Encoder - Absolut 2RMHF-SSI

Size: px
Start display at page:

Download "Encoder - Absolut 2RMHF-SSI"

Transcription

1 Absolute Encoder: Ø24 mm Hollow Shaft: Ø3 mm to ¼ Inch Singleturn or Multiturn SSI Interface Binary or Gray Code Preset of Zero Position Choice of Counting Direction IP-Rating: IP64 or IP67 Mechanical Data Weight: Encoder ~55 g (1,94 oz) 50 g / meter (1,76 oz / meter) Material: Housing Hollow Shaft Cap Brass Brass Electroplated Steel or Aluminium Connection 8-leads (0,05 mm 2, 30 AWG); Twisted Pair shielded M9; 8-pin / M12; 8-pin Bearing Life > 1,9 x revolutions (rated load) Shaft Loads axial < 20 N (4,5 lbs) radial < 20 N (4,5 lbs) Shaft Speed < rpm Starting Torque < 0,005 Nm (0,708 oz-in) at 25 C Mass Moment of Inertia 1,05 gcm 2 (1,49 x 10-5 oz-in-sec 2 ) Operating Temperature -40 C to +85 C Storage Temperature -40 C to +85 C Shock 100 G / 11 ms Vibration Hz / 10 G Bump 10 G / 16 ms (1.000 x 3 axis) Humidity 98% RH without condensation IP-Rating IP64 / Nema 4 (approx.) IP67 / Nema 6 (approx.) Page 1 to 5

2 Electrical Data Code Absolut 13 bits (8.192) points per revolution 12 bits (4.096) revolutions Resolution 16 bits (65.536) revolutions 20 bits ( ) revolutions 24 bits ( ) revolutions Supply Voltage 5 VDC ±5% Typical Current Consumption 30 ma (no load) Accuracy ± 0,35 Interface SSI (Synchronous Serial Interface) Output Code Binary or Gray Electrical Interface Differential (RS422) or Single ended (TTL) Clock Frequency 100 khz to 1 MHz Counting Direction Increasing clockwise or increasing counter clockwise seen from shaft end of encoder Electrical Protection Reverse polarity and output short circuit protected Tested to EN : 2005 (industrial environments) Noise Immunity Electromagnetical compatibility (EMC) and EN : 2007 (residential, commercial, and light-industrial environments) for Electromagnetic compatibility (EMC) Assignment 8-leads M9; 8-pin M12; 8-pin Differential Differential Single Ended Signal Wire Color Pin Number CLK+ green 3 3 CLK- yellow 4 - DO+ gray 5 5 DO- pink 6 - Direction red 8 8 Preset blue 7 7 V sup brown 2 2 GND white 1 1 Shield Shield must be connected to connector housing connected to case ground Page 2 to 5

3 Interface msb = Most Significant Bit lsb = Least Significant Bit t C = Clock Period = 1 to 10 µsec. (100 khz to 1 MHz) t 1 = Clock High = 50% ± 15% of Clock Period t 2 = Clock Low = 50% ± 15% of Clock Period t D = Clock to Data Valid = < 100 nsec. t M = Monoflop Time = 20 ± 3 µsec. Implementation During the initial set-up and installation of the encoder, it is possible to set the direction of rotation and preset the encoder to zero. Setting of Direction The connection designated Direction is used to set the direction of rotation. If the line is open or connected to Vsup, the value will increase when the shaft is rotated clockwise when seen from the shaft end. If the line is connected to GND the value will increase when the shaft is rotated counter clockwise when seen from the shaft end. Notice, that the encoder must not be powered when the direction of rotation is set / changed. Notice also, that the encoder will change its position value when the direction of rotation is changed. Preset to Zero The connection designated Preset is used to preset the encoder zero. If the line is open or connected to Vsup, the encoder will not be preset to zero. If the line is connected to GND, the encoder will be preset to zero. The encoder will be held at zero as long as the line is connected to GND, even though the shaft is turned. The line must be connected to GND for at least 100 msec. for the preset to take effect. The new zero point will be stored permanently in the encoder. Notice, that the encoder must be powered when it is preset to zero. Page 3 to 5

4 Dimensions Standard Gland M9 M12 Page 4 to 5

5 Ordering Example Type B - D S - M9/8 - S1 Resolution Multiturn 1213 = 12 bits revolutions 1613 = 16 bits revolutions 2013 = 20 bits revolutions 2413 = 24 bits revolutions Singleturn 0013 = Steps/Revolution 13 bits Code B G = Binary = Gray Electrical Interface D = Differential (RS422) S = Single Ended (TTL) Hollow Shaft Diameter - Length = 3mmx 13mm* = 4mm x 13mm = 5mm x 13mm = 6mm x 13mm ⅛-13 = ⅛ in x 13mm* 3 / = 3 / 16 in x 13mm* ¼-13 = ¼ in x 13mm IP-Rating 64 = IP64 67 = IP67 Length [m] Standard 01 = Standard is 1 meter SF = Specific length 00 = no cable Takeout S = Side (radial) M9/8 = M9; 8-pin* M12/8 = M12; 8-pin 00 = no connector Spring Coupling S1 = 3 holes p/n S2 = 2 holes p/n S3 = 2 holes p/n S4 = 1 hole p/n = no spring coupling *not on stock Page 5 to 5

Material: Weight: Shaft Loads:

