INTRODUCTION. This simple file creates a neat table. for small children to use for multiple purposes. Weather drawing with crayons, putting puzzles
|
|
- Tyler Summers
- 5 years ago
- Views:
Transcription
1 Kids Work Table Remember children will be working on this table so check with your local paint supplier to find one safe for children. A latex based paint was used for this example. Written By: Feitan Page 1 of 7
2 INTRODUCTION This simple file creates a neat table for small children to use for multiple purposes. Weather drawing with crayons, putting puzzles together or having an afternoon snack this work table is strong and solid. If desired this project can be modified to a longer or deeper size Page 2 of 7
3 Step 1 Kids Work Table Materials: 3/4 furniture grade plywood Minimum Cutting Area: 4 x 8 Bit Size: 1/4 1. Always read the entire project details before starting to cut the file yourself. 2. Account for the thickness of the physical material on hand and the material thickness in the file. 3. This file is zeroed to the tables surface, Zero your bit to the tables surface Page 3 of 7
4 Step 2 1. As the file starts cutting the profile of the parts make sure the cut is going all the way through the work piece and into the table surface. If you need to adjust any part of the file make sure you do not remove the hold down or you will loose position. 2. Included with the cut file is a hold down toolpath that shows where it is safe to put screws. Run this file separately from the cut file so you can screw down the work piece, or if you have a different size board or different type of hold down disregard the file. ( See image 1 ) 3. Tabs are use to hold all the pieces to the scrap wood attached to them. Use a utility knife to score these edges. A carpet knife works well to score the tabs before lifting the pieces up. Never try to push a piece out without cutting the tab, it will tear the grain on your project. Sand remaining tab flat. ( See image 2 ) Page 4 of 7
5 Step 3 4. All of the edges for this project should be rounded over to ensure children do not bump into a sharp edge. ( See image 1 ) 5. There is an extra toolpath in this file that cuts out a 30 square. This does not have to be done, it is simply put in the file to cut this piece out so it can be used for another project. ( See image 2 ) 6. Again, to avoid a 30 x 30 piece from going to scrap, a extra toolpath was added to cut this square out. ( See image 3 ) Step 4 7. Sand, sand and sand. Make sure there are no loose pieces of wood or sharp corners that could get stuck in childrens fingers. ( See image 1 ) 8. The first assembly step is to assemble the supports to the undersides of the seats and table top. ( See image 2 ) 9. Apply a good amount of glue inside each mortise and rub around with a brush. This gets glue on all of the sides and strengthens the joint. ( See image 3 ) Page 5 of 7
6 Step Keep this upside down and clamped until the glue has set. Glue has a tendency to drip out of the dog bones, doing this will prevent this from happening. ( See image 1 ) 11. Fill the large mortises on one of the end pieces. Assemble each seat piece and the top piece. ( See image 2 ) 12. Once the three pieces are attached to the first end piece, let the glue setup before flipping over to the other side or the glue will drip like noted before. ( See image 3 ) Step Attach the other end piece in the same fashion as before. Let the glue dry overnight before testing the durability of this table. ( See image 1 ) 14. Whether painting or staining it is easier to do all of the undersides before moving to the outer part of the project. This will help keep your hands from getting covered and messy. ( See image 2 ) 15. Spend some time putting a few coats on and really make this project come to life. ( See image 3 ) Page 6 of 7
7 Step 7 Kids of all sorts will find many different uses for this table. One modification that has become popular is adding handles in each end so the table is easier to be moved around the house. Project Files: Kids Work Table Tutorial Kids Work Table Project Files This document was last generated on :08:17 PM Page 7 of 7
Scissor Stool. Written By: Feitan
Scissor Stool If the stool is going to be kept indoors simply rub all the pieces with a Minwax WipeOn Poly before assembling the stool. If it is going to go outdoors use Minwax SparUrathane and coat all
More informationSmoker. Written By: Feitan
Smoker Smoking meat has been around for hundreds of years. Now with this simple smoker one can bring back to life the ancient methods of preserving meats and adding the smoky flavor. Written By: Feitan
More informationProject: Smoker Overview: Smoking meat has been around for. Materials: 3/4 plywood, 7-48 of 1/2 dowel,
Project: Smoker Overview: Smoking meat has been around for hundreds of years. Now with this simple smoker one can bring back to life the ancient methods of preserving meats and adding the smoky flavor.
