southpaw enterprises, inc.

Size: px
Start display at page:

Download "southpaw enterprises, inc."

Transcription

1 Store these instructions in a safe place or with the enclosed maintenance checklist In-FUN-ity Climbing System Assembly Examples This example sheet is intended to supplement the instruction sheets that come with each individual In-FUN-ity product. The In-FUN-ity system is modular, which allows you to purchase one, or many of the individual pieces, and it can be expanded at any time. The flexibility of the system makes it very challenging to have a set of instructions that explain how it all goes together, since, theoretically, every In-FUN-ity system might be assembled differently. Not pictured here are the In-FUN-ity Scooter Board Ramp, Rock Wall, or Rope. These can be placed virtually anywhere there is a ladder. The following pages will illustrate a few of the many ways that an In-FUN-ity system can be configured, and gives a big picture view of the assemblies. Together with the individual instruction sheets, this supplement should ease the process of building your system Illustration #1 is the basic In-FUN-ity Wall Ladder (Item # , , ). These part numbers differ only in the type of hardware that comes with the ladder, which is dependent on the type of wall that the ladder will be attached to. This is the foundation for the rest of the system. It is 31 wide and 81-1/2 high. Illustration #2 shows the In-FUN-ity Expansion Kit (Item # ), assembled (but not yet attached to the ladder). It is shown with the Wall Ladder because this item is not a stand-alone item, but must attach to a Wall Ladder. It is 31 wide, and 51 long, and will land approximately 55 from the wall when assembled to the Wall Ladder. If you look closely, you can see two sets of holes at the top. The top portion is intended to attach to the ladder with the set of holes closest to the Wall Ladder, but either set could be used. Illustration #3 shows the In-FUN-ity Jungle Gym Extender (Item # ). The illustration shows two pieces, the smaller of which will be shipped unassembled. It assembles in two minutes with the included screws and a hexwrench. The illustration also shows how the two pieces go together. It will extend an Expansion Kit by 51 Illustration #4 is designed to show how the Wall Ladder and Expansion Kit assemble to one another. In this configuration, the two sets of inside holes on the overhead piece of the expansion kits go unused. This is because, at any time, the overhead part may be expanded with one or two Jungle Gym Extenders, which will utilize the holes. Illustration #5 depicts the assembly of a Wall Ladder to an Expansion Kit with a Jungle Gym Extender. Note how the assembly from illustration #3 fits right into the end of the expansion kit. This system would extend 8 10 away from the wall. Illustration #6 depicts the assembly of a Wall Ladder to an Expansion Kit with TWO Jungle Gym Extenders. This configuration is approximately 13 feet in length. Illustration #7 begins to show the true versatility of the In-FUN-ity system. Shown here is a Wall Ladder, an Expansion Kit with one Jungle Gym Extender, and a second Expansion Kit. The second expansion kit can be added to either side, and hooks on with the In-FUN-ity Right Angle Adapter (Item # not shown). It is a simple hook that bolts to the end of the expansion kit and hooks onto an Expansion Kit or Jungle Gym Extender. Illustration #8 shows a large, more complex and MORE FUN system! The possibilities become endless. Pictured are one Wall Ladder, three Expansion Kits, two Jungle Gym Extenders and two Right Angle Adapters (not shown). Illustration #9 depicts a large, fairly complex In-FUN-ity system. Pictured are one Wall Ladder, six Expansion Kits, 5 Jungle Gym Extenders, four right angle adapters (not shown), and one In-FUN-ity Hook-On-Ladder (see below). At a customer s request, we added the In-FUN-ity Hook-On-Ladder (Item # ), a single ladder that can hook onto any Expansions Kit or Jungle Gym Extender without the overhead piece. This is simply to point out that Expansion Kits can be chained together without a Jungle Gym Extender, if desired.

2

3

4 Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. TM In-FUN-ity Wall Ladder - Brick / Block Wall Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 1 - Ladder Top Section (6 rungs) 1 - Hardware Kit Containing: 1 - Ladder Bottom Section (4 rungs) 4-1/4-20 Anchors 6-3/8-16 x 1-1/2 Button Head Cap Screws 8-1/4 Fender Washers 6-3/8 Flat Washers 4-1/4 Internal Tooth Lock Washers 1-7/32 Hex Key 4-1/4-20 x 1-3/4 Hex Head Cap Screws Maintenance Checklist The In-FUN-ity Climbing System is a modular system. Each instruction sheet is designed to assist you in assembling the particular item that it accompanies. Since these items may be configured in various manners to best suit your application, the instructions do not suggest any particular order of assembly. If you have any questions about how to set up your system, please contact Southpaw customer service for help. Working Load: 250 lbs. ASSEMBLY: Place the top and bottom sections of the ladder on the floor with the wall attachment boards on the floor. Position the BOTTOM top and bottom so that the three holes in TOP the bottom of the top section will be aligned with the three t-nuts in the top of the bottom section. Slide the top section into the bottom section as shown in picture at right. Be sure T-NUTS that the head of the screw holding the ladder rung slides into groove in the bottom section. Align the bolt holes with GROOVE FOR SCREW HEAD the t-nuts. Place a 3/8 flat washer on each of the 3/8 x 1-1/2 bolts. Start the bolts from the inside, through the holes in the top section and screw it into the t-nut in the bottom section. Start all six bolts then tighten securely with the hex key wrench provided. ATTACHING TO WALL: Position the assembled Therapy Ladder Wall against the wall where you wish to install it. Make sure that there are no obstructions such as electric outlets interfering with installation. Make a mark on the wall in the center of each of the four outside slots. This will determine where to drill for the anchors. Remove the ladder from the wall.

5 Using a power drill and a 1/2 diameter masonry bit, drill a hole as deep as the length of the anchor into the wall at each of the four marks. Vacuum the dust from the holes and insert the anchors until they are flush with the wall. Reposition the ladder on the wall and align the slots with the holes. Put one internal tooth lock washer then two fender washers on each bolt. Start a bolt into each of the anchors and tighten securely. MAINTENANCE CHECKLIST: All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer. MATTING PRECAUTIONS: Always use appropriate matting under and around equipment. STORAGE PROCEDURE: Make sure that equipment is not accessible by clients without proper supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using. Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. Southpaw Enterprises Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at FORM CODE: XI Southpaw Enterprises, Inc.

