Stenoboard Assembly Instructions Full kit with assembled electronics Step 1 - Check that nothing is missing
|
|
- Emery Weaver
- 5 years ago
- Views:
Transcription
1 Stenoboard Assembly Instructions Full kit with assembled electronics Step 1 - Check that nothing is missing Parts: 1x Left frame 1x Right frame x Consonants keys x Vowels keys x Number keys 4x Pre-assembled PCBs 1x Arduino Leonardo 1x White alarm cable 13x Male to Female header cable 3x Female to Female header cable 3x Modified Female to Female header cable 0x Self-threading screws (,9mm x 13mm) 4x Self-threading screws (,9mm x 9mm) 3x Self-threading screws (,9mm x 6mm) 1x Anti-slip pad
2 Step Connect Main Right PCB to Arduino Parts: Main Right PCB Arduino 13x Male to Female header cables To do: If you place the Main Right PCB in front of you, you can see a 13 pins headers on the top right. Pins are enumerated from 0 to 1, starting from the left. Connect Arduino to the Main Right PCB according to the following table: Arduino pin Main Right pin GND Warning: failing to correctly connect the PCBs according to the previous table may result in permanent damage to Arduino.
3 Step 3 Connect Main Left PCB to Left Vowels PCB Parts: Main Left PCB Left Vowels PCB 3x Female to Female header cables To do: If you place the Main Left PCB in front of you, you can see a 3 pins headers on the bottom right. Pins are enumerated from 0 to, starting from the left. Similarly, on the Left Vowels PCB, you can see a 3 pins headers on the top, and pins are enumerated from 0 to, starting from the left. Connect the Main Left PCB to the Left Vowels PCB according to the following table: Main Left pin Left Vowels pin Warning: failing to correctly connect the PCBs according to the previous table may result in permanent damage to Arduino.
4 Step 4 Assemble Right Frame Parts: Electronics connected in Step 1x Right Vowels keys 1x Right Vowels PCB Right Frame 3x Modified Female to Female header cable 3x Self-threading screws (,9mm x 6mm) x Self-threading screws (,9mm x 9mm) 6x Self-threading screws (,9mm x 13mm) To do: Place Arduino on the bottom of the Right Frame and tighten the 6mm screws. IMPORTANT: DO NOT tighten them too much but very lightly or the screws will strip the holes; please follow this advice for all screws in this and subsequent steps. If you do strip any hole, you can put a dab of glue inside the hole before tightening the screw.
5 Place the Right Vowels PCB in the Right Frame and tighten the 9mm screws. Do the same for the Main Right PCB with 4x 13mm screws.
6
7 Place the Vowels keys in the frame and tighten the x 13mm screws.
8 Connect the Vowels PCB to the Main Right PCB according to the following table: Main Right pin Right Vowels pin
9 Warning: failing to correctly connect the PCBs according to the previous table may result in permanent damage to Arduino. Step 5 Assemble Left Frame Parts: Electronics connected in Step 3 1x Left Vowels keys Left Frame x Self-threading screws (,9mm x 9mm) 6x Self-threading screws (,9mm x 13mm) To do: Place the Left Vowels PCB in the Left Frame and tighten the 9mm screws. Do the same for the Main Left PCB with 4x 13mm screws.
10 Place the Vowels keys in the frame and tighten x 13mm screws.
11 Step 6 Final assembly Parts: Frames assembled in Step 4 and Step 5 x Consonants keys x Number keys 1x White Alarm cable 8x Self-threading screws (,9mm x 13mm) To do: If you place the Main Left PCB in front of you, you can see a 11 pins headers on the top right. Pins are enumerated from 0 to 10, starting from the left. Similarly, on the Main Right PCB, you can see a 11 pins headers on the top left, and pins are enumerated from 0 to 10, starting from the left. Connect the two PCBs with the white alarm cable according to the following table: Main Left pin Main Right pin
12 Warning: failing to correctly connect the PCBs according to the previous table may result in permanent damage to Arduino. Place the Consonants keys and Number keys on top of the left frame and tighten the screws. Do the same for right frame. Make sure that wires and cables do not touch the keys above them, otherwise some of the keys may require more force to trigger them.