More informationProject: Bistro Set Overview: This is a set of four stools and one
Project: Bistro Set Overview: This is a set of four stools and one table that create a complete bistro set. Works great both indoors and out. By removing only a couple screws the entire project comes apart
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationProject: Trebuchet Overview: This medieval launcher would reek. Materials: 3/4 plywood, 2 of 5/8 threaded. Minimum Cutting Area: 2 sheets of plywood
Project: Trebuchet Overview: This medieval launcher would reek havoc on enemies castles. However, the modern day conversion using 20lbs of weight will easily through a tennis ball the length of a gymnasium.
More informationHarriet Chair with Modifications
Harriet Chair with Modifications This modification of the Harriet chair includes a slat back, padded seat, and is 2 inches wider than the original plan. The overall dimensions of the finished chair: 38
More informationining Table Materials *Notes on Materials
D ining Table We looked around for the perfect table for the dining room. Some were too big, some too small, and most were just too expensive. So we built this one, and we are happy with the result. It
More informationOUTDOOR STOOL. ProWood Project Plan
ProWood Project Plan OUTDOOR STOOL With ProWood Professional Grade pressure-treated wood, you can easily build this sturdy stool and complement your outdoor deck, patio or yard furniture and expand your
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationShopBot Shop Stools for the Family
ShopBot Tools Project of the Month ShopBot Shop Stools for the Family Everyone needs an extra stool for the shop or house. When made with ¾ plywood, these stools are sturdy and stable. You can also make
More informationEXTREME LOAD no. TWO
1602 - EXTREME LOAD no. TWO Kit Features: 22' 4 " x 14' x 3'-6 Oversize Load 49mm (1.9") actual height Bolt Head Details Welded Load Mounting Fins Painting Handles Tools Required: Hobby Knife Tweezers
More informationComputer Desk. Project designed by April Wilkerson
Project designed by April Wilkerson Copyright WilkerDos.com 2018 Project plan Desk Page 2 of 16 Page 3 of 16 File cabinet Page 4 of 16 Metal base Page 5 of 16 Glue up Get started by gluing up boards for
More informationMudroom Unit. Page 1 of 25
Mudroom Unit www.andrewharriswoodwork.com Page 1 of 25 Introduction This plan makes a unit which is 66 ¾ inches tall, 39 ½ inches wide and 18 ½ inches deep. It was custom made for some friends to fit the
More informationCobra X Q Construction Tips Construction: Bel y pan
Cobra X Q Construction Tips : The white plastic in this kit is high impact styrene. It can be painted with most types of coatings if light coats are applied this is necessary due to the thickness of the
More informationARTS AND CRAFTS CHAIR
ARTS AND CRAFTS CHAIR 491 MATERIALS LIST--DINING CHAIR Key No. Size and description (use) A 2 1-3/4 x 1-3/4 x 16-1/4'' oak (front leg) B 2 1-3/4 x 3-3/4 x 40-1/2'' oak (rear leg) C 1 1-3/4 x 3-3/16 x 15''
More informationHudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]
[1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.
More informationThe following pages replace pages 7 thru 14 in the current printing of BUILDING THE PT ELEVEN. (As of December 2012.)This is a modified method for
The following pages replace pages 7 thru 14 in the current printing of BUILDING THE PT ELEVEN. (As of December 2012.)This is a modified method for gluing puzzle joints that we believe is simpler than the
More informationG. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead.
