SPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver
|
|
- Sabina Davis
- 5 years ago
- Views:
Transcription
1 2004 Specifications CSJ , , , , , etc, , & SPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver 1. Description. Furnish and install Data Fiber Optic Transceivers in designated equipment cabinets in the field and in the Control Center as shown on the plans and as detailed in the special specifications. 2. Submittal Components. Ensure the submittal for this Item completely addresses the following: - optical wavelength - optical bypass switch - data input/output compatibility - unit physical size - optical input/output power and range - attenuation - data rate normal mode - modulation method bypass mode - bit error rate - system interconnection diagram - transmitting device - transient suppression - optical detector - overcurrent protection - optical fiber compatibility - environmental parameters - power requirements - connectors optical data power gold plating 3. Material. Furnish, assemble, fabricate, or install new corrosion resistant materials under this Item that are in strict accordance with the details shown on the plans and in the specifications. A. Functional Requirements. Provide Data Fiber Optic Transceivers comprised of a transmitter and a receiver that provide the interface between the D/I Muldem and the optical fiber network. Provide a transmitter that converts the T1 rate bit stream from the D/I Muldem to optical signals. Provide a receiver that converts the optical signal to a T1 rate bit stream compatible with the D/I Muldem. Use 2 transceivers at each communications hub, except for the ones at the extremities of the fiber optic trunks, where only 1 transceiver is required
2 Where 2 transceivers are installed, connect 1 transceiver for downstream signal flow and connect the second one for upstream signal flow. B. Electrical/Optical Requirements. 1. Optical Wavelength. The operating wavelength is 1,300 nm. The wavelength and spectral line width selections are based on both the transmitter and the receiver designs. 2. Data Input/Output. Ensure the signal level and line codes operate with a standard pulse code modulation (PCM) T1 data stream (North American PCM DS- 1 line per AT & T Technical Advisory 34) with the bit rate of mb/s. 3. Optical Input Output. Provide a transceiver with an optical output power that is adjustable and sufficient to drive the upstream or downstream receiver at different spacings as indicated on the plans. Ensure the receiver input has the dynamic range to receive the signal from the upstream or downstream transmitter at different spacings. Provide a transceiver which transmits and receives at the D/I Muldem input/output rate of DS-1 over a fiber optic link with a 16 db loss budget while meeting the performance requirements of this specification. 4. Bit Error Rate. Provide a transceiver with a bit error rate better than 10 to the minus 12th power at an operating loss budget of 16 db. 5. Transmitting Device. For the transmitting device, provide a light-emitting diode (LED) which has an MTBF better than 100,000 hours at 71 F. 6. Optical Detector. For the optical detector, provide a transceiver utilizing an APD diode, a PIN, or other approved device. 7. Optical Fiber Compatibility. Provide a multimode transceiver compatible with 50/125 micron multimode graded index glass fiber. Provide a single mode transceiver compatible with 8 to 10 micron single mode glass fiber. 8. Power Requirements. Provide a transceiver that operates from 115 volts AC plus or minus 20 volts AC and draws a maximum of 25 watts of power. Ensure the equipment operation is not affected by transient voltages, surges, and sags normally experienced on commercial power lines. Check the local power service to determine if any special design is needed for the equipment. Include any extra cost for this in the bid price of this Item. 9. Power Service Transients. Provide equipment that meets the requirements of Section 2.1.6, Transients, Power Service, of NEMA Standard TS , latest revision
3 10. Wiring. Provide wiring that meets the requirements of the National Electric Code and is cut to proper length before assembly. Do not double back wire to take up slack. Neatly lace wires into cables with nylon lacing or plastic straps. Secure cables with clamps and provide cable slack to facilitate removal and replacement of assemblies, panels, and modules. 11. Transient Suppression. Provide relays, solenoids, and holding coils with diodes across the coils for transient suppression. 12. Power Service Protection. Provide equipment that contains readily accessible, manually resettable or replaceable circuit protection devices (such as circuit breakers or fuses) for equipment and power source protection. Provide circuit breakers or fuses and size them such that no wires, components, connectors, PC boards, or assemblies are subjected to sustained current in excess of their respective design limits upon the failure of any single circuit element or wiring. 