TECHNICAL MANUAL PLEATED BLINDS

Transcription

1 TECNICAL MANUAL PLEATED LINDS EN

2 Table of Contents Pleated lind Types of pleated blinds 4 Color 5 Control of pleated blinds 5 Care instructions for pleated blinds 6 Child Safety 7 Photometric values 8 Types of Fixation 9 Pre-Tensioned pleated blinds VS 10 Freehanging pleated blinds F 28 Roof pleated blinds DFC 40 Pleated blinds for conservatories PL 44 Pleated blinds shapes SD and SR 58 A brand symbolizing years of tradition, innumerable investments into research and development, use of high-quality materials, technological advancement, reliable work of hundreds of employees and many more parameters, which together form one whole-the fi nal product of the company ISOTRA. 2

3 PLEATED LINDS Pleated blinds Elegant element of modern interior Many atypical shapes ide range of pleated materials, colors, patterns and printing Fabrics with various light permeability, black-out fabrics, reflective fabrics and PEARL fabrics Optional combination of two fabrics Variable control system cord, handle, profile 3

4 Types of pleated blinds Types of pleated blinds Pre-tensioned pleated blinds VS 1 VS 2, VS 2 KL VS 3, VS 3 SD VS 4 Slope, VS 4 Slope S VS 5, VS 5 SD VS 6, VS 6 SD VS 7, VS 8 VS 9, VS 9 D VS 10, VS 10 D Types of window opening Vertical indows, Tilt and Turn indows, alcony Doors Freehanging pleated blinds F 1 F 2 F 3 F Slope 1 F Slope 2 FD Slope 3 F 7 F 8 Vertical indows, Tilt and Turn indows, alcony Doors Roof DF Comfort pleated 10blinds DFC 10 DFC 20 DFC 30 Roof windows Pleated blinds for conservatories PL 11 PL 30 PL 31 PL 32, PL 32 D PL 33, PL 33D PL 40 PL 41, PL 42 Conservatories Pleated blinds shapes SD and SR SD 2 SD 3 SR 1 S Triangular and Circular indows 4

5 PLEATED LINDS Color ead and bottom rail 01 Plastic Components 02 grey 05 black 12 black Other RAL and DECORAL colors of profile are at extra charge. Control Control by cord lock with possibility of additional guidance (for F pleated blinds) Control by plastic handle Control by operating rod Control by operating rod (for types VS and PL pleated blinds) without joint with joint (for PL pleated blinds) (for PL pleated blinds) Control by profile (for types DFC pleated blinds) Control by operating rod (for DFC pleated blinds) 5

6 Care Instructions for Pleated linds 1 2 Pleated fabrics are easy to clean. 3 4 max. Simply wash the blind in a solution of warm water of max. 30 C and a mild detergent. Rinse thoroughly, push the fabric into stack and carefully squeeze the water out until the blind does not drip any longer. ang the blind up in closed position. Open and close the blind several times while allowing it to dry to prevent the pleats sticking together. DO NOT IRON! This excludes all metallised fabrics as well as coated black out fabrics and 1-qualities. These can be carefully wiped clean with a cloth. Do not rub! e advise against chemical or ultrasonic cleaning an do not accept warranty claims in such cases. 5 6 e advise against chemical or ultrasonic cleaning an do not accept warranty claims in such cases. 12 Std. Product Information Operation For a long-lasting pleating it is necessary to operate your pleated blind regularly and also to fully raise the blind for longer periods. Especially when the pleated blind is exposed to high temperatures (eg southfacing windows, roof-lights, conservatories etc.), above practise is important to repeatedly support the pleats. Cleaning Frames and Glass For cleaning window frames and glasspanes do not use any caustic or alkaline detergents which may encounter directly or indirectly (condensation water) with the blind. Insufficient air ventilation (please see fitting instructions for min. mounting spaces) can cause condensation water. arranty does not apply to damages to the fabric caused by dripping water or insect excrements. Exterior Usage Pleated blinds are designed for heated interior locations only and not for exterior usage or swimming baths. Therefore no warranty is given for exterior installations, on open or partly glazed roofed areas or swimming baths. 6

7 PLEATED LINDS Important notes on child safety Guidelines for child-safe fitting of cord and chain operated pleated blinds Young children and can be strangled by loops in cords that operate the blind. There is a risk that cords may become wrapped around a child s neck.! To avoid strangulation and entanglement, keep cords out of the reach of young children. Move beds, cots and any furniture away from window covering cords. Do not tie cords together. Make sure cords or chains do not twist and create a loop. To reduce the risk of such accidents, please install and use supplied safety devices according to the fitting instructions. Complies with EN Child safety is a top priority during the selection and installation of sun protection products. hen selling and installing, certain points must be considered to ensure a standardised and therefore child-safe fitting. For queries, please contact the respective specialist. They will gladly explain about the possible risks and ensure professional measuring and installation. For a child-safe installation the head rail (cord outlet) must be fittet at least 1500 mm from the floor. The installation height of our products must be indicated on each order. If the installation height is not specified, the child safety of our products cannot be guaranteed. Please keep the safety information and fitting instructions that you received with the delivery of pleated blind. This cord winder must be securely fixed to an adjacent surface and the lowest point of the cord tassel must be at least 1500 mm from the floor. All cord operated blinds are supplied with a safety cord tassel. This opens up as soon as the cords are pulled apart 60 mm and at the same time pressure of 6 kg apply. Afterwards the assembly can be done by oneself according to the assembling instructions provided with the product. Model types F1, F2, F3, F7, F8, F Slope 1, F Slope 2, FD Slope 3, FD Slope 4: min mm! In case of cord operated blinds, cord winders must always be fitted and used. This cord winder must be securely fixed to an adjacent surface and the lowest point of the cord tassel must be at least 1500 mm from the floor. All cord operated blinds are supplied with a safety cord tassel. This opens up as soon as the cords are pulled apart 60 mm and at the same time pressure of 6 kg apply. Afterwards the assembly can be done by oneself according to the assembling instructions provided with the product. 7

8 Photometric values of pleated blinds The properties of pleated blinds in connection with light depend on many factors - for example, weave, coating, yarn selection, color, etc. These factors influence the optical and thermo-technical effects and ensure that each fabirc has different lighting values. The photometric values are spread on reflection, absorption and transmission. Together they add up to 100%. (Influences by ventilation, glass, assembly and assemble distance are not considered). Explanation of Terms Example: Fabric no REFLECTION 35% of the light is reflected by the fabric ASORPTION 25% of the light is absorbed by the fabric TRANSMISSION 40% of the light is transmitted through the fabric fabric window glass Reflection: The value of reflection indicates the amount of light reflected from the fabric. The more sunlight is reflected, the less it will remain in the room and the room is not so heated. Transmission - The value of transmission indicates the amout of light passing through the fabric. The higher the transmission value,the brighter the room. Absorption - The value of absorption indicates the amount of light absorbed by the fabric. The absorbed light energy is usually converted into heat. Pleated blinds for Computer orkplaces Transmission 20% N The intensity of sunlight varies from each of the four directions. Interior sunshades are designed to reduce the incoming sunlight. The maximum permissible transmission level according to EU guidelines is given as percentage for all four directions. Transmission 6% E 0 Transmission 6% S Transmission 5% 8

9 PLEATED LINDS Types of fixation CA - fixation to the wing (assembly to Fit to indow eading) C - fixation on the wing (assembly to frame using wall bracket) V - fixation on the wing without drilling (assembly to frame using clamp bracket 25 mm) KL fixation on the wing with adhesive bar L fixation on window bar 9