G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead. Cab. In order to ensure that the cab and tender would actually look right, as what often appears on a drawing is not always
More informationFlip Down Wall Art Desk [1]
[1] Submitted by Ana White [2] on Mon, 2011-09-19 15:07 [1] Additional Photos [3] Page 1 of 20 This one has been a looooong time in the making. I first came up with the ideas of a wall mounted desk last
More informationBUILDING A TREE BENCH
INSTRUCTIONS FOR A In just a few steps, we show you how to build your own tree bench and paint it perfectly. 1 SIDE PIECES OF THE SEATING SURFACE Purchase the materials from the enclosed list. Draw a 10
More informationPROJECT PLAN TOOL CHEST
BUILD IT WITH ROCKLER PROJECT PLAN TOOL CHEST FEATURING ROCKLER S BUILD QUESTIONS? Go to www.rockler.com or call 800-279-4441 Stock # Item 63420 1/4" x 24" x 30" Baltic Birch Plywood 63446 1/2" x 24" x
More informationDIY X Panel Side Table
DIY X Panel Side Table *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationI I. . i1 AD JUSTABLE SHELVES
ADJUSTABLE SHELVES HAD BEEN TRYNG TO WORK out a really simple (read "fast") way to make an elegant wooden version of the old standby, metal standards and brackets. Although have seen many commercial versions
More informationFlamingo. That s what I looked
Plans N O W w w w. P l a n s N O W. c o m flip-seat Storage Bench Flamingo. That s what I looked like as I stood in the doorway perched on one leg, with my other foot raised so that I could untie the laces
More informationKreg Tool Co. All Rights Reserved.
Version 1 p. 1 Materials: Lumber: Qty: Board 2 2x2s 3 ft. long 2 1x2s 8 ft. long 2 1x3s 8 ft. long 6 1x6s 10 ft. long INSTRUCTIONS: Supplies: 1 1 / 4" Kreg Screws (coarse thread for softwoods, fine thread
More informationServing Tray. When some good friends got married recently, An exercise in template-making yields a great gift project that s easy to duplicate
Serving Tray An exercise in template-making yields a great gift project that s easy to duplicate END Create from 3 8 2 8" piece. By Geoff Noden When some good friends got married recently, I decided to
More information7/8n2 Scale Plantation Coach
7/8n2 Scale Plantation Coach Introduction This small coach modeled in 7/8 n2 was inspired from a Hawaiian Railway Company plantation excursion car from the late 19 century. While not an exact replica,
More informationMid-Century Credenza Thoughtful details and modern joinery merge in this sleek design
Mid-Century Credenza Thoughtful details and modern joinery merge in this sleek design BY LIBBY SCHRUM Mid-Century Modern furniture has not been wildly popular since, well, the mid-century. But fashion
More informationBoxtrot. Tools. Materials:
Boxtrot Sneak downstairs with a little nog and chisel yourself a nice box to hold your New Year's resolutions. Materials: Cut List: 3/8" plywood - preferably high grade, seven-ply, cabinetmakers plywood
More informationDurable Outdoor Table
54 F I N E W O O D W O R K I N G Durable Outdoor Table Ipé table will seat six and weather many seasons B Y D A V I D B E D R O S I A N Last summer brought a new pool to our backyard. With it came more
More informationEasy Jewelry Box. Easy Jewelry Box 1
This easy to build dresser style jewelry box is designed to use standard board sizes you may already have on hand. Drawers are lined in felt and have felt covered bottoms to glide smoothly on the shelves
More informationCopyrighted Material Page 1
Compare to: Pottery Barn Teen Storage Bed System Skill Level: Beginner Working with the rest of the components in the Storage Bed Collection, the Small Hutch fits on top of the Storage Headboard and will
More informationBird Feeder. Tool Requirements
Bird Feeder Written and constructed by Craig Tilley This wooden bird feeder will be an attractive addition to your garden. Its wide trays allow plenty of room for birds to come and have a snack, and the
More informationThe Saint Paul Building
The Saint Paul Building Instructions for Assembly of The Saint Paul Building. Kit Contents: 65 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk. 3 each Window Glass Templates,
More informationCarcase Construction. Choosing and making the right joints. by Tage Frid
Carcase Construction Choosing and making the right joints by Tage Frid Furniture construction is broken down into two main categories: frame and carcase. In frame construction, relatively narrow boards