13. Fail Safe Provision. Provide equipment designed such that the failure of the equipment does not cause the failure of any other unit of equipment. Provide a by-pass switch and sensing circuitry to by-pass the D/I Muldem whenever the D/I Muldem loses power or malfunctions. C. Optical Bypass Switch. Provide and install 2 optical bypass switches at each communications hub. Ensure that in the event of a power failure, the optical switches cause the optical T1 data signals to bypass the Data Fiber Optic Transceivers and Drop/Insert Muldem at that particular hub. During normal power service, ensure the optical switches pass the T1 data signals to the Data Fiber Optic Transceivers and Drop/Insert Muldem at that hub. Equip the optical bypass switches with connectors compatible with the optical connectors of the transceiver. The maximum allowable attenuation of the bypass switches is 5 db in bypass mode or in normal mode. Furnish and implement the accessories necessary for complete and operating optical bypass switches. D. Mechanical Requirements. 1. Modular Design. Provide equipment that is modular in design such that major portions may be readily replaced in the field. Mechanically key modules of unlike functions to prevent insertion into the wrong socket or connector. Clearly identify modules and assemblies with name, model number, serial number, and any other pertinent information required to facilitate equipment maintenance. 2. Connectors and Harness. Make external connections by means of connectors. Key the connectors to preclude improper hookups. Color code and appropriately mark wires to and from the connectors. Provide cable slack to facilitate removal and replacement of assemblies, panels, and modules
4 Furnish data input and output connectors that are fully compatible with the T1 connectors of the Drop/Insert Multiplexor. Ensure conductive contact surfaces or pins are plated with a minimum of 50 microns of gold. Provide ST type optical input and output connectors with stainless steel housing and ceramic ferrule for the multimode transceiver. Provide FC type optical input and output connectors for the single mode transceivers. Provide a connecting harness of appropriate length and terminate it with matching connectors for interconnection with the D/I Muldems and the fiber optic network. 3. Housing. Provide a transceiver with a housing that is stainless steel or aluminum protected with corrosion resistant paint and is designed for rack mounting. E. Environmental Design Requirements. Furnish equipment that meets its specified requirements during and after it is subjected to any combination of the following requirements: Ambient temperature range of - 30 F to F. Relative humidity from 0% to 95%. 4. Construction. Utilize the latest available techniques with a minimum number of parts, subassemblies, circuits, cards, and modules to maximize standardization and commonality to design and construct the equipment. Furnish equipment designed for ease of maintenance, with component parts that are readily accessible for inspection and maintenance. Provide test points for checking essential voltages and waveforms. A. Electronic Components. Furnish electronic components that comply with the Special Specification, Electronic Components. B. Mechanical Components. Furnish external screws, nuts, and locking washers that are made of stainless steel; do not use self-tapping screws unless specifically approved by the Engineer. Furnish parts made of corrosion resistant materials, such as plastic, stainless steel, anodized aluminum, or brass. Protect materials used in construction from fungus growth and moisture deterioration. Separate dissimilar metals by an inert dielectric material. C. Testing, Documentation, and Warranty. Test the Data Fiber Optic Transceiver in compliance with Article 2 of the Special Specification, Testing, Training, Documentation, Final Acceptance, and Warranty
5 Provide documentation for the Data Fiber Optic Transceiver in compliance with Article 4 of the Special Specification, Testing, Training, Documentation, Final Acceptance, and Warranty. Provide a warranty for the Data Fiber Optic Transceiver in compliance with Article 5 of the Special Specification, Testing, Training, Documentation, Final Acceptance, and Warranty. 5. Measurement. This Item is measured as each unit of the type shown on the plans furnished, installed, made fully operational, and tested in accordance with this special specification. 6. Payment. The work performed and materials furnished in accordance with this Item and measured as provided under Measurement will be paid for at the unit price bid for Data Fiber Optic Transceiver (Multimode) or Data Fiber Optic Transceiver (Single Mode). This price is full compensation for the equipment described under this Item with cables and connectors; documentation and testing and for furnishing labor, materials, training, and equipment, and incidentals
1995 Metric CSJ SPECIAL SPECIFICATION ITEM Multimode Video Fiber Optic Transmission Equipment
1995 Metric CSJ 3483-01-010 SPECIAL SPECIFICATION ITEM 6329 Multimode Video Fiber Optic Transmission Equipment 1.0 Description. This Item shall govern for the furnishing and installation of Video Fiber
More informationSPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor
1993 Specifications CSJ 0177-11-131 SPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor 1. Description. This Item shall govern for for the furnishing and installation of intelligent drop/insert
More information1995 Metric CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor
1995 Metric CSJ 3256-02-049 1.0 Description SPECIAL SPECIFICATION ITEM 6093 Drop/Insert Multiplexor/Demultiplexor This Item shall govern for the furnishing and installation of intelligent drop/insert multiplexor/demultiplexors
More informationSPECIAL SPECIFICATION 1789 Fiber Optic RS-232 Data Modem
1993 Specifications CSJ 2266-02-095 SPECIAL SPECIFICATION 1789 Fiber Optic RS-232 Data Modem 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic RS- 232 Data Modem
More information1995 Metric CSJ SPECIAL SPECIFICATION ITEM Add/Drop Multiplexor/Demultiplexor
1995 Metric CSJ 0113-13-109 SPECIAL SPECIFICATION ITEM 6225 Add/Drop Multiplexor/Demultiplexor 1.0 Description. This Item shall govern for the furnishing and installation of intelligent Add/Drop Multiplexor/Demultiplexor
More information1993 Specifications CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor
1993 Specifications CSJ 0008-12-071 SPECIAL SPECIFICATION ITEM 6550 Drop/Insert Multiplexor/Demultiplexor 1.0 Description. This Item shall govern for the furnishing and installation of intelligent drop/insert
More informationSPECIAL SPECIFICATION 6609 Fiber Optic Color Video and Data Transmission Equipment
1995 Metric CSJ's 1047-03-056 & 0008-08-066 SPECIAL SPECIFICATION 6609 Fiber Optic Color Video and Data Transmission Equipment 1. Description. This Item shall govern for the furnishing and installation
More informationSPECIAL SPECIFICATION 6734 RS-232 Optical Modem
2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6734 RS-232 Optical Modem 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic RS- 232 Data Modem (OTR) in
More informationSPECIAL SPECIFICATION 6419 Fiber Optic Video Transceiver with Data
2004 Specifications CSJ 0617-01-169 SPECIAL SPECIFICATION 6419 Fiber Optic Video Transceiver with Data 1. Description. This Item shall govern for the furnishing and installation of Video optical transceiver
More informationSPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem
1993 Specifications CSJ s 0902-48-442 & 0902-48-432 SPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem 1. General. This Item shall govern for the furnishing and installation of Spread Spectrum Wireless
More information1995 Metric CSJ , etc. SPECIAL SPECIFICATION ITEM D-I Muldem (Drop/Insert Multiplexor/Demultiplexor)
1995 Metric CSJ 0924-06-156, etc. SPECIAL SPECIFICATION ITEM 6588 D-I Muldem (Drop/Insert Multiplexor/Demultiplexor) 1. Description. This Item shall govern for the furnishing and installation of intelligent
More informationSPECIAL SPECIFICATION 8590 Emergency Vehicle Traffic Signal Priority Control System
2004 Specifications CSJ 0002-01-074, etc. SPECIAL SPECIFICATION 8590 Emergency Vehicle Traffic Signal Priority Control System 1. Description. This Item governs the furnishing and installation of emergency
More informationSPECIAL SPECIFICATION 8340 Dual Band Wireless Ethernet Radios
2004 Specifications CSJ 0914-00-280 SPECIAL SPECIFICATION 8340 Dual Band Wireless Ethernet Radios 1. Description. Furnish and install Dual Band Wireless Ethernet Radios (DBWERs) links for point-to-point
More informationThis Special Provision covers the requirements for the installation and testing of fibre optic modems (FOM).
FIBRE OPTIC MODEMS - Item No. Special Provision No. 683S09 September 2007 1. SCOPE This Special Provision covers the requirements for the installation and testing of fibre optic modems (FOM). 2. REFERENCES
More informationSPECIAL SPECIFICATION 6004 Digital Card Rack Inductive Loop Detector Assembly
2004 Specifications SPECIAL SPECIFICATION 6004 Digital Card Rack Inductive Loop Detector Assembly 1. Description. Furnish and install a digital card rack inductive loop detector assemblies. 2. Materials.
More informationSPECIAL SPECIFICATION LIGHTNING PROTECTION SYSTEM
2004 Specifications CSJ 3622-01-001, ETC. SPECIAL SPECIFICATION 8398 LIGHTNING PROTECTION SYSTEM 1. Description. This Special Specification governs the design and installation of Lightning Protection System
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR WIRELESS INTERCONNECT FOR SIGN MOUNTED FLASHER
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR WIRELESS INTERCONNECT FOR SIGN MOUNTED FLASHER OPR:DJA 1 of 5 C&T:APPR:JAR:DBP:09-01-11 FHWA:APPR:09-01-11 a. Description. This work consists
More informationCable and Port Specifications
APPENDIX D This appendix includes the following information: Cables and Adapters Provided, page D-1 Console Port, page D-2 COM1 Port, page D-3 MGMT 10/100 Ethernet Port, page D-5 SFP Transceiver Specifications,
More informationOvertravel of 3.5 mm max. Power source DC D5C-1DS0 D5C-1DP0 D5C-1DA0 AC D5C-1AS0 D5C-1AP0 D5C-1AA0 Antenna only D5C-00S0 D5C-00P0 D5C-00A0
Touch Switch Unique 18 mm Capacitive Touch Switch with Choice of Three Actuators is Activated with Only a Very Slight Physical Contact Lightweight objects, such as thin wire or foil can be accurately detected.