10 Important notes Attention! If Not Specified: Fabric = Rail End Caps Overlap! 2,5 mm 5 mm Distance etween lind and indow Pane = 5 mm! 5 mm 5 mm Several linds Side by Side: Light slit (fabric gap) between the blinds approx. 10 mm. Necessary rail distance is determined by the manufacturer. ca. 10 mm 10

11 PLEATED LINDS Pre-tensioned pleated blinds VS 11 Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

12 asic Product Specification Pleated blind Type VS 1 eight () min max min max mm 200 mm 1500 mm to width 1200 mm max mm eight () min max min max mm 200 mm 1500 mm to width 1200 mm max mm 22 mm Package eight lind eight Package eight 16,9 mm Fitting Situation: Vertical 500 mm ca. 50 mm 1000 mm ca. 60 mm 1500 mm ca. 70 mm 2000 mm ca. 80 mm 2200 mm ca. 90 mm 22 mm 16,9 mm Pleated blind Type VS 2 eight () min max min max 200 mm 1500 mm 200 mm 1500 mm to width 1200 mm max mm eight () min max min max 200 mm 1500 mm 200 mm 1500 mm to width 1200 mm max mm Package eight 22 mm lind eight Package eight 16,9 mm Fitting Situation: Vertical 500 mm ca. 50 mm 1000 mm ca. 60 mm 1500 mm ca. 70 mm 2000 mm ca. 80 mm 2200 mm ca. 90 mm : In 1.3 m width magnet holders in RAL are supplied. From 1.3 m width magnetic holders made with a galvanized surface are supplied. 22 mm 16,9 mm 12

13 PLEATED LINDS Pleated blind Type VS 3 Fitting Situation: Vertical : In case of using two fabrics the order of substances is always set such that the fabric with heavier weight is always basic fabric placed in upper part of the blind, and the fabric with lower weight is always additional fabric places in lower part of the blind. Pleated blind Type VS 3 SD Fitting Situation: Vertical : IIn case of using two fabrics the order of substances is always set such that the fabric with heavier weight is always basic fabric placed in upper part of the blind, and the fabric with lower weight is always additional fabric places in lower part of the blind. eight () min max min max mm 200 mm 1500 mm to width 1200 mm max mm eight () min max min max mm 200 mm 1500 mm to width 1200 mm max mm Package eight lind eight Package eight 500 mm ca. 90 mm 1000 mm ca. 100 mm 1500 mm ca. 110 mm 2000 mm ca mm ca. 130 mm 13 eight () min max min max mm 200 mm 2200 mm to width 1200 mm max mm eight () min max min max mm 200 mm 2200 mm Package eight lind eight Package eight 500 mm ca. 90 mm 1000 mm ca. 100 mm 1500 mm ca. 110 mm 2000 mm ca mm ca. 130 mm 22 mm 22 mm 22 mm 22 mm 22 mm 16,9 mm 18,5 mm 16,9 mm 16,9 mm 16,9 mm 16,9 mm 16,9 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

14 Pleated blind Type VS 2 KL eight () min max min max 200 mm 1500 mm 200 mm 1500 mm to width 1200 mm max mm eight () min max min max 200 mm 1500 mm 200 mm 1500 mm to width 1200 mm max mm Package eight lind eight Package eight 22 mm 16,9 mm Fitting Situation: Vertical 500 mm ca. 50 mm 1000 mm ca. 60 mm 1500 mm ca. 70 mm 2000 mm ca. 80 mm 2200 mm ca. 90 mm 5 mm 17 mm 6 mm : Assembly is made with clamping profiles directly on the glass. No drilling or screwing required. 22 mm 16,9 mm 14

15 PLEATED LINDS Measuring and assembly of pleated blinds VS 1, VS 2, VS 3, VS 3 SD Measuring to Fit to indow eading - CA fixation Order width Straight frame: Assembly to window bar (beading bracket) - L fixation Assembly to frame (using wall bracket) - C fixation d frame = Desired Overlap Assembly to frame (using clamp bracket 25 mm) - V fixation 21 mm 21 mm = 5 mm = Desired Overlap 15! Measure the width A at several points in case of possible frame size tolerances. Order width = A Order height = Order width = A minus 5 mm Order height = Measure the corners of the window bar. Order width = A plus 5 mm Order height = minus 18 mm Please pay attention to window furniture. Order width = A including overlap Order height = including overlap : Dimension = head rail. If you use top fix bracket and bracket you need further 4,5 mm. Check if the clamp bracket can be used regarding window mechanism and the distance to the window sill (strength of window wing max. 25 mm). Please pay attention to window furniture. Order width = A including desired overlap Order height = minus 10 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

16 General note Attention: If Not Specified: Fabric = Rail End Caps Overlap! 2,5 mm 5 mm Distance etween lind and indow Pane = 5 mm 5 mm 5 mm ca. 10 mm Several linds Side by Side: Light slit (fabric gap) between the blinds approx. 10 mm. Necessary rail distance is determined by the manufacturer. Measuring and assembly of pleated blinds VS 2 KL! Checking the width of seal D Measure the width of the seal D on all four sides for possible tolerances. D less than or equal 5 mm 5 mm 5 mm L/L Order width = light width LA minus 4 mm Order height = light height L minus 8 mm D D D more than 5 mm > 5 mm > 5 mm LG/LG Order width = light width of glass LGA plus 7 mm Order height = light height of glass LG plus 3 mm D D for assembly of pleated blinds VS 2 KL Glass panes must be dry and free of grease, silicone or other contaminants. The optimum temperature for work is between C (adhesive surface and surroundings). Air pocket inside the adhesive area is not a reason for complaint, unless disturbed functionality of profiles. 16

17 asic Product Specification Pleated blind Type VS 4 Slope Fitting Situation: Vertical Pleated blind Type VS 4 Slope S Fitting Situation: Vertical control control : reakage is pushed up to the sloping rail. Upper rail movement can not be operated by handle! Consider levelling chocks for sloping window frames! 17 PLEATED LINDS ase width Slope width eight 1 (D) eight 2 (C) min max max* min max min min max 300 mm 1500 mm 2300 mm 300 mm 1500 mm 100 mm 5 60 to width 1200 mm max mm *depending on fabric width ase width Slope width eight 1 (D) eight 2 (C) min max max* min max min min max 300 mm 1500 mm 2300 mm 300 mm 1500 mm 100 mm 5 40 to width 1200 mm max mm *depending on fabric width Package eight lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 2200 mm ca. 100 mm 22 mm ase width eight 1 () eight 2 (C) min max min max min min max 300 mm 1000 mm 300 mm 2200 mm 100 mm ase width eight 1 () eight 2 (C) min max min max min min max 300 mm 1000 mm 300 mm 2200 mm 100 mm Package eight lind eight Package eight 500 mm ca. 70 mm 1000 mm ca. 80 mm 1500 mm ca. 90 mm 2000 mm ca. 100 mm 2200 mm ca. 110 mm 22 mm 18,5 mm 18,5 mm 16,9 mm 18,5 mm 18,5 mm 16,9 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

18 Measuring and assembly of pleated blinds VS 4 Slope, VS 4 Slope S Measuring to Fit to indow eading - CA fixation d frame: 21 mm Order width Measure the width A at several points in case of possible frame size tolerances. Order dimensions* = A, and C (light dimensions) Controlling dimension = Straight frame: 21 mm Order width = = 5 Amm * The necessary reductions are determined by the manufacturer. Please specify if frames are angled. or straight. The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. assembly of pleated blinds VS 4 Slope S Pleated blinds VS 4 Slope S are equipped with a hinge located between the upper control rail and the slope rail. Assembly into the angled frame must be done by using a leveling wedge, because otherwise intermediate movable rail will protrude into space! ! alance wedge 11 CA11 (to frame, 1pc leveling wedge 11 ) CA22 (to frame, 2pc leveling wedge 11 = 22 ) CA33 (to frame, 3pc leveling wedge 11 = 33 ) CA44 (to frame, 4pc leveling wedge 11 = 44 ) Selecting the above value you receive a given number of leveling wedges under each clip. 18

