 In the Package When you receive your Shark Guard, verify that nothing was damaged in shipping. Here is a current list of parts that should be included with this Craftsman packages. The guard Clamp and knob assembly Three different height splitters 6 MM Phenolic knob Shark face decals Other accessories you may have ordered

3 Splitters Lets start with the splitters. This is the heart of this guard system and will be used most often. I suggest you apply some Johnson's Paste wax or Minwax Paste wax to the Splitters. This should be done periodically to clean and protect the splitters and to slick up the surfaces to reduce friction. DISCONNECT THE POWER SOURCE. NEVER COUNT ON YOUR SWITCH ALONE TO CONTROL THE POWER WHEN WORKING ON MACHINERY. THEY CAN FAIL. Currently, these splitters are designed to mount very much like your OEM blade guard. It utilizes the mounting bolt and splitter bracket behind the saws rear fence rail. These saws came with a 6 mm threaded screw and a wing nut. We supply a nice phenolic knob that makes it a bit easier to secure the splitters to the bracket. Remove any splitter or guard that you have mounted now, by removing the mounting bolt and washer. If you have the original washer, this will be used under the new knob that came with the shark package. The tallest splitter is for use with the thickest stock. These were designed to utilize the full blade depth with the Shark Guard in place. The medium splitter is for use on regular cutting such as sheet goods, 1 by and 2 by material. It is imperative that you use the correct splitter for the material that you are cutting. Feeding the wrong thickness material can be dangerous. It can stop material in mid cut. Always check or adjust the guard height for material being cut.

4 There are warning labels on all SGK1 shark guards that serve to help as a reminder to do this for you and others who may use the saw. If you have an older Shark Guard, send me an and I will get a warning label with instructions mailed to you. Consult your owners manual for installation instructions for the splitters. It will be the same basic thing for the Shark splitters.

5 Splitter Alignment At this point of setup you will need to align or verify alignment of the splitter to the blade. Install your blade if you have removed it earlier. You will need to use a straight edge, steel ruler, framing square or something similar. Refer to your Operator's Manual. Shorty Splitter Your Shark Guard comes with a short splitter. This is to utilize when you can't have the larger splitters or the guard in place. Removal of the guard and splitter is a necessity for doing some sawing operations on your saw. Short dado's and rabbet cuts are examples. This short splitter is also helpful in the prevention of kickbacks. It serves three functions. It helps to prevent the saw kerf from closing in on itself and grabbing the rear teeth of the blade. It assists in maintaining the width of the stock from the fence to the blade and helps prevent twisting of this stock into the rear teeth of the blade. This solution is not as elegant as a riving knife would be, but still serves and important function. To help prevent kickback.

6 The Clamp assembly Once you have the medium or tall splitter securely installed and aligned, you can install your throat plate. Install this according to you Operator's manual. The three slots on the top of the two largest splitters are used with this clamp. The three steel pins in the lower portion of the clamp slip into these slots and lock down when the knobs of the clamp are tightened. There are also set screws in one clamp half that serve to keep the two clamp halves parallel when tightening regardless of splitter thickness. You loosen the knobs and slide the clamp toward the rear of the saw and lift up. Installation is the reverse. This clamp helps to prevent lifting of the material depending on material thickness being cut. Feeding the wrong thickness material can be dangerous. It can stop material in mid cut. Always check or adjust the guard height for material being cut. Make certain the correct splitter for each cut is installed.

7 Use the correct splitter for the material If you are cutting approximately 1.5 inch or thinner stock, the middle sized splitter should be used. The tallest one is only for cutting thicker material. This keeps the guard closer to the work so that dust collection efficiency is maximized. The pawls are designed for each height splitter, so they also work best when this rule is followed. Using the tallest splitter at all times is not the ideal setup for these.

Using the tail hook The Shark Guard has a horizontal hooked slot at the rear and a vertical slot further forward.

There is a safety hook that slips down over the rear stud to keep the guard from coming off when not intended.

on the front stud and brass bushings. This ability is beneficial when measuring between the fence and blade with a steel rule.

