Pebbletex Adhered Mat Design. Typical Details
|
|
- Bennett Jacobs
- 5 years ago
- Views:
Transcription
1 Pebbletex Adhered Mat Design Typical Details
2 (THIS PAGE INTENTIONALLY LEFT BLANK)
3 Pebbletex Adhered Mat Design TABLE OF CONTENTS 1. Pebbletex Adhered Mat Design Application (Plan VIew) 2. Pebbletex Adhered Mat Design (Isometric View) 3. Aesthetic Groove 4. Insulation Boards/Reinforcing Mesh Application at Openings 5. Window Head (Flush) 6. Window Head (Recessed) 7. Window Jamb Detail (Flush) 8. Window Jamb Detail (Recessed) 9. Window Sill Detail (Flush) 10. Window Sill Detail (Recessed) 11. Roof Edge Flashing Detail 12. Metal Coping Detail 13. Parapet Cap Detail 14. Expansion Joint Detail at Floorline 15. Expansion Joint at Change in Substrate 16. Section at Fascia/Soffit 17. Expansion Joint Detail 18. Pipe Penetration 19. Corner Mesh Application with STRONG 15 or HI-IMPACT 20 (Plan View) 20. Corner Mesh Application with Standard Mesh, INTERMEDIATE 6 or 12 (Plan View) 21. Light Fixture 22. Termination at Foundation 23. Termination at Foundation (Flush) 24. Kick-out Flashing Detail
4 Pebbletex Adhered Mat Design FINESTOP, FINESTOP RA OR FINESTONE REINFORCING MESH AM-01 TYPICAL PEBBLETEX ADHERED MAT DESIGN APPLICATION (PLAN VIEW) FINESTOP, FINESTOP RA OR SECOND- ARY MOISTURE SELF-ADHERING MESH TAPE (4 ), 4 SHEATHING FABRIC OR FINESTONE FINISH COAT FINESTONE REINFORCING MESH AM-02 TYPICAL PEBBLETEX ADHERED MAT DESIGN (ISOMETRIC VIEW)
5 ACCEPTABLE SHEATHING MECHANICAL FASTENER FINESTOP, FINESTOP RA OR AESTHETIC GROOVE FINESTONE INSULATION BOARD FINESTONE REINFORCING MESH MIN. 19 mm (3/4 ) AM-03 TYPICAL AESTHETIC GROOVE (PLAN VIEW) STAGGER INSULATION BOARD JOINTS AT CORNER OF OPENINGS WRAP AND STANDARD MESH REINFORCING MESH AT INSULATION BOARD EDGES STANDARD MESH REINFORCING MESH EMBEDDED IN 229 mm (9 ) TYPICAL AT WINDOWS, DOORS, ETC. MAINTAIN A MIN. 13 mm (1/2 ) PERIMETER SEALANT JOINT FLASHINGS ARE BY OTHERS AND SHALL BE AS PER DESIGN/CODE REQUIREMENTS 305 mm (12 ) AM-04 TYPICAL INSULATION BOARDS/REINFORCING MESH APPLICATION AT OPENINGS
6 Pebbletex Adhered Mat Design FINESTOP, FINESTOP RA OR SELF-ADHERING MESH TAPE (4 ), 4 SHEATHING FABRIC OR FLASHING W/ SEALANT WINDOW IF IS USED IN LIEU OF FINESTOP OR FINESTOP RA, ENSURE BARRIER IS PROPERLY LAPPED OVER THE FLASHING FLANGE. AM-05 TYPICAL WINDOW HEAD (FLUSH) FINESTOP, FINESTOP RA OR PROTECTION BARRIER FINESTONE REINFORCING MESH BASF COLOR COAT WINDOW AM-06 TYPICAL WINDOW HEAD (RECESSED)
7 FINESTOP OR FINESTOP RA WS FLASH ALTERNATE OPENING PROTECTION OPTION FOR WINDOW JAMBS (WS FLASH MAY BE APPLIED UNDER OR OVER THE FINESTOP OR FINESTOP RA). FINESTOP FINESTOP RA OR SELF-ADHERING MESH TAPE (9 ) EMBEDDED IN FINESTOP OR 9 SHEATHING FABRIC EMBEDDED IN FINESTOP RA BASF COLOR COAT WINDOW SEE ALTERNATE OPTION DETAIL AM-07 TYPICAL WINDOW JAMB DETAIL (FLUSH) FINESTOP OR FINESTOP RA ALTERNATE OPENING PROTECTION OPTION FOR WINDOW JAMBS (WS FLASH MAY BE APPLIED UNDER OR OVER THE FINESTOP OR FINESTOP RA). FINESTOP, FINESTOP RA OR SELF-ADHERING MESH TAPE (9 ) EMBEDDED IN FINESTOP OR 9 SHEATHING FABRIC EMBEDDED IN FINESTOP RA BASF COLOR COAT WINDOW AM-08 TYPICAL WINDOW JAMB DETAIL (RECESSED)