13
14 Congratulations! You now have an assembled Stenoboard and can connect it to your PC. Don't forget to install the Arduino IDE before connecting Stenoboard: If you don't, Stenoboard may only work in NKRO-emulation mode and it may not be possible to update the firmware in the future. If that happens to you, you can fix it by restoring your computer to a previous restore point.
ScaleRCHelis.com V Light Controller Kit
Thank you for purchasing the ScaleRCHelis.com V1.1 450 Light Controller Kit. This is something you can build in under a hour with some simple soldering equipment. Your kit will include all the parts necessary
More informationFM125 & FM126 Service Guide
FM125 & FM126 Service Guide FM125-0022 & FM125-0024 Repair Kit 1 2 3 4 #1-1 Pc. FM125-5012 Ball Carrier Installation Tool (FM125-0022 Only) #2-2 Pcs. P5-287-R0 O-Ring #3-2 Pcs. P5-067-R2 O-Ring #4-1 Pc.
More informationAAG CloudWatcher Update Humidity sensor (*)
AAG CloudWatcher Update Humidity sensor (*) (*) For AAG CloudWatcher units SN 400 onwards. For a better understanding of these instructions we have divided them into two sections: to units with serial
More informationLITTLE NERD v1.1 Assembly Guide
last update: 9. 3. 2016 LITTLE NERD v1.1 Assembly Guide bastl instruments.com INTRODUCTION This guide is for building Little Nerd module from Bastl Instruments. It is good to have basic soldering skills
More informationCongratulations on your purchase of the SparkFun Arduino ProtoShield Kit!
Congratulations on your purchase of the SparkFun Arduino ProtoShield Kit! Well, now what? The focus of this guide is to aid you in turning that box of parts in front of you into a fully functional prototyping
More informationAssembly notes for RFX Teensy 3.x carrier board
Assembly notes for RFX Teensy 3.x carrier board Mark Pendrith , Dec 2014. Basic kit parts (BOM) 1 PCB mount 5mm/2.1mm DC barrel jack (see note below) 1 LD1117v33 1 1N5817
More informationThe ability to make basic voltage and resistance measurements using a digital multimeter
Congratulations on your purchase of a new OneShot chassis! The PC01 OneShot combines a rugged enclosure, power supply, and discrete instrument DI in a compact 1/4U package. A few minutes of assembly are
More informationABC V1.0 ASSEMBLY IMPORTANT!
ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through
More informationBombiniBot Parts and Assembly
BombiniBot Parts and Assembly Copyright 05 mindsensors.com / Parts Loose Parts: Part Quantity Tire Motor Mount 4-Wire Encoder Cable Encoder Wheel Velcro Strip Top Chasis Plate Bottom Chasis Plate Battery
More informationLesson 2: Soldering. Goals
Introduction: Its time to learn how to solder. So you have met all the components needed to make a DIY Gamer, now it s time to put it together. Soldering is joining the components to the printed circuit
More informationSkill Level: Beginner
Page 1 of 9 RFM22 Shield Landing Page Skill Level: Beginner Overview: The RFM22 shield is an Arduino-compatible shield which provides a means to communicate with the HOPERF RFM22 radio transceiver module.