6 Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. TM In-FUN-ity Wall Ladder - Metal Stud Wall Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: Ladder Top Section (6 rungs) Hardware 1 - Hardware Kit Kit Containing: Kit Containing: Ladder Bottom Section (4 rungs) /4 1/4 1/4-20 x 3 x 3 Toggle Anchors Bolt Bolt Anchors /8-16 Connector x x 1-1/2 Screws Button Head Cap Screws /4 Fender Washers /8 5/32 Flat Hex Washers Key /4 Internal Tooth Lock Washers /32 Instruction Hex Key Sheet 4-1/4-20 x 1-3/4 Hex Head Cap Screws Instruction Maintenance Sheet Checklist Maintenance Checklist ASSEMBLY: The Position ASSEMBLY: In-FUN-ity the top Climbing and bottom System sections is a modular of the ladder system. on the Each floor instruction with the screw sheet holes is designed in the bottom to assist of the you top in section assembling facing Position particular up as the shown item top and that right. bottom it accompanies. sections of Since the ladder these items on the may floor be with configured the wall in attachment various manners boards to on best the suit floor. your Position appli- the cation, Check the top the that and instructions you bottom have so all do that the not the holes suggest three aligned. bolt any holes particular Start in the order bottom screws of of assembly. into the the top pilot section If you holes will have and be any aligned tighten questions all with of them about three securely how t-nuts to set using the up TOP SECTION your the top system, hex of the key bottom please provided. section. contact Southpaw Slide the top customer section service into the for bottom help. section as shown in picture at right. Be SCREWS sure that the BOTTOM head of the screw holding the ladder rung slides into groove in the bottom section. Align the bolt holes with the t-nuts. WORKING ATTACHING Place a 3/8 LOAD: flat TO washer WALL: 250 lbs. on each of the 3/8 x 1-1/2 bolts. Start the bolts from the inside, through the holes in the top section The Position Therapy and the screw assembled Ladder it into Wall Therapy the has t-nut four Ladder in the slots bottom Wall where against section. the toggle the TOP wall bolts where attach you the wish ladder to install to the it. wall. Make They sure are that positioned there are no to ASSEMBLY: obstructions accommodate such studs as on electric 16 or outlets 24 centers. interfering Position with installation. the assembled Therapy Ladder Wall against the wall where you wish The Place Therapy to the install top Ladder it. and Make bottom Wall sure has sections that two there sets of the are of slots no obstructions in each of the such mounting as electric boards. outlets BOTTOM These interfering will SECTION accommodate with installation. mounting Locate to ladder two studs adjacent on set the on floor either studs with 16 where the or wall 24 you centers. attachment want to put Using the a ladder. stud finding This tool, can be locate accomplished two adjacent using studs a stud where finder you tool. want Mark to mount the boards center the ladder. on of both the Mark floor. studs the at Position center 20-1/2 of the and these top 68-1/2 and studs from 20-1/2 the floor. and 68-1/2 Note: it from is very the floor. important Note: to it make is very your important mark at the to make exact T-NUTS bottom center your mark so of that the the studs. exact three Failure center holes to in of do the this bottom cause gle of bolts. the top unit This section to could become will cause be detached aligned the unit with from to become the studs. will result Failure in to diminished do this will holding result in power diminished of the holding toggle BOTTOM bolts. power This of the could tog- GROOVE wall resulting detached FOR SCREW in from injury HEAD the to wall users. resulting Drill an in 11/16 injury hole to into users. the studs Drill an at the each 11/16 three of diameter the t-nuts marks. in hole the Reposition through top of the the wall bottom ladder and the on studs the wall at TOP each and align of the the marks. slots with the holes. Remove the toggle wings section. from ATTACHING Remove the four the wings bolts. TO WALL: from the toggle bolts and put one internal tooth lock washer then two fender washers on each bolt. MAINTENANCE Position Put Slide the the bolts the top assembled through section CHECKLIST: the into Therapy proper the bottom slots Ladder section All obstructions wings of as the fold shown following back such toward fig. as wear electric 1. the points Be head sure outlets should of that the interfering be the bolt. checked with on installation. a monthly basis and recorded on the checklist enclosed. in the Wall mounting against the boards wall then where screw you wish the wings to install onto it. the Make bolts sure making that sure there that are the no head Make Reposition Check of a the mark that screw the on ladder all the holding screws wall on in the and the wall ladder bolts center and are rung align of tight. each the If bolts of any the with screws four the outside or holes. bolts slots. Push are found This on the will to bolts be determine loose, until the discontinue where wings to fold drill use back for until the and they anchors. through are into Remove tightened. the groove hole the in in the ladder the wall bottom from and the section. stud. wall. Using After pushing a power all drill four and bolts a 1/2 into diameter the holes, masonry use a screwdriver bit, T-NUTS drill a hole to tighten as deep each as go slides Align the bolt length Check securely. the bolt of wood holes the anchor surfaces with the into t-nuts. for the cracks wall at and each splinters. of the four If marks. cracks Vacuum are found, the discontinue dust from the use holes immediately and insert and the anchors contact until Place Southpaw they a 3/8 are flush flat Enterprises. washer with the on wall. Splinters each Reposition of may the be GROOVE the sanded ladder smooth FOR on the SCREW and wall refinished and HEAD align with the clear slots lacquer. with the holes. Put one Fig internal 1. 3/8 tooth MAINTENANCE x 1-1/2 lock washer bolts. CHECKLIST: then Start two the fender bolts from washers the on each bolt. Start a bolt into each of the anchors and tighten securely. inside, All of the through following the holes wear points the top should section be checked and screw on it a into monthly the t-nut basis in the and bottom recorded section. the Start checklist all six enclosed. bolts then tighten securely MAINTENANCE Check with that the all hex CHECKLIST: screws key wrench and bolts provided. are tight. If any screws or bolts are found to be loose, discontinue use until they All of are the tightened. following wear points should be checked on a monthly basis and recorded on the checklist enclosed. ATTACHING Check that TO all WALL: screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they Position are tightened. the assembled Therapy Ladder Wall against the wall where you wish to install it. Make sure that there are no obstructions Check such wood as surfaces electric for outlets cracks interfering and splinters. with the installation. If cracks are found, discontinue use immediately and contact The Therapy Southpaw Ladder Enterprises. Wall has Splinters two sets may of slots be sanded in each smooth of the and mounting refinished boards. with clear These lacquer. will accommodate mounting to studs with either 16 or 24 centers. Using a stud finding tool, locate the two adjacent studs to which you want to mount the ladder. Mark the center of these studs 20-1/2 and 68-1/2 from the floor. Note: it is very important to make your mark at the exact center of the studs. Failure to do this will result in diminished holding power of the toggle bolts. This could cause the unit to become detached from the wall resulting in injury to users.

7 Drill a 11/16 diameter hole through the wall and the studs at each of the marks. (Hint: You may wish to drill a smaller pilot hole and enlarge the hole with the 11/16 diameter bit). Remove the toggles from the bolts. Put one split lock washer and two fender washers on each bolt. Put a bolt through each of the slots from the front (the side with the ladder rungs). Screw the toggles back onto the bolts making sure that the wings of the toggle fold back toward the head of the bolt. Screw the bolt into the toggle until the end of the bolt is just through the toggle. (See Fig. 2 on reverse side). Reposition the ladder on the wall and align the slots with the holes. Fold back the wings on each bolt and push them through the holes in the wall. Tighten each bolt securely. Fig. 2 MAINTENANCE CHECKLIST: All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer. MATTING PRECAUTIONS: Always use appropriate matting under and around equipment. STORAGE PROCEDURE: Make sure that equipment is not accessible by clients without proper supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using. Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. Southpaw Enterprises Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at FORM CODE: XI Southpaw Enterprises, Inc.