8 Pebbletex Adhered Mat Design WINDOW FINESTONE ASAP SELF-ADHERING MESH TAPE (9 ) EMBEDDED IN FINESTOP OR 9 SHEATHING FABRIC EMBEDDED IN FINESTOP RA FINESTOP, FINESTOP RA OR AM-09 TYPICAL SILL DETAIL (FLUSH) SEE ALTERNATE OPTION DETAIL FINESTOP OR FINESTOP RA ALTERNATE OPENING PROTECTION OPTION FOR WINDOW SILL (WS FLASH MAY BE APPLIED UNDER OR OVER THE FINESTOP OR FINESTOP RA). WINDOW PAN FLASHING SELF-ADHERING MESH TAPE (9 ) EMBEDDED IN FINESTOP OR 9 SHEATHING FABRIC EMBEDDED IN FINESTOP RA SEALANT FINESTOP, FINESTOP RA OR AM-10 TYPICAL SILL DETAIL (RECESSED) SEE ALTERNATE OPTION DETAIL FINESTOP OR FINESTOP RA BASFF WS FLASH ALTERNATE OPENING PROTECTION OPTION FOR WINDOW SILL (WS FLASH MAY BE APPLIED UNDER OR OVER THE FINESTOP OR FINESTOP RA). EXTEND FLASHING MIN. 50 mm (2 ) OVER EIFS FLASHINGS ARE BY OTHERS AND SHALL BE AS PER DESIGN/CODE REQUIREMENTS
9 ROOF SYSTEM ROOF EDGE FLASHING MIN. 50 mm (2 ) SEALANT FINESTOP, FINESTOP RA OR AM-11 TYPICAL ROOF EDGE FLASHING DETAIL METAL COPING MIN. 50 mm (2 ) SEALANT FINESTOP, FINESTOP RA OR ROOF SYSTEM AM-12 TYPICAL METAL COPING DETAIL
10 Pebbletex Adhered Mat Design FLASHINGS ARE BY OTHERS AND SHALL BE AS PER DESIGN/CODE REQUIREMENTS EPS CAP SELF-ADHERING MESH TAPE (9 ) EMBEDDED IN FINESTOP OR 9 SHEATHING FABRIC EMBEDDED IN FINESTOP RA FINESTOP, FINESTOP RA OR 12 6 SEALANT MIN. 25 mm (1 ) FLASHING ROOF SYSTEM MIN. 203 mm (8 ) AM-13 TYPICAL PARAPET CAP DETAIL FLOOR SLAB FINESTOP, FINESTOP RA OR WIDTH PER DESIGN MIN. 19 mm (3/4 ) BASF COLOR COAT SLIP TRACK AM-14 TYPICAL EXPANSION JOINT DETAIL AT FLOORLINE
11 FINESTOP, FINESTOP RA OR JOINT WIDTH PER DESIGN BASF COLOR COAT ACCEPTABLE SUBSTRATE AM-15 TYPICAL EXPANSION JOINT AT CHANGE IN SUBSTRATE FINESTOP, FINESTOP RA OR PEBBLETEX CLASSIC PB SYSTEM EXTEND FINESTOP OR FINESTOP RA A MIN. OF 102 MM (4 ) ONTO SOFFIT. USE APPROPRIATE REINFORCEMENT AT CORNER. AM-16 TYPICAL SECTION AT FASCIA/SOFFIT
12 Pebbletex Adhered Mat Design FINESTOP, FINESTOP RA OR BASF COLOR COAT WIDTH PER DESIGN FINESTONE REINFORCING MESH AM-17 TYPICAL EXPANSION JOINT DETAIL FINESTOP, FINESTOP RA OR SEC- ONDARY MOISTURE SEALANT AT PERIMETER OF PENETRATION MIN. 13 mm (1/2 ) BASF COLOR COAT FINESTONE REINFORCING MESH AM-18 TYPICAL PIPE PENETRATION
13 FINESTOP, FINESTOP RA OR STRONG 15 OR HI-IMPACT 20 EMBEDDED IN FINESTONE BASE COAT STANDARD MESH REINFORCING MESH OR INTERMEDIATE 6 EMBEDDED IN FINESTONE BASE COAT BUTT EDGE OF STRONG 15 OR HI-IMPACT 20 TO CORNER MESH A CONTINUOUS OVERLAY OF STANDARD MESH OR INTERMEDIATE 6 IS REQUIRED OVER STRONG 15, HI-IMPACT 20 OR CORNER MESH. SELF-ADHERING MESH TAPE (9 ) EMBEDDED IN FINESTOP OR 9 SHEATHING FABRIC EMBEDDED IN FINESTOP RA CORNER MESH EMBEDDED IN BASE COAT AM-19 TYPICAL CORNER MESH APPLICATION WITH STRONG 15 OR HI-IMPACT 20 (PLAN VIEW) A CONTINUOUS OVERLAY OF STANDARD MESH OR INTERMEDIATE 6 OR 12 IS REQUIRED OVER CORNER MESH. FINESTOP, FINESTOP RA OR FINESTONE INSULATION BOARD STANDARD MESH REINFORCING MESH OR INTERMEDIATE 6 EMBEDDED IN FINESTONE BASE COAT SELF-ADHERING MESH TAPE (9 ) EMBEDDED IN FINESTOP OR 9 SHEATHING FABRIC EMBEDDED IN FINESTOP RA CORNER MESH EMBEDDED IN BASE COAT FINESTONE REINFORCING MESH AM-20 TYPICAL CORNER MESH APPLICATION WITH STANDARD MESH, INTERMEDIATE 6 OR 12 (PLAN VIEW)
14 Pebbletex Adhered Mat Design SET FLANGE IN SEALANT FINESTOP TM, FINESTOP RA OR SMALL LIGHT FIXTURE WIRE OPENING AM-21 TYPICAL LIGHT FIXTURE FINESTOP TM, FINESTOP RA OR SELF-ADHERING MESH TAPE (4 ), 4 SHEATHING FABRIC OR FLASHING SEALANT FOUNDATION AM-22 TYPICAL TERMINATION AT FOUNDATION MIN. 50 mm (2 ) MAX. 305 mm (12 ) IF IS USED IN LIEU OF FINESTOP OR FINESTOP RA, ENSURE BARRIER IS PROPERLY LAPPED OVER THE FLASHING FLANGE. TERMINATE PEBBLETEX ADHERED MAT DESIGN SYSTEM MIN. 203 mm (8 ) ABOVE GRADE.