More informationPenrose Quantizer Assembly Guide
Penrose Quantizer Assembly Guide Schematic and BOM The schematic can be found here: www.sonic-potions.com/public/penrosequantizerschematic.pdf The BOM is available at google docs: Link to BOM Prepare the
More informationMICROGRANNY v2.1 - Assembly Guide
last update: 9. 5. 2017 MICROGRANNY v2.1 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the MicroGranny kit. MicroGranny is a monophonic granular sampler by Bastl
More informationDouble Screen Door Installation Instructions
Double Screen Door Installation Instructions (36) #8x1 tek screws (20) #8x1/2 tek screws Package Includes: (2) PCA Screen Doors (1) Astragal (1) Left Hand Z-bar (1) Right Hand Z-bar (1) Header Z-bar (2)
More informationMULTI-ACTIVITY PLAY TABLE
ASSEMBLY INSTRUCTIONS! WARNING: CHOKING HAZARD - Small parts. Not for children under 3 years.! CAUTION: Adult assembly required. C 2006 Melissa and Doug, Inc. All Rights Reserved www.melissaanddoug.com
More informationDual Band Filter Assembly Manual
Dual Band Filter Assembly Manual 12 January 2018 Rev D Version Theory of Operation: The purpose of a Bandpass Filter is to filter out or reject all unwanted signals. The original KN-Q7A Receive Filter
More informationLine Following Circuit Board Wiring Guide
Line Following Circuit Board Wiring Guide Soldering the Analog Optosensors 1. Obtain a line following printed circuit board from the store as well as three analog optosensors (w/6 resistors). 2. Remove
More informationLesson 2: Soldering. Goals
Introduction: Its time to learn how to solder. So you have met all the components needed to make a DIY Gamer, now it s time to put it together. Soldering is joining the components to the printed circuit
More information0Introduction. TECHNICAL DOCUMENTATION 20/02/2009 PRESSURE Brake pressure PSI
TECHNICAL DOCUMENTATION 20/02/2009 PRESSURE Brake pressure Notes: technical documentation, dimensions and pinout of brake pressure sensors sensors 0-2000 PSI Release 1.01 0-2000 PSI 0Introduction 0-2000
More informationThis guide contains everything you need to set up and operate all three. Inspira Imperial Quilting Frame Assembly...2
Congratulations on the purchase of your Husqvarna Viking Mega Quilter 18x8, Inspira Imperial Quilting Frame, and QBOT by Inspira! This guide contains everything you need to set up and operate all three.
More informationV4 Premium Kit. Prusa i3 Build Guide
V4 Premium Kit Prusa i3 Build Guide Hi! Congratulations on your purchase of the DIYElectronics.co.za Prusa I3 kit, the best South African 3D Printer Kit! Hopefully this should serve as complete guide to
More informationArducopter 3DR-B Hardware
Arducopter 3DR-B Thank you for purchasing an Arducopter 3DR kit. The Arducopter 3DR is a stable and supported quadrotor frame in the ongoing development of the Arducopter code on DIYDrones. It features
More informationEA6500 Antenna Installation Instructions:
Thank you for purchasing the 6 Antenna Mod Kit for your Linksys router. First we will show you how to install the antennas for your router. Next we will teach you how to setup the DD-WRT firmware which
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationASSEMBLY GUIDE. Mia Narrow Bookcase
ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step
More informationAdafruit 16-Channel Servo Driver with Arduino
Adafruit 16-Channel Servo Driver with Arduino Created by Bill Earl Last updated on 2015-09-29 06:19:37 PM EDT Guide Contents Guide Contents Overview Assembly Install the Servo Headers Solder all pins Add
More informationWarm Tube Clock. Before we start, please make sure that you have all required parts that come for the IN-16 Nixie shield :
