6.8 to 250 Volt DEVICES FOR BIPOLAR APPLICATIONS
|
|
|
- Margaret Rogers
- 5 years ago
- Views:
Transcription
1 SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR POWER 400 Watt BREAK DOWN VOLTAGE 6.8 to 250 Volt FEATURES For surface mounted applications in order to optimize board space Glass passivated junction Low inductance Plastic package has Underwriters Laboratory Flammability Classification 94V-O High temperature soldering : 260 C / seconds at terminals ESD IEC Air + 30kV, Contact + 30kV Lead free in compliance with EU RoHS 2.0 Green molding compound as per IEC standard MECHANICAL DATA Case: JEDEC DO-214AC,Molded plastic over passivated junction. Terminals: Solder plated,solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Standard Packaging: 12mm tape (EIA-481) Weight: ounce, gram DEVICES FOR BIPOLAR APPLICATIONS For Bidirectional use C or CA Suffix for types P4SMA6.8 thru types P4SMA250. Electrical characteristics apply in both directions. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Rating Symbol Value Units Peak Pulse Power Dissipation on T A = 25 O C (Notes 1,2,5, Fig.1) P PP 400 Watts ESD IEC (Air) ESD IEC (Contact) VESD kv Peak Forward Surge per Fig.5 (Notes 3) I FSM 40 Amps Peak Pulse on tp=/00μs waveform (Notes 1)Fig.2 I PPM see Table 1 Amps Typical Thermal Resistance Junction to Air (Notes 2) R θja 70 O C / W Operating Junction and Storage Temperature Range T J,T STG -55 to +150 O C NOTES : 1. Non-repetitive current pulse, per Fig.3 and derated above T A = 25 O C per Fig Mounted on 5mm 2 copper pads to each terminal ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minutes maximum. 4. Lead temperature at 75 O C = T L. 5. Peak pulse power waveform is /00μs. 6. A transient suppressor is selected according to the working peak reverse voltage (VRWM), which should be equal to or greater than the DC or continuous peak operating voltage level. PAGE. 1
2 Part Number Stand-off VRWM (Notes 6) Breakdown I T Test IT Leakage I VRWM Min. Max. UNI BI Max. Clamp /00μs I PP Peak Pulse /00μs I PP Marking Code UNI BI V V V ma μa μa V A UNI BI 400W Transient Suppressor P4SMA6.8 P4SMA6.8C MZA NZA P4SMA6.8A P4SMA6.8CA MZB NZB P4SMA7.5 P4SMA7.5C MZC NZC P4SMA7.5A P4SMA7.5CA MZD NZD P4SMA8.2 P4SMA8.2C MZE NZE P4SMA8.2A P4SMA8.2CA MZF NZF P4SMA9.1 P4SMA9.1C MZG NZG P4SMA9.1A P4SMA9.1CA MZH NZH P4SMA P4SMAC MZJ NZJ P4SMAA P4SMACA MZK NZK P4SMA11 P4SMA11C MZL NZL P4SMA11A P4SMA11CA MZM NZM P4SMA12 P4SMA12C MZN NZN P4SMA12A P4SMA12CA MZP NZP P4SMA13 P4SMA13C MZQ NZQ P4SMA13A P4SMA13CA MZR NZR P4SMA15 P4SMA15C MZS NZS P4SMA15A P4SMA15CA MZT NZT P4SMA16 P4SMA16C MZU NZU P4SMA16A P4SMA16CA MZV NZV P4SMA18 P4SMA18C MZW NZW P4SMA18A P4SMA18CA MZX NZX P4SMA20 P4SMA20C MZY NZY P4SMA20A P4SMA20CA MZZ NZZ P4SMA22 P4SMA22C MXA NXA P4SMA22A P4SMA22CA MXB NXB P4SMA24 PSMA24C MXC NXC P4SMA24A P4SMA24CA MXD NXD P4SMA27 P4SMA27C MXE NXE P4SMA27A P4SMA27CA MXF NXF P4SMA30 P4SMA30C MXG NXG P4SMA30A P4SMA30CA MXH NXH P4SMA33 P4SMA33C MXJ NXJ P4SMA33A P4SMA33CA MXK NXK P4SMA36 P4SMA36C MXL NXL P4SMA36A P4SMA36CA MXM NXM P4SMA39 P4SMA39C MXN NXN P4SMA39A P4SMA39CA MXP NXP P4SMA43 P4SMA43C MXQ NXQ PAGE. 2
3 Part Number Stand-off VRWM (Notes 6) Breakdown I T Test IT Leakage I VRWM Min. Max. UNI BI Max. Clamp I PP Peak Pulse I PP Marking Code UNI BI V V V ma μa μa V A UNI BI 400W Transient Suppressor P4SMA43A P4SMA43CA MXR NXR P4SMA47 P4SMA47C MXS NXS P4SMA47A P4SMA47CA MXT NXT P4SMA51 P4SMA51C MXU NXU P4SMA51A P4SMA51CA MXV NXV P4SMA56 P4SMA56C MXW NXW P4SMA56A P4SMA56CA MXX NXX P4SMA62 P4SMA62C MXY NXY P4SMA62A P4SMA62CA MXZ NXZ P4SMA68 P4SMA68C MYA NYA P4SMA68A P4SMA68CA MYB NYB P4SMA75 P4SMA75C MYC NYC P4SMA75A P4SMA75CA MYD NYD P4SMA82 P4SMA82C MYE NYE P4SMA82A P4SMA82CA MYF NYF P4SMA91 P4SMA91C MYG NYG P4SMA91A P4SMA91CA MYH NYH P4SMA0 P4SMA0C MYJ NYJ P4SMA0A P4SMA0CA MYK NYK P4SMA1 P4SMA1C MYL NYL P4SMA1A P4SMA1CA MYM NYM P4SMA120 P4SMA120C MYN NYN P4SMA120A P4SMA120CA MYP NYP P4SMA130 P4SMA130C MYQ NYQ P4SMA130A P4SMA130CA MYR NYR P4SMA150 P4SMA150C MYS NYS P4SMA150A P4SMA150CA MYT NYT P4SMA160 P4SMA160C MYU NYU P4SMA160A P4SMA160CA MYV NYV P4SMA170 P4SMA170C MYW NYW P4SMA170A P4SMA170CA MYX NYX P4SMA180 P4SMA180C MYY NYY P4SMA180A P4SMA180CA MYZ NYZ P4SMA200 P4SMA200C MWA NWA P4SMA200A P4SMA200CA MWB NWB P4SMA220 P4SMA220C MWC NWC P4SMA220A P4SMA220CA MWD NWD P4SMA250 P4SMA250C MWE NWE P4SMA250A P4SMA250CA MWF NWF PAGE. 3