15 FINESTOP TM, FINESTOP RA OR BASF COLOR COAT MIN. 25 mm (1 ) BACKER ROD, SEALANT AND WEEP TUBE FOUNDATION AM-23 TYPICAL TERMINATION AT FOUNDATION (FLUSH) STEP FLASHING FINESTOP TM, FINESTOP RA OR PEBBLETEX ADHERED MAT DESIGN KICK-OUT FLASHING MUST BE ANGLED 100 MIN.TO ALLOW FOR PROPER DRAINAGE. KICK-OUT FLASHING SEAMS MUST BE SOLDERED OR SEALED WITH APPROPRIATE SEALANT. TERMINATE PEBBLETEX ADHERED MAT DESIGN MIN. 50 mm (2 ) ABOVE ROOF. MIN. 100 mm (4 ) MIN. 50 mm (2 ) BUILDING PAPER ROOF SHINGLES DRIP EDGE KICK-OUT FLASHING AM-24 TYPICAL KICK-OUT FLASHING DETAIL
16 Pebbletex Adhered Mat Design For the most current version of this literature, please visit our website at BASF Corporation - Wall Systems 3550 St Johns Bluff Rd South Jacksonville, Florida P: F: BASF Corporation rev
Acrowall-CP Cement-Plaster Stucco
Acrowall-CP Cement-Plaster Stucco SYSTEM DESCRIPTION 1033764 Typical Details 1. ACROWALL-CP SYSTEM APPLICATION 2. ACROWALL-CP SYSTEM APPLICATION WITH EPS BOARD 3. ACROWALL-CP SYSTEM ISOMETRIC VIEW 4. SURFACE
More informationBest Materials LLC distributes backer rod, caulking and sealants for all types of EIFS joints and penetration sealing applications.
Best Materials LLC distributes backer rod, caulking and sealants for all types of EIFS joints and penetration sealing applications. EXTERIOR INSULATION & FINISH SYSTEM CONSTRUCTION Data Published Courtesy
More informationCFDTT-01. Control Joint Study (General)
Trim Method Classic Method Notes: Control joints are required and should be located by the designer at the following locations on the construction documents: 144 sf (13.4 sm) is the maximum overall area
More informationDW VERTICAL INSTALLATION
AR-PJ-01-DW5V AR-PJ-02-DW5V AR-PJ-03-DW5V AR-PJ-04-DW5V AR-BS-01-DW5V AR-BS-02-DW5V AR-OC-01-DW5V AR-OC-02-DW5V AR-OC-03-DW5V AR-IC-01-DW5V AR-IC-02-DW5V AR-IC-03-DW5V AR-FO-01-DW5V AR-FO-02-DW5V AR-FO-03-DW5V
More informationDW HORIZONTAL INSTALLATION
AR-PJ-01-DW2H 2" HORIZONTAL PANEL JOINT AR-PJ-02-DW2H 2" VERTICAL PANEL JOINT AR-PJ-03-DW2H 3" HORIZONTAL PANEL JOINT AR-PJ-04-DW2H 3" VERTICAL PANEL JOINT AR-PJ-05-DW2H CUSTOM REVEAL AR-PJ-06-DW2H DW-2000S
More informationRECOMMENDED INSTALLATION PROCEDURE LEVEL 3
Step 1. Install Sill Flashing Product: 9" or 12" RainBuster #440 SubZero Flashing Tape 1.A Flashing Length = (Rough Opening Width) + 12" 1.B Install sill flashing flush with the sill of the rough opening.