Warm Tube Clock Assembly Instructions for the IN-16 Nixie shield Introduction Congratulations on your purchase of OSH Nixie Tube Clock. In this document you will see all steps you need to follow in order
More informationAluminum and Steel Machined Flaperon Handle for Belite Aircraft ASSEMBLY INSTRUCTIONS. Last Revised January 7, 2016
Aluminum and Steel Machined Flaperon Handle for Belite Aircraft ASSEMBLY INSTRUCTIONS Last Revised January 7, 2016 Read and understand all instructions completely before beginning your Flaperon Handle
More informationCircuit Board Assembly Instructions for Babuinobot 1.0
Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming
More informationInstallation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions)
Installation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions) This tutorial is designed to aid you in installation of a console customs
More informationConstruction Guide European Version
Construction Guide European Version PCB This section describes how to build up the DRO-350 printed circuit board (PCB). The bare PCB is available for purchase on the order page. Static Protection Bare
More informationBliptronome! Wil Lindsay
Bliptronome! Bliptronic 5000 to Monome Clone Conversion Build Instructions (version 3 ) Wil Lindsay www.straytechnologies.com wil@straytechnologies.com Building and Modding: This kit was created as a synthesis
More informationUSER MANUAL. MODEL 2017A RS-232 to 20ma Current Loop Converter. SALES OFFICE (301) TECHNICAL SUPPORT (301)
USER MANUAL MODEL 2017A RS-232 to 20ma Current Loop Converter Part# 07M2017A-A Doc# 073021UA Revised 10/15/93 SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com 1.0 WARRANTY
More informationTIMESQUARE Wordclock. Created by Andy Doro. Last updated on :51:57 PM UTC
TIMESQUARE Wordclock Created by Andy Doro Last updated on 2018-08-22 03:51:57 PM UTC Guide Contents Guide Contents Overview Create Faceplate Laser cutting 3D printing Uploading Code Marquee Binary Moon
More informationFlexRC Mini Owl - Extreme FPV Proximity Racing Drone - DIY Build Instructions
FlexRC Mini Owl - Extreme FPV Proximity Racing Drone - DIY Build Instructions This guide will walk you through the detailed build steps using the FlexRC Mini Owl Extreme FPV Racing Drone DIY Kit. The kit
More informationZIERICK MANUFACTURING CORPORATION
ZIERICK MANUFACTURING CORPORATION 131 Radio Circle, Mount Kisco, New York 10549 - (914) 666-2911 - FAX (914) 666-0216 Engineered Interconnection Solutions -Since 1919-3/8-16 THREAD Zierick Printed Circuit
More informationIR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015
IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 1 2 For the main circuits of the line following robot you soldered electronic components on a printed circuit board (PCB). The
More informationBGA Adapter-CSPACK/CSICE. Instruction for use
BGA Adapter-CSPACK/CSICE Instruction for use (1) Soldering CSPACK on a target board: 4 non-through holes for guide pins have to be provided on a target board for positioning CSPACK precisely on soldering
More information4ms SCM Breakout. Kit Builder's Guide for PCB v2.1 4mspedals.com
4ms SCM Breakout Kit Builder's Guide for PCB v2.1 4mspedals.com Shuffling Clock Multiplier Breakout This guide is for building a Shuffling Clock Multiplier Breakout module (SCMBO) version 2.1 from the
More informationRIPPER PEDAL. Bearing / Axle Replacement. ( Disassembly )
RIPPER PEDAL Bearing / Axle Replacement ( Disassembly ) 1 1. Use good quality tools to avoid stripping screw sockets. 2. When servicing your pedals, work on one side at a time to prevent parts from mixing
More informationBIFOLD FUTON FRAME TRINITY ARM. Seat Rails and Slats x 1. *Note: Use 4pc of 100mm Bolts and 4pc of 60mm Bolts to attach the arms to the Stretchers.