More informationInstruction Manual MX-480 Bi-directional Multi-Protocol Data
Instruction Manual MX-480 Bi-directional Multi-Protocol Data Copyright 2007, American Fibertek, Inc. 1210JD Table of Contents Functional Description...3 Installation...3 Power Source...3 Power Connection...4
More informationThis special provision is for the installation and testing of the following equipment:
FIBRE OPTIC MODEMS - Item No. Special Provision No. 683F18 April 2005 1. DESCRIPTION This special provision is for the installation and testing of the following equipment: Low Range Fibre Optic Modems
More informationFiberLink 4040 Series
MANUAL FiberLink 4040 Series Four channels of audio over one single mode or multimode fiber. Installation and Operations Manual WWW.ARTEL.COM Contents Contents Welcome... 3 Features... 3 Package Contents...
More informationUser's Manual: Series 350T AC Current Input (External Sensor), DC-Powered Transmitters
User's Manual: Series 350T AC Current Input (External Sensor), DC-Powered Transmitters Table of Contents Page Introduction 1 Description 1 Specifications 2 Installation 3 Calibration 4 General Maintenance
More informationSUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches
SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches PART 1 GENERAL 1.01 Scope Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, and withstand
More informationSPECIAL PROVISION Description of Project, Scope of Contract and Sequence of Work
2004 Specifications CSJ 0110-04-166 SPECIAL PROVISION 000--363 Description of Project, Scope of Contract and Sequence of Work 1. General. The work to be performed on this project consists of furnishing,
More informationF290X / F293X FOM II Series Fiber Optic Isolator Technical Manual
F290X / F293X FOM II Series Fiber Optic Isolator Technical Manual Revision G Copyright 2017 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.com E031130243 PROPRIETARY DATA All data
More informationTOA PROFESSIONAL POWER AMP
Operating Instruction Manual TOA PROFESSIONAL POWER AMP Model P-150M, P-300M TOA ELECTRIC CO, LTD. KOBE, JAPAN Contents Precautions... 2 General Description... 2 Features... 3 Specifications... 4~5 Performance
More informationFiber Optics. Plastic Fiber Optic Transmitter Diode Plastic Connector Housing SFH756 SFH756V
Fiber Optics Plastic Fiber Optic Transmitter Diode Plastic Connector Housing SFH756 Features 2.2 mm Aperture holds Standard 1000 Micron Plastic Fiber No Fiber Stripping Required Good Linearity (Forward
More informationSPECIAL SPECIFICATION Inch LED Traffic Signal Lamp Unit
1993 Specifications SPECIAL SPECIFICATION 1201 12 Inch LED Traffic Signal Lamp Unit 1. Description. This specification describes the minimum acceptable design and performance requirements for a twelve
More informationOP710. Multichannel Optical Power Meter Instruction Manual. (Also supports the OP710-ANX)
Multichannel Optical Power Meter Instruction Manual (Also supports the OP710-ANX) www.optotest.com 1.805.987.1700 Contacting OptoTest Corporation 1.805.987.1700 (7:30 a.m. to 5 p.m. PST) www.optotest.com
More informationPRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian)
PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian) 1.0 General This specification covers the electrical characteristics and
More informationWAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS)
WAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS) 1 PART 1: GENERAL This section describes materials and installation requirements for low voltage
More informationSPECIAL SPECIFICATION 6574 Low Power Wireless Modem
2004 Specifications CSJ 1068-04-126, etc. SPECIAL SPECIFICATION 6574 Low Power Wireless Modem 1. Description. This work shall consist of furnishing and supplying a Low Power Wireless Modem at the locations
More informationSPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack)
1993 Specifications CSJ 0924-06-147, etc. SPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack) 1. Description. This Item shall govern for furnishing, and
More informationWHITE PAPER LINK LOSS BUDGET ANALYSIS TAP APPLICATION NOTE LINK LOSS BUDGET ANALYSIS
TAP APPLICATION NOTE LINK LOSS BUDGET ANALYSIS WHITE PAPER JULY 2017 1 Table of Contents Basic Information... 3 Link Loss Budget Analysis... 3 Singlemode vs. Multimode... 3 Dispersion vs. Attenuation...
More informationSPECIAL SPECIFICATION 6647 Automated Barrier Gate Assembly
1995 Metric CSJ 0015-13-299 SPECIAL SPECIFICATION 6647 Automated Barrier Gate Assembly 1. Description. This Item shall govern for the furnishing and installation of an Automated Barrier Gate (ABG) assembly
More informationPRODUCT INFORMATION B&B ELECTRONICS. Port-Powered RS-232 Fiber Optic Modem with Handshake Support. Model 9PFLST. Description. RS-232 Connections
-01-1/ 00 by B&B Electronics. All rights reserved. Model Port-Powered RS- Fiber Optic Modem with Handshake Support Description The allows any two pieces of RS- asynchronous serial equipment to communicate
More informationTechnical Specifications
Switch Specifications Switch Specifications, on page 1 Power Specifications, on page SFP Transceiver Specifications, on page 4 The following table lists the environmental specifications for the Cisco MDS
More informationOP735. Benchtop Optical Power Meter Instruction Manual
Benchtop Optical Power Meter Instruction Manual www.optotest.com 1.805.987.1700 Contacting OptoTest Corporation 1.805.987.1700 (7:30 a.m. to 5 p.m. PST) www.optotest.com engineering@optotest.com OptoTest
More informationPROFESSIONAL POWER AMP
Operating Instruction Manual PROFESSIONAL POWER AMP Model P-75D, P-150D, P-300D P-75D P-150D P-300D TOA Corporation KOBE, JAPAN Contents Precautions... 1 General Description... 2 Features... 2~ 3 Specifications...