More informationQuick Reference Guide For MoistureFree Certified Inspectors and Contractors
Quick Reference Guide For MoistureFree Certified Inspectors and Contractors Topic Page No. Critical Elements Of The Kickout 2 Bad Kickout Examples 3 Raintek Kickout By Demand Products 4 Inspecting and
More informationRECOMMENDED INSTALLATION PROCEDURE LEVEL 3
45 45 6 6 Step 1. Modify Weather Resistive Barrier 1.A Cut the weather resistive barrier flush to the recessed opening (per diagram). Remove the cut away weather resistive barrier, exposing recessed opening
More informationKS42 MF SERIES - HORIZONTAL INSTALLATION
CI-DS-01-KSMF H CI-PJ-01-KSMF H CI-PJ-02-KSMF H CI-PJ-03-KSMF H CI-PJ-04-KSMF H CI-PJ-05-KSMF H CI-PJ-06-KSMF H CI-PJ-07-KSMF H CI-PJ-08-KSMF H CI-PJ-09-KSMF H CI-PJ-10-KSMF H CI-PJ-11-KSMF H CI-PJ-12-KSMF
More information900 SERIES WALL PANELS
CI-DS-01-900 CI-PP-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-PJ-03-900 CI-BS-01-900 CI-BS-02-900 CI-BS-03-900 CI-BS-04-900 CI-BS-05-900 CI-OC-01-900 CI-OC-02-900 CI-IC-01-900 CI-FO-01-900 CI-FO-02-900 CI-FO-03-900
More informationWEB BASED CORE APPLICATION SPECIFIC INSTALLATION INFORMATION AND METHODS
CORE WEB BASED CORE APPLICATION SPECIFIC INSTALLATION INFORMATION AND METHODS Proper Window & Door Flashing Although all possible measures have been taken to insure the accuracy of the material presented,
More information400 SERIES VERTICAL INSTALLATION
CI-DS-01-400V CI-PJ-01-400V CI-PJ-02-400V CI-PJ-03-400V CI-BS-01-400V CI-BS-02-400V CI-BS-03-400V CI-BS-04-400V CI-BS-05-400V CI-OC-01-400V CI-OC-02-400V CI-IC-01-400V CI-IC-02-400V CI-FO-01-400V CI-FO-02-400V
More informationInstallation Recommendations for Finless Frame Doors
Installation Recommendations for Finless Frame Doors These installation recommendations are made available by MI Windows and Doors, LLC (MI) to assist with the integration of finless or flange sliding
More informationForceField Air & Water Barrier System. installation instructions
ForceField Air & Water Barrier System installation instructions Protection and Performance inside and out The ForceField air and water barrier system consists of engineered wood sheathing panels laminated
More informationAll Window Installation Instruction
1 All Window Installation Instruction Hurd Window Installation Instructions for Nail Fin & Wood Brick Mould Units Nail Fin Windows See Pages 2-11 Wood Brick Mould Windows See Pages 2-6, 8 & 12BM - 14BM
More informationMAXIMUM PANEL ATTACHMENT FASTENER SPACING IS 24" O.C. ALL FASTENERS TO PENETRATE WOOD 3/4" MIN. AND METAL FRAMING 1/2" MIN.
PLYWOOD SHEATHING DMI SOFFIT PANEL #10-13 GP PANCAKE HEAD (JC) - J CLOSURE (LC) - L CLOSURE #9-15 X 1 1/2" WOODZAC GP APPROVED MOISTURE BARRIER SOFFIT TO WALL PANEL WPRP-H-01-00 APPROVED MOISTURE BARRIER
More informationL:\Document Control\DR Drafting\Records\Royce\Facades\Plank\US BenchmarkTM By Kingspan 40% RGB Gold 2013.jpg FACADES - BRICK INDEX SHEET
KPV-DS-01-BRH KPV-PJ-01-BRH KPV-PJ-02-BRH KPV-PJ-03-BRH KPV-BS-01-BRH KPV-BS-02-BRH KPV-BS-03-BRH KPV-OC-01-BRH KPV-IC-01-BRH KPV-FO-01-BRH KPV-FO-02-BRH KPV-FO-03-BRH KPV-SJ-01-BRH KPV-PR-01-BRH KPV-LE-01-BRH
More informationEagle clad double-hung window installation instructions
Eagle clad double-hung window installation instructions These instructions are for typical installation in new typical wood frame wall construction. These instructions and methods are not intended for
More informationRECOMMENDED INSTALLATION PROCEDURE LEVEL 3
Products: 12" RainBuster #415 Self-Adhered Flashing Membrane-40mil 12" RainBuster #415 Self-Adhered Flashing Membrane-25mil 12" RainBuster #420 Nail On Flashing Membrane-25mil RainBuster #430-4.0 Recess
More information3M Air and Vapour Barrier 3015 Technical guide
3M Air and Vapour Barrier 3015 Technical guide Product overview Typical physical properties For installation ease and flexibility, 3M Air and Vapour Barrier 3015 High performance 3M acrylic adhesive grabs
More informationUNIT 5: EXTERIOR DOORS AND WINDOWS
KEY CONCEPTS 1. Identify tools needed for exterior door and window installation 2. Last step to weather proofing the home 3. Steps to installing exterior doors and windows 4. Maintenance and safety of
More informationWindows Installed into Walls with Polyiso and Wood Framing. Installation Instructions Standard Method Revised 10/24/2016
Windows Installed into Walls with Polyiso and Wood Framing Installation Instructions Standard Method Revised 10/24/2016 Background There are many acceptable ways to mount and detail windows for support
More informationDuPont Flashing Systems Installation Guidelines. Integral Flanged Door Before water-resistive. Version 2
DuPont Flashing Systems Installation Guidelines Helping you get the job done right Integral Flanged Door Before water-resistive barrier (wrb) is installed Version 2 Table of Contents Applicable Products...2
More informationA REFERENCE GUIDE OF TYPICAL RAINSCREEN WALL AND WINDOW DETAILS
WARRANTY PROVIDER ACCEPTED A REFERENCE GUIDE OF TYPICAL RAINSCREEN WALL AND WINDOW DETAILS Per: 2006 B.C.B.C. Part 9 DISCLAIMER THE INFORMATION CONTAINED IN THIS DOCUMENT REPRESENTS CURRENT WOOD FRAME
More informationTABLE OF CONTENTS A-1...TABLE OF CONTENTS A-2...GENERAL NOTES B-1 & B-2...GENERAL INFORMATION
TABLE OF CONTENTS PAGE NUMBER: DETAIL DESCRIPTION A-1...TABLE OF CONTENTS A-2...GENERAL NOTES B-1 & B-2...GENERAL INFORMATION MATRIX DETAILS C-1...FASCIA/SOFFIT DETAIL with ANGLE C-2...BUILDING/SOFFIT
More informationThe better way to build TM. Installation Manual ROOF SIPs
The better way to build TM Installation Manual ROOF SIPs August 2017 ROOF SIPs Installation Manual Table of Contents Topics General Requirements.................................... 3 Materials..............................................