8 Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. TM In-FUN-ity Wall Ladder - Wood Stud Wall Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 1 - Ladder Top Section 1 - Hardware Kit Containing: 1 - Ladder Bottom Section 4-5/16 x 3 Lag Screws 6-3/8-16 x 1-1/2 Button Head Cap Screws 8-5/16 Fender Washers 6-3/8 Flat Washers 4-5/16 Split Lock Washers 1-7/32 Hex Key Maintenance Checklist The In-FUN-ity Climbing System is a modular system. Each instruction sheet is designed to assist you in assembling the particular item that it accompanies. Since these items may be configured in various manners to best suit your application, the instructions do not suggest any particular order of assembly. If you have any questions about how to set up your system, please contact Southpaw customer service for help. Working Load: 250 lbs. ASSEMBLY: Position the top and bottom sections of the ladder on the floor with the wall attachment BOTTOM boards on the floor. Position the top and bottom so that the three bolt holes in the bottom of the top section will be aligned with the TOP three t-nuts in the top of the bottom section. Slide the top section into the bottom section as shown in picture at right. Be sure that the head of the screw holding the ladder T-NUTS rung slides into groove in the bottom section. Align the bolt holes with the t-nuts. GROOVE FOR SCREW HEAD Place a 3/8 flat washer on each of the 3/8 x 1-1/2 bolts. Start the bolts from the inside, through the holes in the top section and screw it into the t-nut in the bottom section. Start all six bolts then tighten securely with the hex key wrench provided. ATTACHING TO WALL: Position the assembled Therapy Ladder Wall against the wall where you wish to install it. Make sure that there are no obstructions such as electric outlets interfering with installation. The Therapy Ladder Wall has two sets of slots in each of the mounting boards. These will accommodate mounting to studs set on either 16 or 24 centers. Using a stud finding tool, locate two adjacent studs where you want to mount the ladder. Mark the center of these studs 20-1/2 and 68-1/2 from the floor. Note: it is very important to make your mark at the exact center of the studs. Failure to do this will result in diminished holding power of the lag bolts. This could cause the unit to become detached from the wall resulting in injury to users.

9 Drill a 1/4 diameter hole 2-1/4 deep through the wall and into the studs at each of the marks. Reposition the ladder on the wall and align the slots with the holes. Put one split lock washer then two fender washers on each bolt. Start a bolt into each of the holes and tighten securely. MAINTENANCE CHECKLIST: All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer. MATTING PRECAUTIONS: Always use appropriate matting under and around equipment. STORAGE PROCEDURE: Make sure that equipment is not accessible by clients without proper supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using. Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. Southpaw Enterprises Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at FORM CODE: XI Southpaw Enterprises, Inc.

10 Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. TM In-FUN-ity Scooter Board Ramp Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 1 - Ramp (Two pieces). 2 - Clamp Knobs 2 - Large 3/8 Washers Maintenance Checklist WORKING LOAD: 200 lbs The In-FUN-ity Climbing System is a modular system. Each instruction sheet is designed to assist you in assembling the particular item that it accompanies. Since these items may be configured in various manners to best suit your application, the instructions do not suggest any particular order of assembly. If you have any questions about how to set up your system, please contact Southpaw customer service for help. ASSEMBLY: Unpack all pieces of the ramp and place them on the floor. Position the two pieces as shown in fig.1, with the longer ramp piece laying top-side down. Align the holes for the knobs in the bent end of the top ramp piece with the holes in the ramp that have the threaded inserts. Place a 3/8 washer on each knob, then put the threaded end of the knob through the hole (fig.1) and screw it into the threaded insert (fig.2). Repeat this procedure on the opposite side of the ramp. Push the attachment piece down until the wood dowel is seated in the notch in the ramp and tighten the knobs. Turn the ramp over and attach the assembled ramp to the ladder wall by hooking the notch in the end of the top piece to the second rung from the bottom of the ladder. The inclined ramp may be used alone without attaching the top board. You may place it on the ladder at what you determine to be the appropriate height. THREADED INSERTS Figure 1 HOLE FOR KNOB MAINTENANCE CHECKLIST: All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Figure 2 Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer. MATTING PRECAUTIONS: Always use appropriate matting under and around equipment.

11 STORAGE PROCEDURE: For storage, loosen the knobs and fold the ramp in half. There is no need to completely unscrew the knobs unless you wish to separate the two pieces. Make sure that equipment is not accessible by clients without proper supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using. Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. Southpaw Enterprises Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at FORM CODE: XI Southpaw Enterprises, Inc.

12 TM In-FUN-ity Ladder Rock Wall Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 3 - Panels 27 x 27 w/ Screw Inserts 4 - Side Rails 2 - Connector Boards 12-1/4 x 2 Screws 8-3/8-16 x 1-1/2 Button Head Cap Screws 8-3/8 Flat Washers 1 - Set of 20 Handholds 1-5/16 Hex Key Wrench 1-7/32 Hex Key Wrench 1-4 mm Hex Key Wrench Maintenance Checklist Working Load: 200 lbs. The In-FUN-ity Climbing System is a modular system. Each instruction sheet is designed to assist you in assembling the particular item that it accompanies. Since these items may be configured in various manners to best suit your application, the instructions do not suggest any particular order of assembly. If you have any questions about how to set up your system, please contact Southpaw customer service for help. ASSEMBLY: Unpack and identify all of the parts. Read the instructions completely before starting assembly. It might be helpful to identify and lay out all of the parts in their proper position before starting actual assembly. Refer to illustrations on back page. Figure 1 shows the relationship of the side rail hole and screw with the holes in the panel. The panels have a series of two holes on the edge. One hole is for the heavy-duty connector screw, the other is left over from the machining process and will not be used. Figure 2 shows the relationship of the top panel with the top side rail. The back side of the panel has the flange of the screw inserts visible. The hook on the top of the top side rails goes toward the back of the panel. Assemble one of the upper side rails to one of the panels as shown in fig. 2. Note: There is a recessed arrow on the front of each panel - this arrow should point upwards when assembled. Line up edge holes in the panel with holes in the upper side rail, press the panel into the groove, and secure with two screws. These screws should go into the holes closest to the edge of the panel. Tighten each screw securely using the hex key wrench provided. Insert the middle panel into the upper side rail with the recessed arrow on the panel pointing towards the panel already attached. Line up the edge hole of the panel with the remaining hole in the upper side rail. Tighten another 1/4: screw (fig. 3) securely. Position one of the bottom halves of the side rails on the center panel. NOTE: There are two screw inserts in the bottom of the top rail and the top of the bottom rail. Position the bottom rail as shown in figs. 4 and 5. Start and tighten a screw in the top screw hole of the bottom rail to secure it to the center panel. Position the bottom panel in the groove of the bottom side rail, making sure the recessed arrow points towards the other two panels. Line up the edge holes with side rail holes. Start and tighten both screws. Put a 3/8 flat washer on four of the 3/8 x 1-1/2 cap screws. Position the connector board over the joint between the top and bottom side rails with the straight edge toward the back with the holes in the board aligned with the screw inserts in the side rails as shown in fig.6. Put one of the 3/8 bolts into each of the holes in the connector board and screw them into the corresponding screw insert in the side rails. Tighten securely using the hex key wrench provided. Assemble the rails and connector board to the opposite side in the same manner. Hang the Rock Wall on the appropriate ladder rung of the Ladder Wall or Ladder Wall Expansion Kit. Attach the handholds to the panels using the appropriate bolts. Note that some of the handholds have a v shape at the top of the hole. Use the matching flathead screws for these handholds. Others will have a flat at the bottom of the hole. Use the socket head cap screws to attach these handholds. All handhold attachment screws must protrude through the back of the screw insert a minimum of 3/4. Various shapes and sizes of handholds can be attached the wall in different positions to vary the degree of difficulty in climbing. The handholds are color-coded, with the green being easiest, yellow is medium difficulty, and red is difficult.