4 P PPM - Peak Pulse Power(kW) Non-Repetive Pluse Waverform Shown in Figure 3 T A = 25 C 1 0 1,000,000 t d - Pulse Width(us) Fig.1 Pulse Power Rating Curve P PP or I PP Derating Percentage (%) T A - Ambient Temperature( C) Fig.2 Derating Curve Percent of I PP (%) % of I Rise time ~90 %- us Time (ms) Fig.3 /00us Pulse Waveform C J - Junction Capacitance(pF),000 1, Bi-direc onal V R = 0 V Uni-direc onal V R = 0 V V RWM - Stand-off (V) Fig.4 Typical Capacitance PAGE. 4
5 MOUNTING PAD LAYOUT ORDER INFORMATION Packing information T/R - 7.5K per 13" plastic Reel T/R - 1.8K per 7" plastic Reel PAGE. 5
6 Part No_packing code_version P4SMA6.8_R1_00001 P4SMA6.8_R2_00001 For example : RB500V-40_R2_00001 Part No. Serial number Version code means HF Packing size code means 13" Packing type means T/R Packing Code XX Version Code XXXXX Packing type 1 st Code Packing size code 2 nd Code HF or RoHS 1 st Code 2 nd ~5 th Code Tape and Ammunition Box (T/B) Tape and Reel (T/R) Bulk Packing (B/P) Tube Packing (T/P) Tape and Reel (Right Oriented) (TRR) Tape and Reel (Left Oriented) (TRL) FORMING A N/A 0 HF 0 serial number R 7" 1 RoHS 1 serial number B 13" 2 T 26mm X S 52mm Y L F PANASERT T/B CATHODE UP (PBCU) PANASERT T/B CATHODE DOWN (PBCD) U D PAGE. 6
7 Disclaimer Reproducing and modifying information of the document is prohibited without permission from Panjit International Inc.. Panjit International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. Panjit International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. Panjit International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications. Panjit International Inc. makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panjit International Inc. for any damages resulting from such improper use or sale. Since Panjit uses lot number as the tracking base, please provide the lot number for tracking when complaining. PAGE. 7
DEVICES FOR BIPOLAR APPLICATIONS
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR POWER 400 Watts BREAK DOWN VOLTAGE 6.8 to 250 Volts FEATURES For surface mounted applications in order to optimize board space Glass passivated junction Low inductance
PP4SMA6.8-AU ~ P4SMA82CA-AU Series
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Voltage 6.8~82 V Power 400 W Features ISO605(C=330 pf,r=330ω): ± 30kV Air, ± 30kV Contact HBM ± 8 kv & CDM ± 2 kv AEC-Q1 qualified Lead free in compliance with
PP4SMA6.8A-AU ~ P4SMA82CA-AU Series
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Voltage 6.8~82 V Power 400 W Features ISO605(C=330 pf,r=330ω): ± 30kV Air, ± 30kV Contact HBM ± 8 kv & CDM ± 2 kv AEC-Q1 qualified Lead free in compliance with
GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR POWER 600 Watt DEVICES FOR BIPOLAR APPLICATIONS
GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR POWER 600 Watt BREAK DOWN VOLTAGE 6.8 to 550 Volt FEATURES Recongnized File # E210467 Plastic package has Underwriters Laboratory Flammability Classification
5 to 70 Volt DEVICES FOR BIPOLAR APPLICATIONS
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR POWER 600 Watt STAND-OFF VOLTAGE 5 to 70 Volt Recongnized File # E210467 FEATURES For surface mounted applications in order to optimize board space AEC-Q101 qualified
US1R SURFACE MOUNT ULTRAFAST RECTIFIER FEATURES MECHANICAL DATA MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS. VOLTAGE 1300 Volt CURRENT 1 Ampere
SURFACE MOUNT ULTRAFAST RECTIFIER VOLTAGE 300 Volt CURRENT Ampere FEATURES For surface mounted applications in order to optimize board space Easy pick and place Ultrafast recovery times for high efficiency
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
MS4~MS20 SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER VOLTAGE 40 to 200 Volt CURRENT Ampere FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94V-O For surface mounted applications
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR PEAK PULSE POWER 5000 Watt. 20 to 250 Volt MAXIMUM RATINGS AND CHARACTERISTICS. Rating Symbol Value Units