1A Parts in this box. 2pc with extra holes 2pc with extra holes & plastic stoppers Arms x 2 Back Rails and Slats x 1 Full Size: Slat Supports x 6 3pc are longer for the Back deck Back Side Rails x 2 Seat
More informationSunday, November 4, The LadyUno Sound Unit
The LadyUno Sound Unit Here s what we ll need for this project We start with our finished Lady Ada Wav Shield. 5V for LCD Serial Data for LCD GND for LCD 5V (coming from the BBB) is_lady_ada_busy PIN GND
More informationPololu DRV8835 Dual Motor Driver Kit for Raspberry Pi B+
Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi B+ Pololu DRV8835 dual motor driver board for Raspberry Pi B+, top view with dimensions. Overview This motor driver kit and its corresponding Python
More informationNEX-2X-PROBE. Back to back mounting hardware for use with the Tektronix P6860/80/64 or P6419 Probes
NEX-2X-PROBE Back to back mounting hardware for use with the Tektronix P6860/80/64 or P6419 Probes Reduces by 50% the circuit board area needed to probe 34 channels Uses only two retaining holes to hold
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationS&T GeoTronics LLC Open DSKY with AGC Assembly Instructions
S&T GeoTronics LLC Open DSKY with AGC Assembly Instructions First, make sure you have all the required components: HARDWARE Qty Item 1 DSKY PCB v1.0d 1 Arduino Nano 1 VA RTC 1 IMU 1 Buck StepDown 1 SKM53
More informationivu Series TG Image Sensor
Quick Start Guide Introduction The ivu Series Image Sensor is used to monitor labels, parts, and packaging for type, size, orientation, shape, and location. The sensor has an integrated color touch screen
More informationEGG 101L INTRODUCTION TO ENGINEERING EXPERIENCE
EGG 101L INTRODUCTION TO ENGINEERING EXPERIENCE LABORATORY 6: INTRODUCTION TO BREADBOARDS DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING UNIVERSITY OF NEVADA, LAS VEGAS GOAL: This section introduces
More informationAdjustable Hammered Dulcimer Stand
Adjustable Hammered Dulcimer Stand Musicmaker s Kits (Hwy 36 behind Joseph s Restaurant) P.O. Box 2117 Stillwater MN 55082 651 439 9120 www.harpkit.com PARTS LIST: 1 Set of Assembly Instructions A. 2 front
More informationMAKEBLOCK MUSIC ROBOT KIT V2.0
MAKEBLOCK MUSIC ROBOT KIT V2.0 Catalog Music Robot Kit V2.0 Introduction... 1 1 What is Music Robot Kit V2.0?... 1 1.1 Mechanical part... 1 1.2 Electronic part... 1 1.3 Software part... 1 2 Music Robot
More informationPAPER SHREDDER MERCURY RDS2050,RDX1750,RDS2270,RDX1970 ILLUSTRATED PARTS LIST
PAPER SHREDDER MERCURY RDS2050,RDX1750,RDS2270,RDX1970 ILLUSTRATED PARTS LIST Acco Service Division, Halesowen Industrial Estate, Hereward Rise, Halesowen, West Midlands B62 8AN Telephone 0845 658 6600
More informationQRPme Crystal Checker Kit Featured in FDIM 2011 Build-Along
QRPme Crystal Checker Kit Featured in FDIM 2011 Build-Along This crystal checker circuit was first presented in a workshop given by WA3OPY, AC5UR & W1REX a few years ago at the 4 States QRP Club gathering
More informationQRPGuys Iambic Mini Paddle w/base
QRPGuys Iambic Mini Paddle w/base First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationPacific Antenna RF Probe assembly
Pacific Antenna RF Probe assembly Parts In the Kit: 1 1/2 x 3 Blue PEX tube 2 5/8 O.D. vinyl caps 2 3/32 dia x 2 brass tube sections 2 Pogo spring contacts 1 4-40 x 7/16 pan head screw 1 4-40 x 1/4 pan
More informationAdafruit 16-channel PWM/Servo Shield
Adafruit 16-channel PWM/Servo Shield Created by lady ada Last updated on 2018-08-22 03:36:11 PM UTC Guide Contents Guide Contents Overview Assembly Shield Connections Pins Used Connecting other I2C devices
More informationXSpc. Contents. Page 3-4. Component list. Preparing the back panel
H Cube+ Contents Component list Page - 4 Accessories Page 5-6 Preparing the base panel Page 7 Preparing the back panel Page 8 Preparing the front panel Page 9 Attaching the back panel Page 0 Attaching
More informationInstructions. Perspex CubeSat Kit
A Instructions Thank you for purchasing the Perspex CubeSat Kit (pcsk). This kit is a model of a Pumpkin, Inc. 1U skeletonised CubeSat Kit and is typically used for modeling or mounting CubeSat electronics
More informationGT3B Hack Kit Install Instructions Written By Austin Hutchison