More informationFidelity & Guaranty Building
Fidelity & Guaranty Building N Scale Model Kit Instructions for Assembly of the Fidelity & Guaranty Building Kit Contents: 69 each laser cut acrylic parts. Sidewalk material 1 each Window Glass Templates
More informationDrum Trigger Project Part 2: Electric Bongo Case
Drum Trigger Project Part 2: Electric Bongo Case When I started this project, it seemed that the best implementation of Ray Wilson s drum trigger circuit would be as a sort of hand drum. Since I ve got
More informationFidelity & Guaranty Building
Fidelity & Guaranty Building Instructions for Assembly of the Fidelity & Guaranty Building Kit Contents: 69 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk base. 4 each
More informationGet the benefits of oil with the ease of latex
One of the most rewarding home improvement projects is putting a fresh coat of paint on your kitchen cabinets. A new color brightens up your kitchen, and can give it a complete updated look. But at the
More informationStand & Bowls. optional. Online Extra
Online Extra optional Stand & Bowls Once you make a bowl using the jig and technique from Woodsmith No. 229, it s only natural to see what else you can do with it. The starting point is to make copies
More informationThe Midtown Apartment Building
The Midtown Apartment Building Instructions for Assembly of The Midtown Apartment Building. Kit Contents: 70 each laser cut acrylic parts. 3 each sidewalk parts. 3each Window Glass Templates, 3 each Window
More informationTrestle Table and Benches Materials List
Project 18444EZ: Trestle Table and Benches In the early days of our country, trestle tables were popular because they could easily be disassembled and moved out of the way when not in use no small advantage
More informationCongratulations on your purchase of the Divided Light Door Set. This set will help you create beautiful cabinet doors with true divided light panels.
Divided Light Door Set User Instructions Congratulations on your purchase of the Divided Light Door Set. This set will help you create beautiful cabinet doors with true divided light panels. Following
More informationAbout.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
More information3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
More informationKitchen Upper Cabinet: Single Door Cabinets from Scratch
Kitchen Upper Cabinet: Single Door by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, disappointment,
More informationBuild Instructions for Towers of Doom
Build Instructions for Towers of Doom 1. Measure and cut 4 x 8 sheet of plywood in half (or ask Home Depot to do it!). You will use one 4 x 4 sheet for the course base. 2. Attach a support frame to the
More informationHow To Create An Entertainment Unit
How To Create An Entertainment Unit Materials required: 2 x Pine Panels - 1800mm x 450mm x 18mm 4 x Pine Panels - 310mm x 450mm x 18mm 1 x Pine Panels - 650mm x 450mm x 18mm 6 x Bun feet (your choice of
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: TOOLS: (2) 2x2x8 Ft. Boards Tape Measure (2) 1x4x8 Ft. Boards Pencil (4) 1x2x8 Ft. Boards Carpenter s Square (1) 4x4 Ft. Sheet of ¾-Inch Plywood Drill with 5/16-inch Drill Bit (1) 1 ½-inch Thick
More informationA Slim,Comfortable. In 1979 I spent five months designing. This system works for most chairs and uses common materials
A Slim,Comfortable This system works for most chairs and uses common materials An upholstered slip seat complements a beautiful chair. Using modern materials, it s not difficult to construct an elegant
More informationBuild your own Drawer unit. D3 / D4
Page1 Build your own Drawer unit. D3 / D4 1: Introduction. This guide will give you the plans, materials and how to information to build your own drawer unit. The dimensions given will fit a D3 or D4,
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationBUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
More informationElastic-powered Bus : Assembly Instructions
Elastic-powered Bus : Assembly Instructions Assembly Instructions 1. Carefully cut out the parts. 2. Fold along the dotted lines, making mountain or valley folds as indicated. 3. Attach the glue spots
More informationMorris Chair. Make the mortises in the legs before you shape the curve near the bottom or make cutouts on the top.