More informationWindows Installed into Walls with Polyiso and Wood Framing. Installation Instructions Picture Frame Method Revised 10/24/2016
Windows Installed into Walls with Polyiso and Wood Framing Installation Instructions Picture Frame Method Revised 10/24/2016 Background There are many acceptable ways to mount and detail windows for support
More informationC.00. Ullrich Aluminium Co. Ltd. Ulltraclad Aluminium Cladding September Wall Batten Elevation. Horizontal battens between verticals at soffit
Horizontal battens between verticals at soffit 2 C.04 600 600 600 600 Cavity batten at 600 mm centres 1 C.03 Batten fixing points 1 C.04 1 C.07 1 C.12 1 C.13 1 C.14 Meter Box Window 1 C.08 1 C.09 800 800
More informationULTRA WINDOW & DOOR EXPANDERS AND RECEIVERS INSTALLATION INSTRUCTIONS
ULTRA WINDOW & DOOR S AND RECEIVERS INSTALLATION INSTRUCTIONS! CAUTION: *REMEMBER SAFETY FIRST* Proper Eye and! Hearing Protection must always be worn during installation of all window and door products.
More informationInstallation Instruction 3-D Model 3D 03/01/17. 0 Flush Siding Horizontal System N/C WPS, Inc.
I B D L K C E G M F A H J Installation Instruction 3-D Model 3D 03/01/17 Detail: System Type: Scale: Drawn By: 0 Flush Siding Horizontal System N/C WPS, Inc. Wall Panel System, Inc. 15/16" 1 1/4" Bottom
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More informationTHESE DETAILS ARE PROVIDED AS A GUIDELINE FOR PROPER PANEL AND ASSOCIATED COMPONENT INSTALLATION, AND ARE BASED ON INDUSTRY ACCEPTED PRACTICES.
KPV-DS-01-MTLH C & I DISCLAIMER KPV-PJ-01-MTLH EXPANDED PANEL JOINT KPV-PJ-02-MTLH ENGAGED PANEL JOINT KPV-PJ-03-MTLH INTERMEDIATE SUPPORT KPV-FS-01-MTLH MULTI-STORY FIRE STOPPING DETAIL KPV-FS-02-MTLH
More informationRead guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed
More informationNEW HOME WARRANTY A REFERENCE GUIDE FOR TYPICAL WALL AND WINDOW DETAILS (RAINSCREEN SYSTEM) SHOWN AS FIBRE CEMENT CLADDING
NEW HOME WARRANTY A REFERENCE GUIDE FOR TYPICAL WALL AND WINDOW DETAILS (RAINSCREEN SYSTEM) SHOWN AS Reference Guide 0.1 GENERAL 0.1 Reference Guide 0.2 Index 0.3 Disclaimer & Limitations 0.4 General Notes
More informationINSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS
2012 Pella Corporation Part Number: 80WH0101 INSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS Installation Instructions for Typical Wood Frame Construction.
More informationPRIMED STRAND REVERSIBLE SHAKE
PRIMED STRAND REVERSIBLE SHAKE PRIOR TO INSTALLATION Inspect product for any issues before installing (breakage, surface defects, foreign objects). Do not install questionable product. Report any problems
More informationFlashing Materials. Rough Opening Preparation
Installation Instructions for CertainTeed New Construction Windows Handling vinyl windows CAUTION: Always store vinyl windows and doors in an upright position on a slight angle. Never lay them flat or
More informationInstallation Instructions for Standard Lap and Self-Aligning Lap Siding
Installation Instructions for Standard Lap and Self-Aligning Lap Siding 7/16 in. Standard Laps Include: All Old Mill Widths, Cedar Shake Lap and Smooth Lap 1/2 in. Self-Aligning Include: 8 in. and 12 in.
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More informationBest Barns USA. Regency Deluxe. 8' x 12' Assembly Book. revised February 15, 2017
Best Barns USA Assembly Book revised February 15, 2017 Regency Deluxe 8' x 12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive, Greenville, PA 16125 This manual is copyrighted. Under
More informationBefore installation, check your local and state requirements for this type of install.