19 PLEATED LINDS Assembly to frame (using wall bracket) - C fixation 5 mm 5 mm 5 mm = Desired Overlap Assembly to frame (using clamp bracket 25 mm) - V fixation The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. = Desired Overlap The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Distance etween lind and indow Pane = 5 mm 19! Please pay attention to window furniture. Order dimensions = A, and C including desired overlaps Controlling dimensions = including desired overlaps : Dimension = upper profile. Clip and bracket require another 4,5 mm each. Check if the clamping carrier can be used as regards window mechanism and the distance to the window sill (strength casement max. 25 mm). Please pay attention to window furniture. Order width = A including desired overlaps Order height 1 = height of window beadings at the highest point of order width minus 10 mm Order height 2 = height of window beading at the lowest point of order height C minus 10 mm Controlling dimension = ca. 10 mm Several linds Side by Side Light slit (fabric gap) between the blinds approx. 10 mm. Necessary rail distance is determined by the manufacturer. Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

20 asic Product Specification Pleated blind Type VS 5 1 Small width (1)* Overhang (k) eight 1 () eight 2 (C) min max min* max min max min max min min max 300 mm 1500 mm 70 mm 1450 mm 50 mm 1200 mm 300 mm 1500 mm 100 mm to width 1200 mm max mm *The minimum top width when using the loop cord is 80 mm. control Small width (1) Overhang (k) eight 1 () eight 2 (C) min max min* max min max min max min min max 300 mm 1500 mm mm 50 mm 1200 mm 300 mm 1500 mm 100 mm to width 1200 mm max mm Package eight lind eight Package eight 11,6 mm 22 mm Fitting Situation: Vertical : 1 + k always add width A! Clamping cors are fixed! 500 mm ca. 70 mm 1000 mm ca. 80 mm 1500 mm ca. 90 mm 2000 mm ca. 100 mm 18,5 mm 18,5 mm 16,9 mm 11,6 mm Typ plisse VS 5 SD 1 Small width (1)* Overhang (k) eight 1 () eight 2 (C) min max min* max min max min max min min max 300 mm 1000 mm 70 mm 950 mm 50 mm 930 mm 300 mm 2000 mm 100 mm *The minimum top width when using the loop cord is 80 mm. control Small width (1) Overhang (k) eight 1 () eight 2 (C) min max min* max min max min max min min max 300 mm 1000 mm mm 50 mm 880 mm 300 mm 2000 mm 100 mm Package eight lind eight Package eight 11,6 mm 22 mm Fitting Situation: Vertical : 1 + k always add width A! Clamping cors are fixed! 500 mm ca. 90 mm 1000 mm ca. 100 mm 1500 mm ca. 110 mm 2000 mm ca mm 18,5 mm 16,9 mm 18,5 mm 16,9 mm 11,6 mm 20

21 PLEATED LINDS Typ plisse VS 6 : 1 + k + 2k always add width A! Clamping cors are fixed! Also asymmetrically possible. Typ plisse VS 6 SD Fitting Situation: Vertical Fitting Situation: Vertical 1 : 1 + k + 2k always add width A! Clamping cors are fixed! Also asymmetrically possible. 1 control control Small width (1) Overhang (k/2k) eight 1 () eight 2 (C) min max min* max min max min max min min max 300 mm 1500 mm 70 mm 1400 mm 50 mm 1200 mm 300 mm 1500 mm 100 mm to width 1200 mm max mm *The minimum top width when using the loop cord is 80 mm. Small width (1) Overhang (k/2k) eight 1 () eight 2 (C) min max min* max min max min max min min max 300 mm 1500 mm mm 50 mm 1200 mm 300 mm 1500 mm 100 mm to width 1200 mm max mm Package eight lind eight Package eight 500 mm ca. 70 mm 1000 mm ca. 80 mm 1500 mm ca. 90 mm 2000 mm ca. 100 mm 21 Small width (1) Overhang (k/2k) eight 1 () eight 2 (C) min max min* max min max min max min min max 300 mm 1000 mm 70 mm 900 mm 50 mm 880 mm 300 mm 2000 mm 100 mm *The minimum top width when using the loop cord is 80 mm. Small width (1) Overhang (k/2k) eight 1 () eight 2 (C) min max min* max min max min max min min max 300 mm 1000 mm mm 50 mm 830 mm 300 mm 2000 mm 100 mm Package eight lind eight Package eight 500 mm ca. 90 mm 1000 mm ca. 100 mm 1500 mm ca. 110 mm 2000 mm ca mm 22 mm 22 mm 11,6 mm 18,5 mm 18,5 mm 16,9 mm 11,6 mm 18,5 mm 16,9 mm 18,5 mm 16,9 mm 11,6 mm 11,6 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

22 Measuring and assembly of pleated blinds VS 5, VS 5 SD, VS 6, VS 6 SD Measuring to Fit to indow eading - CA fixation 1 d frame: Measure the width A at several points in case of possible frame size tolerances. Use the smallest measured width. Straight frame: Minim. depth 21 mm Order width Minim. depth 21 mm Order width The slope can be left or right. It is measured in the horizontal plane. The area of overhang is determined as k = left or 2k = right from inside the room. Order dimension* = A, 1, k, 2k,, C (light dimensions) Controlling dimension = and 2 * The necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight. Assembly to frame (using wall bracket) - C fixation 1 Please pay attention to window furniture. = Desired Overlap The slope can be left or right. It is measured in the horizontal plane. The area of overhang is determined as k = left or 2k = right from inside the room. Order dimensions = A, 1, k, 2k,, C including desired overlaps Controlling dimensions = and 2 including desired overlaps Dimension = upper profile. Clip and bracket require another 4,5 mm each. Assembly to frame (using clamp bracket 25 mm) - V fixation 1! Check if the clamping carrier can be used as regards window mechanism and the distance to the window sill (strength casement max. 25 mm). Please pay attention to window furniture. = Desired Overlap The slope can be left or right. It is measured in the horizontal plane. The area of overhang is determined as k = left or 2k = right from inside the room. Order width = A, 1, k, 2k including desired overlaps Order height = minus 10 mm, C minus 5 mm Controlling dimension = and 2 22

23 PLEATED LINDS 5 mm 5 mm 5 mm Distance etween lind and indow Pane = 5 mm 1 1 The recess sizes are measured with a plumbline. 23 Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

24 asic Product Specification Pleated blind Type VS 7 1 Small width (1) Overhang (k/2k) eight () min max min* max min max min max min max 300 mm 1500 mm 70 mm 1400 mm 50 mm 1200 mm 300 mm 1500 mm to width 1200 mm max mm *The minimum top width when using the loop cord is 80 mm. Fitting Situation: Vertical : 1 + k + 2k always add width A! Clamping cors are fixed! Also asymmetrically possible. Pleated blind Type VS 8 1 control control Small width (1) Overhang (k/2k) eight () min max min max min max min max min max 300 mm 1500 mm mm 50 mm 1200 mm 300 mm 1500 mm to width 1200 mm max mm Package eight lind eight Package eight 500 mm ca. 70 mm 1000 mm ca. 80 mm 1500 mm ca. 90 mm 2000 mm ca. 100 mm Small width (1) Overhang (k/2k) eight () min max min* max min max min max min max 300 mm 1500 mm 70 mm 1450 mm 50 mm 1200 mm 300 mm 1500 mm to width 1200 mm max mm *The minimum top width when using the loop cord is 80 mm. Small width (1) Overhang (k/2k) eight () min max min max min max min max min max 300 mm 1500 mm mm 50 mm 1200 mm 300 mm 1500 mm to width 1200 mm max mm 11,6 mm Package eight lind eight Package eight Fitting Situation: Vertical : 1 + k + 2k always add width A! Clamping cors are fixed! 500 mm ca. 70 mm 1000 mm ca. 80 mm 1500 mm ca. 90 mm 2000 mm ca. 100 mm 11,6 mm 24