Morris Chair Make the mortises in the legs before you shape the curve near the bottom or make cutouts on the top. Make the mortises in the legs before you shape the curve near the bottom or make cutouts
More informationDesigned for Vectric by Michael Tyler. Show how crazy you are about your significant other with this free Crazy Heart project!
Project Tutorial Compatible with: (or greater) and (or greater) Sample Carved with: ShopBot Buddy PRSalpha BT48 www.shopbottools.com Featuring compatibility with nearly all CNC Machines Show how crazy
More informationKitchen Upper Cabinet: Double Doors Cabinets from Scratch
Kitchen Upper Cabinet: Double Doors by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage,
More informationpholstered Vanity Seat
U pholstered Vanity Seat For years I sat on an extremely uncomfortable chair to apply my makeup. I finally replaced it with this sturdy seat that is both attractive and comfortable. This finished size
More informationSafety First! Use eye protection, always! Use ear protection with loud power tools. Stay with children while they work!
TM TM ART TABLE Safety First! Use eye protection, always! Use ear protection with loud power tools Stay with children while they work! Follow tool manufacturers safety guidelines Page 1 ART TABLE Page
More informationDesigned for Vectric by Michael Tyler
Project Tutorial Compatible with: (or greater) and (or greater) Sample Carved with: ShopBot Buddy PRSalpha BT48 www.shopbottools.com Featuring compatibility with nearly all CNC Machines Decorative Grocery
More informationCurved Metal Segmenting
Curved Metal Segmenting A Tutorial by: David Washburn A.K.A djwood1 This tutorial was downloaded from The International Association of Penturners Introduction As I continue to learn about pen turning,
More informationSyracuse University Library Department of Preservation and Conservation Manuals. Drop Spine Box
Drop Spine Box The "drop spine" box is a more rigid enclosure than the phase box. It is designed to protect vellum and significant bindings from wear, light and rapid environmental changes. All measurements
More informationPoorBoy Skiff. A 10-11ft 6in skiff for outboard motoring By Steven Lewis
PoorBoy Skiff. A 10-11ft 6in skiff for outboard motoring By Steven Lewis PoorBoy is about the simplest small motorboat you will come across. It consists of 2-2 1/4 sheets of plywood (1-1 1/4 sheets x3/8
More information15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
More informationWindsor Chair Online. Assembly Instructions
Windsor Chair Online Assembly Instructions Date: 1/4/2007 Other Chairs Offered Philadelphia Arm Chair New England Comb Back Sackback d Arm Chair Bow Back Side Chair Fan Back Side Chair Page 1 Table of
More informationDonaldson s Department Store
Donaldson s Department Store Instructions for Assembly of Donaldson s Department Store Kit Contents: 80 each laser cut acrylic parts. 1 each sheet of canopy parts. 1 each sheet of AC roof unit parts. 1
More informationPinewood Derby Display Case
Pinewood Derby Display Case Optional Door Design by Neil Fern - Pack 187 Exterior Dimensions 23 ½ (H) X 10 ½ (W) X 3 ½ (D) Front Back OPTIONAL Door Finished Interior Dimensions 21 7/8 (H) X 9 (W) X 3 (D)
More informationF100 Super Sabre instructions.
F100 Super Sabre instructions. The F100 is a Jet model for the Wemotec 480 Minifan. Start with taking the parts out of the sheet and sand of the connection tabs. Instructions RBCkits F100 Super Sabre 1
More informationThis article was written by Phill Brander (AUS), who has built many timber catamarans including a Paper Tiger.