Material: Weight: Shaft Loads: Absolute Encoder Type SCA36NA-SSI Absolute Encoder - Ø 36 mm Shaft - Ø 6 mm Singleturn or Multiturn SSI Interface Binary or Gray Code Preset of Zero Position Choice of Counting Direction Enclosure Rating

More information

Oil & Gas / Heavy Industry Type 2REX-A-NA-SSI

Oil & Gas / Heavy Industry Type 2REX-A-NA-SSI Oil & Gas / Heavy Industry Type 2REX-A-NA-SSI EN 60079 Electrical Specifications Encoder Type: Singleturn Resolution: Number of Revolutions: Supply Voltage: Typical Current Consumption: Accuracy: ± 0,35ᴼ

More information

Material: Weight: Bearing Life: Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads:

Material: Weight: Bearing Life: Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads: Shaft Encoder - Ø 50 mm Shaft: Ø 6 mm to Ø 12 mm Resolution up to 12.500 ppr IP 65 (IP 67 option) Formerly named 2R or 2R-3L Automation / Electrical Specifications Code: Resolution: Supply Voltage: Voltage:

More information

Technical data. General specifications. Linearity error ± 0.1 Electrical specifications Operating voltage U B

Technical data. General specifications. Linearity error ± 0.1 Electrical specifications Operating voltage U B Model Number SYNCHRON SERIELLES INTERFACE Features Very small housing Up to 32 Bit multiturn SSI interface Free of wear magnetic sampling High resolution and accuracy Description The ENA36IL series are

More information

Technical data. General specifications V DC Power consumption P 0. 1 W Time delay before availability t v

Technical data. General specifications V DC Power consumption P 0. 1 W Time delay before availability t v Model Number SYNCHRON SERIELLES INTERFACE Features Very small housing Up to 32 Bit multiturn SSI interface Free of wear magnetic sampling High resolution and accuracy Description The ENA36IL series are

More information

DATASHEET ABSOLUTE MAGNETIC ROTARY ENCODER SSI

DATASHEET ABSOLUTE MAGNETIC ROTARY ENCODER SSI Robust rotary sensor based on reliable magnetic technology. Stainless steel housing capable to withstand extreme environmental conditions. Ideal suited for outdoor applications. Sturdy ball bearings for

More information

Absolute encoders - SSI

Absolute encoders - SSI with through hollow shaft Features Encoder multiturn / SSI Optical sensing method Resolution: singleturn 14 bit, multiturn 12 bit Compact design Cost-efficient mounting High reliability by self-diagnostics

More information

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders up to 14 bit ST / 16 bit MT

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders up to 14 bit ST / 16 bit MT Features Encoder multiturn / SSI Optical sensing method Resolution: max. singleturn 14 bit, multiturn 16 bit Clamping or synchro flange Electronic setting of zero point Counting direction input Available

More information

Multiturn absolute encoder

Multiturn absolute encoder SYNCHRON SERIELLES INTERFACE Multiturn absolute encoder Model Number Features Industrial standard housing Ø58 mm 30 Bit multiturn Data transfer up to 2 MBaud Optically isolated RS 422 interface Recessed

More information

Technical data. General specifications. Linearity error ± 0.1 Functional safety related parameters MTTF d 700 a at 40 C Mission Time (T M ) L 10

Technical data. General specifications. Linearity error ± 0.1 Functional safety related parameters MTTF d 700 a at 40 C Mission Time (T M ) L 10 Model Number SYNCHRON SERIELLES INTERFACE Features Recessed hollow shaft SSI interface Up to Bit multiturn Free of wear magnetic sampling High resolution and accuracy Additionally push buttons for preset

More information

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders up to 14 bit ST / 16 bit MT

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders up to 14 bit ST / 16 bit MT Features Encoder multiturn / SSI Optical sensing method Resolution: max. singleturn 14 bit, multiturn 16 bit Clamping or synchro flange Electronic setting of zero point Counting direction input Available

More information

Absolute encoders - SSI Shaft with clamping or synchro flange Optical multiturn encoders 14 bit ST / 12 bit MT

Absolute encoders - SSI Shaft with clamping or synchro flange Optical multiturn encoders 14 bit ST / 12 bit MT Features Encoder multiturn / SSI Optical sensing Resolution: singleturn 14 bit, multiturn 12 bit Clamping or synchro flange Electronic setting of zero point Counting direction input Suitable for high positive,

More information

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders 18 bit ST / 12 bit MT

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders 18 bit ST / 12 bit MT Features High resolution encoder multiturn / SSI Optical sensing method Resolution: singleturn 18 bit, multiturn 12 bit Electronic setting of zero point Counting direction input Available with additional

More information

Technical data. General specifications. Linearity error ± 0.1 Functional safety related parameters MTTF d 700 a at 40 C Mission Time (T M ) L 10

Technical data. General specifications. Linearity error ± 0.1 Functional safety related parameters MTTF d 700 a at 40 C Mission Time (T M ) L 10 Model Number SYNCHRON SERIELLES INTERFACE Features Solid shaft SSI interface Up to Bit multiturn Free of wear magnetic sampling High resolution and accuracy Additionally push buttons for preset function

More information

Multiturn absolute encoder

Multiturn absolute encoder SYNCHRON SERIELLES INTERFACE Multiturn absolute encoder Release date: 2016-07-12 16:14 Date of issue: 2016-07-12 t4917_eng.xml Model Number Features Industrial standard housing Ø58 mm 0 Bit multiturn Data