1 Remove Packaging & Inspect Your Patio Door Remove shipping materials such as corner covers or pads. 2 Inspect Rough Opening Verify that the width and height of the patio door are each 1/2" to 3/4" smaller
More informationInstallation of Fiberglass Windows
Installation of Fiberglass Windows Before you begin please read and understand these installation instructions. The following installation instructions are recommended by Norwood and failure to follow
More informationHydroGap Drainable Housewrap: Installation Instructions
METHOD I: MODIFIED O or CUT-BACK Method STEP 1 Unroll HydroGap Drainable Housewrap with blue spacers facing to the exterior and fasten to sheathing with nails, staples or cap fasteners. Fasteners should
More informationInstallation Guide for E-Series/Eagle Clad Mechanically Fastened Windows
Guide for E-Series/Eagle Clad Mechanically Fastened Windows Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place. Instructions
More informationShow them you're an InstallationMaster, and watch your business grow. InstallationMasters Training Manual Addendum Level RLC-1
Show them you're an InstallationMaster, and watch your business grow. InstallationMasters Training Manual Addendum Level RLC-1 August 2007 This addendum was developed by the InstallationMasters Institute
More informationPROVEN DEPENDABLE SUSTAINABLE
B/SOFFIT FP CLIP 24" O.C. MAX SECTION "A-A" PLYWOOD SHEATHING #10-13 GP PANCAKE HEAD FASTENER 12" O.C. A B/SOFFIT A (JC) - J CLOSURE DMI WALL PANEL PLYWOOD SHEATHING SOFFIT TO WALL PANEL FR10-V-01-00 B/SOFFIT
More informationNEW CONSTRUCTION PATIO DOOR INSTALLATION INSTRUCTIONS (WITH NAILING FLANGE)
NEW CONSTRUCTION PATIO DOOR INSTALLATION INSTRUCTIONS (WITH NAILING FLANGE) Slim Line & Classic French Style Patio Doors Materials included: (2) #10 x 2-1/2" Phillips Pan head keeper s (2) 3/8" Hole plugs
More informationDuPont Flashing Systems Installation Guidelines
Installation Instructions for Integral Flanged Windows in Recessed Openings BEFORE Water-Resistive Barrier (WRB) is installed DuPont Flashing Systems Installation Guidelines INSTALLATION INSTRUCTIONS FOR
More informationDuPont Flashing Systems Installation Guidelines
Installation Instructions for Field pplied Flanged EFORE Water-Resistive arrier (WR) Is Installed DuPont Flashing Systems Installation Guidelines INSTLLTION INSTRUCTIONS FOR FIELD PPLIED FLNGED WINDOW
More informationSECTION SHEET METAL FLASHING AND TRIM
SECTION 07620 PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Formed roof drainage sheet metal fabrications. 2. Formed low-slope roof sheet metal fabrications. 1.2 SUBMITTALS A. Shop Drawings: Show
More informationINSTALLATION INSTRUCTIONS DOUBLE-HUNG WINDOW WITH FINS
2012 Pella Corporation INSTALLATION INSTRUCTIONS DOUBLE-HUNG WINDOW WITH FINS Part Number: 802L0105 Installation Instructions for Typical Wood Frame Construction. These instructions were developed tested
More informationROOFING APPLICATION STANDARD (RAS) No. 130
ROOFING APPLICATION STANDARD (RAS) No. 130 1. Scope 1.1 This application Standard provides the minimum installation criteria for wood shingles and shakes. 2. Definitions 2.1 For definitions of terms used
More informationDuPont Flashing Systems Commercial Installation Guidelines
DuPont DuPont Flashing Systems Commercial Installation Guidelines FOR STOREFRONT WINDOW ON A KNEE WALL AFTER WRB IS INSTALLED Table of Contents Applicable Products... 2 Recommended Materials... 2 Optional
More informationSHEET METAL FLASHING AND TRIM Christ on the Mountain
SECTION 076200 - SHEET METAL FLASHING AND TRIM PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Compatibly with the bumping of flashings and trim as identified in the Membrane Roofing Section 075000.
More informationDMI FR1511 PANEL (JC) - J CLOSURE DMI WALL PANEL SOFFIT TO WALL PANEL PROVEN DEPENDABLE SUSTAINABLE METAL ENVELOPE SYSTEMS SINCE 1988
FP CLIP 24" O.C. MAX B/SOFFIT 5 1/2" SECTION "A-A" PLYWOOD SHEATHING #10-13 GP PANCAKE HEAD FASTENER 12" O.C. A B/SOFFIT A (JC) - J CLOSURE DMI WALL PANEL PLYWOOD SHEATHING SOFFIT TO WALL PANEL FR15-V-01-00
More informationInstallation Instructions
Installation Instructions HYDROGAP DRAINABLE HOUSEWRAP AND ACCESSORIES Page Basic Installation and Window Flashing: Pre-Installation Considerations 2 List of Approved Compatible Products 3 METHOD I: Modified
More informationInstallation Guide - Evolution Series Wood Siding
Installation Guide - Evolution Series Wood Siding The following instructions pertain to the installation of Fraser Wood Siding Evolution Series on a typical wood frame construction allowing for nail penetration
More informationKS SERIES - VERTICAL INSTALLATION
CS-DS-01-KSV CS DISCLAIMER CS-PJ-01-KSV KS42SL EXPANDED PANEL JOINT CS-PJ-02-KSV KS42SL ENGAGED PANEL JOINT CS-PJ-03-KSV KS45SL EXPANDED PANEL JOINT CS-PJ-04-KSV KS45 FLAT ENGAGED PANEL JOINT CS-PJ-05-KSV
More informationINSTALLATION SHOP DRAWINGS FOR MINNEAPOLIS, MN
MINNEAPOLIS, MN 2-0- 2-- General Notes Abbreviations Deviations from Architectural Specifications Deviations from Architectural Drawings ALUM. = ALUMINUM B.O. = BY OTHERS CONT. = CONTINUOUS. = CLEARANCE
More informationROOFING APPLICATION STANDARD (RAS) No. 130 INSTALLATION CRITERIA FOR WOOD SHINGLES AND SHAKES APPLICATION
ROOFING APPLICATION STANDARD (RAS) No. 130 INSTALLATION CRITERIA FOR WOOD SHINGLES AND SHAKES APPLICATION 1. 2. 3. Scope 1.1 This application standard provides the minimum installation criteria for wood
More informationTHESE DETAILS ARE PROVIDED AS A GUIDELINE FOR PROPER PANEL AND ASSOCIATED COMPONENT INSTALLATION, AND ARE BASED ON INDUSTRY ACCEPTED PRACTICES.
