ASTM E 283, ASTM E 547, AND ASTM E 330 TEST REPORT. Rendered to: SIMPSON DOOR COMPANY

Transcription

1 ASTM E 283, ASTM E 547, AND TEST REPORT Rendered to: SIMPSON DOOR COMPANY SERIES/MODEL: Simpson Door Fir 1501 PRODUCT TYPE: Wood Inswing Door with Side Lites Report No: Test Date: 04/02/04 Report Date: 05/31/05 Expiration Date: 04/02/ Derry Court York, PA phone: fax:

2 ASTM E 283, ASTM E 547, AND TEST REPORT Rendered to: SIMPSON DOOR COMPANY 400 Simpson Avenue McCleary, Washington Report No: Test Date: 04/02/04 Report Date: 05/31/05 Expiration Date: 04/02/08 Project Summary: Architectural Testing, Inc. (ATI) was contracted by Endura Products, Inc to perform tests on a Series/Model Simpson, wood inswing door with side lites. This report is a reissue of the original Report No This report is reissued in the name of Simpson Door Company through written authorization of Endura Products, Inc. Test specimen description and results are reported herein. Test Specifications: The test specimen was evaluated in accordance with the following: ASTM E , Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors. ASTM E , Water Penetration of Exterior Windows, Skylights, Doors and Curtains Walls by Cyclic Static Air Pressure Difference. -97, Structural Performance of Exterior Windows, Curtain Walls, and Doors by Static Air Pressure Difference. Test Specimen Description: Series/Model: Simpson Door Fir 1501 Type: Wood Inswing Door with Side Lites Overall Size: 9' 4-3/4" wide by 6' 10-1/2" high Door Size: 3' 0" wide by 6' 8" high Side Lite Size (2): 3' 0" wide by 6' 8-1/2" high Finish: The wood was unfinished. 130 Derry Court York, PA phone: fax:

3 Page 2 of 5 Test Specimen Description: (Continued) Glazing Details: The active door panel and fixed side lites utilized 1/8" thick tempered glass. The glass was interior glazed against a bed of silicone and secured with a wood glazing bead. The glazing bead was fastened to the interior perimeters with 5/8" long brad nails spaced 1" from the corners and 6" on center. Active Door Panel Construction: The active door panel was constructed of wood members. The stiles were attached to the top and bottom rails utilizing wood glue and tongue and groove joints. A door sweep was attached to the bottom rail of the door utilizing two 3/16" by 1/2" "U" shaped staples two at each end and 10" on center. The door panel utilized three hinges located from the top of the door panel 9", 38", and 67". The hinges were attached to the door stile with four #8 x 1" Philips head wood screws per hinge and attached to a vertical mullion with two #8 x 1" and two #8 x 2-1/2" Philips head screws per hinge. Side Lite Panel Construction: The side lite panels were constructed of wood members. The stiles were attached to the top and bottom rails utilizing wood glue, tongue and groove joinery and dowel pins. The panels were attached to each jamb and vertical mullions with four #8 x 2-1/2" drywall screws spaced 6" from the top and bottom and 22" on center. The top rails were attached to the horizontal mullion with two #8 x 2-1/2" drywall screws 5" from ends. The bottom rails were attached to a snap-in vinyl up-stand threshold leg with silicone. The interior perimeter of both side lites were secured with a vinyl glazing bead and 1" brad nails 2" from ends and 10" on center. The exterior perimeter was sealed with silicone. Mullion Construction: The vertical mullions were constructed of wood members. The vertical mullions were attached to the threshold and the head with two #8 x 2-1/2" drywall screws each. Buck Installation: The test unit was installed into 1-1/2" plywood frame and secured with #8 x 2-1/2" drywall screws 6" from ends and 22" on center at the jambs. The head was secured with #8 x 2-1/2" drywall screws 5" from ends and 19" on center. The exterior #2 Spruce-Pine-Fir test buck was secured to the interior plywood frame with #8 x 3" drywall screws spaced 6" from the corners and 10" on center in a staggered pattern around the exterior perimeter. The exterior and interior perimeters were sealed with silicone.

4 Page 3 of 5 Test Specimen Description: (Continued) Weatherstripping: Description Quantity Location Kerf mounted foam filled 1 Row Perimeter of active door vinyl single fin gasket Foam filled vinyl pad 1 Row Bottom corner vertical mullion at hinge and latch stiles Hardware: Test Results: Description Quantity Location Brass keyed knob 1 42" from bottom of latch stile with adjacent strike Brass keyed dead bolt /2" from bottom of latch stile with adjacent strike Brass hinges 3 From the top of hinge stile 9", 38", and 67" The results are tabulated as follows: Test Method Title of Test Results Allowed ASTM E 283 ASTM E 547 Air Infiltration 1.57 psf (25 mph) 0.03 cfm/ft 2 N/A Water Resistance 3.75 psf No leakage No leakage Uniform Load Deflection (Indicators were located on the vertical mullion) 25.0 psf (positive) 0.14" N/A 28.0 psf (negative) 0.12" N/A

5 Page 4 of 5 Test Results: (Continued) Test Method Title of Test Results Allowed Uniform Load Deflection (Indicators were located on the top corner door leaf) 25.0 psf (positive) 0.68" N/A 28.0 psf (negative) 0.27" N/A Uniform Load Structural (Indicators were located on the vertical mullion) 37.5 psf (positive) <0.01" N/A 42.5 psf (negative) <0.01" N/A Uniform Load Structural (Indicators were located on the top corner door leaf) 37.5 psf (positive) 0.15" N/A 42.5 psf (negative) 0.08" N/A This report is reissued in the name of Simpson Door Company through written authorization of Endura Products, Inc. to whom the original report was rendered. The original Endura Products, Inc. Report No. is Representative samples of the test specimen and a copy of this report will be retained by ATI for a period of four years from the original test date. This report is the exclusive property of the client so named herein and is applicable to the sample tested. Results obtained are tested values and do not constitute an opinion or endorsement by this laboratory. This report may not be reproduced, except in full, without the approval of Architectural Testing, Inc. For ARCHITECTURAL TESTING, INC: John C. McClane Technician Steven M. Urich Senior Project Engineer JCM:vlm

6 Page 5 of 5 Revision Log Rev. # Date Page(s) Revision(s) 0 05/31/05 N/A Original report issue - Reissue Report No in the name of Simpson Door Company