More informationWORLD-BEAM QS18AFF200 Sensors with Foreground Suppression
WORLD-BEAM QS8AFF00 Sensors with Foreground Suppression Datasheet Compact sensors featuring extended range and foreground suppression mode Exceptional optical performance; up to 00 mm sensing range in
More informationRECOMMENDATION ITU-R BT.1367 *
Rec. ITU-R BT.1367 1 RECOMMENDATION ITU-R BT.1367 * Serial digital fibre transmission system for signals Conforming to Recommendations ITU-R BT.656, ITU-R BT.799 and ITU-R BT.1120 (Question ITU-R 42/6)
More informationWLS28-2 UV LED Strip Light
WLS8- UV LED Strip Light Datasheet Banner's WLS8- UV LED Strip Lights have sturdy aluminum housings, shatterproof windows, and impressive environmental ratings, making them a cost-effective operator inspection
More informationAgilent 8761A/B Microwave Switches
Agilent 8761A/B Microwave Switches Product Overview Product Description The Agilent Technologies 8761A and 8761B are single-pole, double-throw coaxial switches with excellent electrical and mechanical
More informationPSI-2450 INTEGRATED CONTROLLER USER GUIDE
PSI-2450 INTEGRATED CONTROLLER PSI-2400-10 LASER DIODE CONTROLLER & PSI-1204-10 MODULATOR BIAS CONTROLLER USER GUIDE Revision B Photonic Systems, Inc. Tel: 978-670-4990 900 Middlesex Turnpike Fax: 978-670-2510
More informationSL300 Snow Depth Sensor USL300 SNOW DEPTH SENSOR. Revision User Manual
USL300 SNOW DEPTH SENSOR Revision 1.1.2 User Manual 1 Table of Contents 1. Introduction... 3 2. Operation... 3 2.1. Electrostatic Transducer... 4 2.2. SL300 Analog Board... 4 2.3. SL300 Digital Circuit
More informationUser Manual. Portable C-band 26dB-gain EDFA Instrument in compact benchtop. (EDFA-C-26G-S, version 1.0b. January 28, 2015) Fiberprime, Inc.
User s Fiberprime, Inc. www.fiberprime.com Tel: 1-613-5964030 Email: info@fiberprime.com Fax: 1-613-8289398 User Manual Portable C-band 26dB-gain EDFA Instrument in compact benchtop (EDFA-C-26G-S, version
More informationMoxa ICF-1280I Series Industrial PROFIBUS-to-Fiber Converter
Moxa ICF-1280I Series Industrial PROFIBUS-to-Fiber Converter Hardware Installation Guide First Edition, August 2013 2013 Moxa Inc. All rights reserved. P/N: 1802012800011 Introduction The ICF-1280I series
More informationThe HFBR-1604 is a selected version of the HFBR-1602, with power specified to meet the
SERCOS Fiber Optic Transmitters and Receiver Technical Data HFBR-0600 Series Features Fully Compliant to SERCOS Optical Specifications Optimized for 1 mm Plastic Optical Fiber Compatible with SMA Connectors
More information1300nm Fast Ethernet Transceiverin1x9SC Duplex Package
1300nm Fast Ethernet Transceiverin1x9SC Duplex Package OPF5102 Technical Data Features 1310nm LED Data Rate: 155Mbps, NRZ Single +3.3V Power Supply PECL Differential Electrical Interface Industry Standard
More informationOrtel (Lucent) Fiber Optic Interface
Ortel (Lucent) Fiber Optic Interface 144-701-1 Serial Number May 5, 2009 Revision B ORTEL (LUCENT) FIBER OPTIC INTERFACE 1. GENERAL INFORMATION... 1 1.1. SCOPE OF OPTION... 1 1.2. PURPOSE OF EQUIPMENT...