25 Pleated blind Type VS 9 : 1 + k + 2k always add width A! Clamping cors are fixed! Also asymmetrically possible. Pleated blind Type VS 9 D : k + 2k always add width A! Clamping cors are fixed! Also asymmetrically possible. Fitting Situation: Vertical Fitting Situation: Vertical control control Package eight lind eight 25 Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm PLEATED LINDS Small width (1) Overhang (k/2k) eight () min max min* min max min max min max 300 mm 1500 mm 70 mm 100 mm 1200 mm 300 mm 1500 mm to width 1200 mm max mm *The minimum top width when using the loop cord is 80 mm. Small width (1) Overhang (k/2k) eight () min max min min max min max min max 300 mm 1500 mm mm 1200 mm 300 mm 1500 mm to width 1200 mm max mm Package eight lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 22 mm 11,6 mm 18,5 mm 16,9 mm Small width (1) Overhang (k/2k) eight () min max min* min max min max min max 300 mm 1500 mm 70 mm 100 mm 1200 mm 300 mm 1500 mm to width 1200 mm max mm *The minimum top width when using the loop cord is 80 mm. Small width (1) Overhang (k/2k) eight () min max min min max min max min max 300 mm 1500 mm 100 mm 100 mm 1200 mm 300 mm 1500 mm to width 1200 mm max mm 22 mm 18,5 mm 16,9 mm 11,6 mm 11,6 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

26 Pleated blind Type VS 10 Upper width (1)* eight () min max min max min max 300 mm 1200 mm 70 mm 300 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. control Upper width (1) eight () min max min max min max 300 mm 1500 mm mm 1500 mm Package eight 11,6 mm Fitting Situation: Vertical : The slope can be left or right. Clamping cors are fixed! lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 22 mm 18,5 mm 16,9 mm 11,6 mm Pleated blind Type VS 10 D Upper width (1)* eight () min max min max min max 300 mm 1200 mm 70 mm 300 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. control Upper width (1) eight () min max min min max min max 300 mm 1500 mm 100 mm 300 mm 1500 mm mm Fitting Situation: Vertical : The slope can be left or right. Clamping cors are fixed! Package eight lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 18,5 mm 16,9 mm 11,6 mm 26

27 PLEATED LINDS Measuring and assembly of pleated blinds VS 7 a VS 8 Measuring to Fit to indow eading - CA fixation 1 1 Straight frame: Assembly to frame (using wall bracket) - C fixation d frame Minim. depth 21 mm Order width Minim. depth 21 mm Order width Measuring and assembly of pleated blinds VS 9, VS 9 D, VS 10, VS 10 SD Measuring to Fit to indow eading - CA fixation Assembly to frame (using wall bracket) - C fixation = Desired Overlap The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Straight frame = Desired Overlap The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. d frame Minim. depth 21 mm Order width Minim. depth 21 mm Order width The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. 27 Order dimension* = A, 1, k, 2k and (light dimensions) Controlling dimension = and 2 * The necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight. Please pay attention to window furniture. Order dimensions = A, 1, k, 2k and including desired overlaps Controlling dimensions = and 2 including desired overlaps Dimension = upper profile. Clip and bracket require another 4,5 mm each. Order dimension* = A, k, 2k and (light dimensions) Controlling dimension = and 2 * The necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight. Please pay attention to window furniture. Order dimensions = A, k, 2k and including desired overlaps Controlling dimensions = and 2 including desired overlaps Dimension = upper profile. Clip and bracket require another 4,5 mm each. Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

28 5 mm Distance etween lind and indow Pane = 5 mm 1 5 mm 5 mm 1. The recess sizes are measured with a plumb-line. Example of pleated blind VS 9 Example of pleated blind VS 9 D 28

29 PLEATED LINDS Freehanging pleated blinds F 29 Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

30 asic Product Specification Pleated blind Type F 1 eight () min max* min max 150 mm 2300 mm 300 mm 2600 mm *depending on fabric width eight () min max* min max 150 mm 2300 mm 300 mm 2600 mm *depending on fabric width Package eight lind eight Package eight 18,5 mm Fitting Situation: Vertical 500 mm ca. 50 mm 1000 mm ca. 60 mm 1500 mm ca. 70 mm 2000 mm ca. 80 mm 2600 mm ca. 90 mm - Optional with guide wire (extra charge). - Control possible left or right. 18,5 mm Pleated blind Type F 2 eight () min max min max 150 mm 2000 mm 300 mm 2600 mm *depending on fabric width plisse eight () min max* min max 150 mm 2000 mm 300 mm 2600 mm *depending on fabric width Package eight lind eight Package eight Fitting Situation: Vertical 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 2600 mm ca. 100 mm 18,5 mm 18,5 mm Optional with guide wire (extra charge). 18,5 mm 30

31 PLEATED LINDS Pleated blind Type F 3 Fitting Situation: Vertical Optional with guide wire (extra charge). Pleated blinds F3 always with 2 cord lock. In case of using two fabrics the order of substances is always set such that the fabric with heavier weight is always basic fabric placed in upper part of the blind, and the fabric with lower weight is always additional fabric places in lower part of the blind. eight () min max min max 150 mm 1500 mm 300 mm 2600 mm eight () min max min max 150 mm 1500 mm 300 mm 2600 mm Package eight lind eight Package eight 500 mm ca. 70 mm 1000 mm ca. 80 mm 1500 mm ca. 90 mm 2000 mm ca. 100 mm 2600 mm ca. 110 mm 31 18,5 mm 18,5 mm 18,5 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

32 Measuring and assembly of pleated blinds F 1, F 2, F 3 Assembly to frame (using wall bracket) - C fixation Please pay attention to window furniture. Order width = A including desired overlap Order height = including desired overlap : Dimension = upper profile. Clip and bracket require another 4,5 mm each. = Desired Overlap Assembly to frame (using clamp bracket 25 mm) - V fixation Check if the clamping carrier can be used! as regards window mechanism and the distance to the window sill (strength of window frame max. 25 mm). Please pay attention to window furniture. Order width = A including desired overlaps Order height = ith side guiding Order height = minus 10 mm = Desired Overlap Freehanging Order height = minus 5 mm Measuring to Fit to indow eading - CA fixation d frame: Minim. depth 21 mm Order width Measure the width A at several points in case of possible frame size tolerances. Order width = A Order height = Straight frame: Minim. depth 21 mm Order width = A minus 5 mm Order width = A minus 5 mm Order height = Attention: If Not Specified: Fabric = Rail End Caps Overlap! 5 mm 5 mm Distance etween lind and indow Pane = 5 mm 2,5 mm 5 mm! Specify assembly height! See notes about child safety o page 7. ca. 10 mm Several linds Side by Side Light slit (fabric gap) between the blinds approx. 10 mm. Necessary rail distance is determined by the manufacturer. 32