13 SAFETY WARNING: Do not allow children to go around the back side of the Ladder Rock Wall. The handhold bolts protrude and could cause an injury. MATTING PRECAUTIONS: Always use appropriate matting under and around The Rock Wall. MAINTENANCE CHECKLIST: All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer. STORAGE PROCEDURE: Make sure that equipment is not accessible by clients without proper supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using. Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. Southpaw Enterprises Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at FORM CODE: XI Southpaw Enterprises, Inc.

14 TM In-Fun-ity Expansion Kit Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 1 - Vertical Ladder (2 pieces) 6 - Tapcon Screws 1/4 x 1-1/4 1 - Horizontal Section 2 - Button Head Cap Screws 3/8-16 x 1-1/ Button Head Cap Screws 3/8-16 x 1-1/2 2 - Acorn Nuts 3/ /8 Flat Washers 1-7/32 Hex Key Wrench 2 - Angle Brackets Wood Screws #8 x Maintenance Checklist Your hardware will be packed with the Horizontal section WORKING LOAD: 300 LBS The In-FUN-ity Climbing System is a modular system. Each instruction sheet is designed to assist you in assembling the particular item that it accompanies. Since these items may be configured in various manners to best suit your application, the instructions do not suggest any particular order of assembly. If you have any questions about how to set up your system, please contact Southpaw customer service for help. ASSEMBLY: Position the top and bottom sections of the ladder on the floor. Position the top and bottom so that the three bolt holes in the bottom of the top section will be aligned with the three t-nuts in the top of the bottom section. Slide the top section into the bottom section as shown in Fig. 1. Be sure that the head of the screw holding the ladder rung slides into groove in the bottom section. Align the bolt holes with the t-nuts. Place a 3/8 flat washer on six of the 3/8 x 1-1/2 bolts. Start the bolts from the inside, through the holes in the top section and screw it into the t-nuts in the bottom section. Start all six bolts then tighten securely with the hex key wrench provided. Figure 1 Figure 2 Figure 2-A NOTE: IF YOU HAVE PURCHASED A JUNGLE-GYM EXTENDER, REFER TO THAT INSTRUCTION SHEET AT THIS TIME, AND ATTACH THE EXTENTIONS BEFORE MOVING ON. Position the top of the assembled ladder inside one end of the horizontal section and align the screw inserts (Figs. 2 & 2 A). Put a 3/8 flat washer on each of four of the 3/8 x 1-1/2 cap screws. Start a screw through each of the holes and into each screw insert. Tighten all four screws securely using the hex key wrench provided. Raise the assembled ladder and horizontal section and position the available end of the horizontal section against the wall ladder with the sides of the horizontal section on the outside of the wall ladder (Fig. 3). Align the holes in the outside boards with the screw inserts. Put a 3/8 flat washer on four of the 3/8 x 1-1/2 cap screws and put them through the holes in the board and start them into the screw inserts. Tighten all four screws securely using the hex key wrench provided. Figure 3

15 Two angle brackets are provided to attach the bottom of the vertical ladder to the floor. Position the bracket on the floor on the outside of the ladder leg with the small holes on the floor. Put one of the 3/8 x 1-1/4 cap screws through the large hole in the bracket and through the hole in the bottom of the ladder. Put a 3/8 flat washer on the bolt then start a 3/8 acorn nut onto the bolt. Making sure that the bottom of the bracket in parallel with the floor, Tighten the nut using a 9/16 wrench while holding the cap screw with the hex key wrench provided. Install the bracket on both sides of the ladder. Screws are provided to secure the bracket to either wood or concrete floors. For concrete floors, drill pilot holes using a 3/16 masonry drill bit using the holes in the bracket as a guide. Drill the pilot holes 1-1/2 deep. Vacuum the dust out of the holes and start the 1/4 x 1-1/4 concrete screws (blue) into each hole. Tighten securely using either a flat blade screwdriver or a 5/16 wrench. For wood floors, drill pilot holes 1 deep using a 3/32 drill bit. Use the wood screws provided to secure the brackets to the floor. Note: vinyl tile floors may have either wood or concrete underneath. Determine which before drilling. Figure 4 MAINTENANCE CHECKLIST: All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer. MATTING PRECAUTIONS: Always use appropriate matting under and around equipment. STORAGE PROCEDURE: Make sure that equipment is not accessible by clients without proper supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using. Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. Southpaw Enterprises Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at FORM CODE: XI Southpaw Enterprises, Inc.

16 Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. TM In-Fun-ity Jungle Gym Extender Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 1 - Horizontal Section 1 - Connector w/ Bar (Not Assembled) 2-1/4 x 2 Dowel Screws 1-7/32 Hex Key Wrench 16-3/8 Flat Washers mm Hex Key Wrench 16-3/8-16 x 1-1/2 Button Head Cap Screws Maintenance Checklist WORKING LOAD: 250 lbs. NOTE: This item is intended for use if you already have the Southpaw In-FUN-ity Wall Ladder with the Expansion Kit # We recommend that you use a maximum of two Extenders with the Expansion Kit for a total of twelve feet. The In-FUN-ity Climbing System is a modular system. Each instruction sheet is designed to assist you in assembling the particular item that it accompanies. Since these items may be configured in various manners to best suit your application, the instructions do not suggest any particular order of assembly. If you have any questions about how to set up your system, please contact Southpaw customer service for help. Figure 1 ASSEMBLY: 1. You will have one loose wood dowel, and two loose pieces of wood. These pieces constitute the part labeled Connector with Bar. The wood pieces have a recess on one side that fits the wood dowel. Push the wood dowel into this recess and screw the 1/4 x 2 wood screw into the pre-drilled hole in the end of the dowel Using the smaller of the hex key wrenches (4.0 mm). Repeat on the other end, making sure the two ends line up. 2. Put a flat washer onto each of the 16 button-head cap screws. 3. If your Expansion Kit is not already assembled to your Wall Ladder, line up the Jungle-Gym Extender with the identical part from the Expansion Kit. Fit the connector piece in-between the two, lining up all 16 holes. From the inside of the connector piece, put a button head cap screw w/ washer into each hole and tighten. Then continue with your Expansion Kit instructions. 4. If your Expansion Kit is already assembled to your Wall Ladder, remove the vertical ladder from the end of your Expansion Kit (Fig. 1). Lay aside the four screws and washers as they will be used to re-attach the ladder to the extender. 5. Position the connector piece with the wood dowel inside the sides of the Expansion Kit boards in place where the vertical ladder was attached. Align the holes of the connector with the screw inserts. Put a 3/8 x 1-1/2 cap screw w/ washer through the hole in the connector and start it into the screw insert. Do not tighten at this time. Start a bolt into each of the four holes on each side of the connector (Fig. 2). After all eight bolts are started, tighten each one securely using the hex key wrench provided. Figure 3 Figure 2 Figure 4