More informationModel Sono-Trak Transit Time
Model Sono-Trak Transit Time Ultrasonic Flow Meter Engineered for performance excellence, the Sono-Trak Transit Time ultrasonic meter combines non-invasive, bi-directional measurement with advanced ultrasonic
More informationLIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING
LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING 1.0 General This specification covers the electrical characteristics and general
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK SIG:EMS 1 of 6 APPR:LWB:DBP:07-14-15 FHWA:APPR:07-28-15 a. Description. This work consists of site
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK SIG:CJS 1 of 6 APPR:EMS:DBP:06-29-17 FHWA:APPR:08-14-17 a. Description. This work consists of completing
More informationRoHS Compliant 1310 nm Single-mode Transceiver (L1.1) 2 5, LC Duplex Connector, 3.3 V 155 Mbps ATM/SONET OC-3/SDH STM-1/Fast Ethernet
Features Compliant with 155 Mbps ATM and SONET OC-3 SDH STM-1 (L1.1) Industry standard 2 5 footprint LC duplex connector Single power supply 3.3 V Differential LVPECL inputs and outputs Compatible with
More informationUser's Manual: Series 450T AC Current Input (External Sensor), AC-Powered Transmitters
User's Manual: Series 450T AC Current Input (External Sensor), AC-Powered Transmitters Table of Contents Page Introduction 1 Description 1 Specifications 2 Installation 3 Calibration 4 General Maintenance
More informationaf-phy July 1996
155.52 Mbps Short Wavelength Physical Layer Specification af-phy-0062.000 Technical Committee 155.52 Mbps Physical Layer Interface Specification for Short Wavelength Laser af-phy-0062.000 July 1996 1 ATM
More informationElectronic Circuit Breaker with reset input ESS20-1..
Electronic Circuit Breaker with reset input ESS0-.. Description The special device ESS0-.. is a further extension of the product line electronic circuit breakers. Type ESS0-.. has a width of only. mm and
More informationDC to 3.5-GHz Amplified Photoreceivers Models 1591 & 1592
USER S GUIDE DC to 3.5-GHz Amplified Photoreceivers Models 1591 & 1592 These photoreceivers are sensitive to electrostatic discharges and could be permanently damaged if subjected even to small discharges.
More informationWORLD-BEAM QS18AF Sensor with Background Suppression
WORLD-BEAM QS8AF Sensor with Background Suppression Datasheet Compact sensors featuring extended range and background suppression mode Exceptional optical performance; up to 00 mm sensing range in compact
More informationMODEL FLD-496SA 9600 Baud FIBER OPTIC/FSK MODEM
1 MODEL FLD-496SA 9600 Baud FIBER OPTIC/FSK MODEM GDI COMMUNICATIONS, LLC 280 Interstate 80 Exit 1 PO Box 1330 Verdi, NV 89439 Phone (775) 345-8000 Fax (775) 345-8010 PROPRIETARY DATA This document contains
More informationSTATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 919 RAILROAD PREEMPTION INTERFACE. January 15, 2016
STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 919 RAILROAD PREEMPTION INTERFACE January 15, 2016 919.01 Traffic Signal Cabinet and Controller Unit General Requirements 919.02 Approved
More information4 Channel Contact Closure DIN Fiber Link System
USER GUIDE RLH Industries, Inc. The leader in rugged fiber optic technology. U-027 2018A-0213 4 Channel Contact Closure DIN Fiber Link System SYSTEM INSTALLATI INFORMATI Description The 4 Channel Contact
More informationInstruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels
Instruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels Copyright 2006, American Fibertek, Inc. 0307JD Table of Contents Functional Description... 3 Installation...
More informationSPECIFICATION FOR HORIZONTAL AIRFLOW OUTDOOR RESISTIVE LOAD BANK
SPECIFICATION FOR HORIZONTAL AIRFLOW OUTDOOR RESISTIVE LOAD BANK PART 1.0 GENERAL 1.1 SCOPE A. This specification contains the minimum requirements for the design, manufacture and testing of a UL listed,
More informationTIA-1200 Optical / Electrical Converter Operating Instructions
TIA-1200 Optical / Electrical Converter Operating Instructions Contents Introduction...1 Specifi cations...2 Unpackaging and Inspection...3 Power Supply...3 Setup...4 Operating Considerations...5 Service/Warranty
More informationOrtel (Lucent) Fiber Optic Interface AC
Ortel (Lucent) Fiber Optic Interface 144-701-1AC Serial Number March 11, 2010 CD P/N 098-00126-000 Revision B ORTEL (LUCENT) FIBER OPTIC INTERFACE 1. GENERAL INFORMATION... 1 1.1. SCOPE OF OPTION... 1