8 Using the tail hook The Shark Guard has a horizontal hooked slot at the rear and a vertical slot further forward. These slots are the mounting slots for this guard. The hooked slots get hooked on the rear studs of the clamp. There is a safety hook that slips down over the rear stud to keep the guard from coming off when not intended. You can see in this image that the guard can be left in the upward position by hooking only the rear slots and resting the guard on the front stud and brass bushings. This ability is beneficial when measuring between the fence and blade with a steel rule. The front slots just slip down over the front studs with care taken to use the smaller bushing diameters. With this done and your tail hook swung down into place, your blade guard is installed.

9 Using the Shark Guard Here is a link to some video's that help to show how these guard are intended to be used. Watch the videos that deal with splitters. This guarding system is designed to collect maximum dust during a cut, so the front roller underneath always rides on the stock. This helps prevent dust from getting slung forward by the blade on most cuts except at the very end of the cut and when cleaning up an edge. All guards with dust collection have trouble in those areas. If you ordered a guard with a dust port, a dust collection hose can be hooked up to the top of the guard using a hose clamp or just by slip fit. The dust port to hose connection is usually a snug fit. I suggest that something be done to the port though. If left open, you can get a fountain effect of sawdust right into your face. For a good fit with something that is readily available, spray paint tops will serve as a good cap for the 2.5 inch dust port. Larger ports might be capped using various plastic lids or tops.

10 Dust collection installations Rockler, Woodcraft and other outlets sell nice clear flex hose that fit these dust ports very well. If you leave the hose as a slip fit without a clamp, the hose can conveniently do duty on a router table as well. If you are installing a larger hose, you should also include a blast gate in line and easily accessible. This really is a requirement for 4 inch ports and is a good idea for smaller ones. When you will be cutting material that will have a small offcut, the suction from the dust port can be so powerful that it will lift the small parts and it can get thrown into the dust hose or into the front of the guard with extreme force. This is undesirable and easily prevented with a blast gate. There are numerous ways the you can support the hose for the dust collection. On my Gallery page, you will see some photo's of different setups. On my Review page, you will find links to individual websites where some owners used varied methods of supporting this hose. Here is a link with information on mounting the SGK1 overhead.

11 Shark face decal application The decals come in two parts. The mouth and the eye. If you are looking at the shark from the front, the decals go in on the left side. We recommend that you use Windex (any glass cleaner) and a soft cotton cloth like a T-shirt to clean the guard first. It may help to look at a photo like this one below. Remember, you are looking at the reverse side in this image. This was done so that you wouldn't have to handle the decal when moving the shark. It also gives is a nice appearance from the outside of the lexan. These are water slide decals. Below are the instructions for applying these. Place decal into a cup of clean water for seconds and remove when the thin decal film begins to slip along backing. (Discard backing material after the decal has been removed) Apply decal to clean surface. Here is a link to a PDF file that you can print out. It will help you get the proper placement for these. Just print page two. Lay the guard down on the image and then you will be able to place the decals on the inside where they should go. Once you have them in position, gently pat the decals dry with a soft cloth or towel going from one side to the other. Insure there are no air bubbles under the decals. They should dry in a matter of hours. Decal placement file.

12 Care and cleaning of the Shark Guard For splitters and riving knives, I suggest paste wax like Johnson's or Minwax to both clean and smooth the surfaces for less friction. On the guards we like to use Windex and a soft cloth to periodically keep the guard clear. Dust can build up inside and out, so it provides the best visibility when clean. Replacement parts Replacement, spare or upgrade parts can be ordered using this link. If you don't find what you need there, then just send an . Still have questions or concerns? If you have any questions about installation, setup or usage of this blade guard or parts associated with it, please don't hesitate to contact us. We are happy to help insure your satisfaction and safe usage of these products. Thanks a bunch and I hope that you enjoy using your Shark Guard.

Shark Guard Installation

Shark Guard Installation In the Package When you receive your Shark Guard, verify that nothing was damaged in shipping. Here is a current list of parts that should be included with a Dewalt 746 saw packages.