GT3B Hack Kit Install Instructions Written By Austin Hutchison Step 1: Remove 4 screws located on top of the radio. 1 Step 2: There are small plastic latches that also hold the top in place. The easiest
More informationTD-1 Tone Decoder / Trigger Version 1.0
TD-1 Tone Decoder / Trigger Version 1.0 Document Version: 1.00 01 MAR 2013 Copyright 2013 EFX-TEK DESCRIPTION The TD-1 is a member of EFX-TEK's family of amigo boards: user-friendly, plug-and-play solutions
More informationAgave Standard Series
Mailing Address: 033 San Elijo Ave, #464 Cardiff, CA 9007 619.708.917 619.330.88 fax info@agaveiron.com www.agaveiron.com Agave Standard Series Flat Track Hardware Systems General Information and Installation
More informationMounting description. AQUACOMET Kft. Internet:
Mounting description AQUACOMET Kft. Internet: www.aquacomet.hu E-mail: info@aquacomet.hu Tel/Fax: (+36 96) 314301, 517417, 328971 Mobil: (+36 30) 2046 801, 9578 470 I. Mounting of the rails 1. Measure
More informationLED RETROFIT INSTALLATION
QUICK INSTRUCTIONS 1 2 3 4 5 6 Once the original fixture components have been removed to satisfy rebate requirements the Raffino LR Series retrofit kit is ready to be instal. At a minimum the original
More informationProduct Information ECI 1319S EQI 1331S. Absolute Rotary Encoders without Integral Bearing and with DRIVE-CLiQ Interface.
Product Information ECI 1319S EQI 1331S Absolute Rotary Encoders without Integral Bearing and with DRIVE-CLiQ Interface Firmware 15 12/2018 ECI 1319S, EQI 1331S Rotary encoders for absolute position values
More informationBUILD AND DRIVE THE RADIO-CONTROLLED MODEL SCALE 1:16
BUILD AND DRIVE THE RADIO-CONTROLLED MODEL 7 SCALE 1:16 CONTENTS STAGE PAGE 34 The fourth stowage pannier 81 35 The gun, mantlet cover and track 83 36 The recoil mechanism 85 37 The infrared receiver 87
More informationivu Plus Quick Start Guide P/N rev. A -- 10/8/2010
P/N 154721 rev. A -- 10/8/2010 Contents Contents 1 Introduction...3 2 ivu Plus Major Features...4 2.1 Demo Mode...4 2.2 Sensor Types...4 2.2.1 Selecting a Sensor Type...5 2.3 Multiple Inspections...6 2.3.1
More informationBill of Materials: PWM Stepper Motor Driver PART NO
PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,
More informationSOLDERING TESTER TM-200. Thank you for buying Soldering Tester TM-200. Please read this Owner's Operation Manual before using your soldering tester.
OPERATION MANUAL SOLDERING TESTER TM-200 WARNING Read this Owner's Operation Manual before using your soldering tester. Failure to follow the warning and instructions in this manual could result in serious
More informationVSD-6500 Frame Exploded View LIFT P/N
VSD-6500 Frame Exploded View LIFT P/N 511-65075-01 34 34 45 96 55 108 22 9 7 55 54 34 89 90 56 24 99 23 111 SEE SHEET 4 34 91 45 106 20 55 26 68 95 5 55 109 7 22 8 54 53 71 66 5 95 31 58 6 6 46 60 73 25
More informationBrewsBySmith.com STC DIY Kit
BrewsBySmith.com STC-1000 + DIY Kit Contact Information: Greg Smith www.brewsbysmith.com greg@boostbysmith.com I. Hardware Included: STC-1000 flashed with latest software (v1.06 currently) (if purchased)
More informationTechnical Newsletter #tnl e # 1 / 23
# 1 / 23 Change of the carbon brush replacement procedure in DAD3350 Maintenance Manual Purpose of this document There were cases where the replacement operation of the carbon brush was not correctly performed,
More informationMP573 Assembly guide. Soldering. MP573 Assembly guide PCB split PCB split. Document revision 2.2 Last modification : 22/08/17
MP573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationPro-Doweling Kit USER S MANUAL #840. Visit us at
Pro-Doweling Kit USER S MANUAL #840 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Please read this manual carefully and thoroughly
More informationKeypad Lock Retrofit Kit for Follett REF Undercounter Refrigerator P/N
Materials supplied Reference # Keypad assembly (housing and mounting base) 1 Keypad housing base 2 Lock mechanism with cable 3 (9) 8-32 x 1/2" stainless steel screws 4 Latch 5 Jig 2, latch 6 Jig 1, keypad
More informationQ960 Sequential Controller
The Q960 Sequential Controller is a recreation of Bob Moog's famous 960 module. Built using modern components yet retaining the 960's unique functionality including the highly sought-after skip function,