More information

Multiturn absolute encoder

Multiturn absolute encoder 0102 Model Number SYNCHRON SERIELLES INTERFACE Features Up to 30 Bit multiturn ATEX approval IECEx approval Flameproof enclosure Removable connection cap Galvanically isolated RS 22 interface Description

More information

ABSOLUTE ROTARY ENCODER SSI

ABSOLUTE ROTARY ENCODER SSI Main Features - Compact and heavy-duty industrial model - Interface: Synchronous-serial (RS422/485) - Housing: 58 mm - Shaft: 6 or 10 mm - Resolution: Max. 25 Bit =,554,42 steps over 4,096 revolutions

More information

Express Delivery. Axial. Connection

Express Delivery. Axial. Connection HIGH RESOLUTION INCREMENTAL SOLID SHAFT ENCODER FOR INDUSTRIAL APPLICATIONS Resolution up to 50.000 pulses per turn External diameter 58 mm Shaft from Ø 6 to 12 mm Protection class IP67 according to DIN

More information

ABSOLUTE MAGNETIC ROTARY ENCODER ANALOG

ABSOLUTE MAGNETIC ROTARY ENCODER ANALOG High-resolution absolute encoder based on magnetic technology. Singleturn sensing based on 360 Hall effect technology. Multiturn sensing based on magnetic pulse counter. No batteries used. Main Features

More information

Magnetic absolute single-turn encoder BMSH MAGRES parallel

Magnetic absolute single-turn encoder BMSH MAGRES parallel Magnetic absolute single-turn encoder BMSH MAGRES parallel features robust single-turn encoder up to 9 bit parallel interface miniature housing zero-point programmable general data voltage supply 5 VDC

More information

Technical data. General specifications. Measurement range min max. 360

Technical data. General specifications. Measurement range min max. 360 Model Number Features Very small housing High climatic resistance 12 Bit singleturn Analog output Surge and reverse polarity protection Description This absolute rotary encoder with internal magnetic sampling

More information

Incremental encoders Blind or through hollow shaft ø12 mm pulses per revolution

Incremental encoders Blind or through hollow shaft ø12 mm pulses per revolution Blind or through hollow shaft ø mm...5 pulses per revolution Features Encoder with blind or through hollow shaft ø mm Optical sensing method Max. 5 pulses per revolution Small profile depth Versatile mounting

More information

Technical data. General specifications V DC No-load supply current I 0. typ. 50 ma Power consumption P 0

Technical data. General specifications V DC No-load supply current I 0. typ. 50 ma Power consumption P 0 Model Number SYNCHRON SERIELLES INTERFACE Cable pull rotary encoder with SSI interface Features Solid yet lightweight plastic construction Compact, slim design (the shaft of the mounted rotary encoder

More information

DS-70. Absolute position, rotary Electric Encoder

DS-70. Absolute position, rotary Electric Encoder DS-70 Data Sheet, V 2.0,Nov. 2012 DS-70 Absolute position, rotary Electric Encoder The DS-70 is a member of the DS series of Electric Encoders, based on Netzer Precision proprietary technology. These encoders

More information

NOVOHALL Rotary Sensor non-contacting. Series RSC2800 digital SSI, SPI, Incremental

NOVOHALL Rotary Sensor non-contacting. Series RSC2800 digital SSI, SPI, Incremental NOVOHALL Rotary Sensor non-contacting Series RSC2800 digital SSI, SPI, Incremental The RSC 2800 sensor utilizes a contactless magnetic measurement technology to determine the measured angle. Unlike conventional

More information

DS-58[20] Absolute position, rotary Electric Encoder

DS-58[20] Absolute position, rotary Electric Encoder DS-58[20] Data Sheet, V 2.0b,June. 2013 DS-58[20] Absolute position, rotary Electric Encoder The DS-58[20] is a member of the DS series of Electric Encoders, based on Netzer Precision proprietary technology.

More information

Magnetic absolute multi-turn hollow shaft encoder BMMH MAGRES SSI

Magnetic absolute multi-turn hollow shaft encoder BMMH MAGRES SSI Magnetic absolute multi-turn hollow shaft encoder BMMH MAGRES SSI features robust multi-turn encoder up to - 2 bit single-turn resolution - 3 bit multi-turn resolution miniature housing zero point programmable

More information

DS-25. Absolute position, rotary Electric Encoder

DS-25. Absolute position, rotary Electric Encoder Data Sheet, V 2.0,NOV 2012 Absolute position, rotary Electric Encoder The is a member of the DS series of Electric Encoders, based on Netzer Precision proprietary technology. These encoders offer many

More information

IXARC Incremental Encoder UCD-IPT M100-PRD. Interface Programmable Incremental. Configuration Tool UBIFAST Configuration Tool (Version 1.6.