FRKPV-DS-01-MTLH FRKPV-PJ-01-MTLH FRKPV-PJ-02-MTLH FRKPV-PJ-03-MTLH FRKPV-FS-01-MTLH FRKPV-FS-02-MTLH FRKPV-BS-01-MTLH FRKPV-BS-02-MTLH FRKPV-BS-03-MTLH FRKPV-BS-04-MTLH FRKPV-OC-01-MTLH FRKPV-IC-01-MTLH
More informationSun Windows General Information New Construction Sliding Door Installation Instructions H F
A G B D C H F H E H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape
More informationTHERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE)
THERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE) fig.3 Casement, Awning, Fixed Casement, Direct-Set, Double-Hung, Single-Hung & Horizontal Slider Windows Materials
More informationMULTI-STORY FIRE STOPPING ASSEMBLY FRAMED OPENING JAMB (LOW CELL) INDEX SHEET
KPH-DS-01-MTLV KPH-PP-01-MTLV KPH-PP-02-MTLV KPH-PJ-01-MTLV KPH-PJ-02-MTLV KPH-PJ-03-MTLV KPH-PJ-04-MTLV KPH-PJ-05-MTLV KPH-FS-01-MTLV KPH-FS-02-MTLV KPH-FS-03-MTLV KPH-BS-01-MTLV KPH-BS-02-MTLV KPH-BS-03-MTLV
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows with Exterior Trim or Nail Fin (JII024)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows with nailing fin or primed wood windows with exterior trim. While the
More informationDETAIL CROFT FARM OUTBUILDING RESTORATION TOWNSHIP OF CHERRY HILL, NEW JERSEY
2x DIMENSIONAL LUMBER SISTER/SCAB REINFORCEMENT MEMBER 060523 3/8" A304 BOLT @ 8" O.C., STAGGERED EXISTING FRAMING MEMBER SECTION PROVIDE MIN EDGE DISTANCES AS SHOWN, TYP. ELEVATION REFER TO IFICATION
More informationWESTERN WAVE Panel. Horizontal Installation and Technical Information
WESTERN WAVE Panel Horizontal Installation and Technical Information Western States Western Wave Wall and Soffit Panels Installation, Flashings & Shop Drawing Detail Guide Table of Contents Section Page
More informationDuPont Self-Adhered Flashing Systems Products
DuPont Self-Adhered Flashing Systems Products Installation of Integral Flanged Windows in Recessed Openings Before Water-Resistive Barrier (WRB) Is Installed For up to 4" Recess Using Single and Double
More informationWESTERN WAVE Panel. Vertical Installation and Technical Information
WESTERN WAVE Panel Vertical Installation and Technical Information Western States Western Wave Wall and Soffit Panels (Vertical) Installation, Flashings & Shop Drawing Detail Guide Section Notes to Designer
More informationBest Barns USA Assembly Book Revised November 3, 2016
Best Barns USA Assembly Book Revised November 3, 2016 the Aspen II 12' x 8' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive, Greenville, PA 16125 This manual is copyrighted. Under the
More informationUC SANTA CRUZ STANDARD PLASTER INSTALLATION AND DETAILS SEVERE WEATHER
CAMPUS STANDARDS APPENDIX I UC SANTA CRUZ STANDARD PLASTER INSTALLATION AND DETAILS SEVERE WEATHER February 21, 2014 WINDOW INSTALLATION SEQUENCING GUIDE Issued By: Pyatok Architects and Allana Buick &
More informationMetroCOTTAGE Shingle
Batten-less Installation Sept. 14, 2017 INSTALLATION WARNING! These install details are provided to demonstrate a recommended installation method for Metro Roof panels and accessories. used in the United
More informationTurada Hardwood Shingles and Shakes Installation instructions
1. General 1.1 Maximum Exposure: Maximum exposure for wood shingles and shakes shall comply with Table 1 herein, unless specifically specified in the roof assemblies Product Approval. 1.2 Solid and Spaced
More informationUC SANTA CRUZ STANDARD PLASTER INSTALLATION AND DETAILS STANDARD
CAMPUS STANDARDS APPENDIX H UC SANTA CRUZ STANDARD PLASTER INSTALLATION AND DETAILS STANDARD December 5, 2014 Window Installation Sequencing Guide Pyatok Architects and Allana Buick & Bers Inc. 12/5/2014
More informationBuilding Wrap and Flashing
Insulati o n First Revision November 2017 Building Wrap and Flashing INSTALLATION GUIDE FOR RESIDENTIAL & LIGHT COMMERCIAL APPLICATIONS 1. General Information 2. Usage & Limitations 5. Handling & Storage
More informationInstallation Instructions
Installation Instructions SLICKER CLASSIC RAINSCREEN Page List of Approved Compatible Products 2 Nail Selection Guide 3 General Installation 4 Insulation Board Installation 5 EIFS Installation 6 Top of
More informationNEW CONSTRUCTION, REPLACEMENT AND FLUSH FIN REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS
NEW CONSTUCTION, REPLACEMENT & FLUSH FIN WINDOWS NEW CONSTRUCTION, REPLACEMENT AND FLUSH FIN REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS IMPORTANT! READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.
More informationSEAL PLATE SP4413 VERTICAL SP4414 1"[25] VERT. PANEL JTS. 1/2"[13] INTERM. SPLICES DESIGN LOADS AND SLAB EDGE DISTANCES. 1 2 NOM.