33 PLEATED LINDS asic Product Specification Pleated blind Type F Slope 1 Pleated blind Type F Slope 2 Fitting Situation: Vertical Fitting Situation: Vertical control ase width Slope width eight 1 () eight 2 (C) min max max min max max min max 300 mm 800 mm 1000 mm 300 mm 2600 mm 100 mm 5 35 Package eight lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 2600 mm ca. 100 mm Pleated blind is operable to the slope. Control is possible at higher or lower side (please specify if left or right). control Pleated blind is operable to the slope. Control on lower side is for bottom pleated blind, control on higher side is for upper pleated blind. - this type of pleated blinds is not deliver with honeycomb fabric 33 ase width Slope width eight 1 () eight 2 (C) min max max* min max max min max to angle to angle to angle to angle mm 2200 mm1900 mm1600 mm1100 mm2300 mm 300 mm 2600 mm 100 mm 5 50 * depending on fabric width ase width Slope eight 1 eight 2 width () (C) min max max* min max max min max to angle 15 to angle 30 to angle mm 2200 mm 1900 mm 1700 mm 2200 mm 300 mm 2600 mm 100 mm 5 40 * depending on fabric width Package eight lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 2600 mm ca. 100 mm 18,5 mm 18,5 mm 18,5 mm 18,5 mm 18,5 mm 18,5 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

34 Measuring and assembly of pleated blinds F Slope 1, F Slope 2 Measuring to Fit to indow eading - CA fixation d frame Straight frame Minim. depth 21 mm Order width Minim. depth 21 mm Order width The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Measure the width A at several points in case of possible frame size tolerances. Order dimension* = A, and C (light dimensions) Controlling dimension = * The necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight. No side guidance is possible. for assembly of pleated blinds F Slope 2 Pleated blinds F Slope 2 are equipped with the hinge located between upper control and profile in the slope. The assembly to the angled frame must necessarily be done with leveling wedges, otherwise the moving of middle profile is not correct! 90 alance wedge 11 CA11 (to frame, 1pc leveling wedge 11 ) CA22 (to frame, 2pc leveling wedge 11 = 22 ) CA33 (to frame, 3pc leveling wedge 11 = 33 ) CA44 (to frame, 4pc leveling wedge 11 = 44 ) Selecting the above value you receive a given number of leveling wedge under each clip. Assembly to frame (using wall bracket) - C fixation Please pay attention to window furniture. Order dimensions = A, and C including desired overlaps Checking dimension = including desired overlaps Dimension = upper profile. Clip and bracket require another 4,5 mm each. No side guidance is possible. = Desired Overlap The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. 34

35 PLEATED LINDS Assembly to frame (using clamp bracket 25 mm) - V fixation for assembly of pleated blinds F Slope 2 The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. 5 mm 5 mm 5 mm Distance etween lind and indow Pane = 5 mm ca. 10 mm Several linds Side by Side Light slit (fabric gap) between the blinds approx. 10 mm. Necessary rail distance is determined by the manufacturer. = Desired Overlap Ratio width of the fabric to pleated blind width mm mm F Slope F Slope ! Check if the clamping carrier can be used as regards window mechanism and the distance to the window sill (strength of window frame max. 25 mm). Please pay attention to window furniture. Order dimension = A, and C including desired overlaps Controlling dimension = No side guidance is possible. The steeper the angle, the less the width. The angle of the slope has a considerable influence on the maximum width. The diagram shows the possible width in relation to angle and width of the fabric on. The height of the slope is calculated minus C. Specify assembly height! See notes about child safety o page Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

36 asic Product Specification Pleated blind Type FD Slope 3 control ase width Slope width eight () min max* max min max min max 300 mm 2200 mm 2300 mm 300 mm 1600 mm 5 50 * depending on fabric width ase width Slope width eight () min max* max min max min max 300 mm 2200 mm 2300 mm 300 mm 1600 mm 5 40 * depending on fabric width Fitting Situation: Vertical Package eight lind eight Package eight 18,5 mm : Pleated blind is operable to the slope. Control is possible at higher or lower side (please specify if left or right). 500 mm ca. 70 mm 1000 mm ca. 80 mm 1500 mm ca. 90 mm 18,5 mm 36

37 PLEATED LINDS Measuring and assembly of pleated blinds FD Slope 3 Measuring to Fit to indow eading - CA fixation d frame Minim. depth 21 mm Order width Straight frame Minim. depth 21 mm Order width : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Assembly to frame (using wall bracket) - C fixation Distance etween lind and indow Pane = 5 mm = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. 5 mm 5 mm 5 mm Ratio width of the fabric to pleated blind width mm mm FD Slope The steeper the angle, the less the width. The angle of the slope has a considerable influence on the maximum width. The diagram shows the possible width in relation to angle and width of the fabric on. The height of the slope is calculated minus C ! Order dimension* = A and (light dimensions) Controlling dimension = * Necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight. Please pay attention to window furniture. Order dimension* = A and (light dimensions) Controlling dimension = Dimension = upper profile. Clip and bracket require another 4,5 mm each. No side guidance is possible. Due to the profile location in the corner, there are areas which are not shaded! Specify assembly height! See notes about child safety o page 7. Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

38 asic Product Specification Pleated blind Type F7 1 Small width (1) Overhang (k/2k) eight () min max min max min max min max 600 mm 2000 mm 500 mm 1900 mm 50 mm 200 mm 300 mm 2400 mm control Small width (1) Overhang (k/2k) eight () min max min max min max min max 600 mm 2000 mm 500 mm 1900 mm 50 mm 200 mm 300 mm 2400 mm Package eight Fitting Situation: Vertical : 1 + k + 2k always add width A! Also asymmetrically possible. Control possible left or right (please specify). Control cord in the viewing area. lind eight Package eight 500 mm ca. 50 mm 1000 mm ca. 60 mm 1500 mm ca. 70 mm 2000 mm ca. 80 mm 2400 mm ca. 90 mm 18,5 mm 18,5 mm 18,5 mm Pleated blind Type F 8 1 Small width (1) Overhang (k) eight () min max min max min max min max 550 mm 2000 mm 500 mm 1950 mm 50 mm 200 mm 300 mm 2400 mm control Small width (1) Overhang (k) eight () min max min max min max min max 550 mm 2000 mm 500 mm 1900 mm 50 mm 200 mm 300 mm 2400 mm Package eight Fitting Situation: Vertical : 1 + k always add width A! Control possible left or right (please specify). Control cord in the viewing area. lind eight Package eight 500 mm ca. 50 mm 1000 mm ca. 60 mm 1500 mm ca. 70 mm 2000 mm ca. 80 mm 2400 mm ca. 90 mm 18,5 mm 18,5 mm 18,5 mm 38

39 PLEATED LINDS Measuring and assembly of pleated blinds F 7 a F 8 Measuring to Fit to indow eading - CA fixation Assembly to frame (using clamp bracket 25 mm) - V fixation d frame Minim. depth 21 mm Order width Straight frame Minim. depth 21 mm Order width : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Assembly to frame (using wall bracket) - C fixation = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. 39! Order dimension* = A, 1, k, 2k and (light dimension) Controlling dimension = and 2 * Necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight. Please pay attention to window furniture. Order dimension = A, 1, k, 2k and including desired overlaps Controlling dimension = and 2 including desired overlaps Dimension = upper profile. Clip and bracket require another 4,5 mm each. Check if the clamping carrier can be used as regards window mechanism and the distance to the window sill (strength of window frame max. 25 mm). Please pay attention to window furniture. Order width = A, 1, k including desired overlaps Order height = minus 10 mm Controlling dimension = (2) Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

40 5 mm Distance etween lind and indow Pane = 5 mm 1 5 mm 5 mm! Specify assembly height! See notes about child safety o page 7. 1 The recess sizes are measured with a plumb-line. 40