IXARC Incremental Encoder UCD-IPT M100-PRD. Interface Programmable Incremental. Configuration Tool UBIFAST Configuration Tool (Version 1.6. IXARC Incremental Encoder UCD-IPT00-08192-M100-PRD Interface Interface Programmable Incremental Programming Functions PPR (1-16384), Output, Counting Direction Configuration Tool UBIFAST Configuration

More information

MHAD 50 - HDmag. Features

MHAD 50 - HDmag. Features Magnetic sensing, hollow shaft 30 mm MHAD 50 with cable Features Absolute encoder with magnetic sensing and without bearings Absolute resolution max. 16 bit singleturn Additional incremental signals Robust

More information

ABSOLUTE ROTARY ENCODER DEVICE NET

ABSOLUTE ROTARY ENCODER DEVICE NET Main Features - Compact and heavy-duty industrial model - Certified: By ODVA - Interface: Device Net - Housing: 58 mm - Full or hollow shaft: 6 or 0 mm / 5 mm - Max. 6556 steps per revolution (6 Bit) -

More information

ABSOLUTE ROTARY ENCODER SSI PROGRAMMABLE

ABSOLUTE ROTARY ENCODER SSI PROGRAMMABLE Main Features - Compact and heavy-duty industrial model - Interface: Synchronous-serial (RS422/485) - Housing: 58 mm - Shaft: 6 or 10 mm - Resolution: Max. 25 Bit =,554,42 steps over 4,096 revolutions

More information

Absolute Encoders Multiturn

Absolute Encoders Multiturn The Sendix F36 multiturn with the patented Intelligent Scan Technology is an optical multiturn encoder in miniature format, without gears and with 00% insensitivity to magnetic fields. With a size of just

More information

ABSOLUTE ROTARY ENCODER MULTI-TURN BIT PARALLEL

ABSOLUTE ROTARY ENCODER MULTI-TURN BIT PARALLEL Main Features - Compact and heavy-duty industrial model - Interface: Bit-parallel, push pull ΠShort circuit proof - Housing: 58 mm - Shaft: 6 or 10 mm - Resolution: Max. 25 Bit =,554,42 steps over 4,096

More information

ABSOLUTE ROTARY ENCODER SSI

ABSOLUTE ROTARY ENCODER SSI Main Features - Compact and heavy-duty industrial model - Interface: Synchronous-serial (RS 422) - Housing: 58 mm - Shaft: 6 or 10 mm - Hollow shaft 12 mm - Blind hollow shaft 15 mm - Max. 65,56 steps

More information

MODEL S15 Incremental Optical Rotary Encoder

MODEL S15 Incremental Optical Rotary Encoder MODEL S15 Incremental Optical Rotary Encoder Up to 200 KHz frequency response all channels Small compact size: 1.51 diameter 1.00 dia. Bolt circle mount Resolutions up to 12,500 cycles / revolution ( 50,000

More information

ABSOLUTE MAGNETIC ROTARY ENCODER ANALOG

ABSOLUTE MAGNETIC ROTARY ENCODER ANALOG High-resolution absolute encoder via magnetic technology. Singleturn encoding based on 360 Hall effect technology. Multiturn encoding based on magnetic pulse counter. No batteries used. Main Features -

More information

Absolute encoders - analog Blind hollow shaft ø12 mm Magnetic single- or multiturn encoders 12 bit ST / 16 bit MT

Absolute encoders - analog Blind hollow shaft ø12 mm Magnetic single- or multiturn encoders 12 bit ST / 16 bit MT Blind hollow shaft ø mm Magnetic single- or multiturn encoders bit ST / bit MT BMSH 8, BMMH 8 analog - MAGRES Features Encoder single- or multiturn / analog Magnetic sensing Resolution: singleturn bit,

More information

ABSOLUTE ROTARY ENCODER SSI

ABSOLUTE ROTARY ENCODER SSI Main Features - Compact and heavy-duty industrial model - Interface: Synchronous -serial (RS 422) - Housing: 58 mm - Shaft: 6 or 10 mm - Hollow shaft 12 mm - Blind hollow shaft 15 mm - Max. 65,56 steps

More information

Incremental encoders With blind or through hollow shaft pulses per revolution programmable

Incremental encoders With blind or through hollow shaft pulses per revolution programmable Features Size ø58 mm Precise optical sensing Output signal level programmable (TTL or HTL) Blind or through hollow shaft, ø8 15 mm Connection axial, radial or tangential Pulses per revolution 1...65536,

More information

Diameter ø50mm Shaft type Absolute Multi-turn Rotary Encoder

Diameter ø50mm Shaft type Absolute Multi-turn Rotary Encoder Dia ø50mm Shaft type Absolute Multi-turn otary Encoder Features Compact size of dia ø50mm Parallel data / SSI data transmission type Total 23bit resolution(8388608 divisions) of 10bit single-turn(1024

More information

Absolute multi-turn hollow shaft encoder BOMH Dignalizer SSI

Absolute multi-turn hollow shaft encoder BOMH Dignalizer SSI features high resolution multi-turn encoder up to - 8 bit single-turn - 8 bit multi-turn interface programmable permanent self-test reference point programmable general data voltage supply 5 VDC (05C)

More information

Absolute Encoders - Singleturn

Absolute Encoders - Singleturn The Sendix 5853 and Sendix 5873 singleturn encoders with SSI or BiSS interface and optical sensor technology can achieve a resolution of max. 7 bits. These encoders are also available with an optional

More information

Features & Benefits 360, 512, 720, 1000, 1024, 1440, 1800, 2000, 2048, 2880, 3000, 3600, 4000, 4096, 5000, 5120, 6000, 7200, 8000, 8192, 9000, 10000

Features & Benefits 360, 512, 720, 1000, 1024, 1440, 1800, 2000, 2048, 2880, 3000, 3600, 4000, 4096, 5000, 5120, 6000, 7200, 8000, 8192, 9000, 10000 CP-800/900 Series Size-25 Housed Rotary Optical Encoders Solid or hollow shaft, incremental, sine/cosine, or absolute format Allied Motion s CP800/900 series are size-25 (2.5 in. (63.5mm)) rotary optical

More information

LENORD. +BAUER... automates motion. GEL 2037 with heavy duty flange or tooth wheel adapter. Technical information Version General.