More informationRAM-34 RX Pre-amplifier System Installation and Operation Manual
RAM-34 RX Pre-amplifier System Installation and Operation Manual ( www.hamation.com ) RAM-34 Front and Rear Views Introduction The RAM-34 is a complete pre-amplifier system designed primarily for the low
More informationDC to 12-GHz Amplified Photoreceivers Models 1544-B, 1554-B, & 1580-B
USER S GUIDE DC to 12-GHz Amplified Photoreceivers Models 1544-B, 1554-B, & 1580-B Including multimode -50 option These photoreceivers are sensitive to electrostatic discharges and could be permanently
More informationRoHS compliant 1310 nm Single-mode Transceiver (S1.1, 19dB margin) 1x9, SC Duplex Connector, 3.3 V 155 Mbps ATM/SONET OC-3/SDH STM-1/Fast Ethernet
Features Compliant with 155 Mbps ATM and SONET OC-3 SDH STM-1 (S1.1) Industry standard 1 9 footprint SC duplex connector Single power supply 3.3 V Differential LVPECL inputs and outputs Compatible with
More informationFOSTCDR. Industrial Serial to Multimode Fiber Optic Converter PRODUCT INFORMATION B&B ELECTRONICS. Specifications Serial Technology
FOSTCDR pn 8684R1 FOSTCDR-0812ds page 1/5 Industrial Serial to Multimode Fiber Optic Converter Data Rates up to 115.2 kbps 2.5 Mile (4 km) Range 10 to 30 VDC Input Voltage Wide Operating Temperature 2000V
More informationLow Voltage Power Factor Correction Equipment Specifications Automatic, Automatic Detuned, Automatic Tuned
Low Voltage Power Factor Correction Equipment Specifications Automatic, Automatic Detuned, Automatic Tuned Part 1 - General Scope and Product Description 1.0 This specification contains the minimum design
More informationLiquid Level Detector
Liquid Level Detector Made in the USA MERCURY & LEAD FREE, MERCURY & LEAD FREE, NON-MECHANICAL NON-MECHANICAL 12 MILLION OPERATIONS Combining new technology with a familiar device, the Opti-Float level
More informationph or ORP Transmitter
ph or ORP Transmitter Programmable outputs: two transistor and single or dual analog 4-20 ma (Process + Temp) Removable backlighted display Universal process connection Compatible with 120 mm ph/ ORP probes
More informationM12 Class 1 Laser Emitter
IEC Class 1 Laser for use with Banner modulated receivers CAUTION... Never stare directly into the emitter lens. Laser light can damage your eyes. Avoid placing any mirror-like object in the beam. Never
More informationTOSHIBA International Corp
TOSHIBA International Corp GUIDE SPECIFICATIONS THREE PHASE UNINTERRUPTIBLE POWER SYSTEM TOSHIBA 4200FA 30 kva CT Internal Battery UPS GUIDE SPECIFICATIONS 1 (30 kva CT) 1.0 SCOPE 1.1 System This specification
More informationExternal RF Driver. Electrical Driver for AOTF-crystal. Instruction Manual
External RF Driver Electrical Driver for AOTF-crystal Instruction Manual Table of Contents 1 General... 3 2 Compliance... 3 3 Labeling... 4 4 Interface... 5 4.1 Front Panel... 5 4.2 Back Panel... 6 4.2.1
More informationDocument # Rev. C October, GEMINI EXPRESS MULTIPLEXER User s Guide
Document # 400-2601-01 Rev. C October, 2002 GEMINI EXPRESS MULTIPLEXER User s Guide TABLE OF CONTENTS SAFETY 3 Federal Communications Commission (FCC) Statement 3 Classification of LED Transmitter Device
More informationInstruction Manual MX-485-S Bi-directional RS485 Data Transceiver
Instruction Manual MX-485-S Bi-directional RS485 Data Transceiver Copyright 2005, American Fibertek, Inc. 1020JD Table of Contents Functional Description...3 Installation...3 Power Source...3 Power Connection...3
More informationRoHS compliant 1310 nm multi-mode Transceiver (2 km) 1x9, SC Duplex Connector, 5.0 V 155 Mbps ATM/ Fast Ethernet
Features RoHS compliant Industry standard 1 9 footprint SC duplex connector Single power supply 5.0 V Differential LVPECL inputs and outputs Compatible with solder and aqueous wash processes Class 1 laser
More information285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM
285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result
More informationMirage B-320-G FEATURES
Mirage B-320-G The Mirage B-320-G is a VHF power amplifier designed for 2 meters covering 144-148 MHz. The Hi and Lo input selector switch makes this amp useable for both handheld and mobile transceivers.
More informationFIBER105.TIF OUTLINE DIMENSIONS in inches (mm) .176 (4.47).165 (4.19) .500 MIN (12.7) FIBER203.DIM. Pinout 1. Capacitor 2. VÙÙ 3.
