FMCW Radar Level Transmitter. visit our website

Transcription

1 FMCW Radar Level Transmitter visit our website

2 PRODUCT INTRODUCTION FMCW Radar level transmitter is a non contact measuring device, which is suitable for high temp., high pressure, and corrosive applications. It is easy to install and free of maintenance, especially for the high accuracy requirement environment. PRINCIPLE FMCW radar adopts a high frequency signal, which is emitted via an antenna and swipe frequency increment by 0.5GHz during the measurement, reflected by the target surface and received at a time delay. The frequency difference, which is calculated from the transmitting frequency and the received frequency, which is directly proportional to the measured distance (or material surface). The frequency difference then is processed by Fast Fourier Transformation (FFT) to identify the signal in Intermedium Frequency (IF). This FMCW radar is innate with signal / noise enhancement and filtering of echo-back via Phase-Lock Loop (PLL) circuit that is the best solution for complex environment and high accuracy measurement. FEATURES Non contact measuring Corrosive and toxic liquid, hydrocarbons, slurries Not affected by specific gravity, pressure, temperature, viscosity, foam, and dust Indicate signal wave inside the silo. Selection of Different Measurement unit(m, cm, mm, inch, ft, %, ma) Measuring distance and actual level. Language selection of traditional Chinese, simplified Chinese, English. -0mA/ lead wires Modbus RS-85 to enhance isolation and easy for remote control. CE standards for isolation(eft 000V, B class or better) Suitable for mid-range signal ma, 0mA output Set functions to the continuous measuring device via FAS software. Isolated circuit design. Design formula JFR-00 LINEARITY DIAGRAM Accuracy cm A30mm A0mm A0mm A5mm 0.5m 5m 5m 0m Distance to flange A0.% A0.% A0.% A0.% TEST STANDARDS High voltage : IEC6097- Isolated resistance : IEC Power supply change : IEC Power supply failure : IEC Electrical burst testing : IEC Voltage DIPS : IEC Humidity : IEC High/Low temperature test : IEC & Protection rating IP65 : IEC6059

3 SPECIFICATION f7 f7 f7 Dimensions (Unit:mm) DN00 PN6 FLANGE 8-f8 P.C.D f80 /PF DN00 PN6 FLANGE 8-f8 P.C.D f80 /PF DN00 PN6 FLANGE 8-f8 P.C.D f80 /PF f0 f0 f0 Model Measuring range JFR A 0m(max.30m) JFR B 0m(max.30m) JFR C 0m(max.30m) Accuracy A5mm (m~5m) A0mm (m~5m) A0mm (m~5m) Repeatability A.5mm A5mm A0mm Digital comm. RS85(Isolated) RS85(Isolated) RS85(Isolated) Ambient temp. -0~70BC -0~70BC -0~70BC Operating temp. -0~00BC -0~00BC -0~00BC Operating pressure 0~0 bar 0~0 bar 0~0 bar Frequency Band Band Band Analog output ~0mA/ Wire ~0mA/ Wire ~0mA/ Wire Power consumption Protection rating Min. dielectric constant 00mA/ Vdc IP mA/ Vdc IP mA/ Vdc IP65.5 Power supply VdcA0% VdcA0% VdcA0% Local display Housing material Aluminum Aluminum Aluminum Antenna type Horn Horn Horn Antenna material SUS 30/ 36/ PTFE Coating SUS 30/ 36/ PTFE Coating SUS 30/ 36/ PTFE Coating Sampling rate sec. sec. sec. Blind distance 0.5m 0.5m 0.5m

4 SPECIFICATION f7 f7 /PF 09 /PF 09 Dimensions (Unit:mm) -/" FLANGE -f5 P.C.D f30 f55 -/" FLANGE -f5 P.C.D f30 f55 f 5 f 5 f f Model Measuring range Accuracy Repeatability Digital comm. Ambient temp. Operating temp. Operating pressure Frequency Analog output Power consumption Protection rating Min. dielectric constant Power supply Local display Housing material Antenna type Antenna material Sampling rate Blind distance JFR C 0m A0mm (m~5m) A0mm RS85(Isolated) -0~70BC -0~50BC 0~6 bar Band ~0mA/ Wire 00mA/ Vdc IP65 VdcA0% Aluminum Wave Stick PTFE sec. 0.6m JFR D 0m A30mm (m~5m) A5mm RS85(Isolated) -0~70BC -0~50BC 0~6 bar Band ~0mA/ Wire 00mA/ Vdc IP65 VdcA0% Aluminum Wave Stick PTFE sec. 0.6m 3