17 6. Attach the vertical ladder to one end of the extender using the four screws that were taken out when you removed it (Fig. 3). Tighten all screws securely. 7. Raise the assembled ladder and horizontal section. Slide the available end of the extender into position with the side boards of the extender on the outside of the connector piece (Fig. 3). Align the holes in the connector with the screw inserts. Put a bolt through each of the holes in the connector and start the bolt into the screw insert. Do not tighten until all of the bolts are started then tighten them securely using the hex key wrench provided. MAINTENANCE CHECKLIST: All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer MATTING PRECAUTIONS: Always use appropriate matting under and around equipment. STORAGE PROCEDURE: Make sure that equipment is not accessible by clients without proper supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using. Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. FORM CODE: XI Southpaw Enterprises Inc Southpaw Enterprises, Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at southpawenterprises.com

18 Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. TM In-Fun-ity Expansion Kit Right Angle Connector Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 2 - Connector Hooks 4-3/8-16 x 1-1/2 Socket Head Cap Screws 4-3/8 Flat Washers 1-7/32 Hex Key Wrench Maintenance Checklist NOTE: This item is intended for use if you already have the Southpaw In-FUN-ity Wall Ladder with the Expansion Kit # or Jungle Gym Extender # The hooks will allow you to attach an extender kit to your system out at a right angle to the existing structure. The In-FUN-ity Climbing System is a modular system. Each instruction sheet is designed to assist you in assembling the particular item that it accompanies. Since these items may be configured in various manners to best suit your application, the instructions do not suggest any particular order of assembly. If you have any questions about how to set up your system, please contact Southpaw customer service for help. ASSEMBLY: Assemble the Extender Kit following the instructions provided. Attach the Right Angle Connectors to the end of the horizontal section opposite the ladder. Put a 3/8 flat washer on each of the 3/8 x 1-1/2 cap screws. Put a screw through the hole in the connector and start it into the screw insert from the inside of the of the horizontal section as shown above. Start all four screws then tighten securely using the hex key wrench provided. Attach the Extender Kit as shown above. MAINTENANCE CHECKLIST: All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer. MATTING PRECAUTIONS: Always use appropriate matting under and around equipment. STORAGE PROCEDURE: Make sure that equipment is not accessible by clients without proper supervision.

19 CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using. Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. Southpaw Enterprises Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at FORM CODE: XI Southpaw Enterprises, Inc.

20 TM In-FUN-ity Rope Store these instructions in a safe place or with the enclosed maintenance checklist Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 1-3/4 X 12 ft. rope Maintenance Checklist Fig. 1 ATTACHMENT INSTRUCTIONS: Put the loop end of the rope behind the ladder rung at the appropriate height. Put the tag end of the rope through the loop as shown in fig. 1. Pull on the tag end of the rope until the formed loop is tight around the ladder rung as shown in fig. 2. STORAGE PROCEDURE: Store where not accessible without supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Wipe rope with a damp cloth using mild soap and water or disinfectant. Dry before using. DO NOT machine wash. Fig. 2 MAINTENANCE CHECKLIST: Check that rope is secure on the ladder rung. Check for cuts. If cuts are found, discontinue use. Small whiskers developing on the rope are normal with use and not considered a hazard. Safety Precautions - The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their physical abilities. Use appropriate spotting / safety techniques. In addition, the layout of your activity area, proper installation and maintenance of your equipment is critical. Southpaw equipment is not intended for recreational or outdoor use. Under no condition should this equipment be used without proper supervision. This sheet is for example only. It is not meant to, in any way, replace local, county, state, or Federal standards. Be aware - it is your responsibility to find all pertinent safety information that pertains to your facility. Southpaw Enterprises Inc. If you have any questions or comments, please call or write Southpaw Enterprises, Inc. P.O. Box 1047, Dayton, Ohio Toll Free - (800) Come see us on the World Wide Web at FORM CODE: XI Southpaw Enterprises, Inc.

21 TM In-FUN-ity Hook-On Ladder Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file this in an accessible location: the must be read and familiar to anyone who is using Southpaw Enterprises Equipment. IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping. If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. MATERIALS LIST: 1 - Vertical Ladder (2 pieces) 6 - Wood Screws #8 x Button Head Cap Screws 3/8-16 x 1-1/2 6 - Tapcon Screws 1/4 x 1-1/4 2 - Button Head Cap Screws 3/8-16 x 1-1/4 1-7/32 Hex Key Wrench 6-3/8 Flat Washers Angle Brackets 1 - Maintenance Checklist 2 - Acorn Nuts 3/8-16 WORKING LOAD: 200 lbs. ASSEMBLY: Position the top and bottom sections of the ladder on the floor. Position the top and bottom so that the three bolt holes in the bottom of the top section will be aligned with the three t-nuts in the top of the bottom section. Slide the top section into the bottom section as shown in Fig. 1. Be sure that the head of the screw holding the ladder rung slides into groove in the bottom section. Align the bolt holes with the t-nuts. Place a 3/8 flat washer on each of the six of the 3/8 x 1-1/2 bolts. Start the bolts from the inside, through the holes in the top section and screw it into the t-nuts in the bottom section. Start all six bolts then tighten securely with the hex key wrench provided. The pre-assembled top of the ladder (Fig. 2) will hook onto the side of the expansion kit. Angle brackets are provided to anchor the bottom of the ladder to the floor (Fig. 3). Fig. 1 Fig. 2 MAINTENANCE CHECKLIST: Fig. 3 All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed. Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they are tightened. Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer. MATTING PRECAUTIONS: Always use appropriate matting under and around equipment. STORAGE PROCEDURE: Make sure that equipment is not accessible by clients without proper supervision. CLEANING INSTRUCTIONS: Check with your infectious disease department before using these procedures. Check for client allergies first. Clean with a damp cloth using soap and water or disinfectant. Dry before using.