41 PLEATED LINDS Roof pleated blinds DFC 41 Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

42 asic Product Specification Pleated blind Type DFC 10 eight () min max min max 250 mm 1500 mm 400 mm 1500 mm to width 1200 mm max mm control eight () min max min max 250 mm 1500 mm 400 mm 1500 mm to width 1200 mm max mm Package eight 34,5 mm lind eight Package eight 36,5 mm Fitting Situations: d 500 mm ca. 70 mm 1000 mm ca. 80 mm 1500 mm ca. 90 mm 31,2 mm Possible with operating rod. For windows with angled or straight frames. DFC only available for assembly in the beading. 27 mm 23,5 mm 32,2 mm Pleated blind Type DFC 20 eight () min max min max 250 mm 1500 mm 400 mm 1500 mm to width 1200 mm max mm control eight () min max min max 250 mm 1500 mm 400 mm 1500 mm to width 1200 mm max mm Package eight 27 mm Fitting Situations: d Possible with operating rod. For windows with angled or straight frames. DFC only available for assembly in the beading. lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 23,5 mm 23,5 mm 32,2 mm 31,2 mm 27 mm 42

43 PLEATED LINDS Pleated blind Type DFC 30 Fitting Situations: d control Possible with operating rod. For windows with angled or straight frames. DFC only available for assembly in the beading. In case of using two fabrics the order of substances is always set such that the fabric with heavier weight is always basic fabric placed in upper part of the blind, and the fabric with lower weight is always additional fabric places in lower part of the blind. eight () min max min max 250 mm 1500 mm 400 mm 1500 mm to width 1200 mm max mm eight () min max min max 250 mm 1500 mm 400 mm 1500 mm to width 1200 mm max mm Package eight lind eight Package eight 500 mm ca. 100 mm 1000 mm ca mm ca. 140 mm 43 34,5 mm 27,5 mm 27 mm 36,5 mm 23,5 mm 29 mm 32,2 mm 31,2 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

44 Measuring and assembly of pleated blinds DFC Standardised roof windows roof windows Velux Type window A 96 Type window 100 light window size light window size Assembly of pleated blinds si always done to the frame. Over the years Velux changed several types of windows, without issuing new label types. Please specify: - window brand - type (e.g. GGL) - dimensions (e.g. FK06) In addition to this, please provide a light window dimensions as the checking dimensions, measured at the front edge (see drawing). Attention: type DFC can not be assembled to windows GGL produced in June roof windows Roto Old design 90 New design 100 light window size light window size Assembly of pleated blinds si always done to the frame. Company Roto produces 2 types of window frames. Please specify: - window brand - type (e.g. R7) - dimensions (e.g. 7/11) In addition to this, please provide a light window dimensions as the checking dimensions. Please note that the light dimensions are measured at the narrowest point for Roto windows (see drawing). roof windows raas/lefa/dörken Straight frame 90 Attention: Pleated blinds DFC with handle can not be assembled to roof windows produced by these companies. light window size roof windows Fakro Non-Standardised roof windows d frame 10 light window size Assembly of pleated blinds si always done to the frame. Please specify: - window brand - type (e.g. FTS) - dimensions (e.g. 66/98) In addition to this, please provide a light window dimensions as the checking dimensions. Straight frame 90 d frame Min. depth 33 mm light window size Min. depth 33 mm light window size Assembly of pleated blinds si always done to the frame. Please specify the light dimensions of window measured at the front edge (see drawing). In addition to this, please specify bevel frame, bevel angle between window pane and window frame. 44 Measure at several points in case of possible frame size tolerances.

45 PLEATED LINDS Pleated blinds for conservatories PL 45 Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

46 asic Product Specification Pleated blind Type PL 11 eight () min max min max 200 mm 1500 mm 300 mm 4000 mm eight () min max min max 200 mm 1500 mm 300 mm 4000 mm Package eight Fitting Situations: d / orizontal Possible with operating rod (extra charge). Assembly angled or horizontal. Tension wires are UV-resistant and made of black coated steel wire. lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 2500 mm ca. 100 mm 3000 mm ca. 110 mm 3500 mm ca mm ca. 130 mm 22 mm 18,5 mm 16,9 mm 18,5 mm 46

47 PLEATED LINDS Measuring and assembly of pleated blinds PL 11 Assembly to rafters - CA fixation (assembly to window beading) Anlagenhöhe Please consider the air ventilation gaps at the top and bottom. 100 Minimum depth 100 mm Pleated blind Order width=a-5mm Assembly under rafters - C fixation (assembly to frame using wall bracket) lind height Minimum depth 100 mm Pleated blind recess size = Desired Overlap for assembly using bracket Dimension = upper profile. Clip and bracket require another 4,5 mm each. 50 A 47!! For installation between the rafters, please measure the width A in several places and subtract 5mm from the narrowest measure. Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght (). Order width = A minus 5 mm Order height = minus ventilation gaps and mounting profile if it should be used. For installation between the rafters, please measure their distance and add the favoured Overlap. Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght (). Order width = recess size = A plus desired overlaps Order height = r ecess size = minus ventilation gaps and mounting profile if it should be used. Air Circulation Pleated blinds in conservatories are an ideal, functional sun protection. This requires adequate ventilation and air circulation. Insufficient ventilation and air circulation can cause condensation. No warranty for material damage caused by dripping condensation water and sharp glass cleaner, which encounter directly or indirectly with the fabric. Also no warranty for insect excrements. Assembly spaces Please leave a minimum space of 100 mm between the Cosiflor pleated blind and the window pane and at least 50 mm at the top and bottom between the mounting profile and the wall to ensure sufficent circulation. Displayed mounting profile is not part of delivered pleated blinds. Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

48 A A A Always measure indoors. The amount of tensioned wires (black) lind width Tensioned wired amount 200 mm mm mm mm mm mm mm mm mm mm mm mm mm mm 7 2,5 mm Attention: If Not Specified: Fabric = Rail End Caps Overlap! Please : No warranty on glass damages that occur after the installation of pleated blinds. 48

49 PLEATED LINDS asic Product Specification Pleated blind Type PL k + 2k always add width A! Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. Also asymmetrically possible. Pleated blind Type PL k always add width A! Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. 1 Fitting Situations: d / orizontal Fitting Situations: d / orizontal 1 control control Small width (1) Overhang (k/2k) eight () min max min* max min max min max min max 300 mm 1500 mm 70 mm 1400 mm 50 mm 1200 mm 300 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. Small width (1) Overhang (k/2k) eight () min max min max min max min max min max 300 mm 1500 mm mm 50 mm 1000 mm 300 mm 2000 mm Package eight lind eight 49 Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm Package eight lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 22 mm Small width (1) Overhang (k/2k) eight () min max min* max min max min max min max 300 mm 1500 mm 70 mm 1450 mm 50 mm 1200 mm 300 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. Small width (1) Overhang (k/2k) eight () min max min max min max min max min max 300 mm 1500 mm mm 50 mm 1000 mm 300 mm 2000 mm mm 11,6 mm 18,5 mm 16,9 mm 11,6 mm 18,5 mm 16,9 mm 11,6 mm 11,6 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

50 Pleated blind Type PL 32 Upper width (1)* Overhang (k/2k) eight () min max min max min max min max 300 mm 1500 mm 70 mm 100 mm 1200 mm 300 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. Upper width (1) Overhang (k/2k) eight () min max min max min max min max 300 mm 1500 mm mm 1000 mm 300 mm 2000 mm control Package eight lind eight Package eight 11,6 mm 22 mm k + 2k always add width A! Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. Also asymmetrically possible. Fitting Situations: d / orizontal 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 18,5 mm 16,9 mm 11,6 Pleated blind Type PL 32 D Upper width (1)* Overhang (k/2k) eight () min max min max min max min max 300 mm 1500 mm 70 mm 100 mm 1200 mm 300 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. Upper width (1) Overhang (k/2k) eight () min max min max min max min max 300 mm 1500 mm mm 1000 mm 300 mm 2000 mm control Package eight lind eight Package eight 22 mm k + 2k always add width A! Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. Also asymmetrically possible. Fitting Situations: d / orizontal 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 18,5 mm 16,9 mm 11,6 mm 50