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR PEAK PULSE POWER 5000 Watt STAND-OFF VOLTAGE 20 to 250 Volt FEATURES For surface mounted applications in order to optimize board space. Glass passivated junction
1 Watt MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
SURFACE MOUNT SILICON ZENER DIODE VOLTAGE 3.3 to 51 Volt POWER 1 Watt FEATURES For surface mounted applications in order to optimize board space Low inductance Plastic package has Underwriters Laboratory
Green molding compound as per IEC61249 Std.. (Halogen Free) 0.098(2.5) 0.086(2.2)
SURFACE MOUNT GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 50 to 1000 Volt CURRENT 1 Ampere FEATURES Recongnized File #E111753 0.335(8.51) 0.316(8.05) 0.009(0.25) 0.060(1.524) 0.040(1.016) Plastic
RS1AWG SERIES SURFACE MOUNT FAST RECOVERY RECTIFIER FEATURES MECHANICAL DATA MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
SURFACE MOUNT FAST RECOVERY RECTIFIER VOLTAGE 50 to 000 Volts CURRENT Amperes FEATURES For surface mounted applications in order to optimize board space Easy pick and place Fast recovery times for high
MB18F SERIES SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER. VOLTAGE Volt CURRENT 1 Ampere FEATURES MECHANICAL DATA
SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER VOLTAGE 80-200 Volt CURRENT Ampere FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94V-O For surface mounted applications Ultra
Rating Symbol Value Units T STG. Parameter Symbol Conditions Min. Typical Max. Units I BR V R I PP
SINGLE LINE TVS DIODE FOR ESD PROTECTION PORTABLE ELECTRONICS VOLTAGE 5 Volt POWER 200 Watt FEATURES 200 Watts peak pules power( tp=8/20μs) Small package for use in portable electronics IEC61000-4-2 8KV
SS12L SERIES LOW VF SURFACE MOUNT SCHOTTKY RECTIFIER MECHANICAL DATA. VOLTAGE 20 to 90 Volt CURRENT 1.0 Ampere FEATURES
LOW VF SURFACE MOUNT SCHOTTKY RECTIFIER VOLTAGE 20 to 90 Volt CURRENT.0 Ampere FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94V-O For surface mounted applications Low
PJSRV05-4 LOW CAPACITANCE TVS DIODE ARRAY. VOLTAGE 5 Volt POWER 350 Watt FEATURES MECHANICAL DATA APPLICATIONS MAXIMUM RATINGS
LOW CAPACITANCE TVS DIODE ARRAY The PJSRV5-4 has a low capacitance of 1.2pF and operates with virtually no insertion loss to 1GHz. This makes the device ideal for protection of high-speed data lines such
MICRO SURFACE MOUNT GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 400~1000 Volt CURRENT 1.2 Amper. per diode I FSM 50 A
MICRO SURFACE MOUNT GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 400~000 Volt CURRENT.2 Amper FEATURES Glass Passivated Chip Junciton Ideally Suited for Automatic Assembly Save Space On Printed
PJSD05LCFN2 TYPICAL CHARACTERISTIC CURVES. I R,Reverse Current (na) Percent of Rated Peak Reverse Voltage (%) time, s.
BI-DIRECTIONAL ESD PROTECTION DIODE This bi-directional TVS has been designed to protect sensitive equipment against ESD and to prevent Latch-Up events in CMOS circuitry operating at 5V dc and below.this
MMBD914 SURFACE MOUNT SWITCHING DIODE. VOLTAGE 100 Volt POWER 225 mwatt FEATURES MECHANICAL DATA ABSOLUTE RATINGS THERMAL CHARACTERISTICS
SURFACE MOUNT SWITCHING DIODE VOLTAGE 100 Volt POWER 225 mwatt FEATURES Very fast reverse recovery (Trr < 2ns typical) Low capacitance (4pF @ 0V typical) Surface mount package ideally suited for automatic
MICRO SURFACE MOUNT GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 100~1000 Volt CURRENT 1 Amper Recongnized File #E139973
MICRO SURFACE MOUNT GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 100~1000 Volt CURRENT 1 Amper Recongnized File #E139973 FEATURES Glass Passivated Chip Junciton Ideally Suited for Automatic Assembly
SK54BLF LOW VF SCHOTTKY RECTIFIER. VOLTAGE 40 Volt CURRENT 5 Ampere FEATURES MECHANICAL DATA. MAXIMUM RATINGS (TA=25 o C unless otherwise noted)
LOW VF SCHOTTKY RECTIFIER VOLTAGE 40 Volt CURRENT 5 Ampere FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94VO utilizing Flame Retardant Expoxy Molding Compound Ultra
1.5SMCJ5.0A-AU~1.5SMCJ70CA-AU
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR PEAK PULSE POWER 1500 Watt STAND-OFF VOLTAGE 5 to 70 Volt Recongnized File # E2467 FEATURES For surface mounted applications in order to optimize board space.