LENORD. +BAUER... automates motion. GEL 2037 with heavy duty flange or tooth wheel adapter. Technical information Version General. GEL 2037 with heavy duty flange or tooth wheel adapter LENORD +BAUER... automates motion. Technical information Version 2014-07 General Multiturn absolute rotary encoders with a resolution of up to 25

More information

Absolute Encoders Multiturn

Absolute Encoders Multiturn Absolute Encoders Multiturn Functional Safety, optical The absolute multiturn encoders Sendix 5863 SIL and 5883 SIL are perfectly suited for use in safety-related applications up to SIL3 according to DIN

More information

Absolute encoders - SSI EX approval ATEX EEx d IIC T6 Optical single and multiturn encoders 14 bit ST / 12 bit MT

Absolute encoders - SSI EX approval ATEX EEx d IIC T6 Optical single and multiturn encoders 14 bit ST / 12 bit MT Features Encoder single- or multiturn / SSI / ATEX Optical sensing Resolution: singleturn 14 bit, multiturn 12 bit Clamping flange with shaft ø10 mm Explosion protection per EEx d IIC T6 Area of application:

More information

Magnetic absolute rotary encoder GEL 235 Singleturn, Multiturn up to 28 bits (SSI)

Magnetic absolute rotary encoder GEL 235 Singleturn, Multiturn up to 28 bits (SSI) Magnetic absolute rotary encoder GEL 25 Singleturn, Multiturn up to 28 bits (SSI) Technical information version 09.06 Unique Nonius-evaluation Measuring principle: magnetic, high resolution Evaluation:

More information

NOVOTURN Multiturn Sensor non-contacting. Series RSM-2800

NOVOTURN Multiturn Sensor non-contacting. Series RSM-2800 NOVOTURN Multiturn Sensor non-contacting Series RSM-2800 Special features Non-contacting, magnetic Long life Electrical range 720 up to 5760 in 360 -steps available (2 to 16 turns) True-Power-On System:

More information

Absolute Encoders Singleturn

Absolute Encoders Singleturn The absolute singleturn encoders Sendix 5853 SIL and 5873 SIL are perfectly suited for use in safety-related applications up to SIL3 according to DIN EN ISO 6800-5- or PLe to DIN EN ISO 3849. The extra

More information

Rotary Measurement Technology Absolute Encoders, Multiturn

Rotary Measurement Technology Absolute Encoders, Multiturn Mechanical drive Safety-LockTM High rotational speed -40 to 90 C IP Temperature High IP High shaft load capacity Shock/ vibration resistant Magnetic field proof Short-circuit proof Reverse polarity protection

More information

Online data sheet AFS60E-S1AA AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFS60E-S1AA AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FS0E-S0009 FS/FM0 SSI SOLUTE ENCODERS FS0E-S0009 FS/FM0 SSI SOLUTE ENCODERS C D E F Ordering information Type Part no. FS0E-S0009 0 Other models and accessories www.sick.com/fs_fm0_ssi

More information

Absolute Encoders - Singleturn

Absolute Encoders - Singleturn The Sendix 5 and Sendix 7 singleturn encoders with SSI or BiSS-C interface and optical sensor technology can achieve a resolution of max. 7 bits. These encoders are also available with an optional SinCos

More information

Incremental Encoder Model: FOI58

Incremental Encoder Model: FOI58 Incremental Encoder Model: FI58 Document no. FI 188 BE Date: 1.01.201 Robust mechanical construction, high vibration and shock resistance 1 to 16,8 pulses/ revolution perating temperature - 0 C to + 85

More information

Incremental encoders With blind or through hollow shaft pulses per revolution programmable

Incremental encoders With blind or through hollow shaft pulses per revolution programmable Features Size mm Precise optical sensing Output signal level programmable (TTL or HTL) Blind or through hollow shaft, ø8 15 mm Connection axial, radial or tangential Pulses per revolution 1...65536, programmable

More information

Electrical data Units FVS 58, FHS 58. Operating voltage (PELV) [VDC] Current consumption at 24 VDC [ma] 85

Electrical data Units FVS 58, FHS 58. Operating voltage (PELV) [VDC] Current consumption at 24 VDC [ma] 85 Parallel Singleturn bsolute Value Encoder Features 13-bit Singleturn High code change frequency Inputs for: - Selection of counting direction - Buffer memory (LTCH) - Multiplex operation (TRISTTE) Short-circuit

More information

Online data sheet AFS60A-BJPA AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFS60A-BJPA AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FS0-JP FS/FM0 SSI FS0-JP FS/FM0 SSI C D E F H I J K L M N O P Q R S T Ordering information Type Part no. FS0-JP 09 Other models and accessories www.sick.com/fs_fm0_ssi Illustration may

More information

Resolution 0.03 % ( ); 0.1 % ( ) Repeatability ±0.03 % ( ); ±0.1 % ( )