51 PLEATED LINDS Pleated blind Type PL 33 Fitting Situations: d / orizontal control Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. Pleated blind Type PL 33D Fitting Situations: d / orizontal control Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. Upper width (1)* eight () min max min max min max 300 mm 1200 mm 70 mm 300 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. Upper width (1) eight () min max min max min max 300 mm 1200 mm mm 2000 mm Package eight lind eight 51 Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm Package eight lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 22 mm 11,6 mm 18,5 mm 16,9 mm Upper width (1)* eight () min max min max min max 300 mm 1200 mm 70 mm 300 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. Upper width (1) eight () min max min max min max 300 mm 1200 mm mm 2000 mm mm 18,5 mm 16,9 mm 11,6 mm 11,6 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

52 Measuring and assembly of pleated blinds PL 30 a PL 31 Assembly to rafters - CA fixation (assembly to window beading) 1 Minimum depth 100 mm Pleated blind : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. A! Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght (). Order width* = A, 1, k and 2k (light dimensions) Order height = minus ventilation gaps and mounting profile if it should be used. Controlling dimension = and 2 *The necessary reductions are determined by the manufacturer. Assembly under rafters - C fixation (assembly to frame using wall bracket) 1 Minimum depth 100 mm Pleated blind A Recess size = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Please consider the air ventilation gaps at! the top and bottom as well as the thickness of mounting profile for the lenght (). Please pay attention to window furniture. Order width* = A, 1, k and 2k including desired overlaps Order height = minus ventilation gaps and mounting profile if it should be used (eventually consider desired overlaps ). Controlling dimension = and 2 including desired overlaps for assembly using bracket: Dimension = upper profile. Clip and bracket require another 4,5 mm each. Measuring and assembly of pleated blinds PL 32, PL 32 D, PL 33, PL 33 D Assembly to rafters - CA fixation (assembly to window beading)! Minimum depth 100 mm Pleated blind : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. A Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght (). Order width* = A, k and 2k (light dimensions) Order height = minus ventilation gaps and mounting profile if it should be used. Controlling dimension = and 2 * The necessary reductions are determined by the manufacturer. 52

53 PLEATED LINDS Assembly under rafters - C fixation (assembly to frame using wall bracket) Please consider the air ventilation gaps at the top and bottom. Please always measure indoors. Distance of tensioned wire is max. 250 mm! Minimum depth 100 mm Pleated blind A Recess size = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form.! lind eight height Anlagenhöhe Due to the profile location in the corner, there are areas which are not shaded! These areas are not reaseon for complaint ! Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght (). Please pay attention to window furniture. Order width* = A, k and 2k including desired overlaps Order height = minus ventilation gaps and mounting profile if it should be used (eventually consider desired overlaps ). Controlling dimension = and 2 including desired overlaps for assembly using bracket: Dimension = upper profile. Clip and bracket require another 4,5 mm each. Air Circulation Pleated blinds in conservatories are an ideal, functional sun protection. This requires adequate ventilation and air circulation. Insufficient ventilation and air circulation can cause condensation. No warranty for material damage caused by dripping condensation water and sharp glass cleaner, which encounter directly or indirectly with the fabric. Also no warranty for insect excrements. Assembly spaces Please leave a minimum space of 100 mm between the Cosiflor pleated blind and the window pane and at least 50 mm at the top and bottom between the mounting profile and the wall to ensure sufficent circulation. Displayed mounting profile is not part of delivered pleated blinds. Please : No warranty on glass damages that occur after the installation of pleated blinds. Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

54 asic Product Specification Pleated blind Type PL 40 Slope width eight 1 () eight 2 (C) min max max do 45 do 60 max* min max min max min max 300 mm 1500 mm 1100 mm 2300 mm 300 mm 4000 mm 100 mm 2000 mm 5 60 * depending on fabric width - this type of pleated blinds is not deliver with honeycomb fabric Package eight Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. Also asymmetrically possible. Fitting Situations: d / orizontal control lind eight Package eight 500 mm ca. 60 mm 1000 mm ca. 70 mm 1500 mm ca. 80 mm 2000 mm ca. 90 mm 2500 mm ca. 100 mm 3000 mm ca. 110 mm 3500 mm ca mm ca. 130 mm 22 mm 18,5 mm 18,5 mm 16,9 mm 18,5 mm 54

55 PLEATED LINDS Measuring and assembly of pleated blinds PL 40 Assembly to rafters - CA fixation (assembly to window beading) Assembly under rafters - C fixation (assembly to frame using wall bracket) Minimum depth 100 mm Pleated blind : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. A Minimum depth 100 mm Pleated blind A Recess size = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form lind eight Anlagenhöhe Please consider the air ventilation gaps at the top and bottom. Please always measure indoors. Distance of tensioned wire is max. 250 mm! ! Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght (). Order width* = A (light dimensions) Order height 1 = minus ventilation gaps and mounting profile if it should be used. Order height 2 = C minus ventilation gaps and mounting profile. Controlling dimension = *The necessary reductions are determined by the manufacturer.! Please consider the air ventilation gaps at the top and bottom as well as thethickness of mounting profile for the lenght (). Please pay attention to window furniture. Order width = A including desired overlaps Order height 1 = minus ventilation gaps and mounting profile if it should be used (eventually consider desired overlaps ). Order height 2 = C minus ventilation gaps and mounting profile if it should be used (eventually consider desired overlaps ). Controlling dimension = including desired overlaps for assembly using bracket: Dimension = upper profile. Clip and bracket require another 4,5 mm each. Air Circulation Pleated blinds in conservatories are an ideal, functional sun protection. This requires adequate ventilation and air circulation. Insufficient ventilation and air circulation can cause condensation. No warranty for material damage caused by dripping condensation water and sharp glass cleaner, which encounter directly or indirectly with the fabric. Also no warranty for insect excrements. Assembly spaces Please leave a minimum space of 100 mm between the Cosiflor pleated blind and the window pane and at least 50 mm at the top and bottom between the mounting profile and the wall to ensure sufficent circulation. Displayed mounting profile is not part of delivered pleated blinds. Please : No warranty on glass damages that occur after the installation of pleated blinds. Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

56 asic Product Specification Pleated blind Type PL 41 1 Small width Overhang eight 1 eight 2eight 3 (1) (k/2k) () (C) (-C) min max min* max min max min max min max min max 300 mm 1500 mm 70 mm 1450 mm 50 mm 1200 mm 300 mm 4000 mm 100 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. control Small width Overhang eight 1 eight 2eight 3 (1) (k/2k) () (C) (-C) min max min max min max min max min max min max 300 mm 1500 mm mm 50 mm 1000 mm 300 mm 4000 mm 100 mm 2000 mm Package eight lind eight Package eight 11,6 mm 22 mm : 1 + k always add width A! Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. Fitting Situations: d / orizontal 500 mm ca. 80 mm 1000 mm ca.90 mm 1500 mm ca. 100 mm 2000 mm ca. 110 mm 18,5 mm 18,5 mm 16,9 mm 11,6 mm Pleated blind Type PL 42 1 control Small width Overhang eight 1 eight 2eight 3 (1) (k/2k) () (C) (-C) min max min* max min max min max min max min max 300 mm 1500 mm 70 mm 1450 mm 50 mm 1200 mm 300 mm 4000 mm 100 mm 2000 mm *The minimum top width when using the loop cord is 80 mm. Small width Overhang eight 1 eight 2 eight 3 (1) (k/2k) () (C) (-C) min max min max min max min max min max min max 300 mm 1500 mm mm 50 mm 1000 mm 300 mm 4000 mm 100 mm 2000 mm Package eight lind eight Package eight 22 mm 11,6 mm Fitting Situations: d / orizontal : 1 + k + 2k always add width A! Tension ires are UV-resistant and made of black coated steel wire. Operating rod is possible. Also asymmetrically possible. 500 mm ca. 80 mm 1000 mm ca.90 mm 1500 mm ca. 100 mm 2000 mm ca. 110 mm 18,5 mm 18,5 mm 16,9 mm 11,6 mm 56