BAS100ATB6 SURFACE MOUNT DUAL ISOLATED OPPOSING SILICON SCHOTTKY DIODES. VOLTAGE 100 Volt FEATURES MECHANICAL DATA
SURFACE MOUNT DUAL ISOLATED OPPOSING SILICON SCHOTTKY DIODES VOLTAGE 00 Volt FEATURES Smallest 00V Dual, isolated Schottky diode currently available Lead free in compliance with EU RoHS 20/65/EU directive
2N7002KDW. 60V N-Channel Enhancement Mode MOSFET - ESD Protected. Parameter Symbol Limit Units 60 V. Drain-Source Voltage V DS + 20 V
60V N-Channel Enhancement Mode MOSFET - ESD Protected FEATURES R DS(ON), @10V,I DS @500mA=3Ω R DS(ON), @4.5V,I DS @200mA=4Ω Advanced Trench Process Technology High Density Cell Design For Ultra Low On-Resistance
1N4736A SERIES SILICON ZENER DIODE MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS FEATURES MECHANICAL DATA
N4736A SERIES SILICON ZENER DIODE VOLTAGE 6.8 to Volt POWER Watt FEATURES Low inductance High temperature soldering : 260 C /0 seconds at terminals Plastic package has Underwriters Laboratory Flammability
SK23L SERIES. LOW VF SCHOTTKY RECTIFIER VOLTAGE 30 to 100 Volts CURRENT 2.0 Amperes FEATURES MECHANICAL DATA
LOW VF SCHOTTKY RECTIFIER VOLTAGE 30 to 00 Volts CURRENT 2.0 Amperes FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94VO For surface mounted applications Low profile package
BAV3004W HIGH VOLTAGE SURFACE MOUNT SWITCHING DIODE
HIGH VOLTAGE SURFACE MOUNT SWITCHING DIODE VOLTAGE 350 Volts POWER 410 mwatts SOD-123 Unit:inch(mm) FEATURES Fast Switching Speed Surface Mount Package ldeally Suited for Automatic Insertion High Conductance
SXM54ALF ULTRA LOW VF SCHOTTKY RECTIFIER. VOLTAGE 45 Volt CURRENT 5 Ampere FEATURES MECHANICAL DATA. MAXIMUM RATINGS(TA=25 o C unless otherwise noted)
ULTRA LOW VF SCHOTTKY RECTIFIER VOLTAGE 45 Volt CURRENT 5 Ampere FEATURES Ideal for automated placement Ultra Low forward voltage drop, low power loss High efficiency operation Low thermal resistance Ultra
SVM1045V2 LOW VF SCHOTTKY RECTIFIER. VOLTAGE 45 Volt CURRENT 10 Ampere FEATURES MECHANICAL DATA. MAXIMUM RATINGS(TA=25 o C unless otherwise noted)
.. LOW VF SCHOTTKY RECTIFIER VOLTAGE 45 Volt CURRENT Ampere FEATURES Ideal for automated placement Low forward voltage drop, low power loss High efficiency Operation Low thermal resistance 0.172(4.35)
ES1A~ES1J SURFACE MOUNT SUPERFAST RECTIFIER FEATURES MECHANICAL DATA MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
SURFACE MUNT SUPERFAST RECTIFIER VLTAGE 5 to 6 Volts CURRENT 1 Amperes FEATURES For surface mounted applications in order to optimize board space Built-in strain relief Easy pick and place Superfast recovery
1N4148W SURFACE MOUNT SWITCHING DIODES. VOLTAGE 100 Volt POWER 410mWatt FEATURES MECHANICAL DATA
SURFACE MUNT SWITCHING DIDES VLTAGE 100 Volt PWER 410mWatt FEATURES 0.154(3.90) 0.141(3.60) Fast switching Speed. Electrically ldentical to Standerd JEDEC High Conductance Surface Mount Package ldeally
SVM1045V LOW VF SCHOTTKY RECTIFIER. VOLTAGE 45 Volt CURRENT 10 Ampere FEATURES MECHANICAL DATA. MAXIMUM RATINGS(TA=25 o C unless otherwise noted)
.. SVM45V LOW VF SCHOTTKY RECTIFIER VOLTAGE 45 Volt CURRENT Ampere FEATURES Ideal for automated placement Ultra low forward voltage drop, low power loss High efficiency Operation 0.172(4.35) 0.167(4.25)
2N7002KTB. 60V N-Channel Enhancement Mode MOSFET - ESD Protected FEATURES MECHANICAL DATA. =25 O C unless otherwise noted )
6V N-Channel Enhancement Mode MOSFET - ESD Protected FEATURES R DS(ON), @V,I DS @5mA=3Ω R DS(ON), @4.5V,I DS @2mA=4Ω Advanced Trench Process Technology High Density Cell Design For Ultra Low On-Resistance
PJSD12LCFN2 BI-DIRECTIONAL ESD PROTECTION DIODE
BIDIRECTIONAL ESD PROTECTION DIODE This bidirectional TVS has been designed to protect sensitive equipment against ESD and to prevent LatchUp events in CMOS circuitry operating at 12Vdc and below.this
PUF5GI / UF504IG ULTRAFAST RECOVERY RECTIFIERS. Voltage 400 V Current 5 A. Features UF504IG DO-201AD. Mechanical Data UF5GI SMC
ULTRAFAST RECOVERY RECTIFIERS Voltage 400 V Current 5 A Features Silicon epitaxial high-speed diodes Soft recovery characteristics Low forward voltage, high current capability Hermetically sealed. Low
PJSD05CW-AU SERIES. Fig.130. Single Line TVS Diode for ESD Protection in Portable Electronics FEATURES MECHANICAL DATA ABSOLUTE MAXIMUM RATINGS
PJSD5W-AU SERIES Single Line TVS Diode for ESD Protection in Portable Electronics VOLTAGE 5 to 36 Volt POWER 35 Watt FEATURES Transient protection for data lines to IE 61-4-2 (ESD) + 15kV (air),+ 8kV (contact).78(1.95).68(1.75)