southpaw enterprises, inc.

southpaw enterprises, inc. southpaw enterprises, inc. Store these instructions with the enclosed maintenance checklist in a safe place. You may also access them on our website. Instruction Sheet Convertible Climbing Wall - Block/Brick

More information

southpaw enterprises, inc.

southpaw enterprises, inc. southpaw enterprises, inc. Instruction Sheet C-STAND 7100 Store these instructions in a safe place or with the enclosed maintenance checklist Take time to familiarize yourself with the use and maintenance

More information

southpaw enterprises, inc.

southpaw enterprises, inc. southpaw enterprises, inc. Store these instructions along with the enclosed maintenance checklist in a safe place. You may also access them on our website. Instruction Sheet: Fiber Optic Activity Panel

More information

southpaw enterprises, inc.

southpaw enterprises, inc. southpaw enterprises, inc. Store these instructions with the enclosed maintenance checklist in a safe place. You may also access them on our website. Instruction Sheet Wood Joist 2-1/2 Ft. Drop Ceiling

More information

southpaw enterprises, inc.

southpaw enterprises, inc. southpaw enterprises, inc. Store these instructions with the enclosed maintenance checklist in a safe place. You may also access them on our website. Instruction Sheet Prefab Joist 3 Ft. Drop Ceiling Kit

More information

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013 U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -

More information

southpaw enterprises, inc.

southpaw enterprises, inc. Eye Bolt Wrap 7001 Store these instructions with the enclosed maintenance checklist in a safe place. You may also access them on our website. this in an accessible location: the must be read and familiar

More information

GroundControl. Follow instructions contained in this manual. Incorrect installation could result in serious injury or damage to property.

GroundControl. Follow instructions contained in this manual. Incorrect installation could result in serious injury or damage to property. GroundControl TM use supplied hardware Use only hardware supplied in your GroundControl kit or supplied by an authorized YAKIMA dealer. Use of unauthorized parts in the GroundControl system could result

More information

Installation Instruction

Installation Instruction Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry

More information

southpaw enterprises, inc.

southpaw enterprises, inc. OSCAR S Playhouse 4400 this in an accessible location: the must be read and familiar to anyone 1 - Playhouse 1-1 - Maintenance checklist SETUP INSTRUCTIONS Fig. 1 Step 1: Butt Corners Step 2: Wrap Flaps

More information

Therma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit)

Therma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit) Swing Unit with Hardware Kit - Hardware Tools Included: 4mm Allen Wrench, 6mm Allen Wrench, 8mm T-Handle Allen Wrench (1) 3/4" Drill Bit, (1) 7/32" Drill Bit and Hole Template Guide Tools Required: Phillips

More information

19 to 39 TV WALL MOUNT - FULL MOTION

19 to 39 TV WALL MOUNT - FULL MOTION 19 to 39 TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...5

More information

Office Partitions WARNING. Assembly Instructions. Customer Service A S S E M B LY HARDWARE H1 H2 H3 H4 H5 H8 H9 H10 H11 H12

Office Partitions WARNING. Assembly Instructions. Customer Service A S S E M B LY HARDWARE H1 H2 H3 H4 H5 H8 H9 H10 H11 H12 Customer Service 1-800-645-2986 Assembly Instructions WARNING In order to prevent structural failure, instability, t i p - o v e r, and/or serious injury, please follow i n s t ructions care f u l l y.

More information

EASY POOL STEP (NE113)

EASY POOL STEP (NE113) EASY POOL STEP (NE113) FOR USE WITH: EASY POOL STEP (NE113) (1 CARTON) EASY POOL STEP WITH OUTSIDE LADDER (NE126) EASY POOL STEP ENTRY SYSTEM (NE138) (With Gate) (4 CARTONS) Above are the options available

More information

DX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations

DX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3

More information

Assembly Instructions Music Library System

Assembly Instructions Music Library System Assembly Instructions Music Library System 7-Shelf Unit is shown. 6-Shelf Unit assembly is the same except where noted. Contents Important User Information...........................2 General...2 Manufacturer...2

More information

Mount to the Wall INSTALLATION MANUAL

Mount to the Wall INSTALLATION MANUAL Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced

More information

ASSEMBLY AND CARE INSTRUCTIONS JUST FOR KIDS 355

ASSEMBLY AND CARE INSTRUCTIONS JUST FOR KIDS 355 ASSEMBLY AND CARE INSTRUCTIONS VERSION: 8920100 (Revised 06/16) JUST FOR KIDS 355 SALES AND SERVICE spiethamerica.com Canada and International 135 Forestview Road, PO Box 40 Orillia, Ontario, Canada L3V

More information

Please read these instructions before use and keep for future reference

Please read these instructions before use and keep for future reference Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com

More information

Independent Containment System (ICS)

Independent Containment System (ICS) Installing the Independent Containment System (ICS) Complete these instructions to install the Independent Containment System (ICS). Prerequisites This installation requires a team of at least two people.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com

More information

Install Instructions. NewAge Steel Welded Tall Locker

Install Instructions. NewAge Steel Welded Tall Locker Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x

More information

Model #SH & CH SH Pine CH Naturaline

Model #SH & CH SH Pine CH Naturaline Model #SH304-101 & CH304-101 Assembly Manual SH304-101 Pine CH304-101 Naturaline Component Parts A 2 ea. Angled Rail - 2 x 4 x 107-1/8" B 1 ea. Center Angled Rail - 2 x 4 x 107-1/8" C 9 ea. Rock Board

More information

Octagon Vinyl Gazebo Assembly Instructions

Octagon Vinyl Gazebo Assembly Instructions Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

Pleated Shades with Corded Top Down / Bottom Up Option

Pleated Shades with Corded Top Down / Bottom Up Option Pleated Shades with Corded Top Down / Bottom Up Option Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Congratulations on purchasing Pleated

More information

Worktop INDEX eight Capacity Unpacking

Worktop INDEX eight Capacity Unpacking Pro.0 Series Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of

More information

MOTORIZED STANDARD SHADE WITH CABLES Installation Instructions

MOTORIZED STANDARD SHADE WITH CABLES Installation Instructions Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench

More information

WALLBED Assembly Instructions

WALLBED Assembly Instructions WALLBED Assembly Instructions 1 Congratulations and a Big Thank You for your purchase of a Wallbed Gallery Murphy Bed! We sincerely appreciate your business! First a few words of advice and caution: 1.

More information

Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV

Showpiece Cabinet Integrated Stand For 32 - 52 LCD HDTV Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV

More information

Wall Mount Assembly and Mounting Guide (55 /84 )

Wall Mount Assembly and Mounting Guide (55 /84 ) Microsoft Surface Hub Wall Mount Assembly and Mounting Guide (55 /84 ) For mounting on a wall with wood studs These instructions assume wood-stud wall construction with 2-by-4 studs spaced 16 inches apart,

More information

Qwik-Fence Installation Instructions

Qwik-Fence Installation Instructions Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

Sales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd.