3 COL 5 16GA. ANGLE SP4413 VERTICAL SEE SUPPORT DRAINGS 1 7/16 SEAL PLATE @ VERT. JNT 1/2 [13] Ă DETAILER NOTE OPTIONAL INSULATION HEN REQUIRED. OF SEAL PLATE PANEL MODULE 2.500 FROM SHELF OF TR. TO TOP
More informationInstallation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
More informationAPRON FLASHING NOTES: SHEET METAL APRON FLASHING WITH HEMMED EDGE RAGGLE SEALANT UNDERLAYMENT TURNED UP WALL
SHEET METAL APRON FLASHING WITH HEMMED EDGE SEALANT SHEET METAL COUNTERFLASHING (SEE NOTE No.1) RAGGLE UNDERLAYMENT TURNED UP WALL SHEET METAL STEP FLASHING SOLDER OR SEAL CORNERS ASPHALT SHINGLES NOTES:
More informationConstruction details: Master-C type profiles and joints:
Construction details: Master-C type profiles and joints: Master-C 3g 32 mm. (1 1/4 ) 1000 mm. (39 3/8 ) outer face inner face 10.5 fixing details: sealing washers shall be installed through a 2-3/8 x 1-9/16
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 9/29/2017 Installation Guideline Disclaimer This document contains general installation
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 08/31/2018 Installation Guideline Disclaimer This document contains general installation
More informationSun Windows General Information New Construction Hinged Door Installation Instructions
A G H F H H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape F. Apply
More informationwindow installation Guide wood FRaMinG New Construction
window installation Guide wood FRaMinG New Construction IMPORTANT NOTICES AND INFORMATION Read these instructions in their entirety prior to installing windows. Any local building code requirements supersede
More informationInstallation Instructions for Panel Siding and Soffit
Installation Instructions for Panel Siding and Soffit 7/16 in. Panels Include: Sturdy Panel, Square Edge, 3/4 in. Channel and Reverse Board and Batten (RB&B) 1/2 in. Panels Include: Adobe Shiplap and 808
More informationInstallation Instructions for Old Mill Shingle and Designer Shake Lap Siding
Installation Instructions for Old Mill Shingle and Designer Shake Lap Siding Includes: Cove, Craftsmen Staggered, Diamond, Fish Scale, Octagon, Round and Old Mill Shingle Lap Important: Read and understand
More informationAssembly Book. 10' x 12' the Cambridge II. revised June 13, 2014
Assembly Book revised June 13, 2014 the Cambridge II 10' x 12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted. Under the
More informationInstallation Guidelines. Next Dimension. Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window
Installation Guidelines Next Dimension Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window Windsor Windows & Doors Windsor Windows & Doors 900 S. 19 th St. 2210 Stafford St. Extn
More informationFibre Cement G C. Batten Fixing Setout ST-01. Jan 2014 A4 PROFILE DATE SCALE DETAIL DETAIL NO. Plank joint. 600mm stud crs.
Plank joint 600mm stud crs 600mm 600mm 600mm Horizontal Structural Timber Cavity atten 50x20mm H3.1 atten fixing points 800mm 800mm 300mm 800mm Max. Nog spacing 50mm All intermediate battens to be 50x20mm
More informationINSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS
2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed
More informationBest Barns USA. the Brookhaven 10' x 16' Assembly Book. revised March 23, 2016
Best Barns USA Assembly Book revised March 23, 2016 the Brookhaven 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationAdorn Mortarless Stone Veneer Installation Natural Concrete Products
Adorn Mortarless Stone Veneer Installation Adorn Mortarless Stone Veneer can be used on new or existing construction. Adorn is nailed or screwed onto the wall; therefore no brick ledge is required. Adorn
More informationWALL TO FABRICATED FLOOR
WALL TO FABRICATED FLOOR PERIMETER WALL IS HELD IN PLACE BY WOODEN STRIP SCREED OPTIONAL NSF COVED FLOOR IS SHOWN PARTITION WALL IS HELD IN PLACE BY WOODEN STRIP SCREED OPTIONAL NSF COVED FLOOR IS SHOWN
More informationLP SmartSide Soffit ON SITE STORAGE PREPARATION. Application Instructions Vented and Non-Vented Smooth Finish or Cedar Texture. General Information
Application Instructions Vented and Non-Vented Smooth Finish or Cedar Texture A B A - Open / Closed (Page 5) B - Vented (Page 6) ON SITE STORAGE Store off the ground well supported, on a flat well-drained
More informationBuilding Wrap and Flashing
Insulati o n Fifth Revision January 2019 Building Wrap and Flashing INSTALLATION GUIDE FOR RESIDENTIAL & LIGHT COMMERCIAL APPLICATIONS 1. General Information 2. Usage & Limitations MAX, HPW, VW, RainDrop
More informationTools required by installer: Materials required by installer:
Installation Guidelines For Quaker Window Products Vinyl product line (Single Hung, Double Hung, Sliding Window, Fixed Window, Casement, Awning, and Hopper) Installer: Read these instructions completely
More informationFMA/AAMA/WDMA Installation Update FMA Spring Conference Duck Key, Florida April 27, 2010
FMA/AAMA/WDMA Installation Update FMA Spring Conference Duck Key, Florida April 27, 2010 James D. Katsaros, PhD DuPont Building Innovations FMA Installation Committee Chairman Key Flashing & Installation
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationAssembly Book. 10' x 16' the Cambridge II. revised July 15, 2014
Assembly Book revised July 15, 2014 the Cambridge II 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted. Under the
More information