PJSD03TS~PJSD36TS. SINGLE LINE TVS DIODE FOR ESD PROTECTION PORTABLE ELECTRONICS VOLTAGE 3~36 Volt POWER 120 Watt FEATURES APPLICATIONS
SINGLE LINE TVS DIODE FOR ESD PROTECTION PORTABLE ELECTRONICS VOLTAGE 3~36 Volt POWER 120 Watt FEATURES 120 Watts peak pules power( tp=8/20μs) Small package for use in portable electronics Suitable replacement
MBR1040VL SURFACE MOUNT LOW FORWARD DROP SCHOTTKY BARRIER. VOLTAGE 40 Volt CURRENT 1 Amper FEATURES MECHANICAL DATA ABSOLUTE RATINGS
SURFAE MOUNT LOW FORWARD DROP SHOTTKY BARRIER VOLTAGE 40 Volt URRENT 1 Amper FEATURES Fast switching speed Surface mount package ideally suited for automatic insertion 0.115(2.90) 0.106(2.70) 0.075(1.90)
PJ3L85 DATA BUS TERMINATOR / 3-PHASE, FULL WAVE BRIDGE SOT-363 FEATURES APPLICATIONS MAXIMUM RATINGS THERMAL CHARACTERISTICS
DATA BUS TERMINATOR / 3PHASE, FULL WAVE BRIDGE This highly integrated device is designed as rail to rail overvoltage protection clamp for up to 3 data lines. It is also ideal as a threephase, full wave
MMBT4403 PNP GENERAL PURPOSE SWITCHING TRANSISTOR FEATURES MECHANICAL DATA ABSOLUTE MAXIMUM RATINGS THERMAL CHARACTERISTICS
PNP GENERAL PURPOSE SWITCHING TRANSISTOR VOLTAGE 40V POWER 225mW FEATURES PNP epitaxial silicon, planar design 0.120(3.04) 0.110(2.80) Collectoremitter voltage V CE = 40V Collector current I C =600mA Complimentary
ER2DAF SURFACE MOUNT RECTIFIER. VOLTAGE 200 Volts CURRENT 2 Amperes FEATURES MECHANICAL DATA
SURFACE MOUNT FEATURES RECTIFIER VOLTAGE 200 Volts CURRENT 2 Amperes Plastic package has Underwriters Laboratory Flammability Classification 94V-O For surface mounted applications Glass passivated junction
PBAT54-AU SERIES. SURFACE MOUNT SCHOTTKY DIODES Voltage 30 V Current 0.2 A. Features. Mechanical Data
SURFACE MOUNT SCHOTTKY DIODES Voltage 30 V Current 0.2 A SOT-23 Features Fast switching speed Surface mount package ideally suited for automatic insertion electrical identical standard JEDEC High conductor
PSX34-AU. SURFACE MOUNT LOW VF SCHOTTKY BARRIER RECTIFIER Voltage 40 V Current 3 A. Features. Mechanical Data
SURFACE MOUNT LOW VF SCHOTTKY BARRIER RECTIFIER Voltage 40 V Current 3 A Features Deal for automated placement Low power loss, high efficiency High surge current capability Lead free in compliance with
DUAL SURFACE MOUNT NPN/PNP TRANSISTORS (COMPLIMENTARY) Rating Symbol Value Units Collector-Base Voltage. 50 V Collector-Emitter Voltage
DUAL SURFACE MOUNT NPN/PNP TRANSISTORS (COMPLIMENTARY) This device contains two electrically-isolated complimentary pair (NPN and PNP) general-purpose transistors. This device is ideal for portable applications
20V N-Channel Enhancement Mode MOSFET ESD Protected PARAMETER SYMBOL LIMIT UNITS
20V N-Channel Enhancement Mode MOSFET ESD Protected Voltage 20 V Current 800mA SOT-523 Unit : inch(mm) Features R DS(ON), V GS@4.5V,I DS@500mA=0.4Ω R DS(ON), V GS@2.5V,I DS@300mA=0.7Ω R DS(ON), V GS@1.8V,I
PARAMETER SYMBOL LIMIT UNITS
20V P-Channel Enhancement Mode MOSFET ESD Protected SOT-23 Voltage -20 V Current -4.3A Unit : inch(mm) Features RDS(ON), VGS@-4.5V, ID@-4.3A
PPJW3P10A. 100V P-Channel Enhancement Mode MOSFET. Voltage -100 V Current -2.6 A. Features. Mechanical Data
100V P-Channel Enhancement Mode MOSFET Voltage -100 V Current -2.6 A Features SOT-223 R DS(ON), V GS @-10V,I D @-2.6A
BC846-AU,BC847-AU,BC848-AU,BC849-AU,BC850-AU SERIES
BC846-AU,BC847-AU,BC848-AU,BC849-AU,BC85-AU SERIES NPN GENERAL PURPOSE TRANSISTORS OLTAGE 3/45/65 olt POWER 33 mwatt FEATURES General purpose amplifier applications NPN epitaxial silicon, planar design
PARAMETER SYMBOL LIMIT UNITS
20V P-Channel Enhancement Mode MOSFET Voltage -20 V Current -4.0A Features RDS(ON), VGS@-4.5V, ID@-4.0A
V DD =30V, I D =200mA, Turn-On Rise Time tr V GS =10V, Turn-Off Delay Time td (off) (Note 1,2) R G =10Ω Turn-Off Fall Time tf
60V N-Channel Enhancement Mode MOSFET ESD Protected Voltage 60 V Current 300mA SOT-23 Unit : inch(mm) Features R DS(ON), V GS @10V, I D @500mA
PJSD05CW SERIES. Fig.130. Single Line TVS Diode for ESD Protection in Portable Electronics FEATURES MECHANICAL DATA ABSOLUTE MAXIMUM RATINGS
Single Line TS Diode for ESD Protection in Portable Electronics OLTAGE 5 to 36 olt POWER 35 Watt FEATURES Transient protection for data lines to IE 6-4-2 (ESD) + 15k (air),+ 8k (contact).78(1.95).68(1.75)
P6AF3.3A~P6AF64A. SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Voltage 3.3~64 V Power 600 W SMAF Unit: inch(mm) Features.