Building a Paper Tiger Catamaran Scarfing Plywood Paper Tiger Catamaran GUIDES Warnings/Cautions As always, using any power tools, cutting implements or adhesives carries certain risks. Make sure you understand
More information1Take the keel (3) and
1 The hull and the bridge 1Take the keel (3) and apply PVA wood glue in the second slot from the left: a toothpick may make it easier. Take care: the left end is the one that has a projection. THE HULL
More informationBasic Instructions. Preparing the Moulds
Preparing the Moulds Basic Instructions 1. Make sure the moulds are clean and free of plaster residue (see our CARE & CLEANING instructions for more information). 2. Rinse the moulds in warm water and
More informationShoe Organizer Plans Our Home from Scratch
Shoe Organizer Plans by Our Home from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, injury or death
More informationRobert Bosch GmbH. Minimalist washstand
Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to
More informationTape Measure Metal Clippers Screw Bit Set With Extensions
IMPORTANT: Read through instructions thoroughly before beginning to replace any damaged material. Minor damage can be fixed with a fiberglass repair kit and color matched paint. Tools Required Tape Measure
More informationBeds may be put up or taken down quickly by use of a simple bolted connection at rails and uprights. MATERIALS LIST
CANPLY This design has been made both functional and attractive by use of pattern cut-outs in head and foot uprights, which serve as ladders. Since most children love to climb, getting them to bed will
More informationA Magazine Rack with a Top
A Magazine Rack with a Top Introduction: I have never come across a good free plan for a magazine rack. Yet almost all homes have one. So this is one of the few items I have made on my own, as I don t
More informationHARRISON S HARDWARE PF5891
1:48 BUILDING KIT HARRISON S HARDWARE PF5891 Model the local hardware store where layout residents can find all they need to keep their homes in tip-top shape and workshops running smooth. The positive
More informationTools: Drill/Driver Kreg Jig Miter Saw Jigsaw Circular Saw Adjustable Square Tape Measure Veneer Trimmer Sandpaper and Sander
R PROJECT PLANS DROP-FRONT DESK Create a workspace almost anywhere with this drop-front desk. Mounted to a wall, it doesn t take up any floor space, which means you can hang it wherever you need to work.
More informationModel the hub of your layout s rural setting. Planters Feed and Seed Supply Instructions N Scale 1:160 WOODLAND SCENICS
PF5201 Planters Feed and Seed Supply Instructions N Scale 1:10 Model the hub of your layout s rural setting. Planters Feed and Seed Supply presents a vintage agricultural center where farmers and rural
More informationNational 5 Practical Woodwork
Exercise C. The legs of a chair are turned on the wood lathe. (a) (i) Sketch and name the tool used to produce the square shoulder shown at A. Name of tool: Sketch and name the tool used to check the diameter
More informationCoat Rack. Materials: Directions:
Coat Rack 2x2 wooden poplar (foundation of the rack) 3/4 inch diameter wood dowels (5-8 depending on how many arms you want) 1/4 inch dowel screw 1/4 inch drill bit Power drill Ruler Pencil Paint/spray
More informationExtendable Large Dovetail Jig
Extendable Large Dovetail Jig Instruction Manual Part # 3458 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools.
More informationStorage Stairs for a Bunk or Loft Bed [1]
[1] Submitted by agarrigan [2] on Fri, 2013-05-24 14:08 [1] Page 1 of 13 About a year ago, when we built a modified version of Ana's Loft bed for our Boys room, we knew a ladder was out of the question
More informationGreg s Right Size Big Band Risers
Greg s Right Size Big Band Risers Based on a 32 inch square module 3/4 plywood lids with interlocking tabs on five gallon buckets February 25, 2012 Yes, it looks better with black paint and black buckets.
