E2Q5. Square Proximity Sensor. Long Distance Square Inductive Proximity Sensor. Ordering Information

Transcription

1 ASH & ALAIN INDIA PVT LTD S-00, F.I.E.E., Okhla Industrial Area, Phase-ii, New Delhi-0020(India) Tel : Fax : sales@ashalain.com Long Distance Square Inductive Square M2 Plug-in connection Integrated short circuit and reverse polarity protection Active face positioning: Y-axis 5, X-axis 90 incremets Ordering Information 20 mm shielded 40 mm non-shielded Connection Plug-in connector Active face Changable Output + NC NPN -N20E-M -N20E-M PNP -N20F-M -N20F-M NPN -N40ME-M -N40ME-M PNP -N40MF-M -N40MF-M D-

2 Rating/performance shielded non-shielded Item Model -N20##-M -N40M#-M Sn 20 mm ± 0% 40 mm ± 0% Standard target size, L x W x H, Fe 7 60 x 60 x mm 20 x 20 x mm Setting 0 to 6,2 mm 0 to 2,4 mm Switching frequency 50 Hz Ferrous metals Differential travel 5% max. of Sn Operating voltage 0 to DC Current consumption 20 ma max. Control output Type -N###E-##:NPN - -N###E-##: NPN - + NC -N###F-##:PNP - -N###F-##: PNP - + NC 200 ma max. On-stage voltage drop VDC max. (at 200 ma load current) Circuit protection Reverse polarity, output short circuit Operating indicator (yellow LED), operating voltage (green LED) Ambient temperature Operating: -25 to 85 C Ambient humidity 5 to 95% RH Influence of temperature ± 0% max. of Sn at 2 in temperature range of -25 to 70 C Dielectric strength.50ac, 50/60 Hz for min. between current carry parts and case Electromagnetic compatibility EMC EN Vibration resistance 0 to 55 Hz, mm amplitude according IEC Shock resistance Approx. 0 G for ms according to IEC Protection degree IP67 IEC 60529, IP69K DIN Connection Connector M2 plug, 4 pins Material Case PBT face PBT Approvals CERTIFIED LISTED D-2 Inductive s

3 Output Circuit Diagramm NPN output Model mode Timing chart Output circuit -N20E-M -N40ME-M Non- zone zone Control output Note: Terminal 2 is not used -N20E-M -N40ME-M + NC Non- zone zone Control output Control output NC White NC D-

4 PNP output Model mode Timing chart Output circuit Non- zone zone -N20F-M -N40MF-M Control output Note: Terminal 2 is not used -N20F-M -N40MF-M + NC Non- zone zone White NC Control output Control output NC Dimensions (Unit:mm) -...-M type LED yellow LED green LED yellow M2 x LED green ø 5.5 D-4 Inductive s

5 Precautions! Caution Power supply Do not impose an exessive voltage on the E2Q2, otherwise it may explode or burn. Do not connect an AC power supply to any DC model. If AC power (0AC or more) is supplied to the sensor, it may explode or burn. Mutual Interference If more than one is located in parallel, ensure to tain enough space between adjacent s to suppress mutual interference as provided in the following diagram. Side-by-side A Incorrect Mutual Interference (Unit: mm) Model Length A -N20##-M 40 -N40M##-M 50 Be sure to abide by the following precautions for the safe operation of the. Wiring Power Supply Voltage and Output Power Supply Voltage Make sure that the power supply to the is within the rated voltage range. If a voltage exceeding the rated voltage range is supplied to the, it may explode or burn. Power Reset Time The is ready to operate within 00 ms after the is turned. If the load and are connected to independent power supplies respectively, be sure to turn the before supplying power to the load. Power The may output a pulse signal when it is turned. Therefore, it is recommended that the load be turned before turning the. Short-circuiting Do not short-circuit the load, otherwise the may be damaged. Power Supply Transformer When using a DC power supply, make sure that the DC power supply has an insulated transformer. Do not use a DC power supply with an auto-transformer. Connection without Do not connect the power supply to the with no load connected, otherwise the internal elements may explode or burn. Operating Environment Do not use the in locations with explosive or flammable gas. Correct Use Design Effects of Surrounding Metal Provide a minimum between the and the surrounding metal as shown in the table below. Object The of the vary with the metal coating on s. Wiring High-tension cables Wiring through Metal Conduit: If there is power or high-tension line near the cable of the, wire the cable through an independent metal conduit to prevent against damage or malfunction. B A Effects of Surrounding Metal (Unit: mm) Model Length A B C -N20##-M N40M##-M C D-5

6 Long Distance Square Inductive M2 Plug-in connection Integrated short circuit and reverse polarity protection Active face positioning: Y-axis 5, X-axis 90 incremets ASH & ALAIN INDIA PVT LTD S-00, F.I.E.E., Okhla Industrial Area, Phase-ii, New Delhi-0020(India) Tel : Fax : sales@ashalain.com Square Ordering Information 20 mm shielded 40 mm non-shielded Connection Plug-in connector Active face Changable Output + NC NPN -N20E-M -N20E-M PNP -N20F-M -N20F-M NPN -N40ME-M -N40ME-M PNP -N40MF-M -N40MF-M ASH & ALAIN INDIA PVT LTD S-00, F.I.E.E., Okhla Industrial Area, Phase-ii, New Delhi-0020(India) Tel : Fax : sales@ashalain.com D-