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Voltage 3.3~64 V Power 600 W SMAF Unit: inch(mm) Features For surface mounted applications in order to optimize board space. Ultra thin profile package for space
MMBT4401 NPN GENERAL PURPOSE SWITCHING TRANSISTOR. VOLTAGE 40 Volt POWER 225 mwatt FEATURES MECHANICAL DATA ABSOLUTE RATINGS THERMAL CHARACTERISTICS
NPN GENERAL PURPOSE SWITCHING TRANSISTOR VOLTAGE 40 Volt POWER 225 mwatt FEATURES NPN epitaxial silicon, planar design Collectoremitter voltage V CE = 40V 0.20(3.04) 0.0(2.80) 0.006(0.5)MIN. Collector
P6AF3.3A-AU~P6AF64A-AU
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Voltage 3.3~64 V Power 600 W SMAF Unit: inch(mm) Features For surface mounted applications in order to optimize board space. Ultra thin profile package for space
MMBT3904-AU NPN GENERAL PURPOSE SWITCHING TRANSISTOR. VOLTAGE 40 Volt POWER 225 mwatt FEATURES MECHANICAL DATA ABSOLUTE RATINGS
MMBT3904AU NPN GENERAL PURPOSE SWITCHING TRANSISTOR OLTAGE 40 olt POWER 225 mwatt FEATURES SOT23 Unit: inch(mm) NPN epitaxial silicon, planar design emitter voltage CE = 40 0.120(3.04) 0.110(2.80) current
Transient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Excellent
BZW04 SERIES Taiwan Semiconductor
W, 5.8V - 376V Transient Voltage Suppressor BZW4 SERIES FEATURES - Excellent clamping capability - Low impedance surge resistance - W surge capability at / μs waveform - Very fast response time - Typical
5 to 220 Volt DEVICES FOR BIPOLAR APPLICATIONS
SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR POWER 600 Watt STAND-OFF VOLTAGE 5 to 220 Volt Recongnized File # E210467 FEATURES For surface mounted applications in order to optimize board space Glass passivated
PSBT30100VYT ULTRA LOW VF SCHOTTKY BARRIER RECTIFIER. Voltage 100 V Current 30 A. Features. Mechanical Data
ULTRA LOW VF SCHOTTKY BARRIER RECTIFIER Voltage 100 V Current 30 A Features TO220AB Unit: inch(mm) Ultra low forward voltage drop, low power loss High efficiency operation Lead free in compliance with
P6KE SERIES Taiwan Semiconductor
600W, 6.8V - 440V Transient Voltage Suppressor FEATURES - Excellent clamping capability - Low dynamic impedance - 600W surge capability at 10 / 0 μs waveform - Fast response time: Typically less than 1.0ps
30KP Series 30000W AXIAL LEAD TRANSIENT VOLTAGE SUPPRESSOR R-6 PACKAGE WILLAS ELECTRONIC CORP. R-6 (Cathode band Only Uui-polarity product)
3W AXIAL LEAD TRANSIENT VOLTAGE SUPPRESSOR 3KP Series 1.(25.4)MIN..36(9.14).338(8.6) 1.(25.4)MIN. R-6 (Cathode band Only Uui-polarity product).52(1.32).47(1.2) Dimensions in inches and (millimeters) DIA..36(9.14).338(8.6)
P4KE SERIES Taiwan Semiconductor
400W, 6.8V - 440V Transient Voltage Suppressor FEATURES - Excellent clamping capability - Low dynamic impedance - 400W surge capability at 10 / 1000 μs waveform - Fast response time: Typically less than
SA SERIES Taiwan Semiconductor
500W, 5V - 170V Transient Suppressor FEATURES - Excellent clamping capability - Low dynamic impedance - 500W surge capability at 10 / 0 μs waveform - Fast response time: Typically less than 1.0ps from
Transient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features Glass passivated junction Low zener impedance Excellent clamping capability 400W peak pulse power capability at 10/1000μs waveform, repetition rate (duty
6600W, 10V 43V Surface Mount Transient Voltage Suppressor
66W, 1V 43V Surface Mount Transient Voltage Suppressor FEATURES AEC-Q11 qualified Junction passivation optimized design technology T J =175 C capability suitable for high reliability and automotive requirement
Distributed by: www.jameco.com 1-8-831-4242 The content and copyrights of the attached material are the property of its owner. P6KE6V8(C)A - P6KE4(C)A 6W TRANSIENT VOLTAGE SUPPRESSOR Features 6W Peak Pulse
BZW06 SERIES Taiwan Semiconductor
600W, 3V - 376V Transient Voltage Suppressor FEATURES - Excellent clamping capability - Low dynamic impedance - 600W surge capability at / 0 μs waveform - Fast response time: Typically less than.0ps from
SA Series. Working Voltage: 5.0 to 190 V Peak Pulae Power: 500 W 500W AXIAL LEAD TRANSIENT VOLTAGE SUPPRESSOR DO-15 PACKAGE
Working : 5.0 to 190 V Peak Pulae Power: 500 W Features Glass passivated chip 500 W peak pulse power capability with a 10/1000 μs waveform, repetitive rate (duty cycle):0.01 % Low leakage Uni and Bidirectional
Transient Voltage Suppression Diodes. Surface Mount 400W > P4SMA series. Features. less than 1μA when V BR. Applications. Additional Infomarion