57 PLEATED LINDS Measuring and assembly of pleated blinds PL 41 Assembly to rafters - CA fixation (assembly to window beading) 1 1 Minimum depth 100 mm Pleated blind The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Assembly under rafters - C fixation (assembly to frame using wall bracket) A Minimum depth 100 mm Pleated blind A Recess size = Desired Overlap The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. 57! Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght (). Order width* = A, 1, k and 2k (light dimensions) Order height 1 = minus ventilation gaps and mounting profile if it should be used. Order height 2 = C minus ventilation gaps and mounting profile. Controlling dimension = * The necessary reductions are determined by the manufacturer. Please consider the air ventilation gaps at the top! and bottom as well as the thickness of mounting profile for the lenght (). Please pay attention to window furniture. Order width = A, 1, k and 2k including desired overlaps Order height 1 = minus ventilation gaps and mounting profile if it should be used (eventually consider desired overlaps ). Order height 2 = C minus ventilation gaps and mounting profile if it should be used (eventually consider desired overlaps ). Controlling dimension = including desired overlaps for assembly using bracket: Dimension = upper profile. Clip and bracket require another 4,5 mm each. Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

58 Measuring and assembly of pleated blinds PL 42 Assembly to rafters - CA fixation (assembly to window beading) 1 Minimum depth 100 mm Pleated blind : The slope can be left or right. It is measured in the horizontal plane. The area of overhang is determined as k = left or 2k = right from inside the room. A! Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght ( and C). Order width* = A, 1, k and 2k (light dimensions) Order height 1 = minus ventilation gaps and mounting profile if it should be used. Order height 2 = C minus ventilation gaps and mounting profile. Controlling dimension = * The necessary reductions are determined by the manufacturer. Assembly under rafters - C fixation (assembly to frame using wall bracket) 1 Minimum depth 100 mm Pleated blind Recess size = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. The area of overhang is determined as k = left or 2k = right from inside the room. A! Please consider the air ventilation gaps at the top and bottom as well as the thickness of mounting profile for the lenght (). Please pay attention to window furniture. Order width = A, 1, k and 2k including desired overlaps Order height 1 = minus ventilation gaps and mounting profile if it should be used (eventually consider desired overlaps ). Order height 2 = C minus ventilation gaps and mounting profile if it should be used (eventually consider desired overlaps ). Controlling dimension = including desired overlaps for assembly using bracket: Dimension = upper profile. Clip and bracket require another 4,5 mm each lind eight Anlagenhöhe 50 Air Circulation Pleated blinds in conservatories are an ideal, functional sun protection. This requires adequate ventilation and air circulation. Insufficient ventilation and air circulation can cause condensation. No warranty for material damage caused by dripping condensation water and sharp glass cleaner, which encounter directly or indirectly with the fabric. Also no warranty for insect excrements. Assembly spaces Please leave a minimum space of 100 mm between the Cosiflor pleated blind and the window pane and at least 50 mm at the top and bottom between the mounting profile and the wall to ensure sufficent circulation. Displayed mounting profile is not part of delivered pleated blinds. Please consider the air ventilation gaps at the top and bottom. Please always measure indoors. Distance of tensioned wire is max. 250 mm! Please : No warranty on glass damages that occur after the installation of pleated blinds. 58

59 PLEATED LINDS Pleated blinds shapes SD and SR 59 Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

60 asic Product Specification Pleated SD 2 blind Type SD 2 Dreieck feststehend eight () min max* min max 200 mm 1600 mm 200 mm 1600 mm *depending on fabric width Limit dimensions of honeycomb pleated blinds 11,6 mm - this type of pleated blinds is not deliver with honeycomb fabric 11,6 mm Fitting Situation: Vertical Pleated blind Type SD 3 Slope width eight () min max max* min max 200 mm 2000 mm 2300 mm 200 mm 2000 mm *depending on fabric width Limit dimensions of honeycomb pleated blinds - this type of pleated blinds is not deliver with honeycomb fabric 11,6 mm 11,6 mm Fitting Situation: Vertical 60

61 PLEATED LINDS Measuring and assembly of pleated blinds SD 2 Assembly to window beading - CA fixation Assembly to frame (using wall bracket) - C fixation A d frame Minimum depth 21 mm Order width Straight frame Minimum depth 21 mm Order width : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Measuring and assembly of pleated blinds SD 3 Assembly to window beading - CA fixation d frame 61 = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Minimum depth 21 mm Order width Straight frame Minimum depth 21 mm Order width : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form. Assembly to frame (using wall bracket) - C fixation = Desired Overlap : The slope can be left or right. It is measured in the horizontal plane. Orientation of the slope is determined by the height left or right in the order form.!! Pleated blinds for conservatories Minimum distance to window pane is 100 mm. Order dimension* = A and (light dimensions) Controlling dimension = *The necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight. Please pay attention to window furniture. Order dimension = and including desired overlaps Controlling dimensions = including desired overlaps : Dimension = upper profile. Clip and bracket require another 4,5 mm each. Pleated blinds for conservatories Minimum distance to window pane is 100 mm. Order dimension* = A and (light dimensions) *The necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight. Please pay attention to window furniture. Order dimensions = A and including desired overlaps : Dimension = upper profile. Clip and bracket require another 4,5 mm each. Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

62 5 mm Distance etween lind and indow Pane = 5 mm Due to the profile location in the corner, there are areas which are not shaded! 5 mm 5 mm Attention Pleated blinds for conservatories - distance between blind and window pane = 5 mm Example of pleated blind SD 2 62

63 PLEATED LINDS asic Product Specification Pleated blind Type SR 1 S Fitting Situation: Vertical. Due to the curvature and the diagonal lead cord, the ends of the hinge bulge simultaneously that pleated blinds are pushed upwards. This is a technicalreasons and did not justify the complaint. control Upper rail width (1) eight () min max min max 300 mm 1500 mm cca 80 mm 300 mm 1500 mm Upper rail width (1) eight () min max min max 300 mm 1200 mm cca 80 mm 300 mm 1200 mm Package eight lind eight Package eight 500 mm ca. 50 mm 1000 mm ca. 60 mm 1500 mm ca. 70 mm mm 11,6 mm 18,5 mm 16,9 mm Pleated blinds shapes SD and SR Pleated blinds for conservatories PL Roof pleated blinds DFC Freehanging pleted blinds F Pre-tensioned pleated blinds VS

64 Measuring and assembly of pleated blinds SR 1 S Assembly to window beading - CA fixation d frame Minimum depth 21 mm Order width Straight frame Minimum depth 21 mm Order width Order dimension* = A and (light dimensions) *The necessary reductions are determined by the manufacturer. Please specify if frames are angled or straight.! For round blinds, please supply a template on scale of 1:1. Assembly to frame (using wall bracket) - C fixation Please pay attention to window furniture. Order dimensions = A and including desired overlaps : Dimension = upper profile. Clip and bracket require another 4,5 mm each. A = Desired Overlap! hen ordering these blinds, please supply a dimension drawing with all required blind sizes. For round blinds, please supply a template on scale of 1:1. 5 mm Distance between blind and window pane = 5 mm 5 mm 5 mm Given that the profile is located in the arc will generate surfaces which are not obscured. These surfaces are not a reason for complaint. 64

65 PLEATED LINDS : 65

66 :

67

68 ISOTRA a.s. ílovecká 2411/1, Opava Czech Republic ISOTRA Partner Tel.: Fax: Released: 03/2017