Sales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd. Sales & Service sasportonline.com SA Sport (Canada) SA Sport (U.S.A.) 135 Forestview Road 7879 Will Rogers Blvd. P.O. Box 40 Fort Worth, Texas Orillia, Ontario USA 76140 Canada L3V 6H9 Telephone: (705)

More information

Assembly Instructions for model: VMPR1

Assembly Instructions for model: VMPR1 Assembly Instructions for model: VMPR1 Congratulations on your purchase! The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design

More information

Assembly Instructions for Model: VMPL3

Assembly Instructions for Model: VMPL3 Assembly Instructions for Model: VMPL3 Thank you for choosing a Sanus Systems VisionMount Wall Mount. The VMPL3 is designed to hold 27-84 Flat Panel LCD or Plasma Displays weighing up to 280 lbs. It will

More information

INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000

INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with

More information

Installation Guide PMWT-660/680. Projector Wall Mount

Installation Guide PMWT-660/680. Projector Wall Mount Installation Guide PMWT-660/680 Projector Wall Mount for SMART Board TM interactive whiteboards Trademark Notice SMART Board and the SMART logo are trademarks of SMART Technologies Inc. TORX is a trademark

More information

ROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door

ROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are

More information

User Instructions Multiline Otter Scoreboard Caddy Assembly

User Instructions Multiline Otter Scoreboard Caddy Assembly List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)

More information

GearBoss AirPro Locker

GearBoss AirPro Locker Installation and Owner s Instructions GearBoss AirPro Locker Wall Installation Island Installation Contents Important User Information...........................2 General...2 Manufacturer...2 Intended

More information

NX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP

NX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP 6-1/4 HANDRAIL W/ VINYL HANDGRIP TYPICAL ASSEMBLY 5 2 BUTT JOINT 12 10 9 1 8 11 6 3 7 4 BUTT JOINT COMPONENT LIST 1 LEFT RETURN 7 UPPER IMPACT ABSORBER 2 RIGHT RETURN 8 LOWER IMPACT ABSORBER 3 OUTSIDE

More information

Closet Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls

Closet Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls Tools Required: Phillips Screwdriver (#2) Adjustable Wrench Level Tape Measure Utility Knife Electric Drill Drill Bits for Anchors Ladder (4 foot) Models TKA 5 Through TKA 14 Equipped with Footswitch Controls

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

GearBoss II High Density storage

GearBoss II High Density storage Assembly/Owner s Manual GearBoss II High Density storage contents Safety...........................................2 General......................................2 Installation...................................2

More information

BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms

BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away

More information

Universal flat-panel mount

Universal flat-panel mount I N S T A L L A T I O N M A N U A L Universal flat-panel mount www.christiedigital.com PM 2004/ REV 02 Contents - Assembly drawing - Fine tune tilt adjustments - Parts list - Installing the adapter plate

More information

Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions

Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry

More information

Track Rack. * Track Racks are not lockable

Track Rack. * Track Racks are not lockable The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply

More information

LPR System Installation instructions

LPR System Installation instructions Toll LPR System Installation instructions 1 General Information The following installation instructions should be used as a guide for installing Folding Guard LPR System. Good common sense and appropriate

More information

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B

More information

Gared Pro Portable Backstop

Gared Pro Portable Backstop Models: 5016, 5017, & 5018 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units PUBLICATION NO. 551754436 SAVE THESE

More information

INSTRUCTION BOOKLET #C20

INSTRUCTION BOOKLET #C20 INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO

More information

INSTALLATION OF THE TRACK FOR THE STRAIGHT SIDE STEEL LADDER

INSTALLATION OF THE TRACK FOR THE STRAIGHT SIDE STEEL LADDER ASSEMBLY OF THE 7180 STRAIGHT SIDE STEEL LADDER TOOLS REQUIRED FOR ASSEMBLY SAFETY GLASSES (2) 1 / 2 WRENCHES OR SOCKETS STEP LADDER OF APPROPRIATE HEIGHT (2) 7 / 16" WRENCHES OR SOCKETS HACKSAW FLAT HEAD

More information

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

ALL SEASON PATIO COVER

ALL SEASON PATIO COVER ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the

More information

Gared Pro-S Portable Backstop

Gared Pro-S Portable Backstop Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

TrendWall Floor-To-Ceiling Panels Installation Instruction

TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster

More information

WARNING: Failure to follow these warnings and assembly instructions could

WARNING: Failure to follow these warnings and assembly instructions could OXFORD BUNK BED TWIN OVER TWIN & FULL OVER FULL For Bunk Bed Twin Over Twin WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. To help prevent

More information

MPA-9000 Universal Ceiling Projector Mount Kit

MPA-9000 Universal Ceiling Projector Mount Kit I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low

More information

Giraud Tool Company, Inc.

Giraud Tool Company, Inc. Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade

More information

Installation Instructions - Model V4JSD 1

Installation Instructions - Model V4JSD 1 Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)

More information

PFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS

PFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS 9531-007-Z00-01 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Wood Stud Installation 5 Concrete Surface Installation

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

TP4463. ASSeMBly INSTruCTIONS FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3

TP4463. ASSeMBly INSTruCTIONS FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3 TP63 FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3 Flat Panel TV Stand Stand with TV Mounting System Stand with Wall Mount ASSeMBly INSTruCTIONS for your safety, please follow these precautions:!

More information

ASSEMBLY OF THE KNOCKED-DOWN LADDERS: 8 to 12 STEPS STANDARD TOP AND SAFELOCK REQUIRED TOOLS

ASSEMBLY OF THE KNOCKED-DOWN LADDERS: 8 to 12 STEPS STANDARD TOP AND SAFELOCK REQUIRED TOOLS ASSEMBLY OF THE KNOCKED-DOWN LADDERS: 8 to 12 STEPS STANDARD TOP AND SAFELOCK REQUIRED TOOLS SAFETY GLASSES 7/16" WRENCH OR SOCKET STEP LADDER OF APPROPRIATE HEIGHT (2) 9/16" WRENCHES OR SOCKETS RUBBER

More information

Assembly and installation help

Assembly and installation help Assembly and installation help A supplement to the directions The Purpose of this tutorial is to expand (not replace) upon the directions that come with the system and to help provide shortcuts, the first

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

INSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY

INSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY NEWAGE STEEL WELDED CABINETRY WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES ALL CABINETS MUST BE MOUNTED TO STUDS ON A SECURE WALL, AS PER THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS

More information

OPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

OPERATOR'S MANUAL 46 SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.