Resolution 0.03 % ( ); 0.1 % ( ) Repeatability ±0.03 % ( ); ±0.1 % ( ) PRAS1 Magnetic Angle Sensor with Analog Output Magnetic angle 0-360 in M12 housing Measurement range 0 to 360 Protection class IP67 / IP69K Analog output Stainless steel housing Non-contact with external

More information

LENORD. +BAUER... automates motion. Magnetic absolute rotary encoder GEL 2037 with heavy duty flange or tooth wheel adapter

LENORD. +BAUER... automates motion. Magnetic absolute rotary encoder GEL 2037 with heavy duty flange or tooth wheel adapter Magnetic absolute rotary encoder GEL 2037 with heavy duty flange or tooth wheel adapter LENORD +BAUER... automates motion. Technical information Version 01.12 General Multiturn absolute rotary encoders

More information

Rotary Measuring Technology

Rotary Measuring Technology SSI or parallel interface Highest shock resistance on the market ( 2500 m/s2, 6 ms acc. to DIN IEC 68-2-27) Divisions: up to 16384 (14 bits), singleturn Housing Ø 58 mm IP 66 Various options (e.g. LATCH,

More information

Resolution 0.03 % ( ); 0.1 % ( ) Repeatability ±0.03 % ( ); ±0.1 % ( )

Resolution 0.03 % ( ); 0.1 % ( ) Repeatability ±0.03 % ( ); ±0.1 % ( ) PRAS1 Magnetic Angle Sensor with Analog Output Magnetic angle 0-360 in M12 housing Measurement range 0 to 360 Protection class IP67 / IP69K Analog output Stainless steel housing Non-contact with external

More information

Technical data. Functional safety related parameters MTTF d Mission Time (T M ) max. 140 ma Power consumption P 0. Voltage drop

Technical data. Functional safety related parameters MTTF d Mission Time (T M ) max. 140 ma Power consumption P 0. Voltage drop Release date: 2014-04-14 15: Date of issue: 2016-05-0 t102_eng.xml Model Number Features Industrial standard housing Ø58 mm 1 Bit singleturn Output code: gray and binary Short-circuit proof push-pull output

More information

Online data sheet. ACM60B-S1KE13x06 ACM60 ABSOLUTE ENCODERS

Online data sheet. ACM60B-S1KE13x06 ACM60 ABSOLUTE ENCODERS Online data sheet ACM60B-S1KE1x06 ACM60 A B C D E F H I J K L M N O P Q R S T Illustration may differ Detailed technical data Performance Number of steps per revolution Number of revolutions Ordering information

More information

847H. Description. Features. Specifications

847H. Description. Features. Specifications 847H Bulletin 847H High Performance Industrial Incremental Encoders provide code disk resolutions of up to 65536 pulses per revolution at a signal frequency response of 820 khz. The 847H can provide 65536

More information

Rotary encoders. absolute / optical. Bright ideas in the measurement of rotation: robust, precise, versatile.

Rotary encoders. absolute / optical. Bright ideas in the measurement of rotation: robust, precise, versatile. Rotary encoders absolute / optical right ideas in the measurement of rotation: robust, precise, versatile. Absolute encoder WK02/1 Hollow shaft WK02/1 - robust single-turn angle encoder with through hollow

More information

Incremental Shaft Encoders Industrial types

Incremental Shaft Encoders Industrial types Synchro flange! Universal industry standard encoder! Up to 40,000 steps with 10,000 pulses! High signal accuracy! Protection class up to IP 67! Operating temperature up to 100 C (RI 58-T)! Flexible due

More information

Diameter Ø50mm Shaft Type Magnetic Multi-Turn Absolute Rotary Encoder MGAM50S B F PN 24

Diameter Ø50mm Shaft Type Magnetic Multi-Turn Absolute Rotary Encoder MGAM50S B F PN 24 Ø0mm Shaft Magnetic Multi-Turn Absolute Type Diameter Ø0mm Shaft Type Magnetic Multi-Turn Absolute otary Encoder Features Higher resistant to vibration and impact by magnetic elements than optical encoder

More information

Online data sheet AFS60E-S4AC AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFS60E-S4AC AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FS60E-S4000256 FS/FM60 SSI FS60E-S4000256 FS/FM60 SSI D E F Ordering information Type Part no. FS60E-S4000256 1052119 Other models and accessories www.sick.com/fs_fm60_ssi Illustration

More information

TECHNICAL DATASHEET Absolute Encoder AC 58 - BiSS / SSI

TECHNICAL DATASHEET Absolute Encoder AC 58 - BiSS / SSI Compact design: 50 mm length for single or multiturn Aids for start up and operation: diagnostic LED, preset key with optical response, status information Use of sine/ cosine signals for fast control task

More information

Universal Radius Mounting Option. Fixed Radius Mounting Option

Universal Radius Mounting Option. Fixed Radius Mounting Option F e a t u r e s Factory Set for Same Day Dispatch (1 to 65,536 Pulses Per Rev) 100 Degrees Centegrate cabability as standard Opto-ASIC Technology Any bore - up to 15mm bore (Metric) or (Imperial) The 60HA

More information

JR12 Jam Nut Mount Optical Encoder

JR12 Jam Nut Mount Optical Encoder Improving the Quality of Life through the Power in Light JR12 Jam Nut Mount Optical Encoder QPhase Design Features: Replaces Size 15 Pancake Resolver Bearing design simplifies encoder attachment Resolutions