More informationGeeetech A30 3D Printer Building Instruction
Geeetech A30 3D Printer Building Instruction Contents Safety Instructions... 1 Preparation... 2 1. Unfold the Box and Check the Package... 3 2. Assembly... 4 3. Wiring... 9 4. Warm Tips...16 Safety Instructions
More informationArdweeny 1.60" 0.54" Simple construction - only 7 parts plus pins & PCB! Ideal for breadboard applications
Ardweeny tm Arduino -compatible Microcontroller Like to build your own breadboard-compatible Arduino? Get all the basic features of Arduino in a tidy, cost-effectve package! Build Time: 20mins Skill Level:
More informationRB-Pol-116 Pololu D24V6ALV Step-Down Voltage Regulator Overview
RB-Pol-116 Pololu D24V6ALV Step-Down Voltage Regulator Overview These adjustable buck (step-down) voltage regulators from Pololu generate lower, user-adjustable output voltages from a wide input voltage
More informationMGL Avionics Autopilot. Servo. Specifications & Installation Manual. Last Update: 20 October Disclaimer:
MGL Avionics Autopilot Servo Specifications & Installation Manual Last Update: 20 October 2010 Disclaimer: MGL Avionics should not be held responsible for errors or omissions in this document. Usage of
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Antenna diagram showing configuration and lengths when assembled 7 8 16 9 16 9 Description The Pacific Antenna lightweight dual band dipole kit provides
More informationRepair Instructions grand MA
Repair Instructions grand MA Grand MA 1 Repair Instructions grand MA The following tasks may be performed by qualified personnel only! By disregarding the instructions or the prescribed sequence of tasks
More informationMotorola E815 / E816 Disassembly / Assembly Guide. Ver. 1.1 By Chubbs_WA
Motorola E815 / E816 Disassembly / Assembly Guide Ver. 1.1 By Chubbs_WA April 10, 2007 Table of Contents Disassembly Tools needed 3 Disassembly for dummies 4 Just a note 5 Disassembly of keypad housing
More informationPacific Antenna 20 and 40M Lightweight Dipole Kit
Pacific Antenna 20 and 40M Lightweight Dipole Kit Diagram showing configuration and approximate lengths 8 6 16 9 16 9 8 6 Description The Pacific Antenna lightweight dual band, trap dipole kit provides
More informationRepairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip
Repairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip Disassembly, repair and reassembly of Wedge Touch mouse when the battery cover will not stay closed. Also is a good guide to repair other
More information4. Z-axis assembly. 4. Z-axis assembly. Written By: Josef Prusa manual.prusa3d.com Page 1 of 18
4. Z-axis assembly Written By: Josef Prusa 2017 manual.prusa3d.com Page 1 of 18 Step 1 Get the necessary tools 13/17mm spanners 3.6mm flathead screwdriver Needle-nose pliers 2.5 and 1.5mm Allen key Step
More informationAdafruit 16-channel PWM/Servo Shield
Adafruit 16-channel PWM/Servo Shield Created by lady ada Last updated on 2017-06-29 07:25:45 PM UTC Guide Contents Guide Contents Overview Assembly Shield Connections Pins Used Connecting other I2C devices
More informationLine-Following Robot
1 Line-Following Robot Printed Circuit Board Assembly Jeffrey La Favre October 5, 2014 After you have learned to solder, you are ready to start the assembly of your robot. The assembly will be divided
More informationmeped v2 Assembly Manual
meped v Assembly Manual The meped is an open source quadruped robot designed by Scott Pierce of Spierce Technologies, LLC. This design is released under the Creative Commons, By Attribution, Share Alike
More informationAssembly Instructions Beta Prusa Standard & Deluxe
Assembly Instructions Beta Prusa Standard & Deluxe 3D Printer Version 2.6 Date Page 1 / 67 General data about the assembly instructions for an incomplete machine according to appendix VI of the EG machinery
More informationAssembly Instructions. Beta Prusa DualX 3D Printer
Assembly Instructions Beta Prusa DualX 3D Printer Version 2.6 Date Page 1 / 72 General data about the assembly instructions for an incomplete machine according to appendix VI of the EG machinery directive
More informationSB Protoshield v1.0. -Compatible Prototyping & Breadboard Shield Design and build your own interface for your Arduino-compatible microcontroller!