5 WIRING/CALIBRATION WIRING INFORMATION CALIBRATION RS85 wiring 5 6 TR- TR+ V+ V- POWER DCV Two ways to calibrate the JFR Series:. With display/adjustment module. By PC based FAS software Adjustment module is an adjustment tool with buttons to click on. It also has a transparent window to allow display reading. RS3/85 Converter Rs3 Interface/ USB Interface JFR Series and Indicator(External Power) 3 V+ V- POWER DCV I+ I- Panel Meter JFR Series and Indicator(Powered by panel meter) [ ] Button -Enter Edit status -Confirm Edit -Confirm parameter modification [ ] Button -Select Edit -Select parameter -Parameter 3 V+ V- I+ I- Panel Meter [ ] Button -Return -Cancel [ ] Button -Increase -Select WIRING DIAGRAM Power Supply: V+ Power Supply: V- Analog Output: I+ (~0mA) Analog Output: I- (~0mA) Communication : TR+ (Rs85) Communication : TR- (RS85)

6 QUICK SETUP FineTek Co. Ltd. FINE-TEK 6.7 M CM MM INCH FT % MA Press + for 3 seconds to enter main menu MAIN MENU SETTING DISPLAY DIAGRAM SERVICE Click on "SETTING MENU." to enter SETTING MENU LOW POINT HIGH POINT BLIND AREA MA RANGE. Click on "LOW POINT.." to enter LOW POINT MM Enter distance between flange and low level by using and. Click on to save and return to. SETTING MENU LOW POINT HIGH POINT BLIND AREA MA RANGE HIGH POINT MM SETTING MENU LOW POINT HIGH POINT BLIND AREA MA RANGE. BLIND AREA MM SETTING MENU LOW POINT HIGH POINT BLIND AREA MA RANGE. Click on "HIGH POINT.." to enter Enter distance between flange and high level by using and Click on to save and return to. Click on "BLIND AREA..5" to enter Enter blind distance counting from flange by using and. Click on to save and return to.. Click on "MA RANGE..6" to enter MA RANGE MM Enter tank heigh, save and go to setting. SETTING MENU LOW POINT HIGH POINT BLIND AREA MA RANGE Press MAIN MENU SETTING DISPLAY DIAGRAM SERVICE DISPLAY MENU. to enter main menu DISPLAY CONTET.. DISTANCE OBJECT HEIGHT PERCENTAGE CURRENT MENU Save and click on to return to.. click on twice to return to the display. FINE-TEK 6.7 M CM MM INCH FT % MA Click on "DISPLAY MENU." to enter. DISPLAY CONTET LCD CONTRAST Click on "DISPLAY CONTENT.." to enter DIAGRAM Measurement bench-mark starts at contact surface of connection. Low level calibration (menu..) High level calibration (menu..) Blind Distance (menu..5) Measuring Distance Setup (menu..6) Note: Be aware of blind distance when measuring material high level.(shown in ) 00% 0% 5

7 SOFTWARE SETUP CALIBRATION Software Setup Calibration(FAS) FAS calibration software can be utilized with JFR Series via RS85/RS3 to allow tank data reading and setup from PC. Parameter Description Low Point: Low point(ma), measuring range from flange to low level. High Point: High point(0ma), measuring range from flange to high level. Blind Area: Blind distance, distance starts from flange surface. Max. Distance: Measuring range between low point nd high point. FAS Operation Instruction. Turn on FAS software. Go to Address, then choose 9600, COM5 from baudrate 3. Click on Connect.. Press "Stop Sync" to change parameter. 5. Press "GetFFT" to read wave reflection diagram. Press "Stop Sync" to change preset parameter. 6

8 INSTALLATION If the JFR-0 is installed on a neck, refer to the limitation on the length and the diameter as below. The horn of the JFR-00 can not hide in the neck. The horn has to expose itself to the tank by 0.39 at least The axis direction of FMCW should be parallel with the wall, or be in orthogonal with the surface. For Install, the distance from the wall should >/3 D, and the height from the surface >/5 H (Measurement Depth) is recommended. 60mm max. (L)5mm D H >/5H Max.</3D 50mm min. Device has to be installed away from the tank wall to avoid disturbance caused by reflection. The turbulent or stirring will make the bubble and vortex that might interface with the measurement, it is recommended to install wave shield tube with vent hole To avoid from this situation. Device has to be installed away from the tank wall to avoid incorrect reflection. vent hole Device is to be installed away from material inlet to avoid disturbance caused by material or other obstacles. A reflector is recommended to be installed when there is disturbing obstacle to avoid false reflection. Please avoid center installation for arched top tanks for possible multiple reflection. Reflector Sun/rain block is recommended for outdoor application. The best installation position for cone shape tank with flat top is at the center spot for full measuring range. 7