More information

DRS61: Incremental encoders, number of lines and zero pulse width freely programmable DRS60: Incremental Encoders with Zero-Pulse-Teach

DRS61: Incremental encoders, number of lines and zero pulse width freely programmable DRS60: Incremental Encoders with Zero-Pulse-Teach NEW DRS: Incremental encoders, number of lines and zero pulse width freely programmable DRS: s with Zero-Pulse-Teach Further highlights of this generation of encoders: Simple zero-pulse-teach by pressing

More information

Incremental encoders Redundant sensing, isolated blind hollow shaft ø mm, cone shaft ø17 mm pulses per revolution

Incremental encoders Redundant sensing, isolated blind hollow shaft ø mm, cone shaft ø17 mm pulses per revolution Features Robust, compact housing Two bearings with large distance, one at each end High shaft load up to 450 N Shock resistant up to 250 g Shaft insulation up to 2.8 kv Highest operating speed 10000 rpm

More information

Online data sheet AFM60B-S4PC AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFM60B-S4PC AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FM60-S4PC032768 FS/FM60 SSI C D E F H I J K L M N O P Q R S T Ordering information Type Part no. FM60-S4PC032768 1037504 Other models and accessories www.sick.com/fs_fm60_ssi Illustration

More information

Online data sheet DFS60B-S4PA00S74 DFS60 INCREMENTAL ENCODERS

Online data sheet DFS60B-S4PA00S74 DFS60 INCREMENTAL ENCODERS Online data sheet DFS60B-S4PA00S74 DFS60 A B C D E F Illustration may differ Ordering information Type Part no. DFS60B-S4PA00S74 1081183 Other models and accessories www.sick.com/dfs60 H I J K L M N O

More information

Series BC 58. Absolute Rotary Encoder Series BC 58

Series BC 58. Absolute Rotary Encoder Series BC 58 Mechanical specifications Shaft diameter Shaft load 6 mm (synchro flange) 10 mm (clamping flange) 10/12 mm (blind hollow shaft) Series BC 58 E Absolute single- and multiturn rotary-encoder with solid shaft

More information

Online data sheet DFS60A-TEPZ00S09 DFS60 INCREMENTAL ENCODERS

Online data sheet DFS60A-TEPZ00S09 DFS60 INCREMENTAL ENCODERS Online data sheet DFS60A-TEPZ00S09 DFS60 A B C D E F H I J K L M N O P Q R S T Illustration may differ Detailed technical data Features Special device Specialty Ordering information Other models and accessories

More information

TECHNICAL DATASHEET Absolute Encoder AC 36 - BiSS / SSI

TECHNICAL DATASHEET Absolute Encoder AC 36 - BiSS / SSI Overall length: 36 mm For equipment engineering and industry Up to 17 Bit Resolution Singleturn + 12 Bit Multiturn Solid shaft 6 mm (Hollow shaft version: AD 36) +100 C operating temperature 10,000 rpm

More information

Incremental encoders Blind hollow shaft or cone shaft pulses per revolution

Incremental encoders Blind hollow shaft or cone shaft pulses per revolution Features TTL output driver for cable length up to 550 m Very high resistance to shock and vibrations Hybrid bearing for extended service life Shaft insulation up to.8 kv Large terminal box, turn by 80

More information

Online data sheet AFS60B-S4PA AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFS60B-S4PA AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FS60-S4P032768 FS/FM60 SSI FS60-S4P032768 FS/FM60 SSI C D E F Ordering information Type Part no. FS60-S4P032768 1037483 Other models and accessories www.sick.com/fs_fm60_ssi Illustration

More information

Absolute encoders multiturn

Absolute encoders multiturn The Sendix M6 with Energy Harvesting Technology is an electronic multiturn encoder in miniature format, without gear and without battery. With a size of just 6 x 5 mm it offers a blind hollow shaft of

More information

Absolute Rotary Encoder EXAG Explosion Proof. Device Net

Absolute Rotary Encoder EXAG Explosion Proof. Device Net Main Features - Approval: II 2 G/D EEx d II C T6 - Heavy-duty industrial model - Interface: - Max. 65536 steps per revolution (16 Bit) - Max. 16384 revolutions (14 Bit) - Code: Binary Programmable Parameters

More information

ABSOLUTE ROTARY ENCODER DEVICE NET

ABSOLUTE ROTARY ENCODER DEVICE NET Main Features - Compact and heavy-duty industrial model - Interface: CAN according to Device Net - Housing: 8 mm - Shaft: 6 or 0 mm - Resolution: Max. 2 Bit =,,2 steps over,096 revolutions - Code: Binary

More information

RM36. Rotation sensors RM36 Absolute rotary encoder

RM36. Rotation sensors RM36 Absolute rotary encoder Rotation sensors RM36 Absolute rotary encoder RM36 Description The RM36 is a high-speed magnetic rotary encoder designed for use in harsh industrial environments. The non-contact two-part design removes

More information

TECHNICAL DATASHEET Absolute Encoder AC 36 - BiSS / SSI

TECHNICAL DATASHEET Absolute Encoder AC 36 - BiSS / SSI Overall length: 36 mm For equipment engineering and industry Up to 22 Bit Resolution Singleturn + 12 Bit Multiturn Solid or hollow shaft version available +100 C operating temperature 10,000 rpm (continuous)