SB Protoshield v1.0 tm Arduino -Compatible Prototyping & Breadboard Shield Design and build your own interface for your Arduino-compatible microcontroller! Build Time: 30mins Skill Level: Beginner (2/5)
More informationAssembling the Heated bed
firepickdelta Assembling the Heated bed Instructions for building the heated bed Written By: Neil Jansen 2017 firepickdelta.dozuki.com Page 1 of 15 Step 1 Exploded View Reference Use the full-size PDF
More informationBINARY. Logic functions for analog computation DIY BUILD GUIDE GRAYSCALE.
BINARY Logic functions for analog computation DIY BUILD GUIDE GRAYSCALE http://grayscale.info BINARY DIY BUILD GUIDE Binary from Grayscale is a 1-bit analog computer for digital logic signals. Patch up
More informationThe Mind Project s Iris 1 Robotic Arm. Packing List Assembly instructions
The Mind Project s Iris 1 Robotic Arm Packing List Assembly instructions Packing list Below you will find pictures and descriptions of each part. It may be helpful to take each piece out of the bag and
More informationRiverside. Windward Bay EntertaInment Wall System Assembly Instructions. Made In Viet Nam. Right Pier. Bridge & Back Panel.
EntertaInment Wall System Page 1 of 12 Product No. 42840 42848 42849 42843 Product Description Console Left Pier Right Pier Bridge & Back Panel Right Pier Bridge & Back Panel Left Pier 63" Inch Ent. Console
More informationScreenLogic Wireless Connection Kit. Installation Guide. pool/spa control system
pool/spa control system ScreenLogic Wireless Connection Kit Installation Guide P/N 520663 - Rev A 8 Technical Support Contact Technical Support at: Sanford, North Carolina (8 A.M. to 5 P.M.) Phone: (800)
More informationDesigned to send specific MIDI information upon each press. Ultra-low current requirement means a single coin cell will last years
PedalSync MIDI Data Module Key Features Discrete MIDI Data delivery in a compact design Designed to send specific MIDI information upon each press Ultra-low current requirement means a single coin cell
More informationThe Mind Project s Iris 1 Robotic Arm. Assembly instructions Step 1
The Mind Project s Iris 1 Robotic Arm Assembly instructions Step 1 Packing list Below you will find pictures and descriptions of each part. It may be helpful to take each piece out of the bag and place
More informationInstallation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna
Release 3.0 NN47251-311 Issue 02.01 June 2014 Installation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna How to get help To access the complete range of services and
More informationCM80 Series Vari-Angle IR Illuminator
CM80 Series Vari-Angle IR Illuminator Installation Guide Rev. 1.1 QIG Part no.: 625040201G Revision History: * Rev. 1.0: Initial Release * Rev. 1.1: Added safety instructions and warning messages. Package
More informationInstallation Guide of Telescope Drive Master Encoder-adapter for Losmandy G11 mount
Installation Guide of Telescope Drive Master Encoder-adapter for Losmandy G11 mount First of all, thank you very much for purchasing our product called Telescope Drive Master and congratulation for your
More information