P4SMA Series RoHS Pb e3 Uni-directional Bi-directional Description The P4SMA series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other
Surface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V WM (uni-directional) 5.8 V to 459 V V WM (bi-directional) 5.8 V to 185 V V BR (uni-directional) 6.8 V to 540 V V BR (bi-directional)
DATA SHEET TRANSIENT VOLTAGE SUPPRESSORS AC/DC POWER SUPPLY 1.0SMB series
Product specification November 5, 28 V. DATA SHEET TRANSIENT VOLTAGE SUPPRESSORS AC/DC POWER SUPPLY.SMB series RoHS compliant & Halogen free Transient Suppressors.SMB 2 Transient Suppressors (TVS) Data
Surface Mount Transient Voltage Suppressors (TVS)
Description The 1.5SMC series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional
High Temperature Stability and High Reliability Conditions FEATURES. PARAMETER SYMBOL VALUE UNIT with 10/1000 μs waveform Peak pulse power dissipation
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions PRIMARY CHARACTERISTICS V WM 1 V to 36 V V BR 11.1 V to 44.2 V P PPM (1 x 1 μs) 36 W P PPM (1
Single Pulsed (Note 4) E AS 1100 mj Repetitive (Note 5) E AR 29 mj Peak Diode Recovery dv/dt (Note 5) dv/dt 15 V/ns 290 TO-3PL P D 220
500V N-Channel MOSFET Voltage 500 V Current 24A Features: R DS(ON), @,I D@ 12.0A
General Purpose Plastic Rectifier
General Purpose Plastic Rectifier N400 thru N4007 DO-4AL (DO-4) MAJOR RATINGS AND CHARACTERISTICS I F(AV).0 A V RRM V to 00 V I FSM (8.3 ms sine-wave) A I FSM (square wave t p = ms) 45 A V F. V I R 5.0
SMB10J SERIES Taiwan Semiconductor
0W Surface Mount Transient Voltage Suppressor FEATURES - Low profile package - Ideal for automated placement - Glass passivated junction - Excellent clamping capability - Fast response time: typically
ICTE5 thru ICTE18C, 1N6373 thru 1N6386. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor.
TRANSZORB Transient Voltage Suppressors Case Style 1.5KE PRIMARY CHARACTERISTICS V WM 5. V to 18 V V BR (uni-directional) 6. V to 21.2 V V BR (bi-directional) 9.2 V to 21.2 V P PPM 1 W P D 6.5 W I FSM
MSP5.0A. Surface Mount TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. New Product
MSP5.A Surface Mount TRANSZORB Transient Voltage Suppressors esmp TM Series Top View Bottom View MicroSMP PRIMARY CHARACTERISTICS V WM 5. V P PPM W I FSM 25 A T J max. 5 C FEATURES Very low profile - typical
200W, 5V - 100V Surface Mount Transient Voltage Suppressor
200W, 5V - 100V Surface Mount Transient Voltage Suppressor FEATURES Photo Glass passivated junction Low power loss, high efficiency Ideal for automated placement Excellent clamping capability Typical I
High Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions DO-218 Compatible PRIMARY CHARACTERISTICS V BR 11.1 V to 52.8 V P PPM (1 x μs) 66 W P PPM (1 x
200W, 5V - 100V Surface Mount Transient Voltage Suppressor
200W, 5V - 100V Surface Mount Transient Voltage Suppressor FEATURES Photo Glass passivated junction Low power loss, high efficiency Ideal for automated placement Excellent clamping capability Typical I
Surface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors esmp Series PRIMARY CHARACTERISTICS V BR uni-directional 4. V to 44.2 V V WM 3.3 V to 36 V P PPM 400 W I FSM 40 A T J max. 150 C Polarity Uni-directional
Surface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V BR 6.8 V to 220 V V WM 5.8 V to 188 V P PPM 600 W P D 5.0 W I FSM (uni-directional only) A T J max. 150 C Polarity Uni-directional,
High Power Density Surface Mount TRANSZORB Transient Voltage Suppressors
High Power Density Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V BR 6.4 V to 49.1 V V WM 5.0 V to 40 V P PPM 0 W I FSM (uni-directional only) 40 A T J max. 1 C Polarity
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 400 WATT PEAK POWER 1.0 WATTS STEADY STATE SYMBOL IPPM P M(AV) I FSM. I 2 t 6.64 A 2 /Sec T J, T STG
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 4 WATT PEAK POWER 1. WATTS STEADY STATE TVS P4FMAJ SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 4
P4KE6.8A thru P4KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V WM 5.8 V to 459 V V BR uni-directional 6.8 V to 54 V V BR bi-directional 6.8 V to 44 V P PPM 4 W P D 1.5 W I FSM (uni-directional only)
Green. Part Number Qualification Case Packaging P4SMAJXXADF-13 Commercial D-FLAT 10,000/Tape & Reel
Green 400W SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Features Mechanical Data Packaged in the Low Profile D-FLAT to Optimize Board Space Case: D-FLAT Glass Passivated Die Construction Excellent Clamping
MSP3V3, MSP5.0A. Surface Mount TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES. Series.