More information

Safety Guidelines and Assembly Instructions

Safety Guidelines and Assembly Instructions Play Action Air Rider TM Safety Guidelines and Assembly Instructions Maximum Weight Limit: 210 pounds We re Here To Help! Call Toll Free 1-888-752-9782 Customer Service: Monday - Friday, 8:00 A.M. to 5:00

More information

INSTALLATION AND CARE INSTRUCTIONS

INSTALLATION AND CARE INSTRUCTIONS INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from

More information

MX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP

MX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP 6-1/4 HANDRAIL W/ VINYL HANDGRIP TYPICAL ASSEMBLY 5 2 BUTT JOINT 12 10 9 1 8 11 6 3 7 4 BUTT JOINT COMPONENT LIST 1 LEFT RETURN 7 UPPER IMPACT ABSORBER 2 RIGHT RETURN 8 LOWER IMPACT ABSORBER 3 OUTSIDE

More information

ALUMA-CLASSIC FENCE W1716 & W1720 INSTRUCTION MANUAL

ALUMA-CLASSIC FENCE W1716 & W1720 INSTRUCTION MANUAL ALUMA-CLASSIC FENCE W1716 & W1720 INSTRUCTION MANUAL Phone: Phone: 1-360-734-3482 On-Line On-Line Technical Technical Support: Support: tech-support@woodstockint.com tech-support@shopfox.biz COPYRIGHT

More information

The Festival Assembly Instructions

The Festival Assembly Instructions The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New

More information

MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER

MODEL# SLA001-3 SLIDE & LOCK A-FRAME POOL LADDER MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER IMPORTANT INSTRUCTIONS: : Read all instructions carefully & completely to become familiar with parts, assembly, safety and proper use of this product.

More information

Cabinet Storage Products

Cabinet Storage Products Assembly Instructions Storage Products (UltraStor, Acoustis, Adjustable Shelf, Cover Panels, Closure Panels) Wood Compartment Doors Full Wood Door Compartment Grille Doors Full Grille Door No Doors Contents

More information

INS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System

INS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with

More information

For additional assistance call

For additional assistance call The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or

More information

INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger

INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.

More information

Stuff-Your-Stuff Platform Bed (Twin and Full)

Stuff-Your-Stuff Platform Bed (Twin and Full) Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete

More information

INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER

INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER 6-1/2" 5" 2-7/16" 3-7/16" Ø2-7/8" 4-7/8" 11" 2" 3/16" 1/2" HORSESHOE W/ BAR S P ECIFICATIONS PARTS AND TOOLS Tools Needed Tape Measure Pencil

More information

RLP Flat Track Hardware sliding door hardware/ barn door track

RLP Flat Track Hardware sliding door hardware/ barn door track Page 1 of 9 Installation Suggestions for: RLP Flat Track Hardware sliding door hardware/ barn door track Read these instructions to end before starting installation or ordering hardware. Reclaimed Lumber

More information

ETX Powered Loudspeaker Accessories

ETX Powered Loudspeaker Accessories ETX Powered Loudspeaker Accessories ETX-BRKT10, ETX-BRKT12, ETX-BRKT15, ETX-TCA-S, ETX-TCA-L, and ETX-BRKT35 en Installation Guide en 3 Table of contents 1 Safety 4 2 Installation 6 2.1 Wall mount bracket

More information

Monoprice Adjustable Tilt/Swivel Flat Panel Wall Mount Model MLB-109B/RLB-102B (PID# 4926)

Monoprice Adjustable Tilt/Swivel Flat Panel Wall Mount Model MLB-109B/RLB-102B (PID# 4926) Monoprice Adjustable Tilt/Swivel Flat Panel Wall Mount Model MLB-109B/RLB-102B (PID# 4926) VESA Compliant up to 770x480 Max Weight: 125lbs UNPACKING INSTRUCTIONS Carefully open the carton, remove the contents

More information

Pillar Hanger ASSEMBLY INSTRUCTIONS

Pillar Hanger ASSEMBLY INSTRUCTIONS Pillar Hanger ASSEMBLY INSTRUCTIONS PILLAR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket

More information

PHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns

PHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns PHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns Features: Durable high quality gloss black baked on powder coat finish Fits

More information

PFW Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids

PFW Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids Maximum Flat Panel Weight: 100 lb. / 45.35 kg. Included Components Wall Mount (Qty 1) Extension Bracket (Qty 1 Pair) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver

More information

NX7 SERIES 5-1/2 HANDRAIL

NX7 SERIES 5-1/2 HANDRAIL STORAGE & HANDLING The handrails are shipped unassembled. Upon receipt, immediately check all material for any damage that may have occurred in transit and verify that all of the items and quantities are

More information

Assembly Instructions

Assembly Instructions Assembly Instructions 10 CONTRACTOR TABLE SAW Model No. 351.218330 Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 31624.00 Draft (10/08/09) UNPACKING The

More information

SHELTON THERMOSTATIC SHOWER PANEL

SHELTON THERMOSTATIC SHOWER PANEL SKU(s): 413241 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor,

More information

LOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page

LOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit

More information

BLYTHE BUNK BED TWIN OVER TWIN

BLYTHE BUNK BED TWIN OVER TWIN pottery barn kids BLYTHE BUNK BED TWIN OVER TWIN www.potterybarnkids.com Date: 2014-Sept.-25 Page 1 of 11 WARNING:. Failure to follow these warnings and assembly instructions could result in serious injury

More information

Strata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at

Strata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at 1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel

More information

NUMBER OF HORIZONTALS REQUIRED FOR 2 ON CENTER SPACING.

NUMBER OF HORIZONTALS REQUIRED FOR 2 ON CENTER SPACING. K WIK FRAME ASSEMBLY INSTRUCTIONS NUMBER OF HORIZONTALS REQUIRED FOR 2 ON CENTER SPACING. APPROXIMATE DOOR LEAF WEIGHT (LBS.) WITH 29 GAUGE STEEL PANEL ALL PACK AGES INCLUDE #235 STEEL GIRT 2 FT. ON CENTER

More information

3/8-16 x 3/4 cap screw. 3/8-16 hex nut for above screws. 1/4-20 x 3/4 socket cap screw. 3/16 short arm hex key (not to scale)

3/8-16 x 3/4 cap screw. 3/8-16 hex nut for above screws. 1/4-20 x 3/4 socket cap screw. 3/16 short arm hex key (not to scale) Super Slab Roller 24, 30 and 36 models Worktable Assembly Directions P.O. Box 89 Cheney, WA 99004 USA 509.235.9200/800.23.7896 Fax: 509.235.9203 www.northstarequipment.com Revised September, 2006. All

More information

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

L.L.Bean. Wooden Slat Bed

L.L.Bean. Wooden Slat Bed L.L.Bean Wooden Slat Bed Thank you for purchasing our Slat Bed. Assembly of this product requires A Phillips head screwdriver. We have found it helpful to have a second person present in at least one step

More information

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM The only table saw fence with Automatic Positioning Control TM OWNER S MANUAL Please read this owner s manual before use and keep it at hand for reference. Note: The INCRA TS II system consists of three

More information