More informationMaking a snap lid box By Jeffrey A Lavine
Making a snap lid box By Jeffrey A Lavine Some call them boxes, some call them lidded bowls, others call them vessels or containers but whatever you call them they are both enjoyable and a challenge to
More informationUser Guide: Setting Up and Using Rail & Stile Sets
User Guide: Setting Up and Using Rail & Stile Sets Table of Contents Important Safety Information... 3 Prepare the Project Wood and Size Work Pieces... 4 Make Test Cuts and Setup Blocks before Cutting
More informationAdjustable Box Joint Jig. Richard Hicks on 8/24/2015. Box or Finger Joints
Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box or Finger Joints Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box Joints are also called Finger Joints Because they have interlocking fingers
More informationMILL LANE SIDINGS MLS052 Stock Storage Cassette System Kit For Peco Code 80 Flexible Track (not included)
Parts MILL LAN SIINS MLS052 Stock Storage Cassette System Kit or Peco Code 80 lexible Track (not included) A x1 x2 C x1 x6 x2 x1 x1 Parts and are only required to join two cassettes into one luing The
More informationIndustrial Contractors Supplies, Inc.
Industrial Contractors Supplies, Inc. - Dust Director Division - 15061 Route 30, N. Huntingdon, PA 15642 Phone: 412. 824. 6933 Fax: 412. 824. 4704 www.dustdirector.com 5" & 7" SURFACE DUST GUARDS MANUAL
More informationNoville School Diorama Part 4 Making the Floors and Plastering the Walls and Ceilings
Noville School Diorama Part 4 Making the Floors and Plastering the Walls and Ceilings Moulds and Materials Making the Floors Plastering the Ceiling Plastering the Walls Installing the Ceiling and Floor
More informationConstruction Guide for Quick Build F-22 Raptor Design by Tomas Hellberg
Construction Guide for Quick Build F-22 Raptor Design by Tomas Hellberg This kit is very simple to put together. The biggest danger in messing up this kit is gluing the pieces to your work bench. But before
More informationCO 2 DRAGSTER DESIGN AND CONSTRUCTION Notes for Students
CO 2 DRAGSTER DESIGN AND CONSTRUCTION Notes for Students EXAMPLES OF DRAGSTER SHAPES AND STYLES 1. Shell Cars the wheels hidden inside the body 2. Rail Cars the wheels outside the body 3. Shell Reveal
More informationDAVENPORT DEPARTMENT STORE PF5214
1:160 BUILDING KIT DAVENPORT DEPARTMENT STORE PF5214 Dress up your downtown scene with the classic Victorian architecture and large first-floor picture windows of the Davenport Department Store. Details
More informationHOW TO INSTALL ELITE PANELED WAINSCOTING Using X-Rails with Either Raised, Flat or Beaded Panels
HOW TO INSTALL ELITE PANELED WAINSCOTING Using X-Rails with Either Raised, Flat or Beaded Panels 1. First, remove the cover plates from all electrical outlets. All baseboards should also be removed; the
More informationPivot-Door Downdraft Cabinet Plans
Pivot-Door Downdraft Cabinet Plans Finished Cabinet Closed Open Exploded View Introduction This simple downdraft-style dust collection cabinet is a great way to keep your shop cleaner and keep your router
More informationCARVE A HUMMINGBIRD PIN/MAGNET By Donna LaChance Menke
1 CARVE A HUMMINGBIRD PIN/MAGNET By Donna LaChance Menke These little hummers have been a favorite of my students for many years. It was the first pattern I developed and the first class I taught back
More informationMake your own zero clearance throat plate.
Make your own zero clearance throat plate. A picture tutorial By Wayne Breshears One of the more important table saw accessories you can have is a zero clearance insert or throat plate. The close tolerance
More informationTransfer an Image to Drawing Paper
Level: Beginner to Advanced Flesch-Kincaid Grade Level: 8.4 Flesch-Kincaid Reading Ease: 64.6 Drawspace Curriculum 1.2.A5 6 Pages and 4 Illustrations Transfer an Image to Drawing Paper A three-step process
More information