Surface Mount TRANSZORB Transient Voltage Suppressors esmp Series Top View Bottom View PRIMARY CHARACTERISTICS V WM 3.3 V to 5. V V BR 4.1 V to 7.7 V P PPM 15 W T J max. 15 C Polarity Uni-directional Package
New Product. High Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions PRIMARY CHARACTERISTICS V WM 1 V to 43 V V BR 11.1 V to 52.8 V P PPM 3 W P D 6. W I FSM 2 A T
1SMA4737-1SMA200Z Taiwan Semiconductor
CREAT BY ART W, 7.5V - 200V Surface Mount Silicon Zener Diodes SMA4737 - SMA200Z FEATURES - Built-in strain relief - Ideal for automated placement - Glass passivated junction - Low inductance - Typical
Analogue instruments NEW ZEALAND
NEW ZEALAND WWW.LPINZ.CO.NZ Unit 6/22 Moselle Ave, Henderson, Auckland, New Zealand PO Box 21-872, Henderson, Auckland, New Zealand Phone:+64 9 833 5749 Email:info@LPINZ.co.nz Web: www.lpinz.co.nz Analogue
P4SMA-E Series. TVS Diodes Surface Mount 400W > P4SMA-E series Series. Description. Uni-directional
P4SMA-E Series RoHS Pb e3 Description The P4SMA-E series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
China - Germany - Korea - Singapore - United States - smc-diodes.com
TRANSIENT SUPPRESSOR Features DO-15 Glass Passivated Die Construction 600W Peak Pulse Power Dissipation 5.8V- 376V Standoff Voltage Uni- and Bi-Directional Versions Available Excellent Clamping Capability
ICTE5.0 THRU ICTE15C SERIES
ICTE5.0 THRU ICTE15C SERIES TRANSZORB TRANSIENT VOLTAGE SUPPRESSOR Stand-off Voltage - 5.0 to 15 Volts Peak Pulse Power - Watts Case Style 1.5KE 1.00 (25.4) MIN. 0.205 (5.207) 0.190 (4.826) DIA. 0.375
1.5SMCxxAT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMCxxAT3G. Cathode. Anode. Uni-directional. Description
1.5SMCxxAT3G Pb Description The 1.5SMCxxAT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability,
High Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions DO-28AB PRIMARY CHARACTERISTICS V BR 27 V P PPM ( x μs) 36 W P D 5 W V WM 22 V I RSM 7 A I FSM
5KP8.5A thru 5KP188A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES TYPICAL APPLICATIONS
TRANSZORB Transient Voltage Suppressors P6 PRIMARY CHARACTERISTICS V WM 8.5 V to 188 V V BR 9.4 V to 231 V P PPM 5 W P D 8. W I FSM 5 A T J max. 175 C Polarity Uni-directional Package P6 FEATURES P6 glass
M C C. SMCJ1.5KE6.8(C)A THRU SMCJ1.5KE550(C)A. Features. Transient Voltage Suppressor 6.8 to 550 Volts 1500 Watt.
omponents 20736 Marilla Street Chatsworth!"# $%!"# SMCJ1.5KE6.8(C)A THRU SMCJ1.5KE550(C)A Features For surface mount applicationsin in order tooptimize board space Lead Free Finish/Rohs Compliant (Note1)
P6KE6.8A thru P6KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors DO-204AC (DO-15) PRIMARY CHARACTERISTICS V WM 5.8 V to 459 V V BR uni-directional 6.8 V to 540 V V BR bi-directional 6.8 V to 440 V P PPM 600 W P D 5.0 W I FSM (uni-directional
High Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions PRIMARY CHARACTERISTICS V WM 1 V to 43 V V BR 11.1 V to 52.8 V P PPM 3 W P D 6. W I FSM 2 A T
SA5.0A thru SA170CA. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors DO-204AC (DO-15) PRIMARY CHARACTERISTICS V WM 5.0 V to 170 V V BR (uni-directional) 6.4 V to 209 V V BR (bi-directional) 6.4 V to 209 V P PPM 500 W P D 3.0 W I FSM