9 ORDERING INFORMATION Type Material 0: Horn Antenna Type3 (Length 0mm,opening0mm) Standard : Horn Antenna Type (Length 6mm,opening00mm) : Horn Antenna Type (Length 89mm,opening80mm) 3: Rod Antenna (Length 5mm) Standard : Rod Antenna (Length 55~85mm) Lengthened 0: SUS30---Horn Antenna 6: SUS36---Horn Antenna E: PTFE------Horn Antenna or Wave Rod Antenna with PTEE coating F: PTFE------Rod Antenna Accuracy A: A5mm B: A0mm C: A0mm D: A30mm Connection Size for flange or screw Pressure range or other G: -/"(65A) H: 3" (80A) I: "(00A) J: 5"(5A) K: 6"(50A) S: Others M: 5kg/cm JIS N: 0kg/cm JIS O: 50Lbs ANSI P : 300Lbs ANSI W: PN0 (0Bar) : PN6 (6Bar) Y: PN5 (5Bar) Z: PN0 (0Bar) S: Others Horn Antenna Type3--- "(Min.)(In case of applying in protective tube, the minimum flange size is 6") Wave Rod Antenna --- -/"(Min.) Flange Material Housing Meral 0: SUS30 5: SS zinc coating 6: SUS36 Plastic P: PP E: PTFE R:Aluminum(IP65) JFR- 0 0 R 0 8

10 [FC/FD] [FG] [FF] [FA/FB] [SP] [SF] Mini Float/Magnetic Float Level Switch Magnetic Float Level Transmitter Side Mounting Float Switch Cable Float Level Switch Thermal Dispersion Flow Switch Paddle Flow Switch [EF] [EB] [EA] [EG] [FA/FB] [LR] [EB] [EC] [PB] [FG] [JFR] [FC/FD] [SB] [SD] [SE] Optical Level Switch Rotary Paddle Level Switch [SA] [SA] Capacitance Level Switch [FF] [EC] [LR] Pressure Level Transmitter Loop Power Indicator [SF] Vibrating Probe Level Switch Tuning Fork Level Switch [SD] [FC/FD] [SP] [EB] [SB] RF-Capacitance Level Transmitter RF-Capacitance / Admittance Level Switch [EE] [EA] [PB/PM] [EG] [EF] Magnetostrictive Level Transmitter By-Pass Level Transmitter [EB] [SB] [SE] [JFR] [EB] [MEF] [EA] Mini By-Pass Level Transmitter Ultrasonic Level Transmitter [SA] [JFR] [EE] FMCW Radar Level Transmitter Electromechanical Level Measuring System [SE] [ED] Speed Monitor [SB] [SRT/SRS] Conveyer Belt Misalignment Switch & Safety Cable Pull Switch [PB/PM] [BRD/AE] [BAS/BAH/BVP] [BVK/BVR/BVT] Microprocessor Based Bargraphic Display Scaling Meter Valve and Controller for Dust Collector System Air Hammer Pneumatic Vibrator [BAS/ BAH/BVP] [BVK/ BVR/BVT] FineTek Co., Ltd. No.6, Tzuchiang St., Tucheng Industrial Park, New Taipei City 36, Taiwan. TEL: FA: info@fine-tek.com Taichung Branch TEL: FA: Tainan Branch TEL: FA: Kaohsiung Branch TEL: FA: Fine automation (ShangHai) Co., Ltd. No.5 DuHui Rd, MinHang District, Shanghai, China 009 TEL: FA: info.sh@fine-tek.com FineTek Pte Ltd. No. 60 Kaki Bukit Place, #07-06 Eunos Techpark Lobby B, Singapore 5979 TEL: FA: info.sg@fine-tek.com Distributor: FineTeK GmbH Frankfurter Str. 6, OG D-658 Ruesselsehim, Germany TEL: FA: info@fine-tek.de Aplus Finetek Sensor inc. 355 S. Lemon Ave, Suite D, Walnut, CA 9789 Tel : Fax : peter.wu@aplusfine.com 08-JFR-B0-EP, 0/5/03