FEATURES Converts fiber optic input signals to TTL digital outputs Typical sensitivity 500 nw peak ( 33 dbm) Single 5 V supply requirement Edge detection circuitry gives 20 db minimum dynamic range, low
More informationSECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section
02760-1 of 5 SECTION 02760 STEEL LIGHTING STANDARDS 02760.01 GENERAL A. Description Steel lighting standards shall include, but not necessarily be limited to, furnishing and installing steel lighting poles,
More information10 GHz Microwave Link
10 GHz Microwave Link Project Project Objectives System System Functionality Testing Testing Procedures Cautions and Warnings Problems Encountered Recommendations Conclusion PROJECT OBJECTIVES Implement
More informationCISCO DWDM GBICS. Figure 1. Cisco DWDM GBICs. Main features of the Cisco DWDM GBICs:
DATA SHEET CISCO DWDM GBICS The Cisco Dense Wavelength-Division Multiplexing (DWDM) Gigabit Interface Converter (GBIC) pluggables allow enterprise companies and service providers to provide scalable and
More informationSPECIAL SPECIFICATION 6744 Spread Spectrum Radio
2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6744 Spread Spectrum Radio 1. Description. Furnish and install spread spectrum radio system. 2. Materials. Supply complete manufacturer specifications
More information2017 Advanced Energy Industries, Inc. PEII SERIES LOW-FREQUENCY POWER SUPPLIES 5 TO 60 KW
2017 Advanced Energy Industries, Inc. PEII SERIES LOW-FREQUENCY POWER SUPPLIES 5 TO 60 KW Enhanced arc control with internal load matching for 40 khz reactive sputtering applications Page 2 The PEII power
More informationFeatures. Applications
HFBR-8 Series HFBR-8 Transmitter HFBR-8 Receiver Megabaud Versatile Link Fiber Optic Transmitter and Receiver for mm POF and µm HCS Data Sheet Description The HFBR-8 Series consists of a fiber-optic transmitter
More informationSINGLE-PHASE VSV SWITCH
May 2006 Supercedes: March 2006 SINGLE-PHASE VSV SWITCH INSTALLATION AND OPERATING MANUAL Table of Content: Page I. General...2 II. Specifications...2 III. Installation...2 IV. Maintenance...4 V. VSV Power
More informationRoHS compliant 1310 nm Single-mode Transceiver (L1.1) 1x9, ST Duplex Connector, 3.3 V 155 Mbps ATM/SONET OC-3/SDH STM-1/Fast Ethernet.
Features Compliant with 155 Mbps ATM and SONET OC-3 SDH STM-1 (L1.1) Industry standard 1 9 footprint ST duplex connector Single power supply 3.3 V Differential LVPECL inputs and outputs Compatible with
More informationInstruction Manual Model M Switch, DPDT, Manual Select
Instruction Manual Model 1582-70M Switch, DPDT, Manual Select November 2018 Rev 0 STATUS MODEL 1582 CROSS TECHNOLOGIES INC. MANUAL SELECT POWER Data, drawings, and other material contained herein are proprietary
More informationPARAMETER SYMBOL MIN MAX UNITS NOTE
Features Industry standard 2 5 footprint SC Connector Single power supply 3.3 V Differential PECL inputs and outputs Compatible with solder and aqueous wash processes Class 1 laser product complies with
More informationUser's Manual: Series 250T AC Current Input (External Sensor) Two-Wire Transmitters
User's Manual: Series 250T AC Current Input (External Sensor) Two-Wire Transmitters Table of Contents Page INTRODUCTION: Introduction 1 Description 1 Specifications 2 Specifications (Display Option) 4
More information15-GHz & 25-GHz Photodetectors Models 1480-S & 1481-S
1480-S FC Det revb.fm Page 1 Monday, January 14, 2013 11:38 AM USER S GUIDE 15-GHz & 25-GHz Photodetectors Models 1480-S & 1481-S Includes Model 1481-50-S These photodetectors are sensitive to electrostatic
More informationOM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount)
OM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount) IRIG Time Code Electrical to Fiber Optic Transceiver Operating Manual Rev. 1.3 December 20, 2015 Luxcom Technologies Inc., 102 WALGREEN ROAD,
More informationPOLARIZATION EXTINCTION RATIO MEASUREMENT TEST SETFOR V-GROOVE ASSEMBLIES AND PM PATCHCORDS
219 Westbrook Rd, Ottawa, ON, Canada, K0A 1L0 Toll Free: 1-800-361-5415 Tel:(613) 831-0981 Fax:(613) 836-5089 E-mail: sales@ozoptics.com POLARIZATION EXTINCTION RATIO MEASUREMENT TEST SETFOR V-GROOVE ASSEMBLIES
More informationRoHS compliant 850 nm Multi-mode Transceiver Gigabit Interface Converter (GBIC), 3.3V/5V Gbd Fiber Channel/1.25 Gigabit Ethernet.
Features Compliant with Gigabit Interface Converter Specification Compliant with IEEE802.3z Gigabit Ethernet standard Compliant with Fiber Channel standard SCA-2 Host connector Duplex SC connector Differential
More informationDetection of Incorrectly Set Work Press Position Confirmation Detection of Bent Drills. Press D5C
Touch Switch CSM DS_E 3 Unique 18-mm-dia. Capacitive Touch Switch with Choice of Three Actuators is Activated with Only a Very Slight Physical Contact Only a slight activation force is required, enabling
More information