More information

QR12. Output. A = Line Driver B = Line Driver ABZ/ Open Collector UVW C = Sin/Cos/ Line Driver UVW D = Sin/Cos/Open Collector UVW

QR12. Output. A = Line Driver B = Line Driver ABZ/ Open Collector UVW C = Sin/Cos/ Line Driver UVW D = Sin/Cos/Open Collector UVW QR12 DESIGN FEATURES Low profile assembled height of 0.99" Bearing design simplifies encoder attachment Resolutions up to 20,000 lines per revolution SIN/COS outputs available up to 1250 LC 4, 6 or 8 pole

More information

Lexium integrated drives

Lexium integrated drives Description ILp for CANopen, PROFIBUS DP, RS ILA with AC synchronous servo motor Description ILA comprise control electronics with a fieldbus interface for CANopen DS, PROFIBUS DP or RS and an AC synchronous

More information

DS Absolute Position, Rotary Electric Encoder

DS Absolute Position, Rotary Electric Encoder DS-90-64 Data Sheet, V 1.0, Jan. 2010 DS-90-64 Absolute Position, Rotary Electric Encoder The DS-90 is a member of the DS series of Electric Encoders, based on Netzer Precision proprietary technology.

More information

Absolute Rotary Encoder EXAG Explosion Proof. Canopen

Absolute Rotary Encoder EXAG Explosion Proof. Canopen Main Features - Approval: II 2 G/D EEx d II C T6 - Heavy-duty industrial model - Interface: CAN - Protocol: - Max. 65536 steps per revolution (16 Bit) - Max. 16384 revolutions (14 Bit) - Code: Binary Programmable

More information

Product Overview. Rotary Encoders with Optimized Scanning

Product Overview. Rotary Encoders with Optimized Scanning Product Overview Rotary Encoders with Optimized Scanning November 2006 Rotary encoders for electrical drives are subject to high requirements: they are expected to function reliably and provide dependable

More information

FVS58 singleturn absolute encoder. FVS58. Technical Product description data Incremental encoders special designs. Technical data

FVS58 singleturn absolute encoder. FVS58. Technical Product description data Incremental encoders special designs. Technical data absolute encoder Industrial standard housing Ø58 mm 1 Bit singleturn Output code: Gray and binary Short-circuit proof push-pull output Inputs for selection of counting direction, LATCH and PRESET Code

More information

Magnetic Sensor - Incremental / Absolute WMSA50

Magnetic Sensor - Incremental / Absolute WMSA50 singleturn sensor magnetic sensing 2port output (absolute + incremental simultaneously) Interface: SSI (synchron serial interface) BiSS (Bidirectional serial synchron) SPI (serial peripheral interface)

More information

DG 60 L Incremental Encoder

DG 60 L Incremental Encoder Incremental Encoder Features Incremental encoder with 60 mm outer diameter ugged die-cast aluminum housing Quadrature output with reference marker, complementary output signals Protection to IP 67 Square

More information

Incremental Encoder for special applications

Incremental Encoder for special applications Model Number Features Up to 50,000 ppr Extended temperature range Industrial standard housing Ø58 mm Servo or clamping flange 10 V... 30 V with short-circuit proof push-pull output Description High performance

More information

Positioning drives DC motor, brushless Absolute multiturn position detection, Profibus-DP

Positioning drives DC motor, brushless Absolute multiturn position detection, Profibus-DP Features Positioning drive with worm gear bevel geared shaft Profibus-DP Brushless DC motor Absolute multiturn position detection Nominal power output 80 W inputs programmable Separate communication and

More information

Magnetic absolute encoder GEL 2035 Serial interface (SSI), 24 Bit

Magnetic absolute encoder GEL 2035 Serial interface (SSI), 24 Bit Magnetic absolute encoder GEL 2035 Serial interface (SSI), 24 Bit Technical information Version 03.09 Resolution: Precision: 0.8 Signal pattern: Singleturn (ST): Multiturn (MT): up to 24 Bit SSI and SSI

More information

Data Sheet AS25/AS50. Absolute / Incremental Singleturn Encoder 18 Bit

Data Sheet AS25/AS50. Absolute / Incremental Singleturn Encoder 18 Bit Absolute / Incremental Singleturn Encoder 18 Bit PWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany Phone: +49 3691 72580-0 Fax: +49 3691 72580-29 info@pwb-encoders.com info@pwb-encoders.com / Description

More information

Absolute encoder GEL 15X F. Serial (SSI) or parallel interface, PC-programmable. Technical information version 01.06

Absolute encoder GEL 15X F. Serial (SSI) or parallel interface, PC-programmable. Technical information version 01.06 Absolute encoder 5xF Serial (SSI) or parallel interface, PC-programmable Technical information version 0.06 converter module KM 50.0 - + 24 V DC + 0% 5X F connecting cable VK 50.2 (SSI) VK 50.3 (parallel)

More information

Incremental hollow shaft encoder BRIH EcoMag

Incremental hollow shaft encoder BRIH EcoMag Incremental hollow shaft encoder BRIH EcoMag features miniaturized hollow shaft encoder with wide pulse range radial cable connection or connector end shaft mounting up to mm general data voltage supply

More information

Data Sheet for Angle Sensors

Data Sheet for Angle Sensors ETA25PM - R ETA25PM - F ETA25PM - TS 10 to 100-times longer life compared with multiturn potentiometers Free user programmable start and end position (electrical angle 10 up to 72000 